TECHNICAL DOCUMENTATION

SSP 050 Skoda Superb Automatic Gearbox 01V

PDFEN36 pages2 MB
SSP 050 Skoda Superb Automatic Gearbox 01V - PDF cover

This PDF is currently unavailable.

Read document text
Service ŠkodaSuperbAutomatic Gearbox 01V50Self-Study Programme Not only automatic but manual as well!SP50_10For the first time at Škoda an automatic gearbox with Tiptronic is used - in this case on the ŠkodaSuperb. This transmission shifts gears not only automatically but also makes it possible for the driver to engage the forward gears by operating the selector lever manually. The gearbox design is a planet gear operating with a hydrodynamic torque converter. Cars fitted with an automatic gearbox feature an information display in the dash panel Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted insert as standard equipment. This display provides a range unless authorised by Š KODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilityof different information with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� including the current position of the selector lever or the gear engaged.2GB ContentsIntroduction Overview Specifications Selector Lever Positions Mechanical Components Sectional view of gearbox Hydrodynamic torque converter Torque converter lockup clutch Tow-starting and Towing in Car Power Transmission Forward gears and reverse gear Power Flow ATF ATF Overlapping Overlapping shift System Overview Gearbox Control Automatic gearbox control unit J217 Self-diagnosis Emergency mode Sensors Protected by copyright. for sender private or commercial Gearbox input Copying speed G182purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Gearbox output speed sender G195 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� ATF temperature sender G93 Tiptronic switch F189 Starter lockout relay J207 Actuators Solenoid valves N88 to N90 and Pressure control valves N215 to N218 Further function components Function Diagram 4 4 5 6 8 8 10 13 14 15 15 18 21 21 22 22 24 26 26 26 26 27 27 28 28 29 29 30 30 32 33Servicexxxxxxxxxxxxxxxx SUPERBServicexxxxxxxxxxxxxxxx SUPERBServicexxxxxxxxxxxxxxxx SUPERBService Servicexxxxxxxxxxxxxxxx SUPERB xxxxxxxxxxxxxxxx SUPERBService Servicexxxxxxxxxxxxxxxx SUPERB xxxxxxxxxxxxxxxx SUPERBS e r v i c eXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXYou can find information regarding inspection and maintenance, setting and repair instructions in the Workshop Manuals.GB3 IntroductionOverviewThe automatic gearbox 01V has been designed for cars with a power output range from 110 up to 150 kW. The gearbox is also positioned lengthwise in the direction of travel to match the installation position of the engine. The mechanical components of the automatic gearbox operate on the principle of a planetary gear. The gearbox control is electro-hydraulic. In this case, the electric control is assured by the automatic gearbox control unit J217 installed in the car. The hydraulic control is performed by the hydraulic shift control unit (shift valve body) which is bolted to the bottom of the gearbox housing and is surrounded by the oil pan.Brake GATF breather Brake D Ravigneaux planet gear setGearbox housing Clutch F Rear-mounted planet gear setParklock gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Spur gearEnd coverDrive pinionOil panFreewheel/gearboxClutch E4GB SpecificationsAutomatic gearbox Transmission capability max. torque max. output Weight Capacities ATF in planet gear Axle oil in final drive Gearbox code Engine assignment EZY 2.8-ltr./142 kW petrol engine 01V 310 Nm 150 kW 110 kg (with ATF* and axle oil) 9.0 ltr. 0.75 ltr. FNL 2.5-ltr./114 kW diesel engine*ATF = Automatic Transmission FluidClutch A Clutch BBrake CTorque converterATF pumpDifferentialFinal drive coverProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Flange shaft unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�for rightdrive shaftSP50_30Oil filler plug for final gear (inspection plug)GB5 Selector Lever PositionsPR N D 4 3 2Selector lever in left selector gateIn contrast to the automatic gearboxes 01M and 001 (JATCO) which have been fitted so far to Škoda models, the selector lever of the automatic gearbox 01V has two selector gates.Selector lever in right selector gateSP50_24Selector lever in left selector gate In this selector gate it is possible to engage positions P, R, N, D, 4, 3 and 2. First gear cannot be selected by the driver. It is engaged by the automatic gearbox control unit J217 depending on the vehicle load. In this case the DSP (Dynamic Shift Programme) is active in the left selector gate.4 32P RNDSP50_09Please refer to Self Study Programme 40 for further information regarding the selector lever positions P, R, N, D, 4, 3 and 2 as well as the DSP.