TECHNICAL DOCUMENTATION

SSP 990693 – The 2019 Audi A6 Introduction

PDFEN84 pages6 MB
SSP 990693 – The 2019 Audi A6 Introduction - PDF cover

This PDF is currently unavailable.

Read document text
The 2019 Audi A6 IntroductioneSelf-Study Program 990693 Audi of America, LLC Service Training Created in the U.S.A. Created 06/2018 Course Number 990693©2018 Audi of America, LLCAll rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC.Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Revision 2: Aug 8, 2018ii IntroductionPresentation Dimensions12 4BodyIntroduction Body assembly66 8Power unitsGasoline engines Engine/transmission combinations1111 12Power transmissionOverview1414Running gearOverview Axles and wheel alignment Steering system Brake system1616 17 19 20Electrics and electronicsIntroduction Layout of 12 Volt MHEV Starter Generator C29 Auxiliary Battery A1 48 Volt MHEV electrical system Networking Topology Exterior lighting Tail lights Convenience electronics on Audi A6 Central locking Interior lighting2222 24 26 27 30 32 34 38 46 48 50 53Climate controlOverview5454Safety and driver assist systemsPassive safety Driver assist systems5656 60Emergency assistFunction6969Infotainment and Audi connectIntroduction and overview of versions Sound Antennas7272 74 76Inspection and maintenance Knowledge assessment78 79iii The eSelf-Study Program (eSSP) teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. For further information about maintenance and repair work, always refer to the current technical literature.NoteReferenceiv IntroductionThe new Audi A6 is an impressive mix of elegance, high quality and advanced technology. The vehicle is even more comfortable, convenient and efficient than its predecessor thanks to the use of Mild Hybrid Electric Vehicle (MHEV) technology. All the connect services used in the 2019 A8 and 2019 A7 are included in 2019 A6 to make it into a fully networked vehicle. The Audi A6 ’s driver assist systems aren’t lagging behind its big sisters either. With its numerous driver assist systems, the Audi A6 is a safe and helpful companion on the road. In the interior, the Audi A6 has increased legroom and shoulder space. For the engines, Audi is using a 2.0l TFSI as standard for the Premium and Premium Plus models. The 3.0l V6 will be optional for the Premium and Premium Plus and standard for the Prestige line-up. All in all, a sporty exterior and a progressive interior featuring different equipment versions with something to suit every customer.670_002Learning objectives of this eSelf-Study Program: This eSelf-Study Program describes the design and function of the 2019 Audi A6. When completed, you will be able to answer questions on the following topics: ›› Engines available at market launch. ›› 12/48 Volt electrical system. ›› New running gear features. ›› New power transmission features. ›› New features of the infotainment systems.1 PresentationThe introduction of the 2019 Audi A6 marks the completion of the C8 product line. This eSelf-Study Program examines the similarities and differences of the A6 to the A7 and A8. For further information, please refer to the respective eSelf-Study Programs.670_034Audi A6 Sedan2 670_035Audi A7 Sportback670_036Audi A6 Avant (not for the North American Market at this time)3 DimensionsAudi A6 Sedan57.36 in (1457 mm)37.75 in (959 mm)64.17 in (1630 mm) 74.25 in (1886 mm)670_00363.66 in (1617 mm) 83.07 in (2110 mm)670_004m)54 1) m(1049 in41.38. 30 in(973mm)36.22 in (920 mm)115.11 in (2924 mm) 194.44 in (4939 mm)43.11 in (1095 mm)670_005426.61 in (676 mm) 15272)14673)15012)14363)1194 1050670_006Exterior dimensions and weightsLength Width (not incl. mirrors) Width (incl. mirrors) Height Front track Rear track Wheelbase Unladen weight Max. gross weight 194.44 in (4939 mm) 74.25 in (1886 mm) 83.07 in (2110 mm) 57.36 in (1457 mm) 64.17 in (1630 mm) 63.66 in (1617 mm) 115.11 in (2924 mm) 1825 2475Interior dimensions and other specificationsFront cabin width Front shoulder width Rear cabin width Rear shoulder width Load sill height Luggage compartment capacity Drag coefficient cw Capacity of fuel tank 60.11 in (1527 mm)2) 57.75 in (1467 mm)3) 59.09 in (1501 mm)2) 56.53 in (1436 mm)3) 26.61 in (676 mm) 18.71 cu ft (530 l) 0.24 19.28 gal (73 l)1) 2) 3)Maximum headroom Elbow room width Shoulder room widthAll dimensions refer to the unladen weight of the vehicle.5 BodyIntroductionThe body of the 2019 A6 is a composite construction using various materials. It is similar to the composition and construction of the 2019 A7. On the Audi A6 sedan, the rear roof cross member, the connection to the side roof frame and the D-pillar are fully manufactured from steel. The rear shelf is made of sheet aluminum.Key:Sheet aluminum Die-cast aluminum Aluminum section Ultra-high-strength steel (hot-formed) Modern high-strength steel High-strength steel Soft steel Composite steel/plastic6 670_143Reference For further information on the construction and structure of the body, please refer to eSelf-Study Program 990593 The 2019 Audi A7 Introduction.7 Body assemblyOn the topic of body assembly, it is also very clear that the 2019 A6 is related to the 2019 A7. For example, the Audi A6 also has semi-electric door locks. The construction of its instrument panel is also practically identical to the one in the Audi A7.SeatsEight-way power front seats with driver memory are standard equipment on the 2019 A6. They are heated and feature four-way power lumbar adjustment for the drive. Ordering the Warm Weather Package (Pr. no. PWZ (Premium Plus and Prestige only), provides four-way adjustable lumbar support for the front passenger seat and seat ventilation for both seats. Heated rear seats are available as part of the Cold Weather Package (Pr. no. PAW). A contour seat package is also available for Premium Plus and Prestige models. The A6 is equipped with a three-seat 40:20:40 split-folding rear seat. The backrest can only be released directly at the backrest in the interior of the vehicle. It can also be locked with the vehicle key so the luggage compartment cannot be accessed from the vehicle interior.Folding and lockable rear seat backrest8 Rear lidThere are two rear lid versions for the 2019 A6. The manual rear lid is opened via two mechanical extension springs. A hydraulic damper (left-side) has the task of reducing the speed of opening in the last 45° of the opening procedure. An optional electric rear lid is available for the A6. With this system, Rear Lid Motor 1 V444 moves the left rear lid hinge via a spindle drive. An extension spring on the right hinge supports the opening process on both the manual and electric systems. However, the spring installation position in the rear of the body will change depending on which system is installed.Extension springInstallation location for manual rear lid Hydraulic damper Rear Lid Drive Unit VX69 Installation location for electric rear lidExtension spring670_112Power latching systemThe power latching system for the rear lid has also been integrated into the rear lid lock on the 2019 A6. On the previous model, the striker on the lock carrier was moved downwards after the lock was engaged. However, Rear Lid Closing Aid Motor V382 now pulls the rotary latch of the rear lid lock into its end position after the initial catch has engaged.Rear Lid Closing Aid Motor V382670_1149 Operation of rear lid lockThe rear lid opens when the rear lid lock is actuated by Comfort Systems Central Control Module J393 via Rear Lid Central Locking System Motor V53. It is possible to release the rear lid manually in the event of an electrical failure. ›› The small cover in the rear lid trim in the luggage compartment must first be removed and the lever on the lock pressed upwards.Rear lid manual release with folding rear seat backrest670_11510 Power unitsGasoline enginesTorque/power curve of 3.0 ltr. TFSI engine EA839 Engine with code DLZA   Power in kW   Torque in Nm Torque/power