TECHNICAL DOCUMENTATION
SSP 055 2,0 110kW 1,6 85kW FSI engine

This PDF is currently unavailable.
Read document text
The FSI technology (Fuel Stratified Injection = Injection with stratified charge) adds a new dimension to the 2.0-ltr. and 1.6-ltr. petrol engines. FSI engines are more economical, cleaner and more agile than an intake manifold injector. These new engines fulfil optimally the current demands for a lower consumption, a better environmental balance and a high driving satisfaction. For Škoda vehicles, the FSI engines are available in the new ŠkodaOctavia. In this Self-Study Programme you can get acquainted with the technical innovations of these engines.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�2GBContentsPart I – 2.0-ltr. FSI engineEngine mechanical components Engine highlights Cylinder block Crankcase breather Intake manifold - bottom part Piston The cylinder head Camshaft adjustment Engine lubrication Oil circulation Oil filter module Engine management Intake manifold with switching roller Intake air guide and operation modes Double injection Fuel supply Fuel pump control unit J538 Fuel system regulated as needed Fuel-high pressure pump Parts of the fuel system Exhaust system Exhaust system Exhaust system Regeneration of the storage catalytic converter NOx Sender Exhaust gas recirculation 4 4 6 6 7 7 8 9 15 15 15 16 16 17 22 25 25 26 28 30 32 32 34 36 38 39Part II – 1.6-ltr. FSI engineEngine mechanical components Chain drive Camshaft adjustment Sealing the timing case Oil pump Engine cover Intake manifold Cooling Two-circuit cooling system Cooling system overview Exhaust gas recirculation valve N18 AGR Sensors Sensors and senders Appendix PCV control valve for 1.6-ltr. FSI engine Piston shape 2.0-ltr. FSI engine Piston shape 1.6-ltr. FSI engine System overview Function diagraServiceOCTAVIA IIII OCTAVIAXXXXXXXXXXXXXXXX XXXXXXX40 41 42 43 44 46 47 48 48 50 51 52 52 55 55 55 55 56 58ServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXXXXXXXX XXXXXXXS e r v i c eYou will find notes on inspection and maintenance, setting and repair instructions Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted in the Workshop Manual. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilityXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXwith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB3Engine mechanical componentsPart I – 2.0-ltr. FSI engineSP55_01Engine highlights– One piston high pressure pump – Plastic switching intake manifold – Intake manifold bottom part with continuously adjustable intake manifold flaps – Cooled exhaust gas recirculation valve – Roller rocker arm with hydraulic supporting elementsProtected by copyright. Copying for continuous private or commercial purposes, in part or in whole, is not permitted – Two overhead camshafts (DOHC) with inlet camshaft adjustment unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�– Balance shaft transmission in the oil pan – Beam guided combustion procedureNote: If not specified otherwise, the illustrations and the descriptions in part I of this brochure refer to the 2.0-ltr./110 KW FSI engine with the code letters BLX.4GBTechnical Data stratified and homogeneous BLXFSI Versions Engine code letters Design Displacement Bore Stroke Compression ratio Valves per cylinder Firing order max. power output max. torque Engine management Fuel Emission standardhomogeneous BLR 4-cylinder inline engine 1984 cm3 82.5 mm 92.8 mm 11.5 : 1 4 1–3–4–2 110 kW at 6000 rpm–1 200 Nm at 3500 rpm–1 Bosch Motronic MED 9.5.10homogeneous BLY10.5 : 1Petrol 98 (95) RON EU4Petrol 95 (91) RONEU2Technical highlights Engine code letters: BLX 150 Type: Inline engine Number of cylinders: 4 135 Valves per cylinder: 4 Compression ratio: 11.5 : 1 120 Displacement: 1984 cm3 Bore diameter: 82.5 mm Protected by copyright. Copying for private or commercial purposes, in part or in 105 whole, is not permitted Stroke:unless authorised by ŠKODA AUTO 92.8 mm A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Valve control: Roller rocker arm 90 with hydraulic supporting elements 75 max. power output: 110 kW at 6000 rpm max. torque: 200 Nm at 3500 rpm Engine management: Bosch Motronic 60 MED 9.5.10 Fuel: Petrol Super Plus 45 Unleaded 98 RON (Super Unleaded 95 30 RON is possible, with low reduction in 15 performance) Exhaust after treatment: NOx storage catalytic converter und 2 pre0 1000 2000 catalytic converters Emission standard: EU4P (kW) 300270240210180150 M (Nm)12090603030004000500060007000n (min –1 )SP55_02GB5Engine mechanical componentsCylinder blockThe cylinder block consists of an aluminum alloy and is the most compact unit of its category with a cylinder distance of 88 mm and an overall length of only 460 mm.SP55_03unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Crankcase breather with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedThe gases from the combustion chamber, which are pushed past the piston into the crankcase, bind oil particles and penetrate into the oil separator. The majority of the oil particles is separated from the gases in the oil separator.The gases are led via the hose connector into the integrated labyrinth of the cylinder head cover. From there they reach as almost oil-free blow-by gases the intake manifold via the pressure regulator valve.Labyrinth Cylinder head coverHose connectionOil separatorSP55_046GBIntake manifold - bottom partThe intake manifold bottom part is bolted to the fuel distribution pipe. In the intake manifold bottom part, there are four intake manifold flaps, which are adjusted by the intake manifold flap motor V157 via a common shaft. The potentiometer for the intake manifold flap G336, which is integrated in this engine, serves as feedback for the flap position at the Motronic control unit J220Intake manifold flap motor V157(Engine control unit). The position of the intake manifold flaps influences the mixture formation and thus the exhaust gas values. The actuation of the intake manifold flaps belongs to the exhaust gas relevant systems and is monitored by the EOBD.Fuel feed for injection valveIntake manifold flap motor V157Fuel pressure sender G247SP55_28SP55_46Fuel distributor pipe Fuel distributor pipe Intake manifold flapPistonLightweight constructed smooth shank piston out of aluminum alloy with closely positioned piston pin bosses. Advantage: smaller reciprocating masses and lower friction values, as the piston shaft runs only with part of the circumference in the cylinder.SP55_09A flow recess, which guides the air flow in the stratified charge mode towards the spark plug is integrated into the piston crown. The geometrical shaping of the piston sets the air flow into a rolling motion (Tumble-Effect).Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP55_10GB7Engine mechanical componentsThe cylinder headwith 4-valve technology and roller rocker arm is adapted to the direct injection procedure: The valve control is performed via two overhead camshafts, which are mounted torsionally stiff in a ladder frame. The drive of the exhaust camshaft is performed by means of the toothed belt, which in turn drives the inlet camshaft via a single chain. Each suction channel is divided through a tumble plate into an upper and lower half. Due to its shaping no incorrect assembly is possible. The mounts of the high pressure injection valves are integrated into the cylinder head, whereby the high pressure injection valves protrude directly into the combustion chamber.Ladder frameExhaust camshaftInlet camshaftCylinder headProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP55_12Tumble plate8GBPositioning of the camshafts to each other The inlet and exhaust camshaft must be turned to each other, so that the markings are positioned exactly opposite each other. The drive chain must be positioned in this camshaft position, without taking into account the number of rollers. The cylinder head bolts can only be screwed in and unscrewed in this position.SP55_16Cylinder head boltNote: You will find the tightening torque of the cylinder head bolts in the current repair manual.Camshaft adjustmentOnly the inlet camshaft is adjusted. The camshaft adjuster is located on the exhaust camshaft. The inlet camshaft is equipped at the one end with the Hall sensor rotor and at the other end with the double cams for the drive of the fuelhigh pressure pump.Marking Hall sensor rotor Exhaust camshaft Camshaft adjuster Chain sprocket at camshaft adjusterInlet camshaftProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the Toothed correctness of belt information in this document. Copyright by ŠKODA AUTO A. S.�SP55_15Drive chain Chain tensioner Double camsGB9Engine mechanical componentsStructure of the camshaft adjuster The inlet camshaft is hydraulically mapcontrolled adjusted with a camshaft adjuster continuously up to 42° crankshaft angle (21° camshaft angle). The toothed belt drives the exhaust camshaft and the exhaust camshaft accomodates on the opposite side the internal rotor of the camshaft adjuster. The external rotor is bolted to the front and rear cover of the camshaft adjuster. The chain spocket is a component of the rear cover and for this reason the external rotor is also connected to the chain sprocket. The twisting of the external rotor towards the internal rotor is transferred via the drive chain onto the inlet camshaft. Thus, the timing of the inlet valves is changed.Rear cover Internal rotor Front cover Oil boreChain sprocket at camshaft adjuster Oil bore External rotor Locking pin Washer Inlet camshaft timing adjustment valve -1- N205 Spring ScrewSP55_73Oil supply moduleNon-return valveThe inlet camshaft timing adjustment valve N205 is an important component of the oil supply module. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The oil supply module is integrated with the drive chain, the chain tensioner and the double cams into the cover for the camshaft adjuster.Cover 10SP55_53GBWorking mode The camshaft adjuster is supplied with oil from the engine oil pump via the oil channels in the cylinder block, cylinder head and oil supply module. The different filling of the working chambers with oil, located next to the tabs of the internal rotor, leads to a twisting of the external rotor in relation to the internal rotor. The inlet camshaft timing adjustment valve -1- N205 is actuated by the engine control unit and regulates in line with the engine speed, load and coolant temperature, the adjustment of the inlet camshaft up to 21°.Camshaft adjuster unpressurized The inlet camshaft timing adjustment valve N205 is de-energized. The spring-tensioned locking pin is latched into a recess in the rear cover of the camshaft adjuster. It prevents a twisting of the external rotor (and at the same time an adjustment of the intake camshaft) during the starting procedure. The external rotor and therefore also the inlet camshaft are located in the “late position”.Internal rotor External rotor in “Late” positionRear coverFront cover21°Oil boreProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�WasherSP55_54 SP55_55Working chamberRecess Tab of internal rotor Locking pin latchedGB11Engine mechanical componentsUnlatch the locking pin The inlet camshaft timing adjustment valve 1 N205 opens the access to the working chamber B. The flowing oil flows through the recess in the rear cover under the locking pin and raises it. The locking pin unlatches and the external rotor moves in the direction of “Early position”– red arrow.Oil feed into the working chambers BProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Oil return from the working chambers ASP55_56Oil feedOil return Locking pin unlatched Rear cover External rotor in “Late” position RecessInternal rotorSpringWorking chamber BSP55_57 SP55_60Oil bore Working chamber AFront coverNote: If the engine is switched off, the oil pressure in the working chambers drops and the locking pin latches again by means of the spring.12GBExternal rotor in “Control” position The inlet camshaft timing adjustment valve 1 N205 is adjusted in such a way that both working chambers are pressurized with oil. Depending on the different oil pressures in the working chambers A and B the external rotor (red double arrow) adjusts itself and therefore also the inlet camshaft towards "Early" or "Late". The actuation enables a continuous camshaft adjustment.Internal rotorExternal rotor in “Control” positionWorking chamber BSP55_59Working chamber AExternal rotor in “Early” position If the oil pressure in the working chambers B increases, the external rotor moves further towards “early” (red arrow), until it reaches the “Early” position. The external rotor and therefore also the inlet camshaft are located in the “Early” position.External rotor in Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability “Early” position with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Internal rotorWorking chamber BSP55_62Working chamber AGB13Engine mechanical componentsExternal rotor in “Late” position When adjusting from “early” to “late”, the inlet camshaft timing adjustment valve 1 N205 is adjusted in such a way that the oil flows into the working chambers A. The oil pressure in the working chambers B decreases. The external rotor moves back into the “Late” position - red arrow.Internal rotor Oil return from the working chambers B External rotor in “Early” positionOil feed into the working chambers ASP55_61Oil feedOil returnCopying for private or commercial purposes, in part or in whole, is not permitted Protected by copyright. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Working chamber ASP55_63Working chamber BAn oil bore is located in the tab of the internal rotor, so that the locking pin does not latch in the “Late” position. The oil from the working chamber A flows through this oil bore into the slot under the locking pin shoulder. The oil pressure maintains the spring-tensioned locking pin in the unlatched position.Internal rotorExternal rotor in “Late” positionOil feed from the working chamber AOil bore SlotWorking chamber BSP55_64Working chamber A Oil bore Tab of internal rotor Locking pin unlatchedSP55_5814GBEngine lubricationOil circulationThrough converting to the 4-valve cylinder head with roller rocker arm, the oil gallery differs substantially from the 5-valve cylinder head with bucket tappet. The oil passes between the 3rd and 4th cylinder in the cylinder head via the main oil channel of the cylinder block. The hydraulic supporting elements and the camshaft bearings are supplied with oil pressure by two oil channels. There is a spray bore in the supporting elements, which serves as oil supply for the roller rocker arms. During the further course of the oil channels, the camshaft adjuster is pressurized with oil pressure for the camshaft adjustment.SP55_11Settling chamber for crankcase ventilationProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Oil filter moduleThe new oil filter module was developed as a highly integrated plastic unit and contains the following units: – Pressure relief valve – Oil filter with paper filter element – Coolant flow around oil cooler – Settling chamber for the coarse oil separator of the crankcase ventilationOil outletOil cooler Coolant inletOil inletCoolant outlet Pressure relief valveSP55_27Paper filter element Oil drain valveGB15Engine managementIntake manifold with switching rollerThe two-stage switching intake manifold improves the desired power output and torque characteristics. The pneumatic actuation of the switching roller from the torque position to the power output position is performed map-controlled. Load, engine speed and coolant temperature are relevant sizes for this.Switching rollerPower channelThe switching roller is in the power output position. The engine draws in air via the power and the torque channel.Torque channelSP55_29The switching roller is in the torque position. The engine draws in air only via the torque channel.SP55_30Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�16GBIntake air guide and operation modesIn contrast to conventional petrol engines, which depend on a homogeneous air-fuel-mixture, engines with gasoline direct injection (FSI), functioning according to the lean concept, can be operated in the partial load range through well-directed stratified charge with high excess air. The FSI method creates two substantial operation modes, the homogeneous mode in the full load range and the stratified charge mode in the partial load range.Homogeneous mode The drawn in air mass is guided in both parts of the suction channel (above and below the tumble plate) into the combustion chamber, if the intake manifold flap is open. This air guide makes the homogeneous mode possible.Drawn in airThrottle valveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP55_31Intake manifold open Tumble plateStratified charge mode The drawn in air mass is only guided in the suction channel above the tumble plate into the combustion chamber, if the intake manifold flap is closed. This air guide is used for the stratified charge mode.Drawn in airThrottle valveIntake manifold closed Tumble plateGBSP55_3217Engine managementHomogeneous mode In the upper load and speed range the intake manifold flap is opened, so that the drawn in air mass can flow into the cylinder via the upper and lower suction channel.Throttle valve Spark plugIntake manifold openTumble plateHigh pressure injection valveSP55_33Drawn in air massThe fuel injection is performed in the suction phase and thereby a homogeneous (14.7:1) filling occurs in the cylinder.Fuel Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP55_3418GBThe air-fuel mixture has far more time to mix optimally, when injection is performed during the intake stroke.Homogeneous air-fuel mixtureSP55_35The combustion takes place in the whole combustion chamber.Burning air-fuel mixtureProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP55_36The advantages in the homogeneous mode result from direct injection in the intake stroke, whereby part of the warmth is extracted from the drawn in air mass through the vapors of the fuel. The knock tendency is reduced through the interior cooling; consequently the engine compression can be increased and the degree of efficiency is improved.GB19Engine managementStratified charge mode So that there is a stratified charge, the injection, the combustion chamber geometry as well as the interior current in the cylinder must be optimally co-ordinated. In addition, certain requirements must be fulfilled. These are: – Engine is in the corresponding load and speed range. – No exhaust gas relevant fault in the system. – Coolant temperature above 50 °C. – The temperature of NOx storage catalytic converter must be between 250 and 500 °C. – The intake manifold flap must be closed.SP55_37Throttle valve Drawn in air massIn the stratified charge mode, the intake manifold flap closes the lower suction channel Intake completely. The drawn in air mass only flows manifold flap via the upper suction channel with a smaller cross-section and thus is accelerated. Afterwards it flows roller-shaped into the cylinder. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Tumble plateHigh pressure injection valveSP55_38The tumble effect is still strengthened by the flow recess in the piston. At the same time the throttle valve is opened far enough, in order to keep the throttle losses as low as possible.SP55_3920GBDuring the combustion stroke and shortly before ignition timing, fuel is injected under high pressure (5 to 11 MPa) into the close range of the spark plugs.FuelSP55_40As the injection direction points directly to the spark plug, the fuel cloud rarely comes into contact with the piston We are talking Protected by copyright. Copying for crown. private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability about a “beam guided” combustion with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� procedure.Fuel cloudSP55_41Ignited mixtureA well ignitable mixture cloud forms within the close range of the spark plugs, which is ignited in the compression phase. Additionally after combustion, there is an isolating air layer between the ignited mixture and the cylinder wall. This leads to a reduction of the heat dissipation via the engine block.Isolating air layerSP55_42GB21Engine managementDouble injectionTwo other operation modes have been added to the previously described operation modes. The operation modes are: – Double injection catalytic converter heating – Double injection full load. Thus, on the one hand the catalytic converter is heated much faster and on the other hand the torque is increased in the lower speed range.Double injection catalytic converter heating During double injection catalytic converter heating, the catalytic converter is heated up much faster and it reaches its operating temperature much earlier. In addition, quiet running is improved and fewer HC emissions develop. Everything together leads to a reduction in exhaust emissions and consumption.F ir st inject ion The first injection is performed approx. 