TECHNICAL DOCUMENTATION

SSP 040 Automatic gearbox 001 – Fabia

PDFEN46 pages4 MB
SSP 040 Automatic gearbox 001 – Fabia - PDF cover

This PDF is currently unavailable.

Read document text
SP40_54… and now also with an automatic gearbox!Automatic gearboxes are increasingly becoming an everyday element of enhanced comfort in vehicles. Modern functional details in terms of production, hydraulics and electronics make reliable "automatic" driving possible in a car fitted with an automatic gearbox. An automatic gearbox takes over the task of engaging the clutch when starting off, selecting the right gear ratios and shifting gears on its own. Various shift programmes ensure that the engine is always operating in the range which offers the best fuel consumption. The 4-speed automatic gearbox 001 which is presented in this booklet, is a Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability contribution to enhancing comfort in vehicle and relieving the strain of the with respect tothe the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� driver. The driver is no longer required to provide the physical effort needed for engaging and disengaging the clutch and shifting gears. This avoids stress and enhances road safety.Note: You can find the fundamental interactions and operating descriptions in the Self Study Programmes SSP 20 "Automatic Gearbox" (Fundamentals) and SSP 21 "Automatic Gearbox 01M" (Information on the Technology).2GB ContentsIntroduction Operation Overview of System Sensors Actuators Function Diagram Self-Diagnosis Mechanical/Hydraulic System Power Flow Test Your KnowledgeProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�4 8 12 14 17 21 24 26 40 46Servicexxxxxxxxxxxxxxxx FABIAServicexxxxxxxxxxxxxxxx FABIAService Service Service Service Servicexxxxxxxxxxxxxxxx FABIA xxxxxxxxxxxxxxxx FABIA xxxxxxxxxxxxxxxx FABIA xxxxxxxxxxxxxxxx FABIA xxxxxxxxxxxxxxxx FABIAS e r v i c eXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXYou will find notes on inspection and maintenance, setting and repair instructions in the Workshop Manual.GB3 IntroductionThe automatic gearbox 001is an electronically controlled 4-speed gearbox. It consists of the following components – – – – – torque converter with lockup clutch ATF pump (Automatic Transmission Fluid = special oil for automatic gearboxes) ATF cooler planetary gear oil pressure-operated multi-plate clutches, multi-plate brake and band brake (which are assigned to the individual elements of the planetary gear for selecting gears) freewheels for optimising power engagements final drive and electronic-hydraulic gearbox control. A gearbox control unit detects the incoming sensor signals, analyses these and automatically selects a matching shift programme, depending on the style of driving. The Dynamic Shift Programme (DSP) integrated in the control unit, makes it possible to achieve an "economic" or "sporty" style of driving. The gears are shifted automatically. Slip losses occur in the torque converter. The torque converter lockup clutch makes it possible to establish a direct mechanical power transmission for the engine to the gearbox (improves the transmission efficiency). This in turn improves fuel consumption and reduces exhaust emission levels.– – –Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP40_014GB Schematic design of automatic gearbox 001Freewheel Torque converter with lockup clutch (closed) Brake ATF pump Planetary gear ClutchInput gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Output gearDrive pinion (intermediate gear stage) Park lock gear Final driveSP40_03GB5 IntroductionOverview of electrical/electronic components and their fitting locations(taking the example of 1.4-ltr./55 kW engine)4LV control unit J537 (engine control unit)Angle sensor 1 for throttle valve drive G187 in throttle valve control unit J338Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Automatic gearbox control unit J217Gearbox6GB Selector lever position display Y6Selector lever lock solenoid N110Diagnostic connectionStarter lockout relay J207Accelerator pedal position senders G79 and G185 with kickdown switch F8Brake light switch FSP40_04Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB7 OperationSelector lever positions/functionsIt is only possible to start the engine in positions N or P. The position of the selector lever is shown in the selector lever position display in the instrument cluster. The meaning of the different positions is as follows: P Park lock and also start position; gearbox output is blocked mechanically; the ignition key can be withdrawn Reverse gear; engage only when car stationary or engine idling; the reversing lights come on if the ignition is switched on Neutral position or idling; is also a start position; Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted no torque transmitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�RNDDrive - automatic driving position; forward driving range all 4 gears shift automatically Forward driving range gears 1 to 3 shift automatically; 4th gear is not used Forward driving range gears 1 and 2 shift