TECHNICAL DOCUMENTATION
SSP 035 1,4 AUA 55kW AUB 74kW 16V Petrol engines Magneti Marelli

This PDF is currently unavailable.
Read document text
New modern vehicle concepts such as the Fabia also call for matching power units. Consequently, the two new engines 1.4-ltr. – 16 V 55 kW and 1.4-ltr. – 16 V 74 kW are used on the Fabia. These engines are representatives of a new generation of engines in the Group. In addition to offering a number of new technical highlights, they are particularly characterised by their lightweight design, improved fuel consumption, environmental friendliness and low noise emissions.SP35_13SP35_1355 kW/74 kW … Who's who then?You will be acquainted with the design and functional details of the engines in this Self-Study Programme.2Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBContentsEngineering Engine Mechanical Components Air Filter Fuel Supply System Exhaust System System Overview Engine Management System Emission Control System Exhaust Gas Recirculation System Function Diagram Self-DiagnosisProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Test Your Knowledge with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�4 6 20 22 26 28 30 34 40 44 47 49Servicexxxxxxxxxxxxxxxx FABIAServicexxxxxxxxxxxxxxxx FABIAService Service Service Service Servicexxxxxxxxxxxxxxxx FABIA xxxxxxxxxxxxxxxx FABIA xxxxxxxxxxxxxxxx FABIA xxxxxxxxxxxxxxxx FABIA xxxxxxxxxxxxxxxx FABIAS e r v i c eXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXYou will find notes on inspection and maintenance, setting and repair instructions in the Workshop Manual.GB3EngineeringTechnical dataDifferences/Common features100020001.4-ltr. – 16 V (55 kW) AUASP35_043000 n (1/min)4000500060007000SP35_14Engine code letters Type Displacement Bore Stroke Compression ratio Rated output TorqueAUA 4-cylinder in-line engine 1390 cm3 76.5 mm 75.6 mmAUBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted : AUTO 1 A. S. does not guarantee or accept any liability unless authorised by ŠKODA AUTO A. S.10.5 ŠKODA with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�55 kW at 5000 rpm 126 Nm at 3800 rpm74 kW at 6000 rpm 126 Nm at 4400 rpm4GB100020001.4-ltr. – 16 V (74 kW) AUBSP35_503000 n (1/min)4000500060007000SP35_15Engine code letters Engine management system Lambda control system Knock control system Ignition system Emission standard Intake system Oil pan Throttle valve FuelAUAAUBMagneti Marelli 4LV multipoint fuel injectionProbe upstream of cat Probe downstream of cat 1 knock sensor Rotorless high-voltage distribution system with 2 double-spark ignition coils EU4 Plastic intake manifold Sheet steel Small cross section Die cast aluminium intake manifold Aluminium, with integrated enginegearbox support Enlarged cross sectionProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Unleaded petrol 95 RON Unleaded petrol 98 RON unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability (91 possible with reduced output) (95 possible with reduced output) with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB5Engine Mechanical ComponentsThe intake manifoldTwo different versions are used in these engines – – 1.4-ltr. – 16 V 55 kW engine – plastic 1.4-ltr. – 16 V 74 kW engine – metalInjectors Fuel railto the cylindersIntake manifold (resonance manifold)Intake air from filterSP35_51Throttle valve control unitIntake manifold complete – metal versionProtected by copyright. Copying for private or commercial purposes, inIn part or in whole, is not permitted The following components are installed at the addition, the intake manifold features two unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability intake manifold: mounting studs for with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� the engine trim panel with air filter. – Injectors – Fuel rail – Throttle valve control unit – Intake manifold pressure sender with intake manifold temperature sender6GBIntake manifold manufactured of plastic The intake manifold consists of three parts which are connected to each other as non-detachable parts. The material used is polyamide, which is heat-resistant for short periods up to a maximum of 140 ˚C. The intake manifold has a specific geometrical design to take into account the material used. The use of polyamide offers weight savings of some 36 % compared to a comparable intake manifold made of metal.SP35_52Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Intake manifold manufactured of metal It is manufactured from aluminium and consists of six parts which are bolted to each other. The main body and the manifold cover are aluminium die castings. The resonance pipes are sand castings.SP35_53GB7Engine Mechanical ComponentsThe valve gearThe cylinder head contains the valves, the roller rocker fingers and the hydraulic supporting elements (plunger). The inlet camshaft and the exhaust camshaft are mounted in the camshaft housing. The camshaft housing at the same time performs the function of the cylinder head cover. The camshafts are mounted on 3 bearings and inserted into the camshaft housing. Their axial play is limited by the camshaft housing and the end covers. 4Plungers Exhaust camshaft Roller rocker finger Camshaft housingInlet camshaftSP35_16Cylinder headValveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�End covers Inlet camshaftExhaust camshaftCamshaft housingCylinder headSP35_17Note: Camshaft housing and cylinder head are sealed using a liquid sealant. The sealant must not be applied too thick.Excess sealant might otherwise get into the oil drillings and thus cause engine damage.8GBOperation of valves by roller rocker fingersAdvantages: – reduced friction – small number of moving masses – low level of force required by engine to operate valvesCamshaft Cam roller Roller rocker finger Securing clamp Valve stem Hydraulic supporting elementRoller bearing of cam rollerSP35_20Design The roller rocker finger consists of a lever The specific design of the supporting element Protected copyright. Copying for private or commercial purposes, that in part the or in whole, not permitted manufactured as a metalby formed part, and a cam ensures camisroller is positioned against unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability roller with roller bearing. camshaft, both when supporting elements with respect to the correctness of information in this the document. Copyright by ŠKODA AUTO the A. S.