TECHNICAL DOCUMENTATION
SSP 971603 Audi Data Bus Technologies

This PDF is currently unavailable.
Read document text
Service TrainingVAS 5052Vehicle Diagnosis and Service Information System Version -D- / V01.02 20/08/2001Vehicle SelfDiagnosisElsa WinApplicationsAdministrationPrintHelpAudi Data Bus TechnologiesCourse Number 971603Audi of America, Inc. Service Training Printed in U.S.A. Printed 12/2005 Course Number 971603©2005 Audi of America, Inc.All rights reserved. All information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher.All requests for permission to copy and redistribute information should be referred to Audi of America, Inc.Always check Technical Bulletins and the latest electronic repair information for information that may supersede any information included in this booklet.Trademarks: All brand names and product names used in this manual are trade names, service marks, trademarks, or registered trademarks; and are the property of their respective owners.2Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 CAN-bus Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 CAN-bus Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Data Bus On Board Diagnostic Interface . . . . . . . . . . . . .20 CAN-bus Fault Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Other Data Bus Technology. . . . . . . . . . . . . . . . . . . . . . . . .44 LIN Data Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Fiber-Optic Data Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Bluetooth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 Diagnosis CAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Appendix B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121The Self-Study Program provides introductory information regarding the design and function of new models, automotive components or technologies. The Self-Study Program is not a Repair Manual! All values given are intended as a guideline only and refer to the software version valid at the time of publication of the SSP. For maintenance and repair work, always refer to the current technical literature.ReferenceNoteiNotesiiIntroductionData Bus TechnologyThe demand for more luxury features and increased comfort in vehicles creates an ever-increasing need for more capable and more complicated vehicle electronic systems. Data bus technology makes it possible to form a complex network of electronic control modules and sensors that can communicate with each other and share data across the entire network without the size, complexity, expense and other limitations of a conventional wiring harness. Audi’s introduction of Controller Area Network or CAN data bus technology in the mid-’90s was a first, important step toward the exchange of increasing amounts of data between control modules. The first portion of this Self-Study Program describes basic functions of CAN-bus systems in general, and goes on to cover specific functions, diagnosis and testing for Drivetrain, Convenience and Infotainment CAN bus systems. The latter portion of this Self-Study Program describes the single wire Local Interconnect Network (LIN) data bus, Media Oriented Systems Transport (MOST) fiber-optic data bus, and wireless data transmission technology used in the latest Audi vehicles.Purpose of a CAN-bus SystemThe CAN-bus system provides the following advantages as an overall system: – Data exchange between control modules takes place on a uniform platform or protocol, with the CAN-bus acting as a data highway – Systems involving several control modules, ESP for example, can be implemented efficiently – System expansions and additions of optional extras are easier to implement – CAN is an open system that permits adaptation to various data transfer media, such as copper wires or fiber-optic cables – CAN is used for control module diagnosis, replacing the actual K-wire with a so-called virtual K-wire – System-oriented diagnosis is possible across systems employing several control modules1CAN-bus OverviewCAN-bus Networking in Audi VehiclesDepending on the model year, different CAN-bus systems are used in Audi vehicles. The first, introduced in the mid-’90s, was a Convenience CAN with a data transfer rate of 62.5 kbits/s (kilobits per second). Next came a Drivetrain CAN using a data transfer rate of 500 kbits/s. As of model year 2000, more advanced Convenience and Infotainment CAN systems have been introduced, each with a data transfer rate of 100 kbits/s. Additional types of data bus systems, introduced in model year 2004, are covered in this Self-Study Program. The Convenience and Infotainment CAN systems exchange data with the Drivetrain CAN through the Gateway, which allows for communication between bus systems operating at different data transfer rates.Drivetrain CAN Network with Three Control ModulesSensorABS Control ModuleEngine Control ModuleInstrument ClusterActuator2CAN-bus OverviewDesign and Main FeaturesIndividual electronic control modules are connected in parallel through the CAN-bus system. This results in the following requirements for the design of the overall system: – High level of error protection: transmission interference caused by internal or external sources must be detected with a high degree of certainty – High availability: if a control module fails, the rest of the system must continue to function as well as possible in order to continue the exchange of information – High data density: all control modules have the same information status at all times. This means there is no difference in data between the control modules. In case of faults anywhere in the system, all the connected users can be informed with equal certainty. – High data transmission rate: data exchange between networked users must be very fast in order to meet real-time requirementsPractical LayoutDue to different demands with respect to the required repeat rate of the signals, the volume of data and its availability (readiness), the three CAN systems used since model year 2000 are configured as follows: Drivetrain CAN (high speed) at 500 kbits/s networks the control modules in the drivetrain systems. Convenience CAN (low speed) at 100 kbits/s networks the control modules in the convenience system. Infotainment CAN (low speed) at 100 kbits/s networks the information and entertainment systems — radio, telephone and navigation, for example.Signals are sent over the CAN system digitally. Secure transmission is possible at rates of 1000 kbits/s (kilobits per second) or more, as seen in the latest Infotainment network. Some CAN systems are fixed at lower data transmission rates to ensure signal quality.Note Transmission rates of 1,000 kbits/s and higher are used in the latest Infotainment CAN networks, which are covered later in this Self-Study Program.3CAN-bus OverviewCommon to All CAN-bus Systems:– Systems are all subject to the same regulations for data exchange, such as the defined transfer protocol – To assure a high degree of protection from electro-magnetic interference and prevent radiation emission, each CAN-bus is made up of entwined twoconductor wiring referred to as a twisted pair – Signals to be sent are stored in the transceiver of a sending control module with different signal levels before being sent to both CAN lines. Not until the differential amplifier of the receiving control module calculates the difference of both signal levels is a single, cleaned signal sent to the CAN receiver of the control module – First examples of the Infotainment CAN have the same properties as the Convenience CAN. In some models, they are operated through one common pair of wires (bus). In newer vehicles, we will see optical bus systems for the Infotainment networkMain Differences Between CAN-bus Systems:– Drivetrain CAN is switched OFF by terminal 15 following an after-run period – Convenience CAN is supplied with power through terminal 30, and must remain on standby. To prevent excessive electrical load, the system switches to sleep mode by switching terminal 15 OFF when