TECHNICAL DOCUMENTATION

SSP 052 Fabia 1,4 AMF 55kW TDI engine with unit injection system

PDFEN44 pages3 MB
SSP 052 Fabia 1,4 AMF 55kW TDI engine with unit injection system - PDF cover

This PDF is currently unavailable.

Read document text
SP52_02After the successful introduction of the 1.9-ltr. 4-cylinder TDI engine with pump-nozzle injection system for ŠkodaFabia, ŠkodaOctavia and ŠkodaSuperb, the trend of an economic, low emission and at the same time powerful, direct injection turbo diesel engine in ŠkodaFabia continues with the 3-cylinder TDI engine.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Through the removal of a cylinder the engine is lighter, it has fewer moveable masses and a lower friction than a 4-cylinder engine. It has a high performance potential for this class of vehicle despite its low displacement. In this Self-Study Program you can get acquainted with the engine of the new generation.2GB ContentsIntroduction Technical highlights Engine mechanical components Cylinder block Balance shaft Trapezoidal piston and trapezoidal conrod Toothed belt drive Engine lubrication Oil pump Oil filter holder Oil circulation Pump-nozzle injection system General Constructive installation Fuel supply Fuel system Electrical fuel pump Fuel cooling Engine cooling Coolant circuit Exhaust system Exhaust system Radiator for exhaust gas recirculation Component positions Overview Engine management System overview Sensors Actuators Preheating system Preheating system Additional heating Additional heating Function diagram Legend to function diagram Notes 4 4 6 6 6 9 10 12 12 14 15 16 16 17 18 18 20 21 22 22 23 23 23 24 24 26 26 28Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�3842 42 43 43 44 44 46Servicexxxxxxxxxxxxxxxx FABIAServicexxxxxxxxxxxxxxxx FABIAServicexxxxxxxxxxxxxxxx FABIAService Servicexxxxxxxxxxxxxxxx FABIA xxxxxxxxxxxxxxxx FABIAService Servicexxxxxxxxxxxxxxxx FABIA xxxxxxxxxxxxxxxx FABIAS e r v i c eXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXX XXXXXXXXYou will find notes on inspection and maintenance, setting and repair instructions in the Workshop Manual.GB3 IntroductionTechnical highlightsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP52_47Engine highlights – 1.4-ltr. TDI engine is developped on the basis of the 1.9-ltr. TDI engine with Pump-nozzle injection system – – – – – – – – – Cylinder block is made out of cast iron Cylinder removal and bore as shown in the basic model Engine 1.9-ltr. TDI Control drive via the toothed belt Balance shaft is driven via the chain by the crankshaft Vacuum pump is installed at the cylinder head and is driven by the camshaft Oil filter housing upright Oil pump is driven via a chain by the crankshaft Coolant pump integrated into the cylinder block Engine with pendulum bearing4GB Technical Data Engine code letters Design Displacement Bore Stroke Compression ratio Valve per cylinder Firing order max. power output max. torque Engine management Fuel Emission standard AMF 3-cylinder inline engine 1422 cm3 79.5 mm 95.5 mm 19.5 : 1 2 1-2-3 55 kW at 4000 rpm–1 195 Nm at 2200 rpm–1 Bosch EDC 15 P Diesel at least 49 CZ – DIN EN 590 or Biodiesel (RME*) – DIN E 51 606 EU3Power output/torque diagram80200The 1.4-ltr Engine produces power output of 55 kw at a speed of 4000 rpm–1. The maximum torque of 195 Nm is available at 2200 rpm–1. Power output and torque are based on operation of the engine with diesel fuel 49 CZ.701806016050 P (kW)140 M (Nm)Protected by copyright. Copying for private or commercial purposes, 120 in part or in whole, is not permitted 40 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�3010020801060M = Torque n = Engine speed P = Power output0100020003000400050006000n (min –1 )SP52_01*Rape seed oil fatty acid Methyl EsterGB5 Engine mechanical componentsCylinder blockThe cylinder block is manfactured out of cast iron.SP52_03Balance shaftThe differential shaft is located in the crank assembly of the engine. It reduces the oscillations and therefore ensures a smooth engine running. The balance shaft rotates at the same speed, but in the opposite direction of the crankshaft. The oscillations are caused by forces which are created when the piston and conrod are moving up and down and the rotational The balance shaft is guided in a ladder frame, movement of the crankshaft. These which is screwed to the cylinder block. It is oscillations are transferred via the align unit driven via the chain by the crankshaft. mounting onto the body. In order to reduce these oscillations, the balance shaft opposes Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted the forces of the piston, conrod and unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. crankshaft. Copyright by ŠKODA AUTO A. S.�Ladder frameCrankshaftDifferential shaft Hydraulic chain tensionerSP52_04Balance weight 6GB The differential shaft is mounted two times in the ladder frame. Two balance weights are on the balance shaft. The balance weight 1 is a component of the balance shaft. The balance weight 2 with the chain sprocket in a determined position is secured against twisting and is attached with a bolt to the balance shaft.Bracket Differential weight 2 Differential weight 1Chain sprocketLadder frameSP52_77Cylinder blockBushingThe brackets are components of the ladder frame. A cutout bushing is pressed into them. The joint of the bushings was notched for reasons of assembly.