TECHNICAL DOCUMENTATION
SSP 038 Skoda Octavia Model Year 2001

This PDF is currently unavailable.
Read document text
Model year 2001 NEWProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP38_45Since its introduction, the ŠkodaOctavia has proven to be an increasingly successful car. Its clean and elegant lines and, in particular, its engineering excellence, have convinced ever more customers. It goes without saying that continuous further development is important for the success of such a car. An updated ŠkodaOctavia will be available to customers in Model Year 2001. The ŠkodaOctavia incorporates a range of new features concerning not only the interior and exterior, but also, in particular, aimed at improving its engineering prowess. This booklet is aimed at providing you with a first preview of these new engineering highlights.2GBContentsNew Features at a Glance Engines ŠkodaOctavia RS Design Elements Electrical System Brakes Body Safety New 1.6-ltr./75 kW engine Rain Sensor Navigation Seat Adjustment with Memory Extended Service Interval European On Board Diagnosis - EOBD 4 8 9 10 13 21 22 23 24 26 29 30 32 33Servicexxxxxxxxxxxxxxxx OCTAVIAServicexxxxxxxxxxxxxxxx OCTAVIAServicexxxxxxxxxxxxxxxx OCTAVIAService Servicexxxxxxxxxxxxxxxx OCTAVIA xxxxxxxxxxxxxxxx OCTAVIAService Servicexxxxxxxxxxxxxxxx OCTAVIA xxxxxxxxxxxxxxxx OCTAVIAS e r v i c eXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXYou will find notes on inspection and maintenance, setting and repair instructions in the Workshop Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Manual.with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB3New Features at a GlanceDesignNewly designed centre section of dash panelModernised front endProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Headlights in clear glass optic with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Turn signals in clear glass optic4GBNewly designed dash panel insertProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Now also rear window wiperRear light unit – with clear glass elementsMiddle seat now also with head restraint and 3-point seat belt – depending on equipmentSP38_14GB5New Features at a GlanceEngineeringRain sensorPDynamic navigationAutomatic headlight beam control for headlights with gas discharge bulb66P P3 P PP 661SP38_414 2 1 5 4 3SP38_49SP38_01Seat height adjustment with memoryProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�1 23MEM OFFSP38_40Body structure optimised for strengthSP38_77SP38_83 SP38_84 SP38_74MK60 brake control system 6Extended service intervalGBEntry warning lights – depending on equipmentDash panel insert / Optic / Technology Electric immobiliser 3rd generation (certain models)SP38_06 SP38_07 SP38_87New CAN databus systemGatewaySP38_08J17SP38_67J234 J…J393 SE SESE SE Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability M with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� G6EOBDSP38_10Special functions in event of a crashHC CO NOxEuropean On Board Diagnosis systemSP38_35SP38_44Now also rear window wiper 7GBEnginesVersionsPetrol engines 1.4-ltr./44 kW 1.4-ltr./55 kW 1.6-ltr./55 kW 1.6-ltr./74 kW 1.6-ltr./75 kW 2.0-ltr./85 kW El. throttle yes yes no no yes no Emission standard EU 2 EU 4 EU 2 EU 2 EU 3D/ECE (Pb) EU 4 ECE (Pb) TIER-1 Engine management Simos 3PB ME 7.5.10 MM 1LV Simos 2.1 Simos 3.3 M 5.9.2 M 3.8.5Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 2 M 3.8.5 unless authorised by ŠKODA AUTO A. S. ŠKODA EU AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�yes 1.8-ltr./110 kW yes no 1.8-ltr./132 kW Diesel engines 1.9-ltr./50 kW SDI 1.9-ltr./66 kW TDI 1.9-ltr.74 kW 1.9-ltr./81 kW yes El. throttle yes yes yes yesEU 4 EU 3/EU 4 EU 2 EU 4 Emission standard EU 3 EU 2/EU 3 EU 3 EU 2/EU 3ME 7.5 ME 7.5 M 3.8.3 ME 7.5 Engine management EDC 15 V+ EDC 15 V+ EDC 15 V+ EDC 15 V+The versions listed in the table reflect the status as at 08/00.8GBŠkodaOctavia RSThe new sporty ŠkodaOctavia RS features for the first time the powerful 1.8-ltr. T 132 kW engine in a ŠKODA model.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP38_75Technical data Type: 4-cylinder inline engine with turbocharger 1781 cm3 81 mm 86.4 mm 9.5 : 1Displacement: Bore: Stroke: Compression ratio: Rated output: Max. torque:132 kW at 5500 rpm 235 Nm at 1950-5000 rpm Multipoint injection (MPI) EU 4/2 Unleaded petrol ROZ 98 (95)1000 2000 3000 4000 5000 6000Mixture formation mélange: Emission standard: Fuel:SP38_70GB9Design ElementsFront and rear endshave undergone very subtle updating in terms of shape and design. At the front this relates to the headlights, the bumper moulding with the three pronounced air inlets and the turn signal lights. the bumper moulding has been adapted to the larger headlights with their slightly modified shape. The headlights now feature clear glass optic. The 2001 model is recognisable at the rear from the tail lights with clear glass elements.Front viewSP38_16Rear viewProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP38_1710GBLightsHeadlights The headlights used reflect the general trend to adopting new clear glass optic. They feature clear light beam lenses without diffuser screens. The light beam lenses are made of plastic. The reflector, a single-part design, is divided into 2 chambers. The diffusing of the light is achieved by appropriately shaping the reflector chambers. Depending on the equipment version, gas discharge bulbs (xenon bulbs) are used in addition to the familiar halogen bulbs. The headlights then have a slightly modified inner design.Standard headlight versionMain beam/low beam Fog lightSP38_18Side lightHeadlight with xenon bulbMain beam (halogen bulb) Low beam (xenon bulb)SP38_65Fog light Side lightRear light units The new rear light units also feature segments in clear glass. These are the light beam segments for the turn signal light and reversing light.Turn signal lightBrake lightSP38_19Reversing lightRear fog light/tail lightFront turn signal lightsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The familiar positioning of the turn signal lights has been maintained. The turn signal lights are incorporated in a separate housing and have clear light beam lenses.SP38_20The bulb of the turn signal light is coloured.Turn signal lightGB11Design ElementsDash panel insert A new feature is – the position of the display symbols. They are no longer all positioned within the central large display, but, for the most part, in the facias of the instruments. the design of the facias of the instruments (e.g. scale division).SP38_07–Dash panel The familiar arrangement in the upper part of the dash panel has been retained. In contrast, a smooth transition has been adopted for merging with the centre console. This is not only more elegant, but also more ergonomic as it eliminates the previous edges.SP38_523 head restraints/3 seat belts at rear Depending on the equipment version, the rear middle seat now also features a head restraint. In addition, this seat on models fitted with a head restraint, is also equipped with a 3-point seat belt.SP38_4312Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBElectrical SystemCAN databus systemThe CAN databus system familiar from the OCTAVIA, has been restructured.RadioCANGatewayEngine control unit J…AC control unit J301ABS/TCS control unit J104Convenience Parking aid system central control unit J446 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability control unit J393 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�K wireAutomatic gearbox control unit J217Driver-side door control unit J386Passenger-side door control unit J387Radio and navigation control unit with display unit J503CANAirbag control unit J234Rear left door control unit J388Rear right door control unit J389Left/right gas discharge light control unit J343/344CANDriver-side seat/ mirror position control unit J394SP38_08A transmission rate of 500 kbit/s has been selected for the drive databus subsystem in order to ensure rapid data transfer within the safety-relevant systems. A transmission rate of 62.5 kbit/s is adequate within the convenience CAN databus subsystem.CAN (switched) Drive CAN (500 kbit/s) Convenience CAN (62.5 kbit/s) K wireGB13Electrical SystemDash panel insertSP38_07The following are integrated in the dash panel insert: – – – – – – – –Self-diagnosisThe dash panel insert has a diagnosis Control unit J218 capability, the address word being "17". Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Immobiliser control unit unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO S.� The following components can beA. tested Speedometer using final control diagnosis: Rev counter Fuel gauge – Rev counter Coolant temperature gauge – Fuel gauge Warning lights – Coolant temperature gauge Multifunction display – Speedometer – Display readout – Fuel reserve warning light – Coolant temperature warning light All the warning lights are fitted with LEDs. No – Brake system warning light provision is made for repairs in the event of a fault. In such a case, the dash panel insert should be replaced. All the information relating to monitoring functions, are processed in the control unit of the dash panel insert and transmitted to the warning lights which come on for a certain time, flash, or come on and remain on. In addition, a gateway as a link for the CAN databus systems, is also integrated in the dash panel insert.Note: If the dash panel insert is replaced, it is then necessary to carry out adaptation of the other vehicle systems.14GBEntry warning lightDepending on the equipment version, both doors feature a warning light. The entry warning light is operated through a door contact switch. A relay ensures that, if the vehicle is parked with a door opened (e.g. in a garage), the light remains on only for a limited time. This ensures that there is no unnecessary drain or discharging of the battery.SP38_06Entry warning lights fitted to the front doors of the vehicle make a significant contribution to making an opened door more visible to the driver of a vehicle coming up from behind. They substantially enhance road safety and make a significant contribution to a reduction in the accident risk.SP38_04ImmobiliserWith the introduction of model 2001 of the OCTAVIA, certain equipment versions are fitted with a new immobiliser with programmable code, immobiliser III (3rd generation).Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP38_87This considerably enhances security against theft.GB15Electrical SystemGas discharge lightsGas discharge lights are also used on the new OCTAVIA, depending on the equipment version. As required by legislation, such lights are installed only in combination with an automatic headlight beam control. The light in a gas discharge bulb is generated by a light arc between two electrodes in a glass bulb filled with gas. The glass bulb bulges in the area of the light arc, to approximately the size of a pea. The composition of the gas is a criticalProtected by copyright. Copying private orspectrum commercial purposes, in part or in whole, is not permitted element for the for colour (colour) of unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability light. The colour spectrum of xenon gas withthe respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Light arcdischarge lights closely approximates the colour spectrum of daylight, more so than that of halogen bulbs.SP38_72Function The gas discharge light requires a highvoltage pulse of several thousand volts for igniting the light arc. This voltage is generated in the ballast. The high-voltage pulse produces a light arc which ionises the gas. After ignition has taken place, the gas discharge bulb is operated with an increased current for a few seconds to enable the bulb to reach its maximum brightness in the shortest possible time. After this, the ballast controls the flow of current to the bulb. The gas discharge bulb operates as a lowbeam light. When the driver switches over to main beam, the main beam halogen bulb is then switched on. Consequently, gas discharge bulb and halogen bulb operate together. Note: Gas discharge bulbs must be replaced only by a Škoda dealer or qualified workshop. Do not grasp such lights in the area of the glass bulb, but only at the base of the light.The main components of headlights fitted with gas discharge bulbs are: – – headlight housing, gas discharge bulb (low beam), halogen bulb (main beam), bulb for side light and fog light (depending on equipment), headlight beam control unit, ballast for gas discharge bulb, and the headlight beam control motor– – –16GBLight patternam2020 40bm20Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�20 40m 240180120600SP38_71a = Car fitted with halogen bulbs b = Car fitted with gas discharge bulbsAdvantages – The light yield is some 2.5 times higher than conventional light, with the same power consumption. Thanks to the specific design of reflector, shield and lens it has been possible to achieve a significantly extended range of the light beam and a considerably wider spread of light in the short-distance range. This has made it possible to improve the illumination of the road surface, which in turn reduces driver fatigue in conditions of poor visibility. The life of a gas discharge bulb is about 2500 hours, several times that of a conventional halogen bulb.Diagnosis The gas discharge headlights and the headlight beam control system have a diagnostic capability. Address word "29" left headlight Address word "39" right headlight The following functions are possible: 01 - Interrogating control unit version 02 - Interrogating fault memory 03 - Final control diagnosis 04 - Basic setting, using address word "29" 05 - Erasing fault memory 06 - Ending output 07 - Coding control unit 08 - Reading measured value block––GB17Electrical SystemHeadlight beam controlThe OCTAVIA was also previously fitted with a headlight beam control. This had to be adjusted by the driver manually, however, and it was possible only to compensate for an additional payload by altering the angle of the headlights in stages. It was not possible to allow for variations in the beam range of the headlight caused by braking or accelerating.Thumbwheel of headlight beam controlSP38_78On a vehicle fitted with conventional halogen bulbs, the headlight beam range is altered manually by turning the thumbwheel for the headlight beam control.Altering the headlight beam range with manual headlight beam controlVehicle stationary, driving at constant speed, without loadSP38_03kgAccelerating or with load at the rearSP38_32BrakingSP38_33Automatic headlight beam controlDespite the fact that the light yield of a xenon bulb is as much as 2.5 times greater, the glare On vehicles fitted with gas discharge lights, caused to oncoming traffic is reduced to a the beam range is controlled automatically. minimum as a result of the automatic headlight control. Protected by copyright. Copying for private or commercial purposes, in part or in whole, isbeam not permitted authorised byrequirement ŠKODA AUTO A. S. Š KODA AUTO A. S. does not guarantee or accept any liability This isunless a statutory if a vehicle is with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� fitted with such lights, and also better takes The system of automatic headlight beam into account real-life conditions in daily control automatically varies the range of the motoring. light cone constantly when driving.18GBThe system of automatic headlight beam control4 2 1 534SP38_011 Headlight with positioning motor and control unit for headlight beam control 2 ABS control unit and vehicle speed signal 3 Control unit of dash panel insert 4 Sensor for vehicle level RL (rear left) 5 Sensor for vehicle level FL (front left)The colour of the light alters after it is switched on, beginning with bluish tones through to approximately white (after about Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 30 s) unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Function Each time the ignition is switched on, the reflectors of the headlights together with the bulbs are set to the lowest beam range, and then to the beam range required at that moment, both when the lights are "ON" or "OFF". To achieve the correct setting, the system analyses the signals supplied by both sensors, one of which is mounted at the rear left, and the other at the front left axle. This analysis is carried out in the control unit of the left headlight (master). The information required is transmitted over electric cables to the right-hand headlight. If the vehicle is stationary, the system reacts immediately to any change in the attitude of the vehicle compared to the road level, e.g. if occupants get in or if a load is placed in the vehicle. After setting off, the signals supplied by the two sensors are constantly analysed. The system detects whether the vehicle is accelerating or braking. The setting of the headlights is then adjusted accordingly. The system forms and stores an average value from the signals analysed.GB19Electrical SystemComponents of the system The relative motions when the springs of the suspension system compress are transmitted by means of a lever system to the sensors attached to the front and rear axles. The sensors in turn now signal to the control unit of the headlight beam control system (at the left-hand headlight) the change in the attitude of the vehicle. Variations from the specified position are analysed in the control unit and the position of the headlights is altered by the positioning motors. Substitute function in the event of system failure: In the event of a failure of system components such as – – – – gas discharge bulb headlight beam control unit ballast sensors, etc.or if an open circuit exists in the wiring, a "backup value" is computed from the average value calculated during the trip, and is used as a substitute value for moving the headlights into the safety position.Headlight with gas discharge bulb, control unit for headlight range and positioning motorSP38_79Sensor for vehicle level RL Sensor for vehicle level FLSP38_81SP38_80Note: If the control unit for the automatic headlight beam control fails, the headlights and bulbs move into the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted safety which minimises unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. position does not guarantee or accept any liability with respect to the correctness of information in this document. by ŠKODA AUTO A. S.� dazzle ofCopyright oncoming traffic.20GBBrakesMK60 control systemThe new MK60 in different configurations is used for the first time at ŠKODA in the OCTAVIA 2001. – – – – ABS (+ EBC) TCS/EDL (+ EBC) ESP (+ EBC) ESP/4 x 4 with engine of 110 kW or moreABS, TCS/EDL, ESP control unit with hydraulic unitThe design and management of the system have been optimised, although the fundamental operating principle does not differ from the familiar MK20 system. MK60 is used on all OCTAVIA models, with the exception of vehicles fitted with four-wheel Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability drive without ESP.with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP38_74What is new in comparison with the familiar MK20?–MK60 makes it possible to use ESP also on 4x4 models. ESP functions have been optimised (smoother control and software harmonisation). The braking distance has been shortened by some 3 %. A more compact design offers a weight saving for the entire system of some 1.5 kg.–The pressure for ESP is produced solely by the hydraulic pump; the active servo unit is no longer required. On the version with ESP, the brake master cylinder has only one pressure sensor. When the MK60 control unit is coded, allowance is made not only for the engine fitted and the activated functions of ABS, EDL etc., but also for the suspension version used. All vehicles fitted with ESP also feature disc brakes at the rear, irrespective of the engine or gearbox installed.–––––– – The installation position in the vehicle and the mounting of the system have been modified. The hydraulic unit features valves with a faster response.–GB21BodyOptimising the body structureThe tried-and-tested body of the OCTAVIA has undergone revision and design optimisation at individual points. The new elements incorporated in the body are intended to reinforce the structure and to contribute to a further increase in body stiffness. The stiffeners also have a favourable impact on handling characteristics and on behaviour in the event of a crash.Roof stiffenerCorner stiffenerSP38_54SP38_53SP38_77B pillarFront end Additional sheet metal panels are in Protected by copyright. Copying for private or welded commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. Š KODA AUTO A. S. does not guarantee or accept any liability place between suspension strut domes and with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� plenum chamber as corner stiffeners. Roof The body has been equipped with a new roof stiffener which is positioned between the left and right B pillars. B pillar This pillar has undergone a redesign and, at the same time, higher-strength materials are now used.SP38_5822GBSafetySpecial functions in the event of a crashThe safety system of the OCTAVIA features automatic circuits in the event of a crash which help to minimise the risks of an accident situation.J17J234Three actions are triggered: – – – the central locking system is unlocked the interior light is switched on the fuel feed is shut offJ…J393 SE SEOperating principle The crash sensor in the airbag control unit J234 is activated by the deceleration resulting from a crash. The signal passes along a cable link from the airbag control unit J234 to the convenience system central control unit J393. The doors are unlocked and the interior light is switched on. Different methods of transmitting signal for shutting off fuel: –SEMSEG6SP38_10= Signal flow on engines without CAN databus system = Signal flow on engines with CAN databus systemOn engines without CAN databus system SE = Locking units in doors (1.4-ltr./55 kW and 1.6-ltr./55 kW) the signal passes simultaneously from the airbag = Interior light control unit J234 to the fuel pump relay J17. This results in the voltage supply to J… = Engine control unit the fuel pump G6 being interrupted and the fuel feed to the engine shut off. Protected is by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted J234 = Airbag control unit– On engines with CAN databus systems, the signal passes simultaneously through the drive CAN to the engine control unit. This in turn transmits a signal to the fuel pump relay and the fuel supply is likewise shut off.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�J393 = Convenience system central control unit J17 = Fuel pump relay G6 = Fuel pumpGB23New 1.6-ltr./75 kW engineThe new 1.6-ltr./75 kW engine (code letters AVU) is used for the first time in the OCTAVIA 2001. It features an overhead camshaft (OHC), variable intake manifold and a knock sensor. The cylinder head and cylinder block are manufactured from light alloy. A particular technical highlight is the electronically controlled cooling system. This system allows for the fact that an optimal operating temperature in all engine load ranges is a major factor in determining engine power output and pollutant emissions. The electronically controlled cooling system makes it possible to optimise the curve of the engine operating temperature. Features Type Displacement Bore Stroke Compression ratio Max. output Max. torque Mixture formation Emission standard Technical data 4-cylinder inline engine 1595 cm3 81.0 mm 77.4 mm 10.5 : 1 75 kW at 5600 rpm 148 Nm at 3800 rpm Multipoint injection (MPI) EU 4 Unleaded petrol RON 95 (91)The temperatures in the part-load range. This in turn achieves improved fuel consumption and exhaust emission levels.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Fuel unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� engine operates at increased operatingAs a result of the lower temperatures in the full-load range, the inducted air is heated up to a lesser extent. This in turn boosts the power output of the engine.Performance (saloon) Max. speed Acceleration from 0 to 100 km/h 190 km/ h 11.8 s 7.0 l/100 kmThe engine load-dependent specified values for the electronic control of the coolant temperature are stored in maps in the engine control unit.Fuel consumptionAir massVehicle speedSpecified temperatureEngine speedSpecified temperatureIntake air temperatureSP38_85SP38_8624GBElectronically controlled cooling circuit – schematic diagram An engine with an electronically controlled cooling system is characterised by the following features compared to an engine with a conventional cooling circuit: – The cooling circuit features a separate thermostat for map-controlled cooling of the engine (with additional resistance heater). Self-diagnosis The electronically controlled cooling system is integrated in the self-diagnosis of the engine control unit.– Coolant distributor housing and thermostat form a single unit. – The coolant thermostat at the engine block is not required. The engine control unit additionally features the maps of the electronically controlled cooling system.–Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability reservoir with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�ExpansionCoolant distributor housingCoolant pumpOil cooler (if automatic gearbox fitted) Thermostat for map-controlled engine coolingOil cooler (engine circuit)Feed Return flow RadiatorSP38_89GB25Rain SensorThe rain sensorWhen the windscreen wipers are switched on, the rain sensor detects that it is raining and transmits matching signals to the intermittent wash/wipe relay J31. The relay automatically controls the length of the wipe intervals. The rain sensor is located in the base of the interior rear-view mirror.Rain sensorSwitchSP38_12The sensitivity of the rain sensor can be individually set by means of a switch.SP 38_64Position of sensorBase of cable duct cover Windscreen Cable duct coverProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Gel layer Base plate Cover for rain sensor Rain sensorNote: The gel layer allows the infrared rays to pass through without the usual refraction at a boundary surface.Base of mirrorSP38_13Rear-view mirror 26GBOperating principle The reception diode is positioned in the middle of the rain sensor. A total of 8 transmission diodes are positioned evenly around the reception diode. A rubber ring between reception diode and transmission diodes separates these from each other and prevents the rays striking the reception diode other than intended. The transmission diodes of the rain sensor are subdivided into two groups each containing 4 diodes. Each of these alternately transmits infrared rays and the diodes are positioned in such a way that, if the windscreen is dry, 100 % of the rays transmitted are reflected on the outer surface of the windscreen to the reception diode (total reflection).Base plate Rain sensorSP38_49Base of mirrorIn the same way as in the transmission mode, the rays of the one or other group of diodes are radiated alternately onto the reception diode. So long as the intensity of the reflected rays of both groups does not differ, no voltage is produced at the reception diode. This corresponds to the reflection of a dry windscreen.Dry windscreenTransmission diode Windscreen Reception diode Transmission diodeSP38_50Wet windscreen The refraction conditions change if the windscreen is wet. In this case, some of the rays are refracted and directed out, the remaining weakened part is reflected in to the reception diode. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability The alternately strongly reflected unless rays with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� produce a voltage at the reception diode. The sensor transmits matching signals to the intermittent wash/wipe relay J31, and the windscreen wipers are switched on. The length of the wipe intervals is adapted automatically in line with the quantity of rain.SP38_51GB27Rain SensorFundamentals The rain sensor makes use of physical laws relating to the refraction of rays in the transfer from one medium to another. In certain circumstances, the rays are not transferred from one medium to the other, but are in fact fully reflected – this is known as total reflection. Whether total reflection occurs, depends on the angle of refraction. The angle αg is known as the critical angle of total reflection. Its matching angle of refraction is β = 90o. The condition for total reflection is met in the case of all angles of α αg, in this case the waves are fully reflected. Refraction occurs at angles of α αg.Reflection and refraction on a flat boundary surface (schematic diagram)Glass (windscreen)unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Transmission with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� diodeProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedReception diodeSP38_21Rain sensorIf the refraction conditions at the boundary surface change, for example because of rain, part quantities of the rays may flow out of the glass despite the fact that the angle conditionfor total reflection is maintained, and the remaining reflected rays are in this case weakened.SP38_2228GBNavigationNavigation systemP 66P P3 P PP 661Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP38_41The C navigation system which has been available up until now in the OCTAVIA, is supplanted by a new D navigation system. The unit is designed from the outset for "dynamic navigation". It is possible to exploit the possibilities offered by "dynamic navigation" with the system at any time by retrofitting a TMC box and adapting the system accordingly.Dynamic navigation is a system which receives and displays traffic congestion messages over the TMC. TMC is the abbreviation of Traffic Message Channel. This is a traffic channel in the radio data system (RDS) which transmits traffic information nationally in an inaudible digital form by radio.Features of the system: – Compared to the previous C navigation system, the D navigation system features a more powerful processor The mechanical design of the CD ROM drive has been optimised CD ROMs from C systems cannot be used in the D navigation system, although the reverse is possible.The new unit is recognisable on the outside by the: – – ŠkodaAuto inscription at the top left DX inscription at the top right– –GB29Seat AdjustmentSeat Adjustment with memoryThe ŠkodaOctavia model 2001 is equipped with an intelligent technical solution for setting the seat. To avoid having to expend time and effort setting the driver's seat and the matching exterior mirrors (for driving forward) each time another driver takes the car, the seat setting of the driver's seat has been equipped with a memory function. It is now possible, therefore, to store up to 3 different settings and to re-activate these subsequently for a new setting.1 23MEM OFFSP38_40CDThe seat and mirrors can be set or the setting retrieved both manually using the control panel – switches A, B – electrically operated seat setting123MEM OFF–Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted pushbuttons C – 3 memory buttons for unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability storing/retrieving a setting for driver's seat with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� and mirrorsSP38_61–locking switch D – for deactivating or activating the memory systemABas well as by radio using the opening button of the remote control.SP38_6230GBFunction for memory of driver seatCMemory for driver seat – – The following are detected: Setting of driver's seat Setting of exterior mirrors1 23DMEM OFFABSwitching system off and onSetting SystemSwitchesA, BStoring SettingRetrieving SettingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Retrieving with memory functionRetrieving with remote control keyWith locking switchWith pushbuttonWith pushbuttonWith pushbuttonWith Off button of remote control keyDonly manual setting possible; system is reactivated by again pressing switch.Cstoring current setting on memory buttons; for retrieving with remote control key, a button must be assigned in each case to key.Cif driver door open, briefly press desired memory button ... setting is performed automatically.Cif driver door is closed, press and hold desired memory button until system setting is completed. setting of driver seat and of exterior mirrors is performed after driver door is opened.SP38_59GB31Extended Service IntervalExtended service intervalThe ŠkodaOctavia model 2001 is also equipped with engines which benefit from the longer intervals which are now possible for servicing – the so-called extended service interval (ESI). The extended service interval is based on a variety of technical further developments and makes it possible to achieve a substantial increase in the periods between individual services. The driver is informed in good time of the distance which still remains until the next service is due. He can influence the period until the next service for the vehicle is due by optimising his individual style of driving and also the operating conditions so as to achieve the longest possible periods between a service. He is provided with visual information regarding oil level and the next service due.Components of the ESIPb1J0915105ACNew elementsOil quality Engine oil sensor Brake wear indicator Low-maintenance batteryExtended Service Interval New serviceProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Flexible service display Oil level calculated from Distance Oil temperature Fuel consumptionNew analysis and informationSP38_2332GBEuropean On Board DiagnosisEuropean On Board DiagnosisModel Year 2001 of the ŠkodaOctavia features the new European On Board Diagnosis system EOBD. During the initial phase, this relates only to vehicles equipped with petrol engines which comply with the EU 4 standard. Introduction on diesel engines will follow in the foreseeable future. EOBD is an adaptation of the OBDII system which is already familiar from the USA, and has been harmonised with the legal provisions of the European Union.E O BDSP38_34Basic concept of EOBD Malfunctions and faulty components can result in a considerable increase in the pollutant emissions of vehicles. It is therefore desirable to constantly and directly measure the concentration of pollutant components when the vehicle is operated. As it is not possible to achieve this aim at present except with considerable technical cost and effort, the engine management system is utilised for monitoring the exhaustrelevant components. The advantage of this is that faults can be detected directly using a diagnosis data reader.EOBDSP38_36HC Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability CO unless with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� NOxSP38_35Note: Please refer to Self Study Programme 39 "European On Board Diagnosis" for more detailed information.The new emission warning light indicates to the driver whether there is a malfunction of a diagnosis component which is relevant for exhaust emission levels.GB33NotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�34GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB35