TECHNICAL DOCUMENTATION
SSP 290 Audi A3 2004

This PDF is currently unavailable.
Read document text
Service.ProCarManuals.comAUDI A3 ´04Self Study Programme 290For internal use onlyThis SSP is intended to give a general outline of the design and operation of the Audi A3 ‘04. Further relevant information can be found in the various Self Study Programmes and other media such as the CAN data bus CDs.ProCarManuals.com Vorsprung durch TechnikMedia containing further material on the Audi A3 ‘04 include the CAN data bus CDs Parts 1 and 2. This Self Study Programme deals exclusively with the special features of the Audi A3 ‘04.2ContentsPage Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04Brief outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06BodyBody shell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front bumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear bumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Passenger protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08 10 13 14Engine1.6 l 2V engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 l 4V FSI engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil filter module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accelerator pedal module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 l V6 engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Camshaft timing control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-return fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9 l 4-cylinder TDI engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 l 4V TDI unit injector system engine. . . . . . . . . . . . . . . . . . . . . . . . . . . Diesel rapid start system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 17 24 27 32 36 38 40 42 46 48 51ProCarManuals.comGearboxDirect-shift gearbox 02E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Automatic gearbox 09G (6-speed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Running GearFront axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear axle for quattro® drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 58 59 60Electrical SystemBus topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Convenience electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Heating/Air ConditionerDesign and operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Mode of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70ServiceSpecial tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72The Self Study Programme contains information on design features and functions. The Self Study Programme is not intended as a Workshop Manual. Values given are only intended to help explain the subject matter and relate to the software version applicable at the time of SSP compilation. Use should always be made of the latest technical publications when performing maintenance and repair work.AttentionNew3IntroductionThe new Audi A3 ‘04 The new top sports model in the compact class is raring to go and is to take the place of its predecessor of the same name. In combination with the highly dynamic running gear, powerful petrol and diesel engines up to 177 kW, quattro drive and the new automatic-shift sporty gearbox DSG make sure the image of driving fun created by the sporty body design does not remain an empty promise. The use of exclusive equipment and materials again guarantees that the high standards typical of the large Audi models come into play in the compact class as well.ProCarManuals.comGateway as separate control unitV6 engineDirect-shift gearbox 4Body shell modificationsProCarManuals.comIndividual climate controlSSP290_018Electromechanical steering 5IntroductionBrief outlinePrincipal Audi A3 ‘04 dimensions. The diagrams below illustrate the changes in relation to the predecessor model.Passenger compartment length + 57 mm Shoulder width Front Rear + 42 mm + 23 mm Height/unladen -10 mm Front head room + 2 mm Knee room + 20 mmProCarManuals.comVolume: ± 0 mm+ 56 mmShoulder width Front Rear + 16 mm + 14 mm Vehicle width + 30 mmWheelbase + 65 mm Vehicle length + 48 mmRear ref. point to centre of rear axle + 8 mmSSP290_005Length Width Height Wheelbase Turning circle Tank capacity4203 mm 1765 mm 1421 mm 2578 mm 10,70 m 55 litresFront track Rear track Gross weight Kerb weight Luggage compartment volume Drag coefficient1536 mm 1517 mm 1835 kg 1275 kg 350 litres 0.31 cd6The vehicle dimensions indicated are measured in mm at kerb weight.884 624 1536 1765 121 1421 871 1517 1957ProCarManuals.com9749358652578 42037601511 1343 1392796 1000SSP290_006 7655BodyBody shellLightweight body Bearing in mind the requirements in terms of – Passive safety – Torsional rigidity – Vibration damping – Acoustics vehicle development work focused on lightweight construction methods. Upper body The strength of the upper body is achieved by employing modern fastening methods. A great deal more use has been made of laser and bonded seams than in the predecessor model. The weight component of high and ultra-high strength panels in the upper body has been increased to almost 50 %.ProCarManuals.comSSP290_072Lower bodyProportion of high and ultra-high strength panels in upper body Proportion of high and ultra-high strength panels in lower bodyWhilst maintaining the same strength, material weight reductions of around 25 % were obtained for certain components through the use of tailored blanks and high/ ultra-high strength panels. The weight component of high-strength steel panels in the underbody is 56 % and that of ultra-high strength panels 15 %.62 %"Tailored blanks" are panels manufactured to size with different material thicknesses.Steel panels 8SSP290_071Roof zero-gap joint The roof and side wall frames are seamlessly joined by way of laser soldering. The overall length of the laser soldered joint is 3 metres.A-A sectionRoof Laser-soldered zero-gap joint Outer side panelProCarManuals.comA-A sectionSSP290_069Body components This robust upper body structure helps to increase the overall bending strength and torsional rigidity in the trimmed body by 20 %. Major factors in this were optimised joints and a modified joining sequence.Right side wall sectionFloor panel Left side wall section two-part view SSP290_011 9BodyFront bumperThe bumper of the Audi A3 ‘04 is painted entirely in the same colour as the vehicle. It comprises the following components: – Bumper cover – Cover for towing eye – Side end plate – Radiator grille – Centre grille – Side air inlet grilles and – Bumper bracketProCarManuals.comSSP290_01210The bumper bracket takes the form of an aluminium cross member.Connection to the longitudinal members is provided by the so-called steel crash boxes.Radiator Air conditioner condenserFront endFront longitudinal memberProCarManuals.comAir deflector unitCrash boxSSP290_014 Bumper cross memberThe zero-gap joint between bumper and wing is guaranteed by a zero-gap joint bolt.This connects the wing to the bumper cover.Securing stripFitted bolt WingBumper coverSSP290_06111BodyWith a view to achieving optimum crash safety, the development work for the entire bumper system was coordinated from the outset with that for the front end and its addon components (air-conditioner condenser and radiator. Success was thus achieved in considerably reducing damage to these components, particularly in the 15 km/h model damage and 64 km/h Euro NCAP* tests. In the model damage test, the bumper bracket strikes the front end carrier and breaks it out of its bolted connections to the body. This produces a larger crumple zone for the bumper bracket and avoids damage to the air conditioner condenser and radiator. The transverse forces acting on the longitudinal member in the model damage and Euro NCAP* tests are reduced and robust deformation