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The lubrication of the differential shaft is performed via an oil bore in the ring groove of the bushes.SP52_78Oil boreLubricating grooveGB7 Engine mechanical componentsMarkings for compensation of mass balance For an effective mass balance, the crankshaft and the balance shaft must run relatively to each other in the correct position. To do so, the markings of the chain sprocket of crankshaft and and the chain sprocket of balance shaft must be aligned with two coloured drive chain links when installing the drive chain. In order to achieve an even load compensation of the chain ,the number of the teeth on the chain sprocket of the crankshaft and the chain sprocket of the balance shaft as well as the number of chain links between the colour-marked chain links are selected, in such a way that after several rotations, the marked chain links are aligned again with the markings.Marking of crankshaft sprocket wheel Chain tensioner colour marked chain linkDrive chain sprocket of oil pumpSP52_05Marking of chain sprocket for balance shaftProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�8GB Trapezoidal piston and trapezoidal conrodA higher pressure in the combustion chamber is achieved through the combustion of the fuel air mixture. The components of the crank assembly are heavily loaded by the high combustion pressure. The piston hub and conrod eye are designed in a trapezoidal shape in order to decrease the stress of the piston, piston pin and conrod during high combustion pressures.LinerSP52_07SP52_79Combustion forceCombustion forceContact surfaceContact Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability surface with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP52_08SP52_09Enlarged contact surfaceConventional connection between piston and conrod.The contact surface of the conrod eye and piston hub at the piston pin is enlarged through its trapezoidal shape in comparison to the conventional connection between piston and conrod. Therefore the combustion forces are distributed over a larger surface. At the same time the piston, piston pin as well as the conrod are less stressed.9GB Engine mechanical componentsToothed belt driveLarge driving forces are required in order to produce an injection pressure of 200 MPa. These forces lead to a high stress of the components for the toothed belt. For this reason, the following measures apply, in order to balance the toothed belt: – Vibration damper A vibration damper is located in the camshaft sprocket, which reduces the vibrations in the toothed belt drive. Toothed belt The toothed belt is 30 mm wide. The load of the toothed belt is decreased through the large contact surface. Tensioning pulley The tensioning pulley of the toothed belt ensures a constant tensioning in case of varying load and temperature conditions. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Tensioning pulleyToothed belt Camshaft sprocket––Coolant pump gearSP52_83Guide pulleyAdjustment of the timing on camshaft A marking is located on the rear toothed belt protection for adjusting the timing. The adjustment marking for the 3-cylinder TDI Engine is marked as 3Z because the same toothed belt protection is fitted on the 3-cylinder engine as well as on the 4-cylinder engine. The camshaft is located in the position of the “TDC of cylinder 1”, if the lugs on the wheel hub are opposite the adjustment marking 3Z.Crankshaft gearLug on wheelhubAdjustment marking on the rear toothed belt protectionSP52_19Note: Please observe the instructions in the Workshop Manual for adjusting the time!10GB Split camshaft sprocket A split camshaft sprocket is used. The wheel hub with the vibration damper is one part of the camshaft sprocket. It is positioned on the cone of the camshaft. The installation position is defined through a nutspring connection. The other part is the camshaft gear, which is attached with bolts to the wheel hub. The camshaft is fixed in the position of the “TDC of cylinder 1“- in which the rig pin 3359 is placed into one hole of the wheel hub as well as into the cylinder head. The camshaft gear is turned in the elongated holes when tightening the toothed belt while the camshaft is locked in the position of the TDC of cylinder 1 by the rig pin 3359.CamshaftWheel hub with vibration damperCamshaft gearRig pin 3359Lug Adjustment markingSP52_20Crankshaft arrester T10050Adjustment of the timinig on crankshaft The crankshaft is fixed into position of “TDC of cylinder 1” with the crankshaft arrester T10050 which is pushed onto the crankshaft gear in the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted axial direction. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�MarkingSP52_21Crankshaft gearGB11 Engine lubricationOil pumpThe oil pump is a crescent pump. It is also designated as a Duocentric pump. The term “Duocentric” is based on the geometric offset of the axles from the internal and external rotor. The oil pump is attached to the ladder frame and is driven through the chain by the crankshaft. The chain is tightened by a hydaulic chain tensioner.Crankshaft sprocket Hydraulic chain tensioner Drive chain sprocket of oil pumpSP52_12Oil pumpOil pump housingDrive chain sprocket of oil pumpInstallation of oil pump The pressure limiting valve in the oil pump is a safety valve. It prevents that the components of the engine are damaged through high oil pressure, for example at low outside temperatures and high engine speeds.Housing coverSP52_13External rotor Internal rotorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Housing with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�cover (folded and turned)Pressure limiting valveSP52_1412GB Working mode of oil pump Ex tr act The internal rotor is fitted onto the drive shaft and drives the external rotor. The teeth run separately during the rotary movement because of the different pivots for the internal and external rotor. It creates a space enlargement on the suction side. This extracts the oil through a suction line and transports it further