TECHNICAL DOCUMENTATION
SSP 058 Chassis and electromechanical power assisted steering

This PDF is currently unavailable.
Read document text
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The new chassis was designed with the aim of achieving the optimal combination of highest driving convenience and outstanding driving characteristics. The rack and pinion type steering system with new electromechanical steering assistance contributes to this in addition to the new axles. The effective and reliable brake system, which distinguishes itself through fast response and exact proportioning of the braking force, offers a high safety level. For the first time ŠkodaOctavia is offered with the system TPM*, which monitors the inflation pressure in the individual tyres.*Tyre Pressure Monitoring2GBContentsPart I – ChassisIntroduction Chassis Front axle Front axle - Overview Rear axle Rear axle - Overview Brake system Brake system Hydraulic control units Antilock braking system ABS/ESP Brake pressure sender 1 G201 Brake assignment 4 4 5 5 10 10 16 16 18 19 19 21Part II – Electromechanical power-assisted steeringElectromechanical power-assisted steering Introduction Steering column System overview System overview Function Performance maps and characteristics Steering procedure Electronics of power-assisted steering Steering torque sender G269 Steering angle sender G85 Electromechanical power-assisted steering motor V187 Rotor speed sender Vehicle speed Engine speed sender G28 Steering aid control unit J500 Electromechanical power-assisted steering warning light K161Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Function diagram unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Function diagram22 22 24 26 26 27 27 28 30 30 31 34 35 35 35 36 37 38 38 39ServiceOCTAVIA IIII OCTAVIAXXXXXXXXXXXXXXXX XXXXXXXNotesServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXXXXXXXX XXXXXXXS e r v i c eYou will find notes on inspection and maintenance, setting and repair instructions in the Workshop Manual.XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXGB3IntroductionChassisThe chassis of ŠkodaOctavia once again sets the yardstick in its category. For example the use of suspension struts of the front axle with an optimized dynamic suspension characteristic. Or the introduction of the new multi-arm axle, in order to achieve a good driving dynamics and a good suspension convenience. The electromechanical power-assisted steering assists the driveability in a good manner and obtains a pleasant steering sensation. It adapts the steering forces harmoniously in line with the vehicle speed. The ŠkodaOctavia can be equipped with a standard chassis, sport chassis or rough road chassis. The chassis differ through the suspensions, setting of the shock absorbers, dimension of the anti-roll bars and the auxiliary suspensions, which also function as stop buffers. The sport chassis is positioned 15 mm lower in contrast to the agile and convenienceoriented standard chassis. The vehicle structure of the rough road chassis is positioned 25 mm higher in contrast to the standard chassis.SP58_01Technical highlights –Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�– – – –Stationary accelerator pedal with contactless accelerator pedal position senders Optimized suspension strut axle according to the McPherson principle at the front axle Anti-roll bar tie via coupling rods to the suspension struts Electromechanical power-assisted steering Multi-arm rear axle–– – – –Electronic stability program of MK60 system of the company Continental Teves, optional Tyre pressure inspection display, optional Brake assistance Separately adjustable track and camber on the rear axle Wheel rim sizes: 15˝, 16˝ or 17˝4GBFront axleFront axle - OverviewThe kinematically proven independent McPherson front wheel suspension was used for the front-wheel-drive of the ŠkodaOctavia. It is equipped on both sides with a track control arm and a wheel-guiding suspension strut. The front axle offers optimal convenience for very good driving dynamics. The positioning of the front axle in the aluminum assembly carrier is new. Thus, the improvement of kinematic and elastokinematic characteristics was achieved through simultaneous reduction of the axle weight.Wheel-bearing housingThe outstanding characteristics of this type of axle could still be improved through a careful development. The result is a considerably improved agility of the chassis, the steering accuracy and thus a noticeable improvement of the driving convenience. The lateral stability of the vehicle front was also increased, which provides for an exact and safe curve guidance of the vehicle.