TECHNICAL DOCUMENTATION

SSP 226 3,3l V8 TDI Engine Mechanicals

PDFEN36 pages9 MB
SSP 226 3,3l V8 TDI Engine Mechanicals - PDF cover

This PDF is currently unavailable.

Read document text
ProCarManuals.com226Service.3,3 l V8 TDI Engine - MechanicalsDesign and FunctionSelf-Study Programme 226For internal use only 10 years of TDI – The history of the TDI1989Audi presented the first diesel-powered passenger car with direct injection in the Audi 100. The 2.5-ltr. 5 cylinder TDI developed 88 kW (120 bhp) and 265 Nm of torque. A short while later, an 85 kW (115 bhp) version conforming to the US standard valid at that time was launched. This engine was installed in over 20% of the Audi 100/A6 models.1991saw the introduction of the four-cylinder 1.9-ltr. TDI developing 66 kW (90 bhp) and 202 Nm of torque in the Audi 80.1995 ProCarManuals.comThe performance-enhanced version of the 1.9-ltr. TDI developing 81 kW (115 bhp) and 235 Nm of torque came on the market. It was the first direct injection diesel to be equipped with a mapped exhaust gas turbocharger with variable turbine geometry (VTG). The 103 kW (140 bhp) version of the 2.5-ltr. engine developing 290 Nm of torque was presented together with the permanent four-wheel drive quattro. This combination of two typical Audi technologies was to become a meteoric success.1997Audi laid a yet another milestone with the V6 4-valve TDI. It was world's first six-cylinder direct injection engine diesel to be used in a passenger car. It is also the most powerful of the production TDIs, developing 110 kW (150 bhp) and 310 Nm of torque.Audi has revolutionised the popular conception of diesels with its TDI engines, proving that this engine concept can even compete with the petrol engine in terms of dynamics and driving enjoyment, with the added advantage of 30% lower fuel consumption and outstanding bottomend torque. This engine therefore strikes a perfect balance between apparent opposites such as sporty driving on the one hand as well as eco-friendly mobility and long range on the other. Audi perfected these qualities, as exemplified by the five-cylinder TDI from 1989, with theV8 TDI Common Rail2 ContentsPage IntroductionV8 TDI engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5MechanicalsCrankshaft type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Conrod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Four-valve concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Toothed belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14LubricationOil circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crankcase breather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cyclone oil separator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil filter module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 16 17 17ProCarManuals.comCooling circuitOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Main cooling circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Charge air cooling circuit . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel cooling circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic radiator fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 20 21 22 24Air ductingOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vacuum chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Charge air and exhaust gas cooling . . . . . . . . . . . . . . . . . Double-flow throttle valve . . . . . . . . . . . . . . . . . . . . . . . . . . 26 27 28 30 32ServiceSpecial tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33New! The Self-Study Programme informs you about designs and functions. The Self-Study Programme is not a Workshop Manual! Please refer to the relevant technical literature for all maintenance and repair instructions.Important! Note!3 IntroductionV8 TDI engineThe new V8 TDI engine combines exceptional performance with high fuel economy and low exhaust emissions, not to mention extraordinary smoothness and a high standard of comfort.ProCarManuals.comSSP226_0014 SpecificationsCode: Type: AKF V8 engine with 90o V angle and biturbocharging 3328 cm3 165 kW (225 PS) at 4000 rpm 480 Nm at 1800 rpm 78.3 mm 86.4 mm 18.0 : 1 265 kg 1-5-4-8-6-3-7-2 Direct injection with Common Rail System Biturbocharger with variable turbine geometry550 kW 450 400 350 300 250 200 150 480 Nm 165 kW 200 Nm 150 125 100 75 50 25Displacement: Power output: Torque: Bore: Stroke: Compression ratio: Weight: Firing order: Mixture preparation: Exhaust gas turbocharger: Exhaust gas treatment:1000200030001/min5000SSP226_002 Torque (Nm) Power output (kW)ProCarManuals.comBank-specific exhaust gas recirculation with pre- and postoxidation catalytic converters Conforms to exhaust emission standard EU IIIThe maximum torque of 480 Nm is achieved at only 1800 rpm and remains constant at this high level up to an engine speed of 3000 rpm. Max. output is 165 at 4000 rpm.Engine code and engine number are located on cylinder 5 below the exhaust manifold mount.AKF 230 - 2SSP226_037 5 MechanicalsProCarManuals.comSSP226_0036 ProCarManuals.comSSP226_004This diagram can be ordered through Bertelsmann