automatically; gears 3 and 4 are not used Forward driving range only 1st gear is usedSP40_023218GB Gear selection in particular situations If particular driving or traffic circumstances necessitate frequently changing gears in rapid succession, or when negotiating a long or steep downhill or uphill section, or if particular road conditions exist (such as icy road surface or snow), it is recommended to engage one of the stages between 1 and 3. This makes it possible, for example, on a downhill section to exploit the maximum engine braking effect and to thus minimise the wear-and-tear on the brakes. Emergency mode If the control unit fails, it is still possible to operate the selector lever and engage – – 3rd gear and 1st gear, as well as reverse gear.Selector lever Lock buttonThe selector lever lock prevents a driving range being engaged unintentionally. The selector lever is locked when it is in position P or N - even if the ignition is switched on. The lock can be disengaged only by simultaneously depressing the footbrake and pressing the lock button on the selector lever. Only then is it possible to move the selector lever into a driving position.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP40_02Note: The information provided in SSP 21 in respect of – push-starting and – tow-starting the car also apply by analogy to this automatic gearbox. It is not possible to start the engine by tow-starting or push-starting the car because of the lack of ATF pressure. If the car is towed in, the towing speed must not be higher than 50 km/h and the towing distance must not be more than 50 km.GB9 OperationDynamic Shift Programme In the early days of electronic transmission controls of automatic gearboxes, only fixed shift characteristic curves were programmed. As gearbox control systems underwent further development, the motorist was then provided with the option of actively switching between the two characteristic curves of "Economy" (ECO) and "Sporty" (SPORT). The driver switched over between these options by operating a separate switch on the selector lever. In the case of automatic gearbox 001 it is the automatic gearbox control unit J217 which performs this task of switching over as a function of the – – – –ECO SPORTAccelerator pedal positionEngine speed previously: two shift characteristic curvesSP40_08particular position of the selector lever, position of the accelerator pedal, the rate which thefor accelerator pedal is in part or in whole, is not permitted Protected byat copyright. Copying private or commercial purposes, unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability operated, with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� driving situation.If the driver presses rapidly on the accelerator pedal because he wishes to accelerate sharply, the control unit switches into a "sporty" shift curve. If the driver does not alter the position of accelerator pedal, the control unit moves into an "economy" shift curve. Uphill and downhill sections of the road are detected and processed.Automatic gearbox control unitSP40_56The incoming information is analysed, the shift decisions which are output are verified, and new shift decisions are computed in a continuous cycle which lasts about 20 ms.The basis of this analysis is formed by a Dynamic Shift Programme (DSP) with integrated adaptive shift characteristic curves.10GB Adaptive shift characteristic curvesNew!The shift decision (based on the so-called fuzzy logic) is taken by the control unit on the basis of a shift characteristic curve map - with the so-called adaptive shift characteristic curves, in other words there are not only two fixed characteristic curves available, but an array of many shift characteristic curves integrated in a map (ill. opposite). After analysing the signals supplied by the sensors, the control unit selects the correct gear and operates the necessary actuators and shift elements (multi-disc clutches, multi-disc brake and/or band brake). This makes it possible to react more sensitively to the individual requests of the driver and to achieve "softer" gearshifts.Accelerator pedal position123Engine speedShift characteristic curve map (with an array of shift curves)SP40_09Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Examples of gearshifts with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The control unit detects from the rate at which the accelerator pedal is operated, whether the driver wishes an "economy" or "sporty" style of driving. The control unit therefore selects the characteristic curve from the map which corresponds to this driver input - a slow rate of operation of the accelerator pedal means "economy" driving (example 1), while a faster rate of operation indicates the desire for a "sporty" style of driving (example 3).Example 1 (more ECO) The accelerator pedal is moved at a slow rate. Example 2 The accelerator pedal is moved at a moderate rate. Example 3 (more SPORT) The accelerator pedal is moved at a fast rate.Note: You can read more on fuzzy logic in SSP 20.GB11 System Overviewtaken the example of the 1.4-ltr./55 