TECHNICAL DOCUMENTATION

SSP 990293 – The 2019 Audi A8 Infotainment and Audi Connect Systems

PDFEN56 pages6 MB
SSP 990293 – The 2019 Audi A8 Infotainment and Audi Connect Systems - PDF cover

This PDF is currently unavailable.

Read document text
The 2019 Audi A8 Infotainment and Audi Connect SystemseSelf-Study Program 990293 Audi of America, LLC Service Training Created in the U.S.A. Created 06/2018 Course Number 990293©2018 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Revision 1: Jun 14, 2018The eSelf-Study Program (eSSP) teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. For further information about maintenance and repair work, always refer to the current technical literature.NoteReferenceii Modular infotainment matrix generation 2+Introduction Design Operating concept MIB2+ High with navigation systemRear Seat Entertainment 22 2 4 9 Rear Seat Entertainment4040Audi connectIntroduction Using the Audi connect services Audi connect stolen vehicle locator4141 43 44Drives and external connectionsUSB Distributor R293 USB Connection 1 U41  DVD Changer R1611111 11 12Appendix Glossary eSelf-study programs4646 51RadioIntroduction DAB tuner1313 13Knowledge assessment52NavigationRoute calculation Connected Points of Interest (POIs) New feature in route guidance Navigation information1414 14 15 16Display and operating unitsIntroduction Technical features Networking Function Other features Button combinations for service1717 17 17 18 18 19Sound20Introduction 20 Bang & Olufsen Premium Sound System with 3D sound (9VS) 21 Bang & Olufsen Advanced Sound System with 3D sound (8RF) 23AntennasRear window Bluetooth Wi-Fi Roof Antenna Antenna filter for GPS R110 Mobile phone antennas2525 27 27 28 28 29Audi phone boxGeneral information Mobile Device Charger 1 J1146 Mobile Device Charger 2 J1147 Diagnosis Function displays3131 32 32 33 33Rear Seat RemoteDesign Function Diagnosis3434 35 36NetworkingTopology Image transfer3737 39iii The MIB2+ generation ↗ of the modular infotainment matrix of the 2019 Audi A8 is a fundamental revolution for Audi models regarding information and entertainment in a vehicle. It represents a new milestone for the entire Audi product range.The 2019 A8 comes standard with MMI Navigation Plus. The performance of the system, the introduction of new functions and hardware, the innovative operating concept and the further integration of the Internet in both convenience and safety/security-related applications make travelling in the Audi A8 an exceptional experience. Due to the modular structure of Information Electronics Control Module 1 J794, this experience will continue to take on new dimensions.666_0021 Modular infotainment matrix generation 2+IntroductionIncreasing requirements in the area of operation, communication and display make ever more powerful devices necessary. To meet these requirements, Information Electronics Control Module 1 has been significantly modified with the introduction of MIB2+. Compared to the previous MIB2 structure, the following modifications have been made: ›› Computing power increased by a factor of 1.5. ›› Memory capacity increased by a factor of 2. ›› Graphics performance for the displays increased by a factor of 2.DesignThe standard SD card reader↗ and the optional SIM card reader are no longer in J794 but have been moved to a shared module with the USB connections↗. This module is referred to as the Audi music interface; the designation is USB Distributor R293. J794 also now no longer has an optical drive (CD ↗ or DVD ↗). An optical drive is now only available as a separate control unit (optional equipment). J794 has two modules which cannot be separated in service: the RCC module and the MMX module. Components of the RCC module are not subject to rapid technological changes whereas the components of the MMX will need to be modified more quickly for future device generations. Components in the RCC include: ›› Radio tuner ›› Sound amplifiers ›› CAN and MOST interface ›› Diagnostic software ›› Gyroscope Components in the MMX include: ›› Main processor ›› Graphics chip ›› Bluetooth module ›› Wi-Fi module ↗ (antenna is located separately) ›› LTE mobile phone module ↗ (telephone and data up to 300 Mbit/s) ›› NavigationMMXRCC666_0052 MMI Navigation plus (I8T + 7UG)662_18710.1" touchscreen with 1540 x 720 pixel resolution 8.6" touchscreen with 1280 x 660 pixel resolution Audi virtual cockpit (9S8) 3D SSD navigation system (7UG) AM/FM radio Audi connected Radio (Internet radio) Satellite radio for North America (Sirius) (QV3) Audi music interface with 2 USB ports, 1 SDXC card reader Bluetooth interface (9ZX) UMTS/LTE data module (EL3) including Audi connect (IT3) DVD changer (6G2 - front and rear are optional) Audi music interface in the rear with 2 USB ports (UF8) Optional Audi smartphone interface (IU1) Rear Seat Remote (QW5) Audi phone box (including wireless charging) (9ZE) Optional Bang & Olufsen Premium Sound System with 3D sound (9VS) Standard Bang & Olufsen Advanced Sound System with 3D sound (8RF) Optional DAB digital radio Auto SOS & connect vehicle-specific services (IW3) Integrated Rear Seat Entertainment including 2 Audi tablets (9WF)3 Operating conceptIntroductionThe introduction of touch displays and the reduction of controls in the center console brings a new operating concept to the 2019 Audi A8. Using the MMI in the Audi A8 is similar to using a smartphone. The system is based on intuitive, self-explanatory procedures. Typical smartphone movements, such as swiping or moving items, can now be used to operate the MMI.666_0724 Upper displayThe upper touch display allows the user access to the main functions and to the corresponding sub-menus. Unlike in previous MMI generations, there is no Audi connect menu in MIB2+. With a small number of exceptions (weather, news, etc.), all connect services are assigned to the corresponding main functions and are therefore not visible on the home screen. The layout of the function tiles on the home screen can be configured by holding and sliding the tiles. Frequently used functions can be selected using shortcuts on the left edge of the display. Customers can adjust the assignment and position of the shortcuts according to their personal preferences. The only exception is the home button; this is fixed in the left menu.666_073Swiping downward from the upper edge opens a selection of four permanently defined shortcuts: ›› ›› ›› ›› Sound settings. MMI settings. Connections. User profiles.666_074666_075A display at the top right (always visible) includes information on: ›› ›› ›› ›› Bluetooth. User profile. Reception status. Data transfer.666_0765 Lower displayThe main purpose of the lower display is to operate the climate control system and activate permanent and personalized shortcuts. The personalized shortcuts may include telephone contacts, radio stations, navigation destinations and vehicle settings which have been copied from the upper to the lower display for a convenient selection. Tapping the center button at the top edge of the display allows the user to display and hide the shortcuts. These are selected without the user needing to preselect the main function (for example, navigation destinations, telephone contacts, radio stations, etc.). They are in a row on a toolbar and can be identified quickly and easily by the different tile colors. The user always has the option of changing their layout. The permanently defined shortcuts, however, are vehicle functions which may be present depending on the vehicle’s equipment. These shortcuts are at the top and bottom of the display. The center button on the lower toolbar can be used to change the assignment of the buttons to its immediate left and right according to personal requirements (see magnified section).666_077666_078666_079It is also possible to enter navigation destinations, addresses, telephone numbers, etc. by hand