� are installed, as well as during subsequent It is supported at the one side on the supporting operation of the engine. element and on the other side on the valve stem. The piston of the supporting element adapts accordingly in terms of its height position. At the supporting element, it is held by a securing clamp and placed on at the valve stem. This design compensates not only for installation tolerances, thermal expansion but also for wear The hydraulic supporting element is similar in over the life of the engine. terms of its function to the hydraulic bucket tappet. The cam stroke is transmitted to the valve stem with a low level of friction.GB9Engine Mechanical ComponentsThe hydraulic supporting elementconsists of the main components of the piston – in turn subdivided into top and bottom part of piston – cylinder and piston spring. It is linked to the oil circuit of the engine. A small ball together with the compression spring in the high-pressure chamber acts as a one-way valve. The installed height of the supporting element can be set both during installation as well as in subsequent operation of the engine so as to constantly compensate for any play which is produced in the valve gear. The mechanism of the compensation is characterised essentially by the following two processes.One-way valve Top part of piston Cylinder Oil reservoir Leak gap 2 Oil passage Leak gap 1 Bottom part of piston High-pressure chamber Piston springSP35_25Lower of the piston When the cam runs onto the cam roller, the piston of the supporting element is pressed slightly into the cylinder. This is possible because the oil of the high-pressure chamber, which is subjected to increasing pressure, is forced out through the leak gap between cylinder and bottom part of piston 1 and is able to escape into the oil reservoir (slight quantities of oil also escape through the leak gap between cylinder and top part of piston 2 . The lowering of the piston results in a slight play in the valve gear 3 , which is then, however, immediately compensated for again.SP35_27Compensating play When the cam runs off the cam roller, the piston pin again pushes the piston sufficiently far out of the cylinder 4 , until the cam roller moves against the cam and compensates for the play produced. At the same time, the oil pressure in the high-pressure chamber is reduced. The oneway valve opens and oil flows into the highpressure chamber. Once the pressure between oil reservoir and high-pressure chamber is balanced, the one-way valve closes. .SP35_26Play 3 410Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBFunction when valve operated During the movement of the roller rocker finger, the hydraulic supporting element acts as a support of the roller rocker finger and as a pivot point. The cam runs on the cam roller and pushes the rocker finger down. The valve is operated by the rocker finger. The lever arm between cam roller and supporting element is smaller than between valve and supporting element. Consequently, a large valve stroke is achieved with a relatively small cam.CamCam rollerRocker fingerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP35_24Lubrication Lubrication between the hydraulic supporting element and the roller rocker finger, as well as between the cam and the cam roller, makes use of oil drillings in the supporting element. In this case, the oil sprays through a drilling in the roller rocker finger onto the cam roller.OilCam rollerSP35_23Note: It is not possible to check the hydraulic supporting elements.Oil passage in cylinder head Oil drilling in supporting elementGB11Engine Mechanical ComponentsThe camshaft driveThe two camshafts are driven by a toothed belt running on toothed belt sprockets.Main drive toothed belt Coupling drive toothed beltBecause of the compact overall width of the cylinder head, the toothed belt drive is split into a main drive and a coupling drive. Guide pulley Main driveCoolant pump belt pulleyCoupling drive tensioning pulley Guide pulleyThe coolant pump and the inlet camshaft are driven by the crankshaft by means of toothed belt of the main drive. An automatic tensioning pulley and two guide pulleys prevent the toothed belt from oscillating.Main drive tensioning pulleyCrankshaft toothed belt sprocketSP35_28Coupling drive The toothed belt of the coupling drive is located immediately behind the toothed belt of the main drive, outside of the camshaft housing. In the coupling drive, the exhaust camshaft is driven by the inlet camshaft by means of a toothed belt. In this case also, an automatic tensioning pulley prevents oscillations of the toothed belt.Inlet camshaft sprocketCoupling drive Exhaust camshaft sprocketTensioning pulleySP35_29Note: Fit holes Fit holes are provided in the camshaft housing and in the gears of the camshaft for installation, and for setting of the timing. Both gears are fixed in place using a special tool. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Further information on this can be by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability unless authorised with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� found in the Workshop Manual Fabia, 1.4-ltr./55 kW; 1.4-ltr./74 kW Engine, Mechanical Components.SP35_3212GBThe cylinder blockThe cylinder block of both engines is an aluminium die casting. A very slim design has been adopted with the aim at achieving weight savings. The necessary stiffness is achieved by pronounced ribbing, the stiffness being further enhanced by the bearing pedestals for the crankshaft bearings (refer also to crankshaft, important!). The cylinder liners are manufactured from cast iron. They are integrally cast and can be machined. The webs with integrated cast liners are 5.5 mm thick and have likewise been designed very slim.Web with integrated cast linersCoolant passageProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Note: Only coolant additive G12 may used. This prevents not only frost damage to the aluminium housing but also scale deposits and corrosion damage in the coolant passages.SP35_33GB13Engine Mechanical ComponentsThe crankshaftThe crankshaft is manufactured from grey cast iron and features only four balancing weights. Despite this weight saving, the crankshaft offers the same running properties as the crankshaft with eight balancing weights. The bearing pedestals enhance the inner stiffness of the aluminium cylinder block.Bearing pedestalsBalancing weightBearing pedestalsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP35_34Balancing weight Bearing cap Bearing capBalancing weight Bearing capNote: The crankshaft must not be slackened or removed. The moment the bearing cap bolts are slackened, this results in the stress in the inner structure of the aluminium bearing pedestals of the cylinder block being relieved, which in turn causes a deformation of the bearing pedestals. As a result of this deformation the bearing play is reduced.Even if the bearing shells were not replaced, bearing damage can result from the altered bearing play. If the bearing cap bolts have been slackened, it is then necessary to replace the cylinder block complete with the crankshaft. It is not possible to measure the crankshaft bearing play with workshop equipment.14GBThe connecting rodDepending on the production location, connecting rods are manufactured using two different machining methods: 1. cutting, 2. cracking.Cutting If cutting is employed, the connecting rod is first of all pre-machined roughly and then cut apart into conrod and conrod cap. Both parts are bolted together for final machining.SP35_35CrackingIf the cracking