TECHNICAL DOCUMENTATION

SSP 056 Direct Shift Gearbox DSG

PDFEN58 pages8 MB
SSP 056 Direct Shift Gearbox DSG - PDF cover

This PDF is currently unavailable.

Read document text
The automatic gearbox DSG* is available in the new ŠkodaOctavia, designated as Direct Shift Gearbox - abbreviated DSG. It can function in two operating modes: – fully automatically or – with the manual gear selection – the so-called Tiptronic The automatic gearbox DSG combines the advantages of the manually shiftable gearbox and the classical automatic gearbox in a successful way while at the same time suppressing their disadvantages. Shifting occurs fast, completely smooth and soft, without any jolting. It lasts only three to four hundredth seconds. The power transmission from the engine to the wheels is not interrupted when shifting. The gearbox shifts into a sporty shifting mode only at a higher speed and thus makes it possible to fully use the power potential of the engine. It shifts beforehand in the economic driving mode. Thus the fuel consumption is kept at a low level.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�*Direct Shift GearboxGB2 ContentsIntroduction Technical highlights Selector lever Actuation Structure of the selector lever Selector lever lock solenoid N110 Ignition key removal lock Structure of the DSG Basic principle Torque input Plate clutches Drive shafts Output shafts Reverse shaft Differential gear Parking lock Synchronization Torque transmission in the vehicle Power flow in the gears Mechatronics module Electrohydraulic control unit Oil circulation System overview Sensors Actuators Function diagram 4 4 6 6 7 8 10 12 12 13 14 16 18 20 21 22 23 24 25 28 30 32 40 42 50Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� 56CAN data bus linkage Self-diagnosis58 59ServiceOCTAVIA IIII OCTAVIAXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXXXXXXXX XXXXXXXS e r v i c eYou will find notes on inspection and maintenance, setting and repair instructions in the Workshop Manual.XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXGB3 IntroductionTechnical highlightsThe manual shift gearboxes dominate in Europe in the current gearbox world, meanwhile the automatic gearboxes are primarily available in the USA and Japan. Both kinds of gearboxes have specific advantages and disadvantages. The advantages of a manual shift gearbox are among others. – – a high degree of efficiency as well as robustness and sportyness.An advantage of an automatic gearbox is among others. – high convenience, particularly when changing the gears (without interruption of the traction force).Before this background Volkswagen set itself the goal to unite the advantages of both gearbox worlds in a completely new gearbox generation, the automatic gearbox DSG.Pressure oil filterOil coolerOil pumpMechatronics Multi-plate clutchSP56_01Based on its conception with two multi-plate clutches and different automatic shift programs, it fulfils the high requirementsProtected for comfort from the drivers of vehicles with gearbox. by copyright. Copying for private or commercial purposes, in part orautomatic in whole, is not permitted Beyond this it offers pure driving fun to the drivers of vehicles with manual shift gearbox through direct influence and very fast, jerk-free shifts.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�At the same time the fuel consumption is equal to the one of economical vehicles with manual shift gearbox.4GB Characteristics for the automatic gearbox DSG are:– – – –six forward gears and one reverse gear normal driving program „D“, sport driving program „S“ direct shifting with the selector lever - Tiptronic Mechatronics, electronic and electrohydraulical control unit form a unit and are accommodated in the gearbox Hillholder function - rolls the vehicle while stationary with easily operated brake, the clutch pressure is increased and the vehicle is stationary Creep control - makes "creeping" of the vehicle possible without operating the driving pedal, for example when parking due to the design it can only be driven in the 1st or 3rd gear or only in the 2nd gear in the emergency operation programme depending on the occuring fault–––Pressure oil filterOil coolerElectrical connection to the vehicleProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted SP56_02 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB5 Selector leverActuationThe selector lever is operated in the same way as on a vehicle with automatic gearbox. The automatic gearbox DSG offers also the possibility of shifting with Tiptronic. The selector lever is available, as for vehicles with automatic gearbox, via selector lever locks and ignition key removal locks. The function of the locks has remained the same. The design is new.The selector lever positions are: P – Parking For moving the selector