300° KW before ignition TDC during the intake stroke. This results in an equal distribution of the airfuel mixture.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 1st injection unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP55_48S econd injection For the second injection, a small amount of fuel approx. 60° KW is additionally injected before ignition TDC. This mixture burns very late and the exhaust gas temperature increases.2st injectionSP55_49The warmer exhaust gas warms up the catalytic converter and it reaches its operating temperature more rapidly.to the catalytic converterSP55_5022GBDouble injection full load Petrol direct injections at speeds up to 3000 rpm as well as full load can partially result in an undesirable uneven mixture distribution. This is prevented through the use of a double injection and a torque increase of 1–3 Nm is achieved.F i r s t inject ion The first injection is performed once again approx. 300° KW before ignition TDC during the intake stroke. At the same time approximately two thirds of the total fuel quantity to be injected, is injected.1st injectionSP55_51S e cond inject ion The remaining fuel quantity, approximately one third, is injected just at the beginning of the compression stroke. Thus, less fuel is deposited at the cylinder wall. The fuel evaporates nearly completely and the mixture distribution is improved. In addition, there is a richer mixture in the area of the spark plug than in the rest of the combustion chamber. This improves the combustion cycle and reduces the knocking tendency.2st injectionSP55_52Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB23Engine managementOperation modes The beam guided combustion procedure enables a homogeneous and a stratified charge mode. Depending on load condition and position of the accelerator pedal, the engine control unit selects the optimal operation mode. In the stratified charge mode, the fuel air mixture in the combustion chamber is λ = 1.60 – 4.00 (excess air). 4 main operation modes are driven: – stratified lean with λ = 1.6 – 4.00 and exhaust gas recirculation (= EGR) – homogeneous lean with λ = 1.55 without EGRProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability – homogeneous unless with λ = 1 by and EGR with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�At increasing speed, the time for the mixture formation in the combustion chamber is shortened. An adequately ignitable mixture cannot be produced. The engine control unit switches into the homogeneous mode, in order to ensure a safe mixture formation. The fuel-air mixture is enriched and is reduced in stages to λ = 1 .– homogeneous with λ = 1 without EGRhomogeneous withλ = 1 without EGRhomogeneous withλ = 1 and EGRhomogeneous lean without EGRstratified lean with EGRSP55_43n = Engine speed p = Average pressure24GBFuel supplyFuel pump control unit F538The control unit is fitted on the right under the rear seat bench in the cover of the electrical fuel pump for pre-supply.Task The fuel pump control unit J538 actuates the electrical fuel pump for pre-supply and regulates the pressure in the low pressure fuel system in the range of 0.05-0.5 MPa. The pressure is increased to 0.6 MPa at hot and cold start.SP55_24Effects of signal failure If the signal of the fuel pump control unit fails, Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by Š KODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability an engine operation is not possible.with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Electrical circuit G G1 G6 J220 J285 J519 J538 Fuel gauge sender Fuel gauge Fuel pump for pre-supply Motronic control unit (engine control unit) Dash panel insert control unit Onboard supply control unit Fuel pump control unitKl. 30 Kl. 15 J519 S S G G6J538The fuel gauge sender G is supplied with signal mass from the fuel pump control unit J538. The signal mass in turn comes from the control unit in the dash panel insert J285.J285T94/4831G1J220SP55_45GB25Fuel supplyFuel system regulated as neededThe electrical fuel pump for pre-supply delivers only as much fuel to the fuel high-pressure pump as it needs. This reduces the electrical power absorption capacity and the fuel consumption drops. Note: If the engine control unit or the electrical fuel pump for pre-supply is replaced, an adaptation must be carried out. For this reason, please oberve the notes in the mode of operation “Targeted Fault Finding” of the VAS 5051.Driver door contact switch F2 Onboard supply control unit J519BatteryMotronic control unit J220Fuel pressure sender, low pressure G410 Fuel pump control unit F538 Pressure regulator valveFuel feed line Fuel filterProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Electrical fuel pump for pre-supply G6Fuel tankSupply voltage Output signalunpressurized 0.05 to 0.6 MPa – Low pressureInput signal Earth 26 5 to 11 MPa – High pressureGBLow pressure fuel system In the low pressure fuel system, the fuel pressure in the normal mode is in the range of 0.05-0.5 MPa. The pressure is increased to 0.6 MPa at hot and cold start. I t c o nsist s of : • • • • • the fuel feed line the fuel pump control unit J538 the fuel reservoir the electrical fuel pump for pre-supply G6 the fuel pressure sender, low pressure G410High pressure fuel system In the high pressure fuel system, the fuel pressure is between 5 and 11 MPa. I t c o n s i s ts o f: • • • • • • • the fuel-high pressure pump Fuel pressure regulating valve N276 a high pressure fuel line the fuel distributor pipe the pressure regulator valve the fuel pressure sender G247 the injectors for cylinder 1–4 N30 – N33Fuel return-flow line The fuel flows from the fuel distributor pipe, when the pressure regulator valve is opened, via the fuel return – flow line into the fuel feed line.Fuel pressure sender G247 Fuel-high pressure pump High pressure fuel lineProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Pressure regulator valve For the protection of the components opens at a fuel pressure of 12 MPa. Double cams on the inlet camshaft Fuel distributor pipeSP55_23Injectors for cylinder 1–4 N30 – N33 