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Power-assisted steering Protected by copyright. Copying for private or in whole, gear is not permitted Track rod or commercial purposes, in partSuspension strutConsoleAnti-roll bar Wheel bearingTrack control armAssembly carrier Pendulum support Coupling rodSP58_02GB5Front axleAssembly carrier The three-part aluminum assembly carrier serves as support of the track control arm, the anti-roll bar and the power-assisted steering gear. A high rigidity and a good driving dynamics is obtained through the 6-pin rigid screwed connection.Assembly carrier Left consoleRight consoleSP58_03Track control arm The track control arm represents the lower connection between body and wheel-bearing housing. They are engine dependent and made out of grey cast iron or sheet metal and connected via rubber metal bearings with the consoles of the assembly carrier.Power-assisted steering gear Left consoleProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Assembly carrierTrack control arm 6SP58_04GBAnti-roll bar The anti-roll bar (pipe) is fastened via two coupling rods to the suspension struts. The suspension strut is firmly connected to the wheel-bearing housing. The advantage in relation to the "old" Octavia is that the force works directly between the suspension strut and the anti-roll bar. On the "old" Octavia the forces of the anti-roll bar worked via a suspension arm on the wheels. A higher effect of the anti-roll bar was achieved through the new tie. The anti-roll bar could be manufactured from pipe, which gives a weight reduction.Suspension strutClamp with rubber bearing Anti-roll barCoupling rodProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_05Assembly carrier increased relative rotary movementThe anti-roll bar is fastened to two rubber bearings via clamps at the assembly carrier. There is such a large pretension in the rubber bearings that it is not possible for the anti-roll bar to turn. The relative rotary movement between the anti-roll bar and the clamp is eliminated by the deformation of the rubber bearing.Anti-roll barSP58_06Rubber bearing ClampGB7Front axleWheel-bearing housing Depending upon engine type, the wheelbearing housing is used with: • integrated brake carrier or • screwed on brake carrier. The wheel-bearing housing is firmly connected with the suspension strut via a clamping joint. In the lower area, the wheel-bearing housing is bolted to the track control arm by a steering joint. Wheel- bearing hous ing with integrat ed brake c arrier (brak e FS-III ) This version is intended for lower engine types. The brake carrier is an integral part of the wheel-bearing housing. Thus the brake caliper is screwed directly to the wheelbearing housing. The brake pads are supported at the arms of the wheel-bearing housing. The arms absorb the brake forces. Wheel- bearing hous ing with s c rewed on brake carrier (brak e FN3 ) This version is intended for higher engine types. On this version the brake carrier is an independant part and fastened with two screws to the wheel-bearing housing. The brake caliper and the brake carrier are screwed with each other. The brake pads are supported on the brake carrier. The braking forces are transferred via the two screws into the wheel-bearing housing and absorbed.Suspension strut Clamping joint Wheel-bearing housingWheel hub with wheel bearingSP58_07Brake caliperSteering jointWheel-bearing housing Brake carrierBrake caliper Screw connectionSP58_08Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Wheel hub with wheel bearingWheel hub with wheel bearing form a compact wheel bearing unit. A double-row angular ball bearing of the 3rd generation was used. This wheel bearing unit is screwed with four screws to the wheel bearing housing. The advantage of this wheel bearing unit is an easy removal and installation.SP58_098GBSuspension strut Suspension struts with a combination of two springs are used for the suspension of the vehicle. The main element is the helical spring, the side element is the auxiliary spring. It serves at the same time as upper stop buffer. The helical spring has a linear spring characteristic and is made out of high-tensile steel. The spring is pulled in at the ends. The auxiliary spring has a progressive spring characteristic and consists of foam polyurethane. The movements of the body and the wheels are absorbed by a hydraulic shock absorber when driving over a bumpy road.Suspension strut bearing Auxiliary spring (stop buffer)Helical springShock absorberSP58_10Suspension strut bearing The suspension strut bearing is a rubber metal bearing. The spring force is introduced separately into the body by decoupling the spring and shock absorber tie to the body. Thus a pretension of the shock absorber bearing is prevented. This influences positively the roll off convenience and reduces the transmission of the roll off noises to the body. The suspension strut bearing has a soft characteristic in the driving direction. Thus the driving convenience and the vehicle acoustics is improved. In transverse direction it is designed rigidily. This measure influences positively the driving dynamics and the response of the steering.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_11GB9Rear axleRear axle - OverviewThe rear axle was completely newly developed. For the first time a multi-arm axle is used in the new ŠkodaOctavia. It enables excellent driving characteristics and more stability in extreme situations. The multi-arm rear axle consists of four-arm semi axles • Top suspension arm, • Bottom suspension arm, • Track rod (suspension arm) and • Trailing arm. This design solution enables an ideal response to the longitudinal and transverse forces. The transverse dynamics is secured by three suspension arms • Top suspension arm, • Bottom suspension arm and • Track rod (suspension arm). The carefully defined and co-ordinated position enables an accurate setting of the necessary work modes.Helical springTop suspension armAnti-roll barShock absorber Wheel bearingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Bracket Track rod (suspension arm) Assembly carrier Wheel-bearing housing Bottom suspension arm Trailing armSP58_1210GBAssembly carrier The assembly carrier is a welded component out of steel. It is rigidily screwed to the body.SP58_13Wheel-bearing housingWheel bearingThe wheel bearing housing is a forged The wheel bearing is a double-row angular component out of steel with shaped axle studby copyright. ballCopying bearing of or the 2nd purposes, generation. Protected for private commercial in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability for the support of the wheel hub with wheel Wheel hub and wheel bearing form a AUTO A. S.