kW engineSensorsAngle sender 1 for throttle valve drive G1874LV control unit J537 (engine control unit)Accelerator pedal position sender G79 and G185Automatic gearbox control unit J217Gearbox speed sender G38Vehicle speed sender G68ATF temperature sender Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted G93 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Multifunction switch F125Brake light switch F Diagnostic connection ABS control unit J10412GB ActuatorsSolenoid valves 1 … 6 N88 … N93Control valve housingSelector lever lock solenoid N110Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Vehicle electrical system control unit J519Starter lockout relay J207Additional signalsPAUFN EIN AUSCruise control system4LV control unit J537 (engine control unit)Air conditioningSP40_10GB13 SensorsAccelerator pedal position sender G79 and G185This sender is located at the accelerator pedal. It signals the position of the accelerator pedal and the rate at which the accelerator pedal is operated, to the engine control unit. The function of the kickdown switch is integrated. The signals between the engine control unit and the gearbox control unit are transmitted over the drive databus. The message "Rapid depressing down to full throttle position" causes the gearbox to shift down into a lower gear matching the driving situation (in certain circumstances several gear stages) and also in the air conditioning being switched off for a short time so that full or commercial purposes, in part or in whole, is not permitted Protected by copyright. Copying for private unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability engine torque is available for accelerating. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP40_16Angle sender for throttle valve drive G187The positioning motor for the throttle valve is operated by the engine control unit and alters the position of the throttle valve. The angle sender for the throttle valve drive G187 signals the current throttle valve position to the engine control unit. This signal is passed onto the gearbox control unit. The signals are transmitted over the drive databus. The signal is used for calculating the moment at which the gearshift is performed.Positioning motorSP40_11Angle sender for throttle valve drive14GB Vehicle speed sender G68The sender for the vehicle speed is an inductive sensor and is installed at the gearbox housing. It detects the speed at which the vehicle is driven by means of the output gear. The signal is required for selecting gears.SP40_13ATF temperature sender G93The sender is located in the control valve body. It is designed as an NTC resistor. The control unit calculates the temperature of the ATF from the variation in the voltage which the resistor produces. The temperature is required for – controlling the pressure of the ATF – controlling the torque converter lockup clutch (it is not closed if the ATF is cold) – selecting the gears (the gearbox does not shift into 4th if the temperature is below –20 ˚C.SP40_14Gearbox speed sender G38The sender for the gearbox speed is an inductive sensor and is installed in the gearbox housing. It detects the clutch K3. Multi-disc clutch K3 is connected to the turbine shaft and rotates at its speed.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability rotational speed of the multi-disc with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The signal is required for – calculating the engine torque – determining the moment of the gearshift in line with engine load, and – controlling the torque converter lockup clutch.SP40_12If no signal is received, it is not possible – to shift into 4th gear – to vary the ignition timing point – to reduce the engine torque (harder gearshifts).GB15 SensorsMultifunction switch F125This switch is located at the gearbox housing and is operated by the selector lever using the selector lever cable. The multifunction switch detects the position of the selector lever P, R, D, 3, 2 or 1 and signals this to the control unit of the automatic gearbox. The control of the gearbox is based on the position signal.SP40_06The functions of – – controlling the starter lockout relay, and switching on the reversing lightsare initiated by the multifunction switch. If the multifunction switch fails, it is then no longer possible to start the car and the relay for the reversing lights is no longer operated. If the multifunction switch fails when driving, the control unit for the automatic gearbox moves into the emergency running mode.Brake light switch FIt is located at the pedal assembly. The gearbox control unit is supplied with the "brake operated" signal through this switch. The following functions are activated: – The selector lever lock is released when the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability brake is operated.with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP40_15–The torque converter lockup clutch is opened when the car is braked.16GB ActuatorsSelector lever lock solenoid N110The solenoid is located at the shift mechanism. Together with the mechanical selector lever