lever from this position, the ignition must be"on" and the foot brake must be applied. In addition, the release button on the selector lever must be pressed. N – Neutral position In this position the gearbox is in idle. If the selector lever is in this position for a longer period, the foot brake must be applied when leaving this position.Release buttonD – Drive In this lever position (Drive = Fahrt), the forward gears are automatically shifted. R – Reverse gear The release button must be pressed, in order to engage this gear.SP50_03S – Sport The automatic gear selection is performed according to a "sporty" characteristic, which is stored in the control unit for automatic gearbox. + and – Tiptronic functions can be carried out in the right selector lever gate.6Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB Structure of the selector leverSelector lever sensor control unit J587 Hall sensors in the selector lever support detect the position of the selector lever and make these available via the CAN bus of the mechatronics. Selector lever lock solenoid N110 Through the solenoid, the selector lever is locked in the positions „P“ and „N“. The selector lever lock solenoid N110 is actuated by the selector lever sensor control unit J587. Selector lever switch locked in P F319 If the selector lever is in the position „P“, the selector lever switch locked in P F319 sends the signal - selector lever in position „P“ to the steering column electronics control unit J527. The steering column electronics control unit needs this signal for the actuation of the ignition key removal lock.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Locking pin catch for „P“Selector lever switch locked in P F319 Locking pin Selector lever lock solenoid N110Locking pin catch for „N“Selector lever sensor control unit J587SP56_05Hall sensorsGB7 Selector leverSelector lever lock solenoid N110It functions as follows: Selector lever position „P“ locked The selector lever lock solenoid N110 is deenergized, the locking pin latches into the locking pin catch for „P“ by means of the spring force. The selector lever is locked.Selector lever lock solenoid N110 Pressure springLocking pin catch for „P“ Locking pinProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_06Selector lever position „P“ unlocked The selector lever lock solenoid N110 is energized by the selector lever sensor control unit J587. The locking pin is pulled against the spring force from the locking pin catch for „P“. The selector lever lock is removed.- +SP56_078GB Selector lever position „N“ If the selector lever with “ignition ON” is in the position "N" for longer than 2 seconds, the selector lever lock solenoid N110 is energized by the selector lever sensor control unit J587. The locking pin is pressed against the spring force into the locking pin catch for „N“. The selector lever is locked. As of a speed of approx. 5 km/h, the N lock is no longer activated.- +Locking pin catch for „N“SP56_08Selector lever position „N“ unlocked By actuating the foot brake and/or when "ignition off" the selector lever lock solenoid N110 is de-energized. The locking pin is pulled by the spring force out of the locking pin catch for „N“. The selector lever lock is removed.SP56_09Emergency release The access to the emergency release mechanism is possible after the removal of the console cover. By actuating the emergency release, the locking pin of the selector lever lock solenoid N110 is pressed against the spring force out of the locking pin catch for „P“. The selector lever can be moved out of the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability position „P“.with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_77GB9 Selector leverIgnition key removal lockThe ignition key removal lock prevents a turning back of the ignition key in the removal position when parking position is engaged. functions electromechanically and is actuated by the steering column electronics control unit J527.Ignition key removal lock solenoid N376It functions as follows S e l e c t o r l e v e r i n „ Pa rk pos i ti on“, t h e i g n i t i o n i s s wi tc he d off.SP56_10If the selector lever is in the park position, the selector lever switch locked in P F319 is opened. The steering column electronics control unit J527 detects the opened switch.The ignition key removal lock solenoid N376 is not energized. The pressure spring in the solenoid presses the locking pin into the loose position.J527Retaining lug+F319SP56_11Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Pressure springLocking pinIgnition OFF10GB S e l e c t o r l e v e r i n „ D ri v e pos i ti on“ , t h e i g n i t i o n i s s wi tc he d on.In the drive position of the selector lever, the selector lever switch locked in P F319 is closed. The steering column electronics control unit J527 energizes the ignition key removal lock solenoid N376.The locking pin is pushed by the solenoid, against the force of the pressure spring, into the locking position. In the locking position the locking pin prevents that the ignition key can be turned back and removed.J527-+F319SP56_12Ignition key removal lock solenoid N376Ignition ONOnly if the locked in P F319 opens and the steering column electronics control unit J527 shifts the ignition key removal lock solenoid N376 de-energized. Thereupon the locking pin is pressed back by the pressure spring. The ignition key continues to turn and can be pulled out.