properties result.RadiatorProCarManuals.comAir conditioner condenser Air deflector unitFront longitudinal member Crash box Bumper cross memberSecuring strip Fitted bolt WingOffset deformation barrier 40 % vehicle cover SSP290_015To avoid wing damage in the model damage test, the bumper cover detaches itself from the wing and breaks away to the side.Bumper coverSSP290_062* New Car Assessment Programme Association of government agencies, institutes and organisations at a European level, e.g. TÜV, ADAC, insurers, aimed at providing consumers with transparent vehicle safety standards.12Rear bumperThe bumper bracket and support bracket are produced as aluminium extruded sections.ProCarManuals.comThe bumper comprises the following components – Bumper cover – Spoiler – Cover for towing eye and – End plateSSP290_068The zero-gap joint between bumper and side panel takes the form of a clipped rather than a bolted joint. The clipped joint is fastened by a bolt which is accessible after removing the rear light.SSP290_07413BodyPassenger protectionSafety systems The safety system in the new Audi A3 ‘04 has been revised and adapted accordingly to meet with current and future demands in terms of occupant safety. The system essentially consists of familiar components such as: airbag control unit, driver's and front passenger's airbag, front side airbags, front belt tensioners, sideguards (head airbags) and side impact recognition sensors. New features are the external front airbag crash sensors (so-called upfront sensors for detection of head-on collisions) and battery deactivation in the event of a crash on vehicle models with the battery fitted in the luggage compartment. Vehicles can optionally be equipped with a key switch for front passenger's airbag deactivation and the corresponding warning lamp. The Audi A3 ’04 safety system is rounded off by the active head restraints in the front seats. Key: E224 Airbag disabling key switch, front passenger side Side airbag crash sensor, driver side (B-pillar) Side airbag crash sensor, front passenger side (B-pillar) Rear side airbag crash sensor, driver side Rear side airbag crash sensor, front passenger side Front airbag crash sensor, driver side Front airbag crash sensor, front passenger side Engine control unit Airbag control unit Control unit with display in dash panel insert Convenience system central control unit Data bus diagnostic interface (gateway) Battery cut-off relay Airbag warning lamp Airbag disabled warning lamp, front passenger side Airbag igniter, driver side Airbag igniter 1, front passenger side Belt tensioner igniter 1, driver side Belt tensioner igniter 2, front passenger side Side airbag igniter, driver side Side airbag igniter, front passengerside Curtain airbag igniter, driver side Curtain airbag igniter, front passenger side Connector, 16-pin diagnostic connectionG179 G180 G256 G257 G283 G284ProCarManuals.comJ220 J234 J285 J393 J533 J655 K75 K145For the first time use is made in the Audi A3 ‘04 of airbag modules which are not subject to any replacement intervals.N95 N131 N153 N154 N199 N200 N251 N252T16 Always heed the corresponding safety regulations outlined in the Workshop Manuals before working on the airbag system.14G 283G 284K145 J220 J285/K75AIRBAGAIRBAGOFFE224AUS EINT16 J533N95/G85 N131ProCarManuals.comJ234N199N200G179N153N154G180N201N202N251 G 256N252 G 257J393J655SSP290_103 15EngineEngines – Audi A3 ‘04Technical data of 1.6 l 2V engine Code letters: Capacity: Stroke: Bore: Compression ratio: Valves: BGU 1595 cm3 77.4 mmPower [kW]120 110 100 90 80 70 60 50 40 30 300 275 250 225 200 175 150 125 100 75 50 25 1000 3000 5000 0 700081.0 mm 10.3 : 1 two per cylinder 75 kW/102 hp at 5600 rpm 148 Nm at 3800 rpm 1-3-4-220 10ProCarManuals.comPower:0Engine speed [rpm]Torque:SSP290_020Firing order: Capacity Engine oil incl. filter: Engine management: Consumption:4.6 lMPI Urban 9.6 - 9.8 l/100 km Non-urban 5.5 - 5.7 l/100 km Average 7.0 - 7.2 l/100 kmAcceleration:0 - 100 km/h in 11.9 sEmission standard: EU 4 Fuel: Premium Unleaded 95 RONSSP290_00916Torque [Nm]Technical data of 2.0 l FSI engine120 300 275 250 225Torque [Nm] 17Code letters: Capacity: Stroke: Bore: Compression ratio: Valves:AXW1101984 cm3 92.8 mmPower [kW]100 90 80 70 60 50200 175 150 125 100 75 50 25 1000 3000 5000 0 700082.5 mm 11.5 : 1 four per cylinder 110 kW/150 hp at 6000 rpm 200 Nm at 3500 rpm40 30 20 10 0ProCarManuals.comPower:Torque: Camshaft adjustment range:42° crank angleEngine speed [rpm] SSP290_004Firing order: Capacity Engine oil incl. filter: Engine management: Consumption:1-3-4-24.6 lMED 9.5.10 Urban 9.6 - 10.1 l/100 km Non-urban 5.3 - 5.8 l/100 km Average 6.9 - 7.4 l/100 km 0 - 100 km/h in 9.1 sAcceleration:Emission standard: EU 4 Fuel: Premium Plus Unleaded 98 RONSSP290_029Design and operation are described in Self Study Programme 279.EngineFSI engine Use is made of the longitudinally mounted 2.0 l 4V FSI engine familiar from the A4. The modifications are described in the following. For transverse installation, a new intake manifold was developed with changeover barrel as switching element. For space reasons the torque pipes had to be installed in crossover arrangement to maintain the optimum intake manifold length. Enlarging the diameter of the changeover barrel to 60 mm (A4 50 mm) permitted an increase in the air throughput of the short power pipes.For further details refer to Self Study Programme 279.ProCarManuals.comTop sectionCrankcase breather connectionThrottle valve unit Centre sectionSolenoid switching valve Changeover barrel Inner section Switching module drive unitPressure and temperature sensor Bottom sectionSSP290_03818Engine management without air-mass meter The management system for the 2.0 l FSI engine has been switched from MED7.1.1 to MED9.5.10. The use of a 32-bit processor and a new PCB layout provides scope for the future introduction of functions currently still under development. The control unit design has become more compact thanks to new output stages (less heat generation). The injector actuation voltage has been reduced from 90 V to 65 V. This was made possible by so-called armature free travel. Armature free travel was achieved by decoupling the injector needle from the armature. Energisation of the solenoid first causes the armature to be energised (breakaway torque) and the injector needle is raised after a delay by way of a driver.ProCarManuals.comFine strainerArmature free travel 4/100 mmInjector needle Solenoid ArmatureInjector needleTeflon sealSSP290_023The Teflon seal always has to be replaced after removing the injector.19EngineFSI block diagramActivated charcoal filterFuel tank breather valveTemperature sensorIntake-manifold pressure sender and temperature probeProCarManuals.comThrottle valve actuator (electronic throttle) Engine control unit Exhaustgas recirculation valveCANDiagnosis lamp Accelerator pedal module Diagnosis interface ImmobilizerLoad detection is based on the following sensor signals: – Atmospheric pressure supplied by altitude sender in engine control unit – Intake-air temperature supplied by sensor fitted upstream of throttle valve – Throttle valve position20High-pressure pumpCamshaft adjusterIgnition coil/spark plugLowpressure sensorInjector pressure sensorPhase sensorLambda probe (LSU) 2xProCarManuals.comTemp. sensor Knock sensor 2x Enginespeed senderPrimary catalytic converter 2xLambda probe (LSF) 2x Exhaust-gas temperature sensorTank with demand-regulated fuel pumpNOx catalytic converterNOx sensorSSP290_043– – – –Pressure and temperature in intake manifold via twin sensor at intake manifold Position of EGR valve flap Position of in-cylinder flow flaps Position of inlet camshaft21EngineModes of operation An air-controlled combustion process