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The position of the selector lever is indicated in the lower half of the large information display in the dash panel insert.SP50_226GB Selector lever in right selector gate The selector lever can be moved in position D into the right gate, the Tiptronic gate. When this is done, the gear engaged at that moment is maintained.P RND4 32If the selector lever is moved forward or back within this Tiptronic gate, the gearbox shifts up or down one gear each time. –SP50_08–One-touch in „+“ direction; gearbox shifts up one gear One-touch in „–“direction; gearbox shifts down one gearThe individual gears are safeguarded in terms of engine revs by the automatic gearbox control unit J217 (in software side). If the Protected by copyright. Copying for private or commercial purposes, in part orselector in whole, is notlever permittedis not moved within the unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Tiptronic gate, the automatic gearbox for with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� safety reasons automatically shifts into the next higher gear (just before maximum engine speed is reached). In the same way, the automatic gearbox shifts down if the engine revs drop. This is also done automatically, it is not necessary to operate the selector lever. On the other hand, it is not possible to perform compulsory shifts using the Tiptronic beyond the permissible shift speed ranges.The already familiar kickdown function is also available when the selector lever is in the right-hand selector gate.The gear engaged shows an information display of the dash panel insert.SP50_23GB7 Mechanical ComponentsSectional view of gearboxBrake C Clutch B Clutch E Clutch AGearbox housingPump wheel of torque converterTurbine of torque converterProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Gearbox input shaftTorque converter housingTorque converter lockup clutchControl valve bodyATF drain plug8GB Ravigneaux planet gear setBrake DBrake GSpur gearDrive pinionParklock gearClutch FProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Rear-mounted planet gear setATF filler plugSP50_21Oil filterOil panGB9 Mechanical ComponentsHydrodynamic torque converterThe task of the torque converter is to absorb the engine torque and to transmit it to the planetary gear. When this is done, the mechanical energy of the engine is converted into dynamic energy of the ATF. After this, the energy is again converted into mechanical energy which drives the planetary gear. The torque converter is also required as a hydraulic start-off clutch and for boosting the engine torque. The torque converter is filled with ATF which is kept in constant circulation by the ATF pump.SP50_04Torque converterEnclosed within the housing of the torque converter are – – – – the pump wheel the turbine wheel the impeller and the torque converter lockup clutch (refer to description on p. 13).Engine crankshaftTorque converter lockup clutchPlanetary gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP50_43Turbine wheelImpellerPump wheel10GB Pump wheelThe pump wheel It is connected to the drive of the engine. It rotates at engine speed and circulates the ATF.SP50_44Planetary gearThe turbine wheel The turbine wheel is positioned opposite the pump wheel. It absorbs the torque of the engine by means of the ATF and transmits it through the gearbox input shaft to the planetary gear.SP50_45Turbine wheelGearbox input shaftProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The impeller The impeller is positioned between the pump wheel and the turbine wheel. It deflects the ATF back to the pump wheel.SP50_46ImpellerGB11 Mechanical ComponentsOperating principle of the torque converter and of the torque conversion The torque converter is able to operate in two ranges: – with torque increase – without torque conversion as a hydrodynamic clutch4 5 6Turbine wheel Pump wheel3 2Impeller1FreewheelNote: The inlet and outlet areas of the gears are identified in the illustration with 1 to 6 .Gearbox input shaftSP50_39Tor que increaseHy d r o d y n a mi c c l u tc h o p e r a ti o nThe ATF is accelerated from 1 to 2 and, in so If the conversion of the rotational speed is doing, absorbs energy. This energy-laden ATF greater as a result of the external operating flow passes to the turbine wheel inlet 3 . At it conditions, in other words the difference in flows through the turbine wheel in the the rotational speed between pump wheel and direction 4 the ATF partially dissipates the turbine wheel is less, the direction of flow of Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted acquired energy to the wheel. the impeller is altered in such a way as to unless authorised by ŠKODA AUTO A. S.turbine ŠKODA AUTO A. S. does This not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� energy conversion provides the turbine wheel reverse the direction of torque of the impeller. torque and thus the gearbox input torque. As it flows from 5 to 6 the ATF flow is once What this means is that a turbine torque is again deflected in the impeller which results in produced which in comparison to the pump the impeller torque which is supported by torque is now less in conformity with means of a freewheel at the gearbox housing. MT = MP – ML. The torque boost no longer For the range of small rotational speed exists. In order to prevent this, a freewheel is conversions (in other words the difference in positioned between the impeller and its the rotational speed between pump wheel and connection to the gearbox housing. This turbine wheel is relatively large), the permits the torque to be transmitted to the directions for the torques at the pump wheel impeller support only in one direction. What and at the impeller are identical, which in turn this means is that the impeller torque is now results in MT = MP + ML. reduced to zero, in other words ML = 0. When MT = MP + 0 exists, the torque converter MT = Turbine wheel torque is transformed into a hydrodynamic clutch. MP = Pump wheel torque ML = Impeller torque The torque increase is all the greater, the greater the difference in rotational speed (slip) between pump and turbine wheel.Note: Please refer to Self Study Programme 20 for further information on the hydrodynamic torque converter.12GB Torque converter housing Friction liningTorque converter lockup clutchThe torque converter becomes less economic as the rotational speed increases. At high rotational speeds it transits only up to 85 % of the engine torque. A torque converter lockup clutch is integrated in the housing of the torque converter in order to ensure that the entire engine torque is transmitted. When this lockup clutch is closed, it transmits the engine torque mechanically to the gearbox input shaft. The lockup clutch is connected by means of a spline to the gearbox input shaft. It has a ringshaped friction lining on the side facing the engine. When the torque converter lockup clutch is closed, the friction lining presses against the torque converter housing which is bolted to the driven plate of the engine.SP50_49Torque converter lockup clutchTorque converter housingLockup clutchFriction lining ATFN218Lockup clutch openedProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�J217The ATF in the torque converter is constantly circulating. When the lockup clutch is open, it flows along the front of the lockup clutch and from there into the torque converter. The pressure on both sides of the clutch is balanced.SP50_48Lockup clutch closed In order to close the lockup clutch, the direction of flow of the ATF is reversed by the automatic gearbox control unit J217 and by the pressure control valve N218. When this is done, air is released from the space upstream of the clutch and the ATF flows to the rear. The clutch closes as a result of the pressure difference.N218J217SP50_47GB13 Tow-starting and Towing in CarTow-starting the car On a car fitted with an automatic gearbox it is not possible to start the engine by pushing or tow-starting the car. The control pressure required for shifting a gear is produced by the ATF pump only when the engine is running. In other words, for technical reasons, it is not possible to transmit the propulsive energy of the car to the engine.SP50_05Towing in the car It is possible to tow in a car fitted with an automatic gearbox. In this case, shift the selector lever into position N. When towing in the car do not exceed a speed of 50 km/h. The towing distance must also not be greater than 50 km. If it is necessary to tow the car a greater distance, the front wheels of the car must be raised clear of the ground. The reason for raising the car at front is that lubrication of the rotating gearbox parts is not adequate when the engine is not running. For the same reason, it is not possible to tow the car with the rear wheels raised. If the rear of the car is raised, the drive shafts Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO reverse A. S. does not direction. guarantee or accept any liability rotate in the with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� If a car is towed in this way (reverse) the gears in the automatic gearbox reach such high speeds that the gearbox may suffer severe damage within a short time.SP50_0614GB Power TransmissionForward gears and reverse gearThe 5 forward gears and reverse gear are shifted by the combination of a Ravigneaux planet gear set and a rear-mounted single planet gear set.Note: In comparison: The automatic 4-speed gearboxes 01M and 001 (JATCO) had only the Ravigneaux planet gear set.SP50_50Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Ravigneaux planet gear setLarge sun gear Small planet gearRear-mounted planetary gear setAnnulus gearLarge planet gearSun gear Small sun gearSP50_51Planet gearSP50_52Annulus gear1 planet carrier with 3 large and 3 small planet gears1 planet carrier with 3 planet gearsGB15 Power TransmissionOverview of clutches, brakes and planet gear setsA C B EGearbox input shaftRavigneaux planet gear set Clutch A Clutch B Clutch E Brake C