TECHNICAL DOCUMENTATION

SSP 990493 – The 2019 Audi A8 Introduction

PDFEN106 pages11 MB
SSP 990493 – The 2019 Audi A8 Introduction - PDF cover

This PDF is currently unavailable.

Read document text
The 2019 Audi A8 IntroductioneSelf-Study Program 990493 Audi of America, LLC Service Training Created in the U.S.A. Created 05/2018 Course Number 990493 ©2018 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Revision:1-June_2018ii IntroductionOverview Dimensions12 4BodyIntroduction Attachments Interior equipment Roof66 10 12 17EnginePowertrain Fuel tank Exhaust system for the 3.0l TFSI engine1819 20 22Power transmissionOverview Automatic transmission selector mechanism Parking lock emergency release 8-speed automatic transmission 0D5 Functions influencing the transmission and sport differential2626 28 29 30 37SuspensionOverview Axles and wheel alignment Adaptive air suspension Steering system Suspension Wheels and tires4040 41 42 43 44 45Electrics and electronicsInstallation locations of the control modules4647Climate controlNew features4849Safety and driver assistance systemsPassive safety Active safety Driver assistance systems5050 68 92Infotainment and Audi connectOverview of versions9696Inspection and maintenanceOverview Special tools and workshop equipment9898 99AppendixeSelf-Study Program100100Knowledge assessment101iii This eSSP contains video links which you can use to access interactive media.The eSelf-Study Program (eSSP) teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. For further information about maintenance and repair work, always refer to the current technical literature.NoteReferenceiv IntroductionLaunched in Europe in 1994, the Audi A8 was the world’s first large volume production automobile with a self-supporting aluminum body. Since then, Audi has built approximately one million vehicles with the Audi Space Frame body. Its successor continues this tradition. The design of the 2019 A8 embodies the fundamental qualities for which Audi is renowned: sports appeal, lightweight construction and quattro all wheel drive. Stylistically, the new A8 marks the beginning of a new design era for the entire brand. The front end, with its wide, upright single frame grille and fluid muscular body symbolizes sporty elegance, sophistication and progressiveness. The defining design feature of the new A8 is spacious luxury. The interior resembles a lounge of generous proportions. The interior is deliberately minimalist with clearly defined and strictly horizontal architecture. Audi carries its high quality standards into the digital age with a radically new operating concept. The driver operates the infotainment system by fingertip control on a large display. A second touchscreen display in the center tunnel console is used to access the climate control and comfort functions as well as making text inputs. The 2019 A8 employees the MHEV (Mild Hybrid Electrical Vehicle) technology based on a newly developed 48 volt electrical system. The 12 volt system of the A8 is a sub-system of the 48 volt system.662_002Learning objectives of this eSelf-Study Program: This eSelf-Study Program describes the design and function of the 2019 Audi A8. When completed, you will be able to answer questions about the following topics: ›› ›› ›› ›› 48 volt electrical system. New suspension features. New power transmission features. New features of the assistance systems.1 OverviewEngines3.0l V6 TFSI engine with twin-scroll turbocharger ›› Maximum power: 335 hp (250 kW) ›› Maximum torque: 369 lb ft (500 Nm) ›› 0-60 5.7 seconds The 2019 A8 is the first Audi to be offered as a mild hybrid.Click here for additional information about hybrid vehicles.Displays and operationA new operating and display concept incorporating MMI touch response technology with two touchscreens, a switch panel (optional) and an illuminated button module with tactile and audible feedback, intelligent handwriting entry with whole-word and multifinger recognition. An Audi virtual cockpit with HD resolution and optional head-up display.Driver assistance systemsFor the first time in an Audi, a central driver assistance control module (zFAS) utilizes the data from various sensors to comprehensively map the area around the vehicle. This map is updated continuously and is used by a number of assistance functions including the newly optional adaptive cruise assist. Adaptive cruise assist combines the three formerly independent systems of adaptive cruise control, Audi active lane assist with “early” corrective steering point, and traffic jam assist. Intersection assist helps the driver in situations where cross-traffic ahead of the vehicle can only be seen late due to impaired visibility.SuspensionThe front and rear axles have a precision five-link construction (dynamic allwheel-drive steering is optional). The sport differential will be available in the future only for the S8. The adaptive air suspension has hydraulically controlled dampers which are adjustable to four height levels. A fully active Audi AI active suspension will be available at a later date. It controls each wheel separately and allows a wide range between comfort and sportiness.2 Climate controlThe climate control system uses R-1234yf as a refrigerant. In the future, Carbon dioxide (CO2) will be used as a refrigerant. It is referred to commercially as R744. It contains neither fluorine nor chlorine and is produced in a series of natural processes that reduce the possibility of depleting the earth’s ozone layer.BodyThe body of the Audi A8 follows the Audi Space Frame (ASF) principle. It is assembled from aluminum parts – the classic composite of cast nodal joints, extruded profiles and sheet metal. The occupant cell is made from hotformed steel components, complemented by an ultra-high-strength, torsionally rigid rear bulkhead made from carbon-fiber composite (CFC). A magnesium dome strut completes the lightweight construction concept.662_068Power transmissionThe eight-speed 0D5 transmission has been redesigned for the A8. The rear final drive 0G2 is used on the rear axle. The quattro with sport differential drive system with the 0D3 final differential will only be used on the S8.Electrical systemThe MHEV technology of Audi is based on the newly developed 48 volt electrical system – it supplies the 12 volt electrical system, which in this case is the electrical subsystem. The 48-volt electrical system is powered by a belt alternator starter (BAS) which is connected to the engine serpentine drive. A lithium-ion battery, positioned safely under the luggage compartment floor, serves as an energy storage device.3 Dimensions58.5 in (1488 mm)41.2 in(1049 mm)64.7 in (1644 mm) 76.5 in (1945 mm)662_07364.2 in (1633 mm) 83.8 in (2130 mm)662_074mm 1 ) )51(104 in41.39.2 in(995mm)38.9 in (989 mm)123.1 in (3128 mm) 208.7 in (5302 mm)46.6 in (1185 mm)662_075427.4 in (697 mm) 62.2 in (1581 mm)2)61.1 in (1553 mm)2)59.1 in (1502 mm)3)57.5 in (1462 mm)3)33 in (840 mm)45.6 in (1159 mm)662_076Exterior dimensions and weightsLength Width (not including exterior mirrors) Width (including exterior mirrors) Height Front track width Rear track width Wheelbase Unladen weight 208.7 in (5302 mm) 76.5 in (1945 mm) 83.8 in (2130 mm) 58.5 in (1473 mm) 64.7 in (1644 mm) 64.3 in (1633 mm) 123.1 in (3128 mm) 4287.9 lb (1945 kg)Inner dimensions and other specificationsFront cabin width Front shoulder width Rear cabin width Rear shoulder width Load sill height Luggage compartment capacity Drag coefficient cw Capacity of fuel tank 62.2 in (1581 mm)2) 59.1 in (1502 mm)3) 61.1 in (1553 mm)2) 57.5 in (1462 mm)3) 27.4 in (697 mm) 17.8 cu ft (505 l) 0.27 Cw 21.7 gal (82.1 l)Maximum headroom Elbow room width 3) Shoulder room width1) 2)All dimensions refer to the unladen weight of the vehicle.5 BodyIntroductionThe new Audi A8 is based on an advanced ASF body structure. With a mix of aluminum, steel, magnesium and carbon fiber reinforced polymer (CFRP), the load-bearing structure combines