permits homogeneous and stratified charge operation. The engine electronics always set the optimum operating status to suit the load condition and accelerator pedal position. There are 4 main modes of operation: – Stratified lean with exhaust-gas recirculation – Homogeneous lean with no EGR – Homogeneous with Lambda = 1 and EGR – Homogeneous with Lambda = 1 without EGR14 12 10Homogeneous with EGR HomogeneousProCarManuals.comMean pressure [bar]8 6Homogeneous lean4 2 0 0 1000 2000 3000 4000 5000 6000 7000Stratified leanEngine speed [rpm]SSP290_104Exhaust-gas recirculationExhaust-gas recirculation valveThe exhaust-gas recirculation valve takes the form of a butterfly valve as in the A4. On account of its special installation position, the EGR valve fitted is water-cooled.SSP290_09122Exhaust system To increase the torque in the lower engine speed range, the front section of the exhaust system is of the dual-flow type. This necessitates the use of two primary catalytic converters in the exhaust manifold. These are permanently connected to the exhaust manifold. Two wide-band probes monitor the mixture composition. Two stepchange probes monitor catalytic converter action. In lean mode, the storage catalytic converter provides buffer storage for the nitrogen oxides (NOx), with the NOx sensor monitoring the degree of saturation and triggering regeneration of the storage catalytic converter.ProCarManuals.comContinuous-action probePrimary catalytic converterNOx sensor Temperature sensor NOx storage catalytic converterStep-change probeSSP290_00723EngineOil filter module The new oil filter module in the Audi A3 ‘04 was developed as a highly integrated plastic assembly containing the following units for example: – – – – Oil pressure relief valve Replaceable paper element as oil filter Integrated water-cooled oil cooler Settlement chamber for crankcase breather coarse oil separationCrankcase breather settlement chamber Oil outletProCarManuals.comWater inlet Oil coolerWater outletOil inletOil pressure relief valvePaper filter elementSSP290_037 Oil drain valve24Filter replacement Before replacing the paper filter element, the oil filter is to be drained using the oil drain adapter T 40057. This requires the following operations: 1. Unscrew plastic cover at oil filter.ProCarManuals.comSSP290_089 Plastic cover at oil filterOil drain adapter T 400572. Screw home oil drain adapter T 40057 with drain hose in bottom part of oil filter housing and drain off oil (approx. 0.5 l). Screwing in the adapter opens a drain valve in the oil filter housing.Threaded ring with piston guide O-ringDrain pipeNote: Pay attention to Maintenance booklet.SSP290_08325EngineFuel supply control As with all petrol engines, as soon as the driver's door of the Audi A3 ‘04 is opened the fuel pump is actuated by the onboard power supply control unit and builds up the fuel pressure in the system. In contrast to the A4, use is made of a demand-regulated fuel system. The electric fuel pump only supplies the high-pressure fuel pump with the amount of fuel it requires at a given load and engine speed. The lower power input reduces fuel consumption. The fuel pump control unit J538 is fitted in the cover for the fuel gauge sender. It regulates the low-pressure delivery between 0.6 l/h and 55 l/h at a constant 4 bar. On warm starting, the pressure is increased from 4 bar to 5 bar to prevent the formation of vapour bubbles and to permit injection of the quantity required for cold starting.SSP290_119ProCarManuals.com200180160140Delivery Q in l/h120100806040200 6 7 8 9 10 11 12 13 14 15Operating voltage in VSSP290_105Q typ 4 bar26Accelerator pedal module The accelerator pedal module in the Audi A3 ‘04 is arranged vertically. Accelerator pedal, kinematic mechanism, pedal position sender, kickdown element and now also as a new feature the pedal stop, have been combined into one unit. In addition to improved ergonomics, the new accelerator pedal module has the advantage that no basic setting is required for kickdown. As the pedal stop is an integral part of the module, there are no tolerances between pedal and body-end stop. The module always supplies the same sender values in whatever vehicle it is fitted. A new feature is the pedal position sender in the form of a linear travel sender. The two accelerator pedal position senders G79 and G185 are of the non-contacting type and employ the induction principle. The kinematic mechanism of the accelerator pedal module converts the angular movement of the accelerator pedal into linear motion. Together with the friction element, the spring assembly provides a normal pedal feel.ProCarManuals.comPedal Pedal stopSpring assembly SSP290_131Metal plateFriction elementHalf housing with cover containing the two sensors G97 and G185 SSP290_13327EngineDesign and operation As previously, the pedal position sender has two independent sensors (G79/G189). One excitation coil and three receiver coils as well as control and evaluation electronics are provided for each sender on a multi-layer PCB. The geometry of the receiver coils takes the form of a diamond shape and the coils are arranged so as to have a mutual phase offset. The excitation coils are located above the receiver coils. A metal plate is attached to the kinematic mechanism of the accelerator pedal module such that it moves along in a straight line close to the PCB on pressing the accelerator pedal.For greater clarity, design and operation are explained on the basis of one sender only.ProCarManuals.comPins 1 to 6 PCB housingProcessorsReceiver coil areaContacts for pin connectionSSP290_13228Function An alternating current flows through the excitation coil. This generates an electromagnetic alternating field, the induction of which permeates the metal plate. In turn, the current induced in the metal plate produces a second electromagnetic alternating field around the metal plate. The alternating fields of both the excitation coil and the metal plate act on the receiver coils and induce a corresponding AC voltage in them. Whereas the induction of the metal plate is not position-specific, the induction of the receiver coils is governed by their position in relation to the metal plate and thus also by the position of the plate itself. As the extent to which the metal plate covers the respective receiver coils is a function of position, their induced voltage amplitudes differ according to position. The evaluation electronics rectify the AC voltages of the receiver coils, amplify the voltages and form the ratio between the output voltages of the three receiver coils (ratio measurement). Following voltage evaluation, the result is converted into a corresponding linear voltage signal and made available at the sender output.ProCarManuals.comExample of defined position.Accelerator pedal valueU2 U1 U30%U1 0Accelerator pedal valueU2 U1 U350 %U2 0Accelerator pedal valueU2 U1 U3100 %U3 0SSP290_120SSP290_12829EngineIn addition to non-contacting and thus wearfree operation, the advantage of this sender is its ratio measurement method. Ratio formation makes the travel-proportional output signal largely insensitive to component tolerances and electromagnetic interference. As no magnetic materials are required, there are hardly any deviations caused by decreasing magnetism. The output signals of the two senders are generated such that they are identical to the previous sliding contact senders (refer to graph). Modifications to the engine control units are therefore not necessary.Pin assignment at pedal position sender: Pin 1 Pin 2 Pin 3 Pin 4 Power supply 5 V for G185 Power supply 5 V for G79 Earth for G79 Voltage signal from G79 (refer to graph) Earth for G185 Voltage signal from G185 (refer to graph)ProCarManuals.comPin 5 Pin 6The