TECHNICAL DOCUMENTATION

SSP 287 Audi A8 ’03 – Electrical Components

PDFEN96 pages2 MB
SSP 287 Audi A8 ’03 – Electrical Components - PDF cover

This PDF is currently unavailable.

Read document text
287Service.AUDI A8 '03 - Electrical ComponentsSelf Study Programme 287For internal use only Definition of terms Data bus network (topology) The topology provides a general outline of the way in which control units fitted in the vehicle are interlinked by way of data bus systems. It thus becomes clear which bus systems are used by the control units to exchange data. Distributed functions Function masterThis Self Study Programme contains information on data bus networking (topology) and electrical components in the Audi A8 ´03. With distributed functions, one control unit is always responsible for the entire sequence of operations. The function master control unit gathers all input information. The requests resulting from this are then transmitted in the form of a message on the data bus system and read into the control units concerned for corresponding actuation of the appropriate connected components. Substitute masterThis introduction contains explanatory notes to clarify the meanings of certain terms, designations and symbols used in this Self Study Programme.An understanding of the interaction of the components and distributed functions forms the necessary basis for successful fault-finding.More detailed information can be found in the following Self Study Programmes:– SSP 282 – Audi A8 ´03 Technical Features – SSP 286 – New Data Bus Systems – LIN, MOST, BluetoothTM – SSP 288 – Audi A8 ´03 Distributed Functions – SSP 289 – Adaptive cruise control in the Audi A8 ´03 – SSP 293 – Audi A8 ´03 Infotainment This term indicates that several control units are required to exchange information in order to implement a function.WiringConvenience CANComponents and symbolsDrive system CANAdaptive cruise control CAN Example: Wiper speed 1 function1In the event of function master failure affecting major functions, the task of the function master is assumed by a control unit provided for this purpose and designed to maintain the sequence of operations (possibly with certain restrictions).Dash panel insert CANMOST busA number is used to designate the information sequence described in the corresponding text. The green circle symbolises the start of an information sequence.LIN busJ400Diagnosis CAN The green arrow indicates input information.J519 E22Bidirectional wireReception wire The blue arrow indicates output information.J527Transmission wireDiscrete wireJ518Ignition ON SSP287_005Wireless transmission – transmission signalWireless transmission – reception signalPrerequisite 2 The steering column electronics transmits the information "Wiper speed 1" to the onboard power supply control unit J519. Ignition switched on by way of electric ignition/starter switch or Advanced Key, so that entry and start authorisation control unit J518 transmits terminal 15 and 75x information to convenience CAN. 1 The intermittent wiper switch E22 transmits the information "Wiper speed 1" to the steering column electronics control unit J527. 3 The onboard power supply control unit transmits the information "Wiper speed 1" via the LIN to the wiper motor control unit J400. The wiper motor control unit actuates the integrated motor.Follow-up functionThe layout of the individual components such as control units, switches or control elements as illustrated corresponds to the actual arrangement in the vehicle. Component designations are explained on the basis of their identifiers in the relevant text.Prerequisite Components marked in red indicate the function master within a sequence of operations.Components marked in yellow indicate the substitute master. ContentsPage Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Control UnitsDrive system CAN/convenience CAN connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Data bus diagnostic interface J533 (gateway) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Energy management control unit J644 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Control unit with display in dash panel insert J285 . . . . . . . . . . . . . . . . . . . . . . . . 38 Convenience system central control unit J393 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Boot lid control unit J605 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Anti-theft/tilt system control unit J529 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Onboard power supply control unit J519 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Wiper motor control unit J400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Onboard power supply control unit 2 J520 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Door control units J386 to J389 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Sunroof electronics control unit J528 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Garage door operation control unit J530. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Entry and start authorisation control unit J518 . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Driver identification control unit J589 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88The Self Study Programme contains information on design features and functions. The Self Study Programme is not intended as a Workshop Manual. Values given are only intended to help explain the subject matter and relate to the software version applicable at the time of SSP compilation. Use should always be made of the latest technical publications when performing maintenance and repair work.NewAttention Note3 IntroductionBus topologyControl unit with display in dash panel insert J285Distance regulation control unit J428Diagnostic connection T16Dash panel insert CAN (500 kbit/s)Electric park and handbrake control unit J540Headlight range control unit J431Airbag control unit J234ABS with EDL control unit J104Engine electronics 1 J623Engine electronics 2 J624Adaptive suspension control unit J197Automatic gearbox control unit J217Internal bus linkAnti-theft/ tilt system control unit J529Boot lid control unit J605Wiper motor control unit J400Garage door operation control unit J530Multifunction steering wheel E221LIN (20 kbit/s)Convenenience system central control unit J393Onboard power supply control unit J519Onboard power supply control unit 2 J520Steering column electronics control unit J527Steering angle sender G85Door control unit, driver side J386Door control unit, front passenger side J387Door control unit, rear left J388Door control unit, rear right J389Seat adjustment control unit J1364Drive system CAN (500 kbit/s)Seat adjustment control unit, front passenger J521Diagnosis CAN (500 kbit/s) BluetoothTMRear DVD changer R162 Telephone/ telematics control unit J526 Telephone handset R37Adaptive cruise control CAN (500 kbit/s)Control unit for rear right information display and operating unit J649Control unit for rear left information display and operating unit J648Front information display and operating unit control unit J523DSP control unit J525Data bus diagnostic interface J533MOST bus (21 Mbit/s)Navigation control unit J401CD ROM drive R92TV tuner R78Convenience CAN (100 kbit/s)CD changer R41Digital radio R147Chip card reader control unit J676Radio module RFresh-air blower control unit J126Heated windscreen control unit J505Rear left footwell heater element Z42Rear right footwell heater element Z43Driver seat ventilation control unit J672Front passenger seat ventilation control unit J673LINClimatronic control unit J255Rear seat adjustment with memory control unit J522Trailer detector control unit J345Energy management control unit J644Entry and start authorisation control unit J518Parking aid control unit J446Rear Climatronic control and display unit E265Tyre pressure monitor control unit J502Sunroof electronics control unit J528Additional heater control unit J364Driver identification control unit J589LINDriver side rear seat ventilation control unit J674Front passenger side rear seat ventilation control unit J675Sliding sunroof