TECHNICAL DOCUMENTATION

SSP 060 2,0 l 103kW Engine with DPF

PDFEN48 pages20 MB
SSP 060 2,0 l 103kW Engine with DPF - PDF cover

This PDF is currently unavailable.

Read document text
D1Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBssp60_GB.indd 14.5.2006 7:45:05 Modern diesel engines with direct injection find forever greater popularity, because they offer larger driving convenience due to the torque already available at low speeds. Diesel engines will remain perspective drive units in modern passenger vehicles also in the future because of their advantageous fuel consumption and carbon dioxide emission (CO2).Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBssp60_GB.indd 24.5.2006 7:45:06 ContentsPart I – 2.0 l/103 kW 2V Engine Main highlights of the engine Technical Data Balance shaft transmission Balance shaft transmission Exhaust system Exhaust pipe Exhaust gas recirculation Overview of components Overview of components Function diagram Function diagram Legend to function diagram Notes Part II – Diesel particle filter (DPF) Introduction What are the European Union standards? Pollutant formation during combustion Pollutants in the exhaust gas The particles Soot particle formation The measures for particle decrease Design and function The diesel particle filter system with additive The particle filter The regeneration of the particle filter The additive The soot loading of the particle filter Engine control during regeneration procedure Sensors and actuators System overview of diesel particle filter Sensors Actuators Function diagram Function diagram System limits Notes 19 19 20 21 22 23 24 26 26 27 28 30 31 32 33 33 34 42 45 45 46 47 4 5 6 6 8 8 10 12 12 14 14 16 17Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�You will find notes on inspection and maintenance, setting and repair instructions in the Workshop Manual. Time of going to press was on the 01. 12. 2005. This brochure is not subject to the update.GBssp60_GB.indd 34.5.2006 7:45:06 Part I – 2.0 ltr./103 kW 2V EngineThe design of the 2.0 l/103 kW TDI engine is based essentially on the 1.9 l/96 kW TDI, which is already used in ŠkodaSuperb vehicles.SP60_65Main highlights of the engine – Cylinder block is made out of cast iron– – – – – – Camshaft drive with toothed belt Cylinder head with 2-valve technology Engine with unit injection system Balance shaft transmission Contactless system for determining the position of the throttle valve Contactless system for determining the position of the exhaust gas recirculation valve – Diesel particle filter (DPF) with additive – Exhaust gas recirculation with cooling – Coolant pump integrated into the cylinder block – Oil pump drive of balance shaft transmissionProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBssp60_GB.indd 44.5.2006 7:45:07 Technical DataEngine code letters Design Displacement Bore Stroke Compression ratio Valves per cylinder Firing order max. power output max. torque Engine management Fuel Exhaust gas recirculation Emission standard BSS 4-cylinder inline engine 1 968 cm³ 81 mm 95.5 mm 18,5 : 1 2 1-3-4-2 103 kW at 4000 rpm 320 Nm at 1900 rpm Bosch EDC 15 Diesel at least 49 CZ Exhaust gas recirculation, Oxidation catalytic converter, Diesel particle filter (DPF) EU4Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Torque and power output diagramThe 2.0 l/103 kW TDI engine reaches its maximum power output of 103 kW at a speed of 4000 rpm. At a speed between 1600 to 2 700 rpm the engine has a torque of  300 Nm. The indicated power output and torque values are valid when operating with diesel fuel 49 CN (cetane number).70M = Max. torque n = Engine speed P = Power outputSP60_01GBssp60_GB.indd 54.5.2006 7:45:08 Balance shaft transmissionBalance shaft transmissionImproved driving convenience is ensured by the balance shaft transmission The balance shaft transmission is located below the cylinder block in the oil pan. The balance shaft transmission adjusts the occuring mass forces and reduces the occuring oscillations of the drive. Thus it contributes to a lower background noise in the interior. Humming and roar noises at high engine speed are clearly reduced. The transmission consists of two balance shafts, which together balance the mass forces of the second order. The balance shafts have a ratio 2:1 to the crankshaft (ratio into fast mode). The drive shaft of the balance shaft transmission is driven via a toothed gear, which is driven via an intermediate toothed gear of the crankshaft.Intermediate toothed gearCrankshaftBalance shaft transmissionSP60_12Oil pumpBalance shaft transmissionBalance weight Gear on the drive shaftProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Intermediate gearSP60_13The oil pump, which is connected directly to one of the balance shafts, is also integrated into the balance shaft transmission.GBssp60_GB.indd 64.5.2006 7:45:10 Top part of balance shaft transmissionDrive shaft of oil pumpBalance weightSP60_64Oil pumpBottom part of balance shaft transmissionProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBssp60_GB.indd 74.5.2006 7:45:11 Exhaust systemExhaust pipeThe exhaust pipe is designed as single-flow exhaust pipe with cooled exhaust gas recirculation, temperature sender of the exhaust gases, lambda probe before the catalytic converter, oxidation catalytic converter and the diesel particle filter (DPF). Due to the design of the exhaust system additives are necessary for the correct function of the diesel particle filter.Exhaust manifold Temperature sender in front of the turbocharger G507 The data of the sender is used for determining the injection period and fuel quantities as well as the dosage for the post-injection.SP60_54TurbochargerConnection for exhaust pressure sensor G450 The pressure sensor for exhaust gas G450 measures the pressure difference before and after the particle filter. The signal of the pressure sensor is transmitted to the control unit and is used for the calculation of the loading condition of the particle filter. Particle filter Filters the soot particles from the exhaust gases of the Protected engine by and copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability liquidates them through thermal with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� decomposition.GBssp60_GB.indd 84.5.2006 7:45:15 Connection of the exhaust gas recirculation The nitrogen emission is reduced by the exhaust gas recirculation. Under certain operating circumstances it can lead to the increase of the particle share in the exhaust gases.Lambda probe before the catalytic converter G39 determines the composition of the exhaust gases (oxygen portion) and transmits it as signal to the engine control unit J248, which then doses the fuel accordingly.Temperature sender in front of the particle filter G506 The engine control unit calculates the exhaust gas flow rate SP60_14 from the signal of the sender and thus determines the loading condition together with the signal of the pressure sensor. It is also used to protect the particle filter against too high Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted temperatures. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Decoupling element Separates the oscillation of the engine and balances the axial and radial movements of the exhaust pipe.Oxidation catalytic converter The main part of the carbon monoxides (CO), hydrocarbons (HC) and soot particles contained in the exhaust gases is converted in the catalytic converter to carbon dioxide (CO2) and water vapourGBssp60_GB.indd 94.5.2006 7:45:16 Exhaust systemExhaust gas recirculationOne part of the exhaust gases is guided back into the combustion chamber by means of the exhaust gas recirculation. Up to a certain ratio the share of the exhaust gas can positively affect the transfer of energy and thus lower the fuel consumption. The share of the exhaust gas can be up to 40 % depending on the operating condition. The sealing ratio and also the temperature in the combustion chamber increase when using the turbocharger and the direct injection. Thus the nitrogen share in the combustion chamber increases. In order to reduce the emission of the nitrogen oxides in diesel engines, the returned exhaust gases are cooled and thus the combustion peak temperature is decreased, so that larger quantities of the exhaust gases can be burned.Intake manifold flap motor V157Exhaust gas recirculation valve N18Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Coolant outletCoolant inletSP60_33Of exhaust manifoldRadiator for exhaust gas recirculation.Note: For this version it is not possible to regulate the cooling of the returned exhaust gases.10GBssp60_GB.indd 104.5.2006 7:45:33 Exhaust gas recirculation valve N18 The exhaust gas recirculation valve is designed as module and contains the following parts: - Exhaust gas recirculation valve (EGR) - Control engine for exhaust gas recirculation V338 - Exhaust gas recirculation valve sender G212 The position of the exhaust gas recirculation valve is calculated by the engine control unit, which transmits a PWM signal to the control motor for exhaust gas recirculation V338. The engine positions the regulating valve in the target position by means of the eccentric. The position is monitored contactless by the sender for exhaust gas recirculation valve G212. The data concerning the position is transmitted back to the engine control unit. This design of the exhaust gas recirculation valve N18 enables a stepless regulation of the exhaust gas recirculation.SP60_63Exhaust gasauthorised recirculation unless by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness ofTransmission information in this document. Copyright by ŠKODA AUTO A. S.� valve sender G212 Control engine for exhaust gas recirculation V338 Reverse springProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedGasketEccentricExhaust gas recirculation valve (control valve)SP60_59GB11ssp60_GB.indd 114.5.2006 7:45:34 Overview of componentsOverview of componentsAir mass meter G70 Engine speed sender G28 Hall sender G40 Diesel direct injection system control unit J248SensorsAccelerator pedal position sender G79 Accelerator pedal position sender 2 G185 Coolant temperature sender G62 Intake manifold pressure sender G71 Intake manifold temperature sender G72 CAN Drive K-wire Diagnostic connection CAN DiagnosisGB4.5.2006 7:45:39Brake light switch F Brake pedal switch F47 Clutch pedal switch F36 Fuel temperature sender G81 Exhaust pressure sensor G450 Temperature sender in front of the particle filter G506Temperature sender in front of the turbocharger G507Lambda probe before the catalytic converter G39Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Sender for empty fuel additive G504Exhaust gas recirculation valve sender G212Fuel gauge sender G12ssp60_GB.indd 12 ActuatorsFuel gauge sender G6 Fuel pump relay J17 Valve for pump/nozzle of cylinder 1 N240 Valve for pump/nozzle of cylinder 2 N241 Valve for pump/nozzle of cylinder 3 N242 Valve for pump/nozzle of cylinder 4 N243Data bus diagnostic interface J533Glow plug relay J52 Glow plugs for Engine Q6Pump for additive particle filter V135Lambda probe heater before the catalytic converter Z19Low heat output relay J359 High heat output relay J360Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Exhaust emission warning lamp K83 Glow period warning lamp K29Diesel particle filter warning lamp K231Solenoid valve for charge pressure control N75Exhaust gas recirculation valve N18; Control motor for exhaust gas recirculation V338Oil level/oil temperature sender G266Intake manifold flap motor V157SP60_32GB13ssp60_GB.indd 134.5.2006 7:45:44 Function diagramFunction diagramJ519+30 +15SS3 + 2 A 1 S S S S G6J179 Q13 Q12 Q11G504V135 G71G70J17J322G72Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S.Q10 ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�T94/30T94/63T94/16T94/37T94/80T94/78T94/62T94/38T94/76T94/60 T94/40T94/82T94/18T94/52J248T60/60 T60/25 T60/50 T60/24 T60/23 T60/49 T60/26 T60/60 T60/25 T60/25 T60/12 T60/28 T60/27 T60/39 T60/40 T60/32 T60/31 T60/48 T60/46 T60/47 T60/11 V157 N18 V338 G212 3 31 G28 G40 G81 N240 N241 N242 N24314GBssp60_GB.indd 144.5.2006 7:45:47T94/49T94/3 T94/5 T94/6 19+30 +154PTCSF36F+F47 CAN - H 31 CAN - LSSKJ322J359J360F60/F8G79G507G506G450G39Z19Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�T94/70T94/71T94/17T94/61T94/59 T94/83T94/39T94/84 T94/43T94/87T94/65 T94/23T94/53T94/75T94/11 T94/12 T94/15 T94/72T60/47T60/52T60/53T60/29T94/50T94/85T94/47T94/90T94/19T94/64T94/86T94/89N243G62N75ABCDEFG2 4T94/66T94/4 T94/2 T94/1T94/32 T94/54 T94/10 T94/77 T94/51T94/9GBNote: Legend to function diagram see on the page 16.SP60_5515ssp60_GB.indd 154.5.2006 7:45:47 Function diagramLegend to function diagramThe function diagram represents a simplified circuit diagram. Components A F F8 F36 F47 F60 G6 G28 G39 G40 G42 G62 G70 G71 G72 G79 G81 G212 G450 G504 G506 G507 J17 J179 J248 J322 J359 J360 J519 N18 N75 N240 N241 N242 N243 Battery V135 Pump for additive particle filter Brake light switch V157 Intake manifold flap motor Kick-down switch V338 Control motor for exhaust gas Clutch pedal switch recirculation Brake pedal switch S Fuse Idling switch Q10 Glow plug 1 Fuel pump for pre-supply Q11 Glow plug 2 Engine speed sender Q12 Glow plug 3 Lambda probe before the