Fuel pressure regulating valve N276GB27Fuel supplyFuel-high pressure pumpThe fuel-high pressure pump for FSI engines is a further development of the conventional fuel pumps. A continuous quantity of fuel with a pressure of up to 0.6 MPa is made available for the fuelhigh pressure pump by an electrical fuel pump for pre-supply in the tank. The fuel-high pressure pump produces a pressure of up to 12 MPa. The high pressure is achieved through the movement of the pump piston of the high-pressure pump, which is driven by a double cam located on the inlet camshaft. The fuel pressure regulating valve N276 is conceptualized for a fuel delivery, which fulfils the demand. The regulating valve consists of a coil, a valve actuation piston and a springtensioned inlet valve. The delivery quantity control is performed by a timely co-ordinated electrical actuation of the regulating valve in line with the angle position of the double cam. If the coil is electrically actuated, it results in a magnetic field and the valve actuation piston is pulled into the coil. The inlet valve is closed and the fuel-high pressure pump delivers the requested fuel quantity.Fuel pressure regulating valve N276 High pressure connectionFlat coverSP55_65Low pressure connectionWhen constructing the fuel-high pressure pump, a weight reduction was consciously observed while simultaneously optimizing the firmness. The developed aluminum diecast housing is covered with a layer of nickel phosphorus for the protection against corrosion. This protective layer makes the inside of the pump resistant to fuel. On the outer layer, the protection against corrosion is increased. Make sure that the coating is not damaged when working on the fuel-high pressure pump.Valve actuation pistonPulsation damping elementLow pressure connectionProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�High pressure connection Exhaust valve Coil High pressure chamberSP55_66Low pressure High pressureInlet valve 28 Pump plungerGBWorking mode A principle sketch of the pump is used for the explanation of the pump actuation. Blue arrows are used for the fuel with low pressure (pre-supply pressure) and red arrows for the fuel with high pressure.S u c t ion f uel The fuel penetrates from the low pressure connection via the inlet valve into the high pressure chamber. The fuel is suctioned into the high pressure chamber through the downward movement of the pump piston during the movement before TDC after BDC of the double cam.SP55_67R e tu r n delivery of the fue l In order to adapt the fuel quantity to the actual Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted consumption, the is not initially unless authorised bycoil ŠKODA AUTO A.excited S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� after reaching the BDC. This means that there is no magnetic field and the inlet valve remains open. The fuel is guided back into the low pressure range. Developing pulsations are intercepted by pulsation damping elements which are integrated in the housing.SP55_68H i g h pr essur e de liv e ry The coil is pressurized with current and tightens the valve actuation piston. The inlet valve is closed. No more fuel can flow back into the low pressure range. A high pressure build-up occurs through the movement of the pump piston. The coil must not be energized permanently. The differential pressure between the high pressure chamber and the low pressure side keeps the inlet valve closed. The compression occurs continuously until the double cam reaches the TDC.SP55_69GB29Fuel supplyParts of the fuel systemFuel distributor pipe The task of the fuel distribution pipe consists of distributing a defined fuel pressure to the pressure injection valves and making an adequate volume available for the balancing of pressure pulsations.Fuel return-flow line Fuel feed line Fuel-high pressure pumpFuel pressure regulating valve N276Fuel pressure sender G410SP55_05Connection for fuel pressure sender G247Connection for High pressure Low pressure pressure regulator Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted connection connection valve unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Fuel distributor pipeConnectorFuel pressure sender G247 The fuel pressure sender has the task, within the overall system, to measure the fuel pressure in the fuel distribution pipe (Rail). The measured pressure is transmitted as an electrical signal for the fuel pressure control to the engine control unit. The analysis electronics integrated into the sensor is supplied with 5 V. When the fuel pressure rises, the resistance decreases and at the same time the signal voltage increases.Housing Contact bridgeASIC*Conductor plate Spacer Sensor element*Application-Specific Integrated CircuidPressure connectionSP55_7030GBInjection valves N30–N33 The injection valve represents the interface between the fuel distribution pipe and the combustion chamber. It is the task of the injection valve to proportion the fuel and to obtain, by means of fine atomization, a purposeful mixing of fuel and air in a certain area of the combustion chamber. When actuating the injection valve, the fuel is injected directly into the combustion chamber on the basis of the pressure difference between the fuel distributor pipe and the combustion chamber.Solenoid coilSolenoid armatureNote: The teflon gasket must be replaced at each disassembly of the injection nozzle - see notes in the repair manual.Nozzle needleTeflon gasketSP55_71Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�N30N31N32N33The engine control unit generates the necessary actuation voltage of 50–90 volt for the injection valves N30-N33. This is necessary, in order to ensure a shorter injection period compared with an intake manifold injection.T60/32 T60/33 T60/31 T60/48 T60/46 T60/44 T60/47 T60/34SP55_72J220GB31Exhaust systemExhaust systemThe exhaust system is executed at two points with 2 strands in the front area, in order to increase the torque in the lower speed range. Each of the two exhaust strands is equipped with a pre-catalytic converter and NOxstorage catalytic converter. The pre-catalytic converters are inseparably connected to the respective exhaust manifold. Two pre-catalytic converter probes (wide band probes) monitor the exhaust composition.Detail without hot air drip panPre-catalytic converter probeConnection for exhaust gas recirculationSP55_74Pre-catalytic converterNOx sensorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�NOxstorage catalytic converter (with three-way structure)32GBPre-catalytic converterHot air drip panConnection for exhaust gas recirculationSP55_75Pre-catalytic converter probe (linear)Notes: For vehicles with engine code letters BLR (EU4): – the three way main catalytic converter is fitted –instead of the NOx-storage catalytic converters, – no exhaust gas temperature sender is fitted, – a post-catalytic converter probe is fitted instead of the NOx sensor.Post-catalytic converter probe (jump probe) Exhaust gas temperature senderThere are two post-catalytic probes (jump probes) behind the pre-catalytic converters. They monitor the efficency of the pre-catalytic Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted For vehicles with engine code letters converters. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with unite respect toto the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� BLY (EU2): Afterwards the two exhaust strands – no pre-catalytic converters are one exhaust strand. At this location an fitted with pre-catalytic converter exhaust gas temperature sender is placed. probes, After the temperature sender, the system – the three way main catalytic branches out in two strands. One NOx-storage converter is fitted instead of the catalytic converter is situated in each strand. NOx-storage catalytic converters, – a pre-catalytic converter probe is The storage catalytic converters store the fitted instead of the exhaust gas nitrogen oxides (NOx) in the lean mode temperature sender, intermediately, whereby the NOxsensor – a post-catalytic converter probe monitors the saturation degree and releases (jump probe ) is fitted instead of the regeneration of the storage catalytic the NOxsensor. converters.GB33Exhaust systemExhaust systemThe further increasing demands on the exhaust systems, due to the decreased emission limit values, require an innovative concept, which is adapted in particular to the FSI procedure. The 2.0 l/110 KW FSI engine (EU4) has for each exhaust strand a pre-catalytic converter with a pre- and a post- catalytic converter probe.Note: The illustration shows the simplified representation only with one exhaust strand.Stratified charge modePre-catalytic converter probePre-catalytic converterPost-catalytic converter probeNOx sensor control unit J583 The NOx sensor control unit is located at the vehicle underfloor near the NOx sensor. It prepares the sensor signals and transmits the information via the CAN databus drive to the engine control unit. The fast data transmission enables the engine control unit to determine more effectively the nitrogen oxide saturation of the storage and to introduce a regeneration.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�34GBExhaust gas after treatment system For a lean mixture composition, there is a lot of remaining oxygen in the exhaust gas. The conversion rate of NOx drops when the CO and HC concentrations in the exhaust gas are too low. The NOx storage catalytic converter is used for the reduction of the increased NOx share in lean mode, (stratified charge mode).Motronic control unit J220 (engine control unit)NOx sensor control unitCO– Carbon monoxideNOx – Nitrogen oxygen HC Exhaust gas temperature sender G235 NOx sensor H2O CO2 O2 N2 – Carbon dioxide – – – – Water Carbon dioxide Oxygen NitrogenProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP55_44NOx storage catalytic converter The NOxstorage catalytic converter corresponds in its structure to the three-way catalytic converter. The intermediate layer (wash coat) is however additionally covered with barium oxide BaO. This enables nitrogen oxides to be stored intermediately at temperatures between 250 and 500 °C through nitrate formation.NOx storage catalytic converterApart from the desired nitrate formation, the sulphur, which is always contained in the fuel, is also deposited. The storage capacity is limited. The saturation is communicated to the engine control unit by means of the NOx sensor. The engine management introduces appropriate measures for the regeneration of the NOxstorage catalytic converter.35GBExhaust systemRegeneration of the NOxstorage catalytic converterThe regeneration phases are actuated by the engine control unit. They dissolve away the nitrogen oxides and the sulphur. While doing so, the nitrogen oxides are converted into innocuous nitrogen N2 and sulphur into sulphur dioxide.For saturation with nitrogen oxides The regeneration is performed as soon as the nitrogen oxide concentration in the NOx storage catalytic converter exceeds the fixed value in the engine control unit. The engine control unit arranges the switchover from the stratified charge mode into the homogeneous mode. This causes a temperature increase of the NOx storage catalytic converter, through which the nitrate formations become unstable. The intermediately stored nitrates disintegrate when the surrounding conditions are reduced. Finally, the nitrogen oxides are converted into harmless nitrogen. The storage is emptied and the circulation begins again.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�approx. 2 secondsStratified charge mode60–90 secondsHomogeneous mode λ 1Stratified charge modeSP55_7636GBFor saturation with sulphur The regeneration is performed in separate phases, as the barium sulfate formed from the barium oxide is chemically more stable and does not disintegrate during the transformation of nitrogen oxides. The barium sulfate occupies also storage locations, through which the saturation of the NOxstorage catalytic converter of nitrogen oxides is achieved in increasingly shorter intervals. As soon as a fixed limit value between two distances is not reached, the engine management reacts with the following measures: – It switches for approx. two minutes from stratified charge mode into homogeneous mode – and adjusts the igntion timing point towards “late”, in order to increase the operating temperature of the NOx storage catalytic converter to above 650 °C. At the same time the barium sulfate is changed back into barium oxide and the sulphur, which is thereby released, converts into sulphur dioxide SO2. In case of sulphuric-poor fuels, the desulphurisation interval is extended accordingly, while high sulphuric fuels introduce more frequent regeneration phases. Note: Driving with high speed and load leads automatically to desulphurisation.TDCapprox. 