motor V1Auxiliary heating radio controlled receiver R64SSP287_057 5 Control UnitsDrive system CAN/ convenience CAN connectorsConnectorConvenience CAN contact links CAN wiringLink SSP287_014 Catch Drive system CAN contact linksTwo CAN bus connectors are used in the Audi A8 ´03. The connectors form the central junction for both the convenience and the drive system CAN.All CAN wires of the respective bus system control units are attached to the connectors.6 Fitting locations The connectors are installed on the right and left sides of the dash panel behind the end trim. The catch has to be unfastened before a link can be detached. The pin assignments of the two connectors are different in left and right-hand drive vehicles.The pin assignments can be found in the appropriate Workshop Manual or under "Vehicle information" in assisted faultfinding.SSP287_015SSP287_0167 Control UnitsStar connection All drive system and convenience CAN control units are linked to the corresponding connector in star configuration. Some of the control units of a bus system are linked to the right connector, whereas the others are linked to the left connector. In turn, the left and right connectors are interlinked by a CAN wire so that ultimately all convenience CAN control units are interlinked, as are those of the drive system CAN.Convenience CAN wireDrive system CAN wireFront passenger side CAN connectorDriver side CAN connectorSSP287_017 CAN wires to control units CAN wires to control unitsTest box Use is made for the CAN connectors of the test box 1598/38. This test box makes it possible to access the individual drive system and convenience CAN control unit wires with the digital storage oscilloscope of VAS 5051. Individual control units can also be disconnected from the bus system during fault-finding. This is necessary, for example, when trying to localise CAN bus short circuits. The link connecting the CAN wires of the individual control units is inserted at the test box and can also be checked.8 Block diagramT46a J527 J386 J388 J446 J345 J502 J136 J518 J524 J519 J527 J104 J234 J431J533 J387 J389 J520 J393 J644 J364 J528 J521 J522 J589 J255J533 J540 J217 J623 J197T46bSSP287_018Key J104 ABS with EDL control unit J136 Seat adjustment with memory control unit J197 Adaptive suspension control unit J217 Automatic gearbox control unit J234 Airbag control unit J255 Climatronic control unit J345 Trailer detector control unit J364 Additional heater control unit J386 Door control unit, driver side J387 Door control unit, front passenger side J388 Door control unit, rear left J389 Door control unit, rear right J393 Convenience system central control unit J431 Headlight range control unit J446 Parking aid control unit J502 Tyre pressure monitor control unit J518 Entry and start authorisation control unit J519 Onboard power supply control unit J520 Onboard power supply control unit 2 J521 Seat adjustment with memory control unit, front passenger J522 Seat adjustment with memory control unit, rear J524 Rear information display and operating unit control unit J527 Steering column electronics control unit J528 Sunroof electronics control unit J533 Data bus diagnostic interface J540 Electric park and handbrake control unit J589 Driver identification control unit J623 Engine control unit J644 Energy management control unit T46a 46-pin, black connector at left CAN breaker T46b 46-pin, black connector at right CAN breaker Colour code = Convenience CAN High = Convenience CAN Low = Drive system CAN High = Drive system CAN Low9 Control UnitsData bus diagnostic interface J533 (gateway)The wide range of interlinked vehicle functions necessitates the use of several data bus systems on account of the capacity required for handling the great volume of data to be transmitted. The data bus diagnostic interface is a network gateway for data bus systems, the principal function of which is to form the interface between the various independent data bus systems in the vehicle. In the past, the gateway function was integrated into the dash panel insert. A separate control unit is employed in the Audi A8 ´03 to cope with the large number of functions distributed over various control units and requiring a high level of data transfer between the control units of the different bus systems.Diagnosis CAN 500 kbit/s Dash panel insert CAN 500 kbit/sDrive system CAN 500 kbit/s MOST 21 Mbit/sAdaptive cruise control CAN 500 kbit/s (optional)Convenience CAN 100 kbit/sSSP287_001Versions Two different data bus diagnostic interface J533 versions are used in the Audi A8 ´03: One with connection to the optional adaptive cruise control (ACC) system and the other without this connection. Both versions however feature a connection for the MOST optical data bus fitted as standard.SSP287_002 Electrical connection Optical output Optical input10 Fitting location In the Audi A8 ´03, the data bus diagnostic interface is installed at the module holder behind the glove box.SSP287_004Block diagram J533 Data bus diagnostic interfaceDiagnosis CAN Ring fault Dash panel diagnosis insert wake-up wire301531J533SSP287_003 Drive system Convenience CAN CAN Dash panel insert CAN Adaptive cruise control CAN (optional) MOST bus11 Control UnitsData exchangeExample: Transmission from terminal 15E408 Control units connected to MOST busJ518 J533 J285E415Control units connected to convenience CANControl units connected to drive system CANSSP287_006The data bus diagnostic interface J533 implements the exchange of data between the various data bus systems.To do so, it transmits data with a short propagation time from one data bus system to the other. In this process, not all data from one bus system are transmitted to the next, but rather only the data required by the system concerned.1a The terminal 15 information is transmitted by the entry and start authorisation button E408 via a discrete wire to the entry and start authorisation control unit J518. or 1b Transmission from terminal 15 to the entry and start authorisation control unit J518 is effected via a discrete wire by actuating the entry and start authorisation switch E415.122The entry and start authorisation control unit relays the information via the convenience CAN to the data bus diagnostic interface. The information is read in by the data bus diagnostic interface J533 and transmitted to the drive system CAN, dash panel insert CAN (control unit with display in dash panel insert J285) and MOST bus. The information is thus available to all connected control units.3 Master functions The data bus diagnostic interface is the master for: – Drive system CAN continued operation – MOST ring fault diagnosis – Data bus system sleep and wake-up Drive system CAN continued operation Terminal 15 continued operation for various control units connected to the drive system CAN (refer to entry and start authorisation control unit) is sustained until the data bus diagnostic interface transmits a command for termination of continued operation to the drive system CAN. MOST ring fault diagnosis The data bus diagnostic interface is the diagnosis manager for the MOST bus. This is responsible for ring fault diagnosis and transmits the diagnosis data of the control units in the MOST bus to the data bus diagnostic interface. Ring fault diagnosis for the MOST bus is initiated by way of the final control diagnosis in the data bus diagnostic interface (refer to SSP 286 - New Data Bus Systems, Page 41 onwards).Diagnostic wireSleep and wake-up mode The data bus diagnostic interface is the master for sleep and wake-up modes in the vehicle. When all control units connected to the convenience CAN indicate "sleep readiness", the gateway transmits the sleep command to the CAN bus and the connected control units switch to sleep status. The sleep status of the individual control units and bus systems can be read out in the Audi A8 '03 from the measured value blocks of the data bus diagnostic interface.Data bus diagnostic interfaceDiagnostic connectionSSP287_007 Break in optical fibre 13 Control UnitsDiagnosis The data bus diagnostic interface enables