it is not required – Convenience/Infotainment CAN remains operational, thanks to the second wire, if there is a short circuit in the data bus or an open circuit in a CAN wire. In such an instance, the system will switch automatically to single wire operation – Electrical signals from the Drivetrain CAN and Convenience/Infotainment CAN are differentWarning! The Drivetrain CAN should never be electrically connected to the Convenience/ Infotainment CAN! The various data bus systems for Drivetrain and Convenience/ Infotainment networks should only be connected in the vehicle through the Gateway. The Gateway may be integrated with an existing control module or installed as a separate Gateway control module.4CAN-bus OverviewCAN-bus ComponentsThe CAN-bus is made up of a controller, a transceiver and two data bus lines. Apart from the data bus lines, the components are located in the electronic control modules. The main functions of the control modules are the same as before, with the following additional tasks:CAN TransceiverThe CAN transceiver is a combined transmitter and receiver. It converts the data that the CAN controller supplies into electrical signals, sending this data over the data bus lines. Likewise, it receives data and converts this data for the CAN controller.CAN ControllerThe CAN controller receives transfer data from a micro-computer integrated into the control module. The CAN controller processes this data and relays it to the CAN transceiver. Likewise, the CAN controller receives data from the CAN transceiver, processes it, and relays it to the elctronic control module micro-computer.Data Bus LinesThe data bus lines are bi-directional and transfer data. They are referred to as CAN-high and CAN-low.Motronic Engine Control Module (ECM) J220 with Integrated CAN Controller and CAN TransceiverTransmission Control Module (TCM) J217 with Integrated CAN Controller and CAN TransceiverData Bus Lines5CAN-bus OverviewCAN-bus TopologyA special feature of Audi’s CAN-bus design is the tree-like connecting structure for the control modules. This structure allows optimal connection of the control module wiring. The actual layout of the CAN wiring in a vehicle is referred to as CAN topology and is vehicle-specific.Instrument Cluster Control Module J285Distance Regulation Control Module J428Data Bus On Board Diagnostic Interface J533 16-Pin Connector T16NOX Sensor Control Module J583Engine Control Module (ECM) J623Driver’s Door Control Module J386Energy Management Control Module J644Rotation Rate Sensor G202ABS Control Module J104Front Passenger’s Door Control Module J387Auxiliary Heater Control Module J364Seat Occupied Recognition Control Module J706Airbag Control Module J234Left Rear Door Control Module J388Parking Aid Control Module J446Transmission Control Module (TCM) J217 Left Headlamp Power Output Stage J667 Electrical Drive Main Relay J437 Right Headlamp Power Output Stage J668 Electro-Mechanical Parking Brake Control Module J540Right Rear Door Control Module J389Vehicle Electrical System Control Module J520Memory Seat/ Steering Column Adjustment Control Module J136Access/Start Control Module J518Passenger Memory Seat Control Module J521Vehicle Electrical System Control Module J519Level Control System Control Module J197Towing Recognition Control Module J345Comfort System Central Control Module J393Steering Angle Sensor G85Steering Column Electronic Systems Control Module J527Climatronic Control Module J255Multi-Function Steering Wheel Control Module J453Tire Pressure Monitoring Control Module J5026CAN-bus OverviewTelephone Transceiver R36Front Information Display Control Head Control Module J523Telephone/Telematics Control Module J526Telephone Handset R37Data Bus On Board Diagnostic Interface J533Navigation System with CD Drive Control Module J401TV Tuner R78 CD Changer R41Digital Sound System Control Module J525Radio RSpeech Input Control Module J507MOST BusInstrument Cluster CANDiagnosis CANDrivetrain CAN Access/Start Authorization Switch E415 Keyless Access Authorization Antenna Reader J723Convenience CANDistance Control CAN Wiper Motor Control Module J400 Rain/Light Recognition Sensor G397LIN BusVarious Sub-Bus Systems Interior Monitoring Sensor G273Alarm Horn H12Wireless Transmission — Bluetooth SignalFresh Air Blower Control Module J126A/C Pressure/ Temperature Sensor G395Left Front Tire Pressure Monitoring Transmitter G431Right Front Tire Pressure Monitoring Transmitter G432Left Rear Tire Pressure Monitoring Transmitter G433Right Rear Tire Pressure Monitoring Transmitter G434Rear Tire Pressure Monitoring Antenna R967CAN-bus OverviewBasic Information ExchangeInformation is exchanged between control modules in small packages of data referred to as messages. Any control module can send or receive messages. A message contains information about physical values such as engine speed (RPM) or engine coolant temperature. Engine speed in this case is represented as a binary value (a string of ones and zeroes). For example: engine speed of 1800 RPM is represented as 00010101 in binary notation. Before being sent, the binary value is converted into a serial bit stream. The bit stream is sent over the TX line (transmit line) to the transceiver (amplifier). The transceiver converts the bit stream into voltage values, which are then sent over the bus line one by one. In the reception process, voltage values are converted back into a bit stream by the transceiver and sent over the RX line (receive line) to the control module. The control module then converts the serial binary values back into messages. For instance: the value 00010101 is converted back to the engine speed value of 1800 RPM. A message sent to the CAN-bus can be received by any control module, and is generally received and evaluated by all other electronic control modules on the particular CAN-bus. This process relies on what is called the broadcast principle — one sends, everyone receives. The idea is derived from a radio transmitter broadcasting a program that any tuner (receiver) can receive. The broadcasting process ensures that all control modules connected to the CAN-bus have the same information status.Note For more on basic information exchange, please see Appendix A.Broadcast Principle: One Sends, Everyone Receives8CAN-bus OverviewData Transfer ProcessSupplying the DataThe control module provides data to the CAN controller for transfer.Checking DataControl modules check whether or not they require the data they have received for their functions.Sending DataThe CAN transceiver receives data from the CAN controller, converts it into electrical signals, and sends them.Accepting DataIf the received data is important, it is accepted and processed. If not, it is ignored.Receiving DataAll other control modules networked with the CAN-bus become receivers.Control module 1 Accept data Check data Receive dataControl module 2 Provide dataControl module 3Control module 4 Accept dataCheck data Send data Receive dataCheck data Receive dataData bus linesIf more than one control module wants to send its data protocol simultaneously, the system must decide which control module comes first. Priorities are determined and the data is assigned a “high” or “low” weighting depending on importance by changing a data bit to 1 (one) or 0 (zero). The data protocol with the highest priority is sent first. For safety reasons, the data protocol supplied by the ABS/EDL control module is more important than the data protocol supplied by the transmission control module.9When control modules start sending their data protocol simultaneously, they compare the data bit by bit on the data bus line. If a control module sends a “low” weighting bit and detects a “high” weighting bit, the control module stops sending and becomes a receiver.CAN-bus OverviewWhat Does the CAN-bus Transfer?The CAN-bus transfers data between control modules at short intervals using a standardized data protocol, which is subdivided into seven areas. The data protocol is made up of a