Haldex Controller

VE Haldex Controller and Gen4 plug-and-play harness beside a phone showing the app Torque Map editor

PLUG & PLAY ยท STANDALONE AWD CONTROL

VE Haldex Controller

Your Haldex. Your control. Shape how your all-wheel-drive system responds. Choose your mode, build your own maps and adjust Haldex engagement in real time with the app.

Upgrade a compatible factory Haldex car with a plug-and-play kit, or take control of the Haldex system in a custom AWD conversion.

Available since 2016. Proven through years of use, with continued support from vd Veer Engineering.

VAG Gen1 ยท Gen2 ยท Gen4 ยท Gen5

Volvo P2 ยท Saab XWD

Android & iOS

Plug & play / Standalone

Tune it your way

Modes and custom map editors

Adjust in real time

App control and live monitoring

Connect your build

CAN bus and wired inputs

Choose your installation

Factory car or AWD conversion

TAKE CHARGE OF YOUR AWD

Decide when and how your Haldex engages

The VE Haldex Controller gives you adjustable control over the Haldex coupling. Use a fixed engagement setting or let a custom map respond to inputs such as throttle, vehicle speed and boost.

Build a setup around the way you use your car, from everyday driving to a dedicated track or drag build.

Vehicle / ECU
CAN bus or wired signals

โ†’

VE Haldex Controller
Your modes and maps

โ†“

Haldex coupling
Engagement control

Configure and monitor through the app. Input requirements depend on the selected mode.

01 / ROAD

Everyday driving

Set up a response that suits your car and switch modes when your requirements change.

02 / TRACK

Track setups

Explore throttle, speed and steering-based control with configurable Track mode settings.

03 / DRAG

Drag builds

Tailor engagement for your setup and use Off mode to disengage the Haldex when required.

04 / CUSTOM

AWD conversions

Run a compatible Haldex system in a conversion using a standalone harness and suitable input signals.

SUPPORTED VEHICLE BRANDS

Haldex control across
the brands you know

Controller options for selected Haldex-equipped models, with plug-and-play kits for supported factory installations and standalone options for custom builds.

Volkswagen

Audi

SEAT

ล koda

Volvo

Saab

Ford

Match your specific vehicle, Haldex generation and wiring harness. Brand alone does not determine compatibility.

Check your application โ†’

TWO WAYS TO INSTALL

Factory Haldex car?
Custom AWD build? Both covered.

Choose the controller variant and harness for your Haldex unit and vehicle.

Gen4 plug-and-play kit with preassembled inline wiring harness

Factory AWD vehicles

Plug & play

An inline harness connects the controller to a supported original Haldex installation, keeping the factory wiring intact.

โœ“   No cutting or splicing with the correct kit.

โœ“   Retains the existing Haldex hardware.

โœ“   Removable for transfer to a compatible installation.

Standalone VE Haldex Controller kit with Haldex connector and separate input wiring

Swaps & custom builds

Standalone

Control a compatible Haldex system outside its original vehicle. Use CAN data, wired inputs or a combination to suit the signals available in your build.

โœ“   Standalone harness for a custom installation.

โœ“   Analog throttle and boost, plus wired speed and brake inputs.

โœ“   No original donor ABS module required for standalone operation.

Standalone describes the controller installation. Your build still needs the compatible Haldex hardware, correct wiring and the signals required by your chosen modes.

THE HALDEX CONTROLLER APP

Live dashboard.
Quick, direct control.

Connect your phone, choose a mode and see what your Haldex is doing. Adjust your setup in real time through the app for Android and iOS.

Your main controls in one place

Quick-mode buttons, the selected lock value and access to the active map keep everyday adjustments close to hand.

Watch the signals behind the response

View available RPM, speed, throttle, boost, brake pressure and temperature data alongside Haldex status.

Set it up around your car

Choose a startup mode, select input sources, calibrate signals and configure the optional manual switch.

Download the VE AWD Controller app

Free on Android and iOS. Pair over Bluetooth with your VE Haldex Controller. No VE account or subscription required.

App screens show example configurations and values. Available data and functions depend on the Haldex generation, firmware and connected inputs.

Haldex Controller app: Live dashboard. Quick modes, Haldex status and vehicle data in one view.

Your Haldex at a glance

Quick modes and live vehicle data, with the active Haldex setting on the dashboard.

CONTROL MODES EXPLAINED

Choose how your
Haldex responds

Hold a fixed lock setting, follow an input-based map or build a more detailed response for your track setup.

Fixed or input-based

Lock holds your chosen engagement setting. Throttle, Speed and Boost follow their own configurable input maps.

Combine signals

Map mode uses throttle and speed. Track mode brings throttle, steering and separate speed ranges together.

Off or original vehicle control

Off disables the Haldex. Stock / Passthru lets a compatible factory installation use original vehicle control.

โ–ธ Lock mode

Choose a fixed Haldex engagement setting. Keep the selected level rather than using an input-based map.

โ–ธ Throttle mode

Build your own throttle map. Set how much Haldex engagement to request at different throttle positions.

โ–ธ Speed mode

Map Haldex engagement against vehicle speed. Tailor the response across your chosen speed ranges.

โ–ธ Boost mode

Use boost pressure as the control input. Set engagement values for different pressure ranges in your custom boost map.

โ–ธ Map mode

Combine throttle position and vehicle speed in a custom map. Steering-angle options provide another way to shape the response when that input is available.

โ–ธ Track mode

Configure behavior around throttle, speed and steering angle, with brake settings and lock hold for your track setup. Requires the relevant inputs.

โ–ธ Off mode

Disable the Haldex coupling, including the pre-charge pump. The Haldex-driven axle is disengaged.

โ–ธ Stock / Passthru mode

Let the original vehicle control the Haldex while you monitor available data in the app. Shown as Stock in the supplied app examples. For compatible original vehicle installations.

Select a mode for an explanation. Mode requirements depend on your installation and available inputs.

CUSTOM MAP EDITORS

Build your map.
See exactly what you change.

Tune your own Haldex response on the fly. Edit individual ranges or cells, compare values in a heatmap and inspect the throttle ร— speed surface in 3D.

Haldex Controller app: Speed map & presets. Edit engagement by speed range, switch between three presets and see the active row.

Speed map & presets

Set engagement for each speed range. Three presets let you keep different speed maps, with the active range highlighted live.

Haldex Controller app: Throttle ร— speed heatmap. Compare engagement values across throttle positions and vehicle speeds.

Throttle ร— speed mapping

Combine throttle position and vehicle speed in the Torque Map editor. Table and heatmap views make the values easy to compare.

Haldex Controller app: 3D map view. Inspect the shape of your throttle ร— speed map as a 3D surface.

A different view of the same map

Use the 3D view to inspect how engagement changes across the throttle and speed axes.

01

Start with a profile

Choose General, Sport, Track or a blank Torque Map as your starting point.

02

Edit your response

Adjust the ranges or map cells for the behavior you want.

03

Refine and keep it

Watch the active inputs, adjust in real time and use the available save, backup and restore controls.

ADVANCED TUNING

More control for the way you drive

Go beyond a single map with configurable Track settings, wheel-slip response and brake-based control.

Haldex Controller app: Track mode maps. Separate low- and high-speed maps use throttle and steering angle.

Track: low- and high-speed maps

Build throttle ร— steering-angle maps for low and high speeds, then set the speed at which the controller switches between them.

Haldex Controller app: Wheel-slip override. Set a slip threshold and the engagement value used while the override is active.

Respond to wheel slip

Speed mode can override its normal map when the configured wheel-slip percentage is exceeded, using your selected engagement value.

Haldex Controller app: Torque & brake settings. Zero-throttle override, left-foot-brake and brake-pressure map controls.

Tune throttle & brake behavior

Configure zero-throttle override, left-foot-brake mapping and brake-pressure control for your setup.

Control how engagement reduces

Track lock time delays reductions in engagement while increases remain immediate. A low-speed passthrough option can use OEM control where supported.

Use the right live signals

Wheel-slip control needs suitable wheel-speed data; steering- and brake-pressure-based functions need the corresponding inputs.

Keep each behavior adjustable

Set the override thresholds and engagement values to suit your car, rather than relying on one fixed response for every condition.

FLEXIBLE SIGNAL SOURCES

CAN or wired inputs.
Choose each signal source.

Read data over a supported CAN protocol or connect conventional signals for a standalone installation. Configure the input source to match your setup.

SUPPORTED ECU CAN PROTOCOLS

Connect the ECU in your build

Use a supported ECU CAN stream to provide the input data for your Haldex control maps.

MaxxECU ยท ECU CAN input

KMS ยท Kronenburg Management Systems

Haltech ยท ECU CAN input

ECUMaster ยท EMU Black CAN input

MegaSquirt ยท ECU CAN input

FuelTech ยท ECU CAN input

Select the matching protocol, CAN speed and ECU configuration. Available input signals vary by protocol.