data to be exchanged between the diagnosis unit and the individual control units in the vehicle. In this process, the control unit diagnosis data are transmitted via the corresponding data bus system to the diagnostic interface and from there via the diagnostic connector to the diagnosis unit (refer to SSP 286 under "Diagnosis CAN", Page 50). The data bus diagnostic interface retains diagnostic capability even without terminal 15 ON. This is however subject to the restriction that no write operations, such as encoding, can be implemented. The ignition must be on for starting diagnosis, as the 500 kbit/s diagnosis CAN has no wakeup capability.Measured value blocks The data bus diagnostic interface is provided with measured value blocks in which communication, one-wire diagnosis and sleep mode are displayed. If there is communication with a control unit fitted in the vehicle, this is indicated in the measured value block by a 1. If there is no communication with a control unit fitted in the vehicle or encoded, this is indicated by a 0. If a control unit is in one wire mode, this is indicated by "1 wire". In the Audi A8 ´03, the measured value block for one-wire diagnosis is only available in the diagnostic interface. The "sleep readiness" of the control units is indicated by "S". If the vehicle is in diagnosis mode, the bus systems do not switch to sleep mode even if all control units are indicating "sleep readiness".Assisted fault-finding Functional test J533 - Display measured value blocksAudi V05.02 18/06/2002 Audi A8 2003 2003 (3) Saloon BFM 4.2l Motronic / 246 kWMeasured value block 130 Two-wire Convenience data bus Electr. CE 1 Electronic central electrics Central 0 Convenience system central module Driver's door 1 wire Driver's door electronics1.Functional descriptionMeasurementJumpPrintHelpSSP287_010 14 Control element test The following control element tests are available in the data bus diagnostic interface as part of assisted fault-finding: – Start of ring fault diagnosis (refer to SSP 286, Page 41) – Start of ring fault diagnosis with dB reduction (refer to SSP 286, Page 43) – Transmission of sleep command On transmitting the sleep command by way of the final control diagnosis (terminal 15 must be off), the drive system CAN and convenience CAN are switched to sleep mode by the data bus diagnostic interface. Switching of the convenience CAN to sleep mode is however only possible if no other control unit is keeping the bus awake, for example on account of a fault.Gateway fitting list On entering diagnosis mode, a detailed list containing the control units fitted in the vehicle and their current status is read out from the data bus diagnostic interface. The gateway fitting list can be displayed in the self-diagnosis main menu or via assisted fault-finding. The fitting list (also referred to as configuration table) shows whether all control units have been properly encoded, as well as their fault status. If, for example, a control unit has been fitted but not encoded, this is indicated in the fitting list as "Not registered". If a control unit has been encoded, but there is no communication with it, this may be due to a fault or non-installation. This control unit is then labelled "Not obtainable".Vehicle self-diagnosis Gateway fitting listAudi V05.02 18/06/2002 Audi A8 2003 2003 (3) Saloon Communication link BFM 4.2l Motronic / 246 kW 01 - Engine electronics OK 61 - Battery control Fault 02 - Gearbox electronics OK 42 - Driver's door electronics Fault 52 - Front passenger's door electronics OK 62 - Rear left door electronics Fault 72 - Rear right door electronics Fault 03 - Brake electronics Fault 53 - Parking brake Fault 34 - Adaptive suspension OK 05 - Entry and start authorisation OK 15 - Airbag Fault 55 - Headlight range control FaultMeasurement Jump Print HelpVAS display OK Not obtainableSignificance Communication OK The control unit is registered (encoded) in the gateway but there is no communication with it A fault entry has been stored in the control unit The control unit is not registered in the gateway (not encoded), but it has been fitted/there is communication with this control unitFault Not registeredSSP287_01215 Control UnitsEncoding The encoding informs the data bus diagnostic interface of which control units are fitted in the vehicle. In addition to the familiar encoding, the function "Read/write long encoding" is provided in the diagnostic interface. After selecting this function, a list containing the address words of all possible control units in the vehicle is called up in the diagnosis tester in the usual sequence. Control units can then be selected/rejected. Pressing the "Continue" key transfers the encoding to the control unit. After encoding the diagnostic interface with "long encoding", a fitting list should be read out to check whether all control units in the vehicle have been correctly encoded in the gateway.Vehicle self-diagnosis Read/write long encoding19 - Data bus diagnostic interface 4E0910468 4E0907468- * Gateway H04 X200 Long encoding Dealership number 6794 Encoded Encoded Encoded Encoded Encoded Encoded Encoded Encoded Encoded Not encoded Encoded Encoded Encoded EncodedPrint Help01 - Engine electronics 61 - Battery control 02 - Gearbox electronics 42 - Driver's door electronics 52 - Front passenger's door electronics 62 - Rear left door electronics 72 - Rear right door electronics 03 - Brake electronics 53 - Parking brake 34 - Adaptive suspension 05 - Entry and start authorisation 15 - Airbag 55 - Headlight range control 65 - Tyre pressure monitoringMeasurement JumpSSP287_01316 Energy management control unit J644Use is made for the first time in the Audi A8 ´03 of a battery and energy management control unit. The increase in the number of electronic components and controls in the vehicle gives rise to a far greater power requirement. The uncontrolled tapping of power can cause a major drop in the level of electrical energy available in all vehicle statuses. The principal tasks of the energy management control unit are to monitor the battery charge, to regulate loads via the CAN in extreme circumstances, to minimise current consumption by deactivating functions and to ensure optimum charging voltage. The aim is to avoid excessive battery discharge and thus ensure that the vehicle can always be started.SSP287_039Fitting location The energy management control unit J644 is installed on the right of the luggage compartment in the immediate vicinity of the battery.Functions The energy management control unit J644 is responsible for constant monitoring of the battery, which includes checking the state of charge (SOC) and starting capability. The control unit regulates the optimum alternator charging voltage with the engine running. It can implement load shedding (reduce the number of loads) and increase idling speed. To reduce the closed-circuit current with the engine OFF, the energy management control unit can deactivate loads via the CAN in extreme circumstances and thus prevent excessive battery discharge.SSP287_02517 Control UnitsBlock diagram30 1512+ A J655J64435 4GMC 31BSSP287_041Key A B C J644 J655 Battery Starter Alternator Energy management control unit Battery cut-off relayAdditional signals 1 Airbag control unit J234 2 Airbag control unit J234 3 Convenience CAN High 4 Convenience CAN Low 5 Terminal 50 (from starter relay 2 J695)18 System outline CAN inputs CAN outputs– – – – – – – – – – –Ambient temperature Engine speed Coolant temperature Standing time Ignition/starter switch Heated windscreen Heated rear window Specified idling speed feedback Load shedding request Heating system load shedding Alternator activation– – – – – – – – – – – –Convenience CAN HighConvenience CAN Low– – – – – – – –Drive system deactivation stage Idling speed increase Deactivation stages Load shedding Alternator load torque Alternator power input Battery manager/battery voltage Heating system deactivation Charge Starting capability Deactivation stage 6 Terminal DFM – BEM (battery energy manager) Load shedding feedback Alternator load response