accelerator pedal module is the same for both diesel and petrol engines. There are however differences for manual and automatic gearboxes.Kickdown range Accelerator pedal5,0 G79Signal voltage in VG1850 20 % 40 % 60 % 80 % 100 %SSP290_135Driver input torque Mechanical fullthrottle stopAccelerator pedal end stop30ProCarManuals.comNotes31Engine3.2 l V6 engine The idea of using a VR engine (common term until 1987) was conceived in mid-1977. This concept then led to the design of a 2.0 l, 2-valve engine and finally to the development in 1988 of the 2.8 l, 2-valve engine, which entered series production with the code letters AAA. Further information on VR engines can be found in the following SSPs: 174: Modifications to VR6 engine 195: The 2.3 l V5 engine 212: Variable intake manifolds for VR engines 246: Camshaft timing control The design and operation of this engine are outlined in Self Study Programme 127. The engine is fitted in the new Audi A3 ‘04 and the Audi TT, as this is the only design with which it is possible to achieve a capacity of 3.2 l with front transverse installation in this vehicle class. The engine technology has of course been constantly modernised. Comfort, power and the stringent emission standards were accordingly adapted to the requirements of the new Audi A3 ‘04. The technical modifications applying to this engine are described on the following pages.ProCarManuals.comSSP290_108Design of basic engine – V-shaped grey cast iron cylinder block and crankcase with a cylinder angle of 15° – Four-valve cylinder head with roller-type rocker fingers - driven via a simple roller chain32– Variable inlet and exhaust camshaft timing – Plastic variable intake manifold – Pencil-type ignition coil for each cylinderTechnical data of VR6 3.2 l 4V engine Code letters: BDBCapacity:3189 cm3240 220480 440 400 360 320 280 240 200 160 120 80 40 1000 3000 5000 0 7000Stroke:95.9 mm200 180 160Power [kW]140 120 100 80 60 40 20Compression ratio: Valves:11.3 : 1 four per cylinderProCarManuals.comEngine management: Power:ME7.1.1 177 kW/241 hp at 6250 rpm0Engine speed [rpm] SSP290_109Torque:320 Nm at 2500 - 3000 rpmFiring order:1-5-3-6-2-4Camshaft adjustment range:Inlet 52° crank angle Exhaust 42° crank angleEmission standard: EU 4Fuel:Premium Plus Unleaded 98/95 RONTorque [Nm] 33Bore:84.0 mmEngineVariable intake manifold The design principle of the overhead variable intake manifold arrangement with separate main and power manifold was adopted from the 2.8 l engine and adapted to the new situation. Good cross-sectional utilisation of the individual intake manifolds was achieved by further reducing flow and pressure losses. This resulted in higher characteristic specific power values.Crankcase breather Main manifold Resonance tubes Throttle valve assemblyPower manifoldProCarManuals.com290_084 Bottom part of intake manifold Vacuum unit for changeover barrel actuationOperation The changeover barrel is turned through 90° by a vacuum unit. The variable intake manifold changeover valve N156 provides actuation. With the engine stopped and at idle, the changeover barrel is set to power position (short intake path). It is held in this position by spring force. The variable intake manifold changeover valve N156 is then not energised by the engine control unit J220.34Torque positionPower manifold Changeover barrel closedAs of an engine speed of 1100 rpm, the changeover barrel is turned through 90°, thus sealing off the power pipes. The cylinder currently in the induction phase draws in air through the long torque pipes directly from the main manifold.Torque pipeProCarManuals.comSSP290_085Power positionChangeover barrel openAs of an engine speed of 4100 rpm, the variable intake manifold changeover valve is no longer energised and atmospheric pressure is applied to the vacuum unit. The changeover barrel is then turned back through 90° to its initial position by means of spring force. The cylinder draws in air via its short intake manifold. This cylinder obtains its air from the power manifold. The power manifold is supplied with air by way of the torque pipes of the other cylinders which are not currently in the induction phase.Power pipe SSP290_08635EngineCamshaft timing control The principle of twin camshaft timing control has been extended on the 3.2 l engine to include scope for continuous exhaust camshaft adjustment. The inlet and exhaust camshaft adjustment angles are 52° and 42° crank angle respectively. The extended exhaust camshaft adjustment range produces a greater overlap angle than with previous applications. This has the following advantages in terms of internal exhaust gas recirculation: – More economical consumption thanks to a reduction in charge cycle work – Extended part throttle range with internal exhaust gas recirculation – Smoother operation – Less sensitivity to mixture fluctuations – Implementation of exhaust gas recirculation even with cold engineProCarManuals.comRotorStator Rotary motors Oil pressure chamberSolenoid valvesSSP290_08736Inlet camshaft The inlet camshaft adjustment angle is a continuous 52° crank angle. The design basic position of the inlet camshaft is set to opening retard. The rotor is set to "retard" stop. Advance and retard are implemented as a function of the maps stored in the control unit. The position of the camshaft is sensed by the Hall sender G40. The following measured quantities are also required by the engine control unit for camshaft timing control:ProCarManuals.comOil chamberSSP290_081 Pressurised oil ducts– Air mass signal from air-mass meter G70 – Engine speed from engine speed sender G28 – Coolant temperature from coolant temperature sender G62Exhaust camshaftStatorThe exhaust camshaft adjustment angle is a continuous 42° crank angle. With the exhaust camshaft, it was not possible on account of the broad adjustment range to ensure reliable starting in the retard position under all operating conditions, particularly at low temperatures. For this reason, the exhaust camshaft adjuster is mechanically locked in the "advance" position by means of a locking pin. The camshaft also remains in this basic position at idle. There is thus little valve overlap, resulting in both reliable starting and smooth idling.Rotor Locking pinSSP290_082 Depressurised oil chamber37EngineNon-return fuel system With this fuel system there is no return pipe from the rail to the tank and thus also no pressure regulator at the rail. The pressure regulator is inserted in the fuel filter, which is attached in readily accessible position to the right side of the fuel tank. The fuel in the tank does not become as hot with this system, as there is no return flow of hot fuel from the engine. Evaporation emissions are reduced.The system is always to be bled at the rail on completion of work on fuel system.Fuel return to fuel tankElectric fuel pumpProCarManuals.comFuel filter with pressure regulatorMTankBreather valveRailInjectors SSP290_100Fuel pressure regulator The fuel is conveyed by the electric fuel pump to the fuel filter, from where it flows to the rail. The fuel pressure regulator and fuel filter form one unit. The regulator maintains the fuel pressure at a constant 4 bar. This is achieved by a spring-loaded diaphragm valve. The cut-off fuel is returned directly to the fuel tank.Fuel supply to fuel tank Fuel supply to fuel railFuel pressure regulator Fuel return to fuel tank 38Fuel filterSSP290_101Engine management Due to the introduction of variable exhaust valve control and the associated internal exhaust gas recirculation, the residual exhaust gas content of the cylinder has to be calculated, leading to an increase in computation work in the processor. Use is made for engine management of the Bosch Motronic ME7.1.1. The processor