TECHNICAL DOCUMENTATION

SSP 990593 – The 2019 Audi A7 Introduction

PDFEN116 pages11 MB
SSP 990593 – The 2019 Audi A7 Introduction - PDF cover

This PDF is currently unavailable.

Read document text
The 2019 Audi A7 IntroductioneSelf-Study Program 990593 Audi of America, LLC Service Training Created in the U.S.A. Created 05/2018 Course Number 990953 ©2018 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet. IntroductionOverview Dimensions12 4BodyOverview Body structure Body assembly6 8 106EngineEngine/transmission combinations Fuel tank Exhaust system1415 16 18 20 22 25 26 28 30Power transmissionOverview Drive versions Transmission functions  7-speed dual clutch transmission 0HL Selector mechanism Parking lock manual release20Running gearOverview Axles and wheel alignment Adaptive air suspension (S7) Steering system Brake system3232 33 36 39 41Electrical system and electronicsIntroduction Electrical system Networking Topology Control modules Exterior lighting Interior lighting4444 46 48 50 54 60 68Climate controlOverview72 7472Safety and driver assist systemsPassive safety Active safety Driver assist systems Driver Assistance Systems Control Module J112174 78 79 80Infotainment and Audi connectIntroduction and overview of versions Networking Control Module for Emergency Call Module and Communication Unit J949 Sound Antennas9292 96 98 100 104Inspection and maintenance AppendixeSelf-Study programs109 110 111110Knowledge assessment This eSSP contains video links which you can use to access interactive media.Revision: Final - May 25, 2018This self-study program teaches a basic knowledge of the design and functions of new models, new vehicle components or new technologies. It is not a Workshop Manual. Any figures given here are for explanatory purposes only and refer to the data valid at the time of writing. Content is not updated. It is essential that you refer to the latest technical literature when carrying out maintenance and repair work.NoteReference IntroductionThe 2nd generation of the Audi A7 is a special example of the new Audi design language. Viewed from any perspective, the wider low-set grill and the athletic lines exude sportiness and progressiveness. Flared wheel arches accommodating up to 21 inch rims hint at Audi A7 quattro genes. The full range of Audi connect services has been adopted from the Audi A8 to make the Audi A7 a fully networked Gran Turismo model in the Audi portfolio. With a total of 39 driver assist systems, the Audi A7 is a perfect companion on the road.669_002Learning objectives of this eSelf-Study Program: Once you have completed this eSelf-Study Program, you will be able to answer questions on the following topics: The engine available at market launch. 48 Volt electrical system. New running gear features. New power transmission features. New features of the infotainment systems.1 OverviewThe impressive appearance of the Audi A7 is due mainly to its dynamic and elegant character and a completely new interior design. Like the Audi A8, the Audi A7 is based on Mild Hybrid Electric Vehicle (MHEV) technology.Engine3.0 ltr. V6 TFSI engine with twin-scroll turbocharger Maximum power: 335 hp (250 kW) Maximum torque: 369 lb ft (500 Nm)Driver assist sensorsControl Module for Adaptive Cruise Control J428 is installed in the top left corner of the grill. Laser Distance Regulation Control Module J1122 is installed in the top right corner of the grill.Audi laser lightThe Audi laser light is used and an auxiliary high beam supplementing the LED high beam. The laser spot is activated in addition to the LED high beam at road speeds over approximately 37 mph (60 km.h). This allows the high beam distance to be virtually doubled.2 Displays and operationThe operating and display concept on the Audi A7 uses an MMI touch response system with two touchscreens, a switch module (optional) and a light switch module with haptic and acoustic feedback. Also integrated are intelligent handwritten letter input with full-word and multi-finger recognition. An Audi virtual cockpit with full HD resolution and a head-up display are optionally available.Power transmissionPower transmission on the Audi A7 is exclusively via an automatic transmission. New features include the following: quattro with ultra technology 7-speed dual clutch transmission 0HL New selector mechanism featuring shift-by-wire technology For further information, refer to the section starting on page 26.New light designA design highlight on the Audi A7 is the full-width tail-light band.Electrical systemThe Audi MHEV technology is based on a newly developed 48 Volt main electrical system which also supplies power to the 12 Volt electrical subsystem. The 48 Volt electrical system is powered by a beltdriven starter generator (BSG) which is connected to the engine’s belt drive. A lithium-ion battery, located underneath the luggage compartment floor, is used to store power.669_0033 Dimensions75.1 in (1908 mm)37.7 in (960 mm)64.9 in (1651 mm) 75.1 in (1908 mm)669_00464.4 in (1637 mm) 83.3 in (2118 mm)669_005mm 1 ) )(10 263 in40.37. 3in (949mm )36.4 in (927 mm)115.1 in (2926 mm) 195.6 in (4969 mm)43.9 in (1116 mm)669_006426.3 in (669 mm) 60.0 in (1525 mm)2)57.2 in (1453 mm)3)58.6 in (1490 mm)2)55.9 in (1421 mm)3)46.2 in (1175 mm) 41.3 in (1050 mm)669_007Exterior dimensions and weightsLength Width (not incl. mirrors) Width (incl. mirrors) Height Front track Rear track Wheelbase Unladen weight 195.6 in (4969 mm) 75.1 in (1908 mm) 83.3 in (2118 mm) 55.9 in (1422 mm) 64.9 in (1651 mm) 64.5 in (1637 mm) 115.1 in (2926 mm) 4001 lb (1815 kg)Interior dimensions and other specificationsFront cabin width Front shoulder width Rear cabin width Rear shoulder width Load sill height Luggage compartment capacity Drag coefficient cw Capacity of fuel tank 60.0 in (1525 mm)2) 57.2 in (1453 mm)3) 58.6 in (1490 mm)2) 55.9 in (1421 mm)3) 26.3 in (669 mm) 18.8 cu ft (535 l) 0.27 19.2 gal (73 l)Maximum headroom Elbow room width 3) Shoulder room width1) 2)All dimensions given refer to the unladen weight of the vehicle.5 BodyOverviewLike its predecessor, the body of the Audi A7 is a composite construction using various materials. In addition to various grades of steel, die-cast aluminum is used for the front suspension turret and for the node castings on the rear roof frame. An aluminum reinforcement plate is located on the D-pillar. The bumper carriers with crash boxes, the body brace and the reinforcement struts on the underbody are manufactured from extruded aluminum profiles and the attachments from sheet aluminum. The upper shell of the rear roof frame is made of a new type of steel/plastic composite material. The main joining technologies used are (for steel) spot welding and laser welding on the sill panels, laser soldering on the roof/water channel and (for steel aluminum composite materials) punch riveting with adhesive bonding.Key:Sheet aluminum Die-cast aluminum Aluminum section Ultra-high-strength steel (hot-formed) Modern high-strength steel High-strength steel Soft steel Composite steel/plastic6 669_1177 Body structureThe high torsional strength and crash safety of the body structure on the Audi A7 is achieved by the intelligent mixture of different high-strength to ultra-high-strength types of sheet steel.Key: Sheet aluminum Die-cast aluminum Aluminum section Ultra-high-strength steel (hot-formed) Modern high-strength steel High-strength steel Soft steel Composite steel/plastic669_1188 The number of ultra-high-strength hot-formed sheet steel parts in the passenger compartment has been increased. Some of these steel parts are hardened; others consist of tailored blanks with variable wall thicknesses.They are used in the lower area of the bulkhead, the side members, the rear seat cross members, the top section of the tunnel, the rear longitudinal members, the B-pillars and the A-pillars.669_119Composite steel/plastic materialOne of the innovations and a special feature is the use of composite steel/plastic material for the top