� with respect to the correctness of information in this document. Copyright by ŠKODA bearing. compact unit. The wheel hub with wheel bearing is positioned on the axle stud of the wheelbearing housing. A screw secures the wheel hub with the wheel bearing. The tightening of the screw ensures the optimal necessity of the pretension.Axle stud Wheel hub with wheel bearingScrew Wheel-bearing housingSP58_14GB11Rear axleTrailing arm The trailing arm is mounted on the side of the body with a rubber metal bearing in a steel plate bracket. The bracket is rigidily screwed to the body. The large volume rubber metal bearing contributes considerably to the good roll off convenience. The trailing arm is rigidily screwed to the wheel-bearing housing. In upright direction it is resistant to bending and thereby supports the braking and starting off torques.BracketProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_15Wheel-bearing housing Rubber metal bearing Trailing armNote: The rubber metal bearing is in the installation position – see Workshop Manual. The screwed connection of the trailing arm to the bracket is performed before the screwed connection of the bracket to the body. Observe the position of the parts to each other – see Workshop Manual.12GBBottom suspension arm The body rests on the bottom suspension arms above the helical springs. The bottom suspension arm is a moulded steel part. For protection against stones, the bottom suspension arm on the rough road chassis is provided with an additional plastic cover. The coupling rod for the rear left vehicle level sender G76 is fastened to the left bottom suspension arm. The fastening of the bottom suspension arms to the assembly carrier is performed with eccentric bolts, eccentric washers and nuts. The track is adjusted by turning the eccentric bolts.Eccentric washer with lug NutEccentric boltAssembly carrierAnti-roll barTrack rod Bottom suspension armSP58_16Top suspension arm The top suspension arm establishes the connection between assembly carrier and wheel-bearing housing. The suspension arm has a T-shape cross-section and absorbs particularly the side forces. The fastening of the top suspension arms to the assembly carrier is performed with eccentric bolts, eccentric washers and nuts. The track is adjusted by turning the eccentric bolts.Nut Eccentric washer with lug Eccentric bolt Assembly carrier Top suspension armProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_17GB13Rear axleTrack rod The track rod is made out of steel plate and serves as support of the transverse forces.Assembly carrierTrack rod Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_18Anti-roll bar Anti-roll bars with different dimensions are used for the standard, sport and rough road chassis. For reasons of weight the anti-roll bars are manufactured from pipe. The anti-roll bar is fastened to the assembly carrier in the rubber bearings with clamps as on the front axle. The anti-roll bar is screwed to the wheelbearing on both sides by means of the coupling rod above the trailing arm. The coupling rods are made out of steel. They have a ball joint on the side of the wheelbearing, a rubber bearing on the side of the anti-roll bar.Assembly carrierAnti-roll bar Ball jointClamp with rubber bearingSP58_19Coupling rod Rubber bearing 14GBHelical spring A cylindrical spring out of high-tensile steel and pulled-in ends with linear spring characteristic is used. The mounting at the body and bottom suspension arm is performed through spring seats.Top spring seatHelical springBottom spring seat Bottom suspension armSP58_20Note: The helical spring is fitted in position above the bottom spring seat, see Workshop Manual.Shock absorber bushingShock absorber The two-pipe pressurized shock absorbers are mounted on the wheel-bearing housings. Thus an optimal ratio of the wheel path to the shock absorber path is Protected possible and Copying a large by copyright. for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability through-loading width iswith guaranteed. respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� In comparison to the previous vehicle, the shock absorber internal pressure was reduced through larger dimensions of the shock absorber pipe and piston. This results in an enhancement.Shock absorberSP58_21GB15Brake systemBrake systemWell-designed brakes, which bring the vehicle in time and reliably to a halt, are a substantial component of a perfect chassis. Due to the constantly increasing demands on vehicle dynamics and active safety, the brake systems were further developped on ŠkodaOctavia.AB S In all equipment versions an ABS with diagonally distributed dual circuit brake system with brake booster is used.SP58_22B rake boosterThe brake system is equipped with a brake booster with the function "Dual-Rate". This function provides for the increase of the braking force reinforcement during operation of the brake pedal in critical situations.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�B r akesIn order to guarantee a sufficient braking effect with a fast start-off time, size and cooling of the brake disc as well as the brake calipers are of importance. The vehicles ŠkodaOctavia are equipped with brakes of the types FN and FS, which offer an optimal brake output. The materials used for the brake pads are environmentally friendly. Disc brakes at front and rear axle are used for all engine types.16GBBrake booster A 10“brake booster of the company ContiTeves is used in ŠkodaOctavia. The "dual rate characteristic" is a substantial innovation on this brake booster. This means that the brake booster functions according to a two-stage characteristic. A characteristic with progressive course according to a so-called "dual rate characteristic" is implemented by a correspondingly altered interior structure of the brake booster. Brake boosters, which implement the "dual rate characteristic", are called brake boosters with mechanical brake assistant (MBA). During a strong brake pedal actuation this results in higher brake pressures as for conventional brake boosters (without MBA). This ensures a good balance.Brake booster Pressure rodSP58_23For safety aspects an optimized pressure rod is fitted in the brake booster, which fulfills the requirements of the crash tests.Note: The right-hand drive vehicles receive a tandem brake booster of the dimension 7/8“.Reinforcement area"Dual-Rate characteristic" When operating the brake pedal, the brake pressure in the brake booster does not rise linear over the entire area. Starting from a certain pedal force (in the diagram point A), the brake pressure increases faster than with the conventional brake booster.Brake pressureAPedal forceProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Brake booster with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_24with the function"Dual-Rate" conventional brake boosterGB17Brake systemHydraulic control unitsHydraulic control unit MK70 The hydraulic control unit consists of: – – Hydraulic unit with hydraulic pump and electric motor Control unitHydraulic unit with hydraulic pump Electric motor for hydraulic pumpIn ŠkodaOctavia is fitted the hydraulic controlunit MK70 of the company Conti-Teves. It distinguishes itself by the following technical highlights: – – – – Antilock braking system (ABS) with electronic braking force distribution (EBV) Engine towing torque control (MSR) Traction control system (ASR) is realised by the engine control unit; this means without active brake interferenceControl unitProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_25Hydraulic control unit MK60 Optionally the hydraulic control unit MK60 with integrated pressure sensor (brake pressure sender 1 G201) is used in ŠkodaOctavia. In comparison to the hydraulic control unit MK70, it has in addition the following technical highlights: – – – – – electronic stability program (ESP) hydraulic brake assistant (HBA) traction control system (TCS) electronic differential lock (EDL) uphill-start off-assist (HHC) – only as special equipmentHydraulic unit with hydraulic pumpElectric motor for hydraulic pumpSP58_26Note: A hydraulic control unit MK70 is used as an ABS system. As it includes only the ABS function (4 inlet and 4 outlet valves), it is smaller and easier in relation to the hydraulic control unit MK60.Control unit18GBAntilock braking system ABS/ESPHydraulic control unit MK60 of Conti-Teves The hydraulic control unit MK60 for the Škoda Octavia has the following main innovations: – active wheel speed sensors (without forwards and reverse detection) – combined yaw rate sender G202 and lateral acceleration sender G200 (under the front passenger seat); these combined senders transmit the information via the separate CAN bus––Integration of the brake pressure sender 1 G201 into the hydraulic unit; the sender was previously screwed into the tandem master brake cylinder new ESP and TCS warning light K155SP58_55SP58_53Brake pressure sender 1 G201Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_56Spring contacts Brake pressure sender 1 G201GB19Brake systemTask The brake pressure sender 1 G201 measures the brake pressure introduced by the driver via the brake pedal. In order to ensure a higher safety, the sender supplies two pressure signals which are independent of each other. These are transmitted simultaneously as two contra-rate voltages. The ABS control unit compares these permanently with each other.SP58_58 SP58_57SP58_591 – Measuring chamber 2 – piezo resistant* thick film measuring element It consists of: • flexible thick film diaphragm and • piezo resistant measuring bridge with the Piezo bridge elements 3 – Sensor electronics and signal reinforcement 4 – Spring contacts Two contacts serve the voltage supply, the two others are used for the two independent pressure signals.5 – piezo-resistant measuring bridge 6 – flexible thick film diaphragm 7 – Piezo bridge element within the piezoresistant measuring bridge p – Brake fluid pressureStructure The sender operates according to the piezoresistant method. Thereby the change in the conductivity of materials is used through structure deformation. Four piezo-resistant Piezo bridge elements 7, which are interconnected to a piezo-resistant measuring bridge 5, are fitted on a flexible thick film diaphragm 6. The Piezo bridge elements are resistors out of semiconductor material. The function mode is comparable to the one of the wires.Working mode A pressure increase of the brake fluid changes the length of the flexible thick filmdiaphragm 6 and the piezo-resistant measuring bridge 5 connected to it. By means of this length modificaton, forces are applied to the 5 Piezo bridge elements 7 contained in the piezo-resistant measuring bridge, which change the charge distribution within the Piezo bridge elements 7. The electrical characteristics of the Piezo bridge elements 7 change with the modified charge distribution. These are proportional to the brake fluid pressure p and are passed on as a reinforced sensor signal to the ABS control unit J104.Effects of signal failure If the signal of the brake pressure sender fails, the ESP function is reduced to the function ABS and EBV (electronic braking force distribution).*Piezo-resistant effect Change of purposes, the specific resistance of metals or semi-conductors in case Protected by copyright. Copying for = private or commercial in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability of mechanical stress. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB20Brake assignmentEngineFront brakeRear brake Ø 255 x 10 mm C381.4 ltr./55 kW 1.6 ltr./75 kW 1.9 ltr./77 kW with front-wheel-drive and with manual gearboxØ 280 x 22 mm FS-IIISP58_49Ø 260 x 12 mm CII41SP58_271.6 ltr./85 kWSP58_291.9 ltr./77 kW with four-wheel drive and with manual gearbox as well as with front-wheeldrive and with automatic gearbox DSGØ 288 x 25 mm FN3Ø 260 x 12 mm CII412.0 ltr./100 kW 2.0 ltr./103 kW 2.0 ltr./110 kWSP58_28SP58_29Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB21Electromechanical power-assisted steeringIntroductionIt is a prime advantage that in contrast to the hydraulic steering systems a hydraulic system is not necessary for the electromechanical power-assisted steering with double pinions (steering pinion and drive pinion). This results in further advantages, such as: – hydraulic components, such as servo oil pump, hoses, hydraulic oil reservoir, not applicable hydraulic oil not applicable structure chamber not required low noise development energy saving A clear energy saving is achieved. In contrast to the hydraulic steering, which requires a permanent volume flow, the electromechanical power-assisted steering only uses energy when steering. The fuel consumption is reduced by the power absorption capacity, which fulfils this demand. The driver has an optimal driving sensation in each situation, through – a good straight course (the resetting of the steering in the straightahead position is actively assisted by the electromechanical power-assisted steering), a direct, but soft response to steering commands, no unpleasant steering reactions on bumpy road.– – – –The steering-assisted components are seated and effective directly on the power-assisted steering gear.– –Note: The fuel saving amounts up to 0.2 litres on 100 kilometers. The steering assistance takes place also when towing, if the following requirements are fulfilled:Steering wheelSteering columnCardan joint Electromechanical powerassisted steering motor V187• Towing speed more than 7 km/h Steering torque • Ignition on sender G269 • Battery sufficiently charged Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_33Power-assisted steering gear Steering aid control unit J50022GBOverview of individual partsSteering pinionSteering torque sender G269Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_34Steering aid control unit J500Electromechanical power-assisted steering motor V187Worm gearDrive pinionGB23Electromechanical power-assisted steeringSteering columnThe height and length adjustment of the steering column is mechanical. It can be adjusted for optimal adjustment to the needs of the driver in vertical direction by 50 mm and in longitudinal direction by 60 mm. The clamping of the steering column is performed by a plate package with ten steel plates. Five plates mounted in horizontal position enable the length adjustment. The other five plates are mounted in the vertical direction and enable the height adjustment. The connection of the steering column to the central pipe/dash panel is performed via a holder out of aluminium cast iron.Plate package for length adjustmentPlate package for Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability height adjustmentwith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_6224GBFunction principle of clamping The clamping is produced by two rollers, which run up a ramp during the fixing procedure. This compresses the plate package above the pressure plate. The adjustment is stepless, because the serrations in the clamping mechanism have been eliminated, i.e., one can lock the steering column problem-free in each position.Plate package releasedPressure plate Plates for height adjustmentRollerRamp Plates for length adjustmentSP58_63Plate package clampedPressure platePlates for height adjustmentProtected by copyright. Copying for private or commercial purposes, in partRoller or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�RampPlates for length adjustmentSP58_64GB25System overviewSystem overviewABS control unit J104 Engine speed sender G28Speed sensor G44 – G47 (vehicle speed signal)Motronic control unit J220 Data bus diagnostic interface J533 (Gateway)CAN DriveSteering column electronics control unit J527Dash panel insert control unit J285Steering angle sender G85Electromechanical