curve of 2.0 ltr. TFSI engine EA888 Gen. 3 Engine with code DLHA   Power in kW   Torque in NmEngine speed [rpm]670_023Engine speed [rpm]670_108Features Engine code Type Capacity in cm Stroke in mm Bore in mm Number of valves per cylinder Firing order Compression ratio Power output Torque Fuel Turbocharging Engine management Maximum injection pressure in bar Emission control3Technical data DLZA V6 engine with 90° V angle 2995 89.0 84.0 4 1-4-3-6-2-5 11.2 : 1 340 hp (250 kW) at 5200 - 6400 rpm 369 lb ft (500 Nm) at 1370 - 4500 Premium unleaded Turbocharger with wastegate Bosch MD1 with OBD 250 One close-coupled catalytic converter, split into main and secondary catalytic converters, Lambda pr. before & after main cat. conv. LEV 3/Tier3 Mild hybrid (48V) DLHA Four-cylinder in-line engine 1984 92.8 82.5 4 1–3–4–2 9.6 : 1 252 hp (185 kW) at 5000 - 6500 rpm 273 lb ft (370 Nm) at 1600 - 4300 rpm Premium unleaded Turbocharger with wastegate Bosch MD1 with OBD 250 Close-coupled ceramic catalytic converter, Lambda probe before and after catalytic converterEmission standard ConceptLEV 3/Tier3 Mild hybrid (12V)Reference For further information about the engines used, please refer to eSelf-Study Program 920173, The Audi 3.0l V6 TFSI EA839 Engine and eSelf-Study Program 920163, Audi Third Generation 2.0l Engines. The construction of the fuel tank corresponds to the components of the 2019 Audi A7. For information, refer to eSelf-Study Program 990593, The 2019 Audi A7 Introduction..11 Engine/transmission combinationsGasoline engines 2.0 ltr. TFSI series 888 Gen. 3 3.0 ltr. TFSI series 8397-speed dual clutch gearbox 0CK DL382-7F7-speed dual clutch gearbox 0HL DL382+ -7ARear final drive 09R HL195.U1 M3) (quattro ultra)12 13 Power transmissionOverviewTwo power transmission options are available for the 2019 A6 in the North American Region at market launch. All 2.0l Premium and Premium Plus models will have S-tronic automatic transmissions and front wheel drive. All 3.0l models (Premium, Premium Plus and Prestige) will have S-tronic transmissions with All-wheel-drive. At market launch, all-wheel-drive models in the North American Region will be equipped with quattro with ultra technology.Manual release cable for parking lockSelector mechanism with shift-by-wire and park-bywire technology7-speed dual clutch transmission 0CK/ 0HL ›› Refer to Overview – Automatic transmissionFour-wheel drive coupling 0HLParking lock manual release with withdrawal lock ›› Since the end of 2017, the manual release mechanism with withdrawal lock has also been installed in the Audi Q5 and, since the beginning of 2018, in the B9 series vehicles.quattro with ultra technology The quattro with ultra technology four-wheel drive system can be used for engine torques of up to 500 Nm. ›› 7-speed dual clutch transmission 0HL with four-wheel drive coupling 0CX and rear final drive 09R. This combination was first used in the 2019 Audi A7.14 Overview – Automatic transmission only for NAR Depending on engine type, the following transmissions are available:PR no. G1C G1D1)Manufact. designation DL382-7F DL382+ -7AService designation 7-speed dual clutch transmission 0CK 7-speed dual clutch transmission 0HLMarketing designation S tronic S tronicDrive version Front-wheel drive quattro with ultra technologyOverview – Rear final drive The following rear final drive version is available at market launch:PR no. GH4 Manufact. designation HL195.U1 M Service designation Rear final drive 09R Combination with transmission 0HL quattro concept quattro with ultra technology1)Production no./equipmentThe illustration shows the drive train of the V6 3.0 ltr. TFSI with S tronic and the quattro four-wheel drive system with ultra technology.Rear final drive 09R ›› with dog-clutch670_083Special instructions apply when installing the propshaft15 Running gearOverviewThe running gear for the 2019 A6 has been completely redesigned when compared to the previous model. New technology and control systems adapted from the 2019 A8 and 2017 Q7 make it even more comfortable and dynamic. The front and rear axles are based on a high precision lightweight five-link design. Two suspension versions are available depending on model. Progressive steering, included as standard equipment, reduces the amount of steering effort required. The generously proportioned brake system offers substantial performance reserves for any corresponding driving situation. The 9th generation ESC system provides high-performance stability control for the vehicle.670_145The following suspension variants are available for the 2019 A6 at market introduction: Running gear with steel suspension and non-variable damping (1BA) This is the standard running gear. Sport running gear with steel suspension and non-variable damping (1BE) This suspension system is optional. The springs, dampers and anti-roll bars are set up for dynamic handling. The ride height is approximately 20 mm lower than version 1BA.16 Axles and wheel alignmentFront axleThe front axle is based on the proven design principle of the five-link suspension. A particular emphasis was placed on the lightweight construction. The MLBevo platform is used as the basis. Because the axle loads are similar, the front axle from the 2019 A7 has been used. Springs, dampers and anti-roll bars have been specially adjusted for use in the Audi A6.670_146Rear axleThe trapezium link rear axle used in the previous model has been replaced by a five-link axle which is largely a new development. The MLBevo platform is used as the basis. The axle for quattro is from the 2019 A7 . The springs and dampers have been adapted.Rear axle for quattro670_147The subframe and hub carrier have been newly developed for the front-wheel drive axle in addition to the concept for connecting the wheel bearing unit to the hub carrier. The wishbones, anti-roll bars and anti-roll bar couplings are from the quattro rear axle. The springs and dampers have been adapted.Rear axle for front wheel drive670_14817 Rear axleOn the rear axle for front-wheel drive, the method for securing the wheel bearing unit to the hub carrier has been changed from a bolt to a nut. The stub axle of the subframe now has an external thread. The hub carrier is geometrically identical to that of the 2018 Q5. The new method of securing the wheel bearing unit will be implemented in the Audi Q5 in the future and the hub carriers of both models will become standard.Wheel hub/wheel bearing unit670_149Hub carrierStub axle with external threadFlange nut for securing wheel hub/ wheel bearing unit on stub axleReference For further information on the construction of the axles and the wheel alignment adjustment options, please refer to eSelfStudy Program 990593, The 2019 Audi A7 Introduction.18 Steering systemThe steering system has been completely redeveloped compared to the previous model. The electromechanical power steering (EPS), the steering columns, the dynamic steering and the steering wheels are adapted from the 2019 A7.670_152Reference For further information about the steering components, refer to eSelf-Study Program 990593, The 2019 Audi A7 Introduction.19 Brake systemAs with the current MLBevo models, the brakes on the front and rear axles of the 2019 A6 have separate brake circuits and are not diagonally split. The brakes, brake servo, electromechanical parking brake and ESC are based on those of the 2019 A7.Brake system, front axleEngine Minimum wheel size Type of brakes Number of pistons Brake disc diameter Brake disc thickness 2.0 ltr. TFSI 17" Continental fixed caliper brakes 4 13.3 in (338 mm) 1.2 in (30 mm) 3.0 ltr. TFSI 18" ATE fixed caliper brakes 6 14.7 in (375 mm) 1.4 in (36 mm)Continental 4-piston fixed caliper brakes on front axleATE 6-piston fixed caliper brakes on front axle670_154670_155Brake system, rear axleEngine Minimum wheel size Type of brakes Number of pistons Brake disc diameter Brake disc thickness 2.0 ltr. TFSI 3.0 ltr. TFSI 