four different lightweight materials. However, the largest proportion (58%) is represented by aluminum components which, as cast nodal plates, extruded sections and sheet metal panels, are the characteristic elements of the ASF construction concept. A rear bulkhead made of carbon fiber saves approximately 50% of the weight compared with its predecessor and helps make the body rigid and strong in addition to being lightweight. The intelligent material mix is completed by a dome strut which is 28% lighter and made of magnesium. Torsional rigidity has been increased 24% compared to the previous A8.Key:Sheet aluminum Die-cast aluminum Aluminum section Ultra-high-strength steel (hot-stamped) Carbon fiber reinforced polymer (CFRP) Magnesium Advanced high-strength steel High-strength steel Soft steelNote The image shows an Audi A8 with a standard wheelbase. The body of the long-wheelbase version (A8 L) is 5.12 in (130 mm) longer in the area of the ‘B’ pillar.6 Joining techniquesThe following connection systems are used when assembling the multi-material body: ›› Resistance spot welds on steel. ›› Resistance spot welds on aluminum. ›› MAG welds. ›› Laser welds on aluminum. ›› MIG welds. ›› Friction element welds. ›› Semi-tubular punch rivets. ›› Pop rivets. ›› Flow drill screws. ›› Clinch connections. ›› Seaming. ›› Bonding.662_1927 Safety cellThe occupant cell, also called the safety cell, is made of aluminum and conventional hot-formed steel. The cell is comprised of the lower area of the end wall, the side sills, the B-pillars and the front area of the roof arch. Some of these sheet metal blanks are produced with different thicknesses (tailored blanks) and are also partially tempered where necessary. This reduces the weight and increases the strength in extremely safety-critical areas.662_193B-pillarsThe B-pillars are specially formed to enhance rigidity and meet crash requirements. They are produced using tailor rolled blank technology. These are flexibly rolled blanks, where variations in sheet-metal thickness are produced by controlled opening and closing of the gap between the rollers. These variations in sheet-metal thickness not only save weight, but also create defined crumple zones which provide protection in the event of a side impact. The sheet metal thicknesses vary between 0.06 and 0.08 in (1.5 and 2.0 mm). Partial tempering: The individual zones of the B-pillar are cooled in the mold at different rates during hot working, giving them different strength characteristics. During a side impact, the bottom section of the B-pillar deforms in order to absorb energy. However, less deformation takes place in the upper section of the B-pillar (at head height).0.07 in (1.7 mm)Ultra-high-strength 0.08 in (2.0 mm)0.07 in (1.7 mm)High-strength0.06 in (1.5 mm)662_194662_1958 Roll hemmingRoll hemming is used all around for the entire front and rear door sills. This process increases the door opening area (better ingress and egress for the occupants) and improves the field of vision in the A-pillar area. Roll hemming is complemented by grip punch riveting which fixes the side wall frame in its position. This is in addition to all around structural bonding. These joining techniques allow the aluminum side wall frame to be mated with the hot-worked, ultra high strength sheet steel of the B-pillar, roof arch and sill with narrow flanges.Roll hemmingGrip punch rivet662_198662_197B-pillarCarbon fiber rear bulkheadAn ultra high strength, torsion-resistant rear bulkhead made of carbon fiber is the largest component of the occupant cell and accounts for 33 per cent of the torsional rigidity of the overall vehicle. To fully absorb the loads in the longitudinal or transverse direction and shear forces, 6 to 19 fiber layers are placed on top of one another for load optimization. These individual fiber layers are composed of 1.96 in (50 mm) wide bands which can be positioned individually at any fiber angle and with a minimum cut to create a finished layer. The carbon fiber rear bulkhead, which contains all attachment points for components such as the loudspeakers, the rear sunshade, the three-point safety belts and the rear center armrest, is inserted into the body through the rear window cutout during final assembly. It is connected to the body structure using two-component strength adhesive and rivets. The two-component adhesive prevents contact corrosion.Load application direction662_1969 AttachmentsFully electric door lockAnother new feature of the A8 is the actuation of the door locks. An “e-lock” is used in which an opening signal is transmitted electrically from the door inner handle or door outer handle to the door control module via a microswitch. The door control module in turn controls an electric motor which releases the rotary latch, opening the lock. The microswitch for the door outer handle is located in the support arm. It moves after a few millimeters of pressure on the door handle. The door control module triggers the electric motor in the “e-lock” and the door can be unlocked with very little effort.Driver Side Exterior Door Handle Switch F546 Front Passenger Exterior Door Handle Switch F547 Driver Side Rear Exterior Door Handle Switch F548 Passenger Side Rear Exterior Door Handle Switch F549662_103Door handle, support arm and door lock in the rest state.Emergency release mechanismNormal exterior door operation via the microswitch.662_104To open the doors in the event of an electrical malfunction, two Bowden cables are used; one from the interior door handle and one from the exterior door handle. To open the door from the interior, the interior door handle must be pulled far beyond the normal “e-lock” opening angle. Opening the door with the exterior door handle can only be done after the lock cylinder or interior door handle have been actuated. The exterior door handle can then be pulled further than the normal actuation angle and with more force.662_105662_106Interior door operation via a Bowden cableExterior door operation via a Bowden cable10 Door opening via the microswitchThe microswitch for opening the door is located in the interior door handle. When the door control module detects the switch being opened, it triggers the servo motor in the door lock.662_107Interior door handle in the rest state Driver Side Interior Door Handle Switch F550 Front Passenger Side Interior Door Handle Switch F551 Driver Side Rear Interior Door Handle Switch F552 Passenger Side Rear Interior Door Handle Switch F553662_108Normal exterior door operation via the microswitchIn certain situations, for example, when another vehicle is detected within the danger zone by the exit warning system, the “e-lock” can delay the opening of the door and issue both a visual and tactile warning for a short period of time.Power latchingThe 2019 A8 can be equipped with an optional power latching system. The drive units for this system are different from previous versions. The Door Closing Aid Motors (V302, V303, V541 and V542) exert a pull via an integrated linear drive which moves the rotary latch in the door lock to the end position.Note Before disconnecting the 12 Volt battery, make sure that one door window is open or that the ignition key is not inside the vehicle or in the luggage compartment.Reference You can find further information on the electric door lock in eSelf-Study Program 970293, The 2019 Audi A8 Electrics and Electronics.11 Interior equipmentInstrument panelThe upper trims for the instrument panel can be ordered with various wood inlays that form the wrap-around – the large arc that runs above the door trim panels as far as the rear. This area contains the air vents which are covered by these trims when not in use. When air from the climate control system flows directly into the interior, the shutters glide away upwards electrically while the air outlets move out towards the driver and the front passenger.662_109Design Situated to the right and left of the central 