to the delivery side.Internal rotor Suction line Delivery side External rotorSuction sideProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� SP52_15Oil panDelivery sidePr o d uce pr ess ure On the delivery side the teeth of the internal and external rotor run again together. This makes the space between the teeth smaller. The oil is injected into the oil circulation system of the engine.Suction sideSP52_16Oil panGB13 Engine lubricationOil filter holderThe oil filter holder is positioned vertically. It has an exchangeable paper filter element to the top and is easy to maintain as well as environmentally friendly.Oil filter holderSP52_10The oil pressure regulator valve and the return-flow check tube are integrated in the oil filter holder. The short circuit valve is located behind the cap. In order to ensure that the oil flows out of the oil filter holder into the oil pan during the oil filter change, an oil drain hole becomes accessible when removing the paper filter element. Through this hole the oil can flow out of the oil filter holder into the oil pan.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or Short accept any liability circuit with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�CapvalvePaper filter elementOil pressure regulator valveOil drain holeSP52_11Return-flow check tube14GB Oil circulationVacuum pump Oil pressure switch Oil spray nozzle and piston cooling Short circuit valveOil filterTurbochargerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted valve unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S.regulator does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Oil pressureHydraulic chain tensioner Differential shaft Oil pump Pressure relief valve Return-flow check tubeSP52_06Oil coolerOil flow without pressureOil flow with pressureExternal oil lineThe pressure relief valve in the oil pump is a safety valve. It prevents that the components of the engine are damaged through high oil pressure, for example at low outside temperatures and high engine speeds. The oil pressure regulator valve controls the oil pressure of the engine. It opens as soon as the oil pressure has reached the maximum permissible value.The return-flow check tubes avoid when the engine is standing in still motion that oil flows out of the cylinder head and the oil filter holder back into the oil pan. The short circuit valve opens when the oil filter is plugged and through this secures the oil supply of the engine.GB15 Pump-nozzle injection systemGeneralWhat is a pump-nozzle unit? A pump-nozzle unit is, as its name says, an injection pump combined with solenoid valve and injection nozzle in one component. Each cylinder of the engine has a pump-nozzle unit. There is no high pressure in the fuel feed lines. This one is first of all produced in the pump-nozzle unit. So that the volumes to be compressed are very small and therefore a higher maximum injection pressure can be reached very quickly. The pressure reduction, start of injection and injection quantity are controlled by the engine management via the solenoid valves. This results in an optimal mixture formation and a good combustion, as well as a high production and low pollutant emisson when fuel consumption is low.Solenoid valveInjection nozzleSP52_25Pump-nozzle unit Fixing screwsThe pump-nozzle units are mounted directly in the cylinder head. They are attached with clamping pads in the cylinder head.Clamping padProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Glow plugSP52_26Note: Ensure correct installation position when installing the pump-nozzle unit. If the pumpe-nozzle unit is not perpendicular to the cylinder head, the fixing screw can loosen. The pumpe-nozzle unit or the cylinder head can be damaged through this. Please observe the instructions in the Workshop Manual.16GB Constructive installationRoller rocker armBall pins Injection camsBall pinsSolenoid valve needlePiston spring Solenoid valve Pump plunger Solenoid valve High pressure chamber O-ring Cylinder headAlternative pistonFuel return flowNozzle needle damping O-ring Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP52_23Fuel feedNozzle needleSP52_24Heat-protection seal Solenoid valve needle CirclipSP52_22SP52_84Solenoid valve Heat-protection sealGB17 Fuel supplyFuel systemThe fuel is pumped by an electrical fuel pump out of the fuel tank via the fuel filter to the mechanical fuel pump. The fuel is delivered from here via the feed channel in the cylinder to the pump-nozzle unit. The fuel which is not needed for the injection flows from the pump-nozzle unit via the returnflow channel back into the cylinder head, the housing of the mechanical fuel pump and the fuel cooler in the fuel tank.Fuel cooler Fuel return-flow Fuel feed Preheating valveFuel temperature sensorelectrical fuel pumpFuel filter Non-return valveElectrical fuel pumpoperates as predelivery pump and pumps fuel to the mechanical fuel pump.Fuel filterprotects the injection system against contamination and wear through particles and water. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedSP52_31unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information SP52_32 in this document. Copyright by ŠKODA AUTO A. S.