section of the rear roof cross member. In this material, a 0.4 mm thick plastic sheet is combined with 0.2 mm thick steel sheets to form a composite sheet. The rigidity and flexural strength is similar to comparable steel parts, while the weight is significantly lower. In the production process, the semi-finished product is deep-drawn just like a regular steel sheet and the two halves of the roof cross member are joined by punch riveting and adhesive bonding. Punch rivets and additional adhesive are also used to join the aluminum cast nodes at the sides.669_1209 Body assemblyFront bumperTo minimize the risk of a pedestrian sustaining knee injuries in the event of a collision with the Audi A7, a mechanism is integrated in the end plate of the front bumper cover to prevent the bumper cover from springing back against the pedestrian’s knee. This mechanism pushes the end plate into the headlight mounting where it latches onto a set of teeth which hold it there. Because damage can occur to the detent mechanism (for example, if the teeth are blunt or broken), both parts must be replaced after an accident. Replacement is intended to ensure that the mechanism functions properly should another pedestrian accident occur. The connection between the end plate and the headlight mounting is made by an end plate adapter which is designed to break on impact. This end plate adapter is the first part to break in small impacts, for example, when parking. In this case, the end plate does not latch onto the headlight mounting. The end plate and the headlight mounting can continue to be used; only the adapter has to be replaced.End plate adapter which breaks upon impactEnd plate in bumper coverHeadlight mounting Teeth669_13010 Instrument panelThe appearance and design of the A7 instrument panel is similar to the 2019 A8 but its structure is fundamentally different. The air outlets do not swivel electrically and do not have the movable covers. Because the trim on the passenger side surrounds the MMI screen and forms a single unit with the top panel, the procedure for disassembling the instrument panel is different to the Audi A8. Always follow the instructions in the most recent service literature.669_133Rear spoilerLike its predecessor, the Audi A7 has a retractable spoiler in the rear lid. At speeds above approximately 75 mph (120 km/h), Rear Spoiler Motor V52 automatically extends the spoiler blade. The spoiler is automatically retracted when the speed drops below approximately 50 mph (80 km/h). A button in Front Information Display Control Head 2 J1060 can also be used to operate the spoiler manually. To retract the spoiler at speeds up to 12 mph (20 km/h), the button in J1060 must be held until the spoiler is fully retracted. The following corresponding messages appear on the MMI display J685: "Press and hold to retract rear spoiler manually" and "The rear spoiler is retracted." At speeds above 12 mph (20 km/h) the button only needs to be pressed briefly. Two Hall sensors monitor whether the spoiler has reached the end positions. One of the sensors measures the end position of the extended rear spoiler while the other counts the number of drive motor revolutions while the spoiler is being retracted. Adjusters allow the height of the spoiler blade to be aligned vertically (z axis) in relation to the rear lid and side panel. Elongated holes are used for alignment in the longitudinal and transverse directions (x and y axes). Drain hoses on the right and left ensure that water can be channeled out of the drive unit for the rear spoiler adjustment. Since molded hoses are used, the markings on both sides must align with each other when the hoses are installed on the mountings.Spoiler bladeAdjusterDrive unit for rear spoiler adjustmentMounting for water drain Water drain hose11 669_132 Panoramic glass sunroofThe Audi A7 can be equipped with a panoramic glass sunroof which spans the entire width of the roof. A piece of glass trim is permanently installed in front of the moving sunroof panel. The glass panel can either be tilted at the rear or it can slide open over the roof towards the rear. An electrically operated blind provides protection against bright sunlight. The water drain hoses on the left and right are located at the rear end of the roof insert. A new feature is that, instead of being clipped into the sunroof frame, the water drain hoses are attached directly to the roof reinforcement at the top and the wheel housing at the bottom.669_13112 13 EngineTorque/power curve Engine with code DLZA   Power in hp/kW   Torque in lb ft/Nm442/600 470/350 553/750 536/400406/550402/300369/500340/250332/450268/200295/400201/150258/300134/100221/30067/50Engine speed [rpm]669_008Features Engine code Type Capacity Stroke Bore Number of valves per cylinder Firing order Compression ratio Power output at rpm Torque at rpm Fuel Turbocharging/supercharging Engine management Maximum injection pressure Lambda/knock control Mixture formation Emission control Emission standard ConceptTechnical data DLZA V6 engine with 90° V angle 183 cu in (2995 cc) 3.5 in (89.0 mm) 3.32 in (84.5 mm) 4 1-4-3-6-2-5 11.2 : 1 335 hp (250 kW) at 5000 – 6400 369 lb ft (500 Nm) at 1370 – 4500 Premium unleaded Twin-scroll turbocharger with wastegate Bosch MDG 1 3625.9 psi (350 bar) Adaptive oxygen sensor, adaptive knock control Direct injection 2 close-coupled ceramic cat. conv. Oxygen sensor before & after cat. conv. LEV3 / Tier3 Mild hybrid (48V)Reference For further information about the engine used, please refer to eSelf-Study Program 920173, The Audi 3.0l V6 TFSI EA839 Engine.14 Engine/transmission combinations3.0 ltr. TFSI engine 335 hp (250 kW) (DLZA) EA839 series7-speed dual clutch transmission 0HL DL382+ -7ARear final drive 09R HL195.U1 MOptional equipment (S7) Rear final drive 0D3 — Sport differential HL195.T2 MKey to manufacturer code designationTransmissionDL382+ -7ATransmission type D = Dual clutch transmission A=A  utomatic planetary transmissionOrientation L = LongitudinalDevelopment number — indicating torque capacity, generation and position of front final driveNumber of speedsFinal drivesHL195.S3 MFront-wheel drive / four-wheel drive A= Four-wheel drive with separate transfer box/center differential or separate fourwheel drive coupling Q= Four-wheel drive with integrated transfer box/center differential F = Front wheel driveInstallation location H = RearOrientation L = LongitudinalCrown wheel diameter in mmFinal drive type S= Standard (open differential) T= Torque Vectoring (sport differential) U= ultra technology (quattro ultra)Manufacturer code: Version 1 = 1st generation M = Magna Powertrain 2 = 2nd generation 3 = 3rd generation15 Fuel tankThe A7 has a 19.2 gal (73 l) fuel tank. A tank cut-off valve is installed in the lower part of the tank. The end of the pipe from this valve is located in the upper part of the liquid trap. The TFSI tank requires several roll-over valves for ventilation.Filler neck (capless)Breather line (inserted through longitudinal member)How the tank is emptied When driving, fuel is pumped into the side chamber by the suction-jet pump. The vacuum produced in the pump causes fuel to be transferred from the side chamber to the main chamber, so the side chamber is emptied first.How the different tank capacities are achieved Baffles are used to achieve the different tank capacities. The volume of the fuel tank is changed by the baffles.Baffle plateReservoir with integrated fuel filter in delivery unit (long-life) Level sender for main chamberTank cut-off valve16 Capless filler neck The capless filler neck technology used on the Audi TT is used on the Audi A7. A dual flap system is used for dust protection. The first flap provides a seal against dust, while the second seals against fuel. Plastic seals are used to seal the tank tightly against the outside.Sealing flap 1Return springFuel tank breatherSeal Sealing flap 2SealReturn spring669_041Liquid trapBreather line Aggregate jet line Baffle plate Suction-jet