catalytic Q13 Glow plug 4 converter Z19 Lambda probe heater before the catalytic Hall sender converter Intake air temperature sender Coolant temperature sender Air mass meter Auxiliary signals Intake manifold sender Intake temperature sender A AC compressor - OFF Accelerator pedal position sender B AC readiness Fuel temperature sender C Radiator fan after-running Exhaust gas recirculation valve sender D Vehicle speed signal Exhaust pressure sensor E Heating element PTC - ON Sender for empty fuel additive F Generator DMF Temperature sender in front of the G Ignition/starter switch tml. 50 particle filter Temperature sender in front of the turbocharger Fuel pump relay Automatic glow period control unit Diesel direct injection system Diesel direct injection system relay Low heat output relay High heat output relay Colour coding Onboard supply control unit Input signal Exhaust gas recirculation valve Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Solenoid valve for charge pressure Output signal unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� control Supply voltage Valve for pump/nozzle of cylinder 1 Valve for pump/nozzle of cylinder 2 Earth Valve for pump/nozzle of cylinder 3 CAN data bus Valve for pump/nozzle of cylinder 4 Bidirectional Diagnostic connection16GBssp60_GB.indd 164.5.2006 7:45:48 NotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB17ssp60_GB.indd 174.5.2006 7:45:48 Part II – Diesel particle filter (DPF)After introduction of the EU4 emission regulations, the future EU5 standard, which will apply as of the year 2010, is the focus point in the efforts for development and a great challenge for all engine developers due to its limit values for nitrogen oxides (NOx) and particles.SP60_68The emission of the particles of a diesel engine can be clearly reduced by integrating a DPF - diesel particle filter system for exhaust treatment into the exhaust gas recirculation system. This filter can reduce the particle emission in the exhaust gases up to 97 % by using additives. The particles are kept in the filter and oxidize (combust) at temperatures around 500 °C. This prevents clogging of the filter that regenerates during the operation. In order to improve the regeneration, an additive on metallic basis is Protected by fuel, copyright. Copying forenables private or commercial purposes, in part or in whole, is not permitted low temperatures. proportioned into the which a full oxidation at relatively unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information this document. Copyright by ŠKODA AUTO A. S.� Furthermore, the additive contributes tointhe fact that fewer soot particles develop during the combustion of the fuel, and thus the life cycle of the system is extended.18GBssp60_GB.indd 184.5.2006 7:45:58 IntroductionWhat are the European Union standards?The efforts to reduce environmental damage due to vehicle traffic are noticeable since the 70‘s of the 20th century. At that time the first regulations for regulating the exhaust gases came into effect. A high reduction of the emissions was achieved in the last 15 years. The introduction of new technologies and the progress of electronics and computer technologies made it possible. The EU4 exhaust standard specifies limit values of all current pollutants in the exhaust gases of the combustion engines in grams per kilometer, in particular for the self-igniting engines of the passenger cars. The standard sets limit values of the pollutants also for trucks, whereby limit values exist depending upon weight categories.Nowadays the emission regulation 98/69/EG-B known as EU4 exhaust standard, which has replaced the regulation 98/69/EG-A (EU3), valid since the year 2000, applies to the European Union countries. This regulation introduces further reduction of the limit values for pollutants in the exhaust gases. In the Czech republic it applies as of 1st January 2006.Pollutant limit values according to the EU4 standard - passenger car Pollutant Carbon monoxide (CO) Hydrocarbons (HC) Nitrogen oxides (NOx) Diesel engines 0.50 g/km 0.25 g/km 0.30 g/km 0.025 g/km Petrol engines 1.00 g/km 0.10 g/km 0.08 g/km -Hydrocarbons (HC) + Nitrogen oxides (NOx)Soot particlesComparison of the limit values of the EU4 and EU3 standards Diesel engines Petrol engines0,7 0,6 0,5 0,4 0,3 0,2 0,1 00,642,50,56 0,50 0,502,302,0 1,50,30 0,251,0 0,50,051,000,200,025 EU 40,100,15 EU 30,08 EU 4EU 3EU 4EU 3EU 4EU 30EU 3EU 4EU 3EU 4COCOHCNOxCOHCNOxSP60_67SP60_66Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB19ssp60_GB.indd 194.5.2006 7:45:59 IntroductionPollutant formation during combustionThe pollutant formation and in particular the soot particle emissions are influenced by the combustion process in the diesel engine. This depends on many design, fuel and atmospheric factors. The following representation shows an overview of the input and output components of the diesel engine during combustion.Injected fuel: HC Hydrocarbons S SulphurSP60_03Drawn in air: O2 Oxygen N2 Nitrogen H2O Water (air humidity)Exhaust gas: O2 Oxygen N2 Nitrogen H2O Water CO2 Carbon dioxideCO HC SO2 NOx PM* Carbon monoxide Hydrocarbons Sulphur dioxide Nitrogen oxides Soot particlesThe exhaust gas of the diesel engine contains different components which must be evaluated in regards to the harmful effect on environment and health. The components oxygen, nitrogen and water already existing in the atmosphere are classified as innocuous.The carbon dioxide, which is contained in the atmosphere as natural gas, is classified within the limit range. It is not poisonous, however, with its increasing concentration it is one of the causes of the greenhouse effect. Harmful are carbon monoxide, hydrocarbons, sulphur dioxide, nitrogen oxides and soot particles.20unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedGBssp60_GB.indd 204.5.2006 7:46:34 Pollutants in the exhaust gasesCO Carbon monoxideCarbon monoxide (CO) develops from a lack of oxygen due to incomplete combustion of fuels containing carbon. It is a color -, odor- and tasteless explosive gas.SP60_04HC HydrocarbonsA multiplicity of different compounds (e. g. C6H6, C8H18) are designated as hydrocarbons, which occur after an incomplete combustion. They affect the organism in different ways. Some irritate, others (aromatic hydrocarbons) are cancerogenous.SP60_05SO2 Sulphur dioxideSulphur dioxide (SO2) results from the combustion of fuel containing sulphur. It is a colorless gas with a pungent smell. The share of the sulphur in the fuel is declining.NOx Nitrogen oxidesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability SP60_06 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP60_07Nitrogen