�Fuel temperature sensorserves as a detection of the fuel temperature for the engine control unit.Fuel coolercools the flowing back fuel, in order to protect the fuel tank against fuel which is too hot.SP52_33SP52_2818GB Preheating valveonly opens the path to the fuel tank when the fuel temperature is above 30 °C. Through this the heat is concentrated at the engine and the engine can reach normal operating temperature faster.Check valveavoids when the engine is standing in still motion that fuel flows out of the fuel pump back into the fuel tank. (Opening pressure = 0.02 MPa)SP52_30SP52_29Pressure regulator valve (in fuel return flow)BypassThrottle hole (from fuel feed to fuel return-flow)Cylinder headSP52_27mechanical fuel pumpStrainerPressure regulator valve Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Throttle hole unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability (in fuel feed) with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�(from fuel feed to fuel return-flow)Pressure regulator valve (in fuel feed)regulates the fuel pressure in the fuel feed. When fuel pressure is above 0.75 MPa valve opens and fuel is lead to the suction side of the mechanical fuel pump.Fuel vapor bubbles, which are located in the fuel feed, are disposed of in the fuel return-flow via the throttle hole.BypassIf there is air in the fuel system, for example when fuel tank is empty then the pressure regulator valve remains closed. The air from the continuous flow of fuel is depressurized out of the system.Pressure regulator valve (in fuel return flow)maintains the pressure in the fuel return-flow at 0.1 MPa. The constant power ratios at the solenoid valve needle are achieved through this.Strainercollects the fuel bubbles out of the fuel feed. Finally they are disposed of via the throttle hole and returnflow.GB19 Fuel supplyElectrical fuel pumpThe electrical fuel pump is located in the fuel tank and functions as a predelivery pump. It pumps fuel to the mechanical fuel pump at the cylinder head. This ensures that in extreme situations (e. g. driving at maximum speed when outside temperature is warm) no fuel vapor bubbles could form from a too high negative pressure in the fuel feed. Irregularities in the engine running are avoided by the formation of vapor bubbles.Working mode of the electrical fuel pump E lect r ical principle The fuel pump relay is actuated by the engine control unit when ignition is on and activates the operating current for the electrical fuel pump. Simultaneously the pump runs for approximately 2 seconds and builds up a prepressure. It is switched off during the preheating in order to discharge the battery. As soon as the engine is turned on, the pump runs constantly.Pressure regulator valveFuel feed Fuel return flowFuel tankHydr aulic principleReservoirThe electrical fuel pump extracts the fuel via a filter from the reservoir. The delivery quantity is separated in the pump cover. One part is distributed in the fuel feed SP52_35 Protected by part copyright. for private or commercial purposes, in part or in whole, is not permitted to the engine and the other isCopying distributed unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability to the drive of the suction jet pump. Theoffuel is in this document. Copyright by ŠKODA AUTO A. S.� with respect to the correctness information Electrical fuel extracted out of the fuel tank by the suction jet Entrained fuel pump pump and is delivered in the reservoir of the electrical fuel pump. The pressure regulator Non-return valve in the pump cover limits the delivery Suction jet pump valve pressure to 0.05 MPa. This protects the fuel lines from a fuel pressure which is too high. Note: You will find detailed information regarding suction jet pump in the Self-Study Program No. 49.20GB Fuel coolingUnder high pressure in the pump-nozzle unit the fuel heats up so intensively that it must be cooled off before the fuel can flow back into the fuel tank. A fuel cooler is located under the vehicle floor for this purpose. It is fitted with severel installed parallel channels through which the backflow of the fuel can flow looped. At the same time the fuel is cooled though the outside air which flows along the cooler and the fuel tank as well the sender for the fuel supply is protected against fuel which is too hot.Fuel coolerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP52_34Fuel tankThe fuel coolerFuel from engineSP52_36Fuel to fuel tankGB21 Engine coolingCoolant circuitHeat exchanger for heating Expansion reservoirEngine Coolant pumpCoolant regulatorOil coolerCoolerSP52_17Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�large coolant circuit small coolant circuitNote: The oil cooler is located in the small coolant circuit.22GB Exhaust systemExhaust systemThe exhaust system of the 1.4 l/55 kW TDI engine is installed in the desired manner. It consists of a catalytic converter and a rear silencer.SP52_41Catalytic converterRear silencerRadiator for exhaust gas recirculationProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�A radiator for exhaust gas recirculation which is connected to the coolant circuit, is fitted on engines which must comply with the emission standard EU4. In order to enlarge the cooling surface, the metal body is provided with honeycomb shaped ducts which are cooled by the coolant. The exhaust flows back through the ducts and delivers the heat at the coolant. Because of the cooled off exhaust gases, the combustion temperature continues ro decrease and this leads to an additional reduction of the nitrogen oxides.SP52_42Coolant connection Cooling ducts (honeycomb shaped)Exhaust to intake manifoldExhaust from exhaust manifoldSP52_43CoolantGB23 Component positionsOverviewValves for pump-nozzle Cylinder 1 - 3 N240 - N242Valve block consists of: • Solenoid valve for exhaust gas recirculation N18 • Solenoid valve for charge pressure control N75 • Change-over valve for intake manifold flap N239Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Hall sender G40Intake manifold pressure sender G71 Intake manifold temperature sender G72Glow plugs Q624GB Coolant temperature sender G62Diesel direct injection system control unit J248Air mass meter G70SP52_50Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Fuel temperature sender unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by Š KODA AUTO A. S.