pump with drive line connected Level sender for side chamber669_01717 Exhaust system3.0 ltr. TFSI engineThe gas flow paths are very short because the turbocharger module is located in the inner V. The catalytic converter is bolted directly to the turbocharger outlet. This allows the converter to achieve light-off very quickly after a cold start.Catalytic converter module The module is flanged-mounted directly to the turbocharger, which houses the main and secondary catalytic converters. Both catalytic converters are ceramic-type catalytic converters.Main catalytic converterSecondary catalytic converterCenter muffler works on the absorption principleDamper elementFront mufflers work on the absorption principleRear muffler works on the reflection and absorption principle669_02418 Engine mountsThe engine of the A7 has a three-mount system. There are two switchable mounts on the engine and a hydraulic mount on the transmission. This system achieves an extremely comfortable ride by switching the two engine mountings between soft (vehicle idling, current supply to mounting on) and hard (vehicle in motion, current supply to mounting off).669_124Right Electro-hydraulic Engine Mount Solenoid Valve N145Left Electro-hydraulic Engine Mount Solenoid Valve N144Hydraulic transmission mountingHydraulic transmission mount The hydraulic transmission mount is installed at the rear section of the transmission and counteracts the drive forces.Engine mount diagnosis The VAS Scan Tool is used to read measuring values of the current being supplied to the engine mounts.Hydraulic engine mounting669_126Left Electro-hydraulic Engine Mount Solenoid Valve N14419 669_028 Power transmissionOverviewThe power transmission system of the A7 has much in common with the latest Audi A4, Q5, and Q7. Please refer to the eSelf-Study Programs for those vehicles for further information.Manual release cable for parking lockSelector mechanism with shift-by-wire and park-bywire technology Refer to page 287-speed dual clutch transmission 0HL Refer to Overview – Automatic transmissionFour-wheel drive coupling 0CXActuator unit for Parking lock manual release Refer to page 30The illustration shows the drive train of the V6 3.0 ltr. TFSI with S tronic and the quattro four-wheel drive system with ultra technology.7-speed dual clutch transmission 0HL – S tronic The 7-speed dual clutch transmission 0HL is new. This is a new version of the DL382 transmission series for four-wheel drive featuring quattro with ultra technology. Specific measures have been implemented to raise the torque capacity. Refer to page 26. To transmit this amount of torque to the rear axle, the 0HL transmission is used in combination with the four-wheel drive coupling 0CX and rear final drive 09R. Refer to page 26.quattro with ultra technology The quattro four-wheel drive system with ultra technology is new to this class of vehicles (C8 series). To extend the possible applications of this four-wheel drive system, it was designed for engine torques up to 369 lb ft (500 Nm). The following four-wheel drive concepts are available on the Audi A7: quattro with ultra technology. quattro with self-locking center differential. quattro with sport differential.Front-wheel drive and hybrid drive versions are planned for future model releases.20 Overview Depending on engine selection, the following transmission options are available:PR no. G1C G1D G1G1)Manufacturer designation DL382-7F DL382-7A AL552-8QService designation 7-speed dual clutch transmission 0CK 7-speed dual clutch automatic transmission (A7) 8-speed automatic World-wide automatic transmission options 0D5 (S7)Marketing designation S tronic S tronic tiptronicDrive version Front-wheel drive quattro with ultra technology quattro with self-locking center ­differential quattro with sport differential (optional)Overview Depending on the quattro concept and equipment choices, the following rear final drive versions are available:PR no. GH1 GH2 GH4 Manufacturer’s designation HL195.S3 M HL195.T2 M HL165.U1 M Service designation Rear final drive 0G2 (S7) Rear final drive 0D3 (S7 optional) Rear final drive unit 0B0 (S7) Four-wheel drive version quattro with self-locking center ­ differential quattro with sport differential (optional) quattro with ultra technologyRear final drive 09R with dog-clutch Refer to page 23669_063 21 Drive versionsquattro with ultra technology/four-wheel drive couplingFour-wheel drive coupling 0CJ or 0CX is installed in the Audi A7 with quattro ultra, depending on the engine version. The basic design and operating principle of the two versions are identical. They differ exclusively in terms of the coupling torque which can be transmitted. Four-wheel drive coupling 0CJ is rated for torque levels up to 590 lb ft (800 Nm). Four-wheel drive coupling 0CX is rated for torque levels up to 885 lb ft (1200). Four-wheel drive coupling 0CX has two additional clutch plate pairs to enable transfer of the higher torque level. Four-wheel drive coupling 0CX is slightly longer than fourwheel drive coupling 0CJ due to these changes. All Wheel Drive Control Module J492 can display two different driver warning messages in the instrument cluster:Four-wheel drive:  fault. You can continue driving. Please contact dealership Meaning: a malfunction has occurred. The customer can continue driving but should drive to a dealership soon to have the fault corrected. The four-wheel drive system may be unavailable.Four-wheel drive coupling 0CX VTK1201)669_064Four-wheel drive:  overheating. Please adapt driving style. See owner's manual Meaning: the vehicle has been driven hard, causing the temperature of the fourwheel drive coupling to rise significantly. A more restrained driving style is required so that the coupling can cool down. Until then, the four-wheel drive system will be unavailable. When the temperature has dropped back down to normal, the driver message will disappear and the four-wheel drive system will be available again.ATF filler and inspection plug Accessible after removal of vibration damperFour-wheel drive coupling with 7 pairs of platesAll Wheel Drive Control Module J492 with All Wheel Drive Clutch Actuator V622 and All Wheel Drive Clutch Position Sensor G969ATF drain plug1)669_065Manufacturer’s internal designation:  VTK120 = Coupling with 1200 Nm coupling torque – Four-wheel drive coupling 0CX VTK080 = Coupling with 800 Nm coupling torque – Four-wheel drive coupling 0CJReference For further information about quattro with ultra technology, refer to the following eSelf-Study Program 990173, The 2018 Audi Q5 Introduction.22 quattro with ultra technology/rear final driveRear final drive 0B0 or 09R is installed in the Audi A7 with quattro ultra, depending on the engine version. The basic design and operating principle of the two versions are identical. They differ exclusively in terms of the drive torque which can be transmitted.The following are the main components which have been modified compared with final drive 0B0 to enable the higher level of drive torque to be transmitted by final drive 09R: Final drive gear set increased in size (crown wheel ⌀ 195 mm instead of ⌀ 165 mm on final drive 0B0). Differential increased in size (ball ⌀ 90 mm instead of ⌀ 80 mm on final drive 0B0). Dog-clutch increased in size (diameter, shafts, etc.). Bearings, flange shafts and housing increased in size. Bearing for left flange shaft: 2 needle bearings. Deflector used for oil circulation.669_061Gear oil drain plugGear oil filler and inspection plug Deflector to ensure accurate oil flowRear final drive 09RAll Wheel Drive Clutch Actuator 2 V623Driveshaft Speed Sensor G970669_067 23 quattro with self-locking center differentialFor engines developing more than 369 lb ft (500 Nm) of torque, the 8-speed automatic transmission 0D5 is installed in conjunction with a self-locking center differential. In conjunction with rear final drive 0G2 (with standard differential), this four-wheel drive version is called quattro with self-locking