long string of bits. The number of bits in the data protocol depends on the size of the data field. The diagram below shows the format of the data protocol. This format is identical on both data bus lines. For the sake of simplicity, we will sometimes focus on only one data bus line in this Self-Study Program.Note A bit is the smallest unit of information (one circuit state per unit of time). In electronics, this information can only have the value “0” or “1” meaning, for example, “yes” or “no.” For a more indepth description of the data bit, please see Appendix B.Start field (1 bit) Status field (11 bits) Unused field (1 bit) Data field (maximum of 64 bits) Confirmation field (2 bits)Check field (6 bits) Safety field (16 bits) End field (7 bits)10CAN-bus OverviewHow is the Data Protocol Produced?The data protocol is made up of a string of several bits. Each bit can only have a status or value of “0” or “1.” A light switch circuit provides a simplified example of how a “0” or “1” status is generated. A switch in the circuit switches a light ON or OFF. This means that the circuit can have two different states. In principle, the CAN-bus functions in exactly the same way. Operation of a CAN transceiver is also based on two different bit states.CAN transceiverCAN transceiverStatus of Light Switch Circuit with Value “0”– Switch OPEN – Light is OFFStatus of Bit with the Value “1”– Transceiver OPEN, switched to positive voltage (approximately 5.0 volts in the Convenience CAN, for example) – Voltage is applied to the data bus lineStatus of Light Switch Circuit with Value “1”– Switch CLOSED – Light is ON5 Volts0 VoltsStatus of Bit with the Value “0”– Transceiver CLOSED, switched to Ground – Approximately 0 volts applied to the data bus line5 Volts0 Volts11CAN-bus OverviewElectrical/Electronic Properties of Data TransferVoltage Differences in CAN Wires When Changing Between Dominant and Recessive StateElectrically, data transfer is based on the difference between CAN-high voltage and CAN-low voltage. In a rest state, when there is no data transfer, both CAN-bus wires (CAN-high and CAN-low) have the same default signal level. On the Drivetrain CAN, for instance, this level is approximately 2.5 volts. The rest state is also known as the recessive state, as it can be changed by any control module connected into the network. In the active or dominant state, voltage of the CANhigh wire increases by a predetermined value (on the Drivetrain CAN, this is at least 1 volt). The voltage of the CAN-low wire drops by the same increment. This results in a rise in the voltage of the CAN-high wire to at least 3.5 volts (2.5 volts + 1 volt = 3.5 volts), and a drop in the voltage of the CAN-low wire to a maximum of 1.5 volts (2.5 volts - 1 volt = 1.5 volts). The voltage difference between CAN-high and CAN-low in a recessive state is 0 volts. In a dominant state, the difference is at least 2 volts.Signal Pattern of the Drivetrain CAN (Example)In a dominant state, the CAN-high wire rises to approximately 3.5VIn a recessive state, the two wires are at approximately 2.5V (rest state)In a dominant state, the CAN-low wire drops to approximately 1.5V12CAN-bus OverviewHow is Data Transferred?The CAN-bus is wired in parallel with all of the control modules included in the respective CAN system. The two wires CAN-high and CAN-low, are assembled as a twisted pair.The CAN wires in the wiring harness are colored orange. The CAN-high wire in the Drivetrain CAN has an additional black marking (orange/black). On the Convenience CAN, the additional color is green; on the Infotainment CAN it is violet. The CAN-low wire is always marked brown (orange/brown). For reasons of clarity, the CAN wires are shown in this Self-Study Program as completely yellow or completely green, as in a VAS scan tool digital storage oscilloscope (DSO) display. The CAN-high wire is always displayed as yellow, while the CAN-low wire is always displayed as green.Representation of CAN-High and CAN-Low Wires as Twisted PairCAN-High WireCAN-Low WireNote For more on basic information exchange, please see Appendix A.13CAN-bus SystemsProperties and Special Features of the Drivetrain CANThe Drivetrain CAN, operating at a data transfer rate of 500 kbits/s, serves as a means of networking the various control modules for the drivetrain. Examples of control modules on the Drivetrain CAN are: – Engine control module – ABS control module – Transmission control module – Airbag control module – Instrument cluster The Drivetrain CAN is, like all CAN wires, a twisted pair. It has a data transfer rate of 500 kbits/s. For this reason, it is also referred to as a high speed CAN. Data is exchanged between the control modules through the CAN-high and CAN-low wires of the Drivetrain CAN. Data messages are sent from the control modules with a repeat rate that is generally in a range of 10–25 ms. The Drivetrain CAN is activated through terminal 15 (ignition). When the ignition is switched OFF, the Drivetrain CAN is powered during a short after-run period, then completely deactivated. If either of the wires of the Drivetrain CAN fail due to an open circuit, short circuit or short circuit to battery positive, the Drivetrain CAN will not transmit data. The Drivetrain CAN, unlike the Comfort/Infotainment CAN, will not operate in single wire mode.Signal Pattern of the Drivetrain CANIn a dominant state, the CAN-high wire rises to approximately 3.5VIn a recessive state, the two wires are at approximately 2.5V (rest state)In a dominant state, the CAN-low wire drops to approximately 1.5V14CAN-bus SystemsSignal Pattern of the Drivetrain CANThe diagram below shows the pattern of a real CAN signal, recorded with the digital storage oscilloscope (DSO) from a VAS scan tool. The combined signal pattern indicates the recessive level of 2.5 volts. The dominant voltage at CAN-high is approximately 3.5 volts. At CAN-low it is approximately 1.5 volts.Freeze FrameTest Cursor Channel AAmplitude Channel AAmplitude Channel BTime ValueCursor 1Trigger PointTest Cursor Channel BDominant and recessive levels alternate UCAN high at 3.48V, UCAN low at 1.5V Setting: 0.5/Div., 0.02ms/Div.15CAN-bus SystemsProperties and Special Features of the Convenience/Infotainment CANThe Convenience/Infotainment CAN, operating at a data transfer rate of 100 kbits/s, serves as a means of networking the various control modules associated with the convenience and infotainment systems. Examples of control modules on the Convenience/ Infotainment CAN are: – Climatronic control module – Door control modules – Radio/Navigation display control module The Convenience/Infotainment CAN is, like all CAN-bus wires, a twisted pair and has a data transfer rate of just 100 kbits/s, which is why it is also referred to as a low speed CAN. Data is exchanged between the control modules through the CAN-high and CAN-low wires of the Convenience/Infotainment CAN. The Convenience CAN and Infotainment CAN can be operated on a common pair of CAN-high and CAN-low wires because the two systems have the same transfer rate. On later models, Infotainment data is also transferred on an optical bus.Signal Pattern of the Convenience/Infotainment CANIn a dominant state, the CAN-low wire drops to approximately 1.4VIn a recessive state, the CAN-high wire is at approximately 0V and the CAN-low wire is at approximately 5VIn a dominant state, the CAN-high wire is at approximately 3.6V16CAN-bus SystemsDifferential Data Transfer on the Convenience/Infotainment CANIn order to provide greater resistance to electromagnetic interference and reduced power consumption on the low speed CAN, the Convenience/Infotainment CAN is different from the Drivetrain CAN in some key ways. First, the CAN-high and CAN-low signals are independent. This was accomplished using independent drivers (output amplifiers) in the electronic control modules. The CAN-high and CAN-low wires of the Convenience/ Infotainment CAN are not connected to each other through resistors. They no longer influence