10.1" touchscreen and around the light switch, covers with the same black panel appearance as the display create an uninterrupted uniform look. The transition between this level and the level of the air vents is in turn covered on the right and left by a trim strip.Instrument panel ventUpper trim for instrument panelTrim stripCover in black panel design Instrument panel vent Upper trim for instrument panel Trim strip Cover in black panel design 10.1" touchscreen, display unit for front information display and Front Information Display Control Head J685662_11012 Front center console:The black panel appearance of the instrument panel is continued to the center console. The transition is made through a second, 8.6" touchscreen with an operator control module at the bottom.662_1118.6" touchscreen, display unit 2 for Front Information Display Control Head 2 J1060Switch Module in Instrument Panel Center EX22 Center Console Switch Module 1 EX23Selector mechanism662_11213 Rear center consoleThe standard rear seat configuration of the A8 is a threeseat system. A load-through hatch is also available. An individual rear seat system without a non-folding, continuous center console is optional. The console can be ordered with USB ports, phone box (with wireless charging) and SD card readers. Irrespective of whether the long, continuous center console or the folding center armrest is installed in the rear backrest, the A8 can be equipped with the Rear Seat Remote operating concept. The Rear Seat Remote unit with its 5.7" OLED display is similar in size to a smartphone and is housed in the center armrest and can be removed. The Rear Seat Remote can be used to set convenience and infotainment functions in the rear. Another option is heated armrests in the center armrests at the front and rear, and in the doors.662_113Mounting and charging cradle for Smart Remote ControlWireless Control Head 1 E859Folding tablesButtons for seat adjustmentAudi phone box662_114Reference You can find further information on the Rear Seat Remote unit in eSelf-Study Programs 990293, The 2019 Audi A8 Infotainment and Audi Connect Systems and 980193, The 2019 Audi A8 Climate Control Systems.14 SeatsThe seats of the 2019 A8 are a new design. The front seats are approximately 8.8 lb (4.0 kg) lighter than in the predecessor model. They are constructed using glass fiber reinforced plastic (GFRP).Front seats The front seats are available in several designs. The top version is the comfort individual contour seat (PR no. Q2J). In addition to pneumatic seat and backrest bolster adjustment, it also features optional heating and ventilation, each separately controllable in three stages. The optional massage functions have also been extended. Every backrest contains 16 small bubble-shaped air pockets. They massage the entire back. For this purpose, there is a choice of seven programs and three levels of intensity. A small compressor for each seat delivers up to 7.25 psi (0.5 bar) pressure.Individual contour seat (PR no. Q2J)662_115Valve Block 2 in Driver Seat N476Massage matDriver Multi-Contour Seat Compressor V439Backrest bolster adjustmentValve Block 1 in Driver Seat N475Air cushion for lumbar supportSeat bolster adjustment662_11615 Rear seat With the rear three seat system, the outer seats can be heated as an option. The longitudinal position and the seat and backrest angle can also be adjusted electrically. The lumbar support can then be adjusted pneumatically. If desired, a massage function is also available with 18 triple air pockets per seat. The individual seat system features the same adjustment options as those in the rear three seat system.Reclining seat Reclining rear seats are optional on the 2019 A8 in the Executive package. The rear passengers can move a seat to a reclined position and place their feet on an electrically folding area on the backrest of the special passenger seat. If required, the feet are warmed and massaged there in several stages. Three intensities, two programs and three foot sizes are available. The entire foot reflex zones are also stimulated. The rear passengers can lean their head on the soft comfort head restraints in the new Kokon leather version whose height here can be adjusted electrically. The reclining seat package features the comfort individual contour seats with ventilation and massage, the long center console with a double folding table, the Rear Seat Remote operating unit, rear seat entertainment and four-zone deluxe climate control.662_117Foot massageRear Seat RemoteMassage, back areaMassage, shoulder area16 RoofPanoramic sunroofThe A8 has a two-piece glass roof. The front glass panel is movable while the rear glass panel is fixed. Since drainage is possible via the front windshield and rear window, no drain hoses are fitted here. A glass cover is securely mounted in front of the movable panel.662_11917 EngineTorque/power curve of 3.0l TFSI engine EA839 Engine with code CZSE590.0 (800) 469.3 (350) 663.8 (900) 536.4 (400)   Power output in hp (kW)   Torque in lb ft (Nm)516.2 (700)402.3 (300)442.5 (600)335.2 (250)368.7 (500)268.2 (200)295.0 (400)201.1 (150)221.2 (300)134.1 (100)147.4 (200)67.0 (50)Engine speed [rpm]662_087Features Engine code Type Displacement Stroke Bore Number of valves per cylinder Firing order Compression ratio Power output at rpm Torque at rpm Fuel type Turbocharging Engine management Maximum injection pressure Lambda/knock control Mixture formation Exhaust gas treatment Emission standard ConceptSpecifications CZSE V6 engine with 90° V angle 182.7 cu in (2995 cc) 3.50 in (89.0 mm) 3.32 in (84.5 mm) 4 1-4-3-6-2-5 11.2 : 1 335 hp (250 kW) at 5000 - 6400 369 lb ft (500 Nm) 1370 - 450 Premium Twin scroll exhaust turbocharger with wastegate Bosch MDG 1 3625.9 psi (250 bar) Adaptive lambda control, adaptive knock control Direct injection 2 close-coupled ceramic catalytic converters Oxygen sensor before and after catalytic converter LEV3 / Tier3 Mild hybrid 48VReference For further information about the 3.0L V6 TFSI Engine, please refer to eSelf-Study Program 920173, The Audi 3.0l V6 TFSI EA839 Engine.18 Powertrain3.0l TFSI engine (CZSE) 335 hp8-speed automatic transmission 0D5 AL552-8QRear axle drive 0G2 - standard differential HL195.S3 M PR no.:1) GH1Rear axle drive 0D3 - sport differential HL195.T2 M PR no.:2) GH2 (Future) S8 onlyKey to new manufacturer code designationFor example: 8-speed automatic transmissionAL552-8QAutomatic planetary gear setLongitudinal mountingDevelopment number (indicating torque capacity, generation and position of front final drive)Number of speedsDrive system (all-wheel drive with integrated transfer case/center differential)For example: Rear axle driveHL195.S3 MrearLongitudinal mountingRing gear diameter in mmS = Standard (non-locking differential) T = Torque Vectoring (sport differential)1st generation 2nd generation 3rd generationManufacturer code: M = Magna powertrain Z = ZF Friedrichshafen AG1) 2)Production number GH1: Real axle differential (non-locking differential) Production number GH2: Rear axle differential torque vectoring19 Fuel tankThe 2019 A8 has a 21.7 gal (82.1 l) fuel tank. A rollover valve with a pressure retaining valve is installed in the tank and a refueling shut-off valve is installed in the liquid trap. A rollover valve is installed at the bottom of the tank. The end of the valve line is found at the top in the liquid trap and also on the immersion tube.Level sensor in the top chamber Roll-over vent valveFiller neckVent line662_064Non-return flapBaffleSwirl pot with integrated fuel filter in the delivery module (long life) in the tank20 Rollover valve with pressure retaining valve Immersion tubeRefueling shut-off valveLiquid trap with short refuelling shut-off valve in 21.7 gal (82 l) fuel tank662_059Vent lineBaffle Line for suction jet pump Mixer tube on the transfer side Level sensor in the secondary chamber Intake for suction jet pumpLevel sensor in the main chamberFuel return line Fuel supply line662_057_alt21 Exhaust system for the 3.0l TFSI engineThe gas flow paths are very short because the turbocharger module is located in the inner V of the engine. The catalytic converter is bolted directly to the exhaust turbocharger outlet. This allows the catalytic converter to reach its optimal operating temperature very quickly after a cold start.Main catalytic converterSecondary catalytic converterCatalytic converter module The module is flanged-mounted directly to the exhaust turbocharger, which houses the main and secondary catalytic converters. Both catalytic converters are ceramic-type converters.Center muffler (operates on the absorption principle)Decoupling elementFront muffler (operates on the absorption principle)22 Exhaust Door Control Unit J883Exhaust Door Control Unit 2 J945Exhaust flaps Two of the four exhaust outlets can be closed, reducing noise as the vehicle accelerates from a stop.662_077Rear muffler (operates on the reflection and absorption principle)Note The exhaust flap is actuated by the exhaust flap control unit via a worm gear. Because this is a "self-locking" gear, it is essential that the servomotor be removed before testing the movement of the flap.23 Engine mountsFive-point engine/transmission mounts are installed on the 3.0l TFSI engine. They are hydraulically switchable mounts. The engine and side transmission mounts have two operating states. They are soft at idle and switch to hard when drivingTransmission mountRight Electrohydraulic Engine Mount Solenoid Valve N145Transmission Mount Valve 1 N262Left Electrohydraulic Engine Mount Solenoid Valve N144Transmission Mount Valve 2 N263662_086Right Electrohydraulic Engine Mount Solenoid Valve N145662_121Hydraulic engine mount24 Hydraulically switchable transmission mounting The hydraulically switchable transmission mounts, Transmission Mount Valve 1 and 2 (N262, N263) are laterally mounted to the transmission to counteract the torsional vibration of the engine and transmission unit.662_229Transmission Mount Valve 2 N263Conventional transmission mounting The conventional transmission mount is installed in the rear section of the transmission and counteracts the load reversal and tilt functions.662_23025 Power transmissionOverviewThe 8-speed automatic transmission and drive concept are already in use on 2017 Audi Q7. (eSelf-Study Program 990163, The 2017 Audi Q7 Introduction.) The transmission has now been adapted to the Audi A8 and further enhanced. Refer to page 30 for more information. The selector mechanism transmits the driver's operating requirements through shift-by-wire technology. Refer to page 28 for more information. The parking lock emergency release mechanism is similar to the Audi Q7 and has been adapted for the Audi A8. Refer to page 29 for more information.8-speed automatic transmission 0D5Coolant returnSelector mechanism3.0l TFSI engine CZSECoolant lineTransmission Fluid Cooling Valve N509The TFSI engine and OD5 transmission are supported by a five-point hydraulic mounting system with 4 switchable mounts. It is controlled by Engine Control Module J623.Parking lock emergency releaseATF temperature regulation ATF temperature regulation is controlled via valve N509 and is explained on page 35.26 Rear axle The rear axle drive is mounted to the sub-frame by a fourpoint mounting system. The radial rubber metal bearings, except the additional bearing, must be mounted in a specified installation position described in the workshop manual.Rear axle drive 0G2 Non-locking differential Rear axle drive 0D3 Sport differential (optional for S8 only) Sport differential The sport differential 0D3 is a further development and a new generation of the sport differential 0BF (2nd generation). In this second generation two control modules are responsible for activating the sport differential. Drivetrain Control Module J775 sends a signal for the calculated redistribution of torque between the rear wheels to Differential Lock Control Module J187 via the FlexRay bus. The differential lock control module activates the sport differential actuators and initiates the redistribution of torque. The sport differential set-up can be influenced using the Audi drive select modes. Refer to page 37. The ATF and the axle oil of the sport differential are not subject to routine maintenance. For more information about the second generation "quattro with sport differential", refer to eSelf-Study Program 950273, Audi quattro with ultra technology. New: For the first time, the driver can now see a graphic display of the distribution of the drive torque to the individual wheels in the MMI. The menu items "Vehicle" "Show vehicle" "quattro" must be selected in the MMI menu. The arrows shown on the wheels show the distribution of drive torque.Propeller shaft Rear axle drive 0G2Vehicle · quattro662_045OD3662_227Rubber-metal bushing Additional bushing Rubber-metal bushing662_1301)Differential Lock Control Module J187 can be  accessed via Address Word 0032.27 Automatic transmission selector mechanismThe Audi A8 also now uses the current selector mechanism and operating concept. Only the design has been adapted to the interior of the Audi A8.Selector Lever Release Button E681Selector leverParking Lock Button E816 with Parking Lock Indicator Lamp K320Selector Lever Transmission Range Display Y5662_132Selector Lever E313 (houses Selector Lever Sensor System Control Module J587)1)Connection between selector lever and vehicleConnection to selector lever position display1)J587 communicates over the instrument cluster CAN bus. J533 (gateway) and the FlexRay data bus system are used for communicating  with the Transmission Control Module.28 Parking lock emergency releaseThe parking lock emergency release is similar to the 2017 Q7. The actuating mechanism is located under a cover in the driver's footwell. Emergency-releasing the parking lock (P-OFF position) ›› Remove cover. ›› Insert the socket wrench into the actuating mechanism, position 1. ›› Turn the socket wrench clockwise 140°, position 2, and press down simultaneously, position 3. When the parking lock emergency release device is actuated, the yellow transmission warning lamp and the drive position indicator N light up in the instrument cluster. The following warning also appears: "Vehicle may roll away! P cannot be selected. Please apply parking brake." Warning! Before actuating the emergency release device of the parking lock, the vehicle must be secured to prevent it from rolling away. If it is no longer necessary to emergency-release the parking lock, the parking lock must be locked again (P-ON position). It is necessary to check the emergency release device after assembly work on its component parts.Locking the parking lock (P-ON position) Pull the parking lock emergency release device slowly upwards out of the actuating mechanism, position 4. If the device is removed quickly, it could damage the release mechanism. ›› Fit the cover.3 2Cover Socket wrench Approximately 140°1662_135Actuating mechanism662_1344Step 4 is used to restore shift function. After lifting the handle, it will rotate counter-clockwise 140 degrees to be reset.662_13629 8-speed automatic transmission 0D5The 0D5 transmission made its debut in 2017 in the Audi A7. At Audi the 0D5 has the internal factory designation AL552-8Q. The manufacturer, ZF-Getriebe GmbH, uses the designation 8HP65A. The 0D5 transmission is rated for peak input torque of 516.2 lb ft (700 Nm). The transmission operating characteristics can be adjusted via Audi drive select. Refer to page 37. The following aspects of the 0D5 transmission as used in the A8 are new: ›› The MTF pump in the transfer case, previously driven by the side shaft, is no longer required. ›› The bearing for the drive pinion of the front drive has been optimized for friction by double row angular contact ball bearings. ›› The front differential is lubricated by a new low-viscosity axle oil. ›› The hydraulic impulse storage system, HIS