TECHNICAL DOCUMENTATION

SSP 015 Skoda Octavia – Information on the Engineering

PDFEN88 pages5 MB
SSP 015 Skoda Octavia – Information on the Engineering - PDF cover

This PDF is currently unavailable.

Read document text
Service ŠKODA OCTAVIAInformation on the Engineering15Self Study Programme OCProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�I V T AASP15-1A name with tradition modern automotive engineering. The OCTAVIA moves SKODA car manufacture, so rich in tradition, into the mid-class vehicle range. The automotive engineering makes use of proven Group components.2 ContentsThe OCTAVIA Vehicle Safety Engine/Gearbox Combinations Engines Engine/Gearbox Mounting Gearboxes Running Gear Brake System Body Electrical System Heating & Ventilation System Air Conditioning DimensionsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Page4 6 12 14 36 38 44 52 55 62 76 82 84ServiceReparaturleitfaden OctaviaService ServiceReparaturleitfaden Octavia Reparaturleitfaden OctaviaService ServiceReparaturleitfaden Octavia Reparaturleitfaden OctaviaS e r v i c eXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXYou can find information regarding inspection and maintenance, setting and repair instructions in the Workshop Manuals.11.9611.9611.9611.9611.963 The OCTAVIAAn initial overviewVersions availableLX Engine displacement kW GLX SLX1.6 l 551.9 l 501.6 l 551.6 l 741.9 l 501.6 l 741.8 l 921.9 l 66Note: Optional equipment can only be factory-fitted! Individual retrofitting of options is technically complicated.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The Engineering of the OCTAVIA – – – – – – – – – – – – – – – – – –4All-galvanized safety body with side impact protection Windscreen and rear window flush-bonded to body Recirculating air mode with automatic cutout, pollen filter 5-speed manual gearbox Optional 4-speed automatic gearbox with the more powerful engines Front independent suspension (McPherson strut with wishbone arm) Rear trailing arm torsion beam axle Front disc brakes, rear drum brakes (rear disc brakes with certain engines) 14" or 15" wheels (depending on engine) Passenger and driver airbag Power-assisted steering Driver's seat adjustable for height Safety steering column, adjustable fore and aft and for height Steering wheel lock with slip coupling Central locking, Bosch CAN bus system and radio remote control Electronic immobiliser H4 headlights with integrated fog lights Centre high-mounted brake light SP15-2Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Optional equipment – – – – – – – – – – – Seat belt tensioners ABS or ABS with EDL Radio preinstallation Radio/cassette incl. 4 or 8 speakers Rear window wiper Front/rear power windows Passenger's seat adjustable for height Heated front seats Anti-theft alarm Power operated door mirrors Power operated glass sliding roofTechnical data of vehicle Length Width Height Wheelbase Front track Rear track No. of seats Unladen weight 4511 mm 1731 mm 1429 mm 2512 mm 1516 mm 1492 mm 5 1160 - 1345 kg depending on equipment5 Vehicle SafetyThe body structureThe aim of the design work on the OCTAVIA was to produce a protective body structure.SP15-3The FEM = Finite Element Method (computer model in which the body is broken down into minute geometry elements such as rectangles or triangles) was used to process and calculate the body structure for crash analysis. This made it possible to take full account of the following important aspects as early as the development phase – compliance with all existing safety regulations applicable. – ompliance with likely safety regulations, for example crash against a moving barrier as is proposed from the year 2000 on. A further development goal was to ensure that no major parts such as the bonnet, side members, rear doors suffer damage during low-speed crashes - up to 15 km with overlap. Satisfying these requirements is relevant for the car´s classification in the insurance class. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability The OCTAVIA has successfully achieved a very with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� good classification. One of the design features which contributes to this is a specified front crumple zone at the side members. The occupants are protected, the deformation is absorbed by the front members and the remaining side members do not suffer any damage.Specified deformation of the side member 6SP15-4 SP15-5Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The computer model made it possible to acquire valuable knowledge regarding the body cross sections as early as the development phase. These have been optimised in respect of their safety features and the materials used and form the torsionally-stiff passenger cell. Highlights of the body structure – front side member structure extending as far as the middle of the body – front side members designed on the "crumple principle" (specified buckling point) – cross member in the footwell for conducting the forces incurred in a side impact – side and cross members in the rear area – wide B pillars at the point where they connect with the sills – tubular stiffeners in the side sills (as a protection in a side impact) – recessed rain runnels – large, well-rounded exterior body parts – mooth body line from bonnet over windscreen to roof7 Vehicle SafetyOCTAVIA Safety BodySP15-6Safety legislationSafety cellA rigid passenger (safety) cell ensures that the The OCTAVIA not only surpasses all present safety standards but already satisfies intended car occupants are provided with a survival space which does not deform. legislation which exists only as a recommenpurposes, inintegrated part or in whole, is into not permitted the roof frame and dation or draft. Protected by copyright. Copying for private or commercial Pillars unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability lower sill, special impact with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� members (side protection) in the doors and additional stiffening at the window waist rails of the doors ensure safety even in the event of side collisions.Deformation zones Defined crumple zones at the front and rear which deform gently ensure the lowest possible deceleration without any extreme peak values in the level of stresses to which occupants are subjected when wearing their seat belts. The side members crumple with defined buckling during an impact.Flush-bonded windows Windscreen and rear window are flush-bonded to the body which increases the dynamic stability of the body - an important factor in the event of a rollover.8 The new side protectionSP15-7The measures listed below have been incorporated to offer the occupant side protection in the event of a side impact: – – wide sheet sections below the window line stiffen the doors reinforcing tubes in the middle area of the door are capable of absorbing particularly high forces by virtue of their cross section – – tubular reinforcement in the side sills foam-filled side impact absorbing elements in the doors for the pelvis and rib area which move the occupants away from the hard outer parts.