center differential. As an option, the 8-speed automatic transmission 0D5 (with self-locking center differential) can be combined with the sport differential (rear final drive 0D3). This four-wheel drive version bears the name quattro with sport differential.quattro with sport differentialThe 0D3/0BX sport differential is an evolutionary, second-generation unit based on the 0BF sport differential. The key modifications in sport differential 0D3 are: Final drive housing matched to the rear axle. Welded crown gear and various weight-saving measures New gear oil and ATF. Shortened sensors for more clearance to exhaust system. Dual control module concept in conjunction with J775 and J187. Renaming of the sport differential control module – previously J492, now J187. New Address word – previously 0022, now 0032.The basic hardware of the sport differential (torque redistribution units, hydraulic control unit, sensors and actuators) is to a large extent identical to that of the first-generation sport differential.8-speed automatic transmission 0D5 tiptronicDrivetrain Control Module J775Self-locking center differential with asymmetrical-dynamic torque split Two geometrically different center differentials from two different manufacturers may be installed depending on the engine version. Both versions have similar properties. The version here is made by JTEKT. The other version is made by AAM.669_069 24 Sport differential – Dual control module conceptThe key modification in the second-generation sport differential is the dual control module concept. In the case of the first-generation sport differential (sport differential 0BF/0BE), All Wheel Drive Control Module J492 is responsible for computing the redistribution of torque and controlling the actuators. On the second-generation sport differential (sport differential 0D3/0BX), the redistribution of torque for the sport differential is computed by Drivetrain Control Module J775. J775 acquires information on driving status centrally, processes this and computes the value for the redistribution of torque. This value is then transmitted to the Differential Lock Control Module J187 via the FlexRay data bus. Using this information, J187 computes the drive voltage for the actuators and the required redistribution of torque. J187 is therefore purely responsible for performing the task. The dual control module concept enables torque to be redistributed with greater precision and speed than in the first-generation sport differential, ultimately improving dynamic control. Torque distribution display: The driver can display the qualitative distribution of drive torque to the wheels in a graphic on the MMI screen. To do so, the following menu item must be selected: Car Vehicle information quattroTransmission functionsThe functions of the DL382 transmission are virtually the same as in the 2017 A4 and 2018 Q5. More information can be found in the respective eSelfStudy Programs. The functions of the AL552 transmission are virtually the same as in the Audi Q7 and 2019 Audi A8.FlexRay data busDifferential Lock Control Module J187Data Bus on Board Diagnostic Interface J533Rear final drive 0D3 Sport differential (optional) or Rear final drive 0G2 Standard669_06825 7-speed dual clutch transmission 0HLThe 0HL transmission is a variant of the DL382 series1). Specific measures have been implemented in order to raise the torque capacity from the previous level of 295 lb ft (400 Nm) to 369 lb ft (500 Nm). In order to transmit this amount of torque to the rear axle, the 0HL transmission is used in combination with the four-wheel drive coupling 0CX.Selector lever for parking lock manual release Changing the lever position: refer to page 28.Four-wheel drive coupling 0CX669_070ATF heat exchanger increased in size 2 additional cooling plates1)All Wheel Drive Control Module J492The DL382 transmission series currently comprises the following variants: DL382-7F –  7-speed dual clutch transmission 0CK2) DL382-7Q – 7-speed dual clutch transmission 0CL3) DL382-7A – 7-speed dual clutch transmission 0CJ3) DL382+-7A – 7-speed dual clutch transmission 0HL3)A key to the code designations can be found on page 15. 2) This variant is available with and without shift-by-wire. 3) This variant is available only with shift-by-wire.Gearset and bearings Shot-peened toothing Optimised transmission bearingsATF drain plug – four-wheel-drive coupling26 Lubrication The 0HL transmission has two oil systems: an ATF system for the dual clutch and the electrohydraulic control unit, and an MTF system for the gear set and the front final drive. The ATF must be changed at specified intervals, but the MTF is designed to provide lubrication for the lifetime and does not require servicing. The four-wheel drive coupling 0CX has a separate oil system with ATF. The ATF does not have to be changed and does not require servicing.Dual clutch with enhanced durability One extra clutch plate per clutch and cross bar design Piston surface area increased by 10%Dual-mass flywheel with pendulum-type absorber Modified for higher engine torque669_072Pinion shift running on double tapered roller bearingOther modifications: Modification to design of intake for ATF Software modifications Increased ATF pump rate for more cooling oilSpacer ring on pinion shaftKey: Input, gear train half 1 Input, gear train half 227 Selector mechanismThe Audi A7 uses the latest Audi selector mechanism design with full shift-by-wire (SBW) capability. This means that parking lock operation is also fully automatic. The term used for this is "park-by-wire" (PBW). There is no selector cable connecting the selector mechanism to the transmission. With the introduction of this selector mechanism design to the C-series, all Audi models with longitudinal engines now use this technology and operating concept. The selector mechanism has been completely redesigned for the C8 model range. It is much more compact, lighter and more cost-efficient while retaining the original functions. The new selector mechanism (E313) is a single unit with the following components: J587 Selector Lever Sensor System Control Module G868 Transverse Selector Lever Lock Sensor G727 Selector Lever Position Sensor V577 Transverse Selector Lever Lock Motor N110 Shift Lock SolenoidThe complete unit must be replaced if one of these components is defective.669_073Function diagram – selector mechanismKey: E313 Selector Lever E681 Selector Lever Release Button E816 Parking Lock Button G727 Selector Lever Position Sensor G868 Transverse Selector Lever Lock Sensor J587 Selector Lever Sensor System Control Module K320 Parking Lock Indicator Lamp N110 Shift Lock Solenoid V577 Transverse Selector Lever Lock Motor Y5 Selector Lever Transmission Range Display A,B,C ConnectorsInterface to Parking Lock Solenoid – N486 + (pin A1) Interface to Parking Lock Solenoid – N486 - (pin A2) CAN High CAN Low28}Only on DL382-series transmission669_074}Dash panel insert CAN Selector lever handle – Top sectionSelector lever handle – Bottom section with selector lever bootSelector Lever Release Button E681Parking Lock Button E618 with Parking Lock Indicator Lamp K320. K320 illuminates the P button (dimmed) and is brightly lit when the parking lock is activeSelector Lever Transmission Range Display Y5Connector C Selector leverSelector LeverE313 Connector BSelector Lever Sensor System Control Module J587669_075Selector mechanism versions On vehicles with the 7-speed dual clutch transmission 0HL, Selector Lever Sensor System Control Module J587 has two additional interfaces for controlling the Parking Lock Solenoid N486. Refer to the function diagram in “669_074“ page 28. Information exchange Data is exchanged between the selector mechanism and the transmission via the gateway. J587 communicates via the CAN dash panel insert; Automatic Transmission Control Module J217 communicates via the FlexRay with Data Bus On Board Diagnostic Interface J533.Connector AConnector B669_07629 Parking lock manual releaseThe design and operating concept for the parking lock manual release mechanism have been largely adopted from the B9 series. The design of the actuator unit and the wrench for the Audi A7 have been revised. The new features and special characteristics are described below.Transmission selector lever for parking lock manual releaseSpecial features of manual parking lock release (compared to B9 series and Q5) The position of the manual release lever on the transmission has been changed. This has enabled the optimization of the cable guide for the manual release mechanism, a reduction in operating force. The wrench for the manual release mechanism has a withdrawal lock. In conjunction with the adapted stop in the actuator unit, the wrench can only be withdrawn approximately 5 mm (in order to release the lock) while in the actuated position (P-OFF). The wrench can then be turned back and withdrawn (P-ON position). This prevents the possibility of the wrench unintentionally being removed completely in the actuated position and of the manual release mechanism springing back. Note: Starting at the beginning of 2018, the manual release mechanism with withdrawal lock will also be installed in B9-series vehicles and in the Audi Q5.Wrench Audi A7Wrench B9 series/Audi Q5Withdrawal lock Without withdrawal lockStop for withdrawal lockActuator unit for parking lock manual release669_078 30 Installation location of the manual release mechanism The actuator unit for the manual release mechanism is located under the cup holder in the center console. The acutator unit can be accessed by removing the rubber mat and the cover. Please note that the wrench must not be inserted vertically, but at an angle of approximately 13°. Refer to image “669_079“ page 31.669_0801Socket wrench≈13°23A669_077Actuator unit for parking lock manual releaseManual release of parking lock (P-OFF position)669_079 DANGERCaution! Before actuating the parking lock the vehicle must be secured to prevent it from rolling away.View AMake sure that the wrench and the stop in the actuator unit are undamaged. Please observe the safety warnings in the Owner's Manual. Deactivating the manual release mechanism (P-ON position) Pull the wrench out as far as the withdrawal lock (approximately 5 mm) and, holding it firmly, turn it back as far as the stop. The socket wrench can now be removed. Note: Do not under any circumstances turn the wrench only counter-clockwise because as this will damage the actuator unit and the wrench.1 2 3Insert the wrench into the actuator unit as shown.Turn the wrench clockwise as far as the stop, then push it down about 5 mm to lock it into place at the stop.31 Running gearOverviewThe running gear for the Audi A7 has been completely redesigned compared to the previous model. The technology and control systems used are similar to the 2019 Audi A8 Versions are available with steel suspension and controlled or non-variable damping in addition to air suspension with electronic damping control. The front and rear axles are based on a high-precision lightweight five-link design. Progressive steering, included as standard vehicle equipment, reduces the amount of steering effort required. The dynamic four-wheel steering system introduced in the Audi A8 is available as an optional extra for the Audi A7 . The brake system delivers superb performance even when a more dynamic driving style is adopted. The 9th generation ESC system provides high-performance stability control for the vehicle.669_138The following suspension variants are available for the Audi A7: Running gear with steel suspension and non-variable damping (1BA) This is the standard running gear. Sport running gear with steel suspension and non-variable damping (1BE) This suspension system is optional. The springs, dampers and anti-roll bars are set up for dynamic handling. The ride height is approximately 10 mm lower than version 1BA. Suspension with air springs and damping control (adaptive air suspension – 1BK) This suspension system is optional for the Audi S7. The ride height in "Auto" mode (normal level) is approximately 10 mm lower than version 1BA (S7).32 Axles and wheel alignmentFront axleThe front axle is based on the proven design principle of the five-link suspension. A particular emphasis was placed on the lightweight construction. The main components are constructed from aluminum. The underlying platform is the MLBevo system, which has already been used as a development base for the current A4, Q5, Q7 and A8 models.Upper transverse links Forged aluminum component Adopted from the Audi Q7 Bonded rubber bushing (new component) Wheel bearing housing Forged aluminum component Adopted from the Audi Q5Shock absorber Single and twin-tube versions with non-variable or controlled damping Shock absorber mounting MLBevo system component669_139Subframe Three sections, base carrier sheet steel construction with cast aluminum support brackets adopted from Audi Q5 with modifications to anti-roll bar bolt attachment and rear connection of base frame.Guide link Forged aluminum component Adopted from Audi Q5 including hydro-bushingCoupling rod Two versions in plastic or aluminum depending on running gear variant MLBevo system componentsAnti-roll bar Tubular anti-roll barsTrack control link Forged aluminum component Basic part adopted from Audi Q7 Bonded rubber bushing (new component)Wheel bearing/wheel hub Second generation wheel bearing MLBevo system component669_14033 Rear axleThe trapezium link rear axle used in the previous model has been replaced by a new five-link axle. This is based on the MLBevo platform, which has already been used on the A4, Q5, Q7 and A8 models. The geometric layout of the suspension links provides a separation in the absorption of longitudinal and lateral forces. Elastomer bushings with a mixture of high-damping materials and integrated spacer sleeves allow for a high degree of radial stiffness with a low roll rate. The use of subframe bushings with hydraulic damping ensures the axle is well-isolated from the vehicle body. The wheel bearings have been optimized to reduce friction, which helps to decrease rolling resistance.Upper transverse link (rear) Sheet-steel part Adopted from the Audi Q7 Bearings (hub carrier end) adopted from Audi A8 Subframe Welded steel construction Geometry adopted from Audi A8 Newly developed subframe mountings669_141Shock absorber Single-tube on 1BA and 1BE Twin-tube on 1BL and 1BKAero-deflectors for spring links New component, similar in geometry to Audi Q5Upper transverse link (front) Forged aluminum component adopted from ­ Audi Q5Track rod Vehicles with steel coil springs: Sheet-steel part Adopted from the Audi Q7 Vehicles with adaptive air suspension: Forged aluminum component Adopted from the Audi Q7Lower transverse link (front) Forged aluminum ­component Adopted from Audi Q5 with high axle load (Q5 Security)Coupling rod 2 versions: Aluminum/plastic Aluminum: adopted from Audi Q5 Plastic: new componentLower control arm Forged aluminum component Adopted from the Audi Q5Anti-roll bar Tubular anti-roll bar Geometry same as Audi Q5 Modified spring rateHub carrier Die-cast aluminum Adopted from the Audi Q534Wheel bearing/wheel hub Adopted from the Audi Q5669_142 Wheel alignmentThe wheel alignment and adjustment procedures are the same as for the other MLBevo models. The adjustment points are also identical, for both the steel suspension and the adaptive air suspension.Toe setting at attachment point: track rod/subframe (not shown in illustration)Camber setting at attachment point: lower control arm/subframe (hidden by aero-deflectors)669_141CamberbalancingToe setting669_139Note Before beginning wheel alignment, it is necessary to check whether the steering adapter (on vehicles without dynamic four-wheel steering) or the rear axle steering unit is installed in the correct position on the subframe. If not, it may cause different variations in toe angle on each of the wheels when the suspension compresses and rebounds.35 Adaptive air suspension (S7)Design and functionThe adaptive air suspension is optional for the Audi S7. The system has the same general layout as the adaptive air suspension system in the Audi Q5. Drivetrain Control Module J775 is also installed. In addition to the regulating software for the air suspension and damping, the control module has the sensor for registering vertical acceleration (upwards acceleration of the vehicle) as well as pitching and rolling moments (rotation about the vehicle’s lateral and longitudinal axes). This eliminates the need for the body acceleration sensors installed in previous systems. The measured values for the yaw rate (rotation about the vehicle’s vertical axis) and the lateral acceleration are transmitted via FlexRay from the airbag control module to the regulating software. The compressor for the air supply unit is the same as on the Audi Q5 (2-stage without boost function). The solenoid valve block is also the same. The vehicle level sensors have also been adopted from the Audi Q5. Air intake is via the left wheel housing. Two aluminum accumulators with a total volume of approximately 1.1 gal (4.4 l) are used. These are installed in the rear area of the side sills. The maximum system pressure is approximately 261.0 psi (18 bar).Air spring strut with damper Right Front Damping Adjustment Valve N337Drivetrain Control Module J775 incorporating the control software for the air suspension and damping systems as well as sensors for measuring vehicle dynamics ­Accumulator Right Rear Damping Adjustment Valve N339Air supply unit with Level Control System Compressor Motor V66Right Front Level Control System Sensor G289Left Rear Damping Adjustment Valve N338Air spring strut with Left Front Damping Adjustment Valve N336Left Front Level Control System Sensor G78Right Rear Level Control System Sensor G77AccumulatorLeft Rear Level Control System Sensor G76669_14336 For the first time on an Audi model, the accumulators on the Audi S7 are located in the side sills. The accumulators, which are secured to retaining plates, are installed by pushing them into the sills from the rear wheel housings. The retaining plates are bolted to the end face of the sills in the wheel housings. This design solution utilizes the otherwise empty space inside the sills efficiently and frees up space elsewhere on the vehicle.Accumulator669_144The air springs on the rear axle are also new. The inside of the U-bellow pistons, whose geometrical form defines the spring characteristics, consists of activated charcoal. After shrinkage, the activated charcoal monoliths are adsorptive, that is, they bind air molecules on their surface. This increases the geometric volume in the air springs by about one third and increases the suspension comfort.U-bellows piston669_145A further new feature is the design of the suspension turrets on the front axle. Where steel material has been used previously, plastic/aluminum hybrid components are now in use. The inner housing, which takes up the major proportion of the load, consists of aluminum, and is surrounded by plastic on the outside. This lightweight construction enables a weight reduction of approximately 3.0 lb (1.4 kg) per vehicle. Residual pressure valves on the air connections of the suspension struts ensure a minimum pressure of 2 - 3 bar.Plastic/aluminum suspension turretResidual pressure valve669_146 37 Control strategyModeLevelΔ [mm]Bars shownliftHL1+205 barscomfort auto dynamicNL03 barsLL1-101 bar22 (35)43 (70) 50 (80)62 (100)75 (120) Speed mph (km/h)Key:Hysteresis 3 mph (5 km/h) Selection lock 3 mph (5 km/h) HL1 = High level NL = Normal level669_147LL1 = Low level 1Drivers can adjust the suspension and damping characteristics on the Audi S7 to suit their personal preferences in the usual way using Audi drive select. Three different maps are available for this in the running gear control module. Service operations The service operations are the same as for the systems which are already used on other Audi models (Q5, Q7 and A8). When transport mode is activated, high damping forces are applied in order to counteract movements of the vehicle initiated by the transporting vehicle. The high level is selected in addition when shipping mode is activated, and controlled to ensure maximum ground clearance. These modes are automatically deactivated after the vehicle has been driven approximately 62 mi (100 km) or faster than 62 mph (100 km/h) if not previously done using the VAS Scan Tool.38 Steering systemThe A7 uses the same electromechanical power steering used in the 2018 Audi Q5. Progressive steering is standard. Dynamic four-wheel steering is optional.669_149The standard electromechanical version of the A7 steering system has a mechanically adjustable steering column. It has lengthwise movement of approximately 2.4 in (60 mm) and approximately 2.0 in (50 mm) of height movement. An electrically adjustable steering column is optional. It has been adapted from the 2019 A8. The steering column on vehicles with dynamic four-wheel steering are shorter to provide room for the dynamic steering actuator.669_150Two steering wheels are available for the Audi A7 . The double-spoke leather steering wheel with 12 multi-function buttons is the standard version. For all steering wheels, the leather on the steering wheel and selector lever handle are matched to the preferred color of the dash panel top. Steering wheels with paddle levers and/or steering wheel heating are optional. The sportiest version, the sport contour leather steering wheel, has a more contoured rim and is flattened at the bottom. A heated steering wheel is optional.Sport contour leather steering wheel S7 Sport leather steering wheel with paddle levers A7669_15139 Dynamic four-wheel steering (S7)The dynamic steering system of the S7 is optional. In terms of design, function, serviceability and operation, it is identical to the system of the 2019 A8.Dynamic steering actuatorActive Steering Control Module J792Rear Axle Steering Control Module J1019669_152Power Steering Control Module J500Drivetrain Control Module J775Reference For further information, please refer to eSelf-Study Program 960293, The 2019 A8 Running Gear and Suspension Systems.40 Brake systemAs with the current MLBevo models A8, Q7, Q5 and A4, the brakes on the front and rear axles of the Audi A7 have separate brake circuits ("black and white" system).Front axle Engine Minimum wheel size Type of brakes 3.0l V6 TFSI (335 hp [250 kW]) 18" AKE fixed caliper brakes (30-36-38) 6 14.7 in (375 mm) 1.4 in (36 mm) Rear axle 3.0l V6 TFSI (335 hp [250 kW]) 17" TRW EPBi 43Number of pistons Brake disc diameter Brake disc thickness1 12.9 in (330 mm) 0.8 in (22 mm)669_153669_154AKE fixed caliper brakes on front axleTRW EPBi 43 brakes on rear axle with electro­ mechanical parking brakeThe A7 uses an 8/9” brake servo. Because the A7 is equipped with a 48 volt electrical systems, a movement sensor is installed instead of a brake light switch. The PWM signal from this sensor is used to initiate recuperation.The 2019 A7 uses the 9th generation ESC. Vehicles with ACC use a hydraulic pump with six pistons and have two additional sensors. Vehicles without AAC use a four piston pump. The function, data communication, operation, driver information and service operations are the same as the ESC system of the 2019 A8. The new loose wheel detection/ warning system introduced on the Audi A8 is also used on the A7.669_155669_156Reference For further information, please refer to eSelf-Study Program 960293, The 2019 Audi A8 Running Gear and Suspension Systems.41 Tire pressure monitoringThe A7 comes equipped with the standard tire pressure monitoring system. The system has the same design and function as the system in the Audi Q7 and Audi A8.669_158The Tire Pressure Loss Indicator is an indirect measurement system. The values measured by the wheel speed sensors are used to calculate the tire circumferences and vibrations. The software is integrated in the ABS Control Module J104.Reference For further information, please refer to eSelf-Study program 960293 The 2019 A8 Running Gear and Suspension Systems.42 43 Electrical system and electronicsIntroductionThe electrical system and electronics of the 2019 are very similar to those of the 2019 A8. Various CAN bus systems are used in the vehicle electrical system and network. The FlexRay bus system allows realtime data transfer between the running gear control modules and the driver assist system control modules. FlexRay allows all regulating systems to access the sensors. In comparison to the previous bus architecture the bandwidth has grown by a factor of 20. The electrical system of a typical sedan may consist of 1500 individual wires and weighs about 110 lb (50 kg). The weight of the electrical system in the A7 has been reduced despite the numerous new functions. This was done by using wire cross sections as small as possible. Further reduction was made by using an aluminum main battery cable. The available HD matrix LED headlights are a statement of the new light design language of the Audi A7. Separated by narrow gaps, 12 light segments are next to each other and operate together digitally. Audi offers two lighting interior packages for the Audi A7 : The contour lighting package. The contour ambient lighting package. The ambient lighting in the instrument panel and the center console allows the architecture to "float". In the door, this increases the effect of space. Precise contour lighting runs along the center console and the door trim; the quattro badge is also illuminated. The narrow and precise placement of the light bands traces the entire interior architecture, thereby underlining the entire interior concept. The contour lighting can be set to 30 different colors and follows the color profiles in the Audi drive select driving dynamics system. White light accents also shine from the bass speakers in the doors if the Bang & Olufsen Advanced Sound System with 3D sound is installed. Illuminated sill panel trim (standard with the design selection and S line sports package) round off the interior lighting program.Overview of electrical system and vehicle electrics Main battery wireJump start terminal669_116LED headlight44 Control module rackThe installation of many control modules is now on a control module rack installed in the underbody of the luggage compartment. Depending on the options installed in the vehicle, the following modules may be located there: Relay and Fuse Panel 4 SR4. Rear Spoiler Control Module J223. Comfort System Central Control Module J393. A 12 Volt power distributor. Control Module for Emergency Call Module and Communication Unit J949. Cellular Telephone Amplifier R86. Differential Lock Control Module J187.Installation locationRelay and Fuse Panel 4 SR4 12 Volt power distributor Rear Spoiler Control Module J223 Towing Recognition Control Module J345 (Not used in North America) Comfort System Central Control Module J393 Differential Lock Control Module J187Control Module for Emergency Call Module and Communication Unit J949669_054Cellular Telephone Amplifier R86Parking Heater Radio Receiver R64 (Not used in North America)Windshield Defogger Control Module J505 (Not used in North America)45 Electrical systemThe A7 is equipped with both a 48 volt electrical system and a 12 Volt electrical system. The 48 volt electrical system is the main electrical system. The current is generated via the 48 volt belt starter-alternator when the engine is running. The installation location and function of the batteries, voltage converter, 12 volt starter motor, and the 48 volt starter/alternator are identical to those of the 2019 A8.Wiring junctions TV2 and TV3 with jump-start terminal48 Volt positive wireRelay and Fuse Panel 3 SR3 on lower section of right A-pillar48 Volt belt starter-alternator12 Volt starterFuse Panel F SF on instrument panel (left-side)Relay and Fuse Panel 1 SR1 in plenum chamberRelay and Fuse Panel 2 SR2 at foot rest (left-side)46 Please refer to eSelf-Study Program 970293, The 2019 Audi A8 Electrics and Electronics for more detailed information about the descriptions and operation of the components listed on this page.12 Volt main battery wireVoltage converter, 48/12 Volt, A7Battery, 12V, A in rear right side panelBattery, 48V, A6 in spare wheel wellRelay and Fuse Panel 4 SR4 on control module rack in luggage compartment669_18147 NetworkingInstallation location of control modulesAlways refer to the current service literature for information about the installation location and service procedures for control modules as well as instructions for installation and removal.J387 J1089A27R7 J1122J521 J794J500J792R242J234J245 J77J428 J764 J898 J285 J527 J853J136J112A31J104 J623J1088 J869 J519 J386Key: A6 A7 A27 A31 J104 J136 J187 J223 J234 J245 J285 Battery, 48 V Voltage Converter (48 V/12V) Right LED Headlamp Power Output Module 1 Left LED Headlamp Power Output Module 1 ABS Control Module Memory Seat/Steering Column Adjustment Control Module Differential Lock Control Module Rear Spoiler Control Module Airbag Control Module Sunroof Control Module Instrument Cluster Control Module J386 J387 J393 J428 J500 J502 J519 J521 J525 J527 J533 J605 J623 J764 Driver Door Control Module Front Passenger Door Control Module Comfort System Central Control Module Control Module for Adaptive Cruise Control Power Steering Control Module Tire Pressure Monitoring Control Module Vehicle Electrical System Control Module Front Passenger Memory Seat Control Module Digital Sound System Control Module Steering Column Electronics Control Module Data Bus on Board Diagnostic Interface Rear Lid Control Module Engine Control Module Electronic Steering Column Lock Control Module48 J927A7J7691 J187 J1019 A6 J772 J223 R86 J949J393 J53375621 J502J605J525J770J926669_182J769 J770 J772 J775 J792 J794 J853 J869 J898 J926 J927 J949 Lane Change Assistance Control Module Lane Change Assistance Control Module 2 Rearview Camera System Control Module Drivetrain Control Module Active Steering Control Module Information Electronics Control Module 1 Night Vision System Control Module Structure Borne Sound Control Module Windshield Projection Head Up Display Control Module Driver Side Rear Door Control Module Passenger Side Rear Door Control Module Control Module for Emergency Call Module and Communication Unit J1019 Rear Axle Steering Control ModuleJ1088 J1089 J1121 J1122 R7 R86 R242 Control Module for Left Front Object Detection Radar Sensor Control Module for Right Front Object Detection Radar Sensor Driver Assistance Systems Control Module Laser Distance Regulation Control Module DVD Player Cellular Telephone Amplifier Driver Assistance Systems Front Camera49 TopologyJ926 J386J927J387J605 Data Link ConnectorN209J136J764J453N475J245U13A6N210J521J367A7N477CH12J223Comfort System Central Control Module J393G65G578Control motors 1 - 2Vehicle Electrical System Control Module J519A31A27J938Heater controls 1 - 4 ­MX3E265MX4Control motors 1 - 15Ambient light 1 - 15J866MX13Ambient light 16 - 30V388 V390MX13Ambient light 31 - 45V389 V391J1169J126E1J1170V438 V113G397 G355J897J400J1101J1100Key:Convenience CAN Hybrid CAN Extended CAN Infotainment CAN Sub-bus systems/private CAN MOST bus LVDS Dash panel insert CAN50Diagnostics CAN FlexRay Modular infotainment matrix CAN (MIB) LIN bus USB wires Ethernet connection Convenience CAN 2 Connect CAN R7U41R293E67J1060J525J1146J685J949Information Electronics Control Module 1 J794J898J285J587 J1121 Data Bus on Board Diagnostic Interface J533 Driver Assistance Systems Control Module J1121J1088R242J1089J853R243J794Ultrasonic sensors 1 - 12J769R212EX22R244J770J772EX23R245J428J1122J502J530R246J492J104J869Y7J706J234J1019J844J528J854J855J792J187J500G784J623J775J1135J217V475J1183C29J527669_121The FlexRay topology does not mirror the actual configuration of the control modules. The order of the control modules in the MOST ring in this illustration is also not identical to the actual sequence.51 Key:A6 A7 A27 A31 Battery, 48 V Voltage converter (48 V/12V) Right LED Headlamp Power Output Module 1 Left LED Headlamp Power Output Module 1 J866 J869 J897 J898 J926 J927 J938 J949 J1019 J1060 J1088 J1089 G65 G355 G397 G578 G784 H12 J104 J126 J136 J187 J217 J223 J234 J245 J285 J367 J386 J387 J400 J428 J453 J492 J500 J502 J521 J525 J527 J528 J530 J587 J605 J623 J685 J706 J764 J769 J770 J772 J775 J792 J844 J853 J854 J855 High Pressure Sensor Humidity Sensor Rain/Light Recognition Sensor Anti-Theft Alarm System Sensor Particulate Sensor Alarm Horn ABS Control Module Fresh Air Blower Control Module Memory Seat/Steering Column Adjustment Control Module Differential Lock Control Module Transmission Control Module Rear Spoiler Control Module Airbag Control Module Sunroof Control Module Instrument Cluster Control Module Battery Monitoring Control Module Driver Door Control Module Front Passenger Door Control Module Wiper Motor Control Module Control Module for Adaptive Cruise Control Multifunction Steering Wheel Control Module All Wheel Drive Control Module Power Steering Control Module Tire Pressure Monitoring Control Module Front Passenger Memory Seat Control Module Digital Sound System Control Module Steering Column Electronics Control Module Roof Electronics Control Module Garage Door Opener Control Module Selector Lever Sensor System Control Module Rear Lid Control Module Engine Control Module Front Information Display Control Head Passenger Occupant Detection System Control Module Electronic Steering Column Lock Control Module Lane Change Assistance Control Module Lane Change Assistance Control Module 2 Rearview Camera System Control Module Drivetrain Control Module Active Steering Control Module Automatic High Beam Assist Control Module Night Vision System Control Module Left Front Seat Belt Tensioner Control Module Right Front Seat Belt Tensioner Control Module J1100 J1101 J1122 J1135 J1146 J1169 J1170 Power Adjustable Steering Column Control Module Structure Borne Sound Control Module Ionizer Control Module Windshield Projection Head Up Display Control Module Driver Side Rear Door Control Module Passenger Side Rear Door Control Module Power Rear Lid Opening Control Module Control Module for Emergency Call Module and Communication Unit Rear Axle Steering Control Module Front Information Display Control Head 2 Control Module for Left Front Object Detection Radar Sensor Control Module for Right Front Object Detection Radar Sensor Windshield Washer Pump Control Module Fragrance Diffuser System Control Module Laser Distance Regulation Control Module Level Control System Compressor Electronics Mobile Device Charger 1 Close Range Communication Control Module Close Range Communication Control Module 2C Alternator C29 Starter Generator E1 E67 E265 EX22 EX23 Light Switch Driver Volume Control Rear A/C Display Control Head Switch Module in Instrument Panel, Center Center Console Switch Module 1J1183 NOx Sensor Control Module 3 MX3 MX4 MX13 N209 N210 N475 N477 R7 R212 R242 R243 R244 R245 R246 R293 U13 U41 V113 V388 V389 V390 V391 V438 V475 Y7 Left Tail Lamp Right Tail Lamp Center Tail Lamp Driver Lumbar Support Adjustment Valve Block Front Passenger Lumbar Support Adjustment Valve Block Valve Block 1 in Driver Seat Valve Block 1 in Front Passenger Seat DVD Player Night Vision System Camera Driver Assistance Systems Front Camera Front Peripheral Camera Left Peripheral Camera Right Peripheral Camera Rear Peripheral Camera USB Distributor Converter with Socket, 12 V-230 V USB Connection 1 Recirculation Door Motor Driver Seat Backrest Blower Fan Front Passenger Seat Backrest Blower Fan Driver Seat Cushion Blower Fan Front Passenger Seat Cushion Blower Fan Fresh Air Door Motor Transmission Fluid Auxiliary Hydraulic Pump 1 Automatic Dimming Interior Rearview Mirror52 A7 bus systemsThe bus systems used in the Audi A7 or similar to the Audi A8. The only new feature is Connect CAN, which connects Control Module for Emergency Call Module and Communication Unit  J949 to the gateway.Bus system Connect CANWire colorConfiguration Electrical bus systemData transfer rate 500 kbit/sFlexRayThe FlexRay topology of the Audi A7 is identical to that of the Audi A8. However, All Wheel Drive Control Module J492 may also be connected at branch 2A.J500 94 ΩJ492Key: J217 Transmission Control Module J492 All Wheel Drive Control Module J500 Power Steering Control Module J533 Data Bus on Board Diagnostic Interface2.6 kΩJ217 2.6 kΩBranch 2A J533 94 Ω669_183Reference For further information about FlexRay, refer eSelf-Study Program 970293, The 2019 Audi A8 Electrics and Electronics.53 Control modulesData Bus on Board Diagnostic Interface J533Brief description J533 (gateway) is installed under the rear seat. It is accessed with the VAS Scan Tool using Address word 0019. J533 performs the following functions: It is the LIN master for: Network system gateway. Controller for FlexRay bus. Diagnostic master. Energy manager for the 12 Volt electrical system. Energy manager for the 48 Volt electrical system. Interface for various connect services. J367 C J453 U13 Battery Monitoring Control Module. Alternator (12 Volt alternator). Multifunction Steering Wheel Control Module. Converter with Socket, 12 V-230 V.It is not a node of: CAN modular infotainment matrix (MIB). MOST bus.Special feature: The gateway manages the diagnostic firewall.It is a node of the following data bus systems: Hybrid CAN. Convenience CAN. Convenience CAN 2. Infotainment CAN. Dash panel insert CAN. Extended CAN. Connect CAN. FlexRay. Diagnostics CAN. Ethernet.Data Bus on Board Diagnostic Interface J533669_184 54 Vehicle Electrical System Control Module J519 (BCM1)Brief description The tasks of J519 include reading in numerous sensors and actuators, the exterior lights and the wipers. Many integrated functions, such as the activation of the seat heating, are also implemented. J519 also activates the air conditioning on the Audi A7. J519 can be accessed with the VAS Scan Tool using Address word 0009. Climate control functions are now accessed under this Address word.J519 performs the following functions: Exterior lighting master. Interior lighting master. Diagnostic gateway for the light control modules.J519 is the only node of convenience CAN 2. In addition, it is connected to Driver Assistance Systems Control Module  J1121 and the output modules for the headlights (output module 1 for headlight) via a private CAN. In addition, the J519 is the master control unit for numerous LIN slaves. Special feature: The interior lighting modules of the ambient lighting and the climate control motors can be connected both as a LIN series or parallel on the corresponding LIN branch. It is important to remember this when performing fault finding. Always consult the correct current flow diagram for the vehicle in its corresponding equipment version.Integrated functions: Parking. Parking aid. Ambient lighting. Activating the interior light modules. Climate control.669_185Vehicle Electrical System Control Module J51955 Comfort System Central Control Module J393 (BCM2)Brief description: Has diagnostic address 0046. Node of convenience CAN data bus. Has the following master functions: Central locking system. Immobilizer. LIN master for: LIN1: Anti-Theft Alarm System Sensor G578, Rear Spoiler Control Module J223. LIN2: Alarm Horn H12. LIN3: Power Rear Lid Opening Control Module J938, tail lights. Has master function for both near field communication control modules: Close Range Communication Control Module J1169. Close Range Communication Control Module 2 J1170.Further integrated functions Terminal management. Entry and start authorization. Central locking. Anti-theft alarm system. Activation of rear exterior lighting. Heated rear window. Turn signal control. Activation of rear roller blind. Rear lid release and luggage compartment lighting control. Tank filler flap locking. Power latching system for rear lid. Activation of sliding sunroof. Activation of