� G81Engine speed sender G28GB25 Engine managementSystem overviewSensorsAir mass meter G70 Diesel direct injection system control unit J248Engine speed sender G28Hall sender G40Accelerator pedal position sender G79 Kick-down switch F8 Idling switch F60Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Coolant temperature sender G62 K-wireIntake manifold pressure sender G71 Intake manifold temperature sender G72 Clutch pedal switch F36 Brake light switch F and brake pedal switch F47Electrical system control unit J519Fuel temperature sender G81Auxiliary signals: Vehicle speed signal switch for CSS (ON/OFF) Generator Terminal DFM PTC heating ONDiagnostic connection26CAN DriveGB ActuatorsAltitude sender F96Fuel pump relay J17 fuel pump G6Glow plug relay J52 Glow plugs Q6Dash panel insert KValve for pump-nozzle cylinder 1 - 3 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does notN240 guarantee or accept any liability - N242with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Valve block consists of: • Solenoid valve for exhaust gas recirculation N18 • Solenoid valve for charge pressure control N75 • Change-over valve for intake manifold flap N239 Glow period warning lamp K29 Exhaust emission warning lamp K83 Low heat output relay J359 Heating element for additional heating Z35 High heat output relay J360Oil level/ oil temperature sender G266SP52_49GB27 SensorsHall sender G40The hall sender is attached to the toothed belt protection below the camshaft sprocket. It touches the teeth on the sensor rotor of the camshaft which is connected to the camshaft sprocket.Sensor rotor of camshaftUse of signal The signal from the Hall sender is used by the engine control unit for detecting the cylinders when engine is started.Hall senderSP52_37Effects of signal failure In the event of a signal failure the engine control unit uses the signal from the engine speed sender G28.+30Electrical circuitJ322Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�18J248101 109Note: You will find detailed information regarding Hall sender in the SelfStudy Program No. 51.SG40o+SP52_3828GB The cylinder detection when engine is startedWhen engine is started the engine control unit must know which cylinder is located in the compression stroke, in order to actuate the corresponding valve for the pump-nozzle. It also evaluates the signal from the Hall sender. The Hall sender touches the teeth from the sensor rotor of the camshaft. This determines the position of the camshaft as well as the position of the respective piston.Cylinder 1Cylinder 312 0°The sensor rotor of the camshaft Because the camshaft makes a rotation of 360° per working cycle, there is for each cylinder one tooth at a distance of 120° on the sensor rotor. In order to assign the teeth to the cylinders, the sensor rotor has an additional tooth for cylinder 1 and 2 with varying distances.SP52_39Cylinder 2Working mode of sensor rotor Each time a tooth of the sensor rotor rotates past the Hall sender, a Hall voltage is generated which is conducted further to the engine control unit. The engine control unit detects from the varying distances of the signals the cylinders and can actuate the corresponding valve for the pump-nozzle.Signal indication of Hall sender G40120°120°120°Cylinder 1Cylinder 2Cylinder 3SP52_40Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB29 SensorsEngine speed sender G28The engine speed sender is an inductive sender. It is attached to the cylinder block.SP52_44Engine speed sender The engine speed sender touches 54 teeth (60 – 2 – 2 – 2) of the sensor rotor, which is attached to the crankshaft.Use of signal The speed of the engine and the exact position of the crankshaft is detected by the signal of the engine speed sender. The injection point and the injection quantity is calculated according to this information.SP52_45Effects of signal failure If the signal of the engine speed sender fails, the engine is switched off. A restarting of the engine is not possible.Electrical circuitJ248Protected by copyright. Copying for private or commercial purposes, in part or in whole, 110 102is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�G28SP52_4630GB Quick-start detection In order to enable a quick start, the engine control unit evaluates the signal from Hall sender and from the engine speed sender. The engine control unit detects the cylinder with the signal from the Hall sender which touches the sensor rotor of the camshaft. It receives a reference signal already after one third of a crankshaft rotation through the 3 gaps on the sensor rotor of the camshaft. The engine control unit detects through this already very early the position of the crankshaft and can actuate the corresponding solenoid valve in order to introduce the injection procedure.Signal indication of engine speed sender G28U 1t 3 2SP52_51U t 1 2 3Voltage Time Tooth Tooth gaps GapsSignal indication of Hall sender and engine speed sender G281 Camshaft rotationHall sender G40120°120°120°Cylinder 1Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability of Cylinder 3information in this document. Copyright by ŠKODA AUTO A. S.