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP15-8 The SKODA OCTAVIA after a "frontal crash" testCrash tests are the practical confirmation of the computer-aided body design. They are the starting point for type approval of the vehicle in conformity with internationally valid safety standards.9 Vehicle SafetyPassive safety featuresSP15-9In addition to the design measures relating to the strength and information characteristics of the body, further influencing factors in respect of passive safety ("All measures which are capable of preventing or minimizing the consequences of accidents") have been implemented in the OCTAVIA. Safety steering column – telescopes in the event of a crash, providing additional large unrestricted area from the cross panel to the universal joint shaft of the steering. adjustable fore and aft and for height No relevant intrusion into the interior in the event of a crash; if the airbag is triggered, the protection which it offers is not impaired. Driver airbag with volume of 65 litres Passenger airbag with volume of 90 litres Control unit on centre tunnel, as on the FELICIA. Activated in the event of a collision at a speed of more than 20.5 km/h. with height adjustment and seat belt tensioner on front seats (with optional airbag) front restraints adjustable for height and angle rear restraints adjustable for height with high level of lateral stiffness with impact-absorbing plate in the backrest of the front seats to protect the driver's and front passenger's backs from possible injury from the rear passenger's knees in the event of an accident. with bulkhead as a protection for the occupants with specified buckling pointSteering wheel–Airbag–Three-point seat belt Head restraints Seats– –Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�–Luggage compartment Subframe10– –The OCTAVIA fully complies with all safety standards relating to such components. Front seat belt tensioners (rotary piston tensioner) Design The seat belt tensioner operates on the rotary piston principle with 3 working chambers. Seat belt tensioner and the inertia reel form a compact component. The installation point is the familiar location for the inertia reel seat belt at the bottom of the B pillar. The seat belt tensioner system is activated by a mechanical sensor, which is integrated in the seat belt tensioner, as a function of the deceleration in the event of a collision. Operating principle – The mechanical sensor mecha nism ignites the primary gas generator with an impact bolt and impact igniter.Piston Primary gas generatorNew !Mechanical triggering sensorInertia reel– The expanding gas in the first working chamber causes the piston to rotate. – Once the overflow/outlet port 1 has been reached, the working pressure which exists from the first chamber ignites the secondary gas generator by means of an impact pin. The piston is rotated further as a result of the new propellant charge.SP15-10 Ignition of primary gas generator Overflow port 1Outlet port– Further pressure Protected ignition occur by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability when the other overflow/outlet with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� ports are reached (tertiary gas generator). – The seat belt is tensioned by up to 120 mm within 13 ms.Tertiary gas generator Overflow port 2 Secondary gas generator SP15-11PistonNote: Do not open seat belt tensioner after it has been activated!11 Engine/Gearbox CombinationsEngine range Engine code letter Displacement Output Engine management Magneti Marelli 1 AV EA 111 AEE 1598 cm3 55 kW/75 PS EA 188 AGP 1896 cm3 50 kW/68 PS Direct injection, SDI, electronically controlled distributor injection pumpSP15-12SP15-13Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP15-14 5-speed manual gearbox 02K 12 EA 113 AEH 1595 cm3 74 kW/100 PS Simos 2EA 113 AGN 1781 cm3 92 kW/125 PS Bosch-Motronic M 3.8.2EA 188 AGR 1896 cm3 66 kW/90 PS Direct injection, TDI, electronically controlled distributor injection pumpProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP15-15SP15-16SP15-17SP15-18 4-speed automatic gearbox 01M 5-speed manual gearbox 02J 13SP15-19 EnginesEngine characteristic curves1.6-ltr. AEE70AEE60The 1.6-ltr. petrol engine produces its maximum output of 55 kW/75 HP at a speed of 4800 rpm. It reaches its maximum torque of 135 Nm at 3200 rpm. A torque of at least 120 Nm is available in the range from 2000 up to 4300 rpm.5040AGP1.9-ltr. AGP The 1.9-ltr. SDI engine has a maximum output of 50 kW/68 HP at a speed of 4000 rpm. It produces its maximum torque of 130 Nm at 1800 rpm.302010SP15-201.6-ltr. AEH The 1.6-ltr. petrol engine achieves an output of 74 kW/ 100 HP at a speed of 5800 rpm. It produces its maximum torque of 145 Nm at 3800 rpm. 1.8-ltr. AGNProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The 1.8-ltr. petrol engine produces its maximum output of 92 kW/125 HP at a speed of 5900 rpm. It achieves its maximum torque of 173 Nm at 3900 rpm. 1.9-ltr. AGR The 1.9-ltr. TDI engine achieves its maximum output of 66 kW/90 HP at a speed of 4000 rpm. It produces its maximum torque of 202 Nm at a speed of 1900 rpm.P = Output M = Torque n = Engine speed 14SP15-21 1.6-ltr. petrol engine AEEThis engine will already be familiar to you from the FELICIA. The intermediate plate between engine and gearbox is not required in the OCTAVIA, the hole pattern in the engine flange and gearbox flange being identical. The engine mounting bracket is matched to the new pendulum mounting. The oil pan is now manufactured from die cast aluminium.SP15-22The engine has a new type of clutch.1.9-ltr. naturally aspirated diesel engine AGPThe 4-cylinder SDI naturally aspirated diesel engine (engine code AGP) is a new development for transverse mounting. The air is inducted conventionally, without any turbo boost. Consequently, the designation naturally aspirated diesel. The direct fuel injection principle is employed, which offers high output levels. With a piston stroke of 95.5 mm, the engine is a long-stroke design, which coupled with a cylinder bore of 75.5 mm, produces a displacement of 1.9 litres. The distributor injection pump with electronic control ensures good fuel economy. The naturally aspirated diesel is identical with the TDI in certain components.