TECHNICAL DOCUMENTATION
SSP 051 2,0l 85 kW Engine with balance shaft transmission

This PDF is currently unavailable.
Read document text
Service51Petrol Engine 2,0 l/85 kWwith balance shaft transmission and 2-stage switching intake manifoldSelf study programmeProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP51_37The engine is already built into ŠkodaOctavia. It is a further development of the previous 2.0-ltr./85 kW Engine. The new operational features are the switching intake manifold and the balance shaft transmission. With this the maximum torque and silent engine running is achieved. You will find further information on the basic engine 2.0-ltr./85 kW in SSP 30.2GBContentsIntroduction Technical highlights of the engine Positions of Components Overview Balance shaft transmission Function and design of the balance shaft transmission Switching intake manifold Power output and torque – general Oscillating pipe charging The switching intake manifold Torque position Power position – long suction path Power position – short suction path Summary Technical modifications Cylinder head cover Conrod Bearing cap for crankshaft Exhaust manifold Oil dipstick Engine management System overview for Bosch Motronic ME 7.5 Sensors Camshaft position sensor – Hall sender G40 Knocking sensor Function diagram 4 4 6 6 8 8 10 10 11 13 14 15 16 17 18 18 18 19 19 19 20 20 22 22 24 25Servicexxxxxxxxxxxxxxxx OCTAVIAServicexxxxxxxxxxxxxxxx OCTAVIAServicexxxxxxxxxxxxxxxx OCTAVIAServicexxxxxxxxxxxxxxxx OCTAVIAServicexxxxxxxxxxxxxxxx OCTAVIAServicexxxxxxxxxxxxxxxx OCTAVIAServicexxxxxxxxxxxxxxxx OCTAVIAS e r v i c eunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability You will find notes on inspection and with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� maintenance, setting and repair instructions in the Workshop Manual.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXGB3IntroductionTechnical highlightsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP51_20Engine mechanics– – – Cross-flow cylinder head Overhead camshaft – OHC Plastic suction pipe with changeable suction paths – – – – Hydraulic bucket tappets Balance shaft transmission Light alloy valve cover Exhaust pipe 4 in 1 for improvement of torque – – – Oil dipstick with plastic shape element New crankshaft bearing cap Secondary air systemEngine management– – – – – Engine management Bosch Motronic ME 7.5 Single-spark ignition system EPC Knock control system with 2 knock sensors Lambda probe upstream of catalytic converter (Wide band probe) – Lambda probe downstream of catalytic converter (Two point probe) – Phase detection by means of Hall sensor at camshaft – 2-stage switching intake manifold4GBEngine code letters Design Displacement Bore Stroke Compression ratio Valve per cylinder Firing order Max. power output Max. torque Engine management FuelAZJ 4-cylinder inline engine 1984 cm3 82.5 mm 92.8 mm 10.5 : 1 2 1-3-4-2 85 kW at 5400 rpm 172 Nm at 1750 … 3200 rpm Bosch Motronic ME 7.5 Unleaded petrol RON 95 (RON 91 is possible with reduction in output)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Emission standardEU4Power output/torque diagram90200The 2.0-ltr engine produces power output of 85 kW (115 HP) at a speed of 5400 rpm. The maximum torque of 172 Nm is available at 1750 … 3200 rpm. Power output and torque are based on operation of the engine with premium unleaded RON 95 petrol.801807016060 P (kW)140 M (Nm)5012040100308020P = Power output M = Torque n = Engine speed0 1000 2000 3000 4000 5000 6000 7000 n (min –1 )SP51_08GB5Positions of ComponentsOverviewMotronic control unit J220 (engine control unit)Valve for variable intake manifold changeover N156Hall sender G40 (camshaft position sensor)Solenoid valve for activated charcoal filter N80Fuel pressure regulatorValve 2 for variable intake manifold changeover N261Knock sensor I G61Knock sensor II G66Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�6GBThrottle valve control unit J338Relay for secondary air pump J299Power supply relay for Motronic J271Air mass meter G70 and intake air temperature sender G42Injection valves cylinder 1 to 4 N30 to N33Coolant temperature sender G62Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted SP51_02 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Secondary air pump motor V101Engine speed sender G28 Ignition coil 1 to 4 with power output stagece N70, N127, N291 and N292GB7Balance shaft transmissionFunction and design of the balance shaft transmissionThe balance shaft transmission shall balance the intervening inertia