speed was increased from 32 to 40 MHz. The increased computer capacity also helps to improve calculation of the intake manifold pressure and enhance mixture formation. The radiator fans are controlled by way of a discrete wire from the engine control unit, which contains the information required to set the desired coolant temperature.Engine management, gearbox control, ABS, ESP, air conditioner, immobilizer and dash panel insert are interlinked via the drive system CAN bus.ProCarManuals.comSSP290_11639EngineExhaust system The exhaust system is of dual-flow design as far as downstream of the front silencers. This ensures a very high torque level in the low engine speed range. The exhaust system is equipped with one catalytic converter and two Lambda probes per exhaust pipe. The probe upstream of the catalytic converter is a Bosch LSU 4.9 wide-band Lambda probe with regulated heating (G39, G130). There is thus a very early Lambda control response. The probe downstream of the catalytic converter takes the form of the conventional Lambda step-change probe (G108, G131), which is only used to monitor the catalytic converter. Secondary air injection helps to ensure the early response of the two catalytic converters.Lambda probes upstream of catalytic converterProCarManuals.comDecoupling elementCatalytic converters Front silencerMounting Centre silencerLambda probes downstream of catalytic converter MountingRear silencerSSP290_09840Switchable exhaust flap The exhaust flap is switched by the engine control unit J220 by means of a vacuum unit. Intake manifold pressure is applied to this by the solenoid valve N321, causing it to close. If the flap is to be opened, the solenoid valve N321 switches and atmospheric pressure is applied to the vacuum unit. The force of the spring in the vacuum unit opens the flap.Flap positions Open: (deenergised) In all gears and at idle Engine speed n 2000 rpm Engine load 40 % - 100 % Closed: (energised) In all gears Engine speed n 2000 rpm Engine load 40 % Hysteresis: Flap opens on exceeding engine speed of 2000 rpm or 40 % engine load. Flap closes on dropping below engine speed of 1800 rpm or 30 % engine load.ProCarManuals.comFlap open Non-return valve Intake manifold Vacuum unit with exhaust flapVacuum reservoirFlap openJ220 SSP290_079DeenergisedEnergisedFlap closed Non-return valve Intake manifoldVacuum reservoir J220Flap closedSSP290_080Atmospheric pressureVacuum 41EngineFuel tank Use is made in the new Audi A3 ‘04 of a blowmoulded fuel tank with a capacity of 55 litres for the FWD version and 60 litres for the "quattro" version. The fuel tank is located in crash-safe position between the rear wheels outside the passenger compartment and the rear-end impact zone. Thanks to this design the vehicle will be able to comply with future US rear-end crash legislation. A heat shield provides thermal insulation with respect to the exhaust system.ProCarManuals.comBreather pipeDelivery unitTo ACF valveSSP290_12142A two-chamber tank is required for the quattro®drive. A suction jet pump and an additional level sender are integrated into the second tank chamber.ProCarManuals.comBreather pipeDelivery unitHeat shieldTo ACF valve Fuel filter SSP290_12243EngineSystem layoutActuators/sensorsHot-film air-mass meter G70 Engine control unit J220Engine speed sender G28Hall sender G40 and Hall sender 2 G163Pedal position sender/accelerator pedal module with accelerator pedal position sender G79 and accelerator pedal position sender 2 G185ProCarManuals.comESP control unit J104 Lambda probe upstream of catalytic converter G39 Lambda probe II upstream of catalytic converter G108 Brake light switch F and brake pedal switch F47Automatic gearbox control unit J217 Lambda probe after catalytic converter G130 Lambda probe II after catalytic converter G131 Throttle valve control unit J338 with throttle valve drive G186 (electric power control) Throttle valve drive angle sender 1 G187 Throttle valve drive angle sender 2 G188 Clutch travel sender G162 Climatronic control unit J255 Convenience CAN Data bus diagnostic interface J533 Airbag control unit J234Coolant temperature sender G2 Coolant temperature sender - radiator outlet G83Dash panel insert CANKnock sensor 1 G61 and knock sensor 2 G66Control unit with display in dash panel insert J285Drive system CAN Diagnosis CANAdditional signals: Cruise control system switch ON/OFF 44Fuel pump relay J17 Fuel pump G6Lambda probe heater Z19Injectors N30, N31, N32Lambda probe 2 heater Z28 Injectors N33, N83, N84ProCarManuals.comLambda probe heater Z19 Ignition coils N70 (no. 1 cyl.), N127 (no. 2 cyl.), N291 (no. 3 cyl.)Lambda probe 2 heater Z28Variable intake manifold changeover valve N156Ignition coils N292 (no. 4 cyl.), N323 (no. 5 cyl.), N324 (no. 6 cyl.)Continued coolant circulation relay J151 and continued coolant circulation pump V51Activated charcoal filter system solenoid valve 1 N80Secondary air pump relay J299 and secondary air pump motor V101Exhaust flap valve N220Secondary air inlet valve N112PWM-controlled radiator fanThrottle valve control unit J338 with throttle valve drive G186Inlet/exhaust camshaft timing adjustment valve 1 N205 and N318 SSP290_088Engine1.9 l 4-cylinder TDI unit injector system engine The engine is a modified version of the original 1.9 l/77 kW engine with new features for the following areas: – Unit injector system - optimised in part throttle range with higher injection pressure – Exhaust gas recirculation electrically actuated and with separate cooler – Modified combustion chamber – Use of thin-walled oxidation catalytic converterProCarManuals.comSSP290_00846Technical data Code letters: Capacity: Stroke: Bore: Compression ratio: Design: BKC 1896 cm3 95.5 mm 79.5 mm 19.0 : 1 In-line four-cylinder diesel engine with VTG turbocharger 77 kW/105 hp at 4000 rpmPower [kW]120 110 100 90 80 70 60 50 40 30 20360 330 300 270 240180 150 120 90 60 30 1000 3000 5000 0 7000ProCarManuals.comPower:10 0Engine speed [rpm]Torque:250 Nm at 1900 rpmSSP290_019Firing order:1-3-4-2Capacity Engine oil incl. filter: Engine management:4.5 lBosch EDC 16Emission standard: EU 4Fuel:Diesel, min. 51 CNTorque [Nm] 47210Engine2.0 l 4V TDI unit injector system engine Technical data Code letters: Capacity: Stroke: Bore: BKD 1968 cm3 95.5 mm 81.0 mmPower [kW]120 110 100 90 80 70 60 50 40 30 20 10 390 360 330 300 270 240 210 180 150 120 90 60 0 1000 3000 5000 7000Compression ratio: 18.0 : 1 Design: 4-cylinder 4-valve 4-stroke turbodiesel in-line engine 103 kW/140 hp at 4000 rpm 320 Nm at 1750 - 2500 rpm 1-3-4-2ProCarManuals.comPower:0Engine speed [rpm] SSP290_003Torque:Firing order: Turbocharger system:Garret GT 1749V with variable turbine geometry Bosch EDC 16Injection system: Capacity Engine oil incl. filter: Consumption:3.8 l Urban 7.2 - 7.3 l/100 km Non-urban 4.5 - 4.6 l/100 km Average 5.5 - 5.6 l/100 km 0 - 100 km/h in 9.5 sAcceleration: Emission standard: Fuel:EU 4 Diesel, min. 51 CNSSP290_00148Torque [Nm]Modifications to unit injector system engine Piston Enlarging the cylinder bore made it possible to increase the capacity from 1.9 l to 2.0 l. The piston with central combustion chamber cavity and emission-optimised geometry was designed with reduced valve cut-out depth to lessen the pollutant volume in the combustion chamber. An oil ring duct in the piston provides cooling of the piston crown.Central combustion chamber cavityProCarManuals.comSSP290_042 All-round oil ring duct Duct for oil spray jetCylinder head The cylinder head design has been changed from a two to a four-valve system with two overhead camshafts. The glow plugs are located in the area through which oil passes. The valves are actuated via roller-type rocker fingers with hydraulic valve lifters. The unit injector system is driven by