oxides (NOx) (for example NO, NO2...) result from high pressure, high temperature and oxygen surplus during the combustion in the engine. Some nitrogen oxides are detrimental to one‘s health. Measures for the reduction of the fuel consumption can unfortunately lead to an increase of the nitrogen oxide concentration in the exhaust gas, because a more effective combustion leads to higher combustion temperatures.PM Soot particlesEach matter, which is contained in the exhaust gas under normal conditions as solid matter (ash, soot) or liquid, is evaluated as PM according to the US laws. In case of oxygen deficiency, it can lead to the formation of soot particles due to incomplete combustion.SP60_08 GB21ssp60_GB.indd 214.5.2006 7:46:34 IntroductionThe particlesParticle is an overall term for all small particles, solid or liquid, which develop through abrasion, cutting up, erosion, condensation as well as through an incomplete combustion. These processes produce particles with different forms, sizes and structures. Particles have the properties of air pollutants, if they are so small that they can float in gases and harm the organism.Soot particles Soot particles develop during the combustion process of a diesel engine. Soot particles are microscopically small carbon balls with a diameter of approximately 0.05 µm In the core they consist of pure carbon. Different hydrocarbon compounds, metallic oxides and sulphur deposit at this core. Some hydrocarbon compounds are classified as health precarious. The exact composition of the soot particles depends on the engine technology, the operating conditions and the fuel.HydrocarbonsSO4 (Sulphate)C (Carbon)Sulphur and metallic oxidesH2O (Water)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted SP60_09 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�22GBssp60_GB.indd 224.5.2006 7:46:35 Soot particle formationThe soot particle formation in the diesel engine depends on the individual procedures of the diesel engine combustion, like air supply, injection, propagation of flames. The combustion quality depends on how the mixture of air and fuel is formed. The mixture can be too rich in some areas of the combustion chamber, because there is insufficient oxygen. The combustion then remains incomplete and it results in a formation of soot particles.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Typical soot particle, which develops during the diesel engine combustion (about 1 million x enlarged)SP60_10The mass and the number of particles depend in principle on the quality of the engine combustion. The unit injection system ensures through the high injection pressure and an injecting process, which corresponds to the requirements of the engine, an efficient combustion and decreases thereby the formation of soot particles during the combustion process. A high injection pressure which results in a fine atomization of the fuel however does not necessarily lead to smaller particles. Measurements have shown that the size distributions of the particles in the exhaust gas, independent of the combustion principle of the engine, whether whirl chamber, Common Rail or Unit injection engines, resemble each other.GB23ssp60_GB.indd 234.5.2006 7:46:35 IntroductionThe measures for particle decreaseThe decrease of the exhaust emission of the diesel engine is an important aim for its further develop ment. There are various different technical solutions for the decrease of the exhaust emission. There by differ internal engine and external engine measures. Internal engine measures An emission reduction can be achieved through internal engine measures. An effective optimization of the combustion ensures that pollutants cannot develop.The following internal engine measures are:the design of the inlet and outlet channels for optimal flow conditions,high injection pressures through pump nozzle technology,the combustion chamber design, for example the decrease of the pollution area and the design of the piston recess.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP60_1124GBssp60_GB.indd 244.5.2006 7:46:36 External engine measures The release of the soot particles developed during the combustion can be prevented by external engine measures. This results in the reduction of the soot particles by means of the particle filter system. There are two different systems - the diesel particle filter with additive and the diesel particle filter without additive.System with additive This system is used for vehicles with a particle filter, which is not located close to the engine. Due to the long distance that the exhaust gas travels from the engine to the particle filter, the necessary ignition temperature for the combustion of the particles can only be achieved by adding an additive.Temperature of the exhaust gas in this area at partial load 750 °C Oxidation catalytic converterProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Particle filter unless authorised A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability 500 °C 620 °C by ŠKODA AUTO with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP60_61System without additive This system will be used in the future on vehicles with particle filter close to the engine. Due to the short distance that the exhaust gas travels from the engine to the particle filter, the temperature of the exhaust gas for the combustion of the particles is sufficiently high. If necessary the exhaust gas temperature can be increased by the engine control unit.Temperature of the exhaust gas in this area at partial load 750 °C Particle filter with integrated oxidation catalytic converter620 °CSP60_62GB25ssp60_GB.indd 254.5.2006 7:46:36 Design and functionThe diesel particle filter system with additiveIn the overview below are illustrated the components of the diesel particle filter system. On the following pages the structure and the function mode of the diesel particle filter system with additive are described.16SP60_151 2 3 4 5 6 7 8 9 Turbocharger Control unit in dash panel insert J285 10 Lambda probe before the catalytic Engine control unit purposes, converter G39 Additive container Protected by copyright. Copying for private or commercial in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability 11 Oxidation catalytic converter Sender for empty fuel additive G504 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� 12 Temperature sender in front of the particle Pump for additive particle filter V135 filter G506 Fuel tank 13 Particle filter Diesel engine 14 Exhaust pressure sensor G450 Temperature sender in front of the turbo charger G507 15 Silencer 16 Air mass meter