CAN BUS INPUT

Bring vehicle or ECU data into your maps

Use available throttle, speed, RPM, brake and other signals from a supported vehicle network or aftermarket ECU.

Vehicle protocols

VAG PQ

VAG MQB

Volvo P1 / P2 / P3

Saab

Ford

Aftermarket ECU protocols

MaxxECU

Haltech

KMS

ECUMaster EMU Black

Megasquirt

FuelTech

Additional CAN protocols can be added if needed. Contact us about your vehicle or ECU.

ANALOG & DIGITAL INPUTS

Wire the signals directly

Conventional inputs support builds where the original vehicle network is absent or does not provide the required data.

โœ“   Throttle: analog position signal.

โœ“   Boost: analog pressure sensor signal.

โœ“   Vehicle speed: wired VSS signal.

โœ“   Brake & handbrake: dedicated control inputs.

Calibrate analog sensors and configure brake behavior for your installation. Follow the wiring guide for electrical connections.

CAN input protocol support does not establish plug-and-play compatibility. Match the Haldex unit, controller variant, wiring harness and input protocol separately.

INPUT SETUP IN THE APP

Mix the sources your build needs

Choose CAN or a conventional input separately for throttle, speed, brake, boost and parking brake. A car can use CAN throttle and speed while taking its brake signal directly from the wiring.

Select a supported CAN protocol to match the vehicle or ECU. Use input diagnostics to inspect incoming values and signal status.

The protocol selector includes KMS alongside MaxxECU, Haltech, EMU Black, Megasquirt and FuelTech. Protocol and signal availability remain specific to your ECU and controller setup.

Haldex Controller app: Choose each input source. Mix CAN and conventional inputs for throttle, speed, brake, boost and parking brake.

CAN & wired signal selection

Choose the source for each supported input.

Haldex Controller app: More CAN protocol options. The protocol list includes MaxxECU, Haltech, KMS, FuelTech and Ford.

Select a CAN protocol

Match the vehicle or ECU protocol to your installation.

EXTERNAL CONTROL OVER CAN BUS

Make Haldex control part of your wider system

A compatible external CAN device can control the Haldex Controller through the VE Haldex Controller CAN protocol. Integrate it into a custom control setup alongside your app-based configuration.

External CAN device
Configured for VE protocol

โ†’

VE Haldex Controller
External CAN control

โ†’

Haldex system
Engagement control

External command support is separate from reading vehicle or ECU input data. Compatible firmware and protocol configuration are required.

Discuss a CAN integration โ†’

CONTROLLER SETUP & DIAGNOSTICS

Configure the details.
Understand your system.

Program physical controls, tailor low-speed behavior and inspect supported Haldex diagnostics from the app.

Haldex Controller app: Program the manual switch. Assign actions to 12 switch positions and calibrate the optional switch.

12-position manual switch

Assign mode or lock actions to the optional switch positions. Guided and fast calibration help match the switch to the controller.

Haldex Controller app: Parking & reverse settings. Configure parking disengagement conditions, reverse behavior and brake ignore.

Parking, reverse & brake behavior

Set speed and steering-angle conditions for parking disengagement, configure reverse disengagement and choose brake-ignore behavior.

Haldex Controller app: Gen5 Haldex diagnostics. Read module information, supported live measurements and fault codes.

Gen5 information & fault codes

On supported Gen5 units, inspect module software information and live measurements, and read or clear fault codes.

Diagnostic measurements and settings vary by Haldex unit. The diagnostic screen shown is a Gen5 example.

CHOOSE THE CORRECT VERSION

Start with your Haldex generation

VAG Gen1, Gen2, Gen4 and Gen5, Volvo P2 Gen2 and Gen3, and Saab Gen4 options cover factory installations and standalone conversions. Identify the Haldex unit and connectors before choosing your kit.

Volkswagen Group (VAG)

VAG examples โ€” identify your actual Haldex unit; model names alone are not a fitment check.
Haldex typeExample applicationsSelection guidance
Gen1Golf Mk4 4Motion / R32, Audi TT 8N, S3 8LMatch the original Gen1 unit and harness. View Gen1 kits โ†’
Gen2Golf Mk5 R32, early A3 / S3 8P quattroCheck production version; models can span generations. View Gen2 kits โ†’
Gen4Golf Mk6 R, RS3 8P, TT RS 8JMatch the Haldex unit and vehicle-specific kit. View Gen4 kits โ†’
Gen5 ยท 0AYAudi S1 8X, selected Sharan, Tiguan and T6 applicationsChoose the correct 0AY / PQ installation. View Gen5 0AY kits โ†’
Gen5 ยท 0CQGolf Mk7 R / 4Motion, A3 / S3 / RS3 8VChoose the correct 0CQ / MQB installation. View Gen5 0CQ kits โ†’