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP15-23In combination with the emission control system, it surpasses the exhaust limits for direct-injection diesel engines.15 EnginesThe new petrol engines 1.6-ltr. 2-valve AEH 1.8-ltr. 5-valve AGNDevelopment goal: New, powerful engines for transverse mounting, good fuel economy and low emission levels, maximum possible parts commonality.The two petrol engines have their origin in components of the Group engine range. This engine range EA 113 has been developed from these for the OCTAVIA.Common features of the range: – Rotorless high-voltage distribution, no drive required for distributor. Crankshaft position detected by sensor at the crankshaft (reference marks), camshaft position detected by phase sensor at camshaft (see section Electrical System).– Geometrically identical crankcase, light alloy on 1.6-ltr. engine cast iron on 1.8-ltr. engine. – Cross-flow cylinder head. – Oil pump with chain drive, no separate drive shafts required.– Electronic engine manage– Coolant pump integrated Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted ment. All engine control in crankcase, driven by unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.hou� units have identical toothed belt. sings with two-part connector. – Optimised valve gear (valve stem diameter – Identical ancillary mounts 7 mm, single valve spring) - compact arrangement of which reduces moved ancillaries. masses.16 1.6-ltr. petrol engine AEHThe 1.6-ltr. petrol engine AEH is a new powerful engine with light weight and good fuel economy. Advanced design details have made it possible to achieve a compact design as is required for transverse mounting in the car. A further development goal was to surpass legal emission requirements. The engine features an intake manifold with switchover facility. The intake manifold is a plastic component. The intake manifold switchover influences the torque in the lower rpm range, and in the upper rpm range improves output and engine running.SP15-24– Light alloy cross-flow cylinder head – 2 valves for each cylinder – Light alloy cylinder block with internal breather – Integrated cast iron contact surfaces in the cylinders, not replaceable Special features of the 1.6-ltr. AEH – Coolant pump integrated in housing; no separate housing – Rotorless high-voltage distribution – Coated cylinder head gasket made of metal (see also 5-valve engine)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�– Simos 2 engine management system with hot film air mass meter17 EnginesValve N156The variable intake manifold of the 1.6-ltr. AEHVariable intake tracts in the intake manifold make it possible to achieve ideal induction conditions and to have a favourable impact on torque and power output, both for low as well as high engine speed ranges. Four flaps operating synchronously are controlled in line with the engine map, in other words in accordance with the prevailing engine load and speed conditions, to form long or short intake tracts. The short intake tract affects engine output while the long tract influences engine torque. The flaps are vacuum-operated.Vacuum unitReservoir chamber for vacuumLong intake duct Flaps Short intake duct SP15-25The vacuum is stored in a reservoir chamber. The vacuum reservoir makes it possible to achieve up to 15 switching operations. This is important, for example for uncontrolled operations of the accelerator pedal, in particular if the car is fitted with an automatic gearbox. The intake manifold changeover valve N156 directs the vacuum to the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted vacuum unit line with the actuation the flaps by the engine unless authorised by in ŠKODA AUTO A. S. ŠKODA AUTO A. S.of does not guarantee or accept any liability control unit. The flaps are operated mechawith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� nically.The flaps which are open when the engine is idling, close when the throttle is operated. The long intake tract – torque tract – is formed. This produces optimal engine torque.SP15-26 Flaps closed long intake tract = torque duct The flaps open again at engine speed of more than 42000 rpm. The short intake tract – power tract – is now active and the engine is able to provide full power at high revs.Soft governing of engine speed is activated at 6200 rpm. The flaps are closed agian for this purpose. SP15-27 Flaps open short intake tract = power duct 18 1.8-ltr. 5-valve petrol engine AGNThe 1.8-ltr. petrol engine AGN is a powerful engine with light weight and good fuel economy. Advanced design details have made it possible to achieve a compact design as is required for transverse mounting in the car. A further development goal was to surpass legal emission requirements. The engine features 2 camshafts with a hydraulic, map-controlled camshaft adjusting device for the inlet camshaft. The camshaft adjuster influences the overlap of the inlet/exhaust valves and achieves improved cylinder charge. SP15-28Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�– Multipoint injection (MPI) mixture formation – Light alloy cross-flow cylinder head – 5 valves for each cylinder – Cast iron cylinder block with combined block head-crankcase breather – Bosch Motronic M 3.8.2 engine management system with hot film mass air meterSpecial features of the 1.8-ltr. AGN– Coolant pump integrated in housing; no separate housing – Rotorless high-voltage distribution – Coated cylinder head gasket made of metal – Light alloy oil sump – Resonator between air mass meter and throttle valve for the purpose of eliminating acoustically unpleasant vibrations in certain engine speed ranges19 Engines5-valve designThe output of an engine is dependent not only on the displacement and engine speed, but also in particular on how rapidly the charge cycle can be completed. The power which an engine produces is all the more intensive the more fresh gas is able to flow into the combustion chamber within the identical unit of time. The 5-valve design makes it possible to achieve a high power output with a small displacement engine while adjusting the camshaft of the inlet valves optimises the volumetric efficiency and the torque curve of the engine. The engine has three inlet and two exhaust valves which offer a large flow cross section. The inlet and exhaust valves are each controlled by a camshaft.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Inlet valvesExhaust valvesSP15-29The advantages of the 5-valve design– High power output with small displacement. – Good fuel economy as a result of high engine efficiency. – Compact design and low engine weight. – Pleasant engine acoustics and smooth running as a result of low combustion noise level.– Good torque characteristics and high pulling power.20 Valve gear of the 5-valve engineThe five valves are operated by the two camshafts directly by means of hydraulic bucket tappets. The inlet camshaft controls three valves at each cylinder. The exhaust camshaft controls two valves. The exhaust camshaft is crankshaft-driven by means of a toothed belt. It in turn drives the inlet camshaft by means of a chain. This driving chain is maintained at the correct tension by the adjustable chain tensioner (camshaft adjusting device).Adjustable chain tensionerDriving chain Inlet camshaft Exhaust camshaftSP15-30Tensioning deviceThe toothed belt for the camshaft drive is tensioned automatically by a tensioning device.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�21 EnginesCamshaft adjustment of 5-valve engine The camshaft adjuster makes it possible to achieve improved volumetric efficiency in the engine and to optimise the power output curve (high torque and good elasticity at low rpm). The timing and minimal overlap of the opening of the inlet and exhaust valves are critical elements for influencing the gas cycle operations.SP15-31The adjustable chain tensioner operates hydraulically, pressure being supplied by the engine oil pump. The hydraulic cylinder moves the driving chain in its path on the basis of signals supplied by the engine management system to the camshaft adjuster solenoid valve.The length of the chain at the one side is enlarged between the two driving gears of the camshafts and simultaneously shortened at the other side. The result of this is that the inlet camshaft is rotated vis-à-vis the crankshaft-driven exhaust camshaft and the overlap of exhaust valve and inlet valve is thus reduced.12 Timing is altered in line with engine speed and load. 10 The appropriate parameters Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 8 authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability are programmed in theunless map with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� of the engine control unit. 6The effect of the full loaddependent camshaft adjustment is retarded from 0 up to 1300 rpm advanced up to 3600 rpm retarded from 3600 rpm.4 2 0 -60 UT -120 -60 OT 60 120 UT 60SP15-32 UT= OT= = bottom dead centre top dead centre range of overlap22 Cylinder head of 5-valve engineDespite the compact design of this engine, it is possible to remove and insert the cylinder head bolts with the camshafts in place. To permit this, it was necessary to use cylinder head bolts without large washers. The pre-stress force is now introduced into the cylinder head by using hardened and tempered screw-in sleeves. This has a beneficial effect on the settling properties.Cylinder head boltScrew-in sleeveSP15-33Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Metal cylinder head gasketThe cylinder head gasket is composed of 4 individual metallic layers. This prevents compression of the gasket. The sealing surfaces are treated with a special coating in order to ensure good sealing properties.Note: Pay attention to the installation position when installing the cylinder head gasket. The cylinder head bolts do not require to be re-tightened.23 EnginesFully electronic ignitionThe 1.6-ltr. AEH and 1.8-ltr. AGN engines are equipped with a fully electronic ignition. They no longer have any rotating parts for the high-voltage distribution and no distributor is fitted. Double ignition coils (twin-spark ignition coils) are now used in place of the distributor.Advantages: – – – – no rotating parts, no mechanical wear and tear reduction in noise level reduced number of high-voltage connections and susceptibility to faults no mechanical ignition settingThis type of fully electronic ignition is known as a rotorless high-voltage distribution.4 3 2 1Sensor signalsengine control unit2 double ignition coils with power output stage N122 SP15-34 The distributorless ignition system is composed of two double ignition coils in an ignition module. These are operated alternately each by an ignition output stage. The double ignition coil produces two ignition sparks simultaneously at the ignition timing point. Each of the double ignition coils is assigned to the pair of cylinders whose pistons are positioned simultaneously top dead centre (1 and 4 Protected by copyright. Copying for private or commercial purposes, in part at or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. Š KODA2 AUTO A.3, S. does not guarantee or accept any liability and and respectively).with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�24 Example of the operating principle: One double ignition coil is assigned to the cylinder pair 1/4, the other to the cylinder pair 2/3. The entire ignition cycle takes place over 2 revolutions of the crankshaft, in other words over 720°. In the first part of the cycle, the one ignition spark ignites in the compression stroke of cylinder 1 whereas the other ignites simultaneously as "empty ignition" at the end of the exhaust stroke of cylinder 4.1234SP15-35One revolution of the crankshaft later, cylinder 4 is now in the compression stroke and ignites whereas cylinder 1 ignites empty in the exhaust stroke.This ignition cycle applies in the same manner to cylinders 2/3, although this occurs at a crankshaft angle offset by 180° compared to cylinder 1.1234SP15-36Top dead centre sensorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The rotorless high-voltage distribution system requires an electric signal for detecting the top dead centre of cylinder 1+4. A toothed signal ring is attached to the crankshaft.The position of the crankshaft – and also the rotational speed – is detected by an induction sensor at the crankshaft.SP15-37Camshaft position sensor A signal is required from the camshaft in order to detect the camshaft position. On the 1.6-ltr. engine AEH a Hall sender is attached to the camshaft sprocket for this purpose. On the 1.8-ltr. engine AGH a Hall sender in a special housing at the cylinder head is attached to the inlet camshaft for this purpose.SP15-3825 EnginesIgnition - Simos 2 engine management (1.6-ltr. AEH)System functions The system conducts an angle allocation between crankshaft and camshaft. The crankshaft signal rotor has 120 teeth with two gaps of 2 teeth for synchronization. The camshaft plate has a window 180° large. The element which is analysed is always the falling edge of the tooth after the gap. Self-diagnosis detects varlations from the specified values. Start of injection and ignition are computed in line with the sensor signals.Diagram for detecting crankshaft/camshaft position78° BTDC cylinder 1 TDC cylinder 4 74 58 61 88 118 1 TDC cylinder 1 14 28 58 61 TDC cylinder 4 74GapGapGapCrankshaft disc360° Crankshaft360° CrankshaftProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�windowfalling edge 180° camshaft rising edgeCamshaft discSP15-39Crankshaft disc The 1st falling tooth edge after the synchronizing gap is positioned at 78° CA before ignition TDC of cylinder 1 and cylinder 4, respectivelyCamshaft disc The rising edge of the camshaft signal is positioned at the 28th tooth after the window = 14 teeth after ignition TDC of cylinder 1. The falling edge is located at the 88th tooth after ignition TDC of cylinder 1.26 Voltageless lambda probe with defined earth offsetAll the petrol engines in the OCTAVIA feature a voltageless lambda probe. Voltageless means: The lambda probe is no longer supplied with its earth for the signal voltage through the female thread and thus through the exhaust system but now features a separate earth cable which runs to the engine control unit.Signalmasse SP15-40 Signal earthProbe heater earthProbe heater positiveNote: The voltageless lambda probe is recognizable from the 4-pin connector.The voltageless lambda probe features a defined mass offset.mVProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The control range is raised, which corresponds to the defined mass offset. Advantage:Control range of lambda probeDefined mass offset means:The self-diagnosis is now capable of distinguishing whether the lambda probe is at the control limit (fault in injection system) or whether a short circuit to earth exists.Signal earthDefined mass offsetControl limit reached0Short circuit to earthtSP15-41Note: The earth offset to vehicle earth can only be measured at the 4-pin connector. The voltage readings of the control range, related to signal earth, are displayed in the measured value block of the self-diagnosis. The absolute values of the mass offset in mV differ depending on the engine management system, Refer to Workshop Manual.27 EnginesSystem overview of 1.6-ltr./1.8-ltr. petrol enginesEngine speed sensor G28 and inductive sensorHall sensor G40 Cylinder 1*Hall sensor G40 Cylinder 1**Hot film mass air meter G70Lambda probe G39Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Idling switch F60 Throttle valve positioner potentiometer G88 Throttle valve potentiometer G69Intake air temperature sensor G42 Intake air temperature sensor G42** *Coolant temperature sensor G62Knock sensor I G61 Knock sensor II G66 Additional signals**• A/C compressor • Fan control • Automatic gearbox28 Simos control unit J361 Motronic control unit J220*Fuel pump relay J17 Fuel pump G6**Injectors N30-N33Power output stage with ignition coil 1 and ignition coil 2N122 N N128Solenoid valve for activated charcoal filter N80Lambda probe heater Z19Throttle valve positioner V60Diagnostic connection T16Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Intake manifold changeover with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�*valve N156**Camshaft adjustment valve N205SP15-42• Vehicle speed signal • Fuel consumption signal • Throttle valve signal to automaticg earbox* only for 1.6-ltr. ** only for 1.8-ltr. 29 Engines1.9-ltr. turbodiesel AGRThe TDI principleThe engine features direct injection, exhaust gas turbocharger with intercooler and electronic diesel control. The fuel is injected at a high pressure through five nozzles directly into the respective combustion chamber. The combustion air which has been compressed by the turbocharger and intermediately cooled in the intercooler reaches the combustion chamber through a specially shaped inlet swirl port. This swirl port, together with the combustion chamber the bowl of which is positioned in the piston crown, has a major influence on the entire combustion cycle of the engine.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP15-435-hole injectorThe fuel is injected into the piston bowl in two stages. It ignites on contact with the hot air. The two-stage injection principle avoids a sudden pressure rise.SP15-4430 –Bosch VP 37 EDC distributor injection pump with pump pressure of 800 bar Electronic diesel control (EDC) Exhaust gas recirculation Oxidation catalytic converter Boost pressure control Coolant preheating with electric auxiliary heater Alternator freewheeling EGR valve in intake manifold Valve cover gasket vulcanized in place Oil sump with silicone sealant Replaceable oil filter in the form of paper cartridge Vacuum pump camshaft-driven– –– Special features of the 1.9-ltr. TDI – – – – ––Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Electronic control To satisfy the high demands in terms of fuel economy and emissions, the quantity of fuel injected and the injection timing are controlled with the aid of the electronic system. This task is performed by the Electronic Diesel Control (EDC). It determines the quantity of fuel and start of injection of the distributor injection pump, controls the boost pressure, exhaust gas recirculation and the glow period. On the TDI engine this is the task of the diesel direct injection system control unit J248.SP15-45Diesel direct injection system control unit J24831 EnginesSystem overview of the electronic control of the TDIThe diesel direct injection system control unit J248 accesses maps and characteristic curves in order to ensure the best possible engine characteristics in respect of available torque, fuel economy and emission levels for every operating situation.SensorsNeedle lift sensor G80Engine speed sensor G2840 F/M T-G PBAir mass meter G70G UR RB ANY PIE GERM .01 21 82 7 .1OW FLS US HFL RC DU1 6 46 4 90 07Coolant temperature sensor G62 Intake manifold temperature sensor G72 + Intake manifold pressure sender G71 Brake light/brake pedal switch F/F47unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Clutch pedal switch F36 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedAccelerator pedal position sensor G79 + Idling switch F60 + Kick-down switch F8Modulating piston movement sensor G149 Fuel temperature sensor G81Additional signals• Air conditioning • Terminal DF32 ActuatorsGlow plugs (engine) Q6 Glow plug relay J52 Diesel direct injection control unit J248Heating element (coolant) Q7 Low heating output relay J359Heating elements (coolant) Q7 High heating output relay J360EGR valve N18Boost pressure control solenoid valve N75Glow period warning lamp K29Quantity adjuster N146 Diagnostic connection Fuel shut-off valve N109Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Start of injection valve N108Additional signals SP15-46 • Engine speed signal • Fuel consumption signal • Air conditioning33 EnginesBrief description of mechanical components of the TDISetting distributor injection pump and toothed beltThe toothed belt drives the following components: - camshaft - distributor injection pump - coolant pump Guide pulley Semi-automatic tensioning pulley The belt wrap required is achieved by using two guide pulleys while correct tension is maintained by the semi-automatic toothed belt tensioning pulley.Camshaft sprocketAdjusting toodhed beltCoolant pump Injection pump sprocket Appropriate markings are provided for setting the timing (crankshaft, camshaft, injection pump settings). - Crankshaft setting Crankshaft/top dead centre for cylinder 1 is visible on the flywheel through the inspection hole of the gearbox. A setting device is required if the engine has been removed.Guide pulley Crankshaft toothed belt sprokketSP15-47- Camshaft setting The correct setting is locked with new adjusting straightedge. The precise centre position should be determined with feeler gauges. Exact positioning of the camshaft is of majer importance when fitting on the in toothed belt, for precise valve Protected by copyright. Copying for private or commercial purposes, part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability timing. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� - Injection pump gear The setting of the injection pump is fixed with the locking drift. The injection pump gear is a two-section design. A precision adjustment can be made by slackening the 3 bolts -arrows-.SP15-48Locking drift MP1-301SP15-49 The exact procedure is described in the Workshop Manual for the 1.9-ltr. turbodiesel engine. 34Note: On no account slacken the nut for the hub of the injection pump. If this is done, the basic setting of the injection pump will be altered and can no longer be set with workshop tools. Self-diagnosis and safety concept of the TDI with electronic diesel control EDCDIAGNOSISWhen the engine is running, the control unit performs the following functions: – Comparison of the measurements supplied by the sensors for plausibility. Monitoring system reactions to electrical mechanical operation of the actuators. Monitoring the condition of the electric plug and cable connections for cable break and short circuits.––If faults occur in the system, the EDC reacts in stages in line with the significance of the fault.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Stage 1: In the event of failure of sensors with correction functions, specified substitute values or analysable information of other sensors are adopted. The driver usually is not aware of this.REACTIONStage 2: Major faults which result in the failure of subfunctions, produce a reduction in engine output. The driver is advised of this by the glow warning lamp flashing. Stage 3: If the driver is no longer able to influence the power output of the engine by means of the accelerator pedal, the EDC controls the engine in the fast idling mode. This ensures that sensor functions of the vehicle are maintained. The car can continue to be driven with certain restrictions. Stage 4: If reliable operation of the engine is no longer assured, the engine is shut off by the fuel metering control. Should this not be possible because of the fault, the engine is switched off through the fuel shut off valve (redundant system).35 Engine/Gearbox MountingGearbox mountEngine mountPendulum support SP15-50The engine/gearbox mounting consists of engine mount, gearbox mount and the pendulum support. The engine mount is a hydraulic mount (hydraulically damped rubber bush), while the gearbox mount and pendulum support are designed as bonded rubber bushes. Engine and gearbox mounts are positioned in the rotational axis of the power train about which the engine/gearbox assembly moves when a torque is produced. The pendulum support is located between subframe and gearbox. It absorbs only tensile and compressive forces. It is rigidly attached to the gearbox and flexibly connected to the subframe.Housing Benefit of this type of mounting: Forces act in 3 directions on the engine and gearbox mounts. These forces are absorbed in the direction in which they are effective. The vibrations of the engine/gearbox are well absorbed in the large rubber bushes and prevented from reaching the body. The hydraulic mount minimizes resonance vibrations which could result in the engine/ gearbox "bouncing".RubberProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA SP15-51 AUTO A. S.�Supporting arm36 The principle of the engine/gearbox mountingThe mounting of the engine and gearbox is based on the principle of a pendulum. As a result of the torque produced by the engine the engine/gearbox perform a pendulum motion. This pendulum motion is limited and damped by the pendulum support which is located between the subframe and gearbox.Engine mountGearbox mountEngine support Engine/ Gearbox Gearbox bracket Pendulum support SP15-52 Direction of travel Engine/gearbox in initial position Engine/gearbox performs a pendulum motion as a result of the torque Engine/gearbox swings into initial positionEngine mountGearbox mount SP15-53 Direction of travelNote: Important note for the Service Sector - when bolting the engine/gearbox mount supporting arms to the brackets, the engine and gearbox mounts must not be twisted; - the engine/gearbox should be aligned at the side so as to achieve a clearanProtectedmount by copyright.and Copying for private or bracket. commercial purposes, part or in whole, is not permitted ce of 10 mm between engine engine Theinsupporting unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability arms have slots for this purpose. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�37 Gearboxes5-speed manual gearbox 02 KManual gearbox and final drive form a single component. Gearbox assignment in accordance with engine torque and speed is based on code letters which are affixed together with the date of manufacture of the gearbox to the gearbox housing.Engine Engine code letters Gearbox code letters1.6-ltr. 55 kW AEE CZE1.6-ltr. 74 kW AEH CZD1.9-ltr. 50 kW AGP CZBFlywheel Clutch lever Pressure plateProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�CrankshaftGearbox code lettersRelease bearing Clutch pushrod SP15-54The clutch is operated hydraulically. The slave cylinder presses on the clutch lever which is attached at the gearbox end. The clutch pushrod moves longitudinally through the input shaft. The release movement is transmitted to the clutch through the clutch lever, the release bearing and the clutch pushrod.Note: The clutch is assembled in the reverse order. The pressure plate is bolted to the crankshaft. The flywheel faces toward the gearbox.38 The gearshift movements (selecting and shifting) are transmitted through a shift rod. The coupling rods are provided to minimize vibrations at the gearshift lever.Selector leverShift rod Coupling rod SP15-55Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�39 Gearboxes5-speed manual gearbox 02JThis manual gearbox is fitted with the following engines:Engine Engine code letters Gearbox code letters 1.8-ltr. 92 kW AGN CZM 1.9-ltr. 66 kW AGR CZLFeatures of the clutch mechanism: The clutch is operated hydraulically. The slave cylinder is located at the gearbox housing and presses on the clutch release lever. The clutch is operated through the release bearing.ClutchSlave cylinderProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Clutch release leverRelease bearingSP15-56The shift movement (selecting and shifting) is transmitted by two cables.1R3524SP15-57 40 The hydraulic clutch mechanismAdvantages of a hydraulic clutch mechanism compared to the conventional cable-operated clutch:– Reduced pedal forces and shorter pedal travel which remain the – – – –same over the entire life of the clutch. Improved efficiency