process is employed, the connecting rod is machined as a complete part. A predetermined breaking point is made at the base of the conrod using a laser beam for the subsequent cracking process. Following this, conrod and conrod cap are separated by applying considerable force with a tool. The advantages: –Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability SP35_36 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�This process produces an unmistakable fracture surface. The conrod cap fits only in one position and only to the matching conrod. – Manufacturing is more cost-effective and it is possible to reduce the weight of the conrod. – Good positive connection because of the rough surface of the fracture surface and the high jointing accuracy. – No additional centring aids necessary.SP35_37SP35_38Predetermined breaking pointOnly conrods manufactured using the cracking process are fitted to the 1.4-ltr. – 16 V 55/74 kW engines.Note: Conrods must always be replaced as a set. Don't forget to mark the conrod to the matching cylinder.GB15Engine Mechanical ComponentsThe sealing flangeThe cylinder block is sealed on the flywheel side by means of a sealing flange. The sealing flange also includes the sensor gear for the engine speed sender G28.Note: In this new generation of engines, sealing flanges with a new sealing system are installed. The design (e.g. the housing of the engine speed sender) is so different that, when a new sealing flange is installed, only the type of sealing flange which was previously installed, must be used.Engine speed sender G28Sealing flange with spring lock washer seal On this type, the seal between the sealing flange and the sensor rotor is achieved by means of a spring lock washer seal. The sensor rotor in addition has an elastomere seal to the crankshaft side. The sensor rotor is pressed onto the crankshaft in exactly the correct position.SP35_41Sealing flange Crankshaft Elastomere seal Sensor rotorSensor rotorCrankshaftSealNote: The seal is achieved at the sensor rotor.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Sensor rotor Sealing flangeSP35_4216GBSealing flange with PTFE sealing ring PTFE means polytetrafluoroethylene. It is more commonly known by the name Teflon and is used to describe a certain type of heat and wear-resistant plastic. The PTFE sealing ring provides a direct seal between the sealing flange and the crankshaft. Consequently, it is not necessary to have an additional elastomere seal. With this type of sealing flange as well, the sensor rotor is pressed on in exactly the correct position.PTFE sealEngine speed sender G28You will find more detailed instructions for installation of the various sealing flanges in the Workshop Manual.CrankshaftSP35_40PTFE sealing ringSealing flange Sensor rotorCrankshaftNote: The seal is achieved at the crankshaft.Sensor rotor Sealing flangeProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted SP35_39 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB17Engine Mechanical ComponentsThe oil pumpThe oil pump is driven directly by the crankshaft. The inner rotor of the oil pump is mounted directly on the front stud area of the crankshaft. It is know as the duocentric oil pump. As a result of the particular shaping of this area it has been possible to design an oil pump with a very small outer diameter. The term "duocentric" is based on the geometrical offset of the axes of the inner rotor and outer rotor. In addition to achieving low friction and a weight saving of some 1 kg, the direct drive by the crankshaft also reduces the noise level produced in the engine. The oil pump housing seals off the cylinder block to the front.SP35_44Crankshaft stud with polygon profile (polygon = regular multiple planes)Oil pump housingOuter rotor Inner rotorOil pump housing coverSP35_4318Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBFunction The inner rotor is located on the crankshaft stud and drives the outer rotor. As a result of the different rotating axes of the inner rotor and outer rotor, an enlarged space is produced on the inlet side during the rotational movement. Oil is drawn in along an intake line and transported on to the delivery side.SP35_48Oil is drawn inOil is pressed into the On the delivery side, the space between the teeth Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted becomes increasingly smaller. The oil is pressed unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability oil circuit with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� into the oil circuit.A pressure limiting valve prevents the pressure rising above the permissible oil pressure, for example at high engine speeds.Note: Pay attention to the particular installation position when installing the oil pump. Further information is given in the Workshop Manual.Pressure limiting valveSP35_49GB19Air FilterThe air filter is part of the engine trim panel.New!Design of the air filter The air filter has been designed in such a way as to unite several tasks in a single component. In addition to the actual task of filtering the air, it also serves as the engine trim panel. As a result of this matching design features, it also makes a significant contribution to reducing structure-borne sound emissions. The main elements of the air filter are – – – top part of air filter filter element intake air connection with control flapS KOU T ODAASP35_30Viewed from belowAir outflow to throttle valve control unit J338Mount for fixtureFilter element Intake point for warm air from exhaust manifold (to control )Crankcase ventilationIntake point for cold airProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�ThermostatSP35_31Mount for fixture20GBFunction The air is inducted through the intake air connection of the air filter. This connection has two intake openings – – side opening – induction of cold air bottom opening – induction of warm airControl flap Crankcase ventilation Warm air baffle Throttle valve control unit Engine Cold airInduction of cold airFilter element Air filterA control flap resiliently mounted in the intake air connection, in combination with a thermostat, controls the quantity ratio of cold and warm intake air. This quantity ratio is controlled in line with the ambient temperature. Cold intake air is inducted out of the engine compartment downstream of the radiator. Warm intake air is inducted out of the area around the intake manifold. Intake air is heated in the intermediate area between warm air baffle and hot exhaust manifold and, when the control flap is at the corresponding position, is drawn into the intake air connection of the air filter. In the air filter, the inducted air is passed from the intake air connection to the filter element were it is filtered. The air then flows through the adjoining chamber to the throttle valve control unit.Exhaust manifoldSP35_45Control flap in intake air connectionControl flap Intake air connection to filter element Cold air ThermostatThe feed line from the crankcase