drives large sun wheel drives small sun wheel drives planet carrier holds small sun wheelProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Brake D (freewheel D) holds planet carrier with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�16GB Large planet gearDAnnulus gear Small planet gearG FPlanet gearOutputPlanet carrier Sun gear Small sun gear Large sun gear Rear-mounted planet gear set Ravigneaux planet gear set180180-SP50_01Rear-mounted planet gear set Clutch F Brake GProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�drives sun wheel holds sun wheelThe annulus gear is at the same time always the output of the Ravigneaux planet gear set and the input of the rear-mounted planet gear set.The output of the gearbox is performed by the planet carrier of the rear-mounted planet gear set.GB17 Power Flow1st gearAAnnulus gearDGPlanet carrier OutputGearbox input shaftSP50_02Small sun gearLarge sun gearSun gearClutch A Freewheel below brake D– drives the large sun wheel – blocks and holds the planet carrier • the large sun gear drives the planet carrier • the planet gears drive the annulus gear • the annulus gear drives the rear-mounted annulus gearBrake G– holds the sun gear in the rearmounted planet gear set • the annulus gear drives the rear-mounted planet carrier • output2nd gearA CAnnulus gearGOutputPlanet carrierSP50_03Gearbox input shaftSmall sun gearLarge sun gearSun gearClutch ABrake CBrake G – holds the sun gear in the rear– drives the large sun gear mounted planet gear set • the large sun gear drives the • the rear-mounted annulus planet gears Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTOgear A. S. does not guarantee accept any gears liability drives theorplanet with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� • the planet gears orbit around – holds the small sun gear the sun gear • the planet gears orbit • output around the small sun gear • the planet gears drive the annulus gear • the annulus gear drives the rear-mounted annulus gear18GB 3rd gearA CAnnulus gear Planet carrierFOutputSP50_11Gearbox input shaftSmall sun gear Large sun gearSun gearUp to the Ravigneaux planet gear set as in 2nd gear – the annulus gear drives the rear-mounted annulus gear Clutch F – drives the sun gear in the rearmounted planet gear set • planet carrier in block mode Note: Block mode: sun gear, planet carrier and annulus gear rotate together at the same speed. the ratio is thus 1:1.4th gearAAnnulus gearFEPlanet carrierOutputSP50_12Gearbox input shaftSmall sun gearLarge sun gearSun gearClutch A + E– drive the planet carriers and the large sun wheel • block mode • the annulus gear is driven at the input speedIn the rear-mounted planet gear set as in 3rd gear (block move).Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB19 Power Flow5the gearC EAnnulus gear Planet carrierFOutputSP50_13Gearbox input shaftSmall sun gearLarge sun gearSun gearClutch E Brake C– drives the planet carrier – blocks the small sun gear • planet gears orbit around the small sun gear and drive the annulus gear • the annulus gear drives the rear-mounted annulus gear. The rear-mounted planet gear set operates in the block mode as in 3rd and 4th gearReverse gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Annulus unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO gear A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�BDGPlanet carrierOutputSP50_14Gearbox input shaftSmall sun gearLarge sun gearSun gearClutch B Brake D– drives the small sun gear – holds the planet carrier • the small sun gear drives the planets in a different direction • the planets drive the annulus gear in the opposite direction • the annulus gear drives the rear-mounted annulus gearBrake G– holds the sun gear in the rearmounted planet gear set • the annulus gear drives the planets • the planet gears orbit around the sun gear • output20GB ATFATFThe automatic gearbox 01V is filled with a special oil, the so-called ATF (Automatic Transmission Fluid). This special oil performs the following functions: – Cooling the hydrodynamic torque converter – Lubricating and cooling the mechanical gearbox components (shift elements, gearwheels, bearings) – Supplying the pressure for the hydraulic control – Supplying the pressure for operating the shift elements ATF consists of a base oil on a mineral oil basis to which are added additives (chemical substances). As a result of these additives, the ATF satisfies the wide range of requirements in an automatic gearbox: – Temperature resistance from –40 oC up to +150 oC – Resistance to thermal ageing – Lowest possible viscosity change over temperature – High static friction coefficient and increasing friction curve as slip speed rises – Prevention of foaming – Avoidance of deposits – Avoidance of corrosionATF cooler The ATF cooler is integrated in the coolant radiator.ATFATF coolerEngineAutomatic gearboxProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP50_31Coolant radiatorCoolantGB21 OverlappingOverlapping shift(shift without interruption to traction) Automatic gearboxes differ from manually shifted gearboxes essentially in terms of three aspects: 1. Starting off is performed without any operation of the clutch. 