Alternator fault Infotainment deactivation Battery manager service fault Heavy-duty heating system status Heavy-duty heating system control status Emergency load deactivation activeInputs via BSI*Outputs via BSI*– DF signal (alternator capacity utilisation) – Alternator mechanical fault – Alternator electrical fault – Alternator high-temperature regulation– Specified alternator voltage – Start load response – Drive load response* BSI = Bit-synchronous interface19 Control UnitsFunction modules The tasks of the energy management control unit J644 are distributed over three function modules, which are active in different vehicle statuses. Function module 1 is the battery manager. This is responsible for battery diagnosis (always active). Function module 2 is the closed-circuit manager. It deactivates "standing" loads as required (engine not running). Function module 3 is responsible for dynamic management, in other words for charging voltage regulation and load reduction (engine running). Energy management control unitFunction module 1 Battery manager Battery diagnosisFunction module 2 Closed-circuit manager "Standing" load deactivation Function module 3 Dynamic management Charging voltage regulation Load reductionFunction module action The three function modules are active in specific vehicle statuses. A distinction is made between three vehicle statuses:Vehicle status Terminal 15 OFF Terminal 15 ON, engine not running Terminal 15 ON, engine runningBattery manager Active Active ActiveClosed circuit manager Active ActiveDynamic managementActive20 Battery manager For implementation of battery diagnosis, the battery manager in the energy management control unit has to establish the following data: – – – – Battery temperature Battery voltage Battery current Operating timesBattery temperature -35 - 70 °CFor display: – State of charge (SOC) – Starting capability forecast For current consumption control: – Deactivation stages For alternator: – Optimum charging voltage Alternator emergency reserve: – Regulation of heavy-duty and heating systemsBattery voltage 5.5 - 16 VBattery current 10 mA - 100 AOperating times Energy management control unit J644The battery current and battery temperature are measured in the control unit and the battery temperature converted to the battery by means of an algorithm. The battery voltage on the other hand is measured at the battery positive terminal.21 Control UnitsBattery status display The starting capability and current charge are displayed in the dash panel insert. These two quantities form the basis for closed-circuit and dynamic management. The alternator is provided with the optimum charging voltage via an interface.Battery weakPR N D SMMI displays The battery charge can be called up via the CAR function in the MMI. The display takes the form of a bar with 10 % increments. A charge of between 60 and 80 % is normal.UserCar ChargeLogbookSystemsTP TMCMaintenanceRunning electrical loads over a lengthy period with the engine switched off discharges the battery. If the starting capability of the engine is jeopardised by this, the MMI displays a request to start the engine to prevent automatic system deactivation in the next three minutes.SSP287_042Car Starting capabilityPlease start engine, as otherwise system will be deactivated in 3 minutes.Charge warning lamp (alternator lamp) The charge warning lamp is located in the rev counter in the dash panel insert. In contrast to previous Audi vehicles, the lamp is however actuated by the energy management control unit.TPSSP287_121SSP287_10222 Closed-circuit manager The function of the closed-circuit manager in the energy management control unit J644 is to request control units to deactivate loads as required. It is active with terminal 15 OFF and terminal 15 ON/engine OFF. If the vehicle is stationary, the closed-circuit current must be reduced to such an extent that the battery is only slightly discharged and starting is possible even after a long standing time. If the battery charge is not sufficient to be able to supply all "standing" loads, convenience and infotainment load functions are deactivated. The loads to be deactivated by a control unit are specified in deactivation stages on a hierarchical basis (refer to Page 28). The loads/functions deactivated by a control unit are indicated under "Vehicle information" in the assisted fault-finding routine. Control unit loads are deactivated in six stages. The lower the battery charge, the higher the deactivation stage. The necessary deactivation stage is provided by the energy management control unit via the data bus systems. The dash panel insert informs the driver of restrictions to functions. As regards diagnosis, it should be remembered that an activated deactivation stage may be the cause of a restricted function. Activation of a deactivation stage is stored as a fault in the fault memory of the energy management control unit.Assisted fault-finding Function/component selectionAudi V05.02 18/06/2002 Audi A8 2003 2003 (3) Saloon BFM 4.2l Motronic / 246 kWVehicle information Dynamic and closed-circuit management General Closed-circuit deactivation stage 1 Closed-circuit deactivation stage 2 Closed-circuit deactivation stage 3 Closed-circuit deactivation stage 4 Closed-circuit deactivation stage 5 Closed-circuit deactivation stage 6MeasurementVehicle self-diagnosisJumpPrintHelpSSP287_061 23 Control UnitsDeactivation stages The individual deactivation stages are initiated by the energy management control unit in line with the charge of the vehicle battery. The deactivation stages result in the following: – Deactivation stage 1 Convenience CAN loads are deactivated. – Deactivation stage 2 Initiation of this stage results in deactivation of additional convenience CAN loads. Certain infotainment system restrictions are implemented. – Deactivation stage 3 – Deactivation stage 6 Reduction of the closed-circuit current is initiated. Bus system wake-up action is reduced. This deactivation stage is activated by way of the diagnosis unit and cannot be initiated independently by the energy management control unit. – Deactivation stage 5 The auxiliary heater is deactivated. – Deactivation stage 4 – Transportation modeDeactivation stages 1 - 3 In stages 1 - 3, loads are deactivated by the control units in the vehicle to prevent further battery discharge. Examples of deactivation stages for onboard power supply control unit 2:Load MMI opening/closing Headlight washing Washer fluid heatingStage 1 Active Inactive InactiveStage 2 Inactive Inactive InactiveStage 3 Inactive Inactive Inactive24 Deactivation stage 4 The fourth stage is the transportation mode, which can be initiated via the diagnosis unit. The transportation mode is designed to greatly reduce battery discharge in the event of lengthy vehicle standing times or longdistance transportation. An adaption channel for activation is provided for this purpose in the energy management control unit J644. In channel 1 "Transportation mode", it is possible to select either 0 = Normal mode or 1 = Transportation mode. Virtually all convenience functions are deactivated in transportation mode to ensure maximum standing time without battery discharge. This is necessary for example during transportation overseas.Transportation mode adaption with diagnosis unitData bus diagnostic interface J533J644Deactivation stage 5 The auxiliary heater is deactivated in this stage.Transportation mode deactivation stage 4Deactivation stage 6 In stage 6, the bus system control units are only wakened with terminal 15 ON and on entering the vehicle. All other sources of bus system wake-up are suppressed. As starting capability is only just retained in deactivation stage 6, it must not be possible for every source to trigger control unit wakeup in order to save power. This also applies to infotainment components and means that it is not possible to use the telephone in stage 6. The reserve battery ensures that emergency and breakdown calls can still be made.SSP287_04025 Control UnitsOperating principleFault memory entry "Deactivation stage 