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect is to the correctness of information in this position, document. Copyright ŠKODA AUTO A. S.� selector lever pushed into the park the by selector lever switchGB11 Structure of DSGBasic principleThe automatic gearbox DSG consists in principle of two partial gearboxes independent from each other. Each partial gearbox is designed functionally like a manual shift gearbox. A multi-plate clutch is assigned to each partial gearbox. Both multi-plate clutches run with DSG oil. They are regulated, opened and closed by the mechatronics depending on the shift gear. The 1st, 3rd, 5th gear and the reverse gear are shifted via the multi-plate clutch K1. The 2nd, 4th and 6th gear are shifted via the multi-plate clutch K2. In principle one partial gearbox is always actuated and in the other partial gearbox the next gear is already shifted, but the clutch for this gear is still open. A conventional synchronization and gearshift unit of a gearbox is assigned to each gear.Principle representationProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Partial gearbox 2Multi-plate clutch K2Engine torqueSP56_13Partial gearbox 1Multi-plate clutch K112GB Torque inputThe torque reaches from the crankshaft to the two-mass flywheel. The plug serration of the two-mass flywheel on the input hub of the multi-plate clutch transfers the torque to the drive plate of the multi-plate clutch. This is connected by the outer plate carrier of the clutch K1 with the main hub of the multiplate clutch. The outer plate carrier of the clutch K2 is also powerfully connected with the main hub.Outer plate carrier K2Outer plate carrier K1Two-mass flywheelInput hubDrive plateSP56_14Main hubGBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�13 Structure of DSGMulti-plate clutchesThe torque is inserted into the respective clutch through the outer plate carrier. By closing the clutch, the torque is passed on to the inner plate carrier and then to the appropriate drive shaft. Always one multi-plate clutch is actuated.Multi-plate clutch K1 The clutch K1 is a multi-plate clutch. It is the outer clutch and transfers the torque to the drive shaft 1 for the 1st 3rd, 5th gear and the reverse gear. For closing the clutch, the oil is pressed into the oil pressure chamber of the clutch K1. Thus the piston 1 shifts and presses the plate package of the clutch K1 together. The torque will be transfered via the plate package of the inner plate carrier to the drive shaft 1. When opening the clutch, the disc spring presses the piston 1 again back into the initial position.Inner plate carrier K1 Piston 1Outer plate carrier K1Clutch K1Oil pressure chamber K1Drive shaft 1Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Disc springSP56_1514GB Multi-plate clutch K2 The clutch K2 is a multi-plate clutch. It is the inner clutch and transfers the torque to the drive shaft 2 for the 2nd, 4th and 6th gear. For closing the clutch, the oil is pressed into the oil pressure chamber K2. The piston K2 closes thereupon the power flux via the plate package to the drive shaft 2. The helical springs press the piston 2 back into the initial position when opening the clutch.Outer plate carrier 2 Piston 2Clutch K2Inner plate carrier K2Oil pressure chamber K2 Helical springDrive shaft 2Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� SP56_16GB15 Structure of DSGDrive shaftsThe torque of the engine is passed on from the multi-plate clutch K1 or K2 to the relevant drive shaft.Drive shaft 1Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_17Drive shaft 2Drive shaft 2 The drive shaft 2 is illustrated through the fitting position of the drive shaft 1.Pulse rotorThe drive shaft 2 is hollow drilled and connected through a plug serration to the multi-plate clutch K2. The helical gearings for the 6th, 4th and 2nd gear are seated on the drive shaft 2. A common gear is used for the 6th and 4th gear.2nd gearA pulse rotor for the rpm drive shaft sender 2 G502 is located next to the gear for the 2nd gear, in order to detect the speed of this drive shaft.6th/4th gearSP56_1816GB Drive shaft 1Pulse rotorSP56_195th gear1st/reverse gear3rd gearA pulse rotor for the rpm drive shaft sender 1 The drive