forces and therefore reduces the oscillations of the drive. With the development of the balance shaft transmission, the following aims have been achieved: – – – – – – The absolute functional safety A silent drive with a low drive torque Placing in existing installation chamber Maintenance-free Cost optimisation through lower modification expendituresns Lower weight increaseSP51_04Balance shaft transmission ChainThe installation of a balance shaft transmission balances the inertia forces 2nd order and the inertia moments of the engine and therefore contributes to a lower noise effect in the interior space. Humming and drumming noises are clearly reduced at a maximum engine speed as of approx. 5000 rpm.The drive of the balance shaft transmission and the oil pump is performed via a chain. This one is driven by the crankshaft. bybalance copyright. Copying for private or commercial purposes, in part or in whole, is not permitted The power transmissionProtected in the shaft unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability transmission is performed via a drive shaft. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Note: Use of the balance shaft transmission causes small torque and power loss. This one is therefore balanced by means of a 2-stage switching intake manifold.Drive shaftOutput shaftChain sprocket on the drive shaftChain sprocket for oil pumpSP51_05Oil pump 8GBPlastic coverRatio 2:1 (velocity)Balance gearChain tensionerSP51_07Oil pumpBalance shaft transmission housingEdge on the balance shaft weightThe two halves of the balance weights are fitted with plastic covers so that the edges of the balance weights on the drive shafts do not foam the engine oil.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted SP51_06 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB9Switching intake manifoldPower output and torque – generalMaximum power output and maximum torque with a low fuel consumption are the highlights of a modern drive for motor vehicles.How does one achieve this aim? The power output P is the product of the engine speed n and the torque M. A maximum power output is obtained either through a higher torque or through a higher engine speed. The many moveable forces of an engine (piston, conrod, crankshaft) set limits to the increase of the engine speed. The torque is still available for power increase. In contrast to technical advantages, most of the motor vehicle tax is calculated according to the displacement, with a determined displacement it is the target point to reach another path, namely to increase the effectiveness of the engine. The principle is to achieve a “higher” torque curve.A maximum torque is obtained through a possible complete combustion of the fuel-air Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted mixture at the right time. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� In order to increase the engine torque, the A determined ratio between air and fuel is displacement can be enlarged or the required for a complete combustion. The compression increased. engine should be optimally supplied with air at each engine speed.Power output/torque diagram of a petrol engineP=M•n [kW] 9550P (kW)M (Nm)P = Power output [kW] M = Torque [Nm] n = Engine speed [rpm]The number factor 9550 results from the conversion of all calculated values, if the numerical values for n in rpm and M in Nm are entered into the equation. P is given in kW.n (min –1 )SP51_2410GBOscillating suction pipe chargingThe suction system takes over the supply of the engine with the necessary combustion air. The pipes which lead the air through to the corresponding cylinders, are designated as oscillating suction pipes, because they function on the principle of the oscillating suction pipe charging.ExhaustAir filterair Throttle valve Fresh airSP51_39The principle of the oscillating suction pipe charging A suction system functions according to the principle of the oscillating suction pipe charging, which means the pressure and vacuum shafts are used for filling the cylinder. For that purpose, we contemplate the processes in the suction pipe. The inlet valve opens. The piston in the cylinder moves downward in direction of the lower dead center (OT). It generates a vacuum shaft in the area of the inlet valve.Oscillating suction pipesCollectorVacuum shaftCollectorThis vacuum shaft extends through the oscillating pipe to the other end and rises into the collector.Oscillating suction pipeSP51_40In the collector, the air volume is kept approximately at ambient pressure. This one is distinctly higher than the air pressure at the inlet valve. The vacuum, which is now created at the end of the pipe carries the here existing air mass with it.Pressure shaftThe air mass which streams into the Collector oscillating suction pipe now generates, Oscillating instead of the vacuum shaft, an equally large suction pipe pressure shaft which spreads to the inlet valve. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability One can also say, that the vacuum shaft is unless with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� SP51_41 eflected at the open end of the pipe in the collector (rebound).GB11Switching intake manifoldThis pressure shaft passes through the oscillating suction pipe and presses the air mass past the open inlet valve into the cylinder. This is performed, until the pressure in front of the inlet valve and the pressure in the cylinder are equally high. A reverse current in the oscillating suction pump is prevented through the closing of the inlet valve.Pressure shaftCollector Oscillating suction pipeSP51_42The distance of the inlet valve from the collector is s. The vacuum or the overpressure shaft requires the time t (in milliseconds) for covering the distance. The vacuum and overpressure shaft always move with the velocity of sound v. This velocity v which does not change, is constant. Because the distance s also does not change, the time t is also constant. The phase in which the inlet valve is open, depends on the engine speed. This means that at an increasing engine speed, the phase in which air at the opened inlet valve can flow into the cylinder will always be shorter. At higher engine speeds, the incoming pressure shaft would therefore meet the already closed inlet valve.Vacuum shaft Pressure shaftsSP51_43t =s vs = Oscillating suction pipe length t = Time v = Sound velocityIn order to shorten the time t, so that the pressure shaft can still meet an open inlet Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted valve at higher engine speeds, it is necessary unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the s correctness of information in this document. Copyright by ŠKODA AUTO A. S.� to shorten the distance (oscillating suction pipe length). The rapidity of the shaft movement cannot be Note: changed. The higher the speed, the shorter the suction pipe length. The technical solution for shortening the oscillating suction pipe length would be a A long pipe (torque stage) is switchable suction pipe. suitable for lower to medium engine speeds. A short pipe (torque stage) is suitable for high engine speeds.12GBThe switching intake manifoldThe character of an engine determines considerably its power output and its torque. The filling ratio of the cylinder and the geometrical shape of the suction system has an important influence on it. A different geometry of the suction pipes is required for a maximum torque than for a high power output. A compromise constitutes a medium suction pipe length with a medium cross section. An optimal choice is a switchable intake manifold.Collector 1 Collector 2Vacuum box for switching intake manifold flap 1 Vacuum box for switching intake manifold flap 2 Inlet air Outlet airSP51_31The switching manifold flaps are Copyright by ŠKODA AUTO A. S.� with respect to intake the correctness of information in this document. regulated through the electromagnetic valves for the variable intake manifold changeover N156 and N261. The changeover is carried out with the help of the vacuum. The principle Note: of this operation is already known in the The design and function of the Engine 1.6-ltr/74 kW with the code letter AEH. electromagnetic valve for the variable intake manifold The balance shaft transmission leads to a changeover and the operation of power output and torque loss (approx. 1.5 kW the flap with the help of the vacuum or 1 Nm) of the engine. are described in the Self Study The torque and power output losses are Programme 19. eliminated through the balance shaft transmission as well as through the switching intake manifold.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilityGB13Switching intake manifoldTorque positionThe suction channel is available if the switching intake manifold flaps are closed. This means an increase of torque in a speed range from 780 to 4000 rpm.Collector 2 Switching intake manifold flap 2 (closed)Switching intake manifold flap1 (closed)Collector 1Vacuum box for switching intake manifold flap 2Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Vacuum box for unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by intake ŠKODA AUTO A. S.� switchingSP51_09manifold flap 1 Outlet air in the cylinder head Collector rangeInlet air to the throttle valve control unitSuction pathPower output diagram90Torque diagram200801807016060P (kW)14050120401003080M (Nm)The course of the power output and torque curve in the case that both switching intake manifold flaps are closed in the entire speed range.20P = Power output M = Torque n = Engine speed0 1000 2000 3000 4000 5000 6000 7000 0 1000 2000 3000 4000 5000 6000 7000 n (min –1 ) n (min –1 )SP51_17SP51_14In this speed range, the power output and torque are at maximum in comparison with other positions of the switching intake manifold flaps.14GBPower position – long suction pathAt high engine speed, there is less available time to fill the cylinder. The suction path should be shorter. The switching intake manifold 1 opens at 4000 rpm.Collector 2 Switching intake manifold flap 2 (closed)Switching intake manifold flap 1 (closed)Collector 1Vacuum box for switching intake manifold 2Vacuum box for switching intake manifold 1 Outlet valve in the cylinder head Collector rangeSP51_10Inlet valve to the throttle valve control unitSuction pathPower output diagram90Torque diagram200801807016060P (kW)140501204010030Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 80 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability = Power with respect to the correctness of information in this document. Copyright P by ŠKODA AUTO A. output S.�M (Nm)The course of the power output and torque curve in the case that the switching intake manifold flap 1 is open and the switching intake manifold 2 is closed in the entire speed range.20M = Torque n = Engine speed0 1000 2000 3000 4000 5000 6000 7000 0 1000 2000 3000 4000 5000 6000 7000 n (min –1 ) n (min –1 )SP51_18SP51_15In this speed range, the power output and torque are at maximum in comparison with other positions of the switching intake manifold flaps.GB15Switching intake manifoldPower position – short suction pathThe 2nd switching intake manifold flap opens at 4800 rpm.Switching intake manifold flap 2 (closed)Collector 2Switching intake manifold flap 1 (closed)Collector 1Vacuum box for switching intake manifold flap 2Vacuum box for switching intake manifold flap 1 Outlet air in the cylinder head Collector rangeSP51_11Inlet air to the throttle valve control unitSuction pathPower output diagram90Torque diagram The course of the power output and torque curve in 180 the case that both switching Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability intake manifold flaps are 160 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� closed in the speed range.200 140 120807060P (kW)50401003080M (Nm)20P = Power output M = Torque n = Engine speed0 1000 2000 3000 4000 5000 6000 7000 0 1000 2000 3000 4000 5000 6000 7000 n (min –1 ) n (min –1 )SP51_19SP51_16In this speed range, the power output and torque are at maximum in comparison with other positions of the switching intake manifold flaps.16GBSummaryWhen reaching a determined engine speed through the successive following opening of the switching intake manifold flaps, it is possible for each speed to always reach the maximum power output and the maximum torque in the entire range of the engine speed.Power output diagram The switching intake manifold flaps remain in each position only as long as the power output and torque are at maximum at the corresponding speed. A power output diagram with an optimal course of the power output curve is created through the connection of three selected (illustrated in different colours) engine speed ranges.90909090808080807070707060P (kW)P (kW)P (kW)505050P (kW)+60+60=605040404040303030302020202001000200030004000500060007000010002000n (min –1 )SP51_17Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 3000 4000 authorised 5000 6000 7000 1000 A. 2000 3000 4000 AUTO 5000 6000 7000 0 1000 2000 3000 4000 6000 unless by ŠKODA 0AUTO S. Š KODA A. S. does not guarantee or accept any5000 liability n (min ) n (min ) (min ) with respect to the correctness of information in this document. Copyright by ŠKODA n AUTO A. S.�–1 –1 –17000SP51_18SP51_19SP51_13Torque diagram The switching intake manifold flaps remain in each position only as long as the power output and torque are at maximum at the corresponding speed. A torque diagram with an optimal course of the torque curve is created through the connection of three selected (illustrated in different colours) engine speed ranges.200200200200180180180180160160160160140120+140120+140120=140M (Nm)M (Nm)M (Nm)1201001001001008080808001000200030004000500060007000010002000300040005000600070000100020003000400050006000700001000200030004000500060007000n (min –1 )n (min –1 )n (min –1 )n (min –1 )SP51_14SP51_15SP51_16SP51_12GB17M (Nm)Technical modificationsCylinder head coverVersion for engines with the code letters AEG, APK, AQY and AZHPlastic fitting for crankcase ventilationVersion for engines with the code letters AZJGasketSP51_29SP51_28On these engines, the cylinder head cover is made out of sheet metal. The plastic fitting for the crankcase ventilation is mounted on it. A gasket is located between the cylinder head cover and the plastic fitting.On these engines, the cylinder head cover is made out of aluminium. The crankcase ventilation is integrated in it. Therefore the gasket is not needed. The aluminium cylinder head cover is less expensive than the sheet metal cylinder head cover with additional plastic fittings.Trapezoidal shape conrod eyeConrod– Conrod eye narrower than conrod foot (piston is fitted onto the narrow conrod eye) – Milling of the conrod eye (trapezoidal shape) – Piston bolts reduced in diameter from 20 mm to 19 mm – Bearing shells without side catches An improvement of the engine acoustics and friction ratios is achieved through modifications at the crank drive.Bearing shellsConrod footProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP51_3018GBBearing cap for crankshaftThe bearing caps have small screw holes. The play between the bearing cap bolt and the bearing cap hole is minimized. The bearing cap 1 is narrower in comparison with the other bearing caps. This means a distance from the end face of the cylinder block to the bearing cap 1 is reached. The distance amounts to 0.5 mm. It is necessary, so that the chain tensioner of the balance shaft transmission does not sit close to the bearing cap 1. The chain sprocket on the crankshaft drives a chain. The drive shaft of the balance shaft transmission and the oil pump is driven by the chainChain sprocket on the crankshaftSP51_33Bearing cap bolt Bearing cap 10,5Cylinder blockExhaust manifoldThe single gas pipes of the cylinders are lead together into one pipe (one branch). With the version of the exhaust manifold for the engines with the code letters AEG, APK, AQY and AZH, the exhaust pipes of the cylinders end in 2 pipes (2-branch). The one-branch version of the exhaust system improves the torque.SP51_35Oil dipstickThe oil dipstick has at its end a plastic shape element and hence does not strike the balance shaft transmission. The flat oil dipstick would remain hanging at the balance shaft transmission and falsify the measuring result.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability element with respect to the correctness of information in this document. CopyrightPlastic by ŠKODAshape AUTO A. S. �SP51_34GB19Engine ManagementA system overview for Bosch Motronic ME 7.5SensorsEngine speed sender G28 Motronic control unit J220 (engine control unit)Hall sender G40 (camshaft position sensor) Air mass meter G70 and intake air temperature sender G42Throttle valve control unit J338 with angle sender -1- and -2- for throttle valve drive (EPC) G187 and G188Accelerator pedal position sender G79 and accelerator pedal position sender G185Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�CAN drive Clutch pedal switch F36Coolant temperature sender G62Knock sensor I G61Knock sensor II G66 Brake light switch F and brake pedal switch F47 Oil level/oil temperature sender G266Lambda probe G39 Lambda downstream of catalytic converter G130 Additional signals: • AC compressor “ON“ • AC readiness • Vehicle speed signal • CCS switch E45 with CCS push button (Set) E227 • Alternator terminal DFM 20GBActuatorsFuel pump relay J17 and fuel pump G6Injection valves N30 to N33 Cylinder 1 to 4Ignition coils 1 to 4 with power output stages N70, N127, N291 and N292 W-line Spark plug connector P Spark plug Q Dash panel insert K with databus diagnosis interface J533 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability (Gateway) Active charcoal filter systemwith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�solenoid valve N80Valve for variable intake manifold changeover N156GatewayValve -2- for intake manifold changeover N261EPCExhaust gas warning lamp K83EPC fault lamp K132Throttle valve control unit J338 with throttle valve drive G186K-lineLambda probe heater Z19Brake pad indicator lamp K32Oil pressure indicator lamp K3Lambda probe heater Z29 Relay for secondary air pump J299 and motor