TECHNICAL DOCUMENTATION

SSP 054 Škoda Octavia The second generation – Electrical Components

PDFEN52 pages2 MB
SSP 054 Škoda Octavia The second generation – Electrical Components - PDF cover

This PDF is currently unavailable.

Read document text
Service ŠkodaOctaviaThe second generation Electrical components54Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Self-study programme unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability This self-study programme informs you about the design and with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� the function of certain components of the electrical components for the second generation of ŠkodaOctavia.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted ContentsOnboard supply CAN databus system LIN databus Gateway Onboard supply control unit Dash panel insert 4th generation of immobiliser Convenience electrics Steering column switch Light Windscreen wiper Tyre inspection Trailer detector control unit Personalization Coming Home/Leaving Home Mobile phone-Voice control system Self-diagnosis4 8 13 15 19 20 23 24 33 35 38 41 43 44 45 46 50Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted You will find detailed inspection, setting and unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information inrepair this document. Copyright by ŠKODA AUTO A. S.� repair instructions in the provided manuals.The time of going to press was on the 22.3.2004. The contents are not updated.GB3 Onboard supplyThe fuse boxes and relay positions in the onboard supplyThe onboard supply in the second generation of ŠkodaOctavia is designed decentralized. Because of the diffferent installation conditions, the fuse boxes and the relay positions are located at different locations in the vehicle. These components are mounted decentralized. This means, they are located close to their relevant components and functional groups.The functioning of the entire system in the vehicProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability le is controlled by a series of specialised control with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� units. The communication between the control units and other functional groups of the electrical system is performed via CAN databus line.Electric box in engine compartment (E-box)4GB Fuse boxOnboard supply control unitProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP54_01Additional relay carrier below the dash panelGB5 Onboard supplyThe fitting locations in the onboard supply - overview and characteristics The fuse boxThe fuse box is located in the left dash panel.SP54_02The relayThe additional relay carrier below the dash panel comprises the following components: • Thermal protection for the driver seat memory. • Headlight washer system relay. • Fuel pump relay.SP54_03The following relays are located on the front side of the onboard supply control unit: • Terminal 30 voltage supply relay. • Heated rear window relay J9. • Dual tone horn relay J4. • Double washer pump relay -1- J729. • Double washer pump relay -2- J730. • Terminal 75X X-contact relay.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP54_046GB The electric box (E-box)Because of a large number of electronic components, a number of fuses and relays had to be increased for better accessibility as well as the improvement of the self-diagnosis. Certain fuses and relays are placed in the E-box located on the left in the engine compartment. The fuses and relays placed in the E-box assist the function in particular of the electrical components located in the engine compartment.On the front side of the E-box are the main fuses of the electrical system, which supply the current to the following electrical components:• Generator. • Electro/mechanical power steering. • Radiator fan. • Terminal X. • Electrical auxiliary air heater. • Terminal 30.SP54_05Protected by copyright. Copying for private or well commercial Depending on the equipment, the fuses as as purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability the following relays placed in the withare respect to the correctness of E-box: information in this document. Copyright by ŠKODA AUTO A. S.�• Voltage supply relay terminal J329 (terminal 15). • Voltage supply relay terminal J682 (terminal 50). • Fuel pump relay J17. • Glow plug relay -J52. • Voltage supply relay terminal J317 (terminal 30).SP54_06GB7 CAN databus networkingThe CAN databus networking conceptK-wire CAN databus diagnosis J533 Gateway CAN databus combi J285 Control unit in dash panel insert CAN databus drive J386 Driver door control unit J527 CU for steering column electronics G85 J412 CU for operating electronics, mobile phone R12 Amplifier J345 CU for trailer detector J387 Front passenger door control unit Steering angle sender J217 CU for automatic gearbox J743 Direct shift gearbox mechatronics*Diagnostic connection T16 J503CU for display unit for radio and navigationCAN databus infotainmentCAN databus convenienceJ543 CU for seat adjustment with memoryJ446 CU for parking aidJ388 Rear left door control unitLIN databusE221J587 CU for selector lever sensors*Multi-function steering wheelJ255/J301CU for Climatronic, air conditioning systemJ389G273J...J583Engine control Interior monitorRear right door CU for NOx unit in part or in whole, is sensor Protected by copyright. Copying private or commercial purposes, not permitted ing for sensor control unitunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�J400 CU for wiper motor LIN databus G397 Rain and light detector sensorJ604 CU for auxiliary air heaterJ393 Convenience system central control unit LIN databusH12 Alarm hornJ431 CU for headlight range control J104 CU for ABS Separate CAN databusJ519 Onboard supply control unitG384 Vehicle inclination senderG419 ESP sensor unitJ500 CU for steering aidJ234CU for airbag* only on gearbox 02ESP54_078GB The networking of the CAN databus cablesCAN databus combi Cable colourCAN H - orange/purple CAN L - orange/brown Transmission speed 500 kbit/sCAN databus diagnosis Cable colourCAN H - orange/black CAN L - orange/brownTransmission speed 500 kbit/sAt the CAN databus combi, the communication is only performed between the Gateway and the dash panel insert.The CAN databus diagnosis serves as a data transfer between the diagnostic unit VAS 5051/5052 and the GatewayJ285 CU for display unit in dash panel insert Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�J533 Gateway Diagnostic connection T16SP54_08GB9 CAN databus networkingCAN databus driveTransmission speed 500 kbit/sCable colourCAN H - orange/black CAN L - orange/brownJ500 CU for steering aidJ... Engine control unit J743 Direct shift gearbox mechatronics*J217 CU for automatic gearboxJ104 CU for ABSJ527 CU for steering column electronicsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�J431 CU for headlight range controlJ533 GatewayJ234 CU for airbagSP54_09J587 CU for selector lever sensors* * only on gearbox 02E10GB CAN databus convenienceTransmission speed 100 kbit/sCable colourCAN H - orange/green CAN L - orange/brownJ604 CU for auxiliary air heaterJ519 CU for onboard supplyJ533 Gatewayauthorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability J527 CU forunless steerwith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� ing column electronicsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedJ393 Convenience system central control unitJ386 - J389 Door control unitJ255 CU for Climatronic or J301 CU for air conditioning systemJ345 CU for trailer detector J543 CU for seat adjustment with memoryJ446 CU for parking aidSP54_10GB11 CAN databus networkingCAN databus infotainmentTransmission speed 100 kbit/sCable colourCAN H - orange/purple CAN L - orange/brownJ533 GatewayJ503 CU for display unit for radio and navigationProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�R12 AmplifierJ412 CU for operating electronics, mobile phoneSP54_1112GB LIN databusThe modern vehicles of today are equipped with a lot of control units. In order to ensure their proper function, a mutual data transfer is absolutely necessary. The previous methods for transmitting information via individual line connections are already limited. The LIN databus (Local Interconnect Network) is therefore used more frequently together with the increasing number of control units connected directly via the CAN databus cable.In the second generation of ŠkodaOctavia, the LIN databus is distributed in the following three subsystems: • Onboard supply control unit. • Convenience system central control unit. • Steering column electronics control unit. In contrast to the CAN databus cable, only one cable is sufficient for the correct function. Another one-wire purple cable with a white marking is used. The cable has neither a screening nor another malfunction protection.SP54_12E221 Operating unit in the steering wheel G273 Interior monitoring sensor G384 Vehicle inclination sender Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted G397 and light detector sensor unless authorised by ŠKODA AUTO A. S. ŠKODA AUTORain A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� H12 Alarm horn J393 Convenience system central control unit J400 Wiper motor control unit J519 Onboard supply control unit J527 Steering column electronics control unitGB13 LIN databusIts own communication is initiated exclusively by the master control unit, which is connected directly to the CAN databus cable. This control unit is also independently self-diagnostic and controls simultaneously the complete communication process. The slave control unit cannot respond without request for data transfer. It is fully dependent on the master control unit. The master control unit can control up to 16 control units. The transmission speed of the LIN databus in the second generation of ŠkodaOctavia is 19.2 kbit/s.Tasks of the master control unit• Ratio and data transmission between LIN and CAN databus. • Monitoring of the data ratio and the speed of the data transmission.Message header transmitter: LIN masterMessage header content transmitter: LIN master or LIN slaveUProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Battery unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability voltage with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Recessive voltage levelDominant voltage level0SP54_13t14GB GatewayThe Gateway is an independent control unit, which is fitted under the dash panel above the accelerator pedal. The function of the Gateway control unit is in principal identical to the previous model. The control unit transmits information between the individual CAN databus cables.SP54_14Combi wake-upCAN databus combi15 30 30 31 31CAN databus drive CAN databus convenience CAN databus infotainmentProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability CAN databus di- to the correctness of information in this document. Copyright by Š with respect KODA AUTO A. S.� SP54_15 agnosisDiagnostic connection T16GB15 GatewayThe control units connected to the CAN databus are in home position when the ignition is switched off. Through this it is possible to achieve a low current consumption. The control of these conditions is carried out by the Gateway control unit.Sleep modeAs soon as the last control unit of the CAN databus convenience and infotainment has transmitted its sleep mode readiness, the Gateway control unit gives the sleep command. If the CAN databus drive does not go into sleep mode, the CAN databus convenience and the CAN databus infotainment also do not go into sleep mode. If the CAN databus convenience does not go into sleep mode, the CAN databus infotainment also does not go into sleep mode. This is how a control unit can stop the vehicle from going into sleep mode.Master functionsThe Gateway control unit controls at the CAN databus cable the following functions: • Terminal 15 castor. • Sleep mode. • Wake-up mode. • Transport mode.Terminal 15 castorCertain control units also need the possibility to continue communicating after „ignition off“. This is why a message for controlling the castor is transmitted to the CAN databus cable. The control units switch internally a connection from terminal 30 to terminal 15 and continue to communicate.Wake-up modeIf the control unit detects a pulse for activation, it sends a signal to the CAN databus cable. The Gateway control unit finally activates the other control units at the CAN databus cable.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Control units which participate in the The CAN databus drive is activated after the igunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness in this document. Copyright bydatabus ŠKODA AUTO A. S.� nition of isinformation switched on. The CAN convencastor:• Engine control unit. • ABS control unit. • Steering aid control unit. • Automatic gearbox control unit. • Steering column electronics control unit. • Control unit for selector lever sensors.ience and CAN databus infortainment are activated by opening the doors, switching on the hazard warning system, opening the tailgate, switching on the ignition etc.Control units which do not participate in the castor:• Airbag. • Control unit for headlight range control.16GB The coding of the GatewayThe coding of the Gateway control unit differs completely from the previous coding of the Gateway or from the new long coding of the convenience system central control unit and the onboard supply control unit. When coding the Gateway control unit, the mechanic must first of all have an overall view of the control units connected to the CAN databus cable. Then he must inspect the control units or assign them to the Gateway listed in the list. This is required for the mutual communication of the control units. Afterwards the manufacturer, the body version, the steering type and the number of doors have to be selected. However the end code cannot be found. In case of an incorrect coding, only one message regarding an incorrectly performed coding is displayed in the fault memory.01 - Motor electronics 02 - Gearbox electronics 22 - Four-wheel drive electronics 42 - Driver door electronics 52 - Front passenger door electronics 62 - Rear left door electronics 72 - Rear right door electronics 03 - Brake electronics 44 - Steering aid 15 - Airbag 25 - Immobiliser 55 - Headlight range