2 minutesStratified charge modeTDCHomogeneous modeIgnition timing point “late”Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�TDCStratified charge modeSP55_77GB37Exhaust systemSenderExhaust gas temperature sender G235 The exhaust gas temperature sender is located directly in front of the NOx storage catalytic converter. With the help of the exhaust gas temperature sender, the operating range of the NOx storage catalytic converter is monitored and actuated in regards to the temperature, in order to ensure an optimal NOx conversion. In addition, the exhaust gas temperature sender serves for the thermal diagnosis of the pre-catalytic converters and thus for the protection of the components in the exhaust strand. The sender transmits the exhaust gas temperature to the engine control unit, from which the temperature in the NOx storage catalytic converter is calculated. The engine management needs this information, – in order to be able to switch into the stratified charge mode, as the nitrogen oxides in the NOxstorage catalytic converter can only be stored between 250 and 500 °C and – in order to release the sulphur deposits from the NOx storage catalytic converter. That is possible only at catalytic converter temperatures above 650 °C and a rich mixture. This is achieved by switching over to the homogeneous mode and ignition angle cancelling.Connection pinHousing with holesBase materialSP55_79Sensor element in ultra-thin platinumAl2O3 substratumIsolationNOx sensor G295 The NOx sensor is located directly behind the NOx storage catalytic converter. The function principle of the NOx sensor ressembles the one of the wide band lambda probe. In the O2 pump cell, the oxygen content is adapted to the constant stoichiometric value (14.7 kg of air: 1 kg fuel) and the lambda value is measured via the pump current.Platinum electrode NOx active elektrode O2 selective elektrode YS-ZrO2O2 measuring cell O2 pump cellSubsequently, the gas flow penetrates via a diffusion barrier into the O2measuring cell, SP55_78 which splits up the nitrogen oxides by means of the reducing electrodes into oxygen (O2) and nitrogen (N2). The NOx concentration is Heater Protected by copyright.pump Copying for private or commercial purposes, in part or in whole, is not permitted Diffusion barrier determined via the oxygen current. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�38GBExhaust gas recirculationThe exhaust gas recirculation accelerates the heating up of the engine to the operating temperature. The exhaust gas, which is supplied once again to the combustion chamber, serves for decreasing the combustion peak temperature as well as for reducing the nitrogen oxide formation. The 2.0-ltr. FSI engine has an outer exhaust gas recirculation. The extraction of the exhaust gas is performed via a connecting pipe at the pre-catalytic converter.Exhaust gas recirculation valve N18The exhaust gas quantity then flows through the exhaust gas recirculation valve (EGR) with the accurate quantity calculated by the engine control unit. The position of the exhaust throttle valve is set by a d.c. motor and is monitored by means of a potentiometer. This enables the feedback to the engine control unit. The exhaust gas recirculation valve is self diagnostic. The housing of the exhaust gas recirculation valve is cooled and integrated into the coolant circuit.Connection for coolantConnecting pipe to pre-catalytic converterPre-catalytic converterConnecting pipe to intake manifoldSP55_80The exhaust gas recirculation valve N18 EGR is conceptualized as a module and consists of the following parts: – an exhaust gas throttle valve – an electric motor with a potentiometer for exhaust gas recirculation G212 The exhaust gas recirculation is performed in the homogeneous as well as the stratified charge mode at an average load up to approx. 4000 rpm. No exhaust gas recirculation occurs in idle. Note: After replacing the exhaust gas recirculation valve EGR and/or the engine control unit, an adaptation must be carried out via the function “Basic setting”.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB39Engine mechanical componentsPart II – 1.6-ltr. FSI engineEngine highlights – Engine cover with air filter and warm air control – Plastic intake manifold top part – camshaft drive via a timing chain – continuous camshaft adjustment – Oil cooler – regulated Duocentric oil pump – Two-circuit cooling system – Cross-flow cooling in cylinder head – Crankcase fresh air supply and ventilation – Gasoline direct injection with double injection – Engine control unit with integrated ambient pressure sender – Intake air temperature sender in the engine cover – Fuel system regulated as needed – Signal spark ignition coil – Integrated radiator and fan controlProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP55_18Technical highlights100200Engine code letters Design Displacement Bore Stroke Compression ratio Valves per cylinder Firing order max. power output max. torque Engine management Fuel Emission standard40BLF 4-cylinder inline engine 1598 cm3 76,5 mm 86,9 mm 12,0 : 1P (kW) M (Nm) 90 1808016070140601204 1–3–4–2 85 kW at 6000 rpm 155 Nm at 4000 rpm Motronic MED 9.5.10 Petrol 98 (95) RON EU450100408030602040102001000200030004000500060007000n (min –1 )M = Torque n = Engine speed P = Power outputSP55_101GBChain driveFor the 1.6-ltr./85 kW FSI engine, a noise optimized timing chain is used for the drive of the camshafts. It is tightened hydraulically with a tensioning rail. When developing the timing chain, the following targets were pursued: – Maintenance-free operation – Reduction of the noise level (in comparison to the previously used timing belt drive) – Low system costs The targets were achieved through the use of a tooth chain with 8 mm gaps in the control drive. This chain offers an optimal compromise regarding • • • • Installation space, Load capacity, System complexity and Noise behaviour.A conventional sleeve chain is used for the drive of the oil pump, because of the smaller demands.Inlet camshaftExhaust camshaft Timing chainChain sprocketSliding railCrankshaft Hydraulic tensioning rail Crankshaft journal with 2 chain sprocketsOil pump drive chainChain tensioner for oil pump drive chainProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept anySP55_103 liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Oil pump Oil pump chain sprocketGB41Engine mechanical componentsCamshaft adjustmentThe 1.6l/85 kW FSI engine is available with a continuous inlet camshaft adjustment. The adjustment is performed dependent on load and speed via a camshaft adjuster directly at the inlet camshaft. The camshaft adjustment leads to • a very good internal exhaust gas recirculation, which lowers the combustion temperature and reduces the nitrogen oxide emissions and • improves the torque course.Inlet camshaft timing adjustment valve N205Note: The central fixing screw of the camshaft adjuster has a left-hand thread.SP55_96Camshaft adjuster Central fixing screw20°Camshaft adjuster The camshaft adjuster is screwed on the control drive side onto the inlet camshaft. The adjustment range is maximum 40° Protected by copyright. for private or commercial purposes, crankshaft and/or 20° Copying camshaft angle from the in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability basic setting towards “Early”. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�External rotorInternal rotorSP55_97Note: The principle of the camshaft adjustment is similar to the camshaft adjustment of the 2.0-ltr. FSI engine. In contrast to the 2.0-ltr. FSI engine, it is not the external rotor which is adjusted, but the internal rotor.42GBSealing the timing caseThe timing case compared to the cylinder head and the cylinder block is sealed with a rubber metal gasket. A fluid gasket is used between the timing case and the oil pan.Oil filter housingTransition area of the engine oilSP55_84Rubber metal gasket Cross-sectionProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Rubber Metal with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP55_85Oil filter housing The oil filter housing is integrated into the timing case. Therefore the sealing surface between the cylinder block and the oil filter housing does no longer exist!Transition area of the engine oil A rubber metal gasket is used for the sealing of the oil duct between the cylinder block and the control unit.GB43Engine mechanical componentsOil pumpAs an oil pump, a regulated Duocentric oil pump is used for the first time. With which the oil pressure is regulated nearly over the entire speed range to approx. 0.35 MPa. The regulation is performed by a control ring and a control spring. This can result in the following advantages: – The drive power output of the oil pump is decreased by 30 %. – The oil wear is reduced, because less oil is circulating. – The oil foaming in the oil pump is minimized, because the oil pressure remains nearly constant in the entire speed range.External rotorSP55_94Pressure regulator valveHousingChain sprocketControl ring Control spring Oil intake pipe Drive shaft with internal rotor Housing coverProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�CrankshaftSleeve chainSpringDrive of the oil pump The oil pump is screwed on at the bottom of the cylinder block and is driven via a maintenance-free chain drive by the crankshaft. The chain is tightend by means of a steel spring at the chain tensioner.Spring-tensioned chain tensionerSP55_95Oil pump chain sprocket 44GBPrinciple of the oil delivery The internal rotor is fitted onto the drive shaft and drives the external rotor. A space enlargement on the suction side occurs during the rotary movement due to the different pivots for the interior and external rotor. The oil is suctioned and tranported to the pressure side. On the pressure side, the area between the teeth becomes smaller and the oil is injected into the oil circulation system. Control of the oil pressure For the regulated Duocentric oil pump, the oil pressure of 0.35 MPa is regulated via the oil delivery quantity.ide ion s Suct ide ery s DelivOil pressure below 0.35 MPaExternal rotorin the oil The control spring presses the control ring circulation against the oil pressure (arrows). The twisting of the control ring offsets the pivot of the external rotor and a space enlargement occurs between the internal and external rotor. This results in more oil being transported from the suction to the pressure side and injected into the oil circulation. The oil pressure increases also with the quantity of oil. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedInternal rotorControl springunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP55_100Control ring from the oil panDelivide ion s Suct ide ery sOil pressure above 0.35 MPa The oil pressure (arrow ) presses the control ring against the control spring. The pivot of the external rotor returns in the direction home position. This results in a space reduction between the internal and external rotor. This results in more oil being transported from the suction to the pressure side and injected into the oil circulation. The oil pressure decreases also with the quantity of oil.in the oil circulationExternal rotorInternal rotorControl springSP55_104Control ringfrom the oil panGB45Engine mechanical componentsEngine coverThe following is integrated in the engine cover: – Air guide for throttle valve module – Warm air control – Damping of intake noises – Air filter – Intake air temperature sender 2 G299Engine cover Filter element Intake air temperature sender 2 G299Thermostat coverThermostat warm air control Air filter housingfor crankcase fresh air supply at camshaft housingfoldedControl flap for intake air preheatingSP55_102Air outlet for throttle valve module J338Air inletAir inlet for warm airBores used for damping the intake noisesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�46GBIntake manifold - top partThe intake manifold – top part is made out of plastic. It has the following advantages: – Weight reduction – Flow improvement through smooth suction walls In the intake manifold – top part there is a vacuum storage, which ensures that the intake manifold flaps are also actuated at a low vacuum in the intake manifold - bottom part.Throttle valve module J338Plastic intake manifold with vacuum storageto vacuum positioning element for intake manifold flaps in intake manifold - bottom partto exhaust gas recirculation valve N18Intake manifold flap valve N316Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�from diaphragm valve for crankcase ventilation Intake manifold pressure sender G71 and intake air temperature sender G42SP55_83to pressure sensor for brake servo pressure sensor G294Activated charcoal filter system solenoid valve 1 N80to activated charcoal reservoirGB47CoolingTwo-circuit cooling systemThe cooling system in the engine is divided into two oil circuits. One third of the coolant in the engine flows to the cylinders and two thirds to the combustion chambers in the cylinder head.from cylinder head Cross-flow cooling in the cylinder head, coolant temperature 87 °C Longitudinal cooling in the cylinder head, coolant temperature 105 °Cfrom radiator to coolerfrom coolerThermostat housingSP55_90Position of the thermostats up to 87 °C Both thermostats are closed, through this the engine is warmed up more rapidly. The coolant flows through the following Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability components:with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Thermostat 1– – – – – – –Coolant pump Cylinder head Thermostat housing Heat exchanger Oil cooler Exhaust gas recirculation valve Expansion reservoirThermostat 2SP55_9148GBPosition of the thermostats from 87 °C up 105 °C The thermostat 1 is opened and the thermostat 2 is closed. This regulates the temperature in the cylinder head to 87 °C and the temperature is further increased in the cylinder block. The coolant flows through the following components: – – – – – – – – Coolant pump Cylinder head Thermostat housing Heat exchanger Oil cooler Exhaust gas recirculation valve Expansion reservoir CoolerThermostat 1Thermostat 2SP55_92Protected by copyright. Position of the themostats above 105 Copying °C for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Both thermostats are opened. This regu