G7026GBssp60_GB.indd 264.5.2006 7:47:39 The particle filterThe diesel particle filter is (for example in ŠkodaSuperb with 2.0 l/103 kW TDI engine) fitted in the exhaust pipe behind the oxidation catalytic converter. It filters the soot particles from the exhaust gases of the engine.SP60_16Structure The diesel particle filter consists of a honeycomb shaped ceramic body made of silicon carbide, which is located in a metal housing. The ceramic body is partitioned into a multiplicity of parallel arranged, microscopically small channels, which are alternatively closed. Silicon carbide is suitable as filter material because of the following properties: - - - - high mechanical resistance very good temperature change resistance thermal load capacity and conductivity high wear resistancehoneycomb shaped ceramic bodyProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP60_18SP60_17Function The passage of the exhaust gases through the particle filter is only possible, if the exhaust gases pass the porous walls between the input and output channels of the filter body. The soot particles on the input side of the filter remain closed.GB27ssp60_GB.indd 274.5.2006 7:47:40 Design and functionThe regeneration of the particle filterThe diesel particle filter must be cleared regularly from the soot particles, so that it does not clogg and its function is not impaired. During the regeneration, the soot particles collected in the filter are burned at a temperature of approx. 500 °C. The relevant ignition temperature of soot is approximately 600  - 650 °C. This exhaust gas temperature for the diesel engine can only be achieved at full load mode. The ignition temperature of the soot is decreased by adding an additive and the exhaust gas temperature is increased by an accurate engine control, in order to guarantee a regeneration of the diesel particle filter under all operating conditions. The regeneration procedure is initiated by the engine control unit.Particle filter emptyAir mass meter G70 Signals to engine control unitTemperature sender in front of the particle filter G506Exhaust pressure sender G450SP60_19Particle filter empty = low flow resistance Particle filter fullAir mass meter G70 Signals to engine control unitProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Temperature sender in front of the particle filter G506Exhaust pressure sensor G450SP60_20Particle filter empty = high flow resistance28GBssp60_GB.indd 284.5.2006 7:47:40 During the regeneration procedure, the collected particles are burned in the particle filter. It is performed, depending upon driving mode, every 500 - 700 kilometers and lasts about 5 - 10 minutes. The regeneration procedure is not noticed by the driver.Regeneration of the particle filterAir mass meter G70 Signals to engine control unitExhaust pressure sensor G450 Temperature sender in front Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted of the particle filter G506unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP60_21GB29ssp60_GB.indd 294.5.2006 7:47:41 Design and functionThe additiveThe additive is a substance containing iron, which is dissolved in a hydrocarbon mixture. In the ŠkodaSuperb it is located in a separate plastic tank in the spare wheel well.SP60_22The additive has the task to decrease the combustion temperature of the soot particles, in order to enable a regeneration procedure of the particle filter also at partial load mode. The ignition temperature of soot is approx. 600 - 650 °C. Such exhaust gas temperatures for diesel engines are achieved only in the full load. The ignition temperature of the soot is decreased to approx. 500 °C by means of the additive.The additive is rinsed automatically after each tank procedure via the fuel return-flow in the fuel tank. This occurs by means of a pump for additive particle filters controlled by the engine control unit. The fuelled quantity is determined through the evaluation of the fuel supply sender by the engine control unit. After each final dosing procedure there is a concentration of 10 ppm (parts per million) iron molecules in the fuel. This corresponds to a mixing ratio of approx. 1 litre additive per 2800 litres of fuel.The additive is added to the fuel together with the soot flows into the particle filter. There it deposits between the soot particles.SP60_2330Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted GB unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�ssp60_GB.indd 304.5.2006 7:47:41 The soot loading of the particle filterThe soot loading of the particle filter is constantly monitored by the engine control unit by means of calculation of the flow resistance of the filter. For determining the flow resistance, the exhaust flow rate in front of the particle filter must be in the ratio of the pressure difference before and after the particle filter. Pressure difference The pressure difference of the air flow before and after the particle filter is determined by the exhaust gas pressure sensor G450.Exhaust flow rate The exhaust flow rate is calculated by the engine control unit from the air mass current in the exhaust gas channel and the exhaust gas temperature in front of the particle filter. The air mass current of the exhaust gas corresponds to the air mass current in the suction channel, which is determined by the air mass meter G70. The volume of the exhaust air mass depends on the respective temperature. This is determined by the temperature sender in front of the particle filter G506. Depending on the exhaust gas temperature, the engine control unit can calculate the exhaust flow rate from the air mass current of the exhaust gas.Pressure difference Δp (kPa)30 25 20 15 10 5 0 100 200 300 400 500 600 700SP60_24Diesel particle filterfullProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted empty unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�defectiveFlow rate (m3 /h)The engine control unit puts the pressure difference in proportion to the exhaust flow rate and obtains from it the flow resistance of the particle filter. The engine control unit detects the soot loading from the flow resistance.GB31ssp60_GB.indd 314.5.2006 7:47:42 Design and functionEngine control during regeneration procedureThe engine control unit decides on the loading condition of the filter depending on the flow resistance of the filter. A high flow resistance points out the fact that the filter could be clogged up. The engine control unit initiates the regeneration procedure. At the same time: the exhaust gas recirculation is switched off, in order to increase the combustion temperature,SP60_45a post-injection is initiated, in order to increase the