2. The gearshift is performed as a power shift without any interruption to traction. 3. The gear changes are performed automatically. Starting off without operation of clutch A hydrodynamic torque converter is used as a starting-off element in an automatic gearbox. The minimal transmission capability of the torque converter when the engine is running at idle speed necessitates only slight braking forces in order to bring the vehicle to a stop and hold it. When the brake is opened, the vehicle creeps. This makes it possible to perform very responsive manoeuvring and parking. Shifting without interruption to traction On a manually shifted gearbox the clutch between the engine and the gearbox is opened in order to shift gears. When this is done, the tractive force is interrupted and vehicle acceleration is reduced practically to zero. In contrast to this, a gear change in an automatic gearbox is performed as a power shift without any interruption to traction. This necessitates several shift elements (clutches and brakes) which are dimensioned in such a way as to be able to transmit the engine power and to shift. Shifting without any interruption to the tractive force is also known as overlap shift. The task of the overlap shift is to produce soft shift transitions between the gears. The overlap shift can be presented as follows in a simplified manner:During the gearshift the torque is split between the clutches.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The pressure at the clutch which is to be engaged, increases. At the same time the pressure at the clutch which is disengaged, decreases.The engaged clutch slowly absorbs the entire torque.SP50_2522GB In order to describe the sequence of the overlap shift in greater detail, it is necessary to look at the time relation of a number of influencing factors.Shift phaseFillingOverlapIncreaseEngagementLegendOutput torqueClutch torque/output torqueTorque of disengaging clutchEngine speedEngine speedTorque of engaging clutchTime SP50_29Torque and engine speed curves of a power upshiftThe illustration shows the torques at the two clutches (disengaging clutch and engaging clutch), the output torque of the gearbox and the engine speed curve for a power upshift. During the overlap phase the torque transmitted by the disengaging clutch drops and at the same time the torque transmitting by the engaging clutch is increased. At the end of the overlap phase the engaging clutch transmits the torque of the new gear while the speed of the old gear still exists. As a result of a further increase in the torque at the engaging clutch, the rotating masses within the engine are synchronised to the speed level of the new gear (increase phase).The output torque plotted in the graph shows that, during the upshift, the torque drops during the overlap phase to the level of the new gear. In the increase phase the output torque rises for a short time as a result of the energy from the engine rotating masses being introduced into the drive train. Once the synchromesh speed is reached, the level of the output speed and the torque of the new gear are again reached. Automatic gear change In an automatic gearbox the gears are changed not by a conscious intervention on the part of the driver but always automatically. This is done by means of a shift programme and is essentially dependent on two influencing variables (vehicle speed and throttle valve position).Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB23 System OverviewSensorsAutomatic gearbox control unit J217 Gearbox input speed sender G182Gearbox output speed sender G195Brake light switch FATF temperature sender G93 K wire Diagnostic connectionProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Tiptronic switch F189Multifunction switch F125Bulb for left, right reversing light M16, M17 24Starter lockout relay J207GB ActuatorsDrive train CANDash panel insert KSelector lever position display Y6Engine control unit J... • Engine speed • Fuel consumption • Throttle valve position • Selector lever position • Vehicle speed • Coolant temperatureProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Solenoid valves N88 to N90 Pressure control valves N215 to N218Selector lever position P/N warning lamp K142ABS control unit J104 • TCS or ESP controlDrive train CANSelector lever lock solenoid N110SP50_07GB25 Gearbox ControlAutomatic gearbox control unit J217The automatic gearbox control unit J217 controls the output signals and thus the actuators on the basis of the input information supplied by the sensors. The control unit J217 is located ahead of the front passenger seat below the carpeting in the footwell.SP50_37Self-diagnosisThe control unit J217 automatically monitors the signals of the sensors as well as the operation of the actuators and conducts a selfProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted test of the control unit. If faults occur, these are unless authorised by ŠKODA AUTO A. S. Š KODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� stored in the fault memory of the control unit J217. Please use the up-to-date workshop literature and the vehicle diagnosis, testing and information system VAS 5051 for fault finding and for reading out the fault memory.SP50_41Emergency modeThe gearbox control is designed in such a way that, if an input signal is not received, it switches to a substitute signal. In the event of the failure of an essential signal, an actuator or of control unit J217 itself and it is not possible to form a substitute signal, the gearbox switches into the emergency mode. This is indicated by all of the segments of the selector lever position display Y6 in the dash panel insert K lighting up or going blank. The emergency mode of the gearbox means: – All the solenoid valves and pressure control valves are de-energized, and are pushed into an off position by springs. It is now only possible to drive forward in 4th gear. Reverse gear can be engaged. The hydraulic system operates at maximum pressure. The torque converter lockup clutch is no longer closed. The Tiptronic mode is not possible.– – – –26GB SensorsGearbox input speed sender G182Gearbox housingThe gearbox input speed sender G182 is attached to the gearbox housing above the control valve body. It detects the input speed of the gearbox. The signal of the gearbox input speed is required in order to achieve gentle control of the shift transitions between the gears. If this signal is not received, the gearbox operates in the emergency mode (refer to p. 26).Gearbox input speed sender G182Control valve bodySP50_32Housing of clutch BRavigneaux planet gear setA C B D180-G 180FOutputGearbox input shaftSP50_33Housing of clutch AG182Planet gear carrierIn order to achieve smooth gearshift quality in In order to be able to determine the gearbox all gears (precise control of the shift input speed with sender G182, it is necessary operations) it is essential to exactly determine to tap the housing of clutch A which theProtected gearbox input speed. introduces by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedthe force. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability The housing of clutch A is positively with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� The system for determining the gearbox input connected to the gearbox input shaft and is speed consists of a gearbox input speed located within the housing of clutch B. sender G182 (Hall sender) and a magnetic This housing is manufactured from a nonring. magnetizable material in order to ensure that The magnetic ring is connected to the housing the magnetic fields of the magnetic ring are of clutch A. not shielded by the housing of clutch B.GB27 SensorsGearbox output speed sender G195Gearbox housingThe gearbox output speed sender G195 is located at the rear right of the gearbox housing, as illustrated, and detects the gearbox output speed. It is an inductive sensor. The automatic gearbox control unit J217 uses the gearbox output speed to calculate the vehicle speed. The information regarding the vehicle speed is required for – the decision of which gear should be engaged, – controlling the shift pressure for the shift transitions. If this signal is not received, the gearbox operates in the emergency mode (refer to p. 26). If the sender is replaced, it is not necessary to remove the control valve body.Gearbox output speed sender G195SP50_34Control valve bodyATFWiring loomATF temperature sender G93The ATF temperature sender G93 monitors the temperature of the ATF. It is integrated within the wiring loom at the control valve body and is surrounded by apurposes, constant flow of ATF. If a Protected by copyright. Copying for private or commercial in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability fault of occurs, itthis cannot replaced with respect to the correctness information in document.be Copyright by ŠKODA separately AUTO A. S.� but only in combination with the wiring loom. The sender is a PTC (Positive Temperature Coefficient) resistor, in other words its resistance increases as the temperature rises.SP50_35ATF temperature sender G93If no signal is received from the ATF oil temperature sender, the coolant temperature of the engine is used as a substitute.28GB Tiptronic switch F189Selector lever cover with Tiptronic switch F189The Tiptronic switch F189 is integrated in the printed circuit plate of the symbol insert which is located in the selector lever cover. The switch consists of a total of 3 Hall sensors which are actuated individually by the Tiptronic movement by means of the ferromagnetic material. As a result of the signals from the Tiptronic switch F189 the gears are shifted after onetouch of the selector lever – forward (+) up one gear, – back (–) down one gear. If the signal is not received, no Tiptronic operation is possible.Cover stripSP50_40Ferromagnetic materialHall sensor for Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Tiptronic recognition with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Hall sensor for downshifts Hall sensor for upshiftsSP50_42Selector lever coverNote: When carrying out service work please take care when removing and installing the selector lever cover and ensure the ferromagnetic material is firmly fixed in place. If this is not the case, this can result in malfunctions of the Tiptronic shift. Refer also to the Workshop Manual.Additional relay holder (13 relays)Starter lockout relay J207This relay is installed in the additional relay holder (13 relays) above the relay carrier behind the dash panel trim on the driver side. It is operated by the multifunction switch F125 and prevents the engine from being started if a drive position is engaged (selector lever position R, D, 4, 3, 2 and Tiptronic gate).SP50_32Relay carrierStarter lockout relay J207GB29 ActuatorsSolenoid valves N88 to N90 and pressure control valves N215 to N218Solenoid valves N88 to N90 and pressure control valves N215 to N218 are housed within the control valve body. The control valve body is located in the oil pan of the gearbox.SP50_38N215 N90Control valve bodyN89 N217 N218 N216 N88The valves are operated by the automatic gearbox control unit J217 for shifting the gears. In this case, they translate the electric signals into hydraulic pressures. The pressure produced by the ATF pump and controlled by the pressure control and solenoid valves then operates the clutches and brakes in the automatic gearbox.Note: Also integrated in the control valve body are: • hydraulic valves • oil galleries Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted • A. selector slideorfor positions R, unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO S. does not guarantee accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� D, 4, 3 and 2Solenoid valves N88 to N90 The solenoid valves are Yes/No valves. They are either open or closed, in the same way as a light switch which is only able to adopt the states of „on“ and „off“. The solenoid valves open or close on the basis of the signals supplied by the control unit J217 and cause the hydraulic valves to direct the system pressure along the oil galleries to the clutches or brakes. They are closed in the de-energized state.SP50_2630GB Pressure control valves N215 to N218 The pressure control valves N215 to N218 are able to steplessly adopt all the states between „open“ and „closed“. Consequently, the oil pressure is steplessly controlled, in the same way to a volume control which is able to recognize all the states between „high“ and „low“. The opening of the valves is directly related to the value of the electrical control current which is transmitted as a signal by the automatic gearbox control unit J217. In the non-actuated state the pressure control valves are open and are closed as the control current increases.Hysteresis for increasing pressure characteristic0,5 0,4ATF pressure [MPa]Tolerance range for decreasing pressure0,3 0,2 0,1 0 0 0,2 0,4 0,6 0,8SP50_28SP50_27Control current [A]Tasks of the pressure control valves:Effects of failure of solenoid valves N88 to N90 and of pressure control valves N215 to N218N215 Protected by copyright. Copying for private or commercial purposes, part or in whole, is not permitted In thein event of an open circuit in the wiring or It controls the entire pressure line with unlessATF authorised by ŠKODAin AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability short circuit to earth to with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�the pressure control the driving conditions for the operation of the valve N218, the torque converter lockup clutch complete gearbox. In so doing, it ensures is no longer closed. It is still possible to shift smooth driving and jerk-free gearshifts.gears. In the event of a failure of solenoid valves N88 to N90 and of pressure control valves N215 to N217 and also in the case of a short circuit to positive at N218, the gearbox operates in the emergency mode (refer to p. 26).N216 and N217 These valves control the ATF pressure during gearshift operations by means of hydraulic valves in order to gently open and close the clutches and brakes.N218 The pressure control valve N218 controls the pressure when the torque converter lockup clutch opens and closes.GB31 ActuatorsFurther function componentsNote: Familiar function components which have already been described in detail in previous Self Study Programmes, are used for controlling the automatic gearbox 01V. The table refers to the relevant Self Study Programmes. Please make use of this detailed