as a result of reducing the friction losses. Softer operation of pedal when releasing clutch. Reduced transmission of noise and vibration from the engine. Self-adjusting clutch pedal play.Brake fluid reservoirClutch release leverPressure pipeSlave cylinder Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Master cylinder unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Clutch pedal SP15-58The hydraulic clutch mechanism consists of the master cylinder (positioned at the pedal assembly), slave cylinder (at gearbox) and brake fluid reservoir. Master and slave cylinders are connected by a pressure pipe. The hydraulic clutch mechanism operates with brake fluid. When the clutch pedal is depressed, the hydraulic pressure is transmitted by the master cylinder along the pressure pipe to the slave cylinder. Bleeding is performed in the same way as for the brake system.41 GearboxesAutomatic gearbox 01MThe following engines can be fitted optionally with an automatic gearbox.Engine Engine code letters Gearbox code letters The automatic gearbox is a 4-speed gearbox with electronic control.1.6-ltr. 74 kWAEH DLU1.8-ltr. 92 kWAGN DLRIt automatically performs the task of movingoff, selecting gears (ratios) and shifting gears. A hydrodynamic converter (torque converter) is used as the starting-off element.SP15-59Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee accept any liability Oil or pump with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Planetary gear Intermediate gear stageGearbox design The automatic gearbox has the following main assemblies: – – – – Torque converter with lock-up clutch Oil pump Planetary gear with clutches and brakes Intermediate gear stage (the park lock is located on this) Final drive with bevel gear differentialTorque converter–SP15-60 Lock-up clutchA mechanical connection between engine and gearbox is produced by the lock-up clutch by means of a clutch lining. This eliminates any torque converter slip (torque converter slip = difference in rotational speed between input engine speed and output speed of torque converter). The power of the engine is transmitted mechanically practically 100%.42 The electronic control is performed by the Automatic gearbox control unit J217.The control unit processes information in accordance with a set programme of drive situation circuits (fuzzy logic) The shift point is then computed automatically and varies according to the driving situation and resistances.J 217–Individual adaptation of shift points in all driving situations.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted – unless Changes in shift points in authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness information in this document. Copyright by ŠKODA AUTO A. S.� the case of uphillofor downhill sections are selected as a function of accelerator pedal position and vehicle speed.SP15-61The control unit features a fault memory. This enables faults to be precisely located using the self-diagnosis. In the case of critical faults which occur when driving, the gearbox is operated in the "emergency running mode". In the case of control unit failure, 1st, 3rd and reverse gears can continue to be engaged manually and the car can start off in position "D". Protection agains car moving off unintentionally A mechanical lock in the gearbox is activated in selector lever position "P" as a safeguard when the car is parked. The driving gears are blocked when the selector lever is in this position. The ignition key can be withdrawn only in this position. After this, it is no longer possible to shift the selector lever out of position "P". Selector lever lock A solenoid at the selector lever releases the selector lever only after the brake pedal is depressed when the ignition is switched on. It is now possible to engage a drive position. If the brake pedal is not depressed, it is not possible to shift the selector lever out of positions "P" or "N".43 Running GearOverviewThe SKODA OCTAVIA has independent suspension and also coil springs at the front and rear. Front suspension with McPherson strut, rear suspension with springs and dampers located in line. An anti-roll bar at front and rear reduces the tendency of the body to roll.Disc brakes are fitted as standard at the front with drum brakes at the rear (disc brakes also at the rear with the 92 kW engine version).The suspension, the anti-roll bars (18x3 mm or 21.7x3 mm) and the brake design are matched to the particular engine.All models feature power-assisted steering.The steering column is adjustable forward/back and for height.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP15-62The OCTAVIA can be fitted with 14" and 15" wheels. The wheels are attached with 5 wheel bolts M14x1.5 with spherical collar (hole circle diameter 100 mm). The spare wheel is the same as the standard wheels and is stowed in the boot.Engine output kW50, 55, 74Tyre size175/80 R14Disc wheel6J x 14 H2 steel 6J x 15 H2 steel 6J x 15 H2 light alloy 61/2J x 15 H2 light alloyOffset depth38 mm50, 55, 66, 74, 92195/65 R1538 mm66, 74, 92205/60 R1543 mm44 Front suspensionWheel location features a McPherson strut with wishbone arm and subframe. Cast swivel bushes are used. The wishbone arms are mounted in a subframe which is bolted to the body assembly.McPherson strutClamp connectionSP15-63 Subframe Coupling rod Swivel bushWishbone armProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�A bolt connects the shock absorber tubes by means of a clamp connection - as is familiar from the Felicia - to the swivel bush. The suspension is supported at the top at the body by means of a rubber bush. A new principle has been selected for the pivoting of the anti-roll bar: Positioned in front of the steering gear and located by means of the joint shaft. The anti-roll bar is linked to the wishbone arm by coupling rods. The advantage of this arrangement is a short leg length at the anti-roll bar with higher efficiency combined with a smaller anti-roll bar diameter (smaller distance from pivot point of shoulder bearing to the coupling rod offers greater torsion at the anti-roll bar with the same spring compression).45 Running GearSubframe The subframe is attached to the body by four bolts. The rear connection points are embedded in a rubber bush. This design absorbs the structure-borne sound which would be transmitted to the body supporting bracket.Wishbone arm Front connection point of subframeBody supporting bushSubframeLine of intentional bucklingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted point unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. Rear S. does connection not guarantee or accept any of liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�subframeSP15-64Extremely comprehensive test results have been incorporated in the design of the subframe. The subframe is "crash-optimised". The subframe