lock, it acts as a technical safeguard to prevent incorrect operations of the automatic gearbox. The selector lever is locked in the position "P" and "N". The solenoid is connected to the ignition and, by means of an electro-mechanical mechanism, prevents a Drive position being engaged inadvertently with the selector lever. The lock is cancelled only when the footbrake pedal is depressed and it is then possible to move the selector lever into the chosen range - this usually being "D" - while at the same time holding the Unlock button pressed.SP40_05Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Starter lockout relay J207This relay is located on the relay carrier above the vehicle electrical system control unit. It prevents the engine being started when a Drive position is engaged.SP40_17GB17 ActuatorsSolenoid valves N88 to N93The control valve body is the electro-hydraulic shift unit of the automatic gearbox. All the valves are housed in the control valve body on the underside of the gearbox, and are operated by the control unit for the automatic gearbox. A distinction is made between shift valves with a yes/no characteristic (N88, N89, N90, N92) and modulation valves (N91 and N93).N92N89 N91N88Note: The colours of the cables for the individual valves differ: N88 green N89 yellow N90 grey N91 blue N92 black N93 redN90N93SP40_18The interaction of the shift valves (they each open or close an oil passage) results in individual gears being shifted, the freewheel and/or the torque converter lockup clutch being operated.The oil pressure is set by means of the two modulation valves N91 and N93. It is possible to achieve a stepless control of the pressure. Valve N91 operates the lockup clutch. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted N93 controls the ATF pressure unless authorised by ŠKODA AUTO A. S. ŠValve KODA AUTO A. S. does not guarantee or accept any liability for withcontrol respect to the correctness of information in this document. by ŠKODA AUTO A. S.and � The valves activated by the unit, allow operating theCopyright multi-disc clutches the the oil pressure to flow along passages to the brakes in line with the position of the corresponding clutches or brakes in such a accelerator pedal (angle sender G187 in the way that the individual gear stages are shifted throttle valve control unit). by holding individual shafts or gearwheels tight, or releasing them. The freewheels act as supports and permit only one direction of rotation.18GB Additional signals to …… the cruise control system It is possible to drive with the cruise control system (CCS) at a speed of more than 30 km/h if the selector lever is in position "D" and "3".PThe control unit for the automatic gearbox sends a signal over the Drive databus (CAN/A) to tell the engine control unit when the gearbox is shifted into positions P, R, N, 2 and 1. When this is the case, the cruise control system (CCS) switches off.S AUFN EIN AUSP40_19Engine control unit J...… the air conditioning system If the accelerator pedal is depressed sharply, the sender for the accelerator pedal position G79 generates the "kickdown signal".CAN-H/AAccelerator pedal position sender G79The engine control unit analyses this signal and decides which measures are necessary for assuring the torque required: – shifting down into a lower gearCAN-L/AVehicle electrical system control unit J519 (Gateway)CAN-H/K26–switching theauthorised compressor aA.short time unless by ŠKODA for AUTO S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� into the "AC OFF" operating position. If this is done, the flow volume and also the power consumption of the air conditioning are reduced to a minimum.22 18Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedCAN-L/KACand, if this alone is not sufficient,SP40_20AC control unit J301Control valve for AC compressor N280GB19 Actuators… the engine control unit The automatic gearbox control unit is linked over the CAN databus to the engine control unit. Information flows over this link if, for example, it is necessary to reduce the engine torque during a gearshift by controlling the ignition timing point. If such a signal is set, the engine control unit briefly retards the ignition, and the engine torque is reduced. This in turn improves the quality of the gearshifts. It is possible in this way to achieve smoother shifts.Gearbox control unitEngine control unitOTProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP40_2120GB Function DiagramLegend of function diagramon pp. 22 and 23 Components A B/50 D/50 F125 G38 G68 G79 G93 G185 ConnectionsBattery A4 Positive connection 58b in wiring loom Starter (terminal 50) behind dash panel Ignition/starter switch (terminal 50) Multifunction switch U2 Connection 15 in automatic gearbox Gearbox speed sender wiring loom Vehicle speed sender Accelerator pedal position sender 131 Earth connection in engine compartment ATF temperature sender wiring loom Sender 2 for accelerator pedal position 199 Earth connection in wiring loom behind G187 Angle sender for throttle valve dash panel drive J207 Starter lockout relay J217 Automatic