for short, is replaced by Transmission Fluid Auxiliary Hydraulic Pump 1 V475. The auxiliary hydraulic pump provides a constant supply of ATF, assists the start-stop function and allows the TFSI engine to be shut off under coasting in certain situations.Double shaft seal, planetary gearbox/transfer box1)Transfer case ventSelf-locking center differentialMTF filler and inspection plug for the transfer caseSide shaftOil ring1)If the double shaft seal between the planetary gearbox/transfer case is leaking, either ATF or MTF will leak from the drainage port. Refer  to fig. 662_139, page 32 .30 Torque Converter with dual-mass vibration dampening platePlanetary gear set Front differentialDouble row angular contact ball bearingsDouble shaft seal, transfer case/ front axle driveInspection and filler plug for front axle driveATF filler and inspection plugLeak oil drainage port for the double shaft seal, transfer case/front axle drive (visible from below, see page 34)ATF pan made of plastic with integrated ATF filterTransmission Fluid Auxiliary Hydraulic Pump 1 V475662_13831 ATF and MTF systemsThe 0D5 transmission has three separate systems containing different types of oil:ATF system for the planetary gearbox and the hydraulic control unit (not subject to routine maintenance). MTF supply for the transfer case (gear oil containing STURACO1), not subject to routine maintenance). Oil supply for the front axle drive. The new low-viscosity axle oil is not subject to routine maintenance and must not be mixed with non-low viscosity axle oil. To avoid mixing oils, the new axle oil is dyed red.Inspection and filler plug for front axle drive ATF filler and inspection plug MTF filler and inspection plug for the transfer case662_224Oil reservoirIn transmissions without an MTF pump, the transfer case is lubricated by the gears running in the MTF sump (oil sump). The oil reservoir is filled with the gear splash oil and serves to distribute the oil.1)S  TURACO is an oil additive which protects against excessive stresses in the center differential and thus helps to enhance ride comfort.Gearbox breather The front axle drive and the ATF system are ventilated via the collecting chamber. A breather port leads from the collecting chamber into the bell housing. The transfer case is ventilated via a separate ventilation cap. When the transmission is warming up or cooling off, the pressure is equalized via the transmission vents. To allow pressure equalization to take place, the ventilation ports must be open and unobstructed.662_225ATF breather Collecting chamber Ventilation portTransfer case ventLeak oil drainage port for the gear set/transfer case double shaft sealVent for the front axle drive662_139Note During transportation and when moving and/or performing work on the transmission, the axle oil and ATF may mix via the common vent if the transmission is tilted too far. Always follow the instructions given in the repair literature.32 ATF supply and hydraulicsIn Mild Hybrid Electric Vehicles (MHEV), the 0D5 transmission is supplied ATF by two ATF pumps; one mechanically driven pump on one electric pump. Both pumps draw the ATF from the ATF intake filter. Transmission Fluid Auxiliary Hydraulic Pump 1 V475 now allows the TFSI engine to be shut off under coasting.Brake A Pump drive hub with spline, connection to torque converterMechanically driven ATF pump This ATF pump is identical to the twin stroke vane pump used in the 0BK transmission. It is powered by a chain drive via the torque converter of the TFSI engine. When the pump reaches a specified speed of approximately 500 rpm, it provides a reliable supply of ATF with the auxiliary hydraulic pump.Impeller shaftSun gear shaft S1/S2 Chain drive ATF pump, mechanically driven662_142Transmission Fluid Auxiliary Hydraulic Pump 1 V475 By assisting the mechanically driven ATF pump, V475 provides a reliable supply of ATF for the start-stop functions of the transmission. If the auxiliary hydraulic pump is unable to circulate ATF because the overload cut-out has been actuated or a fault has occurred, the start-stop functions are no longer available. If V475 is faulty, the yellow transmission warning lamp lights up.Pump electronics – integrated into housingV475 operates within an ATF temperature range of 68 257 °F (20 -125 °C) and has three output levels. It communicates with Transmission Control Module J217 via a LIN bus. The auxiliary hydraulic pump provides a reliable and quick supply of ATF. This aids disengagement of the parking lock and allows delay-free start-up. If the mechanically driven ATF pump reaches the required speed and is capable of supplying system pressure by itself, the auxiliary hydraulic pump receives a signal via LIN bus to stop circulating ATF.Ground contact for voltage supply Terminal 30, positive contact to power supply Connection, pressure sideLIN bus connectorBrushless DC motor ATF suction filter G-rotor pump with non-return valve662_14333 Mechatronic moduleThe mechatronic module of the 0D5 transmission in the Audi A8 has the factory designation E 26/29 at ZF-Getriebe GmbH. The sensors, actuators and design configuration of the electrohydraulic parking lock of the 0D5 transmission are identical to those of the mechatronic module of the 0BK transmission.Oil bleed port for double shaft oil seal, transfer case/front axle driveFiller and inspection plug for front axle drive Connection to Transmission Fluid Auxiliary Hydraulic Pump 1 V475 ATF filler and inspection plugDrain plug, front axle drivePower supply for Transmission Fluid Auxiliary Hydraulic Pump 1 V475 MTF drain plug for transfer case MTF filler and inspection plug for transfer caseElectrical connector housing for connection to vehicleMechatronic module Connection to vehicleConnectorTransmission Fluid Auxiliary Hydraulic Pump 1 V475 Connector (V475) Plastic ATF pan ATF drain plugATF filter662_226Auxiliary hydraulic pump intake portNote When performing repairs, always protect the mechatronic module against electrostatic discharge.34 ATF temperature regulationThe ATF temperature is regulated by a switchable coolant circuit which runs parallel to the large coolant circulation system of the engine. The circuit is opened or closed by Transmission Fluid Cooling Valve N509 via signals from Transmission Control Module J217 based on input from Engine Control Module J623. Engine warm-up phase (N509 closed) Valve N509 is energized, and therefore closed, during the engine warm-up phase. The ATF heat exchanger is not flooded with coolant. Since the coolant does not release any heat to the ATF, the engine reaches its operating temperature more quickly. The thermal management system of the ECM decides when valve N509 is to be opened while Transmission Control Module J217 sends the signal to actuate the valve. The criteria for opening valve N509 are the ambient temperature, the engine temperature, the ATF temperature, the engine speed and the requested heat demand of the climate control system.ATF return line ATF supply lineHeating and cooling of the ATF (N509 open) If the engine has reached its operating temperature and there is sufficient heat for every requirement, valve N509 opens. The ATF heat exchanger is flooded with warm coolant from the large engine coolant circuit. This warms the ATF and reduces its viscosity, which in turn increases the efficiency of the transmission. The ATF is heated as long as the temperature of the engine coolant exceeds that of the ATF. When the temperature of the ATF exceeds the temperature of the engine coolant, the ATF dissipates its heat to the coolant and is cooled. N509 can be tested using the VAS Scan Tool.N5092ATF heat exchanger662_1471Coolant return2 1Coolant supply Transmission Fluid Cooling Valve N509 ATF return lineATF supply lineATF heat exchanger662_148Note If the ATF cooler is leaking, coolant (glycol) could mix with the ATF. Even the smallest quantities of coolant in the ATF can have a detrimental effect on clutch control. A glycol