exhaust gas temperature after a quantity-re duced main injection, 35° crank angle according to the top dead center of the piston,SP60_46the intake air supply is regulated by the electrical throttle valve andProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP60_43the charge pressure is adapted, so that the torque does not change noticeably for the driver during the regeneration procedure.SP60_4432GBssp60_GB.indd 324.5.2006 7:47:45 Sensors and actuatorsDiesel particle filter overviewCAN Drive Control unit in dash panel insert J285Exhaust pressure sensor G450 Diesel particle filter warning lamp K231 Temperature sender in front of the particle filter G506 Diesel direct injection system control unit J248 Glow period warning lamp K29Temperature sender in front of the turbocharger G507 Pump for additive particle filter V135by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Lambda probeProtected before the unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability catalytic converter G39 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Lambda probe heater Z19Air mass meter G70 Diagnostic connection Valve for pump/nozzle N240 - N243Sender for empty fuel additive G504 Exhaust gas recirculation valve N18 Control motor for exhaust gas recirculation V338Exhaust gas recirculation valve sender G212SP60_56Fuel gauge sender GIntake manifold flap motor V157 33GBssp60_GB.indd 334.5.2006 7:47:46 Sensors and actuatorsSensorsExhaust pressure sensor G450 The pressure sensor for exhaust gas functions according to the Piezo principle. Use of signal The pressure sensor for exhaust gas measures the pressure difference of the exhaust gas current before and after the particle filter. The signal of the exhaust pressure sensor G450, the signal of the temperature sender in front of the particle filter G506 as well as the signal of the air mass meter G70 form an inseparable unit when determining the loading condition of the particle filter. Effects of signal failure If the signal of the exhaust pressure sensor G450 fails, the regeneration of the particle filter takes place first cyclically according to driven distance or operating hours. The particle filter cannot be regenerated permanently and reliably in this way. According to a defined cycle number, first the diesel particle filter warning lamp K231 and then the flashing glow plug warning lamp K29 are displayed in the dash panel insert. Thus the driver must go to a workshop.SP60_35Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Structure There are two pressure connections at the exhaust pressure sensor 450. From one of the connections a pressure pipe leads to the exhaust current in front of the particle filter and from the other one to the exhaust current behind the particle filter. A diaphragm with Piezo elements, which has an effect on the respective exhaust pressures, is located in the sender.Pressure before the filter Pressure after the filter Diaphragm with Piezo elements Signal to control unitSP60_3634GBssp60_GB.indd 344.5.2006 7:47:50 Function Particle filter – empty For a particle filter with very small particle loading the pressure in front and behind the filter is almost alike. The diaphragm with the Piezo elements is in the rest position.DiaphragmPiezo elementsSP60_37Pressure before the filter = pressure after the filterParticle filter – full If soot has been collected in the particle filter, the exhaust pressure in front of the filter increases through a reduced flow rate. The exhaust pressure behind the filter remains almost the same. The diaphragm deforms itself according to the pressure difference. This deformation alters the electrical resistance of the Piezo elements, which are interconnected to a measuring bridge. The output voltage of this measuring bridge is prepared and strengthened by the sensor electronics and sent to the engine control unit as signal voltage. The engine control unit determines from this signal the loading condition of the particle filter and initiates a regeneration procedure for the cleaning of the filter.Diaphragm with Piezo elementsSP60_38Pressure before the filter pressure after the filterProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The loading condition of the particle filter can be read out using the vehicle diagnosis, measuring and information system VAS 5051 or VAS 5052 in a measured value block as „particle loading factor“, which is given in %.GB35ssp60_GB.indd 354.5.2006 7:47:51 Sensors and actuatorsTemperature sender in front of the particle filter G506SP60_41SP60_42The temperature sender in front of the particle filter is a PTC sensor. For a sensor with PTC (Positive Temperature Coefficient) the resistance increases as the temperature rises.It is located in the exhaust pipe in front of the diesel particle filter and measures there the temperature of the exhaust gas.Use of signal The engine control unit calculates the exhaust flow rate from the signal of the temperature sender in front of the particle filter G506, in order to determine the loading condition of the particle filter.Effects of signal failure If the signal of the temperature sender in front of the particle filter G506 fails, the regeneration of the particle filter takes place first cyclically according to driven distance or operating hours.The particle filter cannot be regenerated permaThe signal of the temperature sender in front of nently and reliably in this way. According to a Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not number, permitted the particle filter G506, the signal of the air mass defined cycle first the diesel particle filter unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness information in this document. Copyright by ŠKODA AUTOK231 A. S.� and then the flashing glow meter G70 as well as the signalofof the exhaust warning lamp pressure sensor G450 form an inseparable unit plug warning lamp K29 are displayed in the dash when determining the loading condition of the panel insert. Thus the driver must go to a workparticle filter. shop. In addition the signal is used as component protection, in order to protect the particle filter against too high exhaust gas temperatures.36GBssp60_GB.indd 364.5.2006 7:47:55 Temperature sender in front of the turbocharger G507SP60_39SP60_52The temperature sender in front of the turbo charger is a PTC sensor. It is located in the exhaust pipe in front of the turbocharger and measures there the temperature of the exhaust gas.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Use of signal The engine control unit needs the signal of the temperature sender in front of the turbocharger for the calculation of the start of injection and the injection quantity for the post-injection during the regeneration procedure. Thus the necessary temperature increase of the exhaust gas is achieved for the combustion of the soot particles. In addition the turbocharger is protected by the signal against inadmissibly high temperatures during the regeneration.Effects of signal failure In case of failure of the temperature sender in front of the turbocharger G507, the turbocharger can no longer be protected against inadmissibly high temperatures. A regeneration of the diesel particle filter does not take place. The glow plug warning lamp K29 indicates to the driver that he must go to a workshop. In order to reduce the soot emissions, the exhaust gas recirculation is switched off.GB37ssp60_GB.indd 374.5.2006 7:48:01 Sensors and actuatorsLambda probe before the catalytic converter G39 The lambda probe is a broadband lambda probe. It is located in the exhaust manifold in front of the oxidation catalytic converter.Use of signal The lambda probe determines the oxygen share in the exhaust gas over a large measuring range. In connection with the diesel particle filter system the engine control unit uses the signal of the lambda probe for the exact calculation of the quantity and the timing for the post-injection during the regeneration procedure. A minimum oxygen content in the exhaust gas with a continuously high exhaust gas temperature is required for an effective regeneration of the particle filter. This control is made possible by the signal of the lambda probe in combination with the signal of the temperature sender in front of the turbo charger.SP60_40Effects of signal failureElectrical circuitT94/10The failure of the lambda probe can lead to increased nitrogen oxide emissions.J248 G39 Z19 S Diesel direct injection system Lambda probe before the catalytic converter Lambda probe heater before the catalytic converter FuseZ19 G39 ST94/51T94/77T94/54T94/32The regeneration of the particle filter is more inaccurate, however it remains reliable. The glow Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted J248 or accept any liability unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee plug warning lamp K29 and exhaust gas warning with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� lamp K83 light up in the dash panel insert.SP60_5838GBssp60_GB.indd 384.5.2006 7:48:03 Air mass meter G70 The hot film air mass meter is fitted in the suction channel. The engine control unit determines the actual air mass which is suctioned through the air mass meter .Use of signal In combination with the diesel particle filter system, the signal for the calculation of the exhaust flow rate is used in order to determine from it the loading condition of the particle filter. The signal of the air mass meter G70, the signal of the temperature sender in front of the particle filter G506 as well as the signal of the exhaust pressure sensor G450 form an inseparable unit when determining the loading condition of the particle filter.SP60_53Effects of signal failureProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted If the signal of the air mass meter G70 fails, the unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� regeneration of the particle filter takes place first cyclically according to driven distance or operating hours.The particle filter cannot be regenerated permanently and reliably in this way. According to a defined cycle number, first the diesel particle filter warning lamp K231 and then the flashing glow plug warning lamp K29 are displayed in the dash panel. Thus the driver must go to a workshop.GB39ssp60_GB.indd 394.5.2006 7:48:05 Sensors and actuatorsSender for empty fuel additive G504 The sender for empty fuel additive is located in the additive container.Additive containerSP60_50SP60_51Sender for empty fuel additive G504Glow period warning lamp K29Use of signal The glow plug warning lamp K29 in the dash panel insert is activated by the signal of the emp ty fuel additive sender G504 as of a determined remaining capacity in the additive container. In case of a malfunction in the diesel particle filter system, the driver must go to a workshop. In case of a very low quantity of additive, the particle filter regeneration is blocked and the engine performance is reduced.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Dash panel insertSolenoid ringFloatSP60_47Reed contact40GBssp60_GB.indd 404.5.2006 7:48:08 Function A reed contact is installed in the shank of the sender for fuel additive tank. It is switched by the solenoid ring installed at the float. If sufficient additive is in the additive container, the float rests against the upper stop. The reed contact is open.Solenoid ring FloatReed contact AdditiveSP60_49Solenoid ringIf there is not sufficient additive in the additive container, the float drops down to the bottom stop. The reed contact is closed by the solenoid ring. The glow period warning lamp K29 is switched on.FloatReed contact AdditiveSP60_48Effects of signal failure An entry is made in the fault memory of the engine control unit in case of signal failure of the sender for empty fuel additive. The glow plug warning lamp K29 and exhaust gas warning lamp K83 light up in the dash panel insert.Electrical circuitJ248T94/16 T94/37Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�G504SP60_57 GB41ssp60_GB.indd 414.5.2006 7:48:10 Sensors and actuatorsActuatorsPump for additive particle filter V135SP60_34SP60_25The pump for additive particle filter is a strokepiston pump, which delivers the additive to the fuel tank. It is screwed onto the additive container.After each tank procedure, the pump is controlled with clock pulses by the engine control unit, in order to proportion the additive in the correct quantity.Function principle Deliver additiveArmature chamber Solenoid armature from additive containerFeed hole to fuel tankProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Solenoid coilValve ballSP60_26SpringPump plungerThe pump is filled with additive in the de-energized condition As soon as the engine control unit controls the pump for additive particle filter, the solenoid coil is energized and the solenoid armature moves the pump piston against the spring force. The pump piston closes the feed hole to the pump interior and presses the additive located in the pump interior towards the valve ball.A pressure results from this procedure, so that the valve ball opens the pump interior. The exact quantity of additive defined by the volume of the pump interior chamber is now delivered to the fuel tank.42GBssp60_GB.indd 424.5.2006 7:48:11 Suction additiveFeed hole Pump interior chamber to fuel tankArmature chamber Solenoid armature from additive containerSolenoid coil Spring Pump plungerValve ballSP60_27During the suction procedure the additive runs into the armature chamber. The solenoid coil is not controlled by the engine control unit and the spring presses the pump plunger back. At the by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted same time the valve ball Protected closes the pump interior unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability chamber. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Armature chamber Solenoid armature from additive containerFeed hole Pump interior chamber to fuel tankSolenoid coil Spring Pump plungerValve ballSP60_28The pump plunger moves into the initial position. The developing negative pressure thereby suctions additive via the opened feed hole from the armature chamber into the pump interior chamber.GB43ssp60_GB.indd 434.5.2006 7:48:12 Sensors and actuatorsDiesel particle filter warning lamp K231 The diesel particle filter K231 warning light is located in the dash panel insert. It lights up, if the diesel particle filter cannot be regenerated during extreme short-distance operation.Task In case of longer short-distance operation, the regeneration of the diesel particle filter can be impaired. Thus it can lead to damage of the particle filter and the engine. If the engine does not achieve the necessary operating temperature over a longer period, in order to burn the accumulated soot in the particle filter, the diesel particle filter warning light K231 lights up in the dash panel insert.SP60_29This signal informs the driver that he should briefly increase the driving speed (at least 60 km/ h for the period of 5 - 10 min). The temperature of the exhaust gases increases through the higher driving speed. This temperature is sufficient for the regeneration of the particle filter. If the regeneration was performed, the warning light K231 goes out.You will find in the Owner‘s Manual detailed information regarding operation, if the diesel particle filter warning light K231 is lit. In each case traffic regulations and speed limits must be kept.Exhaust emissions warning lamp K83 The exhaust relevant components of the diesel particle filter system are examined in the context of the EOBD (Euro On Board Diagnosis) for failure and malfunctions. The exhaust warning lamp K83 on the dash panel insert, which is also called MIL (Malfunction Indicator Light), indicates possible malfunctions of the components, which influence the emission treatment. You will find in the self study program No. 39. detailed information for the exhaust warning lamp and the EOBD systemSP60_3044Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBssp60_GB.indd 444.5.2006 7:48:13 Function diagramFunction diagram30 15K231 J322 J533 S G J285SS V135 G39SSV157N75N18 V338 G212Z19T94/49T94/80T94/32T94/54T94/10T94/77T94/51T60/60T60/25T60/29T60/26T60/50T60/49T60/23T60/24T94/89T94/66J248T94/60 T94/40 T94/82 T94/12 T94/15 T94/16 T94/37 T94/23 T94/53 T94/75 T60/31 T60/48 T60/46 T60/47 T94/11 T94/9 T60/1G70G450G504G507G506N240 N241N242 N243SP60_31G Fuel gauge sender N243 Valve for pump/nozzle of cylinder 4 G39 Lambda probe before the catalytic Pump for additive particle filter Protected by copyright. Copying for private or commercial purposes, in part or in whole, V135 is not permitted unless authorised by Š KODA AUTO A. S. Š KODA AUTO A. S. does not guarantee or accept any liability with respect converter V157 Intake manifold flap motor to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� G70 Air mass meter V338 Control motor for exhaust gas recirculation G212 Exhaust gas recirculation valve sender valve G504 Sender for empty fuel additive Z19 Lambda probe heater before the catalytic G506 Temperature sender in front of the particle converter filter G507 Temperature sender in front of the turbocharger J248 Diesel direct injection system J285 Control unit in dash panel insert J322 Diesel direct injection system relay Colour coding J533 Data bus diagnostic interface J533 Input signal K231 Diesel particle filter warning lamp N18 Exhaust gas recirculation valve Output signal N75 Solenoid valve for charge pressure Supply voltage control N240 Valve for pump/nozzle of cylinder 1 Earth N241 Valve for pump/nozzle of cylinder 2 CAN data bus N242 Valve for pump/nozzle of cylinder 3 BidirectionalGBT94/72T94/6T94/5T94/345ssp60_GB.indd 454.5.2006 7:48:14 System limitsThe short-distance operation In order to initiate the regeneration process in the diesel particle filter, the exhaust gas temperature is increased by a targeted engine control. For permanent short-distance drives it is not possible to increase the exhaust gas temperature in sufficient measure. The regeneration cannot successfully take place. The following regenerations with very high soot loading of the filter can lead to temperature increases during the combustion of the soot and to the damage of the particle filter.Or the filter can clog during very high loads. This blockage of the filter can lead to a standstill of the engine. In order to avoid this, the diesel particle filter warning light K231 in the dash panel insert is activated as of a certain limit value of the filter loading or as of a certain number of unsuccessful regenerations.The fuel suitability For proper functioning of the system it is necessary that a certain ratio of additive and soot particles in the particle filter is not below the limit. Observe that the fuel corresponds to the DIN standard. Operating the vehicle with biodiesel is not possible due to the present quality and a clearly reduced oxidation stability of this fuel. A very high sulphur content in the fuel leads to an impaired function of the particle filter system with higher fuel consumption through increased regeneration.The emissionsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The driving cycle with regeneration can lead to increased emissions. An oxidation from soot to carbon dioxide (CO2) takes place during the regeneration. Carbon monoxide (CO) develops, if not enough oxygen is available during this process. An emission test (NEDC - New European Driving Cycle) is carried out, in order to determine the exhaust emission. The values from a cycle without as well as with regeneration process are evaluated. The determined values must be applied so that the vehicle fulfils the exhaust standard EU4.46GBssp60_GB.indd 464.5.2006 7:48:14 NotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB47ssp60_GB.indd 474.5.2006 7:48:14 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�48GBssp60_GB.indd 484.5.2006 7:48:14