gearbox control unit J285 Control unit in dash panel insert J301 AC control unit Colour coding J519 Vehicle electrical system control unit = Input signal J537 4LV engine control unit K142 Indicator light for accelerator pedal = Output signal position P/N L101 Lighting for selector lever scale = Battery positive N88 … 93 Solenoid valves 1 to 6 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted N110 Selector lever lock solenoid unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability = Earth with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� N280 AC compressor control valve S Fuse = CAN databus Y6 Selector lever position display ……/A (Drive) ……/K (Convenience) = Diagnostic connectionThe function diagram represents a simplified current flow diagram. It provides information on the connections of the gearbox management system in combination with the 1.4-ltr./55 kW engine, code AUA.The function diagram is shown without cruise control system.GB21 Function Diagram+15+30 +15SSSSD/50J207G38G68B/50 +A2210936355 J217-45 68 U2 F125424041444319186448Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�N881993122Legend to function diagram refer to p. 21GB J519+30 +15CAN-H/ACAN-H/KCAN-L/ASJ537CAN-L/K J301G185G79G187N2801615J285Y6 49 50 26 66 25 23 34 1 A4Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�υN89N90N91N92N93G93L101K142N110131SP40_5831inGBout23 Self-DiagnosisSelf-diagnosis is used to activate the signals of the sensors, to operate the actuators and to conduct a self-check of the gearbox control units (engine, gearbox). If a fault occurs, the control units activate substitute functions and the fault descriptions (fault code) are stored in the fault memory (permanent memory) of the control unit. Consequently, the fault entries are retained even if the battery is disconnected and the connector of the control unit is unplugged. Self-diagnosis can be carried out using the vehicle system tester V.A.G 1552, the fault reader V.A.G 1551 or the vehicle diagnosis, measuring and information system VAS 5051.1 4 7 8 O Q 5 9HELP2 63It is initiated by entering the address word 02 Gearbox electronics. The following functions are possible in the data transfer with the "address word 02 Gearbox electronics":CV.A.G. 1552SP40_6101 - Interrogating control unit version Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 02 - Interrogating fault memory unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability 04 - Initiating basic setting with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� 05 - Erasing fault memory 06 - Ending output Note: 08 - Reading measured value block You will find detailed procedures for self-diagnosis in the Workshop Manual.SP40_60Function 01 - Interrogating control unit versionPart number of control unitGearbox designationProgramme status001927749 Coding 00000AG4 Gearbox 0010172 WSC 00000not required at presentWorkshop code24GB Function 02 - Interrogating fault memory Any faults relating to the components identified below in colour, are output in this function.PAUFN EIN AUSProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP40_22Function 04 - Basic setting After completing certain repairs or replacing components, it is necessary to perform a new basic setting. A basic setting should always be performed after completing the following actions: – – – – – – Replacing engine, replacing throttle valve drive Removing and installing or replacing gearbox Replacing or coding engine control unit Replacing the accelerator pedal position sender G79 Replacing the automatic gearbox control unit Interrupting the voltage supply of the automatic gearbox control unit (e.g. disconnecting the battery)Function 08 - Reading measured value block This function is used to test the components in the measured value block.Note: Please refer to the Workshop Manual for the individual fault codes.GB25 Mechanical/Hydraulic1 2 B2 K2 K1 F B1 K3181731615Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�4 514131267 8 91011SP40_5726GB LegendComponents 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ATF pump Gearbox housing Cover for gearbox housing Small sun wheel Large sun wheel Input gear (hollow gear) Output gear Park lock gear Drive pinion Differential Drive gear for speedometer Torque converter housing Turbine wheel Pump wheel Freewheel (torque converter)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Turbine shaft unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�B1 B2 F K1 K2 K3Multi-disc brake Band brake with hydraulic cylinder Freewheel (gearbox) Multi-disc clutch Multi-disc clutch Multi-disc clutchTorque converterLockup clutch (closed)Use of the shift elements in individual selector lever positions Selector lever position K1 P R N D 3 2 1 – – – 4th gear 3rd gear 2nd gear 1st gear B2 K3 Shift elements B1 K2 F 8GB27 Mechanical/HydraulicThe mechanical elementsperform the task of absorbing the torque of the engine and passing it on through the final drive to the wheels. The Ravigneaux planetary gear set produces the gear ratio in combination with clutches and brakes. The final drive passes the torque on to the wheels.Schematic diagramBrake Drive gear (hollow gear) Freewheel Clutch Torque converter Brakefrom engineClutchClutch GearingRavigneaux planetary gear setOutput gear Drive pinionto wheel driveto wheel driveSP40_23Final drive gearDifferentialPark lock gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�28GB Overview of componentsFunction diagramB2 F K2B1 K3K1F - FreewheelB1 - Multi-disc brakeB2 - Band brake with hydraulic cylinder K1, K2, K3 - Multi-disc clutchesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP40_24GB29 Mechanical/HydraulicTorque converter with lockup clutchIt is firmly connected to the crankshaft by means of the driven plate and transmits the torque of the engine hydrodynamically to the gearbox. When the torque converter lockup clutch is closed, the torque is transmitted mechanically by means of the friction lining of the lockup clutch. This in turn improves the efficiency of the gearbox. The ATF pump is driven by the torque converter.SP40_25Torque converterThe torque converter lockup clutch is integrated in the torque converter. The lockup clutch of the torque converter operates only in 3rd and 4th gear.Friction lining of lockup clutchProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Note: If the lockup clutch is faulty, it is then necessary to replace the entire torque converter.Lockup clutch Damping springSP40_3030GB Schematic diagram of operations of torque converter lockup clutchopened: The ATF pressure is directed through the lockup clutch slide valve in the control valve body to passage A and thus to a position "upstream" of the lockup clutch. The ATF pressure "upstream" and "downstream" of the lockup clutch is the same. The clutch is open. The solenoid valves are operated through the gearbox control unit. Solenoid valve N91 is not energized.Lockup clutch openedFront side of lockup clutchN91Lockup clutch slide valve ATF flow pressure Gearbox control unitJ217SP40_31closed: Solenoid valve N91 is actuated in order to close the lockup clutch. When this is done, the lockup clutch slide valve is operated and the ATF flow is directed through passage C "downstream" of the lockup clutch. Passage A is opened and acts as an ATF outlet. The oil pressure "downstream" of the lockup clutch is greater than that "upstream" of the lockup clutch. The lockup clutch closes gently and free of jerks. The mechanical connection is produced by means of the friction lining on the lockup clutch.Lockup clutch closed Rear of lockup clutchN91Lockup clutchJ217The ATF pressure is controlled by means of solenoid valve N91.ATF flow valve Protected by copyright. Copying for private or commercial purposes,slide in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability pressure with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Gearbox control unitSP40_32GB31 Mechanical/HydraulicThe working mediumin the hydraulic system of the gearbox is a special oil for automatic gearboxes known as ATF - Automatic Transmission Fluid. This oil is capable of transmitting the torque of the engine through the torque converter into the gearbox. The working temperature range of the oil is approximately from –30 ˚C up to +150 ˚C. The fluid is subjected to severe stresses, which is why it is mandatory to always use the specified ATF. An incorrect ATF can result in the gearbox being destroyed after only a short distance. Tasks of the ATF – – – – – – Transmitting the torque in the torque converter Operating the shift elements, clutches and brakes Dissipating the heat into the ATF cooler Lubricating all the rotating gearbox parts Permitting friction (in the multi-disc clutches and brakes, in the lockup clutch) Transporting off abrasionNote: You can find more details on ATF in SSP 20/21.ATF pumpThe pump is driven by the torque converter which is coupled directly to the engine. The pump draws the ATF out of the oil pan and pumps it through the control valve body into the oil circuit. The ATF pump operates on the same principle as a gear pump.ATF coolerAn ATF cooler is integrated in the oil circuit in order to cool the ATF which is subjected to high thermal stresses. This cooler is mounted directly on the gearbox and is integrated in the coolant circuit of the engine.Inlet sideProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP40_26Delivery sideSP40_6232GB Diagram of oil circuitATF pumpClutch from crankshaft Gear slide valve Torque converterSolenoid valveSP40_29Control valve body ATF filter Inlet side Delivery sideMain pressure slide valveControl valve body with solenoid valvesThe solenoid valves integrated in the control valve body, open and close the passages to the matching clutches and brakes in order to operate the individual gears.N89 N91N88 N92N90Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�N93SP40_18GB33 Mechanical/HydraulicPlanetary gear setOnly a short and a long planetary gear are shown in the right-hand diagram to more easily recognise how they operate.Small sun wheelShort planetary gear Long planetary gearLarge sun wheelPlanetary carrierHollow gearSP40_53SP40_27Small sun wheelLarge sun wheelFinal drive with park lockPark lockPark lock gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP40_2834GB FreewheelThe freewheel is designed as a clamping body freewheel. In the blocking direction, the asymmetricallyshaped clamping bodies move up against the freewheel and hold it tight. This prevents the planet carrier from also rotating. In 1st gear it is therefore possible to utilise the braking action of the engine.ReleasedNon-clamped stateBlocking direction Clamped stateNote: You can find out more on the freewheel F in SSP 20.Park lockThe park lock provides an additional protection in combination with the parking brake to prevent the vehicle from rolling away. It is engaged in a purely mechanical way when the car is stationary and the selector lever is moved into position "P". The park lock acts on the intermediate gear stage of the automatic gearbox. The park lock is firmly attached on the drive pinion - in the same way as the output gear of the intermediate gear stage. If the selector lever is moved into position "P", a shift shaft pushes the park lock into a gap in the teeth of the Protected park lock gear. by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. the ŠKODA AUTO A. S. does not guarantee or accept any liability The intermediate gear stage is blocked, with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� vehicle safeguarded.SP40_33GB35 Mechanical/HydraulicShift elements Multi-disc clutches K1, K2, K3Closing the clutch The ATF is forced into the space "upstream" of the piston. The ball valve closes. The ATF pushes the piston against the clutch plates and closes the clutch.Oil Ball valve Piston Clutch platesSP40_34AirSpringOpening the clutch The ATF pressure "upstream" of the piston is reduced. The ball valve in the piston opens as a consequence of the centrifugal force acting on the ball. The spring pushes the piston back into its initial position. The ATF is forced out of the space "upstream" of the piston.Clutch plates Piston Ball valve Clutch playOilNote: The clutch play ensures that the clutch does not rub when it is not operated. This play must be re-set after carrying out repairs on the clutch.SP40_35AirSpringAirProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�36GB Multi-disc brakeBrake B1 is a multi-disc brake. It brakes the planet carrier and holds it tight. Its operation is practically identical to that of a multi-disc clutch.Gearbox housing SpringBrake closed The brake is operated in selector lever position 1, and in reverse gear. In view of the fact that the planet carrier is held tight, it is possible to exploit the engine braking power in 1st gear.OilPiston Brake discsSP40_36Cover for gearbox housingBrake openedProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The brake play ensures that the brake does not rub when it is not operated. The brake play must be re-set after carrying out repairs.Brake playGearbox housing SpringOilPiston Brake discsSP40_37Cover for gearbox housingGB37 Mechanical/HydraulicBand brakeBrake B2 is a band brake. It is operated by a hydraulic cylinder. A brake band holds the large sun wheel tight in 2nd and 4th gear through clutch K2.B2 K2K1SP40_38Large sun wheelHydraulic cylinderSP40_63Hydraulic cylinder 4th gear operating piston2nd gear operating pistonPiston stemBrake bandProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Clutch K2SP40_40SP40_3938GB 2nd gear operation The pressure of the ATF acting on the 2nd gear operation piston pushes the piston stem down. The brake band is tensioned. The rotational movement of clutch K2 is interrupted and the large sun wheel is held tight.2nd gear operating pressure Gearbox housingSpring2nd gear operating piston Piston stemSP40_41Brake band3rd gear operation The 3rd gear release pressure pushes the 2nd gear operating piston back into its initial position. The brake band is opened. Clutch K2 and the large sun wheel again rotate.Spring Gearbox housing 3rd gear release pressurePiston stemBrake bandSP40_424th gear operating piston4th gear operation Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted operating unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� pressure The pressure of the ATF acting on the 4th gear operation piston pushes the piston stem down. The brake band is tensioned. The rotational movement of clutch K2 is interrupted.Spring Gearbox housing4th gearPiston stemSP40_43Brake bandGB39 Power FlowThe illustration shows only one set of the three sets of planetary gears in the function diagram in order to better understand the function. The control unit actuates the solenoid valves in the control valve body which in turn operate the relevant clutches and brakes in line with the drive position selected by the driver.Clutches K1, K2 and K3 transmit the power to the planetary gear set.–B1 - Brake B1 holds the planet carrier tight. B2 - Brake B2 holds the large sun wheel tight.