power-assisted steering warning light K161aid control J500 Protected by copyright. Copying forSteering private or commercial purposes, unit in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_35Steering torque sender G269Electromechanical powerassisted steering motor V18726GBFunctionPerformance maps and characteristicsThe control of the steering assistance is performed by a performance map in the permanent program memory of the steering aid control unit J500. At present on the ŠkodaOctavia seven different performance maps are used. Depending on demand (e.g. vehicle weight) a performance map is activated at the factory. For the customer service the performance map can also be activated using the vehicle diagnosis, measuring and information system VAS 5051. This is necessary e.g. when changing the complete electromechanical power-assisted steering.v = 0 km/h Supporting torque [Nm]v = 15km/h v = 50 km/hv = 100 km/h v = 250 km/hSP58_36Steering torque [Nm]Selected as examples are a performance map for a heavy vehicle and a performance map for a light vehicle of the 7 existing performance maps from ŠkodaOctavia.Characteristic for heavy vehicle Characteristic for light vehicleEach performance map contains five different characteristics for different vehicle speeds (e.g. 0 km/h, 15 km/h, 50 km/h, 100 km/h and 250 km/h). Each characteristic indicates the size of the supporting torque for its driving speed in line with the steering torque.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB27FunctionSteering procedureDrive pinion Electromechanical power-assisted steering motor V187 Steering aid control unit J500Supporting torqueGBRack pinionSteering torque sender G269 with integrated torsion barSP58_60Steering angle sender G85 Steering pinionProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Input signal Output signal CAN DriveThe driver begins to steer. The torsion bar in the steering torque sender G269 is turned by the torque on the steering wheel. The steering torque sender detects the turn and reports the determined steering torque to the steering aid control unit J500. The steering aid sender G85 reports the actual steering angle and the steering speed to the steering aid control unit.The steering aid control unit determines the required supporting torque of the electromechanical power-assisted steering motor V187 from the steering torque, vehicle speed, engine speed, steering angle, steering speed and the characteristics stored in it. The sum from the steering torque and the supporting torque is the effective torque for the movement of the rack pinion.28Steering torqueeffective torqueActive resettingexternal resetting forceexternal resetting forceSP58_61If the driver uses no more force on the steering wheel, the steering torque is equal to zero and the torsion bar is released. On the basis of the axle geometry, resetting forces develop on the cramped wheels. Due to the friction in the steering system the effect of these external resetting forces is often too low to move the wheels again into the straightahead position.The steering aid control unit J500 determines the required supporting torque (resetting torque) from the well-known input sizes and the characteristics stored in it. The electromechanical power-assisted steering motor V187 is actuated and the wheels are turned back into the straightahead position.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted System behaviour in case of emergency unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�In case of undervoltage of the battery, the onboard supply control unit J519 ensures that sufficient current for the electromechanical power-assisted steering is available when engine is running. If necessary certain electrical consumers of low priority are switched off. If the system is completely switched off due to a system error, the legal requirements are further fulfilled, the vehicle remains unrestrictably steerable.29GBSupporting torque (= resetting torque)effective torque (= resetting torque)Steering torqueElectronics of the power-assisted steeringSteering torque sender G269SP58_46SP58_47The steering torque is determined with the aid of the steering torque sender G269 directly at the steering pinion. The sender operates according to the magnetic-resistant* function principle. In order to ensure a highest possible safety it possesses two independent areas designed in double (redundant).connected to the connecting piece of the steering column. Two poles are always used for the steering torque determination. The counterpart is a redundant, magneticresistant sensor element, which is fastened at the connecting piece to the steering gear.There is a torsion bar between the connecting If the steering wheel is operated, both connecting pieces rotate against each other piece of the steering column and the according to the occuring torque. As the connecting piece of the power-assisted magnetic magnet wheel rotates against the steering gear. sensor element, the occuring steering torque A magnetic magnet wheel with 24 poles is can be measured and transmitted as signal to fitted onto the connecting piece of the steering Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted the steering aid control unit. column. The magnet wheel is firmly unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Effects of failure In case of failure of the two areas on the steering torque sender, the power-assisted steering gear