ventilation is Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted also integrated in theby air filter. The air which isA. S. does not guarantee or accept unless authorised ŠKODA AUTO A. S. ŠKODA AUTO any liability Warm air to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� passed out with of respect the crankcase, is mixed with the inducted air downstream of the filter element. Induction of warm airSP35_47Control flapWarm airCold airSP35_46GB21Fuel Supply SystemThe fuel pump located in the fuel tank, pumps the fuel through the fuel filter to the injectors. A system pressure of 0.3 MPa (3 bar) is maintained in the filter. Excess fuel supplied to the engine, flows back over a short route into the fuel tank.Gravity valveService vent reservoirFuel pump Activated charcoal filterMIntake air Fuel rail Fuel filter Solenoid valve for activated charcoal filter systemInjectorSP35_02Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S.manifold does not guarantee or accept any liability Intake with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�22GBInjectorIntake manifoldSP35_11Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Inlet valveThe 4 electromagnetic injectors with their top seal are installed in the fuel rail. The injectors with their bottom seal are inserted into the intake pipe of the particular cylinder. Each cylinder is provided with an injector, which is positioned ahead of the inlet valves. The injectors are supplied with voltage through positive and actuated through earth by the engine control unit to align with their firing order. The familiar cylinder-sequential fuel injection with quick-start is used on these engines. (You can find information on the sequential fuel injection in SSP 19.)The fuel tank ventilation system operates on the familiar system. The service ventilation reservoir is part of the fuel tank. The activated charcoal filter for both engines is attached in the rear right wheel housing to the body, close to the fuel tank itself. The solenoid valve for the activated charcoal filter system is located in the right-hand side of the engine compartment. Once the engine is warm, it is actuated by the engine control unit.GB23Fuel Supply SystemThe fuel pump relay J17The fuel pump relay switches the fuel pump "ON" or "OFF".The fuel predelivery can be operated through the relay by means of a special actuation.Fuel predelivery The fuel predelivery phase is a convenience improvement when starting the engine. The fuel pump operates with the predelivery to ensure that pressure is built up in the fuel system and is already available when the engine is started. – The moment the driver's door is opened, the fuel pump relay for the feed line delivery is actuated by the door contact switch F2. The time between opening the driver's door and starting the engine is effectively used up to the commencement of main delivery (starting with the ignition/starter switch in the order of terminal +15 and "D" terminal +50).Driver's door opens Ignition "on" Engine engine starts operationF2Vehicle not moving[MPa]+15DEngine offDelivery pressureTime [s]SP35_55–If a certain period has elapsed since the driver's door was opened and ignition "on", and the engine has not yet been started, predelivery is then ended again.Driver's door opensProtected by copyright. for private The delivery is also ended if the Copying ignition is or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability switched "on", and this status exists for a with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� lengthy period, but the engine is not started! +15 F2Ignition "on", engine not startedIgnition "on", Engine engine starts operationDPredelivery is recommenced once the ignition is switched on again with the ignition/starter switch (terminal +15, "D" terminal +50). It is activated slightly before the actual starting of the engine. – The main delivery is then commenced by a signal supplied by the engine control unit.Vehicle not moving[MPa]Engine offDelivery pressureTime[s]SP35_5424GBFuel shutoff in crash (envisaged) Vehicles fitted with an airbag will subsequently feature a shutoff of the fuel feed following a crash. In this case, fuel pump relay shuts off the power supply for the fuel pump and the injectors after a crash signal is received. The crash signal is supplied by the airbag control unit over the CAN to the engine control unit. The engine control unit thereupon deactivates the fuel pump relay through "C", the power supply to fuel pump G6 is interrupted.+30 +15 D S S S SF2 TK 50 88 30 J234 J17318587 N30 N31 N32 N33 N80MG6969788896458 60Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted J537 by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability unless authorised with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�CAN-H/ACAN-L/A31SP35_12Electrical circuit of fuel supply system D F2 G6 J17 J537 N30 … 33 N80 S C Ignition/starter switch Left front door contact switch Fuel pump Fuel pump relay 4LV control unit Injectors cylinders 1 to 44 Solenoid valve for activated charcoal filter system Fuse Crash signal input = Input signal = Output signal = Battery positive = Earth = CAN/A (drive)GB25Exhaust SystemDesignExhaust manifold Lambda probe G130Warm air baffleLambda probe G39SP35_18Pre-catalytic converterMain catalytic converter Decoupling elementTo comply with the EU 4 standard, the exhaust system features 2 catalytic converters, a precatalytic converter and a main catalytic converter. The principal components of the exhaust system are – exhaust manifold with integrated catalytic converter (pre-catalytic converter) and lambda probe G39 warm air baffle/shield exhaust pipe with decoupling element, main catalytic converter and lambda probe G130Exhaust manifoldLambda probe G39– –Pre-catalytic converterA decoupling element made of a flexible metal hose is positioned in the exhaust pipe in order to absorb movements of the exhaust system and engine vibrations – – – axially laterally tilting.SP35_79Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�26GBThe pre-catalytic converterThe pre-catalytic converter is integrated in the exhaust manifold, close to the engine. This ensures that it is heated up rapidly and quickly reaches its operating temperature. (The familiar main catalytic converter is located downstream of the decoupling element in the exhaust pipe.)New!Lambda probe G39 Pre-catalytic converterWarm air baffleThe warm air baffle is positioned on the front side of the exhaust manifold. It performs the following functions: – – Collecting warm air for the air filter Heat shield for the hot exhaust manifold as a protection of adjacent components Reducing structure-borne noise emissionsWarm air to air filterSP35_19–Metal (inner) This warm air is mixed with the cold air in a Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability specific quantity ratio in the air filter, depending with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� on the operating state. Ceramic non-wovenThe warm air