–– K1 - Clutch K1 drives the small sun wheel. – K2 - Clutch K2 drives the large sun wheel. K3 - Clutch K3 drives the planet carrier. The input gear (hollow gear) transmits the power to the output gear of the drive pinion. F - Freewheel––Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�40GB Short planetary gear Input gear (hollow gear) FreewheelB2 F K2B1 K3Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Planet carrierK1Long planetary gearSP40_44Small sun wheel Large sun wheel Output gear on drive pinionGB41 Power FlowDepending on whether the lockup clutch is "opened" or "closed", it is possible to distinguish between a "hydraulic" and a "mechanical" power flow.Hydraulic power flowThe lockup clutch is "opened". The torque converter transmits the power of the engine hydraulically and passes it on to the gearbox.Engine Clutch K2Clutch K1Clutch K3Turbine wheelPump wheelTurbine shaftSP40_45Lockup clutch "opened"Turbine wheelPump wheelTorque converter Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability freewheelwith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP40_46Torque converter housingTurbine shaft42GB Mechanical power flowThe lockup clutch is "closed". The power of the engine is transmitted to the gearbox through the friction lining of the lockup clutch.EngineClutch K1 Clutch K2Clutch K3Torque converter housingLockup clutchTurbine shaftSP40_47Lockup clutch "closed"Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP40_48Torque converter housingTurbine shaft 43GB Power FlowThe examples below are intended to illustrate the interaction of the clutches and brakes for 1st gear, reverse gear and 4th gear with the lockup clutch (opened or closed).Selector lever position "D" 1st gearPump wheelTPB2 K2FB1 K3SP40_49Turbine wheelPlanet carrierK1Small sun wheelPump wheel Turbine wheel Clutch K1 drives the small sun wheel The planet carrier orbits around the freewheelSolenoid valves N88 and N92 actuatedProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Selector lever position "R" Reverse gearPump wheelB2 K2 B1 K3TPFSP40_50Turbine wheelK1Planet carrier Large sun wheelPump wheel Turbine wheel Clutch K2 drives the large sun wheel Brake B1 holds the planet carrier tight44GB Selector lever position "D" 4th gear hydraulic (lockup clutch open), i.e. torque converter slip occursPump wheelB2 K2 B1 K3TPFSP40_51Turbine wheelK1Planet carrier sun wheelProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Large unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Pump wheel of information in this document. Copyright by ŠKODA AUTO A. S.� with respect to the correctnessTurbine wheel Brake B2 holds the large sun wheel tight Clutch K3 drives the planet carrier Selector lever position "D" 4th gear mechanical (lockup clutch closed), i.e. no torque converter slip occursPump wheelSolenoid valves N88 and N89 actuatedTPB2 K2FB1 K3Torque converter housing Planet carrierK1SP40_52Turbine wheelLarge sun wheelTorque converter housing Lockup clutch Remaining power transmission is identical to 4th gear hydraulicSolenoid valves N88, N89 and N91 actuatedGB45 Test Your KnowledgeWhich answers are correct? Sometimes only one. But, possibly also more than one – or all of them! Please complete the missing points.1.Which gears can still be engaged by operating selector lever after the control unit has failed? A. B. C. reverse gear 3rd gear 1st gear2.If it is to operate properly, the automatic gearbox control unit J217 requires signals from 8 sensors. Which sensor signals flow to the 4LV control unit J537 (engine control unit)? A. B. C. D. E. F. G. H. I. Kickdown switch F8 Multifunction switch F125 Accelerator pedal position sender G79 Gearbox speed sender G38 Brake light switch F ATF temperature sender G93 Vehicle speed sender G68 Angle sender for throttle valve drive G187 Accelerator pedal position sender G1853.The multifunction switch F125 detects the position of selector lever and passes this on to the control unit. What are the effects if this switch fails? A. B. C. The engine can no longer be started. The automatic gearbox control unit switches to an emergency mode programme. The reversing lights can no longer be switched on.4.The ATF temperature sender G93 constantly monitors the temperature of the ATF. What are the effects if the sender detects a temperature below –25 ˚C? A. B. C. no effects hard gearshifts 4th gear is not engaged.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�46GB 5.What complaints might a customer have if the gearbox speed sender G38 has failed? A. B. C. The gearbox does not shift into 4th gear. The gearshifts are hard. The reversing lights do not operate.6.Which solenoid valve is actuated in order to close the lockup clutch? A. B. C. Solenoid valve N90 Solenoid valve N91 Solenoid valve N897.After replacing which components is it necessary to carry out a basic setting of the automatic gearbox control unit? A. B. C. D. after replacing the throttle valve control unit after replacing the engine control unit after replacing the engine after replacing the automatic gearbox control unit8.In which gears is the lockup clutch closed? A. B. C. in 1st and 2nd gear in 2nd, 3rd and 4th gear in 3rd and 4th gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB1. A., B., C.; 2. C., H., I.; 3. A., B., C.; 4. C.; 5. A., B.; 6. B.; 7. A., B., C., D.; 8. C. Answers47