2"Deactivation stage 2 (receiver inactive)Deactivation stage 2J644 "Deactivation stage 2" is transmittedJ502Other control units connected to convenience CANDeactivation stage 2 J533J285Control units connected to MOST bus J525Deactivation stage 2 (radio controlled clock synchronisation inactive) Deactivation stage 2 (amplifier inactive)Deactivation stage 2 SSP287_04326 The energy management control unit J644 transmits the necessary deactivation stage to the data bus as required. After reading in the information, the control units connected to the bus systems deactivate the loads specified for each deactivation stage. For this purpose, the loads to be deactivated in the corresponding deactivation stage are stored in each control unit. In the example the energy management control unit transmits deactivation stage 2 to the convenience CAN. The convenience CAN control units then deactivate the loads/ functions stipulated for deactivation stage 2. These are specified in the software of the corresponding control unit.For example, the tyre pressure monitor control unit J502 deactivates the aerial receiver to save power. The data bus diagnostic interface J533 distributes the information "Deactivation stage 2" to the other bus systems. In turn, the control units connected to the other bus systems then all react by deactivating the loads stipulated for deactivation stage 2. The control unit with display in dash panel insert J285, which is connected to the dash panel insert CAN, deactivates the radio controlled clock receiver to save power or the digital sound package control unit J525 connected to the MOST bus deactivates the audio amplifier.27 Control UnitsGradual closed-circuit current reduction The closed-circuit current reduction stages extend the possible vehicle standing time, as the closed-circuit current decreases with each deactivation stage. There is however no calculation function for standing time extension. If the driver gets into the vehicle, all functions are quickly re-established. Deactivation stage 4 is however a special case. It cannot be initiated by the vehicle alone, use must be made of the diagnosis unit. Deactivation stage 2 is activated immediately if a closed-circuit current 50 mA is determined after a standing time of three hours. Switching on the engine resets all previously active deactivation stages. Connection of a battery charger to a battery connected in the vehicle also deactivates all deactivation stages (refer to Battery charging on Page 36). This does not however apply to deactivation stage 4 – Transportation mode. The priority setting for the deactivation stages is thus 1-2-5-3-6. The designations for the individual stages were established during system development.State of charge (SOC) (%) Normal operationStage 1 Stage 2 Stage 5 Stage 3 Stage 6Closed-circuit current IR (A)Starting capability limitStarting capability limit Time Possible standing time without energy management Standing time extension by way of power consumption reduction SSP287_04428 Systems involved The following systems are involved in load deactivation by way of the closed-circuit manager module in the energy management control unit: – MOST bus Front information display and operating unit control unit J523 CD ROM drive R92 CD changer R41 TV tuner R78 Digital radio R147 Radio module R Navigation system control unit J401 Digital sound package control unit J525 Telephone/telematics control unit J526 Aerials Chip card reader control unit J676 The loads/functions deactivated are indicated in the assisted fault-finding routine under "Vehicle information" as part of the "Function and component selection" section. – Convenience CAN Sunroof electronics control unit J528 Seat adjustment with memory control unit J136 Seat adjustment with memory control unit, front passenger J521 Seat adjustment with memory control unit, rear J522 Climatronic control unit J255 Additional heater control unit J364 Convenience system central control unit J393 Onboard power supply control unit J519 Onboard power supply control unit 2 J520 Door control unit J386 Door control unit J387 Door control unit J388 Door control unit J389 Entry and start authorisation control unit J518 Tyre pressure monitor control unit J502 Control unit with display in dash panel insert J285 Driver identification control unit J589Alternator Use is made in the Audi A8 ´03 of a watercooled 190 A alternator from Hitachi. The rated currents of the alternator incorporated into the engine cooling circuit are as follows: – At alternator speed n = 1800 rpm (corresponding to engine idling) In = 130 A – At alternator speed n = 6000 rpm In = 190 A Further information on the water-cooled alternator can be found in SSP 268 – "The 6.0 l W12 engine in the Audi A8 - Part 2".SSP287_122 29 Control UnitsDynamic management The function of the dynamic management system is to distribute the power generated to the individual systems as required and to provide the battery with sufficient charging current. It is active when the engine is running. Main tasks: – – – – – – Battery voltage regulation Load shedding Regulation of heavy-duty heating systems Idling speed increase Alternator activation Alternator control dynamics The dynamic energy manager monitors electrical system capacity utilisation by measuring electrical system voltage, battery current and alternator capacity utilisation. To ensure a stable power supply, the power available in the electrical system is distributed as required. Three control stages are available for this purpose.Control stages 1 Continuous power regulationHeating system control conditions Electrical system overload due to utilisation of full alternator capacity accompanied by drop in battery charging voltage to below specified values Only in the event of a fault (or briefly, 10 s, with no fault memory entry): – Permanent power overload ( 10 s), electrical system cannot be stabilised by way of simple regulation as part of continuous heating system control, battery charged (starting jeopardised) – Alternator fault (fault memory entry 02252) – Alternator high-temperature regulation (fault memory entry 02253) – Load shedding by engine control unit (e.g. high alternator load is reduced on speed dip); only possible for 10 s - no fault storage Only in the event of a fault (or briefly, 15 s, with no fault memory entry): – Severe undervoltage in electrical system ( 11.5 V for 1.5 s or 10.8 V for 0.5 s) Note: Full emergency shutdown on starting is also set up to 15 s after starting depending on engine control unit release. There is no fault memory entry in this case as deactivation is only for a very restricted period and is not registered by the driver.2aPartial emergency shutdown2bFull emergency shutdown30 Control stages 1 Continuous power regulation 2a Partial emergency shutdown Minimum power 0W 2b Full emergency shutdown Minimum power 0WHeating system Heated rear window Heated windscreen Seat heatingMaximum power approx. 320 WMinimum power 0W1000 W250 W250 W0WFront: 2 x 100 W Rear: 2 x 80 W 2 x 250 WFront: 2 x 25 W Rear: 2 x 20 W 2 x 50 WFront: 2 x 25 W Rear: 2 x 20 W 2 x 50 W0WRear additional heater Steering wheel heating Jet and fluid hose heating Mirror heating0Wapprox. 