17" TRW PC43HE EPBi Floating caliper brakes 1 12.9 in (330 mm) 0.86 in (22 mm)TRW PC43HE EPBi brakes for rear axle with electromechanical parking brake670_156Reference For further information, refer to eSelf-Study Program 990593, The 2019 Audi A7 Introduction.20 21 Electrics and electronicsIntroductionThe 2019 A6 is a Mild Hybrid Electric Vehicle (MHEV). In addition to the traditional battery, it is equipped with a lithium battery and starter-alternator. There are two system variations: ›› 12 Volt MHEV electrical system ›› 48 Volt MHEV electrical system The power for the drive train and the electrical energy are generated by the combustion engine. Fully electric driving is not possible with the Audi A6 MHEV. Vehicles with 4-cylinder engine are 12 Volt MHEVs. Vehicles with 6-cylinder engine are 48 Volt MHEVs and have a 48 Volt main electrical system.12 Volt MHEV electrical systemWiring junctions TV2 and TV3 with jump-start terminal Auxiliary Battery A1 In plenum chamber (front right) Relay and fuse carrier SR3 on lower section of right A-pillar12 Volt pinion starter12 Volt belt starter-alternatorFuse holder SF on instrument panel (left-side) Relay and fuse carrier SR1 in plenum chamber Relay and fuse carrier SR2 at foot rest (left-side)22 12 Volt main battery cableBattery A, 12V in rear right side panel670_045Relay and fuse carrier SR4 on control module rack in luggage compartmentReference For further information about mild hybrid functions, refer to eSelf-Study Program 970293, The 2019 Audi A8 Electrics and Electronics.23 Layout of 12 Volt MHEVA6 models with the 4-cylinder engine are 12 Volt MHEVs. In addition to the usual components, they have a 12 Volt lithium-ion battery and a 12 Volt starter-alternator.Starter BStarter Generator C29ConsumersStarter B The starter is a 12 Volt pinion starter. It is used to start the engine at engine oil temperatures of less than 113 °F (45 °C). The pinion starter meshes its pinion with the starter ring gear on the engine flywheel.Starter Generator C29 As the name implies, this component has two functions. When operated as an alternator, it provides the electrical system with electrical energy and charges both batteries. Its electric motor function is used to start the combustion engine when the engine oil temperature is above 113 °F (45 °C) and in start/stop mode. It is also able to support the combustion engine in certain driving situations. Because of the connection via the poly V-belt, an engine start using the starter-alternator is very quiet and almost completely free of vibrations.24 Battery AAuxiliary Battery A1670_046Battery A This battery is a 68Ah/380A AGM battery. It is installed behind the rear right side trim panel of the luggage compartment. Battery Monitoring Control Module J367 is installed on the negative terminal. Battery Interupt Igniter N253 is installed on the positive battery cable.Auxiliary Battery A1 The second battery uses lithium-ion technology and is connected in parallel to the AGM battery. It is activated via an internal relay of the AGM battery. It is installed in the plenum chamber (right-side) and can be accessed via a service flap in the plenum chamber cover. The auxiliary battery is installed in an aluminum housing to protect it from mechanical damage.Reference For further information about the dangers of lithium-ion technology, refer to eSelf-Study Program 970293, The 2019 Audi A8 Electrics and Electronics.25 Starter Generator C29General descriptionFor the 12 Volt MHEV, Starter-Generator C29 is a an aircooled 12 Volt belt starter-alternator. In its alternator function, it charges both batteries. The electric motor can be used both as a starter and to assist the engine. It is connected to the Engine Control Module J623 via a LIN data wire. As on any starter-alternator drive system, a special tensioner is used to ensure that the poly V-belt has a large wrap angle around the drive pulley.Starter-Generator C29670_047Technical dataDesignation Address Word Communication Terminal designations 12 Volt positive/negative Motor speed range Ratio (starter-alternator - engine) Nominal voltage in motor mode Nominal voltage in alternator mode Nominal power in motor mode (supporting engine for maximum 5 seconds) Maximum power in alternator mode (recuperation1) for maximum 30 seconds) Maximum continuous nominal power in alternator mode Maximum torque in motor mode Weight Starter-Alternator C29 None/engine control module is master LIN data wire to engine control module 30 / 31 1,500 rpm - 22,000 rpm Approximately 3:1 12 Volt 14.3 Volt Approximately 2 kW Approximately 6 kW Approximately 3 kW 60 Nm Approximately 21 lb (9.5 kg)1)Recuperation: Energy recovery. This means that the kinetic energy of the vehicle is converted into electric energy in overrun mode or under braking. 26 Auxiliary Battery A1General descriptionLithium ion Auxiliary Battery A1 houses additional components such as an internal battery control module and a relay. With the assistance of this relay, the positive terminal can be “switched off”. When the relay is open, there is then no voltage at the terminal. The lithium-ion battery is installed in an aluminum housing to protect it from mechanical damage. The 12 Volt lithium-ion battery is not actively cooled.670_048670_049Auxiliary Battery A1Protective metal housingBreather lineOperation of Auxiliary Battery A1 Auxiliary Battery A1 is connected in parallel to the AGM battery. Its relay is closed during the start procedure or shortly after. If the ignition is switched off, the relay is opened and A1 is once again disconnected from the electrical system. In certain operating conditions, such as for the duration of the continued operation of the radiator fans or the auxiliary pump, the relay may remain active after Terminal 15 has been deactivated. If an external battery charger is connected to the vehicle’s electrical system, the relay is closed after approximately 30 seconds (despite Terminal 15 being inactive) so Auxiliary Battery A1 can also be charged. In the event of an accident in which the airbag is triggered, Airbag Control Module J234 sends a signal to the control module in A1 and the relay is opened. A visual check and a classification of Auxiliary Battery A1 must be undertaken before it is removed.Technical dataDesignation Address Word Communication Terminal designations 12 Volt positive/negative Nominal voltage Number of cells Capacitance Usable energy Operating temperature Weight Cooling Installation location Auxiliary Battery A1 0080 Hybrid CAN node 30 / 31 12 Volt 4 11 Ah 0.15 kWh -22 °F to 149 °F (-30 °C to 65 °C) Approximately 11.0 lb (5 kg), without protective housing Air (passive) Plenum chamber (right-side), in protective housing27 Construction of batteryThe two halves of the housing are laser welded together. They are also sealed with liquid sealant. There is no provision for replacing battery cells or other individual components inside the battery.Battery housingBattery cellPrinted circuit boardBracket for battery cell (outer)Battery cellBracket for battery cell (inner)Bracket for bus barsNote When handling lithium-ion batteries, please observe all the legal requirements as well as all the safety notes and work instructions in the service literature and in the Guided Fault Finding programs in ODIS Service.28 Control moduleRelay Positive battery terminal Negative battery terminal670_050Bus barsBattery housingConnector29 48 Volt MHEV electrical systemThe 2019 A6 models with 6-cylinder engines are 48 Volt MHEVs. They require a voltage converter in addition to the 48 Volt lithium-ion battery and a 48 Volt starter-alternator. This converts the voltage from 48 Volts to 12 Volts to charge the 12 Volt battery. The installation locations of the batteries, the voltage converter, the 12 Volt pinion starter and the 48 Volt starter-alternator are, along with their functions and layout, identical to the components in the 2019 Audi A8.Wiring