the exhaust camshaft via roller-type rockers.Roller-type rockerVariable intake manifoldExhaust camshaft Glow plug Roller-type rocker finger Inlet camshaft Inlet portExhaust portSSP290_002 49EngineSupport frame To provide the necessary cylinder head rigidity, the conventional camshaft cover was replaced with a support frame (ladder frame). This is bolted by means of the two inner rows of bolts directly into the heads of the cylinder head bolts. The frame accommodates the rocker shaft for the pump elements, the wiring connections for the glow plugs and the solenoid valves of the unit injector system.SSP290_092Cross-flow cylinder headProCarManuals.comThe valves are arranged around the central unit injector system in angled star configuration with two tangential inlet ports and one exhaust port in the form of a forked pipe. This creates optimum conditions for giving the intake air the appropriate swirl and ensuring the best possible cylinder charge.Exhaust portInlet port SSP290_021Unit injector system The injector is of prime importance in complying with the stringent EU 4 limit values. The centrally located 6-hole injector with tapered, flow-optimised orifices was improved to achieve a 10 % increase in part throttle injection pressure. To obtain the central installation position, use was made of a 114° conical seat instead of a flat cylinder head rest with packing plate.SSP290_096 50Diesel rapid start system Use is made of a combined system of steel glow plugs and control unit to improve diesel engine starting (key start = starting without preheating). This newly developed glow plug requires a warm-up time of max. 2 seconds, as opposed to the usual 5 second period. Power semi-conductors which replace the conventional electromagnetic relay are used in the control unit to actuate the glow plugs. Separate actuation, monitoring and diagnosis are thus possible for each glow plug. To achieve the very short warm-up time (to 1000 °C in 2 seconds), the filament was designed as a sensor and heater filament and shortened to concentrate the glow effect in the front area of the plug.Glow plug designSelf-regulating glow plug SR5ProCarManuals.comElectronically controlled glow plug "New"Glow plug tip"Old"SSP290_106Approx. 11 V are briefly applied on a pulsewidth modulated basis to the glow elements designed for 5 V, thus causing the required temperature of 1000 °C to be attained in 2 seconds. The voltage is then gradually reduced in the subsequent actuation intervals to a level much lower than that of the available electrical system voltage.A repeat starting recognition function prevents overheating of the glow elements in the event of several preheating operations in quick succession. On account of the reduced power input of the glow elements, more energy is available to the starter. Individual actuation of the glow elements with power semi-conductors permits comprehensive diagnosis and protection functions.Current A, Voltage V1100 105035 30 25 20 15 10 -2-30 5 10 15 20 25 -430 35 40 5 0Temperature °C1000 950 900 850 -1800 750Voltage profile: Phase 1: Rapid warm-up Phase 2: 7.4 V for 2 seconds Phase 3: 6 V for 8 seconds Phase 4: 5.3 V Temperature profile Current profile Voltage profileTime SSSP290_107 51GearboxGearboxDirect-shift gearbox 02E The direct-shift gearbox (DSG) is basically a parallel gearbox made up of two fully functional manual gearbox units with a joint differential. The engine torque is distributed to the gearbox units via two clutches. One unit selects the even gears and the other the odd gears. Each gear is assigned a conventional manual gearbox synchromesh and shift unit as used by VW and AUDI in manual gearboxes.Refer to Self Study Programme 297 for design and operation.ProCarManuals.comPressurised oil filter Parking lock mechanismOil coolerPump shaftInput shaft 1 Input shaft 2Double clutch Return shaftMechatronic SSP290_11052Technical data Direct-shift gearbox Designation: Max. torque transmission: Operating modes: Gear oil capacity (total): Specification: Total weight: including oil: 02E325 Nm Automatic and Tiptronic6.4 litres ATF G 052 182approx. 80 kgProCarManuals.comThese shift units operate independently. This satisfies the requirement for free gear selection - including even to even and odd to odd gearshift. Gearshift takes place directly, rapidly and with no loss of tractive power.By means of the differential the torque is conveyed to the wheels and, in the case of four-wheel drive vehicles, additionally to the rear axle (via propshaft) by way of the bevel box.Gearbox unit 1642K2R642K1SSP290_111Gearbox unit 253GearboxAutomatic gearbox 09G (6-speed)ProCarManuals.comTechnical data Designation: 09GSSP290_034Manufacturer: AISIN AW CO, LTD Japan Designation: TF-60SN Type: 6-speed planetary gearbox (multi-step automatic gearbox) with electrohydraulic control and hydrodynamic torque converter with slip-controlled torque converter lock-up clutch Front-wheel drive/transverse installation Control: Hydraulic control unit in oil pan with external electronic control unit Dynamic shift program DSP with separate sports program in "Position S" and Tiptronic shift program for manual gear change (optional with Tiptronic steering wheel)Torque/ power: Planetary gearbox ratios (for code letters GSY 1.6 l and GJZ 2.0 l FSI) ATF specification: Capacity:Up to above 300 Nm depending on version 1st gear 2nd gear 3rd gear 4th gear 5th gear 6th gear Reverse 4.148 2.370 1.556 1.155 0.859 0.686 3.394G 052 025 A2 (1 litre) Esso JWS 3309 7.0 litres (fresh fill) lifetime fill approx. 82.5 kgWeight:Overall length: approx. 350 mm Design and operation of the automatic gearbox 09E are described in SSP 291.54Ignition key withdrawal lock Operation With ignition on and selector lever set to position other than P, the ignition key withdrawal lock solenoid N376 is energised. Overcoming spring force, the locking pin of N376 is pressed into the steering lock.Guide sleeveLocking pinSSP290_113ProCarManuals.com- +As long as N376 is energised (locking pin not pressed in), the ignition switch cannot be turned to withdrawal position. The ignition key cannot be removed. After switching off ignition, J527 energises N376 for as long as selector lever is not set to position "P".Locking pin not pressed inSSP290_115Solenoid is deenergised. Ignition key is no longer locked and can be removed.- +Leaving the stationary vehicle for a lengthy period with selector lever set to a position other than P will lead to long-term battery discharge.SSP290_11455Running GearAs opposed to the predecessor model with torsion beam rear axle, the running gear in the Audi A3 ‘04 features a new four-link rear axle with individual suspension. It consists of a broad longitudinal member and a total of three transverse links. This design permits more agile performance as well as improving handling at high levels of lateral acceleration. The basic running gear is equipped with 16-inch wheels whereas 17-inch wheels are fitted for the sports running gear.ProCarManuals.comSSP290_05056Front axleThe 3-part aluminium subframe is designed to accommodate transverse link, anti-roll bar and steering box. Use is made of linear coil springs with progressive polyurethane auxiliary springs as suspension elements. The Audi A3 ‘04 features a bolted thirdgeneration wheel bearing unit (flange bearing with wheel hub as single structural unit). Two drive shafts of equal length are fitted to prevent drive system interference. This necessitated the use of an intermediate shaft (only on vehicles with high drive torque and front-wheel drive as with 2.0 l TDI).Information on design and operation can be found in SSP 313 (Audi A3 ‘04 - Running Gear).ProCarManuals.comSSP290_01657Running GearSteeringElectromechanical steering Use is made for the first time in the Audi A3 ‘04 of an electromechanical steering system with "double pinion" to replace hydraulic power assistance. Advantages: – Reduced fuel consumption thanks to requirement-specific power input – Simple implementation of speeddependent power assistance and damping and thus an optimum steering feel in all situations – Reduced sensitivity to road surface irregularities – Only two hardware versions are now required (LHD/RHD), as adaption is possible by way of software modifications – Active re-positioning of wheels to straight ahead setting – Minimal noise generation in passenger compartment – High rack force levels Power assistance is provided by a separate gear unit which acts on the rack and is driven by an electric motor. A torque sensor located at the torsion bar of the steering wheel determines the torque at the steering pinion. The electric control unit establishes the assistance torque required as a function of torque, vehicle speed, steering angle and steering rate.ProCarManuals.comFlexible attachmentWorm drive Servo pinion Steering box housing Steering shaft connectionBellowsControl unit (ECU) Plug connection Electric motor Steering torque sensor Steering pinion 58Track rodRigid attachment SSP290_051Rear axleRear axle (front-wheel drive) The subframe is made of welded steel and rigidly bolted to the body. The body rests by way of the steel spring on the axle at the deep-drawn steel spring link. The upper transverse link forms the connection between subframe and wheel bearing housing at the upper level. Its T-shaped cross section is primarily designed to absorb lateral forces. Use is made of a cylindrical high-strength steel spring with linear characteristics. The spring is supported by rubber mounts at the body and spring link. The twin-tube gas-filled dampers are mounted well to the outside at the wheel bearing housings. This achieves an optimum 1:1 ratio between wheel travel and damper travel as well as a generous luggage compartment throughloading width.ProCarManuals.comSSP290_017 59Running GearRear axleRear axle for quattro® drive The rear-axle subframe is a welded aluminium structure and at the same time supports the rear final drive. It is bolted to the body by way of amply dimensioned rubber bushes. This method of attachment guarantees good acoustic isolation of the components.Use is made of the same 3rd-generation wheel bearing as at the front axle.ProCarManuals.com3rd-generation wheel bearingSSP290_032Shock absorber Rubber bushesRubber bushPropshaft to rear final drive Subframe SSP290_07760ProCarManuals.comNotes61Electrical SystemBus topologyDiagnostic connection T16 Display unit J285Diagnosis CANData bus diagnostic interface J533Engine control unit J220Door control unit, driver side J386NOx sensor J583Radio RAutomatic gearbox J217Door control unit, front passenger side J387CD changer R41ProCarManuals.comSelector lever sensors J587Parking aid J446Navigation J401ABS with EDL J104Trailer detector J345Telephone transmitter and receiver unit R36Airbag J234Onboard power supply J519Amplifier with bass loudspeaker R44Four-wheel drive J492Convenience electronics J393Additional heater J364Headlight range control J431Additional air heater J604Wiper motor J400Power steering J500Climatronic J255Interior monitor G303Steering angle sender G85 Steering column electronics J527Multifunction steering wheel J453Drive system CAN 500 kbaud Dash panel insert CAN 500 kbaud Diagnosis CAN 500 kbaud Convenience CAN 100 kbaud Infotainment CAN 100 kbaud LIN bus Panasonic busAlarm horn H12Anti-theft/ tilt system J529SSP290_09362Convenience electronicsSelective convenience CAN sleep mode As with the A8 ‘03, wake-up takes place simultaneously for convenience CAN, dash panel insert CAN and infotainment CAN (A8 ‘03:. MOST). On the Audi A3 ‘04, the convenience CAN can be switched to sleep mode independently of the other two CAN buses to save energy. As a result, the dash panel insert J285 and the components linked to the infotainment CAN may continue to transmit data (e.g. brightness value, readings on centre display, navigation data) with the convenience CAN in sleep mode.ProCarManuals.comSSP290_134Information on design and operation can be found in Self Study Programme 312.Load management The wide range of electrical equipment may cause the battery/alternator voltage to drop below a permissible level and thus jeopardise proper functioning of vital systems such as ABS or electromechanical steering. The onboard power supply control unit is able to boost the electrical system voltage to the necessary extent by increasing idling speed and deactivating heavy-duty loads. The alternator is however designed to restrict load management intervention to exceptional circumstances.63Electrical SystemSteering column switch module The design of the steering column switch module has been modified for use in the new Audi A3 ‘04. It includes the following components: – Mechanical ignition switch with immobilizer reading coil D2 – Steering column electronics J527 for signal conversion and processing of signals from drive system and convenience CAN – Equipment-specific control elements – Coil connector with steering angle sender G85 – Electrical ignition key withdrawal lock (on vehicles with automatic gearbox) – LIN function for connection to steering wheel electronics module J453 and operating unit E221 in multifunction steering wheel The task of the steering column electronics is to transmit information from operating elements such as turn signal indicators or wipers to the bus in the form of a CAN message and to read any incoming information.ProCarManuals.comSSP290_09764Onboard power supply control unit The onboard power supply control unit is responsible for the following – – – – – – – – – – Exterior lighting Terminals 15, 75x and 50 Terminal 58s Electric fuel pump relay J17 Windscreen wipers Heated rear window Horn Interior lighting Footwell lights (optional) Load management (no battery energy manager fitted)SSP290_112ProCarManuals.comTester online link The main modification to the diagnostic process is the VAS 5051 online link. Adaption of components forming part of the immobilizer system and radio code call-up are now only possible if the tester is directly linked to the manufacturer's FAZIT data base. PINs will therefore no longer be issued.SSP290_102Further information on the VAS 5051 online link can be found in SSP 294.65Heating/Air ConditionerDesign and operationElectrical load management The heater/air conditioner in the new Audi A3 ‘04 is an advanced system with a new equipment concept. It is characterised by optimised individual components and higher output levels. The electric additional heater J604 is fitted as standard for diesel vehicles with no additional auxiliary heater. The Climatronic control unit J255 is available in versions with/without seat heating and for use with various different radios (slot size 1 or 2 as per DIN). The same applies to use of the heater control unit J65. In the event of an electrical system power "bottleneck" whilst driving, the first step is to increase idling speed. If this is not sufficient, the following heating/ air conditioning loads can be minimised in line with requirements by means of the onboard power supply control unit J519: – Electric additional heater J604 in four stages – Heated rear window Z1 – Seat heating via convenience CAN – Air conditioner on account of consumption-intensive electric fan operationProCarManuals.comSSP290_030 66Heater control panel The heater control unit J65 is of analog type. It is equipped with rotary controls, a flexible shaft for regulating air distribution and a Bowden cable for controlling the temperature flaps. The air-recirculation flap control motor is actuated electrically. It is only supplied with current until the flap reaches its stop position and actuates a limit switch. Air recirculation is deactivated in defroster mode to stop the windows misting up. Seat heating may also be fitted in conjunction with the heater. The driver and front passenger seat heating control units J726/ J727 are then installed at the seats. Only the seat heating potentiometers are integrated into the heater control unit J65. Activation of the heated rear window Z1 is signalled by the heater control unit J65 to the onboard power supply control unit J519, which actuates the LED in the button of the heater control unit J65 following successful activation of the heated rear window. If the heated rear window is defective the LED does not light.ProCarManuals.comDriver seat heating control unit J726Front passenger seat heating control unit J727Term. 75Term. 75Onboard power supply control unit J519 Heater control unit J65Fresh-air/ recirculated-air flap control motor V154Heated rear window Z1Flexible shaft for air distribution Electric additional heater J604Blower with series resistorsTerm. 30 Term. 31 Term. Term. 15 58d Term. 58sEngine control unit J220Bowden cable Series resistor N24 SSP290_02767Heating/Air ConditionerAutomatic air conditioner The automatic air conditioner in the new Audi A3 ‘04 is based on a concept containing modified components. This includes separate driver's and passenger's side temperature regulation with separate sunlight sensors. With this air conditioner, the heated rear window Z1 is controlled by means of the Climatronic control unit J255 and the onboard power supply control unit J519 via the convenience CAN. The enhanced filter concept includes an activated charcoal filter unit in the pollen filter (accessible from front passenger's footwell). The quality of the air in the passenger compartment is thus far better even in recirculated-air mode. Cigarette smoke or evaporator odours can be filtered out.ProCarManuals.comThe Climatronic control unit J255 is available in the versions with and without seat heating as well as 1DIN or 2DIN radio slot height.SSP290_026The air quality sensor G238 is now also available as additional equipment for the Audi A3 ‘04 and is located in the plenum chamber at the front right.Air quality sensorSSP290_03168The air conditioner is operated by a swash plate compressor with 6 reciprocating pistons and regulating valve N280. Use is now also made for control purposes in the new Audi A3 ‘04 of an evaporator outflow temperature sender G263. When the wipers are in operation, the evaporator outflow temperature is reduced to lessen humidity.In the new Audi A3 ‘04, the compressor is not controlled by the fan control unit, but rather by the air conditioner via the Climatronic control unit J255. The radiator fan request is passed via the CAN to the engine control unit, which uses a pulse-width modulated signal to directly actuate either the fan control unit or the fan depending on engine power. The motor of the fresh-air blower V2 is of the brush type and is also controlled via a pulsewidth modulated signal.ProCarManuals.comFor further details of air conditioner components, refer to SSP 240 (Audi A2 - Technical Features) or SSP 254 (Audi A4 ‘01 - Technical Features). Pollen filter for Audi A3 ‘04, model 2004The adjacent illustration indicates the position and fitting location of the pollen filter in the front passenger's footwell.SSP290_117 Design bending pointsPollen filter with design bending points to facilitate replacement in the rather inaccessible footwell area.SSP290_118 69Heating/Air ConditionerMode of operationThe controls for the heated rear window, seat heating and air recirculation are integrated into the Climatronic control unit J255. The heated rear window is controlled by means of the Climatronic control unit J255 and the onboard power supply control unit J519 via the convenience CAN. The basic setting of the control motors used is determined in the course of the "Basic setting" function for the Climatronic control unit J255 by moving from stop to stop. The encoding is also learnt at the same time. This takes place simultaneously for all control motors in the "basic setting" function. After activating the air conditioner, the control unit with display in dash panel insert J285 determines the necessary air throughput automatically in line with the ambient temperature.Fresh-air intake duct temperature sensor G89 Recirculatedair flapProCarManuals.comFresh-air/air-flow flap control motor V71 Centre chest vent Right vent Defrost flap Left vent Left footwell vent temperature sender G261Fresh-air/ air-flow flapDefroster flap control motor V107 Left temperature flap control motor V158 Central flap control motor V70 Rear left footwell flap These two outlets are sealed off for this application. 70Right footwell vent temperature sender G262 Right temperature flap control motor V159 Evaporator outflow temperature sender G263 Rear right footwell flapAir-recirculation flap control motor V113SSP290_028Auxiliary heater deactivation conditions Under the following conditions, the auxiliary heater cannot be started up: – Fuel gauge on zero (only applicable before starting auxiliary heater) – Fault detected for both ambient temperature sensors – Fault memory entry preventing starting – Triggering of crash signalCompressor Depending on vehicle equipment, the compressor is now actuated by the air conditioner instead of the fan control unit. With certain equipment versions, outflow temperature sensors are fitted in the evaporator to control the compressor valves. When the windscreen wipers are in operation, the control unit reduces the evaporator temperature to achieve better dehumidification. Compressor operation is reduced to a minimum after pressing the ECON button, without this affecting energisation of the PTC element. With the recirculated-air button pressed and an ambient temperature of -1 °C, compressor operation is reduced to minimum power. The radiator fan request is passed via the CAN bus from the engine control unit.ProCarManuals.comAuxiliary heater With terminal 15 off, auxiliary heater or auxiliary ventilation mode can be activated depending on ambient temperature by pressing the blower "+" button for at least 2 seconds. Blower delivery has been reduced to a maximum of 4 output stages. Auxiliary heater/auxiliary ventilation is active for a maximum of 62 minutes. If a crash signal has been triggered by the airbag control unit, the additional heater may be disabled for safety reasons. It is then only ready for operation again after deactivating the lock function with the VAS 5051 tester (adaption channel 42).Electric additional air heater Given a heating request from the vehicle occupants, an ambient temperature of less than 7 °C and an engine speed of at least 500 rpm, the additional heater is switched in. This electric additional air heater with a rated power of 1000 W is located in the air flow downstream of the heating system heat exchanger and is fitted as standard on vehicles with diesel engine. If a vehicle is fitted both with a diesel engine and an auxiliary heater as optional extra, the electric additional air heater function is assumed by the auxiliary heater J364. An electric additional air heater is then not fitted.71ServiceSpecial toolsExtractor for unit injector element T10163ProCarManuals.comSSP290_124Oil filter wrench 3417SSP290_125Oil drain adapter T40057SSP290_083 72ProCarManuals.comNotes73ProCarManuals.com74NotesProCarManuals.comVorsprung durch Technik www.audi.deProCarManuals.comAll rights reserved. Subject to technical modification. © AUDI AG I/VK-35 D-85045 Ingolstadt Fax 0841/89-36367 A03.5S00.01.20 Technical status 02/03 Printed in Germany290