100 WNo restriction No restriction0W0W20 to 100 W0W0W2 x 30 WNo restriction0W0W31 Control UnitsBattery voltage regulation The energy management control unit J644 informs the alternator of the specified alternator voltage required via a data wire (bit-synchronous interface). This voltage is then set by the alternator. The battery manager (function module 1) determines the specified value from battery temperature and battery charge. The specified value established is then transferred in the control unit to the dynamic management (function module 3), which relays the value to the alternator. The assisted fault-finding routine contains measured value blocks for checking the specified alternator voltage and communication via the data wire. The specified alternator voltage can be altered for diagnosis purposes as part of final control diagnosis.Function module 3 Function module 1J644Specified alternator voltageAlternator SSP287_020Load shedding The energy management control unit can reduce the engine load (e.g. on accelerating) if so requested by the engine control unit. If the engine control unit requests load shedding, the energy management system reduces heavy-duty loads in the first stage and alternator voltage in the second stage to lower the level of alternator power input. For this purpose, the energy management control unit transmits a request via the convenience CAN to the Climatronic control unit J255, which regulates various heating systems, such as heated windscreen, seat heating, heated rear window and additional heater.J623Load shedding request J533Load shedding feedback J644SSP287_06232 Regulation of heavy-duty heating systems By way of the Climatronic control unit J255, the energy management control unit J644 infinitely regulates the heat output of – – – – Windscreen Rear window Rear additional heater and seat heatingJ644In doing so, it determines the maximum heat output which can be provided.J255Heat outputSSP287_021Heated windscreen (LIN bus) Rear additional heater (LIN bus) Seat heating (discrete wire) Heated rear windowIdling speed increase To ensure optimum electrical system supply and battery charging, the energy management system can request the engine control unit to increase the idling speed in stages (7 % and 12 %).Alternator activation (start load response) On starting the engine, the alternator power input is minimised in order to optimise the starting process.J623 Engine speed feedbackJ533Alternator control dynamics (drive load response) When the heated rear window is switched on, the alternator voltage is not increased immediately, but rather adjusted within 3, 6 or 9 s as a function of engine speed and temperature. This continuous, infinitely variable regulation of the alternator torque results in uniform engine loading.Idling speed increase requestBSI J644 Alternator SSP287_11533 Control UnitsFault memory entry Activation of a deactivation stage by the energy management control unit restricts the functioning of certain systems. A fault memory entry is made in the energy management control unit, e.g.: – Alternator mechanical fault – Alternator electrical fault – Alternator high-temperature regulationVehicle self-diagnosis 02 - Interrogating fault memory 1 fault detected 02275 Closed circuit stage 4 000 61 - Battery control 4E0915181 ENERGY MANAGER H02 0070 Dealership number 0The accompanying data for the corresponding fault memory entries contains additional information, such as mileage or date at/on which a fault was stored.MeasurementVehicle selfdiagnosisJumpPrintHelpSSP287_022Measured value blocks Assisted fault-finding permits call-up of measured values, such as – – – – – – – – – – Specified alternator voltage Battery voltage Busbar temperature Battery temperature State of charge (SOC) Communication with alternator Mean closed-circuit current value Emergency shutdown Closed-circuit deactivation Internal battery resistance, charge lossAssisted fault-finding Functional test J644 - Display measured value blocks Audi V05.02 18/06/2002 Audi A8 2003 2003 (3) Saloon BFM 4.2l Motronic / 246 kWMeasured value block 1 14.4 V Specified alternator voltage 13.75 V Battery voltage 54.84 % DF signal 3s Load response timeFunctional descriptionin the measured value blocks.Measurement Jump Print HelpSSP287_02334 Final control diagnosis Final control diagnosis can be used to alter the specified alternator voltage for diagnosis purposes. Specified alternator voltages of 15 V and 13.5 V can be set. It must then be possible to measure the value correspondingly set as alternator specification at the alternator terminal.Assisted fault-finding Functional test Audi V05.02 18/06/2002 Audi A8 2003 2003 (3) Saloon BFM 4.2l Motronic / 246 kWSelectionThis test is intended for implementation of control element tests for the energy management control unit. The following control element tests can be performed. 1. Specified alternator voltage 15 V 2. Specified alternator voltage 13.5 V 3. End of program-1--2--3-MeasurementVehicle selfdiagnosisJumpPrintHelpSSP287_054Service work Battery diagnosis In the Audi A8 ´03, the battery is tested by the energy management control unit. Checking the battery with a load test is no longer necessary. Assisted fault-finding permits callup of the "Function and component selection" menu, from which the battery test is started. The control unit determines the state of charge (SOC), internal battery resistance and energy flow and uses these to calculate whether the battery is OK, charged or in need of replacement.35 Control UnitsBattery charging The battery charger must be connected with the external starting tap at the battery positive terminal and the negative terminal at the external starting pin. The battery should always be re-charged in the vehicle. This enables the energy management control unit to incorporate the charging current into the battery value calculations. When working on the vehicle with terminal 15 ON and engine off, a battery charger should always be connected up, as otherwise functions may be deactivated on account of excessive current consumption. The chargers used must be capable of supplying a stabilised current of at least 30 A.SSP287_068 External starting pinRapid charging of the battery in the vehicle is not permitted.External starting tapHeed the battery and equipment manufacturers' specifications when charging the battery. Also pay attention to the information on the battery itself.Battery replacement On battery replacement, the new battery must be adapted by way of the diagnosis tester. The menu item "Battery manager encoding" is provided in the assisted faultfinding routine in the list of systems with selfdiagnosis capability in the battery manager. The battery serial number has to be entered for encoding. This is marked on the battery.External starting For external starting, the starter cable earth is to be connected to the external starting pin and the positive cable to the external starting tap.36 37 Control UnitsControl unit with display in dash panel insert J285SSP287_077Instrument illumination controlsAuto-Check systemReset button for trip recorderThe dash panel insert in the Audi A8 ´03 has been modified with respect to the predecessor model. Certain functions have been changed. New features: – No gateway – Immobilizer function no longer in dash panel insert – Modified vehicle-speed signal input – No immobilizer warning lamp – Modified fuel gauge G1 – Modified coolant-temperature gaugeImmobilizer The immobilizer function has been incorporated into the entry and start authorisation control unit J518. Adaption to the immobilizer is therefore no longer necessary on replacing dash panel insert.Gateway On account of additional new functions, the data bus diagnostic interface (gateway) J533 is now designed as a separate, external control unit.There is thus no longer any connection between an immobilizer fault and the dash panel insert.38 Immobilizer warning lamp The immobilizer warning lamp has been discontinued. In the event of a key identification fault, a signal is transmitted by the entry and start authorisation control unit J518. "Safe" then appears in the mileage display. This display is also used to show the number of keys to be matched and the number already matched on vehicle key adaption.Fuel gauge G1 The input signal is now provided by four fuel gauge senders in the fuel tank, all of which are evaluated separately. Fuel gauge sender operation is described in SSP 282 – Audi A8 ´03 Technical Features. Coolant-temperature gauge G21 The input signal for the coolant-temperature gauge is no longer supplied by the coolanttemperature sender G62, but rather it is transmitted by the engine control unit to the dash panel insert.Vehicle-speed signal The vehicle-speed signal is now supplied by the ABS with EDL control unit J104 via the drive system CAN.The wheel circumference must be available to the dash panel insert to ensure correct evaluation of the vehiclespeed signal. The permissible