control 65 - Tyre pressure monitoring 75 - Emergency call modulecoded not coded not coded coded coded coded coded coded coded coded coded not coded not coded not codedSP54_16SP54_17coded - the Gateway control unit is coded for the communication with the respective control unitProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB17 GatewayThe battery transport modeThe transport mode enables a reduction of the current consumption of the battery for transportation to the dealers. This function is controlled by the Gateway control unit. The transport mode is set in the self-diagnosis. The switching on of the transport mode is the result of the number of kilometers driven. After the first 150 km, the transport mode can no longer be switched on.The transport mode deactivates the following systems:• Radio. • Interior lighting. • Interior monitoring. • Inclination sensor. • Save LED in the driver‘s door.SP54_18SP54_19Display of the battery transport modeProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�18GB Onboard supply control unitThe onboard supply control unit is located on the driver side under the dash panel. Relays are mounted on its front side.SP54_20SP54_21The onboard supply control unit is obtainable in two versions: • For vehicles with fog lights and personalization. • For all other vehicles. The individual versions differ only in their indexes.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Main functions of the control unit:• Electrical load management. • Interior and exterior light control. • Reversing lights. • Bulb monitoring. • Fuel pump feed (pressure build-up). • Windscreen wiper and washer system. • Dual tone horn. • Function enable for seat heating and sliding/ tilting roof. • Heated rear window. • Terminal control 15, 75X, 50.SP54_22Note! In the lower part of the control unit there is a mechanical fuse, which should prevent disconnection of most of the plugs.GB19 Dash panel insertSP54_23The following components are integrated in the dash panel insert: • Control unit for display unit in the dash panel insert J285. • Immobilizer control unit J362. • Speedometer. • Rev counter. • Fuel gauge display. • Coolant temperature gauge. • Warning lights. • Multifunction display.Self-diagnosis of the dash panel insertThe diagnosis of the control unit in the dash panel insert is carried out via CAN databus diagnosis using the diagnostic unit VAS 5051/5052. In the self-diagnosis, the following components can be checked with the function „actuator test“:• Rev counter. • Coolant temperature gauge. • Fuel gauge display. • Speedometer. • Read out on the display. All warning lights are in the LED version. • Warning light for immobiliser. • Warning light for overheating. • Warning light for brake pad wear. • Warning light for fuel reserve. • Warning light for oil pressure. • Warning light for oil level. • Warning light for driver seat belt. Note! • Warning light for two-circuit brake system and After changing the dash panel insert, handbrake. the coding and the adaptation have • Gong. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted to be by carried out on the other vehicle unless authorised ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee accept any liability •or Warning buzzer. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� systems. • Turn signal system, audible feedback. In the control unit J285 all information is processed by the monitoring functions and passed on to the warning lights as pulses for lighting up, flashes or permanent lights. The lighting up of certain warning lamps is performed in combination with an acoustic signal. 20 GB Warning light symbolsThe readout on the display varies depending on the dash panel insert version.Versions• Lowline - Basic version • Midline - with multifunction display • Highline - with Maxi DOT displaySymbolWarning light Right turn signal system Left turn signal system GeneratorLowline 4Midline 4Highline 4Meaning flashes simultaneously with the right turn signal flashes simultaneously with the left turn signal fault in the vehicle recharging system4444 Engine hood 4 Bulb failure 4 Tyre pressure monitoring Main beam light 4 Low beam light 4 Rear fog light 4 Airbag 4Electronic Power Control (electronic throttle)44 open engine hood *4DOT44bulb filament for side, low beam or brake light destroyed tyre pressure too low *444 main beam light44 low beam light44 rear fog light44 fault at airbag44 fault in EPC system444TCS = Traction lights up - TCS off, ESP off or fault in the sysProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted control system ESP tem; flashes - system active unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability in this document. Copyright by ŠKODA AUTO A. S.� 4 to the correctness 4 of information 4 = Electronic stabil- with respect ity program Preglowing 4 ABS 4 4 4 4 4 flashes - fault in the motor electronics (diesel engine) fault in ABS systemGB21 Dash panel insertSymbol Warning light OBD - Onboard diagnosis (onboard diagnosis) Steering aid 4 4 4 Lowline 4 Midline 4 Highline 4 Meaning lights up, fault in the exhaust gas relevant engine electronics; flashes, possible catalytic converter damage fault in the system of the electro/mechanical power steeringImmobiliser 4 Coolant level or overheating Brake monitoring 4 Washing water 4 Brake pad 4 Fuel reserve 4 Oil pressure 4 Oil level 4 4 4 4 4 4 4 4 4when lighting up, there is a start attempt with an unauthorised key coolant shortage or overheating *44DOTbrake fluid shortage, handbrake applied *DOTwashing water shortageDOTauthorised brake pad minimum thicknessDOTreserve in fuel reservoir *DOToil pressure in engine lubrication system too low lights up, engine oil level too low *; flashes,Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised AUTO A. S.fault ŠKODA A. S. does not guarantee or accept any liability 4 by ŠKODA DOT inAUTO the oil level/temperature sender with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�DOT - the symbol of the warning light is shown as pictograph in the DOT display 4 - the warning light is shown in the dash panel insert outside the DOT display * The lighting up of the warning lamp is performed in combination with an acoustic signal - peepNote!The activation of the symbol on the display occurs in most cases when the engine is running or when driving.22GB 4th generation of immobiliserThe 4th generation of immobiliser improves the protection against unauthorized operation of the vehicle. The system ensures an electronic protection for the engine control unit.AdaptationThe prerequisite for the correct function of the system is the adaptation of the components to each other. First the engine control unit has to be adapted, which takes over the specific vehicle code and the password of the immobiliser control unit from the immobiliser control unit and in return transmits the password for the engine control unit and the blocking code of the engine control unit to the immobiliser control unit. After checking the correct code for certain vehicle makes, the keys are adapted (they take over the specific vehicle code from the immobiliser control unit and the immobiliser control unit takes over the fixed code of the key).DesignThe system consists of a transponder in the key, an engine control unit and an immobiliser control unit.The vehicle key contains: - Electronic transponder with fixed code. - Specific vehicle code of immobiliser. - Manufacturer code for certain vehicle makes (e.g. the VW keys cannot be used for Škoda).The engine control unit contains: - Password for the engine control unit. - Blocking code for the engine control unit (prevents the adaptation of another control unit instead of the original engine control unit). - Code for certain vehicle makes. - Specific vehicle code for the communication with the immobiliser.SP54_24The immobiliser control unit contains: unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability •Š The of the code for certain group makes, - Specific vehicle with respect tocode. the correctness of information in this document. Copyright by KODA use AUTO A. S.