test will detect even the smallest amounts of glycol. It can be used to confirm or rule out this as a cause of transmission shifting issues.35 Data exchange – Function diagramTransmission Control Module J217 communicates over the FlexRay data bus system. Data Bus on Board Diagnostic Interface J533 and the Instrument Cluster CAN data bus are used for communicating with Selector Lever Sensor System Control Module J587. Functional diagram of the 8-speed automatic transmission 0D5 in the Audi A8P/N signal, start enable signal to J623FlexRay, to J533 FlexRay, to J533 FlexRay, to J500 FlexRay, to J500Ground activation N509662_155G93 Transmission Fluid Temperature Sensor G182 Transmission Input Speed Sensor G195 Transmission Output Speed Sensor G510 Temperature Sensor in Control Module G747 Parking Lock Sensor J217 J500 J533 J623 Transmission Control Module Power Steering Control Module Data Bus on Board Diagnostic Interface (gateway) Engine Control ModuleKey: Ground cable Positive cable Signal line LIN bus Transmitted signal Received signal FlexRay lineN88 Solenoid Valve 1 N215 Automatic Transmission Pressure Regulating Valve 1 N216 Automatic Transmission Pressure Regulating Valve 2 N217 Automatic Transmission Pressure Regulating Valve 3 N218 Automatic Transmission Pressure Regulating Valve 4 N233 Automatic Transmission Pressure Regulating Valve 5 N371 Automatic Transmission Pressure Regulating Valve 6 N433 Sub-Transmission 1 Valve 1 N486 Parking Lock Solenoid N509 Transmission Fluid Cooling Valve V475 Transmission Fluid Auxiliary Hydraulic Pump 136 Functions influencing the transmission and sport differentialAudi drive selectAudi drive select can be used to choose between different vehicle driving modes. The following Audi drive select modes can be selected by pressing the Audi drive select button or via the MMI.662_156comfort modeTransmission: The TCM behaves in the same way as in auto mode. Sport differential: The set-up for the sport differential is moderate, steering behavior is not adjusted for faster response.auto modeTransmission: The shift points in selector positions D and S are selected according to the driver type recognition characteristics. For this purpose, the system evaluates the way in which the vehicle is being driven. The system factors in the way in which the brake and accelerator pedals are applied as well as the transverse and longitudinal acceleration of the vehicle within defined periods. Accordingly, an economical driving style leads to early upshifts and late downshifts. A sporty driving style is made possible by late upshifts and early downshifts. The driving phases in which the driver adopts an efficient, economical, sporty or manual driving style can be accessed using the VAS Scan Tool. Selector position D: The shift points are selected in a comfort-oriented way after taking account of the determined driver type. Selector position S1): In selector position S the TCM runs in sport mode. The shift points are selected in the sport mode after taking account of the ascertained driver type and are adapted to the performance range of the engine. The shift times vary from normal, with barely perceptible gear shifts, to short, with noticeable gear shifts. If the vehicle is equipped with an efficiency assist system, the driver does not receive any information in sport mode via the symbols of the efficiency assist system. Sport differential: The set-up for the sport differential is balanced. The adjustment to steering behavior ensures neutral handling. The vehicle is stabilized if a pronounced oversteer is detected.dynamic modeTransmission: If dynamic mode is selected, the TCM activates the sport program (selector position S). In dynamic mode the selector positon D can be selected at any time. If selector position D is activated before shutting off the engine, selector position (D) is again activated when the engine is subsequently started1). If the driver wants to have selector position S, he must select this. Sport differential: The torque redistribution set-up provides for highly responsive steering with a slight tendency to ovesteer. Only in the event of pronounced oversteer is the torque redistributed to stabilize the vehicle on the rear axle.individual modeThe menu item “Drivetrain” encompasses the engine, the transmission and the sport differential. The driver can select from efficient, balanced and sporty options under this menu item. These following drive select modes are assigned to these options: ›› Balanced, equivalent to the auto mode of Audi Drive select. ›› Sporty, equivalent to the dynamic mode of Audi Drive select.1)The vehicle is always restarted in the combination of Audi drive select mode auto and selector position D. 37 Start-stop systemThe start-stop system is activated automatically whenever the ignition is switched on. It helps to save fuel and reduce C02 emissions. If the requirements for start-stop operation have been met, the engine is shut off automatically when the brake is applied as the vehicle rolls to a stop. One of these conditions is that the selector lever is not in position R. The engine is automatically restarted when required. The requirements for this are a very short start time and quick readíness for drive-away. In the Audi A8 with MHEV equipment, quick readiness for drive-away is ensured by Transmission Fluid Auxiliary Hydraulic Pump 1 V475. If the auxiliary hydraulic pump is unable to circulate ATF because the overload cut-out has actuated or a fault has occurred, the start-stop function is deactivated and is no longer available. System inactive (switched off) conditions: ›› Uphill or downhill gradient: 10%1). ›› Max. speed: ›› 105.6 mph (170 km/h)1). ›› ESC is deactivated. ›› Selector position S is selected. ›› tiptronic mode is activated via the tiptronic gate or by selecting Tip- with the tiptronic paddle on the steering wheel. ›› No ATF circulation by Transmission Fluid Auxiliary Hydraulic Pump 1 V475 due to overload protection function or fault.Reference The shift schematic of the 0D5 transmission is identical to that of the 0BK and 0BL transmissions, refer to eSelf-Study Program 950103, The 2011 Audi A8 Driver Assistance.38 Neutral idle control (NIC)The neutral idle control system disengages the engine from the transmission when stopping or when the vehicle is stationary. Engine idle torque can be reduced to a minimum because the engine does not have to counteract the converter torque. This helps save fuel and reduces C02 emissions. In addition, the engine runs more smoothly and quietly at low idle torque. For this reason, the neutral idle control system is activated as often as possible (see conditions for switching on and off). Switch-on conditions: ›› Full adaption of the shift elements (brakes, clutches). ›› ATF temperature  approximately 68 °F (20 C°)1). ›› Gradient  4%1) (the gradient is determined by the longitudinal acceleration sensor of the ABS system). ›› Selector position D or R . ›› Accelerator not pressed. ›› Foot brake pressed. Shut-off conditions: ›› Selector position S2) or tiptronic mode. ›› Brake released. (unless the vehicle is secured by the electro-mechanical parking brake or hill start assist is active). ›› Accelerator pressed. ›› No ATF circulation by Transmission Fluid Auxiliary Hydraulic Pump 1 V475 due to overload protection function or fault. ›› Towing mode detected.Downhill assistDownhill assist helps the driver to maintain a constant speed on downhill gradients. In this case the transmission selects the gear suitable for the gradient in order to maintain the speed selected at the time of braking via the engine brake. Within the bounds of the system's physical limitations it may be necessary to also correct the speed, if necessary, using the brake pedal. Downhill assist cuts out again as soon as the gradient lessens or the accelerator pedal is pressed. Depending on the gradient, downhill assist is active in selector positions D and S while the brake is applied