each other, but work independently. There is no common medium voltage. The CAN-high signal is 0 volts in a recessive state (rest state), and greater than or equal to 3.6 volts in a dominant state. For the CAN-low signal, the recessive level is 5 volts and the dominant level is less than or equal to 1.4 volts. After differential build-up in the differential amplifier, the recessive level is 5 volts and the dominant level is 2.2 volts. The combined difference in voltage between the recessive and dominant levels (voltage rise) is therefore greater than or equal to 7.2 volts.Signal Pattern Image on VAS 5051 DSO (Freeze Frame)For reasons of clarity, displays of the CAN-high and CAN-low signals are separated. This is indicated by the different zero points in the DSO image. The different rest states for CAN-high and CAN-low are clearly visible. The much greater voltage rise (7.2V) is noticeable compared to the Drivetrain CAN.Dominant and recessive levels alternate UCAN high at 3.6V, UCAN low at 1.4V Setting: 2V/Div., 0.1ms/Div.17CAN-bus SystemsCAN Transceiver on the Convenience/Infotainment CANA CAN transceiver connected to and operating on the Convenience/Infotainment CAN works much the same way as a transceiver on the Drivetrain CAN. The only differences are that different signal levels are sent, and measures are taken to revert to CAN-high or CAN-low alone if there is a fault (single wire operation). Short circuits are still detectable between CAN-high and CAN-low and, in the case of a fault, the CAN-low driver is switched OFF. If this happens, CAN-high and CAN-low wires have the same signal. The data transfer of data on the CAN-high and CAN-low wires is monitored by the fault logic system integrated into the transceiver. The fault logic system evaluates the input signals of both CAN wires. If there is a fault, such as an open circuit in one CAN wire, it will be detected by the fault logic system and only the intact wire is used by the control module for CAN by evaluation (single wire operation). For normal operation, the CAN-high signal “minus” CAN-low is evaluated. The effects of simultaneous disturbances in both wires of the Convenience/ Infotainment CAN are thereby minimized as effectively as on the Drivetrain CAN.Design of Convenience/Infotainment CAN TransceiverPossible Signal Level at the Differential Amplifier OutputRX Wire (Control Module Receiver Wire)CAN-High AmplifierFault Logic SystemTransceiverCAN-Low Amplifier Differential AmplifierCAN-High Wire Twisted Pair CAN-Low Wire18CAN-bus SystemsConvenience/Infotainment CAN in Single Wire OperationIf either of the CAN wires of the Convenience CANbus fails due to an open circuit, short circuit or short circuit to battery positive, the system switches to single wire operation. During single wire operation, only the signals of the remaining intact CAN wire are evaluated. In this way, the Convenience/Infotainment CAN remains operational. The actual CAN evaluation in the control module is unaffected by single wire operation. Using a special fault output, the control module provides information as to whether the transceiver is in normal or single wire operation.Signal Pattern on DSO During Single Wire Operation (Freeze Frame)19Data Bus On Board Diagnostic InterfaceData Bus On Board Diagnostic Interface J533 (Gateway) NetworkingThe Drivetrain CAN cannot be connected directly to the Convenience/Infotainment CAN due to the different signal levels and resistance levels. In addition, the different data transfer rates of the various data bus systems make it impossible for control modules to evaluate the different signals. Conversions are necessary to allow the different data bus systems to communicate with each other. These conversions are carried out by Data Bus On Board Diagnostic Interface J533, also known as the Gateway.Tram (Convenience/ Infotainment CAN)Platform B Boarding and Exiting PassengersBoarding and Exiting Passengers Platform AFast Train (Drivetrain CAN)The principle of the Gateway can be compared to a railway system. At platform A (the Gateway) of the railway, a fast train arrives (Drivetrain CAN, 500 kbits/s) with several hundred passengers on board. At platform B, a slower train is already waiting (Convenience/Infotainment CAN, 100 kbits/s). A number of passengers change from the fast train to the slower train and some passengers from the slower train have transferred to the faster train.The function of the railway platform is to allow the passengers to change trains to take them to their chosen destination at different speeds. This describes the role of the Gateway in networking. The main role of the Gateway is to exchange information between both systems at different speeds.20Data Bus On Board Diagnostic InterfaceOn earlier model year Audi vehicles, J533 was located inside Instrument Cluster J285 and was accessible through VAS scan tools using Address Word 17. Gateway J533Diagnosis System21Data Bus On Board Diagnostic InterfaceOn later model year Audi vehicles, J533 is a separate control module which can be addressed through VAS scan tools using Address Word 19.Instrument Cluster CAN 500 kbits/s Diagnosis CAN 500 kbits/sMOST Bus 21 Mbits/s (Optical)Drivetrain CAN 500 kbits/sAdaptive Cruise Control CAN 500 kbits/s (Optional) Convenience CAN 100 kbits/s Data Bus On Board Diagnostic Interface J533Combi CANDLCData Bus On Board Diagnostic Interface J533J623J217J386J387RJ526J104J431J388J389R78J635J234G85J527J393J401R41Drivetrain CANConvenience CANInfotainment CAN22Data Bus On Board Diagnostic InterfaceMaster FunctionsJ533 is the master for: – Drivetrain CAN continued operation – MOST ring break diagnosis – Data bus system Sleep and Wake-Up operationData Bus System Sleep and Wake-Up OperationJ533 is the master for Sleep and Wake-Up modes. When all the control modules on the Convenience CAN indicate “sleep readiness,” the Gateway sends the sleep command to the CAN-bus and the control modules change to sleep status. The sleep status of the individual control modules and bus systems can be read in the measuring value blocks of J533.Drivetrain CAN Continued OperationOperation of several control modules continues after the ignition is switched OFF. J533 broadcasts a command to end operation to the Drivetrain CAN following an afterrun period.MOST Ring Break DiagnosisJ533 is the diagnosis manager for the MOST bus (discussed later in this book). The interface is responsible for Ring Break Diagnosis and sends the diagnosis data in the MOST bus to J533. Ring Break Diagnosis for the MOST bus is initiated with a Final Control Diagnosis Output Check Diagnosis in J533.Diagnostic WireData Bus On Board Diagnostic Interface J533Data Link Connector (DLC) Break in Optical Fiber23CAN-bus Fault DiagnosisDiagnostic InformationCAN-bus systems are very reliable. Messages such as “Drivetrain data bus defective” may be displayed by VAS scan tools, indicating a need for CAN diagnosis. Further indications of fault causes may be provided by the Gateway measuring value blocks. The starting point for diagnosis is always Guided Fault Finding using the VAS 5051. Malfunctioning control modules can cause results similar to those caused by data bus faults, but fault messages stored in the Gateway can be used as a benchmark for diagnosis. Continuity checks of the Drivetrain CAN can be carried out using an ohmmeter. For the Convenience/ Infotainment CAN, the VAS 5051 DSO function is always required. On later model Audi vehicles, it is possible to access the Gateway directly through Address Word 19 using VAS scan tools. On earlier vehicles, access to the Gateway is through the instrument cluster or vehicle electrical system control module, using Address Word 17.Note Assignment of measuring value blocks may deviate from the example shown! Always check Guided Fault Finding for current vehicle information.Drivetrain CANEngine control unit Steering angle sensor Central electrics *) Battery management --Gearbox control unit Airbag control unit Four-wheel drive electronics *) Electronic ignition lock --ABS control unit Electric steering *) Distance regulation electronics Self-levelling system ----Diesel pump control unit *) --Damper control ---Convenience CANSingle wire/ dual wire Rear left door electronics Dash panel insert *) Roof electronics Auxiliary heater *) Tow hitch control unit *) Central convenience electronics Rear right door electronics Multi-function steering wheel Front pass. memory seat electr. Electronic ignition lock Driver door control unit Driver memory seat electronics Climatronic Rear memory seat electronics Wiper electronics Front passenger control unit Central electronics Tyre pressure monitoring Park distance regulation -----Centr. operator display unit, front Centr. operator display unit, rearInfotainment CANSingle wire/ dual wire Voice activation *) Operator display unit, front Digital sound system *) Special equipment/ vehicle type Radio CD changer *) Operator display unit, rear Multi-function steering wheel *) Navigation Gateway *) --Auxiliary heater Telephone Telematics *) Dash panel insert *) ---24CAN-bus Fault DiagnosisNewer Audi models will have all Drivetrain and Convenience/Infotainment CAN control modules linked to a matching connector in a star pattern. These connectors are located on the left and right sides of the instrument panel.The left and right connectors are also linked by CAN-bus wires so that, in the end, all Convenience/Infotainment CAN and Drivetrain CAN control modules are connected.25CAN-bus Fault DiagnosisTest BoxTest Box 1598/38 can be used with the CAN connectors. This test box can access the individual Drivetrain and Convenience/Infotainment CAN control module wires with the VAS 5051 scan tool DSO. Individual control modules can also be disconnected from the bus system, when trying to isolate CAN-bus short circuits, for example. The link connecting the CAN wires of the individual control modules is connected at the test box.Convenience CAN WireDrivetrain CAN WireDriver-Side Connector Front Passenger Side CAN ConnectorCAN Wires to Control ModulesCAN Wires to Control Modules26CAN-bus Fault DiagnosisT46a J527 J386 J388 J446 J345 J502 J136 J518 J524 J519 J527 J104 J234 J431J533 J387 J389 J520 J393 J644 J364 J528 J521 J522 J589 J255J533 J540 J217 J623 J197T46bBlock Diagram ExampleKeyJ104 J136 J197 J217 J234 J255 J345 J364 J386 J387 J388 J389 J393 J431 J446 J502 J518 J519 J520 ABS Control Module Memory Seat/Steering Column Adjustment Control Module Level Control System Control Module Transmission Control Module (TCM) Airbag Control Module Climatronic Control Module Towing Recognition Control Module Auxiliary Heater Control Module Driver’s Door Control Module Front Passenger’s Door Control Module Left Rear Door Control Module Right Rear Door Control Module Comfort System Central Control Module Headlamp Range Control Module Parking Aid Control Module Tire Pressure Monitoring Control Module Access/Start Control Module Vehicle Electrical System Control Module Vehicle Electrical System Control Module 2 = Drivetrain CAN-High = Drivetrain CAN-Low = Convenience CAN-Low J623 J644 T46a T46b J528 J533 J540 J521 J522 J524 J527 Passenger Memory Seat Control Module Rear Memory Seat Control Module Rear Information Display Control Head Steering Column Electronic Systems Control Module Roof Electronics Control Module Data Bus On Board Diagnostic Interface Electro-Mechanical Parking Brake Control Module Engine Control Module (ECM) Energy Management Control Module 46-Pin, Black Connector at Left CAN Breaker 46-Pin, Black Connector at Right CAN BreakerColor Code= Convenience CAN-High27CAN-bus Fault DiagnosisDSO Representation of CAN SignalsData Transfer on the Drivetrain CANThrough the VAS 5051, the Drivetrain CAN is displayed at the highest resolution (0.02 ms/Div and 0.5V/Div) and the image is then saved (freeze frame). Due to problems with resolution, the measurement should not be carried out in atypical peak areas (at the extreme ends of the image, for example).Representation of Drivetrain CAN on the VAS 5051 DSOFreeze FrameTest Cursor Channel AAmplitude Channel AAmplitude Channel BTime ValueCursor 1Trigger PointTest Cursor Channel BThe test cursor should be positioned in the middle of one of the flat impulses to achieve a reliable test value. The displayed measurement shows a Drivetrain CAN that has just reached the specified value.It should be noted that the measured signal values are determined by the individual control modules. As a result, completely different voltages can be measured during measurements that follow in succession. If the signals from other control modules are displayed, differences of 0.5V are not uncommon.28CAN-bus Fault DiagnosisData Transfer on the Convenience/Infotainment CANUnlike representation of CAN data on the Drivetrain CAN, different zero points on the CAN-bus are selected below. The CAN-high wire is shown in yellow and the CAN-low wire is shown in green. Triggering occurs here at a CANhigh level of approximately 2V. It should be noted that the measured signal values are also determined by individual control modules on the Convenience/Infotainment CAN. Subsequent measurements could result in completely different voltages.Representation of Convenience/Infotainment CAN on the VAS 5051 DSOTrigger PointWarning! Unlike the Drivetrain CAN, the Convenience/Infotainment CAN always has voltage when the vehicle battery is connected. Checking for an open circuit or short circuit can be done using an ohmmeter only when the vehicle battery has been disconnected.29CAN-bus Fault DiagnosisDSO Displays for the Drivetrain CANWhen you encounter a stored DTC, such as “Drivetrain data bus defect,” it is sometimes necessary to investigate the problem with the DSO. It is then possible to determine where the problem is located, and whether it stems from a physical problem such as a short circuit in the wiring. Note In each of the following DSO displays, Channel A was used to display voltage on the CAN-high wire while Channel B was used to monitor voltage levels on the CANlow wire!Conditions That Can Be Analyzed Using DSO Displays:1 Short circuit between CAN-high and CAN-low 2 Short circuit between CAN-high and positive voltage 3 Short circuit between CAN-high and Ground 4 Short circuit between CAN-low and Ground 5 Short circuit between CAN-low and positive voltage 6 Open circuit in CAN-high data path 7 Open circuit in CAN-low data path30CAN-bus Fault DiagnosisShort Circuit Between CAN-High and CAN-LowThis short circuit pulls voltages down to the recessive level (approximately 2.5 volts). The electronic control modules on the Drivetrain CAN can be disconnected and then reconnected to determine whether the short circuit is emanating from an ECM or whether it is being caused by physical contact between the CAN-high and CAN-low wires. If the short circuit is in the wiring, then each set of CAN wires (CAN-high and CAN-low) must be separated from the wiring connector, one after the other, while observing the DSO display. The DSO display will return to normal when the defective set of wires is disconnected.Note Do not separate CAN wires from the wiring connector unless this is the only available option for making required measurements.Short Circuit Between CAN-High and Battery Positive (+) VoltageThis short circuit raises the voltage level in the CANhigh wire to approximately 12 volts, while the recessive voltage in the CAN-low line also rises to approximately 12 volts. The reason for this response pattern is rooted in the internal circuit layout connecting CAN-high and CAN-low within the ECM’s transceiver circuit. The source of the malfunction can be localized using the same technique described above for a short circuit between CAN-high and CAN-low.31CAN-bus Fault DiagnosisShort Circuit Between CAN-High and GroundThis short circuit pulls the voltage in the CAN-high wire down to 0 volts, while the voltage level in the CAN-low wire also drops to 0 volts, although minute voltage fluctuations may still be visible in the