� which prevents the use of different components - Password of the immobiliser control unit. amongst Škoda, VW, etc. - Blocking code for the engine control unit (pre• All versions of the engine control unit have the vents the adaptation of another control unit inso-called „Tuning protection“ (prevents the enstead of the original engine control unit). gine control unit being replaced with a control - Code for certain vehicle makes. unit with higher power output). • Coded data transfer between the immobiliser control unit and the engine control unit. Explanations • Specific vehicle code - defines the behaviour of • Different cryptic algorithm for the key and the engine control unit. the immobiliser. • Password (random digit code) of the immobiliser control unit or the engine control unit. Note! • Blocking code for the engine control unit - preThe waiting time for the adaptation of vents the adaptation of another control unit inthe new components to the system is stead of the original engine control unit. 5 minutes for the keys and the immo• Code for certain vehicle makes - e.g. Škoda, VW, biliser control unit and 10 minutes for etc. the engine control unit.GB 23Differences between the 3rd and 4th generation Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Convenience electricsThe convenience electrics ressembles the one in the first generation of ŠkodaOctavia. The self-diagnosis of the door control units, a complete new type of coding for the convenience system central control unit (the so-called „long coding“) and the introduction of the LIN databus are part of the essential changes. The convenience system central control unit is located under the dash panel above the glove compartment, next to the airbag holder.Amongst the important functions of the convenience system central control unit are:• Control and inspection of the central locking. • Actuation of the rear doors. • Actuation of the tailgate release • Actuation of the tank release. • Actuation of the anti-theft alarm system via LIN databus.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Note! Before pulling the plug out of the convenience system central control unit, first of all the control unit must be slightly pushed out of the holder.SP54_25SP54_2624GB The door control unitsJust as for all the other control units at CAN databus these control units are also about the self-diagnosis. However the „long coding“ is not used for coding the door control units. The innovation represents the use of two control motors in the locking unit. Thus a lower malfunction susceptibility as well as a faster locking is achieved.Emergency running functionThe following emergency running functions are started, if a door control unit is disconnected from the CAN databus cable. • If all the control units receive five times consecutively no message from the convenience system central control unit, the driver side door control unit ensures the control. • If a door control unit is supplied with current and cannot communicate via the CAN databus, then the window can still be operated ten minutes after the last message from the CAN databus with the switch for the electrical window actuation which is connected to this control unit.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�• In case of a failure of the CAN databus communication between the convenience system central control unit and the door control unit, the vehicle can be locked by pressing down the stopping lever up to the inner stop. The stopping lever is located under a panel on the front side of the door.SP54_27Stopping lever in basic positionThe self-diagnosis of the door control units is performed via the following address words: • 42 - Driver door electronics. • 52 - Front passenger door electronics. • 62 - Rear left door electronics. • 72 - Rear right door electronics.SP54_28GB25 Convenience electricsThe long codingThis new type of coding was installed up to now only at the convenience system central control unit, the onboard supply control unit and the Gateway. The coding of the Gateway control unit is however different in comparison to the other two control units. The coding of the convenience system central control unit and the onboard supply control unit is in principal identical. The difference exists only in the length of the hexadecimal code. The hexadecimal code for the convenience system central control unit has only 26 digits, but the code for the onboard supply control unit has 34 digits. After the diagnostic unit VAS 5051/5052 is connected and the function „long coding“ was selected, the table with the current coding of the control unit appears. If the convenience system central control unit is coded, 13 bytes are shown on the left of the screen, from which each consists of an eight digit number block. Each position (byte) in this number block has its specific meaning. E.g . the 0 in the 10th byte on the position 4 from the left means, that it concerns a vehicle with a left-hand drive The meaning of the individual bytes is determined by the code table dependent on the vehicle equipment. The new control unit already has the group basic coding. This coding must be adapted however in accordance with the individual equipment and specification from Škoda. The mechanic can code with the help of either the binary code or the hexadecimal code.Byte indexHex 00 F8 00 00 7F 2D 85 05 48 CF 86 10 04Byte pattern 00000000 11111000 00000000 00000000 01111111 00101101 10000101 00000101 01001000 11001111 10000110 00010000 00000100Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�01 2 3 4 5 6 7 8 9 10 11 12Remove byteHexBinSP54_17SP54_2926GB The vehicle inclination senderWith its function in active condition, it protects the vehicle against undesirable towing. It is located together with the interior monitoring sensor under a cover in the area of the front interior lighting.Operation:The function of the sender consists of measuring the vehicle inclination angle and analysing each random change of this angle. If an inclination change is detected above the limit value, the sender control unit carries out a more detailed analysis of the inclination angle. Then the sender control unit measures this angle