junctions TV2 and TV3 with jump-start terminal48 Volt positive wireRelay and fuse carrier SR3 on lower section of right A-pillar12 Volt pinion starter48 Volt belt starter-alternatorFuse holder SF on instrument panel (left-side)Relay and fuse carrier SR1 in plenum chamberRelay and fuse carrier SR2 at foot rest (left-side)30 12 Volt main battery cableVoltage Converter, 48 V/12 V A7 Battery A in rear right side panel670_051Battery, 48V A6 in spare wheel wellRelay and fuse carrier SR4 on control module rack in luggage compartmentReference For further information about mild hybrid functions, refer to eSelf-Study Program 970293, The 2019 Audi A8 Electrics and Electronics. .31 NetworkingInstallation locations of control modulesAlways refer to the current service literature for informa­ tion about the installation location and service procedures for control modules as well as instructions for installation and removal.J387 J1089A27A1R7 J1122J52 J794J500J792R242J234J245J77J428 J764 J898 J285 J527 J853J13J11A31J104 J623J1088 J869 J519 J386Key: A1 A6 A7 A27 A31 J104 J136 J187 J234 J245 J285 Auxiliary Battery Battery, 48 V Voltage converter (48 V/12V) Output module 1 for right LED headlight Output module 1 for left LED headlight ABS Control Module Memory Seat/Steering Column Adjustment Control Module Differential Lock Control Module Airbag Control Module Sunroof Control Module Instrument Cluster Control Module J386 J387 J393 J428 J500 J502 J519 J521 J525 J527 J533 J605 J623 J764 J769 Driver Door Control Module Front Passenger Door Control Module Comfort System Central Control Module Adaptive Cruise Control Module Power Steering Control Module Tire Pressure Monitoring Control Module Vehicle Electrical System Control Module 1 Front Passenger Memory Seat Control Module Digital Sound System Control Module Steering Column Electronics Control Module Data Bus On Board Diagnostic Interface Rear Lid Control Module Engine Control Module Electronic Steering Column Lock Control Module Lane Change Assistance Control Module32 J927A7J76921 J187 J393A6 J533 J77275R86 J94936121 J502J605J525J770J926670_052J770 J772 J775 J792 J794 J853 J869 J898 J926 J927 J949 J1088 J1089 J1121 J1122 Lane Change Assistance Control Module 2 R7 Rearview Camera System Control Module R86 Drivetrain Control Module R242 Active Steering Control Module Information Electronics Control Module 1 Night Vision System Control Module Structure-Borne Sound Control Module Windshield Projection Head Up Display Control Module Driver Side Rear Door Control Module Passenger Side Rear Door Control Module Control Module for Emergency Call Module and Communication Unit Control Module for Left Front Object Detection Radar Sensor Control Module for Right Front Object Detection Radar Sensor Driver Assistance Systems Control Module Laser Distance Regulation Control ModuleDVD Player Cellular Telephone Amplifier Driver Assistance Systems Front Camera33 TopologyJ926 J386J927J387J605N209J136J764Diagnostic connectorN475J245J453A61)N210J521J392J367A71)N477C3)A12)H12G578Comfort System Central Control Module J393G65Control motors 1 - 2Vehicle Electrical System Control Module J519A31A27J938Heater controls 1 - 4 ­MX3E265MX4Control motors 1 - 15Ambient light 1 - 15J866MX5Ambient light 16 - 30V388 V390MX6Ambient light 31 - 45V389 V391 E1J126V438 V113G397 G355J897J400J1101G935Key:Convenience CAN Hybrid CAN Extended CAN Infotainment CAN Sub-bus systems/private CAN MOST bus LVDS Instrument panel insert CAN Diagnostics CAN FlexRay Modular infotainment matrix CAN (MIB) LIN bus USB wires Ethernet connection Convenience CAN 2 Connect CAN34 R7U41R293E67J1060J525J1146J685J949Information Electronics Control Module 1 J794 J285J898J587 J1121 Data Bus On Board Diagnostic Interface J533 Driver Assistance Systems Control Module J1121J1088R242J1089J853R243 J794 EX22 R244Ultrasonic sensors 1 - 12J769R212J770J772EX23R245J428J1122J502J530R246J492J104J869Y7J706J234J844J528J854J855J792J187J500J623J775J217V475C291)C292)J527670_05348 Volt MHEV only 12 Volt MHEV only 3) Vehicles without an additional lithium-ion battery only1) 2)For presentation reasons, the FlexRay topology does not mirror the actual configuration of the control units. The order of the control units in the MOST ring in this illustration is also not identical to the actual sequence.35 Key:A1 Auxiliary Battery A61) Battery, 48 V A71) Voltage Converter (48 V/12V) A27 Right LED Headlamp Power Output Module 1 A31 Left LED Headlamp Power Output Module 1 C Alternator C29 Starter Generator E1 Light Switch E67 Driver Volume Control E265 Rear A/C Display Control Head EX22 Switch Module in Instrument Panel, Center EX23 Center Console Switch Module 1 G65 High Pressure Sensor G355 Humidity Sensor G397 Humidity Sensor G578 Anti-Theft Alarm System Sensor G935 Exterior Air Quality and Humidity Sensor H12 Alarm Horn J104 ABS Control Module J126 Fresh Air Blower Control Module J136 Memory Seat/Steering Column Adjustment Control Module J187 Differential Lock Control Module J217 Automatic Transmission Control Module J234 Airbag Control Module J245 Sunroof Control Module J285 Instrument Cluster Control Module J367 Battery Monitoring Control Module J386 Driver Door Control Module J387 Front Passenger Door Control Module J392 Rear Sunroof Control Module J400 Wiper Motor Control Module J428 Adaptive Cruise Control Module J453 Multifunction Steering Wheel Control Module J492 All Wheel Drive Control Module J500 Power Steering Control Module J502 Tire Pressure Monitoring Control Module J521 Front Passenger Memory Seat Control Module J525 Digital Sound System Control Module J527 Steering Column Electronics Control Module J528 Roof Electronics Control Module J530 J587 J605 J623 J685 J706 J764 J769 J770 J772 J775 J792 J844 J853 J854 J855 J866 J869 J897 J898 J926 J927 J938 J949 J1060 J1088 J1089 J1101 J1122 J1146 MX3 MX4 MX5 MX6 Garage Door Opener Control Module Selector Lever Sensor System Control Module Rear Lid Control Module Engine Control Module Front Information Display Control Head Passenger Occupant Detection System Control Module Electronic Steering Column Lock Control Module Lane Change Assistance Control Module Lane Change Assistance Control Module 2 Rearview Camera System Control Module Drivetrain Control Module Active Steering Control Module Automatic High Beam Assist Control Module Night Vision System Control Module Left Front Seat Belt Tensioner Control Module Right Front Seat Belt Tensioner Control Module Power Adjustable Steering Column Control Module Structure-Borne Sound Control Module Ionizer Control Module Windshield Projection Head Up Display Control Module Driver Side Rear Door Control Module Passenger Side Rear Door Control Module Power Rear Lid Opening Control Module Control Module for Emergency Call Module and Communication Unit Front Information Display Control Head 2 Control Module for Left Front Object Detection Radar Sensor Control Module for Right Front Object Detection Radar Sensor Fragrance Diffuser System Control Module Laser Distance Regulation Control Module Mobile Device Charger 1 Left Tail Lamp Right Tail Lamp Left Tail Lamp 2 Right Tail Lamp 236 Key:N209 N210 N475 N477 R212 R242 R243 R244 R245 R246 R293 Driver Lumbar Support Adjustment Valve Block Front Passenger Lumbar Support Adjustment Valve Block Valve Block 1 in Driver Seat Valve Block 1 in Front Passenger Seat Night Vision System Camera Driver Assistance Systems Front Camera Front Peripheral Camera Left Peripheral Camera Right Peripheral Camera Rear Peripheral Camera USB Distributor U41 V113 V388 V389 V390 V391 V438 V475 Y7 USB Connection 1 Recirculation Door Motor Driver Seat Backrest Blower Fan Front Passenger Seat Backrest Blower Fan Driver Seat Cushion Blower Fan Front Passenger Seat Cushion Blower Fan Fresh Air Door Motor Transmission Fluid Auxiliary Hydraulic Pump 1 Automatic Dimming Interior Rearview MirrorBus systems used in the Audi A6The bus systems used in the 2019 A6 are the same as the 