CAN-low wire. The source of the malfunction can be localized using the same technique described for a short circuit between CAN-high and CAN-low.Short Circuit Between CAN-Low and GroundThis short circuit means that voltage levels in the CANlow wire are approximately 0 volts. The recessive voltage level in the CAN-high line is also pulled to 0 volts. The source of the malfunction can be localized using the same technique described for a short circuit between CAN-high and CAN-low.Note In each of these DSO displays, Channel A was used to display voltage on the CANhigh wire while Channel B was used to monitor voltage levels on the CAN-low wire!32CAN-bus Fault DiagnosisShort Circuit Between CAN-Low and Battery Positive (+) VoltageThis short circuit means that both voltage levels are pulled to approximately 12 volts. This defect will also generate power readings of approximately 12 volts throughout the Drivetrain CAN. The source of the malfunction can be localized using the same technique described for a short circuit between CAN-high and CANlow.Open Circuit in CAN-High Signal Path33CAN-bus Fault DiagnosisOpen Circuit in CAN-Low Signal Path34CAN-bus Fault DiagnosisDSO Displays for the Convenience/Infotainment CANIn responding to stored DTCs, indicating problems such as “Convenience data bus defect,” it will be necessary to use the DSO to isolate the problem, identify where the defect is located, and determine whether it stems from a physical problem such as a short circuit between two wires. Also significant is that the Convenience/Infotainment CAN support single-wire operation. This means that when responding to a stored DTC such as “Convenience data bus in single-wire operation” it will be necessary to use the DSO to determine which of the two CAN-bus wires is the source of the problem.Note In each of the following DSO displays, Channel A was used to display voltage on the CAN-high wire while Channel B was used to monitor voltage levels on the CANlow wire!Short Circuit Between CAN-High and CAN-LowThis short circuit means that voltage levels on the CAN-high and CAN-low wires are the same, A short circuit between a CAN-high and a CAN-low wire will affect the entire Convenience/Infotainment CAN. The Convenience/Infotainment CAN responds to this error by reverting to single-wire operation. This means that all data communications must be expedited by modulating voltage levels in just a single wire (refer to section on test data blocks). The control module then interprets this voltage by using ground as its baseline reference. In the first DSO display (top), the zero-level axes for Channel A and Channel B are superimposed. This display makes it easy to see that the voltage levels being transmitted through the CAN-low and CAN-high lines are identical. The second DSO display (bottom) shows the same signal with the zero-level axes at mutual offset.35CAN-bus Fault DiagnosisShort Circuit Between CAN-High and GroundThis short circuit pulls the voltage on the CAN-high wire to 0 volts, while voltage levels on the CAN-low wire remain normal. This defect causes the entire Convenience/Infotainment CAN to revert to single-wire operation. At first glance, one might also conclude that the problem could be an open CAN-high wire, but the actual DSO display for an open wire has a different appearance.Short Circuit Between CAN-High and Battery Positive (+) VoltageThis short circuit means that voltage on the CAN-high wire has risen to approximately 12 volts, or battery voltage. Voltage levels on the CAN-low wire remain normal. This defect causes the entire Convenience/ Infotainment CAN to revert to single-wire operation.36CAN-bus Fault DiagnosisShort Circuit Between CAN-Low and GroundThe short circuit causes the voltage on the CAN-low wire to fall to 0, while voltage levels on the CAN-high wire remain normal. This defect causes the entire Convenience/Infotainment CAN to revert to single-wire operation. At first glance, one might also conclude that the problem could be an open CAN-low wire, but the actual DSO display for an open wire has a different appearance.Short Circuit Between CAN-Low and Battery Positive (+) VoltageThis short circuit means that voltage on the CAN-low wire has risen to approximately 12 volts, or battery voltage. Voltage levels on the CAN-high wire remain normal. This defect causes the entire Convenience CAN or Infotainment CAN to revert to single-wire operation.37CAN-bus Fault DiagnosisOpen Circuit on CAN-Low Signal PathVoltage levels on the CAN-high wire are normal. A recessive voltage of 5 volts can be observed on the CANlow wire along with a dominant 1 volt for a duration of one bit. This dominant signal voltage is transmitted by electronic control modules when they correctly receive an intact message. This means that the DSO display pattern shown is actually composed of transmissions from several control modules. Thus, component “A” is part of a message currently being transmitted by a control module. The receiving control modules confirm correct reception of an intact message with a dominant voltage in time slot “B” (Acknowledge signal). At “B” all of the control modules that have received the message intact simultaneously transmit a dominant voltage. This explains the somewhat greater voltage differential on this bit.This second DSO illustration shows the same defect using a lower time sweep. Here we see that the message “1” is only transmitted on the CAN-high wire, although the acknowledgement signal is also sent on the CANlow wire at point “A.” The same applies for the message “2” and the aknowledgement signal “B.” Message “3” is transmitted on both wires. At “3” the corresponding voltage appears on the CAN-low wire. Messages “A,” “B,” and “D” are transmitted in single-wire operation, while the message “C” is sent in the two-wire mode.38CAN-bus Fault DiagnosisOwing to the open circuit, when control module 1 transmits a message, the other control modules will be able to receive it in single-wire operation only (“1,” “2” and “4” in the top DSO display). Through the link to the test connection on control module 4, the DSO portrays the single-wire transmission from control module 1. If control modules 2, 3, 4, 5 and 6 now acknowledge reception, the DSO will show this on both channels (“A,” “B” and “D” in the top DSO display), as there is no open circuit between these control modules. If, for example, control module 2 transmits a message, all other control modules with the exception of control module 1 will receive it in two-wire mode (“3” and “C” in the top DSO display). Meanwhile, control module 1 receives the message in single-wire operation.Open Circuit in CAN-High Wire39CAN-bus Fault DiagnosisDSO Displays for Short Circuits with Contact ResistanceThe short circuits portrayed up to this point have been direct shorts without contact resistance. In the real world, however, short circuits are often caused by abraded insulation on the wiring. If this kind of wire then comes into gentle contact with Ground or positive voltage, which frequently happens in the presence of moisture, there will be “contact” or “transition” resistance at this point. The following DSO displays show this kind of short circuit with its contact resistance.Short Circuit from CAN-High to Battery Positive (+) Voltage with Contact ResistanceCAN-high shorting to positive with contact resistance shifts the recessive voltage in the CAN-high signal path toward positive voltage. As we see from the DSO display, the recessive voltage in the CAN-high line has increased from its normal level of roughly 0 volts to approximately 1.8 volts. This figure of 1.8 volts will vary according to the resistance at the short. Lower levels of resistance correspond to higher recessive voltage levels. This trend culminates in voltage equal to battery voltage when there is no transition resistance at the point of the short circuit.40CAN-bus Fault DiagnosisShort Circuit from CAN-High to Ground with Contact ResistanceThis short circuit from CAN-high to Ground with contact resistance shifts the dominant voltage in the CAN-high signal path toward Ground. The DSO display shows how the dominant CAN-high voltage has shifted from its usual level of roughly 4 volts to approximately 1 volt. The 1-volt figure will actually vary according to the level of contact resistance at the short. Lower levels of resistance will lead to lower dominant voltage levels. This trend culminates at a level of 0 volts in cases where there is no transition resistance.Short Circuit from CAN-Low to Battery Positive (+) Voltage with Contact ResistanceThis short circuit from CAN-low to positive with contact resistance shifts the recessive voltage in the CAN-low signal path toward positive. AS the DSO display shows, the normal CAN-low recessive voltage of roughly 5 volts has risen to approximately 13 volts. The 13-volt figure is determined by the level of transition resistance, and can vary. Smaller resistance levels produce proportionately higher recessive voltages. If there is no transition resistance at the short, the voltage level will coincide with battery voltage.41CAN-bus Fault DiagnosisShort Circuit from CAN-Low to Ground with Contact ResistanceWith a short circuit from CAN-low to Ground with contact resistance, the recessive voltage on the CAN-low signal path shifts toward 0 volts. The DSO display shows how the normal CAN-low recessive voltage of roughly 5 volts has dropped to approximately 3 volts. This 3-volt figure varies according to the actual level of transition resistance. Lower resistance levels will be accompanied by lower recessive voltage levels. If there is no transition resistance at the short, the voltage level will be 0 volts.Short Circuit from CAN-High to CAN-Low with Contact ResistanceThis short circuit from CAN-high to CAN-low with contact resistance reduces the difference in the recessive voltage levels in the CAN-high and CAN-low lines. Instead of its normal 0 volts, the recessive voltage in the CAN-high signal path is now approximately 1 volt. Meanwhile, the recessive CAN-low voltage is approximately 4 volts instead of the usual 5 volts. The dominant voltages in the CAN-high and CAN-low signal paths are normal.42CAN-bus Fault Diagnosis Notes43Other Data Bus TechnologyOverviewMore control modules, divided functions and data exchane have spurred constant development of vehicle data transmission technology. The following data exchange innovations have been added to familiar Audi CAN-bus systems: – Single-wire data bus — Local Interconnect Network (LIN) – Fiber-optic data bus — Media-Oriented Systems Transport (MOST) – Wireless data bus — Bluetooth wireless data transmission technologyInstrument Cluster Control Module J285Distance Regulation Control Module J428 Data Link Connector (DLC)Distance RegulationDiagnosisABS Control Module J104 DrivetrainParking Aid Control Module J446Engine Control Module (ECM) J623Transmission Control Module (TCM) J217ConvenienceRoof Electronics Control Module J528 Data BusClimatronic Control Module J255Heated Windshield Control Module J505Data BusRear Sliding Sunroof Motor V146Fresh Air Blower Control Module J12644Other Data Bus TechnologyKeyDrivetrain CAN Instrument Panel/Gateway Interface CAN Distance Regulation CAN Diagnosis CAN Convenience CAN Local Interconnect Network (LIN) Data Bus Fiber-Optic Data Bus (MOST)Instrument Cluster/ Gateway Interface CANWireless Data Bus (Bluetooth) Telephone/Telematics Control Module J526Cellular Telephone R54Front Information Display Control Head Control Module J523TV Tuner R78Fiber-Optic Data Bus (MOST)Data Bus On Board Diagnostic Interface J533 (Gateway)Map ReaderNavigation System with CD Drive Control Module J401Digital Sound System Control Module J52545LIN Data BusIntroductionAll Local Interconnect Network (LIN) data bus control modules in an individual network are located within a limited vehicle area, such as the roof. This kind of network is also sometimes called a local sub-system. The data exchange between the individual LIN systems in a vehicle is always controlled by a control module through the CAN-bus. Each LIN data bus system functions as a single wire bus. The base color of the wire insulation is violet with an identifying stripe in an additional color. The wire gage is 0.35 mm. Shielding is not necessary. Each LIN data bus system allows data exchange between a LIN master control module and up to 16 LIN slave control modules.LOCAL INTERCONNECT NETWORKClimate ControlLIN Slave Control Module 1 (Heated Windshield Control Module J505) LIN Slave Control Module 3 (Right Rear Footwell Heater Z43)LIN Master Control Module 1 (Climatronic Control Module J255)LIN Slave Control Module 2 (Fresh Air Blower Control Module J126) Infotainment CAN LIN Slave Control Module 4 (Left Rear Footwell Heater Z42)LIN Master Control Module 2 (Roof Electronics Control Module J528)Roof ModuleLIN Slave Control Module 1 (Rear Sliding Sunroof Motor V146)46LIN Data BusLIN Master Control ModulesThe control module in the LIN system that is connected to a CAN-bus performs the LIN master control module function. The LIN master control module controls the data transfer and the data transfer speed. It also sends the message header. The software contains a cycle to control when and how often a message is sent on the LIN data bus. The LIN master control module assumes the translation function between the LIN slave control modules of the local LIN data bus system and the associated CAN bus. The LIN master control module is the only control module in a LIN data bus system that is also connected to a CANbus. The connected LIN slave control modules are diagnosed through the LIN master control module.Note For more information on message headers, refer to page 51.Example of LIN InterfacesData Bus On Board Diagnostic Interface J533 (Gateway) LIN Master Control Module (Climatronic Control Module J255)LIN Slave Control Module 1 (Heated Windshield Control Module J505)Data Bus16-Pin Data Link Connector (DLC)47LIN Data BusLIN Slave Control ModulesLIN slave control modules can be either individual control modules like the Control Module for Fresh Air Blower J126, or sensors and actuators like a Vehicle Inclination Sensor G384 or a Signal Horn for Alarm System H18. Electronics that evaluate the measured values are integrated into the sensors. Communication of these values is then accomplished on the LIN data bus in the form of a digital signal. Only one pin is needed for several sensors and actuators at the socket of the LIN master control module. The LIN actuators are intelligent electro-mechanical subsystems that receive their commands in the form of LIN data signals from the LIN master control module. The actual condition of the actuators can be monitored by the LIN master control module. This allows comparison between actual and specified values.Note Sensors and actuators only respond when a header is sent by the LIN master control module.LIN Slave Control ModulesSensorsLIN Master Control Modulet°MActuators48LIN Data BusDiagnostic InformationThe data transmission rate can be from 1 to 20 kilobits per second (kbits/s). A specific rate is programmed into the software of each LIN control module. This is at most approximately one-fifth of the data transmission rate of the Convenience/Infotainment CAN.1 to 20 kbits/sRecessive LevelSignalRecessive LevelIf no message or a recessive bit is sent on the LIN data bus, the voltage of the data bus wire is close to battery voltage.2V/Div.=0,5ms/Div.Dominant LevelTo transmit a dominant bit on the LIN data bus, the data bus wire is switched to ground by a transceiver in the transmitter control module.TDominant LevelNote Because of different designs of transceivers in the control modules, differences in the dominant levels may be visible on the display.49LIN Data BusTransmission ReliabilityBy specifying tolerances for transmitting and receiving within the range of recessive and dominant levels, a stable data transfer is assured. To be able to receive valid signals in spite of interference radiation, the specified voltage ranges are higher on the receiving side.Voltage Range for Receiving Vbattery VbatteryVoltage Range for ReceivingVrecessiveminimum80%Vrecessiveminimum60%Vdominantmaximum40%Vdominantmaximum20%Terminal 31Terminal 3150LIN Data BusMessagesMessage with Slave AnswerIn the message header, the LIN master control module requests information such as switch conditions or measuring values from a LIN slave control module. The LIN slave control module sends the information back to the LIN master control module in response.Message with Master InstructionsUsing an identifier in the message header, the LIN master control module can also request that the LIN slave control module process the data contained in its response. The LIN master control module processes the data and sends the response.Message Header Transmitter: LIN Master Control ModuleMessage Contents Transmitter: LIN Master or LIN Slave Control Module2V/Div.=0,5ms/Div.T51LIN Data BusMessage HeaderThe LIN master control module transmits the header in cycles. The header can be subdivided into four sections: – Synchronization break – Synchronization delimiter – Synchronization field – Identifier field The synchronization break (synch break) is at least 13 bits long. It is sent with the dominant level. The length of 13 bits is necessary to clearly inform the LIN slave control modules about the start of a message. In the succeeding messages, a maximum of 9 dominant bits are transmitted one after the other. The synchronization delimiter (synch delimiter) is at least 1 bit long and recessive (~Vbattery). The synchronization field (synch field) consists of the bit rate 0 1 0 1 0 1 0 1 0 1. Because of this bit rate, all LIN slave control modules can adapt to or synchronize with the system cycle of the LIN master control module. The synchronization of all control modules is necessary for an error-free data exchange. Loosing the synchronization would cause the insertion of the bit values into the message at the receiving end. This would lead to errors in the data transfer. The identifier field is 8 bits long. The first 6 bits contain the message identification and the number of data fields of the response. The number of data fields in the response may be between 0 and 8. The last 2 bits contain the check-total of the first 6 bits for the identification of transmission errors. The check total is necessary to avoid the assignment of the identifier to a wrong message in case of a transmission error.Synchronization DelimiterSynchronization BreakSynchronization FieldIdentifier Field2V/Div. =0,2ms/Div.T52LIN Data BusMessage Contents (Response)The LIN slave control module adds information to a message with slave response based on identifiers.Example: LIN Master Control Module (Climatronic Control Module J255) LIN Slave Control Module 1 (Heated Windshield Control Module J505)Inquiry About Fan Speed Speed = 150 RPM LIN Slave Control Module 2 (Fresh Air Blower Control Module J126) Reports Actual Fan SpeedFor a data request message from the master, the master control module adds the response. Depending on the identifier, the applicable LIN slave control modules use the data to perform functions.Example: LIN Slave Control Module 1 (Heated Windshield Control Module J505)LIN Master Control Module (Climatronic Control Module J255)Set Fan Speed LIN Slave Control Module 2 (Fresh Air Blower Control Module J126) Reports Actual Fan SpeedSpeed = 200 RPM53LIN Data BusThe response consists of one to eight data fields. One data field consists of 10 bits. Each data field consists of one dominant start bit, adata byte that contains the information, and one stop bit. The start and stop bits are used for the after-synchronization to avoid transmission errors.2V/Div. =0,5ms/Div.Sequence of MessagesThe LIN master control module sends the headers as well as the responses to master messages on the LIN data bus according to a specified sequence and cycle. Information that is used frequently is sent frequently. The sequence of the messages can change depending on the prevailing conditions of the LIN master control module. Example of prevailing conditions: – Ignition ON or OFF – Diagnostics active or inactive – Parking lights ON or OFF To reduce the variety of LIN master control modules, the LIN master control module sends the headers through the LIN data bus addressed to all of the applicable control modules for a fully equipped vehicle. Since there may be control modules addressed that are not installed on a specific vehicle, headers for these messages will be shown on the oscilloscope without responses. This does not affect the functioning of the system.RecessiveTResponseMaster Message2V/Div.=2ms/Div.DominantTHeader Without ResponseSlave Message Indicated by Different Dominant Levels54LIN Data BusTheft ProtectionData transmission on the LIN data bus only occurs when a LIN master control module sends a header with the applicable identifier. Manipulation through a LIN wire from outside the vehicle is impossible because of the complete control of all messages by the LIN master control modules. LIN slave control modules can only answer. For example, doors cannot be opened by tapping into the LIN data bus because of this limitation. With this arrangement, LIN slave control modules can also be installed on the outside of the vehicle. The Garage Door Opener Control Module J530 can be located in the front bumper for example, without compromising the security of the vehicle or the garage.Left Heated Door Lock Control Module J210Laptop ComputerAttempted ManipulationVehicle Electrical System Control Module 2 J520Garage Door Opener Control Module J530 Data From Laptop Computer Not Understood Driver’s Door Control Module J38655LIN Data BusDiagnosisDiagnosis of the LIN data bus system is done through the Address Word for the relevant LIN master control module. The transfer of diagnostic data from the LIN slave control modules to the LIN master control module occurs on the LIN data bus. All of the On Board Diagnostic (OBD) functions are available for LIN control modules.Example of Diagnosis Capabilities Fault Location LIN Slave Control Module Example: Fan Control Fault Text No signal / no communication Cause of Diagnostic Trouble Code (DTC) Failure of data transmission from the LIN slave control module within a specified time interval that is programmed into the software for the LIN master control module. • Break in wiring or short circuit. • Faulty voltage supply for the LIN slave control module. • Wrong part for LIN slave control module or LIN master control module. • Faulty LIN slave control module. LIN Slave Control Module Example: Fan Control Implausible signal Fault in the check total. Incomplete transmission of the messages. • Electro-magnetic interference affecting the LIN wire. • Capacity and resistance changes of the LIN wire (such as moisture or contamination at the connector). • Software problem (wrong version).56Fiber-Optic Data BusIntroductionIn addition to a CAN-bus system, a fiber-optic data bus system was installed for the first time in the 2004 Audi A8L. Media Oriented Systems Transport (MOST) fiber-optic data bus technology was developed by a group of automobile manufacturers, their suppliers, and software manufacturers. MOST is a unified data bus system that makes rapid data transmission possible. The MOST standards developed by this cooperative effort have resulted in a network specifically designed to relay media-oriented data. Contrary to what happens on a CAN-bus, the fiber-optic data bus based on the MOST protocol allows address-oriented messages to be sent to a specific recipient. This technology is used in Audi vehicles for infotainment system data transmission. The infotainment system offers a variety of modern information and entertainment media.DVD VideoDAB Digital RadioCell Phone TelematicsCentral Display and OperationTV ReceptionCD / DVD NavigationInternet E-mail Minidisc / CD Audio57Fiber-Optic Data BusTransmission Rates of