information.Function componentFunction description SSP 40 (shows different shape, installation position and function identical) SSP 40Brake light switch F The automatic gearbox control unit J217 is supplied with the information „Brake operated“ via this switch.SP50_15Selector lever position P/N warning lamp K142 It lights up when the ignition is switched on if the selector lever is in position P or N. It is designed to draw the driver's attention to the fact that the brake has to be depressed for shifting the selector lever out of these two positions.andProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP50_16Selector lever lock solenoid N110 After the ignition is switched on, it is activated and prevents a driving position being unintentionally engaged from selector lever position P or N so long as the brake is not depressed.Multifunction switch F125 It detects the position of the selector lever and signals this to the automatic gearbox control unit J217.SP50_17SSP 40 (shows different shape and installation position, function identical)32GB Function DiagramLegend of function diagram (on pp. 34 and 35) Components B/50 CAN-A CAN-K D/50 E20 F F125 F189 G93 G182 G195 J... J207 J217 J285 J533 K K142 L101 M16 M17 N88 N89 N90 N110 N215 N216 N217 N218 S Y6 Colour codingStarter/terminal 50 = Input signal Drive train CAN Convenience CAN = Output signal Ignition-starter switch/terminal 50 Lighting rheostat – switches and = bidirectional instruments Brake light switch = Positive Multifunction switch Tiptronic switch = Earth ATF temperature sender Gearbox input speed sender = CAN databus Gearbox output speed sender Engine control unit = Diagnostic Starter lockout relay Automatic gearbox control unit Control unit with display unit in dash panel insert Databus diagnostic interface Dash panel insert Selector lever position P/N warning lamp Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Selector lever scale lighting with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Bulb for left reversing light Bulb for right reversing light Solenoid valve 1 Solenoid valve 2 Solenoid valve 3 Selector lever lock solenoid Pressure control valve -1- for automatic gearbox Pressure control valve -2- for automatic gearbox Pressure control valve -3- for The function diagram represents a simplified automatic gearbox current flow diagram. Pressure control valve -4- for automatic gearbox It provides information on the connections of Fuse all the system components of the gearbox Selector lever position display control.GB33 Function Diagram30 15B/50S 10A J207S 15AG195D/505455261514 J21742368379628345253Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� M16, M17F12531Refer to p. 33 for the legend of the Function Diagram.34GB E20 G182 L101 F189 K142N110 J ...F 3116441347Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability by ŠKODA AUTO A. S.� 88 46 with respect to the correctness of information in this 2 document. 10 Copyright3033325129 25421228586CAN -Aυ J533 J285 K N88 N89 N90 N215 N216 N217 N218 G93 Y6inoutCAN -KSP50_18GB35 List of Self-Study Programmes published so farNo. Title1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Mono-Motronic Central Locking Anti-Theft Alarm Working with Current Flow Diagrams ŠKODA FELICIA ŠKODA Vehicle Safety Principles of ABS - Not published ABS FELICIA Immobiliser with Transponder Air Conditioning in Vehicles FELICIA Air Conditioning 1.6-ltr. Engine with MPI 1.9-ltr. Naturally Aspirated Diesel Engine Power-Assisted Steering ŠKODA OCTAVIA 1.9-ltr. TDI Engine OCTAVIA Convenience Electronics System OCTAVIA Manual Gearbox 02K/02J 1.6-ltr./1.8-ltr. Petrol Engines Automatic Gearbox Fundamentals Automatic Gearbox 01M 1.9-ltr. 50 kW SDI/1.9-ltr. 81 kW TDI 1.8-ltr. 110 kW turbo petrol engine 1.8-ltr. 92 kW petrol engine OCTAVIA CAN databus OCTAVIA – CLIMATRONIC OCTAVIA – Vehicle Safety OCTAVIA – 1.4-ltr. Engine and Gearbox 002 OCTAVIA – ESP OCTAVIA – 4 x 4 Petrol Engine 2.0-ltr. 85 kW and 88 kW OCTAVIA – Radio/Navigation System ŠKODA FABIA ŠKODA FABIA – Vehicle Electrics ŠKODA FABIA – Power Steering Petrol Engines 1.4-ltr. - 16 V 55/74 kW ŠKODA FABIA – 1.9-ltr. TDI Unit Injection 5-Speed Manual Gearbox 02T and 002 ŠkodaOctavia – Model 2001 Euro On-Board Diagnosis Automatic Gearbox 001 6-Speed Manual Gearbox 02M ŠkodaFabia – ESP Exhaust Emissions Extended Service Interval 1.2-ltr. 3-Cylinder Petrol Engines ŠkodaSuperb; Presentation of the Vehicle Part I ŠkodaSuperb; Presentation of the Vehicle Part II ŠkodaSuperb; 2.8-ltr./142 kW V6 Petrol Engine ŠkodaSuperb; 2.5-ltr./114 kW TDI V6 Diesel Engine ŠkodaSuperb; Automatic Gearbox 01VProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�No. TitleFor internal use only within the ŠKODA Organisation. All rights reserved. Subject to technical modification. S00.2003.50.20 Technical Status 03/02 GB © ŠKODA AUTO a. s. http://partner.skoda-auto.com❀ This paper has beenmanufactured from chlorine-free bleached cellulose.50