2019 A8 with the exception of the new Connect CAN. It connects Control Module for Emergency Call Module and Communication Unit J949 to the Gateway.Bus system Connect CANWire colorConfiguration Electrical bus systemData transfer rate 500 kbit/sFlexRayThe FlexRay topology of the Audi A6 is identical to that of the 2019 A8. However, All Wheel Drive Control Module J492 may also be connected at branch 2A.J500 94 ΩJ492Key: J217 J492 J500 J533 Automatic Transmission Control Module All Wheel Drive Control Module Power Steering Control Module On Board Data Bus Diagnostic Interface (Gateway)2.6 kΩJ217 2.6 kΩBranch 2A J533 94 Ω670_054Reference For further information about FlexRay, refer to eSelf-Study Program 970293, The 2019 Audi A8 Electrics and Electronics.37 Exterior lightingHeadlightsLED headlights (PR No.: 8IT + 8G1/8G0) Available as ECE1) and SAE2) version. The illustration shows the left headlight in the ECE1) version.670_055Low beam, 6 LEDsHigh beam, 5 LEDsXXXXXX XXXXXFront left turn signal bulbLighting functions ›› Daytime running light ›› Side light ›› Low beam ›› High beam ›› All-weather light ›› Turn signal ›› Side marker light (SAE only2), not illustrated)Special features of the lighting functions The daytime running lights (“turn signals during the day”) and the marker light (“turn signals at night) remain active while the turn signals are active. This applies to both the ECE1) and the SAE2) versions.Adjusting headlights for driving on other side of road It is not necessary to adjust the headlights. The legal requirements are met without additional measures.1) 2)ECE = for the European market SAE = for the North American market38 An LED headlight is available as standard for the Audi A6. With one exception, all lighting functions are performed by LEDs. The turn signal is produced by a 24 W bulb. The LEDs for the low beam and the high beam are installed in a projection module. In the top row, the low beam is generated by 6 LEDs.In the bottom row, 5 LEDs are used for the high beam function. Thanks to its comparatively simple construction, the LED headlight is the lightest of the three headlights available for the Audi A6 with a weight of approximately 10 lb (4.5 kg).Output module for LED headlightHeadlight range control motor670_056LED module with heat sink The projection lens remains in the headlight if the LED module is replaced.Equipment The LED headlights can be combined with the high beam assist as an option. A headlight washer system is also available optionally. Service The control module installed on the outside of the headlight housing, the bulb module for the turn signal, the LED module, and the headlight range control motor (ECE1) only) can be replaced in the event of a defect. The LED module and the control motor can only be replaced on the ECE1) version. In the event of damage to the upper and inner headlight attachments, repair tabs can be attached to the headlight housing.Headlight range adjustment The LED headlights are equipped with automatic dynamic headlight range adjustment.It is very important to keep the inside of the headlight as clean as possible when replacing components inside of the headlight. It is also recommended to use the ESD antistatic mat VAS 6613 to prevent electrostatic discharge. Wear gloves and avoid touching components to protect the parts of the optical system relevant to lighting. Replacing the LED module is a very delicate procedure and requires precise skill from the Technician.39 Smart matrix LED headlights (PR No.: 8IT + 8G4) Available as ECE1) and SAE2) version. The illustration shows the left headlight in the ECE1) version.670_057Low beam, 8 LEDsMatrix high beam, 7 LEDsXXXXXXXX XXXXXXXLighting functions ›› Daytime running light ›› Marker light ›› Low beam ›› Matrix beam high beam ›› Turn signal ›› All-weather light ›› Turning light ›› Intersection light (in combination with navigation system) ›› Highway light ›› Cornering light ›› Side marker light (SAE only2), not illustrated)Special features of the lighting functions Turn signals during the day: On the ECE1) version, the daytime running light is dimmed to marker light level when the turn signal is activated. On the SAE2) version, the daytime running lights are switched off during the turn signal procedure. Turn signals at night: On both the ECE1) and SAE2) versions, the marker light remains active according to the legal requirements for the North American market.1) 2)40ECE = for the European market SAE = for the North American market The smart matrix LED headlight has a one-row matrix high beam. According to the traffic situation detected, 7 LEDs can be switched off individually to avoid blinding vehicles ahead or oncoming vehicles.The low beam is generated by 8 LEDs. On this headlight version, all lighting functions are performed by LEDs.Output module for LED headlightHeadlight range control motor670_058LED module with heat sink The projection lens remains in the headlight if the LED module is replaced.Headlight range adjustment The smart matrix LED headlights are equipped with automatic dynamic headlight range adjustment.Equipment The Audi A6 with smart matrix LED headlights is installed with a headlight washer system as standard.Service The control module is installed to the outside of the headlight housing, the LED module (one assembly group for the low beam and one assembly group for the high beam) and the headlight range control motor can be replaced in the event of a defect. The LED module and the control motor can only be replaced on the ECE1) version. In the event of damage to the upper and inner headlight attachments, repair tabs can be attached to the headlight housing. It is very important to keep the inside of the headlight as clean as possible when replacing components in the inside of the headlight. It is also recommended to use the ESD anti-static mat VAS 6613 to prevent electrostatic discharge. Wear gloves and avoid touching components to protect the parts of the optical system relevant to lighting. Replacing the LED modules is a very delicate procedure and requires precise skill from the Technician.41 HD matrix LED headlights (PR No.: 8IT + 8G5) Available as ECE1) and SAE2) version. The illustration shows the left headlight in the ECE1) version.670_059Matrix high beam Top row, 16 LEDs Matrix high beam Bottom row, 16 LEDsXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXLighting functions ›› Dynamic daytime running light ›› Dynamic marker light ›› Low beam ›› Matrix beam high beam ›› Dynamic turn signal ›› All-weather light ›› Turning light ›› Highway light ›› Cornering light ›› Intersection light (in combination with navigation system) ›› Side marker light (SAE only2), not illustrated)Special features of the lighting functions Turn signals during the day: On the ECE1) version, the daytime running light is dimmed to marker light level when the turn signal is activated. On the SAE2) version, the daytime running lights are switched off during the turn signal procedure. Turn signals at night: The marker light remains active on both the ECE1) and SAE2) versions. The turn signal is dynamic. The marker light and daytime running light are also dynamic and are activated at different moments as part of the “coming/leaving home” function.1) 2)ECE = for the European market SAE = for the North American market42 The Audi designation for the two-row matrix headlights first introduced in the Audi A8 is HD (high definition) matrix LED headlights, or matrix 2.0. In this system, the matrix high beam is generated by two rows of LEDs containing 16 LEDs each. With 64 LEDs in the two headlights, it is therefore possible to achieve a very finely graded reduction in the light to avoid blinding other road users.Because of its complex construction, the HD matrix LED headlight is the heaviest of the three headlight versions available for the Audi A6.Output module for LED headlightHeadlight fanPrinted circuit board670_060Headlight range control motorHeadlight range adjustment The HD matrix LED headlights are equipped with automatic dynamic headlight range adjustment.Equipment The Audi A6 with HD matrix LED headlights are installed with a headlight washer system as standard.Service The control module installed on the outside of the headlight housing, the printed circuit board, the fan, and the headlight range control motor can be replaced in the event of a defect. In the event of damage to the upper and inner headlight attachments, repair tabs can be attached to the headlight housing. It is very important to keep the inside of the headlight as clean as possible when replacing components in the inside of the headlight. It is also recommended to use the ESD anti-static mat VAS 6613 to prevent electrostatic discharge. Wear gloves and avoid touching components to protect the parts of the optical system relevant to lighting. Replacing the printed circuit board and the fan is a very delicate procedure and requires precise skill from the Technician.43 Activation of matrix LED headlights Illustration for left headlightLeft Front Headlamp MX1 Humidity Sensor G397 Low beam Matrix beam high beam All-weather light Light Switch E1 Turning light Laser light Daytime running light Vehicle Electrical System Control Module J519 Left LED Headlamp Power Output Module 1 A31 Side light Background light Dynamic turn signal Side marker light (SAE2)) Headlight range control FanDriver Assistance Systems Control Module J1121Driver Assistance Systems Front Camera R242670_061Key: Convenience CAN 2 FlexRay Sub-bus systems LVDS LIN busActivation Vehicle Electrical System Control Module J519 communicates with Left/Right LED Headlamp Power Output Module 1 A31/A37 via a sub-bus system. These output modules activate all lighting functions, the headlight range control motors and, on the matrix headlights, the fan(s). High beam assist Together with Driver Assistance Systems Front Camera R242, Driver Assistance Systems Control Module J1121 is responsible for the high beam assist function. If the camera detects oncoming vehicles or vehicles ahead, it passes this information on to Driver Assistance Systems Control Module J1121. J1121 calculates which LEDs in the matrix headlights need to be switched off to avoid blinding other road users. This information is sent to the output modules via the sub-bus system. On the LED headlights, only two conditions are possible: “high beams on” or “high beams off”. The control modules are capable of self-diagnosis and can be accessed via Address Word 00D6/00D7. The illustration shows an example of the communication paths and the components involved. The activation process inside the headlight is not relevant for repairs and therefore not shown specifically.2)SAE = for the North American market44 Calibrating matrix LED headlights Calibration of the matrix headlights is always required after the following work: ›› Headlight position was changed (removed/installed, securing bolts loosened). ›› Headlights were adjusted. ›› Drivetrain Control Module J775 was recalibrated or renewed. ›› Driver Assistance Systems Control ModuleJ1121 was replaced. ›› Left Rear Level Control System Sensor G76, Right Rear Level Control System Sensor G77, Left Front Level Control System Sensor G78 or Right Front Level Control System Sensor G289 has been renewed. ›› The event memory contains the entry "No or incorrect basic setting / adaption".Aligning reference segment As with the first generation of the matrix LED headlight used in Europe, reference segment is measured using the headlight adjustment unit VAS 621 001 as the first step of the calibration process. The deviation value is then sent to Driver Assistance Systems Control Module J1121 with the help of the Scan Tool. The yellow line on the image shows which edge the reference segment is being aligned to. In this example, a horizontal deviation of +26 minutes has been determined. When the low beams are adjusted, the height of the matrix beam high beam module is also corrected due to the inner layout of the HD matrix LED headlight. When the matrix beam high beams are then calibrated, it is sufficient to determine the horizontal deviation of the reference segment. This means that the calibration procedure for the one-row smart matrix and the two-row HD matrix LED headlight is the same.The illustration shows the reference segment of the left matrix LED headlightVH: +26´H670_062Note Up-to-date service literature must be used for all checking, repair and adjustment work.45 Tail lightsGeneral descriptionThe 2019 A6 uses 2 taillights on each side of the vehicle. One is located in the quarter panel and one in the outer edge of the trunk lid.. Versions There are 3 possible versions of the tail lights used in the A6. In the SAE market only two are used. ›› LED tail lights (low) ›› LED tail lights (mid) with dynamic turn signals ›› LED tail lights (high) with dynamic turn signals and dynamic tail lights PR No. 8SK (ECE1) only) PR No: 8SP (ECE1) and SAE2)) PR No: 8SQ (ECE1) and SAE2))The illustration shows the 8SQ tail lights in the ECE1) version.670_063Left tail light MX3Left tail light 2 MX5The tail light versions are geometrically identical. The design varies between the ECE1) and SAE2) versions. There are differences in the functions and the activation of the tail lights. The highest equipment version (PR no. 8SQ) is equipped with dynamic turn signals and dynamic tail lights.Dynamic tail light means that: The tail lights are lit gradually when Terminal 15 is activated. The tail light LEDs are activated as part of the “coming/leaving home” function.Activation The tail lights are activated by Comfort System Central Control Module J393. On the 8SQ version, the tail lights are connected to J393 via a LIN data wire in addition to the discrete wires. On this tail light version, the dynamic turn signal and dynamic tail light commands are sent via the LIN data wire.1) 2)ECE = for the European market SAE = for the North American market46 High-mounted brake lightsThe high-mounted brake light is located inside the vehicle behind the rear window. 18 LEDs with a power output of 3.2 W support the brake light function. In the event of a fault, the high-level brake light must be replaced as a complete unit.High-Mounted Brake Lamp Bulb M25670_06447 Convenience electronics on Audi A6The 2019 A6 offers various convenience functions. Most were adapted from the 2019 Audi A8.Some of the equipment and features listed are optionally available separately or in a package. Please consult the 2019 A6 ordering guide for the latest and most complete information. ›› Interior mirror: auto-dimming interior rear view mirror (frame-less) with compass. ›› Rear trunk lid with electric open/close function. ›› Locking systems: All vehicles are equipped with radio remote keys.. ›› Garage door opener with GPS support (when the vehicle nears the stored location, a corresponding message appears to trigger the procedure for sending a signal). ›› Seating comfort: Front seats with memory function; Front seat and outer rear seat heating; Seat ventilation and seat massage for front seats only.›› Electric steering column adjustment. ›› Analog instrument cluster or optional Audi virtual cockpit. ›› Head-up display (as optional equipment).Automatic Dimming Interior Rearview Mirror Y7Audi virtual cockpitIlluminated quattro badgeAmbient lighting in front door670_032Individual contour seats (front)Ambient lighting Center console48670_033 Instrument clusterTwo different instrument clusters are used for the Audi A6 : ›› The standard instrument cluster. ›› The optional Audi virtual cockpit. The driver information system in the analog instrument cluster is a high-resolution 7” color display. The following can be displayed: ›› Speed (digital speedometer). ›› Time. ›› Mileage. ›› Outside temperature. ›› Fuel level warning with remaining range. ›› Gear-change indicator in TIP mode. ›› Current radio station or music track. ›› Radio and media lists. ›› Telephone menu. ›› Information from the navigation system and messages from the driver assist systems (if installed). The information provided by the on-board computer’s short-term and long-term memory includes average and current fuel consumption, remaining range, average speed, driving time and distance covered. The integrated efficiency program helps the driver to drive economically with overviews of consumption data and economy tips, including the rest recommendation. The Audi virtual cockpit is an innovative, fully digital instrument cluster with the flexibility to display the relevant information according to the driver’s requirements and as needed. The Audi connect services, for example, can also be displayed. The VIEW button on the multi-function steering wheel allows the driver to switch between two different-sized versions of the round instruments. The display with small instruments allows large, clear graphics to be displayed by the on-board computer and the MMI. It is possible to display the navigation map as a 3D terrain model on the high-resolution 12.3” Full HD color display.Analog instrument cluster 7” driver information system displayWarning lamps in speedometer670_020Row of warning lampsAudi virtual cockpitRow of warning lampsCoolant temperature gauge (LED 1-7 in white; LED 8 = 266 °F (130 °C) in redFuel gauge (8 white LEDs)670_02149 Central lockingAudi advanced keyThe central locking system in the 2019 A6 is similar to the system in the 2019 A7.Unlocking the vehicle: A vehicle key must be within the detection area of the vehicle door. If someone reaches into the door handle, the corresponding exterior door handle contact sensor (for example, Driver Exterior Door Handle Touch Sensor G415) reports this to Comfort System Central Control Module J393. J393 interrogates the vehicle key. This transmits its data back to the central locking system antenna, which is on the printed circuit board of J393. If the key is detected as an authorized vehicle key, J393 transmits a command to the door control modules to unlock the doors via the convenience CAN bus.Locking the vehicle: A coded vehicle key must also be in the detection area when the vehicle is being locked. If the driver presses the locking sensor on the exterior door handle (for example, Driver Exterior Door Handle Touch Sensor G415), this signal is transmitted to J393 via the CAN bus. This queries whether there is actually an authorized key in the detection area. After the key has successfully transmitted its data to J393 via a radio signal, J393 sends the locking command to the corresponding door control modules.Central locking system diagramData Bus On Board Diagnostic Interface J533Electronic Steering Column Lock Control Module J764Comfort System Central Control Module J393E408G415R137G416R138G417R139Key:Convenience CAN Sub-bus systems/private CAN Discrete wiresG418R200R201670_028E408 G415 G416 G417 G418 50Access/Start Authorization Button Driver Exterior Door Handle Touch Sensor Front Passenger Exterior Door Handle Touch Sensor Left Rear Exterior Door Handle Touch Sensor Right Rear Exterior Door Handle Touch SensorR137 R138 R139 R200 R201 Access/Start System Antenna in Luggage Compartment Access/Start System Antenna 1 in Vehicle Interior Access/Start System Antenna 2 in Vehicle Interior Left Access/Start Authorization Antenna Right Access/Start Authorization Antenna As soon as the central locking system is woken by a capacitive proximity sensor, a query signal is transmitted to the remote control key in the low frequency (LF) range. The remote control key decodes the low frequency signal and transmits its coding of the high frequency (HF) signal to the central locking system antenna and on to Comfort System Central Control Module J393. If the data received are correct/if an authorized vehicle key is detected, J393 gives the unlocking command to the corresponding door control unit.Block and schematic diagram of transmission frequencies for central locking systemComfort System Central Control Module J393HF signalFront Access/Start Authorization Antenna R376 Front Access/Start Authorization Antenna R376 is installed at the front of the front bumper. R376 is needed to ensure that communication in the front area of the vehicle is possible ― the key needs to be able to determine its position in relation to the vehicle. MVs are available for R376 and can be viewed using the VAS Scan Tool.J393Remote control keyLF signalExterior door handle sensors670_029R376R138R201G750 G760Installation location: in front bumperG415 R200 G417R137670_030Key:G415 G417 G750 G760 R137 R138 R200 R201 R376 Driver Exterior Door Handle Touch Sensor Left Rear Exterior Door Handle Touch Sensor Power Rear Lid Opening Sensor Power Rear Lid Opening Sensor 2 Access/Start System Antenna in Luggage Compartment Access/Start System Antenna 1 in Vehicle Interior Left Access/Start Authorization Antenna Right Access/Start Authorization Antenna Front Access/Start Authorization AntennaFront Access/Start Authorization Antenna R376670_03151 Comfort System Central Control Module J393On the Audi A6, J393 is installed in the underbody of the luggage compartment, immediately behind the rear seat backrests. J393 is installed on control module rack. As the base carrier, the control module rack comes in two different versions. Depending on the vehicle’s equipment, a small base carrier or the larger one shown in the illustration is used. The components attached include: ›› Relay and fuse carrier SR4. ›› Comfort System Central Control Module J393. ›› A 12 Volt power distributor. ›› Control Module for Emergency Call Module and Communication Unit J949. ›› Cellular Telephone Amplifier R86. ›› Differential Lock Control Module J187.Installation locationRelay and fuse carrier SR4 12 Volt power distributor Comfort System Central Control Module J393 Differential Lock Control Module J187Towing Recognition Control Module J345 (not for the North American Region) J345 Control Module for Emergency Call Module and Communication Unit J949670_044Cellular Telephone Amplifier R86Parking Heater Radio Receiver R64 (not for the North American Region) R64Windshield Defogger Control Module J505 (not for the North American Region) J50552 Interior lightingThere are two interior lighting packages available for the 2019 A6 depending on model: ›› Ambient lighting package QQ1. ›› Contour ambient lighting package QQ2. Ambient lighting package QQ1 includes all the important lighting functions: ›› Both LED roof modules (front and rear, capacitive lights). ›› Make-up lights. ›› Entry lights (front and rear). ›› Illuminated interior door handles (front and rear). ›› Illuminated center console storage compartment. ›› Glove box light. ›› Footwell lights (front and rear). ›› Two luggage compartment lights . ›› Ambient door panel lighting for doors (front/rear). ›› Surround lighting from exterior door handles (front/ rear). ›› Ambient lighting in instrument panel. An additional interactive and individual color profile is controlled by the Audi drive select modes. A large number of colors are available with the individual color profile. The color adjustments are made separately for contour and ambient lighting. Vehicles equipped with the QQ2 contour ambient lighting package (which includes most of the QQ1 package) have the following items lit with LEDs featuring six pre-defined color profiles: ›› Door pockets (front/rear). ›› Door contour lighting (front/rear). ›› Ambient door panel lighting for doors (front/rear). ›› Ambient lighting for front center console. ›› Contour lighting for front center console. ›› Contour lighting with illuminated quattro badge or illuminated Audi rings (on front-wheel drive vehicles) in the instrument panel on the passenger side. ›› Ambient lighting for instrument panel.670_022Light strips from the ambient/contour ambient lighting packages are used in the inner doors, the instrument panel and the center console.53 Climate controlThe new technical features which were introduced with the 2019 Audi A8 are continued in the 2019 Audi A6. Many of the new technical features introduced with the 2019 A8 climate control system are continued with the 2019 A6. For the North American market, the 2019 A8 will use refrig­ erant R-1234yf at vehicle introduction.OverviewFragrance diffuser systemA fragrance diffuser system with two different fragrances is offered for the 2019 A6. The fragrances are kept in cylindrical vials in Fragrance Diffuser System Functional Unit GX43. A small blower guides the fragrance from the vial into the outer front air outlets. In addition to the fragrance type, four levels of intensity can be selected.Air ionization systemAn air ionization system is used in the Audi A6 to improve the air quality. The air ionization system works by negatively charging a limited number of air particles. They are distributed in the vehicle interior via the side and front air outlets. These anions neutralize the dust and similar very small particles that they attract.Back massageA back massage function is offered for the front seats of the 2019 A6 depending on model. The following seven massage programs can be selected. ›› Wave ›› Pulse ›› Stretch ›› Rest ›› Shoulder ›› Activation ›› RevitalizationClimate control operation in front of vehicleClimate control operation is now implemented via two touch displays communicating with Vehicle Electrical System Control Module 1 J519. A separate Climate Control Module J255 is no longer needed. Communication between the touch screens and J519 is via the LIN bus system. The main new feature regarding the look and feel of the operation are the two displays. The upper MMI display and the lower touch display are both installed centrally in the instrument panel and the center console. The air conditioner functions in the top MMI display can be accessed via the Car menu. The MMI display can be used, depending on the optional equipment. To select the following functions and their settings: ›› Ionization ›› Perfume ›› Steering wheel heating ›› Synchronization for driver/passenger side ›› Climate control for rear passengers/for rear ›› Climate control (A/C MAX, A/C OFF, A/C eco)670_041Overview of MMI display (Climate control operation)Car · A/C54 Climate control in rear of vehicleDepending on the equipment version, two different operating units may be available in the rear. ›› 3-zone climate control Rear operating unit with digital temperature display and buttons for seat heating. ›› 4-zone air conditioning Rear touch operating unit including air conditioner regulation and seat heating, permanently installed in the center console.3-zone climate control Rear A/C Display Control Head E265 is used for controlling the system in the rear of the vehicle. The seat heating can be set on this operating unit in addition to the temperature and the blower speed.670_0424-zone climate control The optional Rear A/C Display Control Head E265 is equipped with a sensory surface. It is operated by touch. The following settings can be made: ›› Temperature ›› Blower speed ›› Air distribution ›› Automatic climate control ›› Climate control on/off ›› Seat heating670_04355 Safety and driver assist systemsPassive safetyThe following pages provide an overview of the occupant protection system in the 2019 A6.Airbags in vehicleKnee airbag (passenger side) Passenger airbagDriver airbagKnee airbag (driver side)Components›› Airbag control module ›› Adaptive driver airbag ›› Adaptive passenger airbag (two-stage passenger airbag) ›› Front side airbags ›› Side airbags for seat row 2 ›› Curtain airbags ›› Knee airbags ›› Crash sensors for front airbags ›› Front belt retractors with pyrotechnic belt tensioners ›› Front belt retractors with electric belt tensioners ›› Front belt retractors with switchable belt force limitersFront side airbag›› Belt retractors for seat row 2 with pyrotechnic belt tensioners for driver and passenger side ›› Belt retractors for seat row 2 with electric belt tensioners for driver and passenger side ›› Front lap belt tensioners for driver and passenger sides ›› Seat belt warning for all seats ›› Seat-occupied recognition system in passenger seat ›› Seat-occupied recognition system for seat row 2 ›› Front passenger airbag warning lamp (OFF and ON) ›› Seat position detection for driver and passenger ›› Battery isolator, 12 Volt electrical system ›› Battery isolator, 48 Volt sub-systemReference For further information on the airbag control unit J234 and Audi pre sense, please refer to eSelf-Study Program 990493, The 2019 Audi A8 Introduction.56 Front side airbagCurtain airbag, driver and passenger sideSide airbag for seat row 2Side airbag for seat row 2670_037Note The images in the “Passive safety” chapter are schematic diagrams and are provided to aid understanding.57 System overviewThe system overview shows components which depend on the market and the vehicle equipment.670_02658 Additional equipmentEquipment may vary due to the different demands and legal requirements that are made of vehicle manufacturers in the markets.Key to diagram on Page 46:E24 E25 F390 F391 F392 G128 G177 G178 G179 G180 G256 G257 G283 G284 G551 G552 G553 G554 Driver Seat Belt Switch Front Passenger Seat Belt Switch Driver Side Second Row Seat Belt Switch Center Second Row Seat Belt Switch Passenger Side Second Row Seat Belt Switch Passenger Seat Occupant Detection Sensor Rear seat occupied sensor on driver side Rear seat occupied sensor on passenger side Driver Thorax Airbag Crash Sensor Front Passenger Thorax Airbag Crash Sensor Driver Side Rear Thorax Airbag Crash Sensor Passenger Side Rear Thorax Airbag Crash Sensor Driver Front Airbag Crash Sensor Passenger Side Front Airbag Crash Sensor Driver Belt Force Limiter Front Passenger Belt Force Limiter Driver Seat Position Sensor Front Passenger Seat Position Sensor K19 K75 K145 N95 N131 N132 N153 N154 N196 N197 N199 N200 N201 N202 N251 N252 N253 N295 N296 N297 N298 N490 N491 N563 N751 T16 Seat Belt Indicator Lamp Airbag Indicator Lamp Front Passenger Airbag -Disabled- Indicator Lamp Driver Airbag Igniter Front Passenger Airbag Igniter 1 Front Passenger Airbag Igniter 2 Driver Seat Belt Tensioner Igniter 1 Front Passenger Seat Belt Tensioner Igniter 1 Driver Side Rear Seat Belt Tensioner Igniter Passenger Side Rear Seat Belt Tensioner Igniter Driver Thorax Airbag Igniter Front Passenger Thorax Airbag Igniter Driver Side Rear Thorax Airbag Igniter Passenger Side Rear Thorax Airbag Igniter Driver Head Curtain Airbag Igniter Front Passenger Head Curtain Airbag Igniter Battery Interrupt Igniter Driver Knee Airbag Igniter Front Passenger Knee Airbag Igniter Driver Seat Belt Tensioner Igniter 2 Front Passenger Seat Belt Tensioner Igniter 2 Driver Airbag Release Valve Igniter Front Passenger Airbag Release Valve Igniter High-Voltage Battery Interrupt Igniter Battery Interrupt Igniter, 48 Volt Data Link ConnectorJ234 J285 J519 J528 J533 J706 J854 J855 J1097 J1098 Airbag Control Module Instrument Cluster Control Module Vehicle Electrical System Control Module Roof Electronics Control Module Data Bus on Board Diagnostic Interface Passenger Occupant Detection System Control Module Left Front Seat Belt Tensioner Control Module Right Front Seat Belt Tensioner Control Module Left Rear Seat Belt Tensioner Control Module Right Rear Seat Belt Tensioner Control ModuleWiring colors: Diagnostics CAN Instrument panel insert CAN Sub-bus system FlexRay LIN bus Convenience CAN 2 Input signal Output signal59 Driver assist systemsIntroductionThis topic begins with short descriptions of the five most important innovations in the 2019 A6. All of these innovations made their début in the 2019 Audi A8. The innovations concern new hardware which continues to pave the way for autonomous driving, a new and innovative operating concept, and new driver a