wheel circumferences are included in the encoding and selected by way of assisted fault-finding.39 Control UnitsBlock diagram30 15G34G35G266 J489 J540 F34J285 J49 J171PJ533 F1 F77 F66 G17M MG393 G237 G23G169GG6SSP287_036Key F1 F34 F66 F77 Oil pressure switch Brake fluid level warning contact Coolant shortage indicator switch Windscreen washer fluid warning contact Fuel gauge sender Fuel pump (pre-supply pump) Ambient temperature sensor Fuel pump Brake lining/pad wear sender, front left Brake lining/pad wear sender, front right Fuel gauge sender 2 Fuel gauge sender 3 Oil level/oil temperature sender Fuel gauge sender 4 J17 J49 J285 J489 J533 J540 Fuel pump relay Electric fuel pump 2 relay Control unit with display in dash panel insert Radio controlled clock receiver Data bus diagnostic interface Electric park and handbrake control unitG G6 G17 G23 G34 G35 G169 G237 G266 G393Additional signal 1 Terminal 58s40 Convenience system central control unit J393Use is made in the Audi A8 ´03 of the familiar convenience system central control unit J393 from the Audi A2 and Audi A4. The tasks and functions have been adapted accordingly to suit the requirements of the Audi A8. The control unit is connected to the convenience CAN.SSP287_048Fitting location The convenience system central control unit is installed at the rear right of the luggage compartment above the battery.Master functions The master functions of the convenience system central control unit are as follows: – LIN master for boot lid control unit J605 and anti-theft/tilt system control unit J529 – Central locking master – Flashing signal master – Anti-theft alarm masterJ393 SSP287_069Convenience CANLIN master As LIN master for the LIN slaves (boot lid control unit J605 and anti-theft/tilt system control unit J529), the convenience system central control unit is designed to provide all the information required by the LIN slaves to execute their functions on the LIN bus and to call up the necessary data for function implementation from the LIN slaves.LIN busJ605J529 SSP287_070 41 Control UnitsCentral locking masterJ393As central locking master, the task of the convenience system control unit is to control the central locking function. By way of the convenience CAN, the control unit reads in the door opening authorisation from the entry and start authorisation control unit J518. The convenience system central control unit then transmits the command for opening/closing the doors to the door control units via the convenience CAN.Door opening authorisation J386 J387Central locking control is described in SSP 288 - Audi A8 ´03 Distributed Functions.J388J389Door opening authorisationJ518 SSP287_071Flashing signal master As flashing signal master, the convenience system central control unit evaluates the incoming flashing mode requests and passes the corresponding flashing mode to the convenience CAN in line with the internal priority list. Flashing modes include turn signals, motorway signalling, anti-theft alarm flashing and central locking system flashing. As several flashing requests may be received simultaneously, priorities must be assigned to flashing modes. The control units involved in the "flashing" function read in the flashing mode from the convenience CAN and actuate their outputs accordingly.Control of the flashing signal system is also described in SSP 288 - Audi A8 ´03 Distributed Functions.42 DiebstahlwarnanlagenmasterF2 F3Convenience CAN F266 J386 J387 F218J519J393H12J388 J528J389 J529F10F11SSP287_075As anti-theft alarm master, the control unit evaluates the corresponding vehicle monitoring information and actuates the antitheft output media as required. All components are simultaneously primed/ deactivated. When the anti-theft alarm system is primed, all door contacts, the bonnet contact, the boot lid contact, the passenger compartment and vehicle tilt are monitored.Door contact switch – driver side Door contact switch – front passenger side F10 Rear left door contact switch F11 Rear right door contact switch F218 Boot lid central locking switch F266 Bonnet contact switch H12 J386 J387 J388 J389 J393 Alarm hornF2 F3Door control unit, driver side Door control unit, front passenger side Door control unit, rear left Door control unit, rear right Convenience system central control unit J519 Onboard power supply control unit J528 Sunroof electronics control unit J529 Anti-theft/tilt system control unit43 Control UnitsActuation Rear left and right footwell lights The convenience system central control unit actuates the rear footwell lights. The actuation time and brightness value are specified by the sunroof electronics control unit J528.Rear roller blind The rear roller blind can be operated with the rear roller blind switch or via the rear roof console. The rear roller blind switch is read in by the Climatronic control unit and transmitted to the convenience CAN. The rear roof module operating unit information is read in by the sunroof electronics control unit and transmitted to the convenience CAN. The convenience system central control unit reads in the rear roller blind actuation information from the convenience CAN and actuates the rear roller blind motor accordingly. E149 Rear roller blind switch E467 Rear roof console J255 Climatronic control unit J393 Convenience system central control unit J528 Sunroof electronics control unit V91 Rear roller blind motorConvenience CANJ255E149J528E467J393V91SSP287_076Luggage compartment lights Opening the boot lid causes the convenience system central control unit to actuate the luggage compartment light W3, the left luggage compartment light W18 and the right luggage compartment light W35. The lighting is switched off with terminal 15 ON when the boot lid is closed or the vehicle speed exceeds 2 km/h. With terminal 15 OFF, the lighting is again switched off by the control unit on closing the boot lid or on completion of the maximum operating time of 10 minutes. Following timebased deactivation, the lighting can only be re-activated if the driver's or front passenger's door and the boot lid are opened or terminal 15 is activated.44 Heated rear window Z1 The convenience system central control unit actuates the heated rear window via the heated rear window relay J9. The relay actuation information is supplied to the convenience system central control unit by the Climatronic control unit.System outlineThe convenience system central control unit J393 receives the following input signals: – – – – Boot lid soft touch Lock cylinder CLOSED Brake light switch Brake light signal from ABS with EDL control unit J104 – – – – Crash input Boot lid contact Tank filler flap detection Boot lid power latching system feedbackThe convenience system central control unit J393 actuates the following loads: – – – – – – – – Rear left and right footwell lights Luggage compartment lights Rear roller blind motor V91 Fuel tank filler flap central locking actuator F219 Boot lid control unit J605 Boot lid power latching system Boot lid release motor V139 Left and right turn signal indicator (LED) – – – – – – – – – High-level brake light (LED) Left and right tail light (LED) Left and right brake light (LED) Rear left and rear right brake light (LED) Left and right reversing light Left and right rear fog light Number plate light Heated rear window Z1 Alarm horn H1245 Control UnitsBlock diagram30 15J657MJ529J605 E406 L76 W18 W3 W35J393J690J692J693J691M9 M4 M6M9 M4 M16 L46L47 M17 M2 M10M8 M2 M10Key C18 Windscreen aerial suppression filter J690 Left tail light control unit J691 Right tail light control unit J692 Tail light control unit for lights on left in boot lid J693 Tail light control unit for lights on right in boot lid L46 L47 L76 M2 M4 M6 M8 M9 M10 M16 M17 M25 Rear fog light bulb, left Rear fog light bulb, right Button illumination Tail light bulb, right Tail light bulb, left Turn signal bulb, rear left Turn signal bulb, rear right Brake light bulb, left Brake light bulb, right Reversing light bulb, left Reversing light bulb, right High-level brake light bulbE406 Boot lid close button in luggage compartment F124 Contact switch in lock cylinder for boot lid anti-theft alarm system/central locking system F218 Boot lid central locking switch F248 Release button for boot lid lock cylinder H12 Alarm hornJ9 Heated rear window relay J393 Convenience system central control unit J529 Anti-theft/tilt system control unit J605 Boot lid control unit J657 Power latching control unit46 MF218V53F124F248H12J9C18Z11M M23456XM25W45W46V155V91SSP287_035V53 Central locking motor, boot lid V91 Rear roller blind motor V155 Tank filler flap locking motor W3 W18 W35 W45 W46 X Z1 Luggage compartment light Left luggage compartment light Right luggage compartment light Rear left footwell light Rear right footwell light Number plate lightAdditional signals 1 2 3 4 Convenience CAN High Convenience CAN Low Brake light switch F ESP brake signal from ABS with EDL control unit J104 Crash signal from airbag control unit J234 "Doors OPEN" signal to adaptive suspension control unit J1975 Heated rear window 647 Control UnitsTail light actuationBrake/ tail light on boot lidBrake/ tail light on side panel Turn signal indicatorRear fog light Reversing lightReflectorSSP287_030Some of the rear light units are of diode type (turn signal indicators, tail lights and brake lights). Each has an integrated microprocessor for actuation. The diodes are arranged in a matrix. If one diode fails, the other diodes for this function continue to light. The microprocessor governs whether the red LEDs operate as tail light (approx. 10 % PWM signal) or as brake light (approx. 97 % PWM signal).This simplifies the wiring and various emergency functions can be implemented. Total failure or malfunctioning of the internal transistor is detected by the microprocessor, which transmits a fault message to the convenience system central control unit J393. The turn signal LEDs are actuated in the same manner as the tail light LEDs, however there is no PWM control.Tail/ brake lightTurn signal indicator1 2 3Tail light signal Brake light signal Bidirectional wire from convenience system central control unit Indicator signalSSP287_1171 2 3 4448 Boot lid control unit J605The boot lid control unit provides extra convenience when opening and closing the boot lid. The electromechanical drive system with a motor and magnetic clutch is controlled electronically and responds to requests from the convenience system central control unit. The current position status and the switching status of the boot lid closing button are signalled to the convenience system central control unit. The boot lid control sequence is measured by way of an integrated potentiometer. This permits – Detection of the end positions – Detection of excess force and thus implementation of obstruction safeguard through evaluation of the rate of changeOperation Opening/closing involves engagement of the magnetic clutch and starting of the motor. During movement, the current position of the boot lid is detected via the potentiometer and compared to the previous value. If there are no problems, the boot lid is moved into the desired end position, where the drive is switched off. In the event of an obstruction or opposing force during opening/closing, movement is halted by disengaging the magnetic clutch and the motor comes to a stop. If it was being closed, the boot lid is opened again (obstruction safeguard).Hinge mechanismDrive shaftControl electronics PotentiometerElectrical connectionMagnetic clutch Electric motor SSP287_080 Gear mechanism 49 Control UnitsThe boot lid control unit receives the input signal from the boot lid close button in luggage compartment E406.For safety reasons, the boot lid cannot be closed from the operating points in the remote control key, in the driver's door or on the outside of the boot lid.SSP287_08130Block diagram E406 Boot lid close button in luggage compartment J393 Convenience system central control unit J529 Anti-theft/tilt system control unit J605 Boot lid control unit L76 Button illuminationJ529J605 E406 L76J393SSP287_082Fitting location The boot lid control unit is located behind the side panel at the top right and is flanged to the right boot lid hinge.SSP287_083 50 Anti-theft/tilt system control unit J529As in the Audi A4 ´01, use is made of a tilt sensor to prevent unauthorised tow-starting. The tilt sensor in the Audi A8 ´03 is an independent control unit. The anti-theft/tilt system control unit is connected to the convenience system central control unit J393 via a LIN bus link.SSP287_047Design The internal design and mode of operation have been modified as compared to the tilt sensor in the Audi A4 ´01. The control unit contains the sensor element, the microcontroller and a LIN transceiver. The sensor consists of a moving earth element suspended between two capacitor plates by means of springs. The capacitor plate connections are routed into the microcontroller.SpringsCapacitor platesEarth elementOperation A change in the horizontal position of the control unit moves the earth element between the capacitor plates within the spring travel range. A voltage is applied to the capacitor plates. Movement of the earth element produces a change in capacitance between the plates. This voltage signal is recognised as a change in vehicle tilt by the microcontroller. The measuring range of the sensor is ± 25°. The change in capacitance is evaluated with an accuracy of 0.1°.SSP287_078 MicrocontrollerSSP287_07951 Control UnitsBlock diagram J393 Convenience system central control unit J529 Anti-theft/tilt system control unit J605 Boot lid control unit30J529J605J393SSP287_074Fitting location The anti-theft/tilt system control unit is located on the right beneath the rear seat bench.SSP287_029Diagnosis The absolute tilt angles can be displayed in the measured value blocks. In addition, with the anti-theft alarm primed, it is also possible to read out the change in angle with respect to the angle on priming the anti-theft alarm. Diagnosis for the anti-theft/tilt system control unit is performed by way of the central convenience electronics.52 Onboard power supply control unit J519Functions The onboard power supply control unit was first used in the Audi A4 ´01. It is also fitted with appropriately modified functions and actuation processes in the Audi A8 ´03. The onboard power supply control unit is designed to read in various switches and actuate certain outputs.Master functions The master functions of the onboard power supply control unit are as follows: – LIN master for wiper motor control unit J400 (refer to wiper motor for functions) – Light master As light master, the task of the onboard power supply control unit is to provide all control units concerned with the required type of lighting, e.g. side lights, via the data transfer systems to enable the control units to actuate the appropriate control elements. In addition, it monitors operation of the front external vehicle lights. This takes the form of cold and warm lamp monitoring. Exterior lighting control is described in SSP 288 – Audi A8 ´03 - Distributed Functions. Substitute master function The onboard power supply control unit assumes the substitute master function for the convenience system central control unit J393. In other words, if the convenience system control unit is disconnected from the CAN bus or defective, the onboard power supply control unit transmits the flashing signal information to the CAN bus (refer to SSP 288 – Audi A8 ´03 - Distributed Functions).SSP287_045J519J400SSP287_03253 Control UnitsBlock diagram75X 30 15E266 L117 K136 E149 L76 1EL76K145E3K6E256 L761234567J519 1 8 9J667MJ668MJ431L13 M51 M30M1 M5 V48L14 M52 M32M3 M7 V49Key E1 E3 E7 E18 E26 E149 E256 E266 E462 F266 G357 G358 H2 H7 J4 J400 J431 J519 J667 J668 Light switch Hazard warning light switch Fog light switch Rear fog light switch Glove box light switch Rear roller blind switch TCS/ESP button Parking aid button Open/close button for front display Bonnet contact switch Steering column adjustment sender, vertical Steering column adjustment sender, axial High-tone horn Low-tone horn Dual-tone horn relay Wiper