shaft 1 operates through the hollow G501 is located between the gear for 1st/ drilled drive shaft 2. It is connected through a plug serration to the multi-plate clutch K1. reverse gear and the 3rd gear, in order to The helical gearings for the 5th gear, the detect the speed of this drive shaft. by copyright. common gear for the 1st and the Protected reverse gear Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability as well as the 3rd gear are seated on drive with the respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� shaft 1.Note: A stronger solenoid can destroy the pulse rotor!GB17 Structure of DSGDrive shaftsAccording to the two drive shafts there are also two output shafts in the automatic gearbox DSG. By means of the common use of the gears for the 1st gear and the reverse gear as well as for the 4th and 6th gear on the drive shafts the overall length of the gearbox could be minimized.Drive shaft 1stretched illustration1st gear3rd gear4th gear2nd gearOutput gear pinionFitting position in the gearbox Drive shaftsSliding sleeveSP56_20 SP56_21On the output shaft 1 are – the triple synchronized sliding gears for the 1st, 2nd and 3rd gear – the simple synchronized sliding gear for the 4th gear and – the output gear pinion for engaging into the differential gear. The output shaft grips into the gear pinion for the final drive of the differential gear.18Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB Drive shaft 2stretched illustrationFitting position in the gearboxProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_22 SP56_23Pulse rotor for G195 and G1966th gear 5th gearReverse gearOutput gear pinionOn the output shaft 2 are – – – a pulse rotor for the gearbox output speed the gearshifts of the 5th, 6th gear and the gear of the reverse gear the output gear pinion for engaging into the differential gear.Both output shafts pass on the torque via their output gear pinion to the differential gear.GB19 Structure of DSGReverse shaftThe reverse shaft changes the direction of rotation of the output shaft 2 and therefore also the one of the gear pinion for the final drive of the differential gear. It comes with the common gear for the 1st gear and the reverse gear on the drive shaft 1 and with the sliding gear for the reverse gear on the output shaft 2.Stretched illustrationFitting position in the gearboxProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_24 SP56_25Gear for 1st and reverse gearReverse shaft20GB Differential gearBoth output shafts are in constant contact with the drive wheel of the differential gear and thus transfer the torque. The differential gear transfers the torque via the drive shafts onto the wheels. The parking gear is integrated into the differential gear.Stretched illustrationFitting position in the gearboxSP56_27SP56_26Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Drive gear of differential gearParking gearGB21 Structure of DSGParking positionFor safe stationary positioning of the vehicle and against inadvertent moving off when the hand-brake is not applied, a parking position is integrated into the axle differential gear. The insertion of the catch is performed purely mechanically via a control cable between the selector lever and the lever for the parking position at the gearbox. The control cable is used exclusively for operating the parking position.CatchParking gearSP56_28Control cable for selector leverIt functions as follows:LeverBy moving the selector lever into the position „P“, the parking position is engaged. Thus, the catch grips into the teeth of the parking gear. The latch spring locks into the lever and fixes the catch in its position.Slide valvePressure spring 1SP56_29If the catch touches a tooth of the parking Latch spring gear, the pressure spring 1 is tensioned. If the vehicle moves, the catch is pressed by Protected copyright. Copying is not gear permitted Parking the relaxing pressure spring 1by into the nextfor private or commercial purposes, in part or in whole, unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability gap of the parking gear. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Pressure By operating the selector lever from the position „P“, the parking position is released. The slide valve is pushed back into the initial position to the right and the pressure spring 2 presses the catch out of the gap of the parking gear.spring 2Catch22GB SynchronizationFor engaging a gear, the shift collar must be pushed onto the shift serration of the sliding gear. It is the task of the synchronization to establish synchronization between the gears to be shifted and the shift collar. Basis of the synchronization are molybdenumcoated brass synchronizers. The 1st, 2nd and 3rd gear are equipped with a triple synchronization. In relation to a single synchronization with only one