for secondary air pump V101 Additional signals: • AC compressor “OFF” • Engine speed signal for Climatronic control unit J255Diagnostic connectionSP51_01GB21SensorsCamshaft position sensor – Hall sender G40The Hall sender G40 is located behind the camshaft sprocket. Its signal determines the camshaft position sensor. It touches a sensor rotor, which is attached to the rear of the camshaft sprocket. In addition, it acts as a quick-start sensor closer description see SSP 30).Sensor rotor Orifice plate of sensor rotorCamshaft sprocketHall senderSP51_23Design and operation In the sensor housing, the permanent magnet and Hall IC* with integrated Hall plate (semiconductor element) are separated by an air gap. The permanent magnet generates a magnetic current (illustrated in Fig as magnetic field lines). If the air gap is free, the magnetic field lines are lead through the guide plate via the air gap into the Hall IC and return via the Hall plate and the air gap into the permanent magnet.Guide plate Sensor housing (nonmagnetic)Magnetic field lines Sensor rotorPermanent magnetHolderAir gapSP51_22Hall plateHall ICThe camshaft position sensor operates according to a principle, which an American Physician Edwin Herbert Hall discovered in the year 1879 and has described as = Hall effect. Hall recognised, that in an electrical conductor (plate) a voltage is generated diagonally to the direction of current, if a magnetic field acts vertically to the upper surface of the conductor. At the same time the moveable electrical charge carriers are deviated to the side.Hall voltage Electric conductor (plate)0VElectric current+SP51_26The emerging voltage is designated as Hall Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Magnet field or lines unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee accept any liability voltage.with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�*)IC = Integrated Circuit22GBIf the orifice plate of the sensor rotor enters into the air gap, the magnetic field lines are detected by it and are directly guided back into the permanent magnet. Therefore the magnetic field lines cannot enter into the Hall IC.Sensor housing (nonmagnetic)Magnetic field lines Orifice plate of the sensor rotor (ferromagnetic)Permanent magnet Air gapHolderSP51_21Hall plateHall ICNo Hall voltageIn this case, no magnetic current occurs through the conductor (plate). The moveable electrical charge carriers are not deviated and therefore no voltage can be generated diagonally to the direction of current.Electrical current0VSP51_25Electrical circuitProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted J220 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�9886108The Hall sender needs a current supply, which is made available by the Motronic control unit J220 – Connections 98 and 108. The Hall sender information is lead from the connection “0” to the control unit connection 86.+°G40SP51_36J220 G40Motronic control unit (engine control unit) Hall senderGB23SensorsKnock sensorThe knock sensors are based on the function principle of the vibration sensors. They are suitable for detection of impact sound vibrations. These type of vibrations occur for example in engines with uncontrolled combustion as “knocks” or “pings”. They are converted by the knock sensor into electrical signals and guided to the engine control unit. This conversion into electrical signals is based on the known piezoelectrical principle similar to the High pressure sender G65 (see SSP 25). At the engine block the occurring impact sound vibrations are detected by a seismic force. For reasons of their inertia, forces of pressure develop in the rhythm of the stimulating vibrations. These forces exert within the piezoceramic ring element a charge transfer. An electric voltage emerges between the ceramic top and bottom side, which is picked off via the contact washers and further treated in the engine control unit.Contact washer Seismic forces HousingFCoolantFastening screwV FProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Piezoceramic ring element Engine block Electrical connectionSP51_32F = Forces of pressure V = VibrationThe observation of the specified tightening torque is the condition for the correct function of the knock sensor.24GBFunction DiagramLegend for Function diagram Components A E45 E227 F F36 F47 G6 G28 G39 G40 G42 G61 G62 G66 G70 G79 G130 Additional signalsBattery 1 Door contact signal CCS switch 2 Brake light signal (terminal 54) CCS push button (Set) 3 CAN drive (Low) Brake light switch 4 CAN drive (High) Clutch pedal switch 5 Alternator terminal DFM CCS brake pedal switch 6 W-line Fuel pump (pre-delivery pump) 7 Vehicle speed signal Engine speed sender 8 Engine speed signal for Lambda probe Climatronic controlunit J255 Hall sender 9 AC readiness Intake air temperature sender 10 AC compressor - on/off Knock sensor I Coolant temperature sender Knock sensor II Air mass meter Accelerator pedal position sender Lambda probe downstream of catalytic converter G185 Accelerator pedal position sender -2G186 Throttle valve drive (EPC) G187 Angle sender -1- for throttle valve drive (EPC) G188 Angle sender -2- for throttle valve drive (EPC) J17 Fuel pump relay J220 Motronic control unit J271 Motronic power supply relay Colour coding/Legend J299 Secondary air pump relay J338 Throttle valve control unit = Input signal N30 Injection valve cylinder 1 N31 Injection valve cylinder 2 = Output signal N32 Injection valve cylinder 3 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO cylinder A. S. ŠKODA AUTO N33 Injection valve 4 A. S. does not guarantee or accept any liability = Voltage supply with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� N70 Ignition coil 1 with power output stage N80 Solenoid valve 1 for activated charcoal = Earth filter system (pulsating) = CAN Bus N127 Ignition coil 2 with power output stage N156 Valve for variable intake manifold = bidirectional changeover N261 Valve 2 for variable intake manifold changeover N291 Ignition coil 3 with power output stage N292 Ignition coil 4 with power output stage P Spark plug connector Q Spark plugs S Fuses V101 Motor for secondary air pump Z19 Lambda probe heater Z29 Heater for Lambda probe 1 downstream of catalytic converterGB25Function diagram31 30 15 J171 S232 10A S229 15A S243 10AS228 15A Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Z19 Copyright G39 N31 of information N32 N33 with respect to N30 the correctness in this document. by ŠKODA Z29 AUTO A. G130 S.�G42 G70 N80S132 50AS131 50Aλλ+A 65 96 89 97 88 3 5 51 70 52 71 63 68 69 26 27 29 53 64117 118 928384 91 33 72 34 36 35 73 1088290869812J338+ MG6 Mo+G186G187G188G185G79G28 G4031Legend for function diagram. See page 25. 26GBS237 20A S234 10A S13 10A S5 7,5AJ299MV101N261FF47F36E45E227J271Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted N156 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�2 9 J220 99 107 106 93 58 60 28 43 54 37 40 41 102 95 103 94 115 56 55 39 38 76 75 57 62 21 121 105345678910N70N127N291N292G66G61G62P Q31inoutSP51_27GB27List of Self Study Programmes so farNo.1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50TitleNo.TitleMono-Motronic 51 Petrol Engine 2.0-ltr./85 kW with balance shaft Central Locking transmission and 2-stage switching intake Anti-theft Alarm manifold Working with Current Flow Diagrams ŠKODA FELICIA ŠKODA Vehicle Safety Principles of ABS – not published ABS FELICIA Immobiliser with Transponder Air Conditioning in Vehicles FELICIA Air Conditioning 1.6-ltr. Engine with MPI 1.9-ltr. Naturally Aspirated Diesel Engine Power-Assisted Steering ŠKODA OCTAVIA 1.9-ltr. TDI Engine OCTAVIA Convenience Electronic System OCTAVIA Manual Gearbox 02K/02J 1.6-ltr./1.8-ltr. Petrol Engines Automatic Gearbox – Fundamentals Automatic Gearbox 01 M 1.9-ltr. 50 kW SDI/1.9-ltr. 81 kW TDI 1.8-ltr. 110kW Turbo Petrol Engine 1.8-ltr. 92 kW Petrol Engine OCTAVIA - CAN Databus OCTAVIA – CLIMATRONIC OCTAVIA – Vehicle safety OCTAVIA – 1.4-ltr. Engine and Gearbox 002 OCTAVIA – ESP OCTAVIA – 4 x 4 Petrol engine 2.0-ltr. 85 kW and 88 kW OCTAVIA – Radio/Navigation system ŠKODA FABIA ŠKODA FABIA – Vehicle Electrics ŠKODA FABIA – Power-Assisted Steering Petrol Engines 1.4-ltr. – 16V 55/74 kW ŠKODA FABIA – 1.9-ltr. TDI Pump nozzle 5-speed Manual Gearbox 02T and 002 ŠkodaOctavia – Model 2001 Euro On Board Diagnosis Automatic Gearbox 001 6-speed Manual Gearbox 02M ŠkodaFabia – ESP Exhaust emission Extended Maintenance Interval 1.2-ltr. 3-cylinder Petrol Engines ŠkodaSuperb; Presentation of the Vehicle Part I ŠkodaSuperb; Presentation of the Vehicle Part II ŠkodaSuperb; 2.8-ltr./142 kW V6 Petrol Engine ŠkodaSuperb; 2.5-ltr./114 kW V6 Diesel Engine Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability ŠkodaSuperb; Automatic Gearbox 01Vwith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Only for internal use in the ŠKODA Organisation. All rights reserved. Subject to technical modifications. GB S00.2003.51.20 Technical status 11/02 © ŠKODA AUTO a. s. http://partner.skoda-auto.com❀This paper has been manufactured from chlorine-free bleached cellulose.51