Volvo P2 ยท Gen2 & Gen3

Volvo P2 AWD examples โ€” check the fitted Haldex unit and connectors; model names alone do not confirm the generation.
Haldex typeExample applicationsSelection guidance
Volvo P2 ยท Gen2S60, V70, XC70 and XC90 AWD ยท pre-facelift applicationsMatch the Volvo P2 Gen2 unit and wiring harness. View Gen2 kits โ†’
Volvo P2 ยท Gen3S60 / S60R, V70, XC70 and XC90 AWD ยท facelift applicationsChoose the Volvo P2 Gen3 controller and matching harness; verify the installed unit. View Gen3 kits โ†’

Saab ยท Gen4 XWD

Saab XWD โ€” select the Saab-specific controller and harness for your Gen4 Haldex installation.
Haldex typeApplicationsSelection guidance
Saab ยท Gen4Saab XWD vehicles fitted with a Gen4 Haldex systemMatch the original Haldex unit and connectors to the Saab-specific kit. View Saab plug & play โ†’

Different platform or a custom conversion?

Send your vehicle details, Haldex part number, ECU and available signals. We can help identify the controller and harness your project needs.

Ask about your setup

BEFORE YOU CHOOSE

A few practical questions

โ–ธ Which kit do I need?

Choose plug & play for a supported original Haldex installation. Choose standalone for a conversion or custom wiring setup. Both require the right controller version for the Haldex unit.

โ–ธ Can I use it without the donor carโ€™s ABS?

Yes, in a suitable standalone installation. Supply the signals required by your chosen modes through supported CAN data or wired inputs.

โ–ธ Do I have to use CAN bus inputs?

No. Wired throttle, speed, boost, brake and handbrake inputs let you build a setup around conventional signals. CAN protocols provide another way to access supported data.

โ–ธ Can I tune it in real time?

Yes. The app lets you switch modes, edit maps and adjust settings in real time. Monitor the available data as you refine the setup.

โ–ธ Does an engagement setting guarantee a torque split?

Engagement settings control the Haldex coupling. The torque delivered at the wheels also depends on the drivetrain and operating conditions; a setting is not a measured axle-torque guarantee.

โ–ธ Can an external CAN device control it?

Yes, through the VE Haldex Controller CAN protocol with compatible firmware and a correctly configured external device. Contact us to discuss the integration.

โ–ธ How do I identify my Haldex generation and find its part number?

Look for the original part number on the Haldex unit or its control module. Compare it with the compatibility examples. If you are unsure, send us the part number, vehicle model and year, plus photos of the label and connectors.

โ–ธ What comes in the kit, and what do I need to supply?

A controller kit includes the VE Haldex Controller and the harness for the installation option you choose. Check the specific product listing for its contents and options. For a standalone build, supply the compatible Haldex hardware, power and the input signals your chosen mode needs.

โ–ธ Does my phone need to stay connected after Iโ€™ve set up the controller?

No. Settings are stored on the controller, which starts in the mode you select under Default mode. Reconnect the app when you want to change settings or monitor live data.

โ–ธ Can I switch back to factory AWD behavior?

Yes, on a compatible factory installation. Choose Stock / Passthru in the app to let the original vehicle control the Haldex. This mode is intended for installations that retain the original vehicle control system.

โ–ธ What happens if the controller loses a required CAN signal?

The controller keeps using the last received value for that input until a new value arrives. You can check incoming signals in the appโ€™s Input Diagnostics.

โ–ธ Does the app support Android?

Yes. Download the free VE AWD Controller app from Google Play and connect to your controller over Bluetooth.

โ–ธ Does the app support iOS?

Yes. Download the free VE AWD Controller app from the Apple App Store and connect to your controller over Bluetooth.

โ–ธ Does the app require an account or subscription?

No. The VE AWD Controller app requires neither a VE account nor a subscription. Itโ€™s free to download for Android from Google Play and for iOS from the Apple App Store. Pair your phone directly with the controller over Bluetooth.

SETUP & SUPPORT

Get to know your controller

Use the existing online guides for the current app and installation information.

Volkswagen Golf R and Audi S3 with subtle AWD drivetrain graphics

BUILD YOUR AWD SETUP

Put your Haldex to work.

Find the controller and harness for your factory Haldex car or standalone project, then tune the response to suit your build.