on the lower display. This has been made much more convenient. The system detection is now more precise and quicker. Unlike in the recent MMI touch system, entire words can now be entered without pauses. The letters do not even need to be written next to each other. The entry can be made in one place.666_080If a telephone number entered is not clear, the system suggests possible alternatives on the upper display.666_0816 The delete function has been optimized significantly. It is possible to delete as many characters as desired by swiping left. If the user deletes too many characters by accident, they can be restored by swiping in the other direction.666_082666_083666_084666_085666_086666_0877 8 MIB2+ High with navigation systemThe MMI navigation plus has the following features as standard: ›› Radio with phase diversity, FM dual tuner (very high frequency) and AM tuner (medium wave) and background tuner. ›› 3D navigation with data on SSD with improved 3D city center models (7UG). ›› LTE-enabled mobile network module, possible data transfer rates of up to 300 Mbit/s (EL3) for: ›› Audi connect active license (IT3) including Wi-Fi hotspot with a possible data transfer rate of up to 150 Mbit/s. ›› Navigation with online routing. ›› Internal audio amplifier, 180 W (9VD). ›› Bluetooth interface for HFP, A2DP and MAP (9ZX). ›› Speech dialog system. ›› 1 image output for Audi virtual cockpit. ›› 1 image output for both touch displays (1540 x 720 and 1280 x 660 pixels). ›› Audi music interface with 1 SDXC card reader, 2 USB sockets (UF7) and, depending on market, 1 SIM card reader (EL3). The following additional equipment can be ordered: ›› Functions integrated in J794: ›› DAB dual tuner (digital radio) (QV3). ›› SDARS tuner (North America digital radio) (QV3). ›› Audi smartphone interface (IU1). ›› Functions in separate control units: ›› DVD changer (6G0)¹). ›› Front Audi phone box (9ZE). ›› Rear Audi phone box (QF7). ›› Rear Seat Remote (QW5). ›› 2 Audi tablets (9WF). ›› Bang & Olufsen Premium Sound System with 3D sound and 660 W (9VS). ›› Bang & Olufsen Advanced Sound System with 3D sound and 1920 W (8RF).Connections on Information Electronics Control Module 1 J794 Main menu on MMI navigation plus666_009USB Distributor R293666_0479 GPS LTE antenna 2 LTE antenna 1 USB-AMI LVDS to virtual cockpit LVDS to touch displaysDriver Assistance Systems Control Module (zFAS) J1121Wi-Fi666_010MOST bus Ethernet USB to DVD player FM2 FM1/AM DAB Composite video plus from rear view cameraMIB-CAN HighInfotainment CAN High Infotainment CAN Low MIB-CAN Low Composite video minus from rear view camera666_01210 Drives and external connectionsUSB Distributor R293R293 has two USB connections and one SDXC card reader. R293 is connected to Information Electronics Control Module 1 J794 by a USB interface. All diagnosis functions for R293 are stored in J794 and can be accessed via Address Word 005F using the VAS Scan Tool. The USB connections support the USB 2.0 standard. Each connection can provide charging current up to 1.6A.USB Distributor R293666_047Every 2019 Audi A8 will be equipped with the Audi music interface (AMI). Together with the software in Information Electronics Control Module 1 J794, the system requires USB Distributor R293.666_015USB connection to U41USB connection to J794USB Distributor R293 (back)USB Connection 1 U41Two USB connections are available optionally in the rear of the Audi A8. They are integrated in USB Connection 1 U41 and are installed with by ordering the “Audi music interface in rear” (UF8). USB Connection 1 U41 is connected to the USB Distributor R293 via a USB interface. Its signal is sent from R293 to J794. All diagnosis functions for U41 are performed via J794. The connections support the USB 2.0 standard. Each connection can provide charging current of up to 2.1 A.USB Connection 1 U41666_016USB connection to R293USB Connection 1 U41 (rear)666_017Note The optional Audi smartphone interface (IU1) can only be used via the two front USB connections in R293.11 DVD Changer R161The optional DVD changer R161 is also used on the Audi Q7. This drive is a dedicated DVD video drive which only allows playback of video DVDs and audio CDs. R161 is connected to J794 via the MOST bus. It is located between the rear seat backrests. It is diagnosed via Address Word 000E Media player position 1.DVD Changer R161666_020DVD Changer R161 (rear)666_02112 RadioIntroductionThe following new features are being introduced to the entire radio system as part of MIB2+: ›› DAB tuner (3x). ›› One station list for FM, DAB and Internet radio stations. All functions are implemented by Information Electronics Control Module 1 J794. These can be diagnosed via Address Word 005F using the VAS Scan Tool.Menu for selecting radio source666_038Radio station list666_119DAB tunerWith MIB2+, a third tuner and a second DAB antenna have been added to the DAB radio. Tuners 1 and 2 receive the signal of the station currently selected and decode it. The bits of both tuners are then compared in the MRC module (maximal ratio combining). If it is determined that bits are missing in a tuner, they can be replaced with the bits from the other tuner. This creates better reception. In the background, tuner 3 searches for new stations to keep the station list continually updated. In addition, it provides the navigation unit with traffic information.Tuner 1 DAB decoder MRC module Audio amplifierTuner 2 DAB decoder DAB decoder for station list and navigationTuner 3MOST interface Sound processorNavigationIllustration of DAB tuner (example)666_039Reference For further information on the radio tuner, please refer to eSelf-Study Program 970143, Modular Infotainment Platform (MIB).13 NavigationWith MIB2+, Audi is making use of “connected navigation”. ›› Online routing (cloud-based route calculations)*. ›› 3D city models in some towns/cities with detailed and accurate depictions of streets and buildings.* ›› Connected POIs with additional information on the map.* ›› Traffic sign information. ›› Hazard alerts.* ›› Navigation display with Google Earth.* *These items require Audi connect PRIME.Route calculationRoute calculation takes place in Information Electronics Control Module 1 J794. This is where the map data is stored. If there is an existing data connection, (that is. Audi connect PRIME) a route is calculated on a central Audi server at the same time. The calculation on the server is quicker than the one in J794, particularly when the destination is far. In addition, the calculation takes the entire traffic situation into account. The same map data as in J794 is used for the online route calculation. As a result, the driver is offered up to three alternative routes. There is no longer an option to set route types such as “short”, “fast”, or “economical”.666_088Connected Points of Interest (POIs)In MIB2+, selected Audi connect services (for example, fuel prices, parking information, etc.) have been integrated in the navigation function.Additional information on certain POIs is displayed directly in the list or when a POI is selected on the map.666_08914 New feature in route guidanceManeuver previewThe maneuver preview has been reduced to the next two actions. If desired, the user can extend the preview to 10 maneuvers.Manual traffic avoidanceA corresponding display on the right side menu helps the driver with manual traffic avoidance. It calculates the actual time saved if the alternative route were used.666_090Personal route assistJ794 identifies routes which are driven repeatedly and suggests possible destinations. If there are potential delays on routes that the system suspects the driver may take, it will automatically suggest alternative routes, even when route guidance is not active. This “self-teaching” navigation system is referred to as personal route assist in MIB2+. If the personal route assist function is deactivated, a selection field appears on the right side showing a checkered flag with a light bulb. To activate the function, the customer can simply tap the field.666_120666_091666_092Optimized position detectionWith the introduction of Driver Assistance Systems Control Module J1121, the vehicle can be localized to a specific lane. J1121 makes the necessary calculation and sends the information to J794 which can then provide a lane-specific display. This is shown in the “exit views”¹), both on the Audi virtual cockpit and the head-up display. Despite the display being precise to a specific lane, spoken cues may be given which appear unnecessary to the driver because the car is in the correct lane. If the vehicle drives past an exit, for example, the spoken cue will still tell the driver to keep left.666_093666_094¹)  Exit views refer to leaving highways and major roads.15 Navigation informationNavigation data storageAt the launch of the Audi A8, J794 will have up to 25 GB of navigation data stored. In addition, 15 GB are kept available for cached navigation information (Google, 3D city data, online hazard alerts etc.). The maximum space available for the navigation system on the SSD ↗ is approximately 64 GB of the 128 GB available in total.Map updateMMI navigation plus customers will receive a free 6 month trial of Audi connect PRIME. As long as the subscription is active, the customer will receive free navigation updates. For the latest information on the various Audi connect offerings, refer to the Audi connect portal. https://www. audiusa.com/technology/intelligence/audi-connect The navigation data have been changed to a new format for MIB2+. This “navigation data standard” (.nds) format allows incremental updates. These are updates which only affect the data which have changed, allowing updates to be quicker. In addition, the geographic regions have been made smaller. This helps to accelerate the update process. The average size of the update data is now 10% of the previous amount.666_09516 Display and operating unitsIntroductionAudi is taking a new path with the 2019 Audi A8 and is introducing touch displays for the first time. For marketing purposes, these are referred to as “MMI touch response”. They are multitouch displays; this means that they can be operated with several fingers at once. Two high-definition displays are installed in the Audi A8. The upper display (“MMI display”) is used to display the MMI. The lower display ("lower touch display”) is used, among other things, to operate the climate control. The high resolution and small pixel dimensions of these displays are crucial for a very clear picture: the human eye is not capable (at the typical distances in the vehicle interior) of detecting the individual pixels from which the image is constructed. The maximum brightness is 900 candela ↗. It can be adjusted on the MMI.Technical featuresMMI display Front Information Display Control Head J685. ›› 10.1 inch ›› 1540 x 720 pixels ›› Active area: 232 x 109 mm Lower touch display Front Information Display Control Head 2 J1060 ›› 8.6 inch ›› 1280 x 660 pixels ›› Active area: 194 x 100 mmNetworkingBoth displays are controlled by J794 and connected to it via MIB-CAN. All fault memory entries and adjustments are stored/made in J794. J794 sends a common image (a “superframe”) to the MMI display J685 via two LDVS wiring pairs. J685 then sends the part of the image for the lower touch display J1060 to that display via two LDVS wiring pairs. To ensure that they are not mis-connected, the two LVDS connectors on J685 are of different colors.666_013Front Information Display Control Head J685Front Information Display Control Head 2 J1060666_01417 FunctionThere are pressure sensors behind the touch-sensitive display surface. They enable the MMI to be used more safely as they allow the user to move fingers over the display without making undesired inputs. The system only reacts to a specific amount of pressure or more on the display; this is detected by the pressure sensors. To provide the user with tactile and audible feedback simulating the touch of a button, an electromagnet and a speaker are integrated into each display. If the pressure sensors detect that the screen has been pressed intentionally, the electromagnet moves the surface of the display very slightly sideways. The speaker plays a clicking sound. This haptic and acoustic reaction is the feedback typical to Audi. It is possible to set the level of pressure which has to be exerted on the display for feedback to be given. There are three levels for this. The feedback can be deactivated in steps as follows:1. Haptic feedback 2. Acoustic feedbackConnection from J794Connection to J1060666_042Front Information Display Control Head J685 (rear)Other featuresBoth displays have a special coating to make it easier to remove finger marks. There is a freeze function which allows the user to clean the surface of the display without making unwanted changes to the system. J685 has hardened, shatter-proof glass which is capable of surviving an impact from a 15.4 lb (7.0 kg) metal ball travelling at 12.4 mph (20 km/h) undamaged. For design reasons, the upper display is horizontally curved. This allows it to be integrated flush into the instrument panel.Connection from J685 Front Information Display Control Head 2 J1060 (rear)666_04318 Button combinations for serviceIn the past, button combinations of the MMI operating units were used for certain functions, such as recording the current display on the MMI (screenshot). Other activation options have been introduced for the new touch display (MMI touch response). Procedures for service are given below.System resetTo restart (reset) the MMI, press and hold the Driver Volume Control E67 for at least 10 seconds.Driver Volume Control E67666_044Engineering menuTo access the engineering menu, touch the MMI display J685 at the top right with two fingers for at least three seconds.Touch location for engineering menu666_045ScreenshotTo make screenshots of both touch displays, touch the MMI display J685 with two fingers at the bottom in the center for at least three seconds. Five images are stored in J794 at the same time. Two images are stored for each touch display; one screenshot of the screen display and one of the control areas. The fifth screenshot shows the image sent from J794 to the Audi virtual cockpit. The display view flashes briefly to confirm that the screenshot has been saved. The saved screenshots can be downloaded from J794 and copied to an SD card using the VAS Scan Tool through Guided Functions. This can be done via the selection “005F - Information electronics 1, functions”, “005F - Basic setting” and, in the program sequence, via the option “Write analysis data on SD card”.Touch location for screenshot666_04619 SoundIntroductionThe following sound systems are available to Audi A8 customers: ›› Bang & Olufsen Premium Sound System with 3D sound (9VS) (16-channel) ›› Bang & Olufsen Advanced Sound System with 3D sound (8RF) (24-channel) The Audi sound system (9VD) has 6 channels and 10 speakers with a total power output of 180 W. The Advanced Sound System (8RF), has 24 channels and a total power output of 1920 W, shared between 23 speakers. Both Bang & Olufsen systems can generate the third dimension of 3D sound using a special algorithm. To do this, the Premium Sound System has two speakers in the A-pillars; the Advanced Sound System uses four. The two additional speakers are in the headliner, behind the grab handles. On the Bang & Olufsen Advanced Sound System, the two treble speakers in the instrument panel are retractable. The subwoofer is under the rear shelf and installed in a special bracket. In addition to the Vehicle Noise Cancellation function (VNC), some vehicles also have the Active Noise Cancellation function (ANC) (PR number EP1). Four microphones in the headliner record noises caused by the engine and initiate appropriate compensation noises.Note Active noise cancellation (PR number EP1) on V8 models only. Not available at launch.Reference For more information on the “Active Noise Cancellation” function, please refer to eSelf-Study Program 920223,The Audi 4.0L V8 TFSI Engine.20 Bang & Olufsen Premium Sound System with 3D sound (9VS)Right Front Midrange Speaker R104 Right Front Midrange Speaker 2 R277Right Front Treble Speaker R22Right Front Bass Speaker R23 Center Speaker R208Center Speaker 2 R219Left Front Treble Speaker R20Left Front Midrange Speaker 2 R276Left Front Midrange Speaker R103Left Front Bass Speaker R21Left Rear Treble Speaker R14Left Rear Bass Speaker R1521 Right Rear Treble Speaker R16 Right Rear Bass Speaker R17 Left Effects Speaker R209Right Effects Speaker R210Subwoofer R211Digital Sound System Control Module J525666_02322 Bang & Olufsen Advanced Sound System with 3D sound (8RF)Right Front Midrange Speaker R104 Right Front Midrange Speaker 2 R277Right Front Treble Speaker R22Right Front Bass Speaker R23 Center Speaker R208Center Speakerr 2 R219Left Front Treble Speaker R20Left Front Midrange Speaker 2 R276Left Front Midrange Speaker R103Left Front Bass Speaker R21 Left Rear Treble Speaker R14 Left Rear Bass Speaker R15 Left Rear Midrange Speaker R10523 Right Rear Treble Speaker R16 Right Rear Midrange Speaker R106 Right Rear Bass Speaker R17 Right Rear Midrange Speaker 2 R340 Right Effects Speaker R210Right Rear Treble Speaker 2 R218Subwoofer R211Left Effects Speaker R209Digital Sound System Control Module J525Left Rear Midrange Speaker 2 R341Left Rear Treble Speaker 2 R217666_02424 AntennasRear windowThe antennas for radio reception are integrated in the rear window. There are differences depending on the window type. The Audi A8 has a total of three types of rear windows. The antenna structure is very similar on TSG¹) and LSG²) (privacy windows) (image 666_025). This is not the case with insulated glass. Its particularly powerful heating wires are installed in a special foil and cannot be used as antennas (image 666_026, page 27)¹) Tempered safety glass ²) Laminated safety glassAntenna Amplifier 2 R111DAB antennaAM antennaDAB connection FM2 connection25 AM antennaDAB antenna 2 (wire marked in green)Antenna Amplifier R24FM1/AM/DAB connection666_02526 DAB connection FM2 connection Antenna Amplifier 2 R111DAB antennaAM antennaDAB antenna 2FM1/AM/DAB connection Antenna Amplifier R24666_026BluetoothThe Audi A8 may be equipped with up to two Bluetooth antennas. One is used to connect external devices to the MMI and is located in Information Electronics Control Module J794. The second one is optional. It is integrated in the roof antenna and connected at Driver Assistance Systems Control Module J1121 (zFAS). Both antennas support Bluetooth Low Energy (standard 4.0). This standard provides for a maximum range of approximately 10.9 yd (10 m).Wi-FiIn the Audi A8, Vehicle Interior Communication Antenna R364 is located on the base of the interior rear view mirror. It is no longer in J794. It now supports two frequencies: 2.4 GHz and 5 GHz. This allows even better reception. The Wi-Fi standard is 802.11 ac. At 5 GHz, the data transfer is up to 300 Mbit/s. If the conditions are met, the Audi tablet and the Rear Seat Remote always use the 5 GHz frequency. All other mobile devices which are connected to J794 via Wi-Fi determine which frequency to use themselves.Reference The Bluetooth antenna in the roof antenna is not yet available at the launch of the 2019 Audi A8 . Further information will be provided at a later date.27 Roof AntennaThe following connections in the roof antenna are possible in North America: ›› SDARS ›› Navigation ›› Telephone Because of the different openings on glass and steel roofs, there are different roof antennas for each version.Antenna filter for GPS R110If the Audi vehicle tracking system (PR number 7I1/7I2), the signal from the GPS antenna is split in GPS Antenna Splitter R110. The GPS signal is forwarded from R110 to J794 and J533 (connected gateway). R110 is installed directly in the wiring harness. The antenna filter is a passive component and does not have self-diagnostic capability. Diagnosis of the GPS antenna is performed by J533. If there are problems, R110 should be considered.SDARS NavigationTelephone Roof antenna (glass roof, North America)666_028Signal input from roof antenna666_029Signal output to J533 GPS Antenna Splitter R110Signal output to J79428 Mobile phone antennasThe roof antenna of the 2019 A8 is used for both Information Electronics Control Module 1 J794 and Data Bus On Board Diagnostic Interface J533. In most cases the signal from the roof antenna is sent from J533 directly to J794. If J533 requires use of the roof antenna, for example, in the event of an Audi emergency call, the connection to J794 is ended. A second antenna is connected to J533. It is installed in the rear bumper. J533 determines which of the two antennas to use for communication based on the signal strength. The LTE Advanced standard with carrier aggregation is used in the Audi A8. In this system, the signal is not transmitted via only one channel, but via several at the same time. This increases the bandwidth ↗ accordingly and allows for higher data transfer rates. Data transfer rates of up to 300 Mbit/s can therefore be achieved. The number of mobile phone antennas in the Audi A8 is variable. Depending on the vehicle’s equipment, there may be up to three antennas in the bumper, one on the roof and one under the rear right side window.LTE Antenna 1 R297 Emergency Call Module Antenna 2 R322LTE Antenna 2 R306 Cellular Telephone Amplifier 2 R328LTE Antenna 4 R331Cellular Telephone Amplifier R86Emergency Call Module Antenna R263666_030LTE Antenna 3 R33029 VersionsDiagrams of antenna configurations are provided below. They depend on the vehicle’s equipment. The maximum possible number of antennas is shown.Vehicles without Audi connect vehicle-related services (IW0)Information Electronics Control Module 1 J794 Mobile Device Charger 2 J1147 Cellular Telephone Amplifier 2 R328 LTE Antenna 4 R331 LTE/UMTS/GSM Voice/dataLTE Antenna 2 Data R306 Mobile Device Charger 1 J1146 LTE Antenna 1 LTE/UMTS/GSM Voice1)/data R297 Cellular Telephone Amplifier R86 LTE Antenna 3 R330 LTE/UMTS/GSM Voice/data666_031Vehicles with Audi connect vehicle-related services (IW3)Information Electronics Control Module 1 J794GPS Antenna Splitter (only installed with vehicle tracking system) R110LTE Antenna 2 Data R306Data Bus On Board Diagnostic Interface (connected gateway) J533Emergency Call Module Antenna 2 R322 LTE Antenna 1 LTE/data R297Emergency Call Module Antenna R263666_032Note For better clarity, the optional Audi phone boxes are not illustrated on the image “Vehicles with Audi connect vehicle-related services”.30 Audi phone boxGeneral informationUp to two Audi phone boxes are available for the Audi A8. Both are capable of self-diagnosis at Audi (for the first time at Audi) and participants in MIB-CAN. The designation in service is: For the front Audi phone box: ›› Mobile Device Charger 1 J1146. For the rear Audi phone box: ›› Mobile Device Charger 2 J1147. Depending on the vehicle’s equipment, the control module hardware may be identical. Because of the different diagnosis Address Words, they must be installed in the correct location. They have different part numbers to help ensure that they are not interchanged. In the Audi A8, the Audi phone box supports the LTE standard along with GSM and UMTS. LTE-enabled compensors (antenna amplifier for mobile telephone) are installed for this. The Qi standard is supported for the wireless charging function.Telephone antennaAntenna circuit board666_068Charging coils for wireless charging LTE antenna input NFC antenna outputNFC antennaCircuit boardPower supply and MIB-CAN666_067Mobile Device Charger 1 for mobile devices666_04931 Mobile Device Charger 1 J1146The Audi phone box is available in the following option dependent versions: ›› With external antenna connection and wireless charging (9ZE). ›› Without external antenna connection, wireless charging only (9ZV). The display showing information on the charging status of a smartphone in the front Audi phone box is displayed in the MMI menu. The compensor belonging to the charging unit J1146 has the designation Cellular Telephone Amplifier R86.Mobile Device Charger 1 for mobile devices with Audi connect key666_050Cellular Telephone Amplifier R86666_069Mobile Device Charger 2 J1147Three option dependent versions of J1147 are available: 4-seat vehicle ›› Wireless charging only (QF6). ›› External antenna connection and wireless charging (QF7). 5-seat vehicle ›› External antenna connection only (QF8). On 5-seat vehicles, the rear Audi phone box is installed in the center armrest. Wireless charging is not available here because of cooling difficulties. The rear Audi phone box only has the external antenna connection; its PR number is QF8. The display showing information on the charging status of a smartphone in the rear Audi phone box is shown on the Rear Seat Remote. If the rear Audi phone box is not equipped with wireless charging, it is no longer a CAN control module. Its designation is then Roof Antenna  R126. R126 exchanges information with Information Electronics Control Module 1 J794 via a PWM signal. The compensor belonging to Mobile Device Charger 2 has the designation Cellular Telephone Amplifier 2.Mobile Device Charger 2 J1147666_051Note The switch-on information for both compensors is still provided by Information Electronics Control Module J794 as a 12V signal.32 DiagnosisAddress Word 00DE is used to diagnose Mobile Device Charger 1. Mobile Device Charger 2 J1147 is diagnosed via Address Word DF. Along with MVs, it is now possible to diagnose the external antenna. Any software update for the mobile device chargers is always provided to the MMI via a full update. Diagnosis for Telephone Baseplate R126 is done via Information Electronics Control Module 1 J794.666_065Function displaysThe wireless charging function can be deactivated individually for front and rear if necessary. If there is a smartphone with wireless charging function in the front Audi phone box, the charging function is shown on the front MMI display. The Rear Seat Remote (SCON ↗) shows a corresponding display if a smartphone is in the rear Audi phone box. A corresponding notification is given if a smartphone is left in the Audi phone box when the user is leaving the vehicle. This notification is triggered for the front Audi phone box when: ›› A smartphone is in the front Audi phone box ›› Terminal 15 is off ›› The door is open (Terminal S off) The notification is triggered for the Rear Seat Remote when: ›› A smartphone is in the rear Audi phone box. ›› A rear seat belt is unbuckled. ›› The corresponding rear door is open.Notification on Rear Seat Remote666_055Notification on MMI display666_054Phone box registrationWhen a customer purchases a vehicle equipped with a phone box, the phone box must be registered with their cell phone carrier. The registration information is entered on a form downloadable from ServiceNet. Dealers will find the vehicle specific information on a sticker in the luggage compartment.33 Rear Seat RemoteA Rear Seat Remote is available in the 2019 A8. The device is referred to internally as SCON (Smart Remote Control). It can be ordered as an option, but is required if the following equipment is ordered: ›› Telephone in rear. ›› 4-zone climate control. ›› Massage seats in rear. ›› Reclining rear seats. ›› Matrix reading lights in rear.Rear Seat Remote in vehicle666_058DesignThe Rear Seat Remote has two components: Auxiliary Display Control Head 1 E857 and Wireless Control Head 1 E589.Remote controlWith its 5.7” display, Wireless Control Head 1 E859 is similar to a large smartphone. Unlike a regular smartphone, however, it has been developed specifically for in-vehicle use and conforms to crash safety requirements. The display is always in landscape format, with the exception of the telephone function, which is in portrait. The remote control display has the following specifications: ›› OLED display ↗ with 1920 x 1080 pixels. ›› Permanently installed lithium-ion battery (2800 mAh). ›› Integrated speaker and microphone for telephone calls. ›› Wi-Fi connection to J794 via 5 GHz frequency. ›› Two volume buttons. All information shown on the remote control and provided directly by the vehicle is received via the Wi-Fi hotspot of J794. For this reason, Wi-Fi must be activated in J794.666_060Wireless Control Head 1 E859)666_059Power supply (minus)DataDataPower supply (minus)Power supply (plus) Connections on the remote controlPower supply (plus)Note Only one telephone call at a time can be made via J794. It is not possible to have an active call in the front via the hands-free system and in the rear via the remote control.34 Auxiliary Display Control Head 1 E857Auxiliary Display Control Head 1 E857 serves as the remote control’s mounting and power supply. It is also used for diagnostic functions and to bond a new remote control in the event of renewal. The retainer is connected to Information Electronics Control Module 1 J794 via MIB-CAN. A magnet in the retainer ensures that the remote control does not slip out when engaged in the retainer.FunctionThe Rear Seat Remote can be used to control the following functions: ›› Telephone handset ›› Radio and media ›› Sound system ›› Rear climate control system ›› Massage seats in rear ›› Reclining rear seats ›› Seat adjustment ›› Rear seat ventilation ›› Passenger seat adjustment ›› Rear Seat Entertainment ›› Interior lighting ›› Matrix reading lights ›› Panorama sunroof ›› Rear and side window blindsAuxiliary Display Control Head 1 E857 (retainer)666_061Terminal 30 MIB-CAN LowMIB-CAN High Terminal 31 Not used Not usedTelephone handset functionThe remote control must be taken out of its retainer and held like a smartphone to be used as a telephone handset. The display is only switched to portrait mode for the telephone function. The remote control does not have an integrated telephone module. It is designed as a separate handset for a smartphone connected to J794. If the rear passengers do not wish for smartphone calls to be shown on the front MMI display, they can select “Private mode”.Telephone menu display666_06335Display when private mode is active666_064 DiagnosisE857 and Wireless Control Head 1 E859 can both be accessed via Address Word 00E0 using the VAS Scan Tool. The following functions are available: ›› ›› ›› ›› Fault memory. Measured value blocks. Output check diagnosis. Adaptation.A software update for the Rear Seat Remote can only be performed in conjunction with an update of the entire infotainment system. When needed, the right button (volume down) must be held to reset Wireless Control Head 1 E859. A new remote control must always be adapted to the vehicle as it is a participant in the component protection process. Adaptation is done through Guided Functions via the Scan Tool. This process bonds the remote control to the vehicle via SVM (Software Version Management).666_065Note Because there are no handsfree microphones in the rear of the Audi A8, the rear passenger can only make and receive calls using the remote control.36 NetworkingTopologyAs many as 27 control modules are needed for all the functions of the infotainment and Audi connect systems in the 2019 Audi A8. The number of modules would of course increase if all those responsible for carrying out a service (for example, unlocking) were shown here. Therefore, this diagram only shows the control modules which are directly necessary in the maximum equipment version. Information Electronics Control Module 1 J794 exchanges the majority of data with other control modules via the MOST or CAN buses. Exceptions to this include various image data and software update data for Instrument Cluster Control Module J285 and Driver Assistance Systems Control Module J1121. A new type of data connection (Ethernet) has been added to J794. It is currently used to transfer data for a J794 software update to Driver Assistance Systems Control Module J1121 (zFAS). J794 receives the data from an SD card inserted in the USB hub.Multimedia Display Unit 4 Y32 Left Rear Information Display Control Head Control Module J648Multimedia Display Unit 3 Y31Right Rear Information Display Control Head Control Module J649Driver Volume Control E67Front Information Display Control Head 2 J1060Front Information Display Control Head J685Transfer rates of individual bus systems:Bus system Infotainment CAN Convenience CAN MOST bus MIB-CAN (local CAN data bus) Sub-bus system Ethernet LVDS USB connection Composite videoComfort System Central Control Module J393Wire colorData transfer rate↗ 500 kbit/s 500 kbit/s 150 Mbit/s 500 kbit/s 500 kbit/s 100 Mbit/sData Bus On Board Diagnostic Interface J533Close Range Communication Control Module J1169Close Range Communication Control Module 2 J1170¹) Connections only present if surround view cameras installed ²) Only installed from control module version B onwards ³) Not installed if surround view cameras installed37 Auxiliary Display Control Head 1 E857Wireless Control Head 1 E859Mobile Device Charger 2 J1147Mobile Device Charger 1 J1146USB Distributor R293USB Connection 1 U41Windshield Projection Head Up Display Control Module J898Instrument Cluster Control Module J285DVD Changer R161Information Electronics Control Module J794¹)²)Digital Sound System Control Module J525Driver Assistance Systems Control Module J1121Rearview Camera System Control Module J772³)666_06638 Image transferThere are various image sources on MIB2+. They are sent to the devices on which they are displayed in different ways. The transfer methods are: ›› ›› ›› ›› ›› MOST bus. LVDS. Composite video. Wi-Fi. USB.Information Electronics Control Module 1 J794J794 receives image data from various sources, which it then forwards to other control modules. The following control modules provide images and use the following transfer methods: ›› From mobile devices connected at USB Distributor R293 or USB Connection 1 U41, via USB. ›› From DVD Changer R161, via MOST bus. ›› From Driver Assistance Systems Control Module J1121, via LVDS. ›› From Rearview Camera System Control Module J772, via composite video.Instrument Cluster Control Module J285 (Audi virtual cockpit)The Audi virtual cockpit receives image data from J794 via LVDS and MOST bus as follows: ›› LVDS: ›› The large navigation map and the detailed intersection maps. ›› MOST bus: ›› All other content, such as list menus or covers. In addition, the MOST bus is used to transfer data for software updates.Windshield Projection Head Up Display Control Module J8898 (Head up display)Detailed intersection maps and highway exits have been added to the navigation information on J898 for the Audi A8. As the images consist of a large amount of data, J898 receives them from J794 via MOST bus.Front Information Display Control Head J685J685 receives image data for itself and Front Information Display Control Head 2 J1060 as one image from Information Electronics Control Module 1 J794 via LVDS. An integrated splitter separates this image into the section for J685 and J1060.Image transfer via Wi-FiWireless Control Head 1 E859 (Rear Seat Remote) and Multimedia Display Units 3 and 4 Y31/Y32 (Audi tablets) receive display content from Information Electronics Control Module 1 J794 via Wi-Fi. The 5 GHz frequency is generally used to do this. Data are only sent via the 2.4 GHz frequency in countries where the 5 GHz frequency is not approved. The Audi tablets do not receive any videos via the 2.4 GHz frequency if they come from drives connected to J794 (DVD player, SD card reader, USB connection).Lower touch display(display unit 2 for Front Information Display Control Head 2 J1060) The lower touch display receives the image data from the MMI display J685 via LVDS.39 Rear Seat EntertainmentRear Seat EntertainmentThe Rear Seat Entertainment system consists of the Audi tablet in the Audi A8 . This is the second generation of the Audi tablet. It can only be ordered via PR number 9WF and is only available as a set of two. Its design and functions largely correspond to the MIB2 Audi tablet in the 2017 Audi Q7. The difference compared to the MIB2 Audi tablet is in the menus; they have been adapted to the new MMI design.666_097Note Films from video sources installed in the vehicle are transmitted via the 5 GHz Wi-Fi frequency.40 Audi connectIntroductionThe Audi A8 with MMI navigation plus is equipped with Audi connect as standard. In the Audi A8, a distinction is made within the Audi connect services between infotainment and vehicle-related services. The infotainment services are designed primarily for the customer’s comfort and entertainment needs. The vehicle-related services, however, relate to the car, for example its position, condition, climate control, etc. The infotainment services are operated via Information Electronics Control Module 1 J794 and the vehicle-related services via Data Bus On Board Diagnostic Interface J533. Both control modules are equipped with their own embedded SIM card so that all Audi connect services and the Internet in general1) can be used without the use of external SIM cards. The Audi A8 may be equipped with up to two Bluetooth antennas. One of them is used to connect external devices to the MMI and is located in J794. The second one is optional. It is integrated in the roof antenna and connected to Driver Assistance Systems Control Module J1121. Both antennas support Bluetooth Low Energy (standard 4.0). This standard provides for a maximum range of approximately 10.9 yd (10 m). Audi offers its customers a complementary six-month Prime Plus unlimited subscription. Dealership personnel must complete the Audi connect key user registration process at delivery in order to initiate this free trial. For more information, refer to the following website: https:// www.audiusa.com/technology/intelligence/audi-connectThe following conditions must be met to use certain vehicle-related services, such as “Remote locking/unlocking” or “Audi service request”: ›› Verified user. ›› Key user added in the vehicle.Reference For further information on the Audi connect services, please refer to eSelf-Study Program 970663, The 2017 A4 Infotainment and Audi Connect.41 Safety & Service(up to 10 years*)Emergency CallCAREAudi Service RequestOnline Roadside AssistanceStolen Vehicle LocatorSmartphone InterfaceRERemote lock & unlockPRIME(free 6 month trial)$199 for 6 month $499 for 18 monthPLUSWiFi0 years*)(free 6 monterviceNavigation & Infotainmentmobile s unlimite Audi Service Request Google Earth™ Point-of-interest search (POI) myAudi destinations Smartphone Calendar Weather Traffic Light Info WiFi dataplans (AT&T) PRIMEStolen Vehicle Locator(free 6 month trial)Parking informationMap updatemyAudi special destinationsOnline News (RSS)Online media streaming Amazon MusicOnlinSeamless M A8/Q7/Q8/e-troTraffic information online Travel information Twitter Fuel prices Connected POIs Remote & AlertAdvanc vhone aceVehicle status reportCar finderGeofencingValet AlertSpeed/Curfew Alert Predictive route guidanceNatur recoWiFi(free 6 month trial)mobile share: $10/moWiFi dataplans (AT&T) myAudi navigationion requiredunlimited: $20/moAmazon Music Online Radio PLUSSeamless Mobility A6/A7/A8/Q7/Q8/e-tron/MY19Connected POIs Advanced 3D city viewPredictive route guidanceNatural voice recognitionmyAudi navigationKey User Registration required42 Using the Audi connect servicesThere is a significant change in the use of the Audi connect services in MIB2+: there is no longer an Audi connect menu and the majority of services are accessed via the corresponding function. For example, fuel prices are now shown directly in the navigation function.Fuel price display666_089A small number of services which cannot be easily assigned to a specific function are shown separately in the main menu. Examples of these are the “News” and “Weather” services. If desired, the customer can set shortcuts for these separately provided services on the left side of the MMI display.MMI menu with Audi connect services666_09943 Audi connect stolen vehicle locatorThe optional stolen vehicle locator (referred to in some service literature as Vehicle Tracking System [VTS]) is one of the vehicle-related services. It is designed to allow the vehicle to be found quickly if it is stolen. The customer receives a complimentary 10 year license when the vehicle is first purchased.Symbol for Audi vehicle tracking system666_071Layout in the vehicleThe vehicle tracking system has the following components in the vehicle: ›› Data Bus On Board Diagnostic Interface J533 (connected gateway) ›› Comfort System Central Control Module (BCM2) J393 ›› GPS antenna ›› Mobile phone antennas ›› Driver card (7I2 only) The following items have been added to Data Bus On Board Diagnostic Interface J533 for the vehicle tracking system function: ›› ›› ›› ›› Gyroscope Larger battery VTS module Direct connection of GPS Antenna via GPS Antenna Splitter R110 ›› Software adaptationsSignal input from roof antenna666_070666_029Input for Emergency Call Module Antenna (under bumper) R263 GPS antenna inputLTE antenna 1 output to J794 Emergency Call Module Antenna) R263Signal output to J533Signal output to J794GPS Antenna Splitter R110Data Bus On Board Diagnostic Interface J53344 FunctionWith the Audi connect stolen vehicle locator system, there are two scenarios if a theft is suspected:1. The owner realizes that the vehicle has been stolen. 2. The vehicle detects external manipulation.1. The owner realizes that the vehicle has been stolen. In this case, the customer must report this to the police immediately.2. The vehicle detects external manipulation. If the gateway (J533) suddenly loses its power supply (for example, if the battery is disconnected), it automatically sends data. The owner then informs the police immediately, so that the authorities can exchange data to track the vehicle.Display in myAudi after the theft report666_11145 AppendixGlossaryThis glossary explains all terms in this eSelf-Study Program which are written in italics and marked with an arrow ↗. ↗ CD (Compact Disc) An optical storage medium where data is burned onto a metal-coated plastic disc by means of a laser beam. CD-R (Compact Disc Recordable) CD which can be written to once only. CD-RW (Compact Disc Rewritable) Rewritable CD ↗ CGW (connected gateway) Internal designation for a gateway with an integrated mobile network module required to use Audi connect vehicle-related services. ↗ CI+ module (Common Interface) Is responsible for decrypting pay TV channels and can house an additional smartcard for additional pay TV channels. ↗ Composite video Video transmission standard in which all signals are transmitted via a single cable. ↗ DAB (Digital Audio Broadcasting) Digital transmission standard for the terrestrial reception of radio stations. DAB+ An advanced version of DAB, which provides more radio stations per frequency. ↗ Data transfer rate The data transfer rate is the amount of (digital) data which can be transferred in a specific unit of time. DivX A type of video compression which is used mainly to significantly compress large files at a good level of quality. DMB (Digital Multimedia Broadcasting) A digital transmission standard for the terrestrial reception of video and audio programmes. DRM (Digital Rights Management) A system to protect or be able to charge for for example, Media. One Internet example is Napster. ↗ DVB-T (Digital Video Broadcasting – Terrestrial) Digital transmission standard for terrestrial television signals. ↗ DVB-T2 (Digital Video Broadcasting – Terrestrial 2) Successor to DVB-T in Germany with which channels can be transmitted in HD quality. ↗ DVD (Digital Versatile Disc) Further development of the CD with a capacity of 4.7 GB on DVDs with single layer coating (single layer DVD±R, DVD±RW) and 8.5 GB on DVDs with double layer coating (double layer; DVD±R-DL, DVD±RW-DL)46(ID3) tag Additional information (for example, track, artist) in an MP3 file. ↗ A2DP (Advanced Audio Distribution Profile) Bluetooth profile for the transmission (streaming) of Hi-Fi audio signals via a Bluetooth channel. AAC (Advanced Audio Codec) Compression standard for audio files used for example, by online music stores (iTunes among others) or online radio stations. ↗ App (application) Application software for mobile devices ADSPC (Audi Application Desk – Service Process for Customer) Internal Audi hotline in the event of customer complaints about Audi connect (for Importer only!) AcVDM (Audi connect Verification Data Management) Audi tool to verify a user for myAudi. asf (ASF = Advanced Streaming Format) A digital audio and video format specially developed by Microsoft for streaming purposes. ASX (Advanced Stream Redirecting) Allows WMV or WMA files to be played back and combined in Windows Media Player. Aux-In (Auxiliary) Signal input to audio amplifiers to which any device with a line output can be connected. AV input (audio/video input) Signal input on video playback devices. avi (AVI = Audio Video Interleave) A video format defined by Microsoft that stores audio and video files together. AVRCP (Audio Video Remote Control Profile) Bluetooth profile to control audio and video devices. ↗ Bandwidth The bandwidth is a frequency range within signal processing which is designed to transmit speech or data. ↗ cd (candela) The “candela” unit (Latin for candle) refers to the light intensity that a light source can shine in a specific direction. A normal household candle has a light intensity of one candela. (ID3) tag Additional information (for example, track, artist) in an MP3 file. ↗ A2DP (Advanced Audio Distribution Profile) Bluetooth profile for the transmission (streaming) of Hi-Fi audio signals via a Bluetooth channel. AAC (Advanced Audio Codec) Compression standard for audio files used for example, by online music stores (iTunes among others) or online radio stations. ↗ App (application) Application software for mobile devices ADSPC (Audi Application Desk – Service Process for Customer) Internal Audi hotline in the event of customer complaints about Audi connect (for Importer only!) AcVDM (Audi connect Verification Data Management) Audi tool to verify a user for myAudi. asf (ASF = Advanced Streaming Format) A digital audio and video format specially developed by Microsoft for streaming purposes. ASX (Advanced Stream Redirecting) Allows WMV or WMA files to be played back and combined in Windows Media Player. Aux-In (Auxiliary) Signal input to audio amplifiers to which any device with a line output can be connected. AV input (audio/video input) Signal input on video playback devices. avi (AVI = Audio Video Interleave) A video format defined by Microsoft that stores audio and video files together. AVRCP (Audio Video Remote Control Profile) Bluetooth profile to control audio and video devices. ↗ Bandwidth The bandwidth is a frequency range within signal processing which is designed to transmit speech or data. ↗ cd (candela) The “candela” unit (Latin for candle) refers to the light intensity that a light source can shine in a specific direction. A normal household candle has a light intensity of one candela. ↗ CD (Compact Disc) An optical storage medium where data is burned onto a metal-coated plastic disc by means of a laser beam. CD-R (Compact Disc Recordable) CD which can be written to once only. CD-RW (Compact Disc Rewritable) Rewritable CD47↗ CGW (connected gateway) Internal designation for a gateway with an integrated mobile network module required to use Audi connect vehicle-related services. ↗ CI+ module (Common Interface) Is responsible for decrypting pay TV channels and can house an additional smartcard for additional pay TV channels. ↗ Composite video Video transmission standard in which all signals are transmitted via a single cable. ↗ DAB (Digital Audio Broadcasting) Digital transmission standard for the terrestrial reception of radio stations. DAB+ An advanced version of DAB, which provides more radio stations per frequency. ↗ Data transfer rate The data transfer rate is the amount of (digital) data which can be transferred in a specific unit of time. DivX A type of video compression which is used mainly to significantly compress large files at a good level of quality. DMB (Digital Multimedia Broadcasting) A digital transmission standard for the terrestrial reception of video and audio programmes. DRM (Digital Rights Management) A system to protect or be able to charge for for example, Media. One Internet example is Napster. ↗ DVB-T (Digital Video Broadcasting – Terrestrial) Digital transmission standard for terrestrial television signals. ↗ DVB-T2 (Digital Video Broadcasting – Terrestrial 2) Successor to DVB-T in Germany with which channels can be transmitted in HD quality. ↗ DVD (Digital Versatile Disc) Further development of the CD with a capacity of 4.7 GB on DVDs with single layer coating (single layer DVD±R, DVD±RW) and 8.5 GB on DVDs with double layer coating (double layer; DVD±R-DL, DVD±RW-DL) DVD±R DVD-R and DVD+R are DVD versions that can be written to once. DVD±RW DVD-RW and DVD+RW are DVD versions that are rewritable. EDGE (Enhanced Data Rates for GSM Evolution) Extended GSM standard for data transmission. Data transfer rates up to 220 kbit/s. exFAT (Extended File Allocation Table) File system developed specially for flash memory. FAT (File Allocation Table) File system developed by Microsoft. FAT16 is used for most types of mobile data storage devices up to a size of 2 GB. FAT32 (File Allocation Table) File system developed by Microsoft. FAT32 is used for mobile data storage devices from 2 GB to 32 GB. FLAC (Free Lossless Audio Codec) Codec designed for lossless compression of data. ↗ FM (frequency modulation) Modulation method where the base frequency is modified by the signal to be transmitted. The wavelength is within the 30 kHz to 300 kHz range. GIF (Graphics Interchange Format) Special graphics format for the compression of images with low color depth. ↗ GPS (Global Positioning System) Global satellite system to determine positions and to make time measurements for the navigation system. Gracenote A database owned by Gracenote. The database contains information about the audio CDs available on the market (such as track, artist, genre, playing time). ↗ GSM (Global System for Mobile Communications) An international digital mobile network standard which is used mainly for telephony but also for data transmission and text messaging. ↗ HFP (Hands Free Profile) Bluetooth profile which allows mobile phones to be connected to the vehicle’s handsfree system. ↗ HEVC or H.265 (High Efficiency Video Coding) Standard for compressing video files. Also designated as MPEG-5. It is the successor to MPEG-4 and is used in Germany, for example, for DVB-T2 (HD video). It halves the amount of data needed compared to MPEG-4. HSDPA (High Speed Downlink Packet Access) Extended UMTS standard which allows data transfer rates of up to 7.2 Mbit/s. HSDPA+ Extended version of HSDPA with possible data transfer rates of up to 42.2 Mbit/s. HSP (Headset Profile) Bluetooth profile which allows communication with a headset. IMEI (International Mobile Station Equipment Identity) The IMEI is a unique 15-digit serial number with which any GSM or UMTS device can be positively identified. JPEG (Joint Photographic Expert Group) Special image data format used for image data compression.↗ LTE (Long Term Evolution) As of 2017, the new mobile network standard. It transfers data five to six times faster than the UMTS network. Transfer rates of up to 500 Mbit/s make it possible to use infotainment functions requiring large amounts of data (for example, HD television or videoconferencing) on the move. ↗ LVDS (Low Voltage Differential Signalling) Data transfer standard where signals are sent via two cables at a low voltage. M3U An open playlist file format which is used for the storage of playlists. m4a (MPEG-4 audio) MPEG-4 file for audio content m4b (MPEG-4 audiobook) MPEG-4 file for audiobooks m4v (MPEG-4 video) MPEG-4 file for video content MAP (Message Access Profile) Bluetooth profile which allows text messages and e-mails to be displayed. ↗ MIB (modular infotainment matrix) Designation for a building block system for infotainment components used by several brands and on various models. MMC (Multi Media Card) Digital memory card ↗ MPEG (Moving Pictures Expert Group) Group of experts focused on the standardization of video compression techniques. MPEG-1/-2 Layer 3 File format for the compression of audio files with minimal loss of sound quality. The standard file ending is ".mp3". ↗ MPEG-2/-4 MPEG 2/4 formats are designed for video and audio compression and are used, among other things, for DVDs (MPEG-2) and mobile phones (MPEG-4). MPEG-4 or H.264 (AVC) Standard for highly efficient video compression, which can be used for a number of applications including HDTV, digicams or portable video (for example, mobile phones, iPod). Multi SIM Designates SIM cards which use the same contract and the same telephone number. In Germany for example, this allows up to three devices (for example, mobile phone + Audi connect + laptop) to be operated simultaneously with a single telephone number. ↗ MW (medium wave) Electromagnetic waves, where the signal to be transmitted has the effect of changing the amplitude of the waves48 (amplitude modulation). The wavelength is within the 300 kHz to 3000 kHz range. ↗ NFC (Near Field Communication) Standard for wireless data transfer where the two devices communicating must be very near to each other. NTFS (New Technology File System) File system developed by Microsoft. OCU (Online Connectivity Unit) Internal Audi designation for emergency call module control unit and communication unit J949. Ogg (also known as Ogg Vorbis) File format for multimedia files. ↗ OLED (organic light emitting diode) OLEDs emit light from organic semiconductor layers that are less than 1 µm thick. OPP (Object Push Profile) Bluetooth profile for sending individual files (for example, business cards or images). PAL (Phase Alternation Line) Standard for the analog transmission of color television. The red color difference signal of every second image line is shifted in phase through 180° relative to the preceding image line. This means that transmission errors are less visible to the observer. PBAP (Phone Book Access Profile) Bluetooth profile which allows the transmission of telephone and address entries. PIN (Personal Identification Number) A numeric code required for connecting mobile phones and thus for enabling access to the mobile phone’s data. Secret multi-digit code with which a user can authenticate him/herself for a system, application or machine. PLS (playlists) A file format which is used for the storage of playlists. PNG (Portable Network Graphics) A special graphic format developed for lossless compression. Podcast (portmanteau of "iPod" and "broadcast") A podcast is a media file which can be downloaded from the Internet (audio or video) and also be subscribed to. ↗ PR number Number with which the individual equipment on a vehicle can be identified. RDS (Radio Data System) Transmits additional information via the radio signal. RSS (Rich Site Summary