with extreme sensitivity and checks continuously, if the limit value for the alarm activation was exceeded. If the determined inclination angle is above the limit value, the anti-theft warning system is activated.SP54_30The switch for deactivation of the vehicle inclination sender is located on the driver side, in the bottom „B-pillar“, together with the switch for deactivation of the interior monitoring sensor.The convenience system central control unit monitors the complete course of communication. The communication between the convenience system central control unit and the vehicle inclination sender is performed via the LIN databus.The function of the vehicle inclination sender can only be deactivated with the switch when leaving the vehicle. The vehicle inclination sender is deacProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unlessthe authorised by ŠKODA AUTO A. S.ignition ŠKODA AUTO does not guarantee or accept any liability tivated by pressing switch when the isA. S. The inclination angle of the sender can be checked with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� switched off (terminal 15), the key is removed from in the measured value block. For the correct disthe ignition lock (S-contact) and the driver door is play of the current value, the sender must be in opened. Then the vehicle must be locked within 30 the active condition. seconds.Switching off the vehicle inclination sender is only carried out for one locking cycle.X-reference angle current X-delta angle Y-reference angle current Y-delta angleSP54_17 SP54_31 SP54_32GB27 Convenience electricsThe interior monitoringThe interior monitoring is performed by three ultrasound sensors. The sensors are located under a cover in the area of the front interior lighting. After the vehicle is locked, the anti-theft alarm system and the interior monitoring are activated automatically. If one of the doors is open when activating the anti-theft alarm system, its monitoring is activated with a time delay of 5 seconds after closing the door. The interior monitoring is only activated after closing all the monitoring points and after the activation time of 20 seconds has elapsed. Depending on the input signals (window open, installation of auxiliary heater) the control unit sets the sensitivity threshold for the alarm triggering. If the vehicle is locked by radio control, this condition of the convenience system central control unit is also transmitted to the CAN databus. The convenience system central control unit activates the interior monitoring sensor via the LIN databus. If there is a possibility that an alarm could be triggered through movement in the locked vehicle, the interior monitoring must be deactivated when leaving the vehicle. The switch for deactivation of the interior monitoring sensor is located on the driver side, in the bottom „B-pillar“. The interior monitoring can only be deactivated by means of the switch when leaving the vehicle. The vehicle inclination sender is deactivated by pressing the switch when the ignition is switched off (terminal 15), the key is removed from the ignition lock (S-contact) and the driver door is opened. Then the vehicle must be locked within 30 seconds. Switching off the interior monitoring is only carried out for one locking cycle.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP54_3328GB The function of the ultrasound systemPhase „A“ deactivation status inactiveThe microprocessor of the ultrasound system is normally in idle state. It evaluates no ultrasound signals and blocks the emission of the ultrasound. The microprocessor is actuated regularly by a timer or by the convenience system central control unit. The system communicates with the convenience system central control unit via LIN databus and under its command it moves into the phase „Analysis of an activation attempt“. the convenience system central control unit. The convenience system control unit informs about the error for 28 seconds by means of the light diode in the driver door. The system moves into the deactivation state.Phase „C“ analysis of an activation attempt The microprocessor of the ultrasound system is in operating condition. It generates the frequency for the transmission of an ultrasound signal, which is generated by one of the sensors. It generates signals, which are indispensable for the incidental demodulation of the received ultrasound signals.Phase „B“ connected in monitoring statusThe microprocessor of the ultrasound system is normally in idle state. It is actuated every 200 milliseconds by the monitoring timer. In active condition, the system transmits It evaluates signals, which come from 4 analog interrupted ultrasound signals and evaluates their re- channels (2 per receiver). The alarm is activated, sponse signals which are received by three sensors. If if the signals have the same frequency and are out the receiving signal matches the previously received of phase by 90°. signals, the microprocessor returns to idle state. If the receiving signal is different in comparison to the previ- In the case of an authorized alarm, the ultrasound Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by Š KODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability ous signal, the system moves into the phase „Analysis system transmits a message the LIN databus to with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.via � of an activation attempt“.the convenience system central control unit.This analysis can trigger the alarm. Otherwise the system returns to the cyclic analysis of the response signals. The sensitivity of this system is regulated automatically when working with response signals. After the activation the maximum sensitivity is decreased in stages, until no further signal changes indicating a movement inside the vehicle are detected. This automatic control is performed within two minutes after the activation. The microprocessor is actuated every second by the LIN databus, which transmits the messages regarding the current operating state. Under command of the convenience system central control unit, it can move into the phase „Deactivation“ or „Diagnosis“. The system evaluates the voltage and the operating temperature in regular intervals of one minute. If the measured values are within the tolerance, the system moves into the phase „ Analysis of an activation attempt“. The system sends an error message toWhile deciding about the alarm triggering, the system remains in this phase or exits it. If these signals do not lead to an alarm triggering, the system returns to the monitoring phase. The convenience system central control unit can bring the system into the phase „Deactivation „ or „Diagnosis“ via the LIN databus. Phase „D“ diagnosisThe microprocessor of the ultrasound system is in operating condition. It is controlled by the convenience system central control unit. The system is set to the phase „Deactivation“ or „Analysis of an activation attempt“.GB29 Convenience electricsThe alarm hornThe alarm horn is located in the front right wheelhouse above the wheelhouse liner.After locking the vehicle, the LIN databus performs an active communication between the convenience system central control unit and the alarm horn. The convenience system central control unit transmits a message every second to the alarm horn regarding the current vehicle status. The message is evaluated by the alarm horn and the anti-theft alarm system is activated on command for alarm triggering or when communication is interrupted. The alarm horn has its own Ni-MH-cells. These are supplied directly with current from the fuse box.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP54_3430GB The locking inspectionOutside lockingIn the second generation of ŠkodaOctavia, the safety knob is no longer a component of the door lock. The message regarding the status of the safety knob for central locking is partially ensured by the locking warning light, which is connected directly to the driver side door control unit. In the initial condition the warning light informs precisely about the status of the central locking. The control signal of the warning light is activated by the convenience system central control unit. If the vehicle is locked and the anti-theft alarm system is deactivated or there is a fault, the warning light shows various conditions.Inside lockingThe warning light for inside locking informs the customer about the condition of the inside locking. The warning light serves as illumination of the central lokking switch, which is located in the centre console. The switch lights up orange: • If the vehicle is locked automatically. • If the vehicle is locked 2x consecutively within 2 seconds using the key via the lock cylinder or with the radio control. • If the vehicle with the central locking switch is lokked centrally.Vehicle without anti-theft alarm system.Locking with radio control or with a key via the lock cylinder.Vehicle with anti-theft alarm system. Locking with radio control or with a key Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted via the lock cylinder..Vehicle without anti-theft alarm system.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�When locking the vehicle 2x consecutively within 2 seconds using a key via the lock cylinder or with radio control.No signalVehicle with anti-theft alarm system. When locking the vehicle 2x consecutively within 2 seconds using a key via the lock cylinder or with radio control.No signalSP54_36Vehicle with anti-theft alarm system. Central locking or interior monitoring defective.Permanent signalSP54_35 2s 30 s For reasons of secrecy, the locking warning light is always actuated with a 0.5 Hz pulse after 30 seconds.GB31 Convenience electricsThe Memory seatThree differently set seated positions can be stored with the seat memory function The settings are stored in the control unit, which is located in the lower part of the seat. In contrast to the first generation of ŠkodaOctavia, the lumbar is also controlled additionally by the control unit. The stored settings can be requested using the position buttons at the driver seat or after adaptation of the radio control by pressing the button „Unlock“ on the radio control or after opening the driver door. Each time the control unit for seat adjustment with memory is changed, a setting must be carried out, which is absolutely necessary for the correct functioning of the memory seat. The limit values are stored in the „EEPROM memory“, so that no other setting is required. When connecting to the onboard supply for the first time, all senders and actuators are automatically read and assigned by the control unit. The position of the exterior mirrors is stored together with the current seated position.SettingPosition the backrest up to the front stop when the ignition is switched on. The Gong in the dash panel insert confirms that the setting has been carried out.Store seat positionPress the „SET“ button for one second when the ignition is switched on. Then press one of the memory buttons within 10 seconds for 1 to 3 seconds. Adapt the radio control to the seat position: Switch off the ignition (terminal 15), pull the ignition key out of the ignition lock (S-contact) and press the button „Unlock“ on the radio control within 10 seconds after pressing one of the memory buttons 1 to 3.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness Memory buttons 1-3 of information in this document. Copyright by ŠKODA AUTO A. S.�„SET“ button for memory functionLumbar settingButtons for seat settingSP54_3732GB Steering column switchCharacteristicThe steering column switch integrates the operating elements which are located at the steering column in one unit. At the same time it communicates between the operating elements located at the steering column and other vehicle systems. This communication is ensured by the steering column electronics control unit (J527), which is a component of the steering column switch. The steering column electronics control unit detects and processes all signals from the operating elements at the steering column and transmits them to the individual vehicle systems. In direction of the steering wheel the communication is performed via the LIN databus, in direction of the vehicle it is performed via CAN databus convenience and CAN databus drive.SP54_391. Ignition lock - ignition starter switch - The ignition lock transmits the movement from the lock cylinder to the ignition starter switch and closes the steering rod. - The ignition starter switch switches the signals for the onboard supply of the vehicle.2. Connection line - It serves as a connection of the steering column electronics control unit the Protected by copyright. Copying for private or commercial purposes, in part with or in whole, is ignition not permitted starter unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability switch and the electronic ignition key withdrawwith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� al lock on an automatic gearbox (not a component of the ignition starter switch). 3. Carrier body 4. Turn signal lever - It operates the turn signal lights, headlight flasher, main beam, side light and cruise control system. 5. Windscreen wiper lever - It operates the front and rear windscreen wiper and washer system. 6. Steering angle sender - It measures the steering angle values for the steering aid and also for the ESP. 7. Restoring ring with slip ring - They transfer signals between the steering wheel, signal horn, multifunction steering wheel and airbag.SP54_388. Steering column electronics control unit (J527) - It evaluates the signals from the individual components and communicates with the other vehicle systems. 33GB Steering column switchOperation:• Switching of base signals for the onboard supply by the ignition starter switch. • Transmitting signals between the vehicle and the steering wheel (signal horn, multifunction steering wheel - communication via LIN databus, airbag). • Operating turn signal lights, headlight flasher and main beam. • Operating windscreen wiper and washer system. • Operating onboard computer. • Operating cruise control speed (at turn signal lever). • Measuring steering angle and signal transmission in the vehicle. • Ignition key withdrawal lock (for automatic gearbox), if the selector lever is not in position „P“ (lock function).Note!The steering column electronics control unit is self-diagnostic under the address word 16 - steering wheel electronics.AirbagSignal hornButton for MFS* Steering wheel electronics* MFS - Multifunction steering wheelSignal hornGroundIllumination for MFS* AirbagVoltage supply for MFS*Restoring ring with slip ring Steering angle senderTurn signal lever Headlight flasher main beam CCS switchWindscreen wiper lever Steering column electronics control unit Onboard computerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�CU for airbagIgnition starter switchCSS Input/output Terminal 15 and terminal 50 Terminal 30 - Voltage supply Terminal 31 Signal from selector leverSP54_40CAN databus convenience Ignition lock CAN databus drive34GBSteering rodSteering wheelLIN LightThe onboard supply control unit J519 evaluates the signals directly from the light switch or from the light sensor. The information about switching on the turn signal light, the main beam and the headlight flasher is transmitted via the steering column electronics control unit via the CAN databus cable to the onboard supply control unit J519.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP54_41D E19 E4 F F4 G397 J527 J519 M25 XIgnition lock Parking light switch Headlight dipper/flasher switch Brake light switch Reversing light switch Rain and light detector sensor Steering column electronics control unit Onboard supply control unit Additional brake light Number plate lightGB35 LightHeadlightThe clear glass is made out of plastic. The headlight forms a unit, which is divided in three reflex surfaces: • Main beam light. • Low beam light. • Parking and turn signal light. For the second generation of ŠkodaOctavia two headlight versions are obtainable as an option. The parking and turn signal lights are covered with a scattering filter. The bulb for the turn signal is orange.Two chamber headlightMain beam light Low beam light Turn signal and parking lightSP54_42Headlight with dioptric-eliptic elementDepending on equipment, either a halogen or a xenon lamp can be inserted in the headlight with dioptric-elipitic element.Main beam lightProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP54_43Low beam light Turn signal and parking light36GB Reversing lightsThe reversing lights are designed so that the tail light at the entire outer circumference of the reversing light lights up and creates the so-called C-effect. 4 bulbs are used for the tail light - two single-filament bulbs for the tail light, one twofilament bulb for the tail light and brake light and one two-filament bulb for the tail light and fog light. The clear glass is inserted for the turn signal and reversing light. The component of the reversing light lens forms a reflector.Light sensorThe light sensor is fitted in the foot of the interior mirror. It forms together with the rain sensor one unit. The vehicles equipped with the light sensor can automatically detect the surrounding brightness and on the basis of this the driving light is switched on or off . The light sensor measures the light values at three different levels in front of the vehicle. Because of the difference between these light values, it can detect the current surrounding brightness (darkness, daylight, fog, driving into a tunnel, driving out of tunnel, driving in an alley etc.)Darkness A X B X C X X X X Driving into a tunnel, a forest, a garage etc. X Bridge, Alley Driving out of a tunnel, a forest, a garage etc. on Light A B C Surrounding brightness Darkness Daylight Light on offXSP54_44XXXXon onDirection indicatorsThey are installed in the exterior mirrors. They Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted consist of three LED unless authorised by diodes. ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�XXXFunction of the light sensorSP54_45SP54_46GB37 Windscreen wiperD E F266 G397 J104 J400 J519 J527 J533Ignition lock Windscreen wiper lever Contact switch for engine hood Positions of the windscreen wiper lever Rain and light detector sensor ABS control unit Wiper motor control unit Onboard supply control unit Steering column electronics control unit Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Gateway unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP54_47The signal of the position of the windscreen lever is passed on by the steering column electronics control unit via the CAN databus convenience to the onboard supply control unit J519. The onboard supply control unit transmits the signal about the current position of the windscreen wiper lever via the LIN databus to the wiper motor, where this signal is processed.SP54_480 - Basic position 1 - Interval wipe, controlled by the rain sensor 2 - Slow wipe 3 - Fast wipe 4 - Flick wipe, setting and service position 5 - Automatic wipe/wash 6 - Rear window wipe 7 - Automatic wipe/wash for rear window A - Switch for interval wipe and for sensitivity setting of the rain sensor38GB Wiper functionsSpeed dependent interval stages The wiping can be set using the windscreen wiper lever in four interval stages. The speed of the individual interval stages is dependent on the vehicle speed. The rest periods between the individual wiping intervals vary between 1.28 seconds in stage „I“ at approx. 150 km/h and 24 seconds in stage „IV“ at approx. 4 km/h.Speed dependent wiping stage resetting If the vehicle speed drops below 4 km/h (e.g when stopping at a traffic light post), the selected wiper speed is automatically decreased from stage 3 to stage 2 or from stage 2 to interval wipe (stage 1). When increasing the speed over 8 km/ h the wiper speed returns to the selected stage. One time washing of the windscreen If the button for the wash function is operated for more than 0.8 seconds, the fast wipe is switched on. If the operating time is low, the slow wipe is switched on.SP54_49Stage I Stage IIStage III Stage IVAntiblock function If the wiper on the windscreen encounters an obstacle, it can detect it. Then it attempts to push away this obstacle. If it cannot remove the obstacle, the wiping stops automatically after 5 wiping intervals and the wiper remains in front of the obstacle. After removing the obstacle and switching on the wipe system again, the wiper begins to wipe again.Wiping vehicles fitted with rain sensor Protected by copyright. Copying for rain private senor commercial purposes, in part or in whole, is not permitted The wiper frequency is controlled by the unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability respect to the correctness information in this document. Copyright by ŠKODA AUTO A. S.� sor. The windscreen with wiper lever must of be in the position for interval wipes. The setting of the sensor sensitivity can be performed with the windscreen wiper lever (position A).SP54_50GB39 Windscreen wiperAutomatic wash/wipe for windscreen If the windscreen wiper lever at the steering wheel is pulled back into the position of the wash function, the wash system begins to operate immediately, the wiper wipes with a time delay (800 milliseconds). At a vehicle speed above 120 km/h the wash and wipe system operates simultaneously. After releasing the lever, the wash pump stops and another 3 to 4 wiping intervals are carried out (depending on the duration of washing) Rewipe the windscreen At a vehicle speed above 120 km/h and when activating the wash system, another rewipe occurs again 5 seconds after the last rewipe. Service position for replacing the wiper blades This function cannot be activated if the engine hood is open. After activating this function, the wipers move into the position where the wiper blades can be replaced without damage. The function is activated by the windscreen wiper lever set in the position for flick wiping within 20 seconds after switching off the ignition. The wipers then move into service position.Alternative rest position After each second time when the windscreen wiper is switched off or after each fifth time when the ignition is switched off, the rest position of the windscreen wiper is newly defined, which should prevent a deformation of the wiper blades. In order to facilitate the setting of the windscreen wipers at the works or for the pre-sale service, this function is switched off during the first 100 wiping intervals.SP54_52Switching off the wipers when the engine hood is open This function was introduced for the purpose of safety increase during service work .If the engine hood is opened when the vehicle is in standstill or at a vehicle speed below 2 km/h, Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. the S. ŠKODA AUTO A. S. does notoperate. guarantee or accept liability wipers do not Theany wipers only start with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� wiping, after the engine hood is closed and the windscreen wiper lever was set in the position for wiping. If the engine hood opens at a speed of 2 km/h up to 16 km/h, the wipers stop. However, they can be switched on again by setting the windscreen wiper lever once again in the position for wiping. If the engine hood opens at a speed of more than 16 km/H, the signal from the hood contact is not accepted by the wipers.SP54_51Rest position after the second switching off Rest position after the first switching off40GB Tyre inspectionThe tyre inspection is a software module in the ABS control unit. The ABS control unit compares the circumferential speed on all 4 wheels and determines on the basis of the determined values and their possible deviations the pressure loss in the tyres.The roll-off circumference of a tyre depends on its inflation pressure. When changing the tyre inflation pressure, the roll-off circumference of the tyre changes as well. If a pressure loss is detected, the driver is made aware of this through the warning light lit up permanently in the dash panel as well as a brief buzzing tone. The warning is only set back after a new calibration.ABS wheel sensorsButton for tyre inspection displaySP54_53J104 J285 J533ABS control unit Control unit in dash panel insert Onboard supply control unitNote!In case of extremely fast cornering, when braking or activating an ABS system, the tyre inspection display temporarily switches off automatically.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB41 Tyre inspectionBasic setting (calibration)For determining the reference data, a calibration must be carried out after each change of the inflation pressure or after a tyre change.Calibration driveThe button for the tyre inspection display must be pressed in order to start a calibration drive. The warning lamp for the tyre inspection display lights up and the flashing of the warning lamp confirms the start of the calibration.SP54_54Button for tyre inspection displayThe system can only conduct a major monitoring after several minutes in a specific speed category, which is important in order to collect reference data in different speed categories. The system is fully operational only when sufficient data has System fault beenProtected collected. The driving distance for the caliby copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Ifora fault occurs in the ABS control unit, the tyre unlessdrive authorised by ŠKODA AUTO S. ŠKODA AUTO on A. S. does not guarantee accept any liability bration should be A. performed country with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� inspection is rendered non-operational and the roads or motorways. warning lamp for the tyre inspection display flashes.Calibration statusThe status of the calibration can be read out with the diagnostic unit VAS 5051/5052 via the „targeted fault finding“.42GB Trailer detector control unitOperation• It detects if a trailer is attached. • It switches and monitors the lights of the trailer. • It indicates defective bulbs in the lights of the trailer (tail light, brake light and turn signal light): The reverse and rear fog light cannot be indicated. • It ensures the automatic deactivation of the rear fog light on the vehicle, if a trailer is attached. The trailer detector control unit is self-diagnostic. The diagnosis is carried out using the diagnostic unit VAS 5051/5052. The lighting up of the trailer lights can be set by the coding. The trailer lighting is activated by the onboard supply control unit via the CAN databus. The lighting is switched through semi-conductors; no power load takes place for the control elements of the vehicle illumination.The trailer detector control unit is located in the luggage compartment on the left wheelhouse below the trim panel.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� SP54_55GB43 PersonalizationWith the help of the information display, the user has the possibilty to change certain settings. The current setting is displayed in the information display on the respective point at the top below the line. The setting is conducted using the buttons on the windscreen wiper lever. The menu selection is requested, when the rocker switch is held pressed for more than 1 second. The personalized menu is shown via the display in the dash panel insert. The transmission of the selected settings to the control units is performed via CAN databus convenience or CAN databus combi.By means of adaptation, the user can set the following system profiles:• Display language. • Warning for winter tyres. • Setting of the control units. • Light setting. • Time. • Setting of the functions for the convenience system central control unit.Rocker switch for menu request and choice of the individual menu fieldsSP54_56Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP54_58Display of the selected dataSP54_5744GB Coming Home/Leaving HomeComing HomeIn contrast to the first generation of ŠkodaOctavia, where this function was connected to several control elements, in the second generation of ŠkodaOctavia this function is controlled completely by the onboard supply control unit. This function enables the switching on of the low beam light when the ignition is switched off. Activation: - Switch off the ignition when the low beam light is switched on. - Keep the light switch in the position of the low beam light. The light goes off as soon as the set and active time constant with the help of personalization has expired.