baffle is able to perform these functions as a result of its matching shaping and also as a result of its design. The warm air baffle is a sandwich design with an intermediate layer made of ceramic non-woven fabric.fabricMetal (outer)SP35_22GB27System OverviewSensorsEngine speed sender G28Camshaft position sender G163Throttle valve control unit J338 Angle sensor for throttle valve drive G187 and G188 Coolant temperature sender G62 Intake manifold pressure sender G71 and Intake manifold temperature sender G72 Lambda probe G39D w K ireLambda probe downstream of cat G130 Knock sensor G61 Clutch pedal switch F36 Brake light switch F and Brake pedal switch F47 Accelerator pedal position sender G79 and G185 Diagnostic connection Additional signals: Alternator terminal DF/DFM Vehicle speed signal CCS switch (ON/OFF)*Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�* on models fitted with optional equipment28rivGBeCANActuatorsEGR valve N18 with EGR potentiometer G212 4LV control unit J537 Altitude sender F96 Fuel pump relay J17 Fuel pump G6Injector N30 … 33Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted transformer unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee orIgnition accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�N152Throttle valve control unit J338 Throttle valve positioner V60Lambda probe heater Z19 Vehicle electrical system control unit J519EPCLambda probe heater downstream of cat Z29Activated charcoal filter system solenoid valve N80SP35_03GB29Engine Management SystemMagneti Marelli 4LV engine control unitThe 1.4-ltr. – 16 V 55/74 kW petrol engines are fitted with the Magneti Marelli 4LV engine management system. The control unit is attached to the bulkhead.J537Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP35_65Functions of the engine control unit – – – – – – – Cylinder-sequential fuel injection with quickstart Adaptive idle speed control Adaptive lambda control Adaptive fuel tank ventilation Adaptive exhaust gas recirculation Adaptive knock control Self-diagnosis The 4LV engine management system features a rotorless high-voltage distribution.30GBEngine speed sender G28The sender is inserted into the sealing flange at the cylinder block and attached with a bolt. It scans a 60-2 sensor gear around the circumference of which there are 58 teeth and a large gap as a reference mark, consisting of 2 missing teeth. The sensor gear is positioned on the crankshaft. The sensor is an rpm and reference mark sensor. Use of signal The signal which the engine speed sender supplies makes it possible to detect engine speed and exact position of the crankshaft. This information is used by an engine control unit in order to define the fuel injection and ignition times. Effect in the event of signal failure If no signal is received from the engine speed sender when the engine is running, the engine stops. The engine can be restarted, however. In such a case, the engine control unit switches into the emergency running mode. The control unit then calculates the engine speed and camshaft position from the information supplied by the camshaft position sender G163. As a protection for the engine, the maximum engine speed is reduced. It is still possible to restart the engine. Self-diagnosis The sender is detected by the self-diagnosis.60-2 sensor gear Reference markEngine speed sender G28SP35_59Sealing flangeElectric circuitJ537 87 82 108The following faults are stored in the fault memory: – Engine speed sender implausible signal – Engine speed sender no signal – Engine speed signal, TD, short circuit to earth – Engine speed signal, TD, short circuit to G28 positive Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP35_60GB31Engine Management SystemThe camshaft position sensor G163The camshaft position sensor operates on the Hall sensor principle. It is installed in the camshaft housing above the inlet camshaft. 3 teeth are cast onto inlet camshaft and these are scanned by the camshaft position sensor.Camshaft position sensor G163Use of signal Ignition TDC of cylinder 1 is detected on the basis of the signal supplied by the camshaft position sensor together with the signal from the engine speed sender. This information is required for the cylinderselective knock control and for the sequential fuel injection.End coverSP35_58Inlet camshaft with cast-on sensor gearCamshaft housingEffect in the event of signal failure unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedIf no signal is received from the camshaft position sensor, the engine continues running, or can also be started, respectively. The engine control unit switches into the emergency running mode. In such a case, fuel injection is then performed in parallel and no longer sequentially.Electric circuitJ537 98 86 108+oG163SP35_6132GBGeneral function A Hall voltage is generated each time a tooth moves past the camshaft position sensor. The duration of the Hall voltage corresponds to the length of the particular tooth. This Hall voltage is transmitted to the engine control unit where it is analysed. The signals can be displayed with the digital memory oscilloscope of VAS 5051.Rise in flankMagnetic field of sensorSP35_62Function of cylinder 1 recognition If the engine control unit receives a Hall voltage from the camshaft position sensor and the reference mark signal of the engine speed sender at the same time, the engine is then in the compression stroke of cylinder 1. The engine control unit counts the teeth of the engine speed sensor gear after the reference mark signal and is able to calculate from this the position of the crankshaft. Example: The 14th tooth after the reference mark equals TDC of cylinder 1.Function of quick-start recognitionThe momentary position of the camshaft relative to the crankshaft can be rapidly detected on the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised KODA AUTOto A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability basis of the three teeth. This makes by it Š possible respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� more rapidly activate initialwith combustion, and the engine starts sooner.Signal of engine speed senderSP35_63Length of signal equals length of toothSP35_64GB33Emission Control SystemPre-catalytic converter Main catalytic converterThe exhaust system features not only the familiar main catalytic converter but, in addition, a further catalytic converter, positioned close to the engine, in the exhaust line upstream of the main catalytic converter. Because it is located at some distance from the engine, the main catalytic converter requires a certain time until it reaches the operating temperature required for proper operation of the catalyst. Consequently, it is sometimes difficult to comply with the legal limit concentrations for the exhaust gas, particularly in the starting phase of the engine. A pre-catalytic converter is installed immediately downstream of the exhaust manifold in order to ensure effective emission control, also in the engine