� Cylinderwith 2 respect to the correctnessEngine speed sender G281 Crankshaft rotationSP52_52GB31 SensorsAccelerator pedal position sender G79The accelerator pedal position sensor is a component of the accelerator pedal module. The accelerator pedal module consists of an accelerator pedal, sensors and a pedal block. The external structure is identical to the accelerator pedal module of the electrical accelerator control on petrol engines. The following sensors are located in the accelerator pedal module: • the accelerator pedal position sender G79 • the idling switch F60 • the Kick-down switch F8Pedal blockSP52_82SensorsAccelerator pedalThe gas accelerator pedal position sender G79 is a sliding contact potentiometer. The resistance value alters with every change of the accelerator pedal position. The idling switch F60 and the Kick-down switch F8 are sliding switches. If the sliding contact is located on the individual slideway, the resistor approximately 900 Ω (testable between the contacts 5 and 6 at the sender) and the idling or kick-down switch are closed. If the sliding contact is outside the slideway, the resistance is infinte and the switch is opened.Puller with sliding contacts Conductor plate with slidewaysSP52_81Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Use of signal The gas acce lera tor peda l positio n s e n d e r G 7 9 transmits the current accelerator pedal position and uses this information as a main influence variable for calculating the injection quantity. The idling s witch F 6 0 indicates to the engine control unit that the accelerator pedal is not operating. The Kick- do wn switch F 8 is used only for vehicles with automatic transmission.32GB Sliding contactSlideway of sender G79 Slideway of switch F60 Consumer Slideway of switch F8Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP52_80Effects of signal failure Without the signal the engine control unit cannot detect the accelerator pedal position. The engine continues running with increased idle speed, so that the driver can reach the next workshop.Electrical circuitJ248 51 70 63 69 50 12F60/F8G79SP52_56Note: The sensors consist of slideways and sliding contacts. The sliding contacts are positioned together on one consumer, which is attached to one shaft.GB33 SensorsThe following sensors were already described in the other Self-Study Programs for TDI Engines, for this reason they are not clearly explained here.Air mass meter G70The air mass meter with reverse current detection determines the extracted air mass. It is located in the intake pipe. Reverse currents of the extracted air mass occur in the intake pipe when opening and closing the valves. The air mass meter with reverse current detection detects the reverse current air mass and takes it into account for the signal to the engine control unit. Through this the measurement of the air mass is precise.Use of signal The measured values are used by the engine control unit for calculating the injection quantity and the exhaust gas recirculation quantity.Effects of signal failure In case of signal failure of the air mass meter, the engine control unit calculates with a fixed replacement value.SP52_64Coolant temperature sender G62The coolant temperature sender is located at the coolant connection of the cylinder head. It informs the engine control unit about the current coolant temperature.Use of signal The coolant temperature is used by the engine control unit as correction value for the calculation of the injection quantity.Effects of signal failure If the signal fails, the engine control unit calculates as a replacement value with the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted signal from the fuel temperature sender. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP52_5734GB Intake manifold pressure sender G71Use of signal The signal for the intake manifold pressure sender is required for the checking of the charge pressure. The determined value is compared by the engine control unit with the specified value from the charge pressure performance. If the actual value differs from the specified value, the charge pressure is readjusted by the engine control unit via the solenoid valve for charge pressure control. Effects of signal failure The control of the charge pressure is no longer possible. The engine has less power output.Intake manifold temperature sender G72Use of signal The signal of the intake manifold temperature sender is required by the engine control unit as a correction value for the calculation of the charge pressure. Through this the temperature influence on the density of the charge is taken into account. Effects of signal failure In case of signal failure, the engine control unit calculates with a fixed replacement value. This can incur a loss of power output.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP52_58Note: The intake manifold pressure sender G71 and the intake manifold temperature sender G72 are located in one component in the intake manifold.GB35 SensorsAltitude sender F96The altitude sender is located in the engine control unit. Use of signal The altitude sender reports to the engine control unit the current ambient pressure. This one is dependent on the geographic altitude. An altitude correction is performed with the signal for the charge pressure control. Effects of signal failure Black smoke can appear in the altitude.SP52_72Clutch pedal switch F36The clutch pedal switch is located at the pedal assembly. Use of signal The engine control unit detects through the signal if the clutch is engaged or disengaged. The injection quantiy is reduced for a short time when operating the clutch pedal. This Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted prevents an engine jerk during gearshifts. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Effects of signal failure In case of signal failure from the clutch pedal switch, load changes can occur during gearshifts.SP52_5936GB Brake light switch F and brake pedal switch F47The brake light switch and brake pedal switch are located together in one component at the pedal assembly. Use of signal Both switches deliver to the engine control unit the signal “Brakes operating”. If the accelerator pedal position sender could be defective, the engine is regulated for safety reasons when the brake is operated. Effects of signal failure If one of both switches fail, the fuel quantity is reduced by the engine control unit. The engine has less power output.SP52_60Fuel temperature sender G81The fuel temperature sender is a temperature sensor with a negative temperature coefficient (NTC = Negative Temperature Coefficient). This means the resistance of the sensor decreases when the fuel temperature increases. It is located in the fuel return-flow line between the mechanical fuel pump and the fuel cooler. The sender determines the current fuel temperature. Use of signal The engine control unit requires the currrent fuel temperature for the calculation of the start of delivery and the injection quantity in order to take into account the density of the fuel when temperatures differ. Effects of signal failure In case of failure of the sender, the engine control unit gives a fixed value as a calculation basis. This failure of the signal is indicated in the dash panel insert by the exhaust emission Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability warning lamp.with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP52_61GB37 ActuatorsValves for pump-nozzle N240 - N242The valves for the pump nozzle are attached with a union nut to the pump-nozzle units. They are solenoid valves which are actuated by the engine control unit. Start of delivery and injection quantity are controlled by the engine control unit via the valves for the pump-nozzle.Start of delivery As soon as the engine control unit actuates a valve for the pump-nozzle, the solenoid valve needle is pressed into the location by the solenoid coil and closes the path from the fuel feed to the high pressure chamber of the pump-nozzle unit. Then the injection procedure begins.Injection quantity The injection quantity is determined through the actuation period of the solenoid valve. As soon as the valve for the pump-nozzle is closed, the fuel is injected into the combustion chamber.SP52_62Effects of failure If a valve for the pump-nozzle fails, the engine running is rough and the power output is lower. The valve for the pump-nozzle has two safety functions. If the valve remains open, no pressure can build up in the pump-nozzle unit. If the valve remains closed, the high pressure chamber of the pump-nozzle unit can no longer be filled. In both cases no fuel is injected into the cylinder.Electrical circuitJ248 114 116 118 121N240Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�N241N242SP52_6338GB The following actuators were already described in the other Self-Study Programs for TDI Engines, for this reason they are not clearly explained here.Solenoid valve for charge pressure control N75The solenoid valve for charge pressure control is an electropneumatic valve. It is integrated together with N18 and N239 in one valve block. The valve switches the control pressure for operating the charge pressure control valve.SP52_68The engine reaches its highest torque with an adjustable turbocharger.SP52_65Charge pressure control The solenoid valve for charge pressure control is actuated by the engine control unit. The control pressure is determined depending on the on/off ratio of the signal with which the charge pressure control valve is operated. Through this the quantity of the exhaust current is controlled which is directed to the turbocharger drive on the turbine wheel. The control pressure is formed from the atmospheric pressure and the charge pressure.Charge pressure control valveCharge air coolerExhaust gas Solenoid valve for charge pressure controlProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Atmospheric pressure Charge pressure Control pressureSP52_66Effects of failure If the solenoid valve for charge pressure control fails, the engine power output is lower.39GB ActuatorsValve for exhaust gas recirculation N18The valve for exhaust gas recirculation is integrated together with N75 and N239 in one valve block. It is an electropneumatic valve. The valve switches the control pressure for operating the exhaust gas recirculation valve. The exhaust gas recirculation is a measure for reducing the nitrogen oxides in the exhaust. One part of the exhaust gases is added to the intake air. Through this the oxygen content is decreased in the combustion chamber and the combustion temperature is lowered. The lower combustion temperature leads to a lower discharge of nitrogen oxides. In full load operation no exhaust gas is returned, because a higher oxygen share in the combustion is required for a good power production.SP52_68Working mode The exhaust gas recirculation is controlled via a performance map in the engine control unit. At the same time the valve for exhaust gas recirculation is actuated by the engine control unit. The control pressure is determined depending on the on/off ratio of the signal with which the exhaust gas recirculation valve is operated. Through this the quantity of the returned exhaust gases is controlled. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Exhaust gas recirculation valveValve for exhaust gas recirculation Vacuum pumpRadiator for exhaust gas recirculation (only for engines which must comply with the exhaust emission standard EU4)SP52_67Exhaust gas Vacuum Atmospheric pressure Control pressureEffects of failure The exhaust gas recirculation is not guaranteed. This failure is indicated in the dash panel insert by the exhaust gas warning lamp.40GB Change-over valve for intake manifold flap N239The change-over valve for intake manifold flap is integrated together with N18 and N75 in one valve block. It switches the vacuum for operating the intake manifold flap in the intake pipe. The intake manifold flap interrupts the air supply when the engine is switched off. Through this less air is compressed and the engine runs smoothly.SP52_68Note: On diesel engines the intake manifold is of special importance because of the high compression pressure of the extracted air. Copying for private or commercial purposes, in part or in whole, is not permitted Protected by copyright. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability It avoids jerk movements when with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� switching off the engine.Intake manifold flap Change-over valve for intake manifold flap N239Working mode If the engine is switched off, the engine control unit sends a signal to the change-over valve for intake manifold flap. This switches the vaccum for the vacuum box. The vaccum box closes the intake manifold flap.Engine control unit J248SP52_69Ignition lockVacuum boxGlow period warning lamp K29The glow period warning lamp K29 is located in the dash panel insert and has the following tasks:SP52_71– to indicate the glowing period before starting the engine – warning lamp comes on – to display a fault – warning lamp flashes (when engine is running) Effects of failure The warning lamp does not come on and does not flash. A fault message is stored in the fault memory.GB41 Preheating systemPreheating systemThe preheating system facilitates the starting of the engine at low temperatures. It is switched on by the engine control unit when the coolant temperature is below +9 °C. The glow plug relay is actuated by the engine control unit. It switches on the work current for the glow plugs. The system overview indicates from which sensors the signals for the preheating system are used and which actuators are actuated.System overview of preheating systemEngine control unit J248Engine speed sender G28Glow plugs Q6 Glow plug relay J52Coolant temperature sender G62 Glow period warning lamp K29SP52_73The glowing isProtected divided into two phases. by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Preglowing After switching on the ignition, the glow plugs are switched on when the coolant temperature is below +9 °C. The glow period warning lamp comes on. If the glowing procedure is finished, the warning lamp goes off and the engine can start.After-glowing After each engine start it is after-glowed, not depending on the preglowing. Through this the combustion noises are reduced, the idling quality is improved and the carbon dioxide emissions are reduced. The after-glowing phase lasts maximum 3 minutes and is interrupted at engine speeds above 2500 rpm–1.42GB Additional heatingAdditional heatingThe TDI Engines develop little waste heat for reasons of their high efficiency. Under certain circumstances there is not enough heat output available. This is why for certain countries an additional heating element is fitted in the heating box.SP52_74Additional heating elementHeat exchangerIt is mounted in the air flow behind the heat exchanger.Air flowHeat exchanger Additional heating elementSP52_75The additional heating element consists of aluminium contact panels with shaft ribs and fifteen ferrous ceramic PTC resistors which Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability PTC resistor are divided into three heating elements. It with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� heats the passing flow of the air and ensures a quick heating up of the passenger seating compartment. PTC resistors have their highest conductivity in cold condition. They have a positive temperature coefficient (PTC = Positive Temperature Coefficient). They are heated by the flowing through current. With increasing temperature the resistance increases while the current flow is decreased.Silicone sectionAluminium contact panels with shaft ribsSP52_76GB43 Function diagramLegend to function diagramComponents A F F8 F36 F47 F60 G6 G28 G40 G62 G70 G71 G72 G79 G81 J17 J52 J248 J322 J359 J360 J519 J533 N18 N75 N79 N239 N240 N241 N242 Q6 S Z35 Battery Brake light switch Kick-down switch Clutch pedal switch Brake pedal switch for CCS/ Diesel direct injection system Idling switch Fuel pump (pre-delivery pump) Engine speed sender Camshaft position sensor Coolant temperature sender Air mass meter Intake manifold pressure sender Intake manifold temperature sender Accelerator pedal position sender Fuel temperature sender Fuel pumpe relay Glow plug relay Diesel direct injection system Diesel direct injection system relay Low heat output relay High heat output relay Electrical system control unit Databus diagnostic interface+30 +15SSSSN239 N79N75N18 +G40o-+A-4581626110910152733171110 102G72Valve for exhaust gas recirculation Solenoid valve for charge pressure control Heating resistor (crankcase ventilation) Change-over valve for intake manifold 31 flap Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Valve for pump-nozzle, cylinder 1 in this document. Copyright by ŠKODA AUTO A. S.� with respect to the correctness of information Valve for pump-nozzle, cylinder 2 Valve for pump-nozzle, cylinder 3 Auxiliary signals Glow plugs (engine) A Generator DFM Fuse B Switch for CCS ON/OFF Heating element for additional heating C PTC-heating ON D Vehicle speed signalG71G2844GB J533J519+30 +15SJ322J52 S S SJ17G70Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does F not guarantee F47 or accept F36 any liability J359 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�J360Q63768493016671842 J248123265662122517063 69501238 14 1520112104 11110311411611812180 S S S SA BF60/F8 G79C DG62 G81N240N241N242M4 G6Z3531inoutSP52_48Colour coding = Input signal = Output signal = Bidirectional = Voltage supplyGB= Earth = CAN databus = Diagnostic connection45