must be replaced. If a failure is detected, the steering assistance is deactivated. The deactivation is not performed suddenly, rather "soft". In order to achieve this "soft" deactivation, a steering torque replacement signal of the steering aid control unit is calculated from the • steering angle sender G85 and • electromechanical power-assisted steering motor V187. The electromechanical power-assisted steering motor V187 is still actuated via a time interval. A fault is displayed through the red lighting up of the warning light K161. In case of failure of only one of the two areas, the power-assisted steering continues to function without restriction. In this case the fault is displayed through the yellow lighting up of the warning light K161.30 magnetic magnet wheelConnecting piece of steering columnTorsion barredundant, magnetic-resistant sensor elementConnecting piece of power-assisted steeringSP58_48*Magnetic-resistant effect = modification of resistance of the electrical conductors through magnetization.GBSteering angle sender G85SP58_44Coil spring for airbagThe steering angle sender G85 is located behind the restoring ring with the slip ring Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted for airbag. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability It is seated on the steering columnwith between respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� the steering column switch and the steering wheel. It supplies the signal for determining the steering angle and the signal of the steering speed. Both signals are evaluated first in the steering column electronics control unit J527 and then transmitted via the CAN databus to the steering aid control unit J500.Steering angle sender G85Effects of failure In case of failure of the steering angle sender G85 an emergency operation programme is started. The missing signal is set to a replacement value. The steering assistance has its full function. The fault is displayed through the yellow lighting up of the warning light K161.SP58_45Steering column electronics control unit J527GB31Electronics of the power-assisted steeringAbsolute ring Incremental ringWorking mode Basic components of the steering angle sender G85 are: • a coding disc with two code rings • 7 pairs of light barriers with each one light source and an optical sensor The coding disc consists of two rings, the external absolute ring and the inner incremental ring.SP58_65Note: See also the description of the steering angle sender in the SSP no. 28.Absolute ringIncremental ringSegment 3Segment 4Segment 2The incremental ring is divided into 5 segments with each 72° and read off from a pair of light barriers. The ring has openings within the segment. The succession of the openings is similar within a segment, but different between the segments. This results in the coding of the segments. The absolute ring determines the angle. It is read off by six pairs of light barriers. The steering angle sender can detect the ± 1044° steering angle. It adds the angle degree. It detects that a steering wheel turn has been completed when exceeding the 360° marking. The constructive design of the steering gear enables ± 2.9 turns of the steering wheel.Segment 5Segment 1Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_66Pair of light barriers32GBThe measurement of the angle is performed according to the principle of the light barrier. If the incremental ring is used as a means of simplification, the source of light is located on the one side of the segment ring and the optical sensor on the other side.If light falls through a gap on a sensor, it results in a signal voltage.SP58_67If the light source is covered, the voltage is interrupted again.SP58_68Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�If one now moves the incremental ring, it results in a succession of signal voltages.SP58_69A succession of signal voltages per each pair of light barriers occur in the same way for the absolute ring. All successions of signal voltages are processed in the steering column electronics control unit. The system can calculate how far the rings were moved through the comparison of the signals. The starting point of the movement is determined by the absolute part.GB33Electronics of the power-assisted steeringElectromechanical power-assisted steering motor V187SP58_46SP58_50The electric motor V187 is a brushless asynchronous engine. It develops a maximum torque of 4.1 Nm, with which the steering is supported. Asynchronous engines do not possess a permanent magnetic field or an electrical excitation. Name-giving identification of asynchronous engines represents a difference between the frequency of the set voltage and the rotating frequency of the engine. Both frequences are not identical - this means also asynchronous. Asynchronous engines are simple in structure (without brushes) and therefore very safe for driving. Effects of failure An advantage of the asynchronous engine consists of the fact that the engine can be moved also in the dead condition via the steering gear. This means that in case of failure of the engine and the steering assistance the steering can be moved with low increased force.They possess a short response mode and thereby are suitable also for the fastest steering movements. The electric motor is fitted into an aluminium housing. It grips with a shaft end via a worm gear and a drive pinion into the rack pinion and thereby transfers the steering assisted force. There is a magnet at the other shaft end, which is used by the steering aid control unit for detecting the rotor speed. The signal serves the steering aid control unit for the determination of the steering speed.Even in the case of a short-circuit the engine is not blocked. A fault is displayed through the red lighting up of the warning light K161.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�34GBRotor speed senderThe rotor speed sender is a component of the electromechanical power-assisted steering motor V187. It is not accessible from the outside.Use of signal The rotor speed sender functions according to the magnetic-resistant* function principle and is similar in structure to the steering torque sender G269. It detects the rotor speed of the electromechanical power-assisted steering motor V187. The rotor speed sender transmits the information about the rotor speed to the steering aid control unit J500.Effects of failure In case of failure of the rotor speed sender, a replacement signal for the steering speed is used. The steering assistance is safely reduced. Thus a sudden deactivation of the steering assistance is avoided through sender failure. A fault is displayed through the red lighting up of the warning light K161.Vehicle speedThe vehicle speed signal is supplied by the ABS control unit. Effects of failureIn case of failure of the signal for the vehicle speed an emergency operation programme is Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability started. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� The driver has a full steering assistance, but no Servotronic function (i.e. speed-dependent steering assistance) is available. The fault is displayed through a yellow lighting up of the warning light K161.Engine speed sender G28The engine speed sender is a Hall sender. It is screwed into the housing of the crankshaft sealing flange. Effects of failure If the signal of the engine speed sender fails, use as replacement the last detected value of the engine speed. The fault is not displayed through lighting up of the warning light K161.*Magnetic-resistant effect = modification of resistance of the electrical conductors through magnetization.GB35Electronics of the power-assisted steeringSteering aid control unit J500SP58_46SP58_52The steering aid control unit J500 is fastened directly to the electromechanical powerassisted steering motor V187, so that a complex cable routing to the components of the power-assisted steering does not apply. On the basis of the input signals such as – – – – – – the steering angle signal, the engine speed, the steering torque, the rotor speed, the signal of the vehicle speed and the signal that the ignition key of the dash panel insert control unit J285 has been identified,A temperature sensor is integrated into the steering aid control unit, in order to detect the temperature of the steering system. If the temperature increases above 100 °C, the steering assistance is continuously reduced. If the steering assistance goes below a value of 60 %, the warning light for electromechanical power-assisted steering K161 lights up yellow.the control unit determines the respective requirement for steering assistance. The current of the exciter current is calculated and the electric motor V187 is actuated.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Effects of failureIf the steering aid control unit fails, the powerassisted steering is no longer assisted, but despite this the vehicle remains fully steerable. The warning light K161 lights up red.Note: In case of defective steering aid control unit J500 the complete power-assisted steering gear must be replaced. You will find the description for the replacement in the respective Workshop Manual.36GBElectromechanical power-assisted steering warning light K161The warning light is located in the display unit in the dash panel insert. It serves the display of malfunctions or interferences of the electromechanical power-assisted steering. The warning light lights up in two colours for malfunctions. Yellow lighting up means a warning. In case of red lighting up of the warning light, one must immediately go to a workshop. If the warning light lights up red, an acoustic warning signal sounds, a triple gong:Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP58_53When switching off the ignition the warning light lights up red, a self-check must be carried out for the system of the electromechanical power-assisted steering. Only if the signal comes from the steering aid control unit, the system functions properly, the warning light goes out. This self-check lasts approx. two seconds. When starting the engine the warning light goes out immediately. Note: The steering system detects and reacts to undervoltage. If the battery voltage drops below 9 Volt, the steering assistance is reduced until deactivation and the warning light K161 lights up red. In case of brief voltage interruption under 9 Volt the warning light K161 lights up yellow.GB37Function diagramFunction diagram+30 +15 31 S ST2p/2MT5a/4V187J500T5e/2 T5e/1 T5g/4 T5g/5 T5g/3 T5g/2T2p/1A BSP58_54G269Colour coding A B CAN data bus Low CAN data bus High Input signal Output signal Supply voltage J500 Steering aid control unit Earth S Fuse CAN data busG269 Steering torque senderV187 Electromechanical power-assisted steering motorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�inout38GB