start phase. Consequently, this catalytic converter heats up very rapidly and reaches the necessary operating temperature shortly after engine start.Lambda probe G130 Lambda probe G39 Pre-catalytic converter Main catalytic converterSP35_80Standardvalid fromCO g/kmHC g/km 0.2NOx g/km 0.153 Januar 2.3 The catalytic converter is also known as the "start purposes,EU Protected by copyright. Copying for private or commercial in part or in whole, is not permitted y 2000 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability catalytic converter".with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The combined system of pre- and main catalytic converter, lambda probes and engine management system makes it possible to ensure compliance with the limits for EU 4 even today. Lambda probes There are 2 lambda probes integrated in the emission control system. Both lambda probes are characterised by their planar design (flat functional layers) of the sensor elements and differ in terms of the closed-loop control characteristic and internal structure.EU 4Januar y 20051.00.10.08Note: Emission standard EU 4 does not come into effect until the year 2005!34GBInternal structure of the sensor elements(Schematic presentation) Lambda probe G39Exhaust flow CO, NOx, HC, O2, C2H6 Exhaust pipe Protective layer Protective layer Electrode Pump cell Sensor (Nernst cell) Electrode Reference air passage Insulation Heater Insulation Heating sheetProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Lambda probe G130Exhaust flow CO, NOx, HC, O2, C2H6 Exhaust pipeElectrode Sensor (Nernst cell) Electrode Reference air passage Insulation Heater Insulation Heating sheetto catSP35_81to tail pipeSP35_82The lambda probes can scarcely be distinguished from the outside. The connectors can be used as an external characteristic. ConnectorSP35_68SP35_73Lambda probe G39 – 6-pinLambda probe G130 – 4-pinGB35Emission Control SystemLambda probe G130The lambda probe G130 is installed in the exhaust pipe downstream of the main catalytic converter. It is a planar design of lambda probe with a jump characteristic of λ = 1 (also known as a "two-point probe").Lambda probe G130Design and functionSP35_77The probe is a planar design (= flat, extended), and is manufactured from a zirconium dioxide (ZrO2) ceramic. A measuring cell and heater are integrated in the planar sensor element. A porous ceramic protective layer, which prevents damage resulting from erosion for all operating temperatures, is permanently sintered onto the sensor element. This ensures long operating life and reliable compliance with the high function demands. The heater consists of noble metal and is positioned spatially in the sensor element so as to ensure that the lambda probe heats up rapidly with a lower power consumption. The operating principle of the probe is based on the principle of a galvanic oxygen concentration cell with solid body electrolyte, consisting of ceramic sheets – also known as a Nernst cell.PTFE shaped hose PTFE grommetConnection cablesConnectorSP35_73Contact holderSensor element with heater Protective sleeveSeal setDouble protective tubeProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Note: with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Greatly simplified sectional view of the sensor element.Sensor cross section Exhaust gas Porous protective layer Us ZrO2 ceramic Us = Sensor voltage 36 Insulation layerJ537Reference air HeaterSP35_72GBThe lambda probe compares the residual oxygen concentration in the exhaust gas with the oxygen concentration in the reference air (comparative atmosphere equal to ambient atmosphere – interior of probe connected by openings to ambient atmosphere). The probe operates as a so-called "two-point probe" and merely indicates whether a rich mixture (λ 1) or a lean mixture (λ 1) is present in exhaust gas. The mixture control is then performed by the engine control unit. Each voltage jump is converted as a signal which is sent directly to the engine control unit. Depending on whether a rich or lean mixture is signalled, a richer or leaner fuel-air mixture is then produced. An exhaust temperature of at least 350 ˚C is necessary to ensure reliable closed-loop control operation of the sensor ceramic. An electric heater, integrated in the sensor, ensures optimal sensor temperatures to ensure that the sensor operates effectively even at low engine loads and low exhaust temperatures. Advantages – Short warming-up period and thus also improved emission levels in the warming-up phase – Stable control characteristic Substitute function Open-loop control mode based on mapmV 1000ab800600Sensor voltage Us4002000 0,8 0,9 1Air index λSP35_741,11,2a … rich mixture (air deficiency) b … lean mixture (air excess)Electric circuit+SG130Z29λ686963 J537SP35_75GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�37Emission Control SystemLambda probe G39Lambda probe G39 is a pre-catalytic converter probe installed in the exhaust manifold upstream of the pre-catalytic converter.Lambda probe G39As a broadband probe, it offers enlarged applications compared to the familiar "two-point probe": – constant lambda closed-loop control by means of constant signal for variation of λ = 1 – closed-loop control also for values which differ from λ = 1 (of significance, for example, for closed-loop control of lean concept petrol engines)SP35_76Design and function The probe is a planar design (= flat, extended), and is manufactured from a zirconium dioxide (ZrO2) ceramic. It differs from the two-point probe in terms of its design as a result of: – – – the inner structure of the sensor element the number of terminals at the connector and the electronic control.ConnectorSP35_68Its modular design in combination with planar technology makes it possible to integrate several functions. As an addition to the operating principle of the two-point probe, a second electrochemical cell, pump cell, is integrated in the broadband lambda probe, in addition to the oxygen concentration cell (Nernst cell).Exhaust gasSensor element with heaterIp + UrefUs ∼ IpPump cell Measuring gap Reference air passageJ537SP35_67Note: Greatly simplified sectional view of the sensor element.Heater Nernst cell Us Uref IpControl electronics… Sensor voltage … Reference voltage … Pump current38Protected by copyright. Copying for private or commercial purposes, in part or in whole, is GB not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The closed-loop control of the probe is performed by the engine control unit and comprises – closed-loop control of the oxygen pump cell and oxygen concentration cell – generation of the sensor signal – temperature control of the probe The exhaust gas flows through a small hole in the pump cell into the measuring gap of the Nernst cell. The voltage applied to the probe is controlled in such a way as to maintain the gas composition in the measuring gap at a constant λ = 1. In this case, depending on the oxygen composition (oxygen-rich = lean/oxygen-poor = rich), oxygen ions are "pumped" out of the measuring gap, or into the measuring gap, respectively. The resulting pump flow is a measure for the air index λ in the exhaust gas. Depending on the exhaust composition, the probe transmits a matching signal to the engine control unit. The engine control unit now determines whether it is necessary to produce a richer mixture (by adding fuel) or a leaner mixture (by reducing the fuel quantity). An electric heater integrated that the minimum required operating temperature of 600 ˚C is always maintained. Substitute function Open-loop control mode based on map. Advantages – More dynamic closed-loop control as variation from set value is up-to-date and is available as the concrete value – Possibility of controlling any desired set values, in other words also values which differ from λ = 1Pump flow IpmA 3,0 2,0 1,0ab0 – 1,0 – 2,0 0,7 1,0 1,3 1,6 1,9 2,2Air index λSP35_69a - rich mixture (air deficiency) b - lean mixture (air excess)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability inwith the probe ensures respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Electric circuit+SG39Z19λNote: Refer to SSP 39 (EOBD) for a more detailed description.52 71 51 70 5 J537SP35_70GB39Exhaust Gas Recirculation SystemFunction diagramAir filter Intake manifold Engine control unitJ537N18Exhaust gas recirculation valve Feed line to intake manifoldt °C n 1/min p MPaEngine loadSP35_05Already during normal moment of valve overlap, a certain quantity of residual gas is displaced from the combustion chamber into the intake manifold. During the subsequent intake phase, a portion of residual gas is then inducted also in addition to the fresh mixture.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted TheAUTO exhaust gas through two holes engine operation at the unless authorised by ŠKODA AUTO A. S. ŠKODA A. S. does not flows guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�positioned at right angles to the inducted air flow, directly into the middle of the fresh air flow below the throttle valve in order to achieve the best possible uniform distribution of the recirculated exhaust gas with the inducted fresh air. The EGR valve is operated by the 4LV engine control unit J537 in line with a defined map. Information processed for this includes engine speed, engine load, atmospheric pressure, coolant temperature. A potentiometer signals the opening cross section to the engine control unit. If the exhaust gas recirculation system is activated, the maximum quantity of exhaust gas is limited to 18 % of the inducted air quantity. No exhaust gases are recirculated in the idling speed range, when decelerating and during the engine warming-up phase. Exhaust gas recirculation in combination with the specifically optimised design of the inlet ports and combustion chamber, ensures good part load fuel consumption levels.Up to a certain quantity, residual gas (exhaust gas) can have a positive impact on reducing the formation of oxides of nitrogen and in achieving improved energy conversion (reduction in fuel consumption). With the additional recirculation of the exhaust gases, the NOx (oxides of nitrogen) emission in both engines is further reduced and fuel consumption improved. This is done by extracting a certain quantity of exhaust gas from the engine exhaust and passing it through the exhaust gas recirculation valve to the inducted air. This principle is known as "external" exhaust gas recirculation.40GBThe electrically operated exhaust gas recirculation valveNew!EGR valveFeed line to intake manifoldExhaust manifoldSP35_06The exhaust gas recirculation valve is an electrically directly actuated valve. Compare this with the diesel engine – solenoid valve actuated electrically, exhaust gas recirculation valve operated pneumatically – SSP 22. The valve is flanged directly to the cylinder head and has a direct link over a passage in the cylinder head to the exhaust passage of cylinder 4.The valve is connected to the intake manifold by means of a stainless steel line. As a result of being flanged directly to the cylinder head, the valve is cooled indirectly by the cooling circuit of the engine, which has a favourable effect on the electrical components.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB41Exhaust Gas Recirculation SystemThe function If the exhaust gas recirculation valve is deenergised, it shuts off the return flow of exhaust gases to the intake manifold. It is switched on from a certain coolant temperature. When the solenoid is excited, the valve is pressed off its seat and opened. The exhaust gas recirculation system is controlled in line with the map stored in the engine control unit.ArmaturePotentiometerInput information used for this purpose includes, – – – – information on engine speed information on engine load coolant temperature atmospheric pressureCoilExhaust gas from enginePressure balance to air filterA potentiometer is integrated in the head of the valve. This potentiometer detects the opening cross section of the valve and signals this as a feedback signal to the engine control unit, whereupon the voltage of the solenoid in the valve is controlled in line with the map. A direct link exists to the ambient air pressure through the air filter in order to ensure a pressure balance in the valve during the control phases.Valveto intake manifoldSP35_07Self-diagnosis Electric circuit The valve has a diagnostic capability.+15 J537 114 100 98 108The following information is stored in the fault memory: – – – zero point displacement maximum opening maximum travelSIn addition, self-diagnosis also detects a valve which jams.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�N18SP35_0842GBSaving fuel by recirculating exhaust gasThe exhaust gas recirculation system operates in the part load range of the engine, in other words when the throttle valve is only slightly open. On an engine fitted with an exhaust gas recirculation, however, the throttle valve must be opened further than on an engine without exhaust gas recirculation, for the same power output.Without exhaust gas recirculation Example: Engine speed = 3000 rpm Throttle valve angle = αAt a throttle valve angle of = α the inducted air is subjected to severe swirling at the throttle valve. In view of this swirling, the engine has to overcome a greater resistance when inducting the air. The fuel consumption is increased as a result of these throttling losses.With exhaust gas recirculation Example: Engine speed = 3000 rpm Throttle valve angle = βSP35_09On an engine fitted with exhaust gas recirculation, exhaust gases are mixed with the inducted air. The throttle valve must be opened further, however, to ensure that the same quantity of fresh air is inducted as on an engine without exhaust gas recirculation. As a result of this larger throttle valve angle = β, the air is subjected to less swirling at the throttle valve. The engine is able to induct the air with a reduced level of resistance. The consequence