Distribution as a poster in A0 format for a net price of DM 10,00. This offer is valid for Germany only. To order poster in export markets, please contact your importer. Order No.: 507.5317.01.007 MechanicalsProCarManuals.comCrankshaft Main bearing jointThreaded connection/ main bearing jointOil sump upper sectionSSP226_0058 High ignition pressures build up in the area of the main bearing and throughout the bearing block. In addition to the given strength criteria, the crankcase/main bearing joint also had to meet certain acoustic criteria. To meet these requirements, the crankcase for V8 TDI was split in the middle of the crankshaft and a composite construction was chosen for the main bearing part. The main bearing joint (four bolts per bearing) absorbs the high forces exerted on the bearings. The lateral connections of the individual bearing points produce a highly rigid frame which prevents longitudinal vibration of the bearing seats.The oil sump has been raised up to the centre of the bearing. This separates the crankshaft bearing from the oil sump acoustically, minimising noise radiation. The forged crankshaft is made of tempered steel. Two conrods run on a single crank pin. In a V8 engine, with its typical 90o V angle crankshaft and 90o offset, this makes for a uniform spark gap.ProCarManuals.comPistonCooling ductPiston recess of V8 TDIThe piston has a cooling duct for reducing the temperature in the ring area and at the rim of the recess (refer to SSP 183). A wide piston recess is used in combination with a 6-hole injector.Piston recess of V6 TDISSP226_007 9 MechanicalsConrodThrough its trapezoidal shape, the contact surface of the conrod eye and piston hub at the piston pin is larger than the conventional joint between the piston and conrod. Combustion forces are distributed over a larger surface area, reducing conrod and piston pin stress.V6 TDIV8 TDI V6 TDI IIProCarManuals.comSSP226_010 Enlarged contact surfacesHigh voltageThe high combustion pressures of approx. 160 bar are transmitted to the crankshaft via a "sputter bearing“ on the conrod side, as in the V6 TDI. Sputtering is the application of a bearing material using electrical energy. By accelerating the particles of the bearing material from positive to negative, the material is transferred onto the substrate in a highly compressed form at supersonic speed. This final wafer-thin, anti-friction layer has a high surface hardness and exhibits better wear resistance.Argon gas ionsVacuum chamber Bearing material CathodeVacuum pump Anode SSP226_011 Bearing cup mount10 Cylinder headSpring clipSSP226_012ProCarManuals.comSSP226_013Derived from the V6 TDI and provided with an additional cylinder, the cylinder head is of narrow construction due to the constraints on installation space. The intake camshafts are driven by the toothed belt and, in turn, drive the exhaust camshaft by means of helical gears. The valves are actuated via cam followers (refer to SSP 183).The injectors are secured by elastic spring clips. Thismakes a precisely defined and uniform load with low distortion possible whether the engine is cold or hot. The common rail injectors are installed in the upright position midway between the exhaust and intake valves.11 MechanicalsThe injectors are sealed off from combustion chamber by means of a sealing disc. If a leak occurs, excess combustion pressure can escape into the atmosphere along the duct. This prevents large amounts of gas flowing to the compressor side of the exhaust gas turbocharger via the crankcase breather and causing it to malfunction.ProCarManuals.comExcess pressure relief in the event of leaks at the injector SSP226_018 Sealing discCylinder head cover The isolation of the cylinder head cover serves as soundproofing (refer to SSP 217). The injectors are sealed by separate cover plates with an injection-moulded elastomersealing lip.Elastomer sealing lipSealing ring on injectorDuring installation, the transitions from straight surfaces to curved surfaces have to be sealed with a special sealing compound (refer to Workshop Manual).SSP226_03212 Four-valve conceptFilling duct Tumble ductInjectorProCarManuals.comTwin-pipe ductSSP226_015The 4-valve arrangement known from the V6 TDI engine with – two intake ports per cylinder (tumble duct and filling duct) – two exhaust ports per cylinder (twin-pipe duct) – central, upright injector position – central combustion chamber – rotated valve position for better thermodynamics was adopted unchanged.13 MechanicalsToothed belt driveHigh-pressure pumpCamshaft gear wheelDeflection pulleyCamshaft gear wheelProCarManuals.comExcentric rollerToothed belt tensionerSSP226_014Camshaft gearThe high-pressure pump drive is integrated in the toothed belt drive. The toothed belt guide was modified compared to the V8 5V engine for this reason. It requires an additional deflection pulley but does without a stabilising pulley. Use special tool 3458 of the V6 TDI to fix the camshaft (refer to Workshop Manual).Installation positions need not be observed when installing the highpressure pump.14 LubricationOil circuitCylinder bank 1 Vacuum pump Oil pressure limiting valveCylinder bank 2RestrictorCamshaft Oil pressure limiting valveOil retaining valveInjectorProCarManuals.comExhaust gas turbo-chargerExhaust gas turbochargerOil filter module Filter elementOil sump Oil cooler Bypass valves Oil pressure control valve Duocentric oil pump Oil curve without pressure Oil curve with pressure SSP226_01615 LubricationCrankcase breatherIn charged diesel engines, so-called blow-by gases occur as a result of leakage flows at the piston rings. These gases are discharged from the combustion chamber and flow into the crankcase. They have to be burned for ecological reasons.Exhaust gas turbochargerCharge air coolerProCarManuals.comCyclone oil filterBlow-by gasesValve piston Turbulence caused by blow-by gases and crankshaft web “drag”SSP226_030The oil spray drawn off the crankcase precipitates droplet by droplet in the evaporation line and flows back into the crankcase.16 Cyclone oil separatorThe blow-by gases are fed along a line into the oil separator from the inner V of the engine. The swirling movement of the gases inside the oil separator separates the oil from the gases because the oil exhibits inertia. The oil-free blow-by gases now enter in the intake duct upstream of the left turbocharger and are then burned. The membrane integrated in the cyclone filter cover is used to control the vacuum in the crankcase. If the suction capacity in the intake duct exceeds the pressure in the crankcase, the membrane closes the turbocharger suction port. This prevents oil from entering the intake duct.Flow to intake duct closedMembraneTo intake ductSSP226_031 from crankcaseProCarManuals.comSSP226_034Oil filter moduleThe oil filter module is largely identical to that used in the 4.2-litre petrol engine. The oil filter housing has been extended upwards by approx. 30 mm in order to absorb a larger quantity of oil and to mount a larger oil filter cartridge for long life service.30 mmSSP226_01717 Cooling circuitOverviewProCarManuals.com18 ProCarManuals.comSSP226_019The cooling circuit is subdivided into three areas: high-temperature low-temperature low-temperature - main cooling circuit - charge air cooling circuit - fuel cooling circuit19 Cooling circuitMain cooling circuitThe engine cooling and EGR cooling systems are integrated in the high-temperature circuit.EGR cooler supply line Cylinder head front left Coolant temperature senders G2 and G62 Permanent ventilationEGR cooler return line Heating return line Heating supply line Expansion tank, topCylinder head, rear rightProCarManuals.comWater pump supply line Thermostat housing Filling hose for fuel cooling circuitOil filter return lineExpansion tank, bottom Main cooler ventMain cooler return line (main cooling circuit) Cross-member with connection Main cooler supply line (main cooling circuit)Filling hose for charge air cooling circuit Connection engine block SSP226_02020 Charge air cooling circuitThe charge air cooling circuit is connected to the main cooling circuit by a filling hose and has its own additional electrical coolant pump and an additional cooler (air - water). The charge air cooling circuit also has a lowtemperature area in the main cooler.Charge air cooler return lineCharge air cooler supply lineProCarManuals.comBleeder hoseAdditional coolerFilling hoseAdditional coolant pump V188 Main cooler supply line (charge air cooling circuit) Main cooler return line (charge air cooling circuit)SSP226_02121 Fuel cooling circuitIt is important that the fuel enters the return line cooled, because of the high temperature which builds up when the diesel fuel is compressed (the temperature rises to approx. 1350 bar). The heat exchanger for diesel fuel is integrated in the return line. The increased temperature of the fuel is dissipated to the cooling water flowing through the cooling circuit. The additional electrical coolant pump delivers the heated coolant back to the heat exchanger through an additional cooler. The fuel cooling circuit is connected to the return line of the main cooling circuit along the filling hose.Heat exchanger for diesel fuelVent screwProCarManuals.comFilling hoseSupply lineAdditional cooler Return lineAdditional coolant pump V166SSP226_022The additional electrical coolant pump runs continuously after the engine is started.22 Vent screwto additional coolerFuel to tank Fuel from injectorsfrom additional coolant pumpSSP226_029ProCarManuals.comFuel cooling (air) The fuel is cooled additionally by a specially shaped return line located on the underside of the vehicle. The aluminium profile provides a large cooling surface because of its shape. The radial longitudinal grooves in the interior of the return line are conducive to heat transfer from the fuel to the cooling profile.Cooling profile Vehicle underbodySupply lineReturn lineSSP226_03523 Cooling circuitHydraulic radiator fanA hydraulic radiator fan system is used in order to utilise of the heat balance fully. The system components include: – Tandem hydraulic pump – Solenoid valve for radiator fan control N313 – Radiator fan with hydraulic motor – Oil tank – Oil coolerProCarManuals.comEngine