or while cruise control is active.Note: Downhill assist cannot overcome the physical limitations of the vehicle and therefore cannot maintain a set speed in all conditions. The driver must always be ready to apply the brakes! Downhill assist could also be inactive if the brakes were too hot as calculated by the ABS control module.Special features of the steering wheel tiptronic function›› After a long pull of the Tip- shift paddle (long pull-), the transmission changes down into the lowest possible gear. ›› After a long pull of the Tip+ shift paddle (long pull +), the transmission switches from temporary tiptronic mode to automatic mode. ›› In the event of a malfunction of the selector mechanism, the positions P, R, N and D can be selected when the vehicle is stopped and the brake is activated by simultaneously pressing both shift paddles(for longer than one second). ›› The “Tip-shifting in D/S” function, which allows gearshifts to be performed manually at any time, is available. ›› The “Activation of coasting mode using Tip+” function has been deactivated in order to simplify the function assignments of the tiptronic steering wheel in the A8. However, it is still possible to exit coasting mode by pressing Tip-.1) 2)The values given are intended as a guideline. They may deviate depending on the model version.  Neutral idle control is not activated in selector position S in order to allow more direct acceleration. Without neutral control, clutch C or D is immediately closed when drive positions S1 and R are selected. This is why traction is noticeable on selection of 1st gear or R gear and likewise the traction reversal when shifting from 1st gear to R gear (or vice versa). This traction reversal is barely noticeable in selector position D, because when neutral control is active clutch C or D is open and traction cannot be established until the brake has been released.Reference For more detailed information about the neutral idle control function in the 0D5 transmission, refer eSelf-Study Program 990163 The 2017 Audi Q7 Introduction.39 SuspensionOverviewThe suspension of the Audi A8 has been completely redesigned. New technologies and control systems make it even more comfortable, sportier and safer. All models are equipped with adaptive air suspension (PR no. 1BK) featuring electronic damping control. Both the front and rear axles are largely made of light aluminum. Progressive rate steering, which reduces steering effort required by the driver, is standard equipment. The optional dynamic all-wheel-drive steering system, used here for the first time by Audi, combines dynamic steering and rear axle steering. The system improves important subjective and objective driving dynamic characteristics. The brake system offers high performance reserves. A ceramic brake system wheel is optional. With the 9th generation ESC from Robert Bosch GmbH an efficient system is available for all relevant control functions. A wide range of steering wheels, wheels and tires are available for customization. ACC is, for the first time, an integral part of the new driver assistance system in the Audi A8.662_17440 Axles and wheel alignmentFront axleThe front axle is based on the proven design principle of the five-link axle. Special attention was paid to lightweight construction during design.662_175Rear axleThe trapezoidal link rear axle in the predecessor model has been replaced by a newly developed five-link axle. The geometrical arrangement of the links ensures good separation between longitudinal and lateral friction force.Wheel alignmentThe wheel alignment and suspension setup procedures are identical to those for the Audi A4 and Q7 models. The adjustment points are also identical.662_17641 Adaptive air suspensionThe system configuration basically corresponds to those of the Q7 and Q5 models. As in the predecessor A8 model, suspension struts are used on the rear axle instead of separate spring and damper layouts. Drivetrain Control Module J775 is also used for this suspension. In addition to the control software for the air suspension and damping systems, the control module houses sensors for measuring vertical acceleration as well as pitch and roll (torque about the longitudinal and transverse axes of the vehicle). This eliminates the need for the body acceleration sensors required by earlier systems. The control software receives the measurement data on yaw rate (torque about the vertical axis of the vehicle) and transverse acceleration from the Airbag Control Module J234 via the FlexRay bus.Suspension strut with damper and Right Front Damping Adjustment Valve N337Drivetrain Control Module J775 incorporates the control software for air suspension and damping as well as sensors for measuring vehicle dynamicsSuspension strut with damper and Left Rear Damping Adjustment Valve N338 Air supply system with Level Control System Compressor Motor V66 and solenoid valve blockRight Front Level Control System Sensor G289Pressure accumulatorLeft Front Level Control System Sensor G78Suspension strut with damper and Right Rear Damping Adjustment Valve N339Suspension strut with damper and Left Front Damping Adjustment Valve N336Left Rear Level Control System Sensor G76662_17742 Steering systemElectromechanical progressive-rate steering The Audi A8 uses the electromechanical steering system used previously in the 2017 Audi Q7. Progressive steering is standard. An electrically adjustable steering column is basic equipment. A heated steering wheel is available as an option.662_178Dynamic all-wheel-drive steering As a logical development of the all-wheel-drive steering system, offered for the first time in the 2017 Audi Q7, a new system - dynamic all-wheel-drive steering - is optional in the Audi A8. A new feature is the combination of rear axle steering and dynamic steering. This allows the front and rear axles to implement defined steering angles independent of the driver. This improves key subjective and objective dynamic steering characteristics, such as: ›› Smaller turning radius. ›› Reduced steering effort. ›› Much better agility, particularly at low and medium speeds. ›› Improved driving stability, specifically during lanechanging and evasive maneuvers. ›› Improved response and faster vehicle reaction times.662_17943 SuspensionBrake systemFront axle 17 – 18" 6-piston brake calipers are used on the front axle. 10-piston brake calipers are available as an option in combination with the 20” ceramic disc brakes.Front wheel brake662_180Rear axle The rear axle brake calipers (17" and 18", 19" for ceramic brakes) come equipped with the electromechanical parking brake (EPB). As in the current Q7, Q5 and A4 models, the front and rear wheel brakes in the Audi A8 have separate brake circuits.Rear wheel brake with EPB662_181Brake booster 9/9" tandem brake boosters are used.Brake boosterESC unit ESP 9 is used in the Audi A8. Depending on trim level, brake pressure is built up by hydraulic pumps with two or six pistons. In the basic trim of the vehicle, pumps with two pistons are used in combination with a pressure sensor for measuring the driver’s input brake pressure. Vehicles with ACC are equipped with the six-piston version. Here, two additional pressure sensors measure the pressures in both brake circuits. A new function is the loose wheel detection. Loose wheels are detected by evaluating the wheel vibrations. If a loose wheel is detected, the driver receives a warning.ESC unit662_182662_18344 Wheels and tiresIn the basic trim, the Audi A8 comes with 17 – 19" wheels. 18 – 20" wheels are optional. The range of tires extends from 235/60 R17 to 265/40 R20. Tires with run flat capability are not available. The vehicle comes with a tool kit, a jack and a space saver spare.Tire pressure monitoring system The third generation TPMS is standard equipment on the A8. The system is identical in design and working principle to that of the 2017 Audi Q7.(2019 A7 used as an example)669_15845 Electrics and electronicsThe Audi A8 represents the future of the luxury class in the area of vehicle electrics and electronics. Highlights of the vehicle electrics are: ›› Matrix LED headlights (future availability). ›› Rear LED strip with tail lights incorporating OLED technology. ›› Matrix LED reading lights. ›› Rear Seat Remote with OLED display. ›› 48-volt main electrical system with mild hybrid technology. ›› All vehicles are equipped with a belt starter generator (RSG). ›› Heated armrests in the doors, front and rear center armrests as well as a heated steering wheel. ›› 14.1 kWh lithium-ion battery under the luggage compartment floor.J387 J428 J1023A27 R161 J1089 J794 J521J1122J500J792R242J234J245J764 J1088 J104 A31 J898 J285 J527 J869 J853 J136 J1121J1018 J623 J931J519J386Key: A6 A7 A27 A31 J104 J136 J187 J234 J245 J285 J345 Battery, 48 V Voltage Converter, 48 V/12 V Right LED Headlamp Power Output Module 1 Left LED Headlamp Power Output Module 1 ABS/ESC Control Module Memory Seat/Steering Column Adjustment Control Module Differential Lock Control Module Airbag Control Module Sunroof Control Module Instrument Cluster Control Module Towing Recognition Control Module J386 J387 J392 J393 J428 J500 J502 J505 J519 J521 J525 J527 J533 J605 J623 Driver Door Control Module Front Passenger Door Control Module Rear Sunroof Control Module Comfort System Central Control Module Control Module for Adaptive Cruise Control Power Steering Control Module Tire Pressure Monitoring Control Module Windshield Defogger Control Module Vehicle Electrical System Control Module Front Passenger Memory Seat Control Module Digital Sound System Control Module Steering Column Electronics Control Module Data Bus on Board Diagnostic Interface Rear Lid Control Module Engine Control Module46 Installation locations of the control modulesJ927A7J769J505J187J775J392J533J1019A6J772J502 J605 J345 J525 J393 J770J926662_129J764 J769 J770 J772 J775 J792 J794 J853 J869 J898 J926 J927 J931 J1018 Electronic Steering Column Lock Control Module Lane Change Assistance Control Module Lane Change Assistance Control Module 2 Rearview Camera System Control Module Drivetrain Control Module Active Steering Control Module Information Electronics Control Module 1 Night Vision System Control Module Structure Borne Sound Control Module Windshield Projection Head Up Display Control Module Driver Side Rear Door Control Module Passenger Side Rear Door Control Module Assembly Mount Control Module Left Light Control ModuleJ1019 Rear Axle Steering Control Module J1023 Right Light Control Module J1088 Control Module for Left Front Object Detection Radar Sensor J1089 Control Module for Right Front Object Detection Radar Sensor J1121 Driver Assistance Systems Control Module J1122 Laser Distance Regulation Control Module R161 R242 DVD Changer Driver Assistance Systems Front CameraNote Refer to the current service literature for details of control module installation positions, as well as instructions for installation and removal. For further information about the vehicle electrics and electronics of the Audi A8, refer to eSelf-Study Program 970293, The 2019 Audi A8 Electrics and Electronics.47 Climate controlAt vehicle introduction, the 2019 A8 will uses refrigerant R1234yf in the climate control refrigerant system. Audi has been using R1234yf since model year 2017. A new refrigerant is known as R744 will be introduced at a later date. It is C02 and contains neither fluorine nor chlorine and is produced in a series of natural processes without depleting the earth’s ozone layer.Components of the R744 refrigerant circuitConnection to air conditioner with evaporator Service connection, low pressure side Service connection, high pressure sideExpansion valve Low Pressure Side A/C Pressure/Temperature Sensor G1052 AccumulatorCoaxial refrigerant linePressure relief valve, low pressure side AC compressor with pressure relief valve, high pressure sideGas cooler High Pressure Side A/C Pressure/Temperature Sensor G1053662_120Properties of the R744: The essential difference between the new air conditioning system and previous air conditioning systems is the high working pressures in the system. These are required in order to use CO2 as a refrigerant.System pressure ›› Up to 1348.8 psi (93 bar) on the low pressure side. ›› The maximum system pressure on the high pressure side is 2030.5 psi (140 bar).48 New featuresCabin fragrance systemThere is a choice of two different fragrances in the new Audi A8: a summer fragrance and a winter fragrance. The fragrances are stored in two cylindrical containers in Fragrance System Functional Unit GX43, which is located to the left of the steering wheel below the instrument panel. A small fan blows the fragrance into the outer front air outlets. There is a choice of various aroma intensity levels.Air improvement systemTo improve air quality, ionisers are available in the new Audi A8. Ionizers improve air quality through the controlled negative charging of air particles before they are discharged into the cabin via the outer front air outlets.Foot massageThe massage program offers two options allowing the soles of the feet to be massaged either by the linear application of pressure by massaging the reflex zones.Surface heatingThe armrests in the door trims as well as the center armrests in the front and rear are heated surfaces. The heating function is activated and controlled through the seat heater. All heated surfaces are deactivated and regulated through the seat heater. The options here in the US are as follows: ›› Heated front seats standard. ›› Cold weather package: Rear seat heating, front heated surfaces. ›› Rear heated surfaces optional.Back massageAn enhanced back massage feature is available in the new Audi A8. For this purpose, up to 16 bladders are integrated in the front seat and up to 18 in the rear seat. In standard trim, the seats are equipped with double lift bladders. The optional triple lift bladders are designed to provide a higher intensity back massage.Climate control panels in the front and rearThe A8 no longer requires the Climatronic Control Module J255. This means there is no need for separate control module. The climate control is operated via two touchscreens. In terms of visual appearance and tactile feel, both displays are the key innovation in terms user operation. The MMI display and the touchscreen are installed at the center of the instrument panel and at the center of the center console respectively. Climate control functions in the upper MMI display can be accessed through the Car menu. Various control panels are available in the rear area, depending on trim level.Foot heaterThe foot heater in the footrest of the comfort individual contour seat with reclining seat function can only be activated in the unfolded position and in the rest position of the seats. It can be operated through the Smart Remote Control and, like the seat heater and the seat ventilation system, is adjustable to three levels.Reference For further information about the climate control system, refer to eSelf-Study Program 980193, The 2019 Audi A8 Climate Control System.49 Safety and driver assistance systemsPassive safetyIn-car airbagsPassenger side knee airbag Front passenger airbagFront interaction airbagDriver airbagDriver side knee airbagComponentsDepending on trim level, the passive occupant and pedestrian protection system in the 2019 Audi A8 can have the following components and systems: ›› Airbag control module ›› Adaptive driver airbag ›› Adaptive front passenger airbag + (front passenger airbag, two-stage version) ›› Front side airbags ›› Side airbags, 2nd seat row ›› Head airbags ›› Knee airbag ›› Front interaction airbag standard equipment ›› Interaction airbag, 2nd seat row optional equipment ›› Front airbag crash sensors ›› Crash sensors for side impact detection in the doors ›› Crash sensors for side impact detection in the C pillars ›› Crash sensor for side and longitudinal impact de