friction cone, a clearly increased friction surface is available. The synchronization power increases, because a larger heat transfer surface is present. The adjustment of the large differences in rpm between the different sliding gears in the lower gears takes place faster. Engaging the gears can take place with less forces. The 4th, 5th and 6th gear have a single synchronization. Here the differences in rpm are not so great when shifting. Therefore the rpm adjustment takes place faster. No demanding effort for the synchronization is needed.The reverse gear has a double cone synchronization.The triple syncronization consists of – – – – an outer ring (1st synchronizer ring), an intermediate ring, an inner ring (2nd synchronizer ring) and the friction cone on the sliding gear/gear.The single syncronization consists of – – the synchronizer ring and the friction cone of the sliding gear/gear.Intermediate ring Inner ring Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_30SP56_31Outer ringFriction coneSynchronizer ringFriction coneGB23 Structure of DSGTorque transfer in the vehicleThe torque of the engine will be transferred via the two-mass flywheel onto the automatic gearbox DSG. For the front final drive, the drive shafts transfer the torque to the front wheels. For vehicles of other company brands with allwheel drive, the torque is passed on via an additional angle gearbox and a propshaft to the rear axle. The propshaft transfers the torque to the Haldex coupling. A differential gear for the rear axle is integrated into the rear final drive.Automatic gearbox DSGDifferential gearAngle gearboxHaldex couplingSP56_32Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Rear axle drive with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_33Rear axle differential gear24GB Power flow in the gearsThe torque transmission in the gearbox takes place either on the outer clutch K1 or on the inner clutch K2. Each clutch drives one drive shaft. The drive shaft 1 (inner) is driven by the clutch K1 and the drive shaft 2 (outer) by the clutch K2. The passing on of the power transmission to the differential gear is performed by – – the output shaft 1 for the 1st, 2nd, 3rd, 4th gear and the output shaft 2 for the 5th, 6th gear and the reverse gear.1st gear Clutch K1 Drive shaft 1 Drive shaft 1 Differential gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_34Note: For improved understanding, the illustration of the power flow is performed schematically in a "stretched" illustration.GB25 Structure of DSG2nd gear Clutch K2 Drive shaft 2 Drive shaft 1 Differential gearSP56_353rd gear Clutch K1 Drive shaft 1 Drive shaft 1 Differential gearSP56_364th gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Clutch K2 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Drive Copyright shaft 2by ŠKODA AUTO A. S.�Drive shaft 1 Differential gearSP56_3726GB 5th gear Clutch K1 Drive shaft 1 Drive shaft 2 Differential gearSP56_386th gear Clutch K2 Drive shaft 2 Drive shaft 2 Differential gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_39Reverse gear Clutch K1 Drive shaft 1 Reverse shaft Drive shaft 2 Differential gearThe change of the direction of rotation for the reverse gear is performed via the reverse shaft.SP56_40GB27 Mechatronic moduleMechatronicsThe mechatronics is accommodated in the gearbox, rinsed around with DSG oil. It consists of an electronic control unit and an electrohydraulical control unit. The mechatronics is the central control unit of the gearbox. All sensor signals and all signals of other control units run together in it and all actions are introduced and supervised by it. There are twelve sensors in this compact unit. Only two sensors are assigned outside the mechatronics. It controls or regulates hydraulically eight gear actuators via six pressure modulation valves and five switch valves as well as the pressure and the cooling oil flow of both clutches. The control unit of the mechatronics learns (adapted) the positions of the clutches, the positions of the gear actuators with engaged gear and the main pressure.Central plug for vehicleElectrohydraulic control unitProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_41 SP56_4228GB The advantages of this compact unit are: – – – The biggest part of the sensors is integrated. The electrical actuators are located directly at the mechatronics. Necessary electrical interfaces on vehicle side are performed by a central plug.In addition, it means highest thermal and mechanical stresses for the control unit. Possible temperatures from –40 °C to +150 °C as well as occuring mechanical oscillations up to 33gn must not impair the driveability. gn = Standard acceleration gn = 9.806 65 m/s2 In technical calculations usually sufficient approximate value 9.81 m/s2.This measure reduces the number of plug connections and