is an improvement in fuel consumption.SP35_10GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 43 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Function Diagram+30 +15SSSSSSSD/ +15J17 N30 N31 N32 N33 F36 FMF47+ 65 A 114 100 98 86 85 109 87 82 108 96 97 88 89 39 55 56-+ F2oN18 G212 G163 G72 G71 G28Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�3144For legend of function diagram ⇒ page 46GBJ519+30 +15SSSSSK Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�N80G79G185G39Z19G130Z29λλ6436 35 73 72 34 33 J53752 71 51 70 568696358CAN - HCAN - L60433493118 117 928381 9199 10628765412102 103G62+ MJ338 V60 G188 G187 G61ABCN152G6I IV II IIIMQ P31inGBoutSP35_0145Function DiagramLegend of function diagramComponents Colour coding/Legend A Battery = Input signal F Brake light switch F2 Door contact switch – driver side = Output signal F36 Clutch pedal switch F47 Brake pedal switch = Battery positive G6 Fuel pump G28 Engine speed sender = Earth G39 Sonde Lambda G61 Knock sensor I = bi-directional G62 Coolant temperature sender G71 Intake manifold pressure sender = Diagnostic connection G72 Intake manifold temperature sender G79 Accelerator pedal position sender G130 Lambda probe downstream of cat G163 Camshaft position sender G185 Sender 2 for accelerator pedal position Additional signals Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA sender AUTO A. S. 1 ŠKODA AUTO A. S. does not guarantee or accept any liability G187 Angle for throttle valve drive with respect to the correctness of information in this document. Copyright by ŠKODAA AUTO A. S.� Alternator terminal DF/DFM (electric throttle control) G188 Angle sender 1 for throttle valve drive B CCS switch (ON/OFF)* (electric throttle control) G212 Exhaust gas recirculation C Vehicle speed signal potentiometer J17 Fuel pump relay J285 Control unit in dash panel insert CAN-BUS H = J338 Throttle valve control unit Drive databus J519 Vehicle electrical system control unit CAN-BUS L = J537 4LV control unit M Brake light bulb N18 Exhaust gas recirculation valve N30 … 33 Injectors, cylinders 1 … 4 N80 Activated charcoal filter system solenoid valve * on models fitted with optional equipment N152 Ignition transformer P Spark plug connector Q Spark plugs V60 Throttle valve positioner Z19 Lambda probe heater Z29 Lambda probe 1 heater, downstream of catalytic converter}The function diagram represents a simplified current flow diagram. It provides information on the links of the Magneti Marelli 4LV engine management system for engines with code letters AUA and AUB.46GBSelf-DiagnosisThe control unit of the Magneti Marelli 4LV engine management system is equipped with a fault memory. All the parts of the system marked in colour, are monitored by the self-diagnosis. The self-diagnosis can be performed with the vehicle system tester V.A.G 1552, the fault reader V.A.G 1551 or with the vehicle diagnosis, measuring and information system VAS 5051. Self-diagnosis is initiated with the address word 01 - Engine electronicsEPCThe following functions are possible:SP33_7801 - Interrogating control unit version 02 - Interrogating fault memory 03 - Final control diagnosis 04 - Basic setting 05 - Erasing fault memory 06 - Ending output 07 - Coding control unit 08 - Reading measured value block 15 - Readiness codeProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted The function 04 AUTO – Basic setting unless authorised by ŠKODA A. S. ŠKODA AUTOmust A. S. does not guarantee or accept any liability with to theout correctness of replacing information in this document. Copyright by ŠKODA AUTO A. S.� be respect carried after theNote:engine control unit, the throttle valve control unit, or the engine, and after disconnecting the battery. Recommend your customer that if he replaces the battery himself or disconnects and re-connects the battery, to have a basic setting carried out subsequently in a workshop.1 4 7 C O 8 Q 52 6 93HELPV.A.G. 1552SP33_73 SP33_43You can find the individual fault codes in Workshop Manual 1.4/55; 1.4/74 Engine – Fuel Injection.GB47Self-DiagnosisReadiness code The readiness code is an 8-digit numerical code which displays the status of the diagnosis steps of relevance to the exhaust system. These diagnoses are performed at regular intervals during normal driving.1 4 7 8 O Q 5 9HELP2 63The readiness code does not provide any information of whether the faults exist in the system. It provides statements regarding the status of the particular diagnosis: 0 - Diagnosis has been ended 1 - Diagnosis has been interrupted or - was not yet carried out or - could not yet be carried out.CV.A.G. 1552SP33_73 SP33_43If the fault memory of the engine control unit is erased, the readiness code is then automatically set to "0".The readiness code can be read out using the Protected by copyright. Copying for private or commercial purposes, V.A.G diagnostic testers by selecting address Use the current software status,in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability word "01" and function "15", and also be with respect to the of information in this document. Copyright by ŠKODA AUTO A. S.� 5 correctness or higher for V.A.G 1552, generated using special routines. 8 or higher for V.A.G 1551.Note: Information on generating and reading the readiness code can be found in the Workshop Manual 1.4/55; 1.4/74 Engine – Fuel Injection.Meaning of an 8-digit numerical block for readiness codeThe readiness code is generated only if all display places are 0.12345678 0 Catalytic converterDiagnosis function0 0 0 0 0 0 0Catalytic converter heater (no diagnosis at present/always "0") Activated charcoal filter system (fuel tank ventilation system) Secondary air injection system (not present/always "0") Air conditioning (no diagnosis at present/always "0") Lambda probes Lambda probe heater Exhaust gas recirculation48GBTest Your KnowledgeWhich answers are correct? Sometimes only one. But, perhaps also more than one – or all! Please complete the missing entries.?1.What are the advantages of operating the valves using roller rocker fingers? A. B. C. reduced level of friction. reduced force required by the engine. there is no further valve play to compensate.2.What is correct? A. B. C.The engine speed sender G28 is inserted into the sealing flange at the cylinder block and secured with a bolt. The engine speed sender G28 is installed in the cylinder block and is only accessible after removing the oil pan. The engine speed sender G28 is inserted into the cylinder block from the outside.3.The fuel pump relay A. B. C.switches the fuel pump on. switches the fuel pump off. activates the fuel after-delivery.4.The pre-catalytic converter A. B. C.protects the main catalytic converter. pre-cleans the exhaust gas to allow the main catalytic converter to operate more effectively. heats up very rapidly because it is installed close to the engine and is therefore also able to carry out its function during the engine start phase.?Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB49