TECHNICAL DOCUMENTATION
SSP 049 2,5 114kW TDI V6 Superb

This PDF is currently unavailable.
Read document text
SP49_02The 2.5-ltr./114 kW TDI V6 Diesel Engine A new era of diesel begins at ŠKODAFor the first time a diesel direct injection engine with 6-Cylinder in V-construction is fitted in a Škoda passenger car. The engine is designed fundamentally with the already known elements From the series 2.5-ltr. V6 TDI Engines with 110/132 kW. With this engine, Škoda sets new standards with the installation of a diesel engine in a passenger car. The 4-valve method is the emphasized characteristic of the engine besides its V6 structural shape. The engine combines very good driving performance with low consumption and exhaust emission as well as an excellent smoothness of running and high comfort. However, the apparent contrasts are balanced, like sportive driving on the one hand and an environmentally conscious mobility as well as a large range on the other hand.2Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBContentsIntroduction Technical data Technical characteristics Component Positions Overview Engine Mechanics Crankcase and crankgear Differential shaft Valve gear Camshaft drive Engine Mounting Engine mount Engine Lubrication Oil circulation system Crankcase Ventilation Crankcase ventilation Engine Cooling Coolant circuit Viscous fan coupling Fuel Supply System System of fuel supply Radial piston distributor injection pump Travel of fuel Engine Management Overview of system Communication of control units Fuel quantity control Start of injection control Turning angle sensor G208 Oil temperature sender G8 Fuel shortage sender G210 Overview of system components Glow Plug System Introduction Function Diagram Legend to function diagram Self-diagnosis Self-diagnosisServicexxxxxxxxxxxxxxxx SUPERB4 4 5 6 6 8 8 11 13 14 16 16 18 18 19 19 20 20 21 24 24 27 28 30 30 32 33 35 39 39 40 41 43 43 44 46 47 47Servicexxxxxxxxxxxxxxxx SUPERBServicexxxxxxxxxxxxxxxx SUPERBService Servicexxxxxxxxxxxxxxxx SUPERB xxxxxxxxxxxxxxxx SUPERBService Servicexxxxxxxxxxxxxxxx SUPERB xxxxxxxxxxxxxxxx SUPERBS e r v i c eXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability You can unless find information regarding andby ŠKODA AUTO A. S.� with respect to the correctness of information ininspection this document. Copyright maintenance, setting and repair instructions in the Workshop Manuals.GB3Introduction150 5001354501204001053509030075 P (kW)250 M (Nm)6020045150SP49_0330100155001000200030004000500060007000n (min –1 )SP49_04P = Power output M = Torque n = Engine speed Technical Data Engine code letters Displacement Bore Stroke Compression ratio max. Power output Torque Engine management Firing order Fuel Exhaust aftertreatment Exhaust emission standard4AYM 2496 cm3Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�78.3 mm86.4 mm18.5 : 1 114 kW at 4000 min–1 310 Nm at 1400 … 4000 min–1 Bosch EDC 14M 1-4-3-6-2-5 Diesel fuel at least 49 CZ Biodiesel at least 48 CZ Oxidation catalytic converter EU3GBDrive gear of radial piston distributor injection pump Oil filter Toothed belt for radial piston distributor injection pumpInjection nozzleCamshaft inlet side Camshaft outlet sideToothed belt for camshaftsOil cooler Chain tensioner CrankshaftSP49_23 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Hydraulic chain tensioning elementOil pumpDifferential shaftTechnical characteristics – – Cylinder banks below angle of 90° High pressure direct injection via radial piston distributor injection pump with two spring nozzle holder 4-valve method Injection nozzles centered to cylinder and positioned vertically Camshaft drive via toothed belt Valve control through 2 overhead camshafts per cylinder bank (DOHC) Valve control via cam follower, supported on hydraulic valve clearance compensation elements – – – – – – Turbocharger with the control through adjustable turbine vanes, without bypass Charge air cooler Exhaust gas recirculation Oil pump assigned in the oil pan is driven from the crankshaft via the chain Differential shaft Hydraulic engine mount, electrically actuated– – – – –GB5Component positionsOverviewVacuum box for charge pressure (mechanical) Oil pressure switch F1Oil temperature sender G8Solenoid valve for charge pressure control N75Air mass meter G70 with intake air temperature sender G42 (in top part of air filter housing)Injection nozzle with needle stroke sender G80Glow plugs Q6Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Coolant temperature unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability sender G62 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Injection pump with: Control unit for injection pump J399, Metering adjuster N146, Start of injection valve N108, Fuel temperature sender G81, Turning angle sensor G2086GBExhaust gas recirculation valve (mechanical)Fuel pump relay J17 Glow plug relay J52Diesel direct injection system control unit J248 with integrated altitude sender F96Diesel direct injection system relay J322Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Engine speed sender G28Change-over valve for intake manifold flap N239SP49_29Exhaust gas recirculation valve N18Glow plugs Q6Intake manifold pressure sender G71 Vacuum box with intake manifold flap (mechanical)GB7Engine MechanicsCrankcase and crankgearA low overall height is reached through a 90˚ V- structure. Enough space is left at the same time between the cylinder banks for the location of further components. A quiet zone for the crankcase ventilation, which is locked with an aluminum cover, is located between the cylinder banks. The thermostat and coolant pump housing are integrated in the front side of the crankcase. A short overall length is reached through this and through an 18.5 mm low offset of the cylinder rows. The crankcase is manufactured from grey cast iron.Coolant pump housingSP49_84Quiet zone for crankcase ventilationThermostat housingCrankshaftCross-boltingThe crankshaft is mounted four times. The crankshaft bearing caps are bolted four times to the crankcase. The load of the bearing caps is therefore considerably reduced.SP49_30The centered bearing caps are additionally bolted in transverse direction on both sides with the crankcase for reinforcement.Advantage: Improved engine acousticsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Large counterweights on the crankshaft and a differential shaft ensure the most optimal balance of mass.CrankshaftSP49_278GBCrankshaft journal offset For a V6 engine the equal firing distance of the cylinders amounts to 120˚. A 30˚ offset of the three crankshaft journals is necessary because of the V- angle of 90˚ between both cylinder banks. The effect of the crankshaft journal offset On each offset (split) crankpin, the conrods are located for Cylinder 1 and 4 Cylinder 2 and 5 Cylinder 3 and 6 Firing order: 1 - 4 - 3 - 6 - 2 - 5SP49_28Positioning of crankpin of cylinder 4 at OT of cylinder 190°Cylinder 1Cylinder 430The crankpin of cylinder 4 lags behind the crankpin of cylinder 1 by 30˚°SP49_24… Crankshaft rotation by 120˚Cylinder 1Cylinder 4 Original positioning of crank journal of cylinder 4 at OT of cylinder 1Positioning of crank pin of cylinder 4 at OT of cylinder 4120°Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability SP49_25 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB9Engine MechanicsPiston The piston is fitted with a ring shaped cooling duct which reduces the temperature in the area of the ring and at the edge of the combustion cavity of the piston. Oil is injected into the piston via an oil injection nozzle to the ring shaped cooling duct and thus cools the piston. The oil is delivered directly from the oil pump via an oil duct to the oil injection nozzle. After this, it drains off the piston again.Ring shaped cooling duct Piston injection nozzleSP49_81Conrod The engine is equipped with trapezoidal conrods.Bearing shellConrod eye (trapezoidal shape)Note: Please refer to the Self Study Programme No. 36 for further information on the trapezoidal conrods.ConrodSP49_82Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The top and bottom bearing shells are fitted as “Sputtered bearing”. Sputtering is the popping of a bearing material with the help of electrical energy. Through the acceleration of particles of the bearing material from the anode, the bearing material is transmitted with supersonic speed highly compressed onto the carrier material (cathode) of the bearing shells. This very thin vacuum evaporated sliding layer shows a high surface hardening and an improved resistance to wear.Vacuum pumpAnode Bearing materialAr+High voltageSP49_86Bearing shellCathode10GBDifferential shaftThe differential shaft has the function to balance the tumbling motions of the engine.Differential shaftForces are created in the upper and lower dead centre when pistons are moving up and down. These forces operate in various long lever arms toward the center point of the crankshaft and thereby produce moments.SP49_10PistonProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Conrod unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Center pointSP49_34CrankshaftSP49_33In a 4 cylinder in-line engine the piston forces function to top and bottom. The moments neutralize each other because two pistons are located in the top dead centre and two in the bottom dead centre.In a 6 cylinder V engine the piston forces function in direction of the legs of the V angle toward the peak point. Therefore the moments cannot balance.If the moments cannot balance, they set the engine into a tumbling motion. In a diesel engine, the tumbling motion is stronger than in a comparable Otto engine, because the weight of the pistons and conrods is greater.SP49_35GB11Engine MechanicsTo avoid tumbling, the engine is equipped with a differential shaft. The differential shaft has two differential weights, which are positioned on the shaft rotated toward each other at 180˚.Differential weight Differential shaftSP49_10Differential weightCrankshaftThe differential shaft is positioned in the top part of the oil pan and is driven from the crankshaft via a chain. The chain grips from below into the drive gear of the differential shaft. As a result of this, it turns in opposite direction to the direction of rotation of the crankshaft.Differential shaft with differential weightsSP49_11Drive gear CrankshaftThe unbalanced moments of the engine are Protected by copyright. Copying for private or commercial purposes, in parttensioner or in whole, is not permitted Chain opposed to the moments of identical size, by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does unless authorised not guarantee or accept any liability with rotation respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� because of the opposite direction of and the differential weights. This avoids the tumbling motion of the engine. Differential shaft The chain is tensioned via the chain tensioning element. The chain tensioning element is hydraulic. It is connected to the engine oil circuit. The chain and the chain tensioning element are free of maintenance.Chain tensioning element (hydraulic) Oil pump Guide pinionSP49_1212GBValve gear4 valve conceptFilling duct (for quick filling of cylinder at high rpm)Swirl duct (for good swirl)Injection nozzleInlet valveY-pipe ductOutlet valveSP49_32The engine is fitted with the 4-valve method already known from the Otto engine. The shape and location of the inlet ducts ensure good filling and swirling of the intake air in the combustion chamber and thus a good fuel preparation. Low exhaust emissions are obtained besides good combustion. Two inlet and outlet valves are each assigned to the injection nozzle at the central and vertical piston axle.The position of the injection nozzle guarantees, together with the middle piston combustion cavity, that the fuel is distributed equally in the combustion chamber. The valves are positioned in such a way, that each of the two camshafts operates an inlet as well as an outlet valve per cylinder.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB13Engine MechanicsCamshaft driveOne camshaft is driven via the toothed belt per cylinder head. The second shaft is driven via an angular toothed spur gear set. The camshafts run in a cylinder bank in opposite direction of rotation. Each camshaft operates three inlet and three outlet valves. In addition to this, the vacuum pump is driven via the camshaft inlet side of the left cylinder bank.Spur gear Camshaft inlet sideCamshaft sprocketToothed beltSP49_26Camshaft Toothed beltThe camshafts must be adjusted toward each other. The adjustment is obtained with the camshaft fixer (adjusting straightedge). The spur gears are assigned to the right cylinder bank on the side of the fly-wheel and to the left cylinder bank on the side of the toothed belt.Adjusting straightedgeProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Note: You can find information regarding adjustment of timing in the Workshop Manual.SP49_71Spur gear14GBAdjustment of toothed belt To adjust the timing of the valve drive, the piston of the 3rd cylinder must be situated in the upper dead centre. This position is visible with a marking on the camshaft in the area of the oil filler inlet. The fixing screw locks the crankshaft into the secured position.Fixing screwSP49_78Right cylinder headMount ofbearing cap The camshafts of each cylinder bank must vacuum pump have a defined position toward each other. This position is achieved through the camshaft fixers when installing the camshafts.Protected The by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability corresponding locking slots are located on the with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� side of the spur gear of the camshaft.When replacing the toothed belt, the camshaft fixers are inserted into the bearing cap of the right cylinder head and in the mount of the vacuum pump at the left cylinder head.SP49_79Note: You can find information regarding adjustment of toothed belt in the Workshop Manual.GB15Engine MountingEngine mountTwo hydraulically damped engine mounts guarantee in the total area of the speed, that the engine vibrations are damped effectively and are not transmitted to the body. The damping is designed for both operating conditions, idling as well as engine load operation.Engine mountSP49_63Upper chamber Air duct to Rubber metal housingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted atmosphere unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Solenoid valve for electrohydraulic engine mounting N144/N145SP49_18Lower chamberRubber diaphragm Rubber bellow Nozzle duct Plastic bodyHydraulic oil Air (atmosphere) 16GBFunction The solenoid valves for the electrohydraulic engine mounting N144 and N145 are activated by the engine control unit. Idling operation At engine speeds up to 1100 min–1 bearing is flexible.Upper chamber Rubber diaphragm Air duct to atmosphereThe solenoid valve is opened by the engine control unit. The hydraulic fluid in the upper chamber is pressurized according to the engine vibrations, because of the small high frequency vibration paths of the engine. The small vibration paths of the engine cannot press the hydraulic oil through the nozzle duct. Therefore the pressure of the hydraulic SP49_19 oil has an effect on the rubber diaphragm. Protected It by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability deforms and expels the air out of the opened with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� air duct.Nozzle ductEngine load operation At engine speeds of more than 1100 min–1 bearing is hard. During driving, the small and large low frequency vibration paths of the engine superpose. The solenoid valve is closed by the engine control unit. Therefore the air cannot escape below the rubber diaphragm and creates an air cushion. This air cushion is a great resistor for the hydraulic oil, which is already under pressure in the bearing. The hydraulic oil is now pressed via the nozzle duct into the lower chamber. The rubber fellow deforms and through this the large vibration paths of the engine are removed.Lower chamberRubber diaphragmSolenoid valveSP49_20Injection duct Rubber fellowNote: The large low frequency vibration paths of the engine are accentuated through the road which leads to the engine oscillating. The vibration paths become larger and the oscillating of the engine becomes stronger, if the electrohydraulic damped engine mount is defective.GB17Engine LubricationOil circulation systemTurbocharger Oil temperature sender G8 Oil pressure switch F1 Short circuit valve Oil filter Return-flow check tube Vacuum pump Valve compensation elementSpray nozzle valve Pressure limiting valveCamshaftPressure limiting valvePiston spray cooling Piston spray nozzle Oil pressure regulator valve Oil pump Oil pan Oil coolerPressure relief valve Differential shaftSP49_13Oil flow with pressureOil flow with reduced pressureOil flow without pressureElements of oil circulation system The oil pump The oil pressure regulator valve The pressure relief valve … is a crescent pump. It is positioned in the oil pan. … regulates the oil pressure of the engine in the housing of the oil pump. … is a safety valve. It is located in the housing of the oil pump and opens when the oil pressure is high (cold start). The return-flow check tubes … avoid, when the engine is standing in still motion, that oil flows out of the oil filter and the cylinder heads back into the oil pan. They are located in the cylinder block and in the oil filter housing. The short circuit valve … opens when oil filter is plugged and through this secures the oil supply of the engine. The oil cooler … is integrated in the main oil flow. The spray nozzle valve … guides oil for cooling the pistons to the piston spray nozzles. The pressure limiting valves … avoid an overflow of the cylinder heads by reducing the oil Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability flow. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�18GBCrankcase VentilationCrankcase ventilationThe crankcase ventilation is designed as a compact unit, consisting of the oil filter and the oil separator. When engine is running, one part of the gases, which was compressed in the cylinder, reaches the piston rings in the crankcase. There is then an overpressure in the crankcase which must be removed. The removal of the pressure is performed through the crankcase ventilation. When ventilating, oil particles are carried along through the gas circulation. The crankcase ventilation system has corresponding components, which will stop these oil particles from entering the intake manifold. Pressure regulating valve - openedOil separator Air to intake manifoldOil filterSP49_61Pressure regulating valve Collecting tank To oil pan Gases from crankcaseFunction The gases mixed with oil flow into the oil separator. The oil is filtered out in the oil separator that is made of fabric. Then it flows into the collecting tank and from here back into the oil pan. Finally the cleaned gases are lead into the intake manifold. If the negative pressure is too high in the crankcase, it can result in damages to the crankcase seal. The pressure regulating valve prevents, that the negative pressure is too high in the crankcase. It consists of a rubber diaphragm and a spring. If the negative pressure is too high in the intake manifold as well as in the crankcase, then the pressure regulating valve closes the connection of the oil separator to the crankcase. If the negative pressure is low in the intake manifold, the pressure regulating valve opens through the force of the spring.Pressure regulating valve - closedPressure regulating valveSP49_62Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB19Engine CoolingCoolant circuitWhen engine is cold, the coolant does not flow through the cooler. In this case, the engine reaches faster its operating temperature. The coolant flows through the cylinder banks in such a way, that first of all the area of the inlet valves is cooled per cylinder. This is thermally more advantageous, because the intake air in this area is not warmed up unnecessarily and the volumetric efficiency of the cylinders is reduced. Notes: Pay attention to the notes for filling and ventilation of coolant circuits in the Workshop Manual. The thermostat opens the large cooling circuit and closes simultaneously the connection from the right cylinder bank to the thermostat housing.ATF - coolerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Coolant pump ThermostatHeat exchangerExpansion reservoirCoolerSP49_59Viscous fan couplingEngine oil coolerVentilation lineSmall cooling circuit Large cooling circuit 20Note: The cooler for automatic transmission oil (ATF) is integrated in the cooler.GBViscous fan couplingThe fan for the engine cooling is regulated, depending on the temperature, via a viscous fan coupling. This means, that the fan only works, if an additional engine cooling is required. The viscous fan coupling is free of maintenance. The adjuster screw must not be wrongly adjusted. Design and function The viscous fan coupling consists of two rooms: – The work room with the drive pulley which is connected to the flange shaft, as well as the – storage room with the intermediate washer, which is frictionally connected to the basic body. The intermediate washer has a valve opening. The valve lever is fastened to the intermediate washer and depending on the temperature, it opens and closes the valve via bimetal and shift pin. The viscous oil circulates via the pump body/ overflow duct in the cover and via the valve opening in the intermediate washer between work room and storage room. The more viscous oil is in the work room, the larger is the frictional connection between the drive pulley and the basic body and the higher is the fan speed. Advantages: – more engine performance – less fuel consumption – less noiseBasic body CoverValve openingDrive pulley Bimetal Valve lever Adjuster screw Intermediate washerShift pin Flange shaft Seal Work room Storage room with viscous oil Pump bodySP49_85Overflow ductProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Pump body with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Cover with shift pin and seal Bimetal with adjuster screwIntermediate washer with valve lever Drive pulleyBasic body with flange shaftSP49_66GB21Engine CoolingThe diagrams for the speed of the fan and the drive performance correspond in principle to all operating conditions of the engine cold/ warm/hot. When the temperatures at the bimetal are higher and at a drive speed as of approx. 5.500 min–1, the speed of the fan decreases because of the lower viscosity of the viscous oil (inner friction).4000AFan speed (min–1]3500 3000 2500 2000 1500 1000 500 0 0 1000 2000 3000 4000 5000 6000 7000 8000BDrive speed [min–1] Drive performance [kW]4,00 3,50 3,00 2,50 2,00 1,50 1,00 0,50 0 0 1000 2000 3000 4000 5000 6000SP49_65AA - The clutch is fully engaged at a temperature of approx. ≥ 75˚C at bimetalB7000 8000Drive speed [min–1]SP49_64B - The clutch is fully disengaged at a temperature of approx. ≤ 40˚C at bimetalEngine cold When rotating the drive pulley, the viscous oil bounces in the work room against the pump body and is pumped via the overflow duct into the storage room. The valve lever, which operates via the bimetal/shift pin, closes the valve opening, so that no viscous oil can flow back into the work room. When the work room is free of oil, no frictional connection exists any more between the drive pulley and the basic body. The fan rotates only with a low speed (inner friction).Valve closedBimetal (in starting position)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP49_67Engine drive Fan drive Viscous oil22GBValve opening slightly releasedValve opening fully releasedBimetal (slightly bent)Bimetal (fully bent)Drive engine Fan drive Viscous oilSP49_68SP49_69Warm engineHot engineThe more the ambient temperature increases When the ambient temperature at the bimetal Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted at the bimetal the more it bends outward. high, bends more the outside. For unless authorised by Šis KODA AUTO it A. S. ŠKODA AUTO A. S. to does not guarantee or accept anythis liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Now the valve lever can lift a little from the reason, the stroke of the valve lever increases. intermediate washer because of its initial The valve opening is fully released and more pretension and can slightly release the valve viscous oil flows into the work room so that opening The viscous oil can flow into the work the maximum speed of the fan is reached. room. For this reason, a connection develops In this operating condition, the differential between the drive pulley and the intermediate speed between the drive pulley and the washer/basic body. intermediate washer/basic body is at its The speed of the fan increases. The viscous oil lowest. is pumped over between the work room and Therefore the smallest quantity of viscous oil the storage room via the pump body/overflow is pumped out of the work room into the duct. The pumped over oil quantity is storage room. dependent on the differential speed of the drive pulley and the intermediate washer/ basic body.GB23Fuel Supply SystemSystem of fuel supplyFuel filter Control valveRadial piston distributor injection pumpSP49_22Fuel tankInjection nozzleMFuel tank Suction jet pump Return flow FeedTechnical data: – Contents of fuel tank 62 ltr. – Injection pressure of injection nozzles 185 MPaTwo versions exist for the fuel supply: – Two part banking up housing with electrical fuel pump and suction jet pump One part banking up housing with predelivery pump The fuel filter cleans the fuel before it reaches the radial piston distributor injection pump because a little contamination in the fuel can already damage the radial piston distributor injection pump.–The radial piston distributor injection pump The fuel quantity control is performed in the must suction fuel which is free of bubbles. To radial piston distributor injection pump. do this, it does not suction the fuel directly out of the fuel tank but out of the banking up housing. Functions control valve: Protected by copyright. Copying for of private or commercial purposes, in part or in whole, is not permitted In order to guarantee a secure flow of the radial piston distributor injection pump, the volume in the banking up of housing, in both versions, must always be filled with fuel. If the fuel level in this volume risks to drop because of an empty fuel tank, the fuel shortage sender G210 sends a signal to the engine control unit J248 to switch off the injection system. This avoids damage to the radial piston distributor injection pump. – When the fuel temperature is below 15 ˚C, the control valve opens the feed of the fuel return flow to the fuel filter, in order to avoid a build-up of paraffin. When the fuel temperature is above 30 ˚C, the control valve opens the feed of the fuel return flow to the fuel filter, in order to avoid vapor lock. Then the fuel flows back into the fuel tank.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�–24GBTwo part banking up of housing with electrical fuel pump and suction jet pump The two part banking up of housing with an electrical fuel pump is located in the fuel tank.Fuel tankTwo part banking up of housing with electrical fuel pumpSuction jet pumpSP49_74O u ter and inne r part of ba nking up o f h o u sing The electrical fuel pump is located in the outer part of the banking up of housing. The line, through which the fuel is delivered is separated into two single lines. The fuel is delivered through the line to a narrow chamber in the inner part of the banking up of housing.Narrow chamberElectrical fuel pumpMThe fuel flows from the narrow chamber over into the inner part of the banking up of housing. The fuel is suctioned from here through a radial piston distributor injection Inner part of pump. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted The fuel is delivered through the second line into the suction jet pump. S u c t ion jet pum p The fuel jet which flows out the nozzle of the suction jet pump causes at this point a lower pressure – Venturi effect. For this reason, the fuel jet draws further fuel out of the fuel tank into the outer part of the banking up of housing. This guarantees that the banking up of housing is always filled with fuel, even if only a small quantity of fuel is left in the fuel tank.SP49_102banking up of unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� housingOuter part of banking up of housingSuction jet pumpFuel jet Suction jet pumpSP49_100Inner part of banking up of housingGBDrawn fuel 25Fuel Supply SystemThe function of the suction jet pump is based on a simple physical principle. This principle was discovered by an Italian physicist Giovanni Battista Venturi (1746 1822) = Venturi Effect. Later this effect was mathematically described by the Swiss Daniel Bernoulli (1700 - 1782) = Bernoulli’s equationFlowing fluidv1 A1 A2v2 p2∆pV ent ur i Ef f ect For the flow of a fluid through a tapered pipe applies, that at the narrowest point the flow rate of the fluid is at its highest and the static pressure is at its lowest. At a narrowing point of the pipe the flow rate must automatically increase, because the same amount flows out of the end of the pipe than flows into the front of the pipe.p1Measuring fluidSP49_101A1 v1 p1 ∆p A1v1 = =A2 v2 p2 p1 – p2 A2v2A1, A2 Cross-sectional area v1, v2 Flow rate p1, p2 Static pressureA2 – Point with the lowest static pressureOne part banking up of housing with predelivery pump On the one-part banking up of housing with pre-delivery pump, the electrical pre-delivery pump delivers the fuel out of the fuel tank into the banking up of housing. The fuel is suctioned off from there, free of bubbles, from the radial piston distributor injection pump. The suction jet pump is not needed.Fuel tankProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP49_75One part banking up of housing with predelivery pump26GBRadial piston distributor injection pumpIn comparison to the mechanical or electronic regulated axial piston distributor injection pump, it has a higher dynamic at the volume and start of injection control and produces pressures up to 185 MPa. The delivery of the fuel is performed through a vane-type delivery pump. The high pressure is produced through a mounted radial piston high pressure pump. In order to determine the adaptation of the start of injection, the control unit for the injection pump J399 registers and evaluates the signals from the turning angle sensor G208 and the fuel temperature sender G81. These components are parts of the radial piston distributor injection pump.Radial piston high pressure volume Turning angle sensor G208 Inner room of pump Drive shaft Distributor shaftSP49_90Control unit for injection pump J399 with fuel temperature sender G81Metering adjuster N146 (Solenoid valve for adjusting control)Valve for start of injection N108 Vane-type delivery pumpSP49_37Cam ring Injection timing device Cam ring Pressure in inner room of pump High pressureDistributor shaft RollerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Roller shoe Delivery pistonGBHigh pressure volumeSP49_70bFor the V6 Diesel Engine 2.5-ltr./114 kW TD in the ŠkodaSuperb a radial piston distributor injection pump with 3 delivery pistons is used.27Fuel Supply SystemTravel of fuelSuction A vane-type delivery pump which suctions fuel out of the fuel tank and creates a corresponding pre-pressure in the pump (inner room of pump), is positioned in the radial piston distributor injection pump. The pressure build-up through volume diminution is achieved with the eccentric mounting of the vane-type delivery pump.Vane-type delivery pump DrainTo inner room of pumpFeed from fuel tankSP49_40High pressure volumeFuel feed out of inner room of pump Metering adjuster N146 (solenoid valve)When the metering adjuster N146 is open, the fuel, because of its pressure build-up, is pressed via the internal pump connection into the high pressure volume of the radial piston high pressure pump.Pressure build-upDistributor shaft Roller Delivery piston Fuel Cam ringSP49_41Fuel compressedSP49_42SP49_43unless authorised by Š KODA AUTO A. S. Š KODA AUTO A. S. does guarantee or accept anythe liability The distributor shaft is driven via the drive The rollers runnot on the cam of cam ring. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� shaft of the radial piston distributor injection The delivery pistons are pressed in the radial pump. direction to the inside and therefore a very When rotating the distributor shaft, the high fuel injection pressure is produced. delivery pistons are operated by the cam ring.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted28GBDistribute If the metering adjuster N146 is closed, the fuel from the high pressure volume of the radial piston high pressure pump is distributed from the distributor shaft via the hole in the hydraulic head assembly into the return flow throttle valve and the injection nozzle of each cylinder.Distributor shaftMetering adjuster N146 (solenoid valve)Injection nozzle High pressure volumeSP49_44Hydraulic head assemblyHoleReturn flow throttle valveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Distributor shaftHydraulic head assemblyIn the hydraulic head assembly holes are located, which are allocated to the individual cylinders. The distributor shaft turns with the drive shaft of the radial piston distributor injection pump and connects the high pressure volume one after another with one hole each in the hydraulic head assembly.HoleSP49_45High pressure volumeGB29Engine ManagementOverview of systemAir mass meter G70 with intake air temperature sender G42 (in upper part of air filter housing)Sensors0 40 /M4 F/M T-G T-GF PB RG BU Y AN PIERGERM 1 1.0 22 7 .18OW FLSS LU HF RC DU1 6 46 4 90 07Engine speed sender G28Diesel direct injection system control unit J248 (engine control unit)Needle stroke sender G80Accelerator pedal position sender G79 with Kick-Down switch F8 and idling switch F60Coolant temperature sender G62Intake manifold pressure sender G71 CAN DriveBOSCHOil temperature switch G8Brake light switch F and brake pedal switch F47Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Clutch pedal switch F36 Control unit for injection pump J399 Fuel temperature sender G81 Metering adjuster N146 Start of injection valve N108 Turning angle sensor G208Fuel shortage sender G210Auxiliary signals: Generator terminal DFM Vehicle speed signal CCS switch AC compressor “On” AC readiness30GBActuatorsGlow plugs Q6Glow plug relay J52Change over valve for intake manifold flap N239Solenoid valve for charge pressure control N75 W - wireExhaust gas recirculation valve N18GatewayProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Left solenoid valve for electrohydraulic unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability mounting N144Copyright by ŠKODA AUTO A. S.