control unit J248Oil tankTandem hydraulic pumpSolenoid valve for radiator fan control N313Steering gearRadiator fan with hydraulic motorOil cooler SSP226_00824 Driven by the ribbed V-belt, the tandem hydraulic pump supplies the power steering and the hydraulic fan with oil pressure simultaneously.A regulating valve cycled by the engine control unit conveys a specific quantity of oil to the hydraulic motor in dependence upon engine temperature and speed.Pressure connection for steering gearReturnProCarManuals.comSSP226_009 Pressure connection for hydraulic motor Solenoid valve for radiator fan control N313The internal geared wheel connected directly to the fan is driven by this quantity of oil. The oil flows along the return line and into the intake line of the hydraulic tandem pump.Trochoidal internal geared wheel of hydraulic motorOil pump cover with pressure and discharge ducts SSP226_036SSP226_02325 Air ductingOverviewIntake module with integrated charge air cooling and EGR coolingAir inlet from air filterCharge pressure sender G71ProCarManuals.comEGR valveEGR valveExhaust manifoldHot-film air mass meter G70/G246Exhaust gas turbochargerSSP226_028 Vacuum box for vane adjustment26 ChargingTwo small exhaust gas turbochargers with a variable turbine geometry are used in the V8 TDI engine for charging purposes.Advantage: Using a small turbocharger improves the bottom-end torque curve.The turbocharger controls the charge pressure through bank-specific air flow metering by means of two hot-film air mass meters. The variable guide vanes of the turbocharger are actuated by means of vacuum boxes activated by electro-pneumatic valves. To optimally utilise exhaust gas energy specifically in the warm-up period while ensuring that exhaust emissions conform to the EU III limit values, the manifolds for each cylinder bank are joined in a cloverleaf pattern and are insulated from the outer skin of the body-shell by an air gap.The two independent air intake ducts are cooled by the turbocharger in a common intake module after the air is compressed. Each of these ducts supplies air to a single cylinder bank. To be able to realise a highly compact engine design, the intake module was positioned in the inner V of the engine. In addition to ducting the intake air, the intake module contains a combined charge-air and EGR cooler module..ProCarManuals.comThe turbochargers may be replaced individually.27 Air ductingVacuum chartJ248G70G246ProCarManuals.comAN213 G2/G62 G28 G40N18NG71C28 A B CVacuum pump Brake servo Throttle valvesG2/G60 Coolant temperature sender G28 G40 G70 G71 G246 Engine speed sender Hall sender Air-mass flow meter Charge pressure sender Air-mass flow meter2 Diesel direct injection system control unit EGR valve, cylinder bank1 Solenoid valve for charge pressure control EGR valve, cylinder bank 2 Solenoid valve 2 for charge pressure control Intake manifold changeover valvesProCarManuals.comJ248BN18N75N213N274N239N75 N239N274SSP226_027 29 Air ductingCharge air and exhaust gas coolingThe charge air and EGR cooling systems are combined in a single module comprising two separate cooling circuits; the cooled air downstream of the two throttle valves is fed into the engine bank by bank.Advantage: The water-air cooling system achieves the same charge-air cooling effect with considerably less loss of charge pressure. Also, better efficiency is achieved in the reheating phase and when driving uphill.EGR valves N18/N213Solenoid valve for throttle valve N239ProCarManuals.comEGR valveEGR valveEGR coolerCharge air coolerCharge air inletThrottle valves 30SSP226_024 To reduce NOx and particle emissions still further, the exhaust gas recirculated in the V8 TDI is additionally cooled by an air-water cooler.EGR valves EGR valvesProCarManuals.comExhaust gasIntake pipe Cylinder 1 Intake pipe Cylinder 7 EGR cooling Cooling the charge airCharge airSSP226_02531 Air ductingDouble-flow throttle valveThe double-flow throttle valve is closed when the engine is shut down for a short period of time. Advantages: The engine does not run on after it has been shut down and no unburned fuel enters the cylinders (when the engine is restarted, fewer unburned particles are emitted).ProCarManuals.comThrottle valveCharge pressure sender G71SSP226_026 Vacuum box for throttle valve positioningIn normal position and at full throttle, the two throttle valves are fully open. If the EGR system is active, the valve moves into intermediate positions so the fuel mixes better with the induced air.32 ServiceSpecial toolsShown below are the new specialtools and workshop equipment for the 3.3-ltr. V8 TDI engine.ProCarManuals.comSpecial tool for valve removal Pressure piece VW 541/6 Adapter for assembly fixture 2036/1Compression test adapter V.A.G. 1763/5Setting gauge for camshaft retainer 3458Test box for V6-TDI V.A.G 1598/3033 ProCarManuals.com34Notes ProCarManuals.comNotes35 ProCarManuals.comAll rights reserved. Technical specifications subject to change without notice. AUDI AG Dept. I/VK-5 D-85045 Ingolstadt Fax +49 841/89-36367 940.2810.45.20 Technical status 07/99 Printed in Germany226