buckles along an intentional line - behind the connection point of the wishbone arm - downward if subjected to a certain force. This is followed by a specific absorption of the energy in a crash by intentional permanent deformation of the subframe to protect the passenger cell and the side members. Caster A caster of 40 mm has been adopted to reduce the traction influences on the steering and to achieve excellent straight-running characteristics. The steering efforts required for this caster setting (the larger the caster, the greater the effort required for steering) is compensated for by the power-assisted steering. Steering roll radius A negative roll radius of 19 mm (with a wheel offset depth of 38 mm) has a positive effect on directional stability when braking. Service work on front suspension – No adjustment operations are required in the Inspection Service. When carrying out repairs after an accident, inspect the entire suspension geometry. – Wheel toe can be corrected by up to 2 mm at the wishbone The steering joint is mounted in slots for this purpose. – The position of the subframe can be altered by up to 4 mm. This modifies the camber on the right and left side. – No adjustments are possible at the top body support.46 Rear suspensionThe rear suspension is a trailing arm torsion beam design with anti-roll bar. Arranging the springs and shock absorbers in line one behind the other increases the through-loading width of the luggage compartment compared to a conventional suspension strut. The axle beam is bolted at two points to the floor assembly and is supported by the coil spring at two points to the body. The shock absorbers operate as gas-filled shock absorbers.Support at wheelhouseBearing bracket and rubber bush in plastic housingAxle beamBolted connection to floor assemblyProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Anti-roll bar SP15-65 No spring dome in the interiorConstructive features of the axle mounting for improving comfort: There is no connection to the interior through the spring and shock absorber. The spring is located below the side member in the vehicle. This arrangement has a positive effect on noise transmissions, fewer noises are transmitted to the interior of the car. The top pivot point of the shock absorber - at the wheelhouse but outside of the boot - also reduces the level of noises transmitted. The connection at the front to the floor assembly is by means of a rubber bush angled by 25° in a plastic housing at the bearing bracket to achieve a wheel toe correction. As a result of these measures the attachment of the axle beam to the body is acoustically decoupled. Rolling noises from the wheels are suppressed.Spring located below side memberSP15-66 47 Running GearRear suspension when subjected to cornering forceDirection of travel25°with wheel toe correctionWhat does cornering force mean?without wheel toe correctionWhen the car is cornered, there is generally a change in wheel toe as SP15-67 a result of the effect of the cornering force and a certain steering effect of Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability the rear suspension. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� This effect is compensated for by angling the position of the bearing point in connection with the special design of the rubber bush. If the suspension is tending to shift as a result of the cornering force, it is supported by a rubber shoulder at the angled bearing bracket. Cornering is thus optimised. These design details are rendered ineffective if the components are incorrectly installed. Note: The rubber bushes have a wheel toe-correcting effect and therefore have to be installed the correct way round. The bush has an orientation stud and bead for this purpose. These should be aligned to the edge of the steering link. A special tool is provided.Bearing bracketSteering linkOrientation stud/beadSP15-68Edge of steering linkNote: It is not necessary to set the rear suspension. The slots provided in the bearing bracket are intended only as an installation aid.48 Radnabe identical bearing outer raceNew !Two-row grooved ball bearing with bearing inner raceWheel mounting - one wheel bearing unit The wheel bearing unit is a two-row grooved ball bearing. It consists of the bearing inner races, the balls and the wheel hub which at the same time is the outer running surface for the balls. The wheel bearing unit is press-fitted onto the axle stub and bolted with a twelve-point collar nut. It is not necessary to set the bearing play, this exists itself radially and axially in the bearing. The brake drum is fitted on separately.SP15-69Note: The brake drum can be removed separately when carrying out work on the brakes; the wheel hub remains on the axle stub. No further influencing of the operation of the wheel bearing, no further setting of play when carrying out work on the brakes. When the wheel hub is pulled off, the wheel bearing unit is destroyedProtected and must not be reby copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by unit. ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability installed. Use a new wheel bearing with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� The wheel bearing unit is screwed onto the axle stub with the new assembly tool MP. It is essential to tighten the twelve-point collar nut to the correct torque .49 Running GearSteeringThe SKODA OCTAVIA is equipped as standard with a power-assisted steering. The steering servo assistance is a hydraulic system. The steering system includes the following components - power-assisted steering gear with track rods bolted to the subframe - mechanical vane pump - supply pipes for feed and return flow - expansion tank (reservoir).Steering gearSubframe SP15-71The operating principle of the power-assisted steering is the same as that known from the FELICIA system. The pressure in the power cylinder of the steering is as high as 100 bar.Note: The track rod end has a pitch ratio of 1 : 5 at the taper. When carrying out repairs, it is essential to use only the relevant genuine replacement parts. The track rod ends do not have a self-locking effect. When carrying out repairs, counter-hold with a hexagon socket wrench (arrow).New !The power-assisted steering Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted gear cannot be repaired. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability It should be replaced complete. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP15-7250 Steering columnThe steering column is attached to the central tube which is bolted to the two A pillars. It operates through 2 universal joints with a joint shaft to the steering gear. The universal joint shaft is mounted on the steering pinion. The universal joint shaft is a telescope design for this purpose. A cross bolt is used as a locking element. The universal jo