� with respect to the correctness of information in this document.engineRight solenoid valve for electrohydraulic engine mounting N145K - wireGlow period warning light K29Diesel direct injection system relay J322Fuel pump relay J17Diagnostic connectionAuxiliary signals: AC compressor “Off” Radiator fan castorSP49_15GB31Engine ManagementCommunication of control unitsThe communication between the diesel direct injection system J248 control unit (engine control unit) and the control unit for the injection pump J399 is performed via the CAN-Bus. The control unit for the injection pump is integrated in the radial piston distributor injection pump.Function diagramPositioning of accelerator pedal Engine speed Intake air temperature Coolant temperature Start of injection Engine control unitCAN-Bus• Injection rate • Start of delivery • Engine speed• Continuous actuation of metering adjuster • Injection pump speed • Fuel temperature • Fault messagesControl unit for injection pumpSignals e.g. for: • Exhaust gas recirculation • Charge pressure controlMetering adjuster Start of injection valve Turning angle sensor Fuel temperature senderInjection pumpSP49_38Data exchange The speed of the injection pump is determined The engine control unit analyses the injection the turning angle sensor. speed is rate (specified value) and the start of delivery Protected by copyright. by Copying for private or commercial purposes, in part This or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. Š KODA AUTO A. S. does notspeed guarantee or accept any liability compared with the engine in the control from the above indicated input signals. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� unit J399. In the case of failure of the signal of the The control unit for the injection pump engine speed sender G28, the injection pump determines from the specified value of the speed is used as a replacement signal for the injection rate the continuous actuation of the engine control unit. metering adjuster. The fuel temperature (determined by the fuel temperature sender in the diesel radial piston distributor injection pump) is used as an additional variable for the calculation of the start of delivery and the continuous actuation of the metering adjuster.Note: The engine control unit has further additional functions, as e.g., the control of the actuators for the exhaust gas recirculation and the charge pressure control.GB32Fuel quantity controlThe fuel quantity control has the function to calculate and add the optimal fuel quantity to the engine in each operating condition. The signal of the injection rate from the engine control unit is evaluated in the control unit for the injection pump and is transmitted to the metering adjuster N146. For the fuel quantity control the following influences must be considered: – Start quantity – Idling control – Driving operation – Smoothness control – Vehicle speed control – Control of quantity limit – Anti-jerk control (when suddenly operating or releasing the accelerator pedal)Accelerator pedal position sender G79 with Kick-Down switch F8 and idle switch F60Diesel direct injection system control unit J248 (engine control unit)Coolant temperature sender G62 CAN-BusAir mass meter G70 with intake air temperature sender G42 (in upper part of air filter Gateway housing) Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted0 /M4 -GF PBTG UR RB NY PIE GERMA 1 1.0 22 7 .18OW FLSS LU HF RC DU1 6 46 4 90 07unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Engine speed sender G28Diagnostic connectionBOSCHControl unit for injection pump J399SP49_16Auxiliary signals: Clutch pedal switch F36 Brake light switch F Brake pedal switch F47Metering adjuster N146GB33Engine ManagementHigh pressure productionFilling phaseThe metering adjuster N146 is open. The rollers run in the cam recesses and the delivery pistons are pressed to the outside.Fuel flows from the vane-type delivery pump into the hydraulic head assembly and fills up the high pressure volume.Fuel feed from the vane-type delivery pump Cam ring Metering adjuster N146 opened (solenoid valve)Roller High pressure volume Delivery pistonSP49_46Deliver y and inje ction pha se The metering adjuster N146 is controlled by the control unit for the injection pump J399 and closes the fuel feed. The rollers run on the cam surveys and the delivery pistons are pressed to the inside. The fuel pressure in the high pressure volume increases rapidly. The individual controlled injection nozzle opens. If the desired injection rate is reached, the metering adjuster N146 is reopened. The fuel pressure in the high pressure volume collapses. When the fuel pressure decreases, the injection nozzle closes again. The fuel injection is completed.Metering adjuster N146 closed (solenoid valve)Injection nozzleSP49_44Note: The metering adjuster N146 has an additional function - switch off the engine. When the ignition is switched offby itcopyright. opens, so for that no more fuel pressure is produced Protected Copying private or commercial purposes, in part or in whole, is not permitted and unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability no more fuel can be injected into the cylinders. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�34GBStart of Injection controlThe start of injection has a large influence on the performance, fuel consumption, noises and exhaust characteristics of the engine. Its specified value which depends on the engine speed and injection rate, is stored in the control unit. Furthermore, a correction of the specified value, depending on the coolant temperature, can also be carried out. The start of delivery is the time at which the metering adjuster N146 closes in the hydraulic head assembly. Its specified value is determined from the specified value of the start of injection. The delay time, which the pressure wave in the wire needs to the individual injection valve, is considered. If the needle stroke sender G80 is defective, the radial piston distributor injection pump can nevertheless be operated (however only with higher start of injection tolerances).The signal of the needle stroke sender G80 is evaluated in order to determine the actual value of the start of injection. The specified value of the start of delivery is corrected accordingly by the engine control unit, if the The start of injection control is performed to actual value of the start of injection differs “early” or to “late”. from its specified value. The signal of the start Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted of delivery from the engine control is AUTO A. S. does not guarantee or accept any liability unless authorised by ŠKODA AUTO unit A. S. ŠKODA with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� evaluated in the control unit for the injection pump and is transmitted to the start of injection valve N108.Diesel direct injection system control unit J248 (engine control unit)Coolant temperature sender G62 CAN-BusGatewayInjection nozzle with needle stroke sender G80Engine speed sender G28Diagnostic connectionBOSCHControl unit for injection pump J399SP49_48Start of injection valve N108GB35Engine ManagementIt functions as follows: Adjust ment to “ e a rly ” In rest position the injection timing piston is held with a restoring spring (“late position”). The fuel pressure is produced in the vane-type delivery pump in the inner room of pump of the radial piston distributor injection pump. It acts as a control pressure via a throttle on the annular space of the hydraulic stop. If the start of injection valve is closed, it moves the control piston opposite the force of the control piston spring in direction of “early” (in fig. to the right). The modulating piston also moves through this to “early”.Distributor shaft Ball studCam ring Roller Restoring springModulating piston Injection timing piston Feed duct/ drain ductControl piston springControl pistonControl hole 1 to metering adjuster Pump drainProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Vane-type unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� delivery pumpAnnular space of hydraulic stop Control hole 2Pump feedSP49_87Feed from fuel tankThrottleStart of injection valve36GBThe control hole 1 is opened through the displacement of the modulating piston and the fuel can flow behind the injection timing piston. Now the fuel presses the injection timing piston toward right in direction of “early”. The axial movement of the injection timing piston is transposed via the ball stud as a movement of rotation onto the cam ring of the radial piston high pressure pump.The angular movement of the cam ring in relation to the drive shaft (distributor shaft) leads, at early timing, to an earlier overrun of the rollers on the cam survey and with this to an earlier start of injection. The possible early timing can amount up to 20˚ camshaft angle (corresponds to 40˚ crankshaft angle).Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Distributor shaft Cam ring unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Ball studRoller Restoring springModulating piston Control piston spring Injection timing piston Feed duct/ drain ductControl pistonControl hole 1 to metering adjuster Pump drain Vane-type delivery pump Pump feed Annular space of hydraulic stop Control hole 2SP49_88Feed from fuel tankThrottleStart of injection valveGB37Engine ManagementA djust ment to “ late ” The start of injection valve opens, if it receives pulsed signals from the control unit for the injection pump. The control pressure decreases through this in the annular space of the hydraulic stop. The control piston moves through the spring force of the control piston spring in direction of “late” (in fig, to the left). The injection timing piston remains at first in still motion. Only when the modulating piston opens the control hole 2 to the drain duct, the fuel can flow out of the space behind the injection timing piston. Now the spring force of the restoring spring presses the injection timing piston again in direction of “late”, in its original position.Distributor shaft Ball studCam ring Roller Restoring springModulating pistonControl piston springInjection timing piston Feed duct/ drain ductProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Control pistonControl hole 1 to metering adjuster Pump drain Vane-type delivery pump Pump feed Annular space of hydraulic stop Control hole 2SP49_89Feed from fuel tankThrottleStart of injection valve38GBTurning angle sensor G208The turning angle sensor measures the angles, which the drive shaft (distributor shaft) of the radial piston distributor injection pump and the cam ring take to each other in the course of the rotation. By means of this, the individual actual speed of the injection pump, the injection timing piston position and the angle position of the camshaft is determined.Control unit for injection pump J399 Turning angle sensor G208 Flexible conductor foilThe turning angle sensor must produce its signal in relation to the angle position of the cam ring. For this reason, it is mounted rotatable on the drive shaft, in contrast to the sensor rotor which is connected firmly with the drive shaft of the injection pump. It rotates Drive shaft simultaneously when the injection timing Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability piston with cam ring is moving. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� The signal of the turning angle sensor is transposed via a flexible conductor foil inside the injection pump to the control unit for the injection pump J399. The momentary angle position determines when the metering adjuster actuator N146 is actuated. Effects of signal failureSP49_52Sensor rotorThe control unit for the injection pump J399 cannot determine the cylinder assignment and the injection pump speed. Fuel can therefore no longer be injected. The engine switches off and does no longer start off.Oil temperature sender G8The oil temperature sender G8 is located in the oil supply line for the turbocharger next to the oil pressure switch F1.SP49_53The signal of the oil temperature sender is used from the engine control unit, in order to monitor the temperature of the engine oil. If the engine oil becomes too hot, the injection rate is reduced in order to avoid damages to the engine.Effects of signal failure The engine control unit uses a firm substitute value. The protective function is only available within limits. The engine runs with a decreased performance.GB39Engine ManagementFuel shortage sender G210The fuel shortage sender is located in the banking up of housing of the fuel tank. The function of the fuel shortage sender is based on the opening and closing of the Reed contacts (contact studs), depending on the position of the float, in which a permanent magnet ring is located. The signal of the sender is used, in order to avoid the fuel system from running empty. This means, it is used as a protection for the injection pump. The radial piston distributor injection pump must always remain filled with fuel, otherwise damages could occur. A dry run of the radial piston distributor injection pump must be prevented, in order to preclude problems resulting from lubrication shortage and to avoid costly venting air.Reed contactsPermanent magnet ringIf the sender G210 reports fuel shortage to the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted engine control unit, it then informs the control SP49_54 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability unit for the injection pump J399. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� After this the control unit for the injection pump J399 switches off the fuel feed through the actuation of the metering adjuster N146. The engine switches off. An engine start is prevented until fuel is refilled.FloatEffects of signal failure When – Interrupting, – Short circuit to earth or – Short circuit to positive in the cable connection to the sender G210 as well as on a defective sender, the glow period warning lamp K29 flashes in the dash panel insert. The protection of the injection pump can no longer be guaranteed. The fuel system can run empty.J248 53 72QG210SP49_9940GBOverview of system componentsNote: Familiar function components which have already been described in detail in previous Self Study Programmes are used for controlling the 2.5-ltr./114 kW TDI V6 Diesel engine.The table refers to the relevant Self Study Programmes. Please make use this detailed information.Function componentFunction description SSP 16 (shows different shape, installation position and function identical) SSP 16 SSP 22Coolant temperature sender G62 It is integrated in the coolant circuit and informs the diesel direct injection system control unit J248 about the actual coolant temperature.SP49_91Accelerator pedal position sender G79 The sender is located at the accelerator pedal. It detects the accelerator pedal position and transmits it to the diesel direct injection system control unit J248. In addition the Kick-down switch F8 and the idle switch F60 are contained in the sender.SP49_92Engine speed sensor G28 The diesel direct injection system control unit J248 analyses through the signal of this sender the momentary engine speed.SP49_93SSP 36 (shows different shape, installation position and function identical)The sender works as an inductive sender.Exhaust gas recirculation valve N18 SSP 16 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted It controls the exhaust gas quantity expelled into 22 unless authorised by Š KODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee SSP or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� fresh air.SP49_94GB41Engine ManagementFunction componentsFunction description SSP 16Clutch pedal switch F36 The signal of this switch influences the injection control when shifting gears. Load impacts are prevented through this when shifting.SP49_95Brake light switch F and brake pedal switch F47 It indicates the signal “brake in operation” to the diesel direct injection system control unit J248.SSP 16 (shows different shape, installation position and function identical)SP49_96Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Change-over valve for intake manifold flap N239 The change-over valve prevents, through closing of the intake manifold flap, anti-jerk movements when switching off the engine.SP49_94SSP 22SP49_94Solenoid valve for charge pressure control N75 The solenoid valve is controlled by the diesel direct injection system control unit J248 according to the charge pressure performance map and serves as charge pressure control.SSP 22Needle stroke sender G80 It is located in the injection nozzle of the 3rd cylinder and serves as detection of the start of injection.SP49_97SSP 16Intake manifold pressure sender G71 The sender is located in the charge air cooler. The signal serves as detection of the charge pressure.SP49_98SSP 1642GBGlow Plug SystemIntroductionAt low temperatures the starting off of the engine is facilitated with the glow plug system. It is switched on by the engine control unit at a coolant temperature below +9˚C. The glow plug relay is controlled by the engine control unit. It switches on the work flow for the glow plugs. The overview of the system shows you, from which sensors signals for the glow plug system are used and which actuators are actuated.Engine speed sender G28Diesel direct injection system control unit J248 (engine control unit)Glow period warning lamp K29 Coolant temperature sender G62 Glow plugs Q6 Glow plug relay J52SP49_55Pre-glowing After switching on ignition at a temperature below +9˚C, the glow plugs are switched on. The glow period warning lamp is illuminated. If the glow procedure is finished, the warning lamp extinguishes and the engine can start off.After-glowing After each engine start is after-glowing which is not dependent on pre-glowing. The combustion noises are decreased, the idling quality is improved and the hydrocarbon emissions are reduced. The after-glow phase lasts max. 4 minutes or ends at an engine speed of over 4000 min–1.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB43Function DiagramJ17J52+ 30+15SB31 15AS125 60AS189 60A J322 J17SB28 20AMQ6G631Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 18 1 32 37 42 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�28073 49 68 301131055372110 102109 101517063 69125031QG42/G70G8G210G28G80F60/F8G7931Legend to Function Diagram see page 46. 44GB+30 +15S131 15ASB13 10A 31E45 N239 N75 N18 N144 N145E227FF47F36 7 2 6 1 J399 8 58162 J248 52 316123144645 4432656682 83 93 114Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�7111210445201629343811671G62 G71234567831in outSP49_58GB45Function DiagramLegend to Function DiagramComponents E45 E227 F F8 F36 F47 F60 G6 G8 G28 G42 G62 G70 G71 G79 G80 G210 J17 J52 J248 Switch for CCS Push-button for CCS (Set) Brake light switch Kick-Down switch Clutch pedal switch Brake pedal switch Idling switch Fuel pump Oil temperature sender Engine speed sender Intake air temperature sender Coolant temperature sender Air mass meter Intake manifold pressure sender Accelerator pedal position sender Needle stroke sender Fuel shortage sender Fuel pump relay Glow plug relay Diesel direct injection system control unit J322 Diesel direct injection system relay J399 Injection pump control unit N18 Exhaust gas recirculation valve N75 Solenoid valve for charge pressure control N144 Left solenoid valve for electrohydraulic engine mounting N145 Right solenoid valve for electrohyraulic engine mounting N239 Change-over valve for intake manifold flap Q6 Glow plugs S, SB…Fuse Auxiliary signals 1 2 3 4 5 6 7 8 Vehicle speed signal W wire AC compressor on/off AC readiness Generator (Terminal DFM) Radiator fan castor CAN Drive (Low) CAN Drive (High)Colour coding = = = = = = Input signal Output signal bidirectional Positive Earth CAN databusNote: The function diagram represents a simplified current flow diagram.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�46GBSelf-diagnosisSelf-diagnosisThe sensors and the actuators are checked in the frame of the self-diagnosis. Please use the up-to-date workshop literature and vehicle diagnosis, testing and information system VAS 5051.Note: Please pay attention, that the Repair group 01 is integrated in the “listed fault finding”. The functions “Reading measured value block” and “Final control diagnosis” are also listed in it.SP49_73Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The color-illustrated components are inspected in the frame of the Self-diagnosis and the listed Fault Finding.40 F/M40 -GF/M PBT PBT-GG BUR ANY PIERGERM 1 21.0 7 .182W FLOG70, G42 G28 G80 G79, G185, F8, F60S LUS CHF DUR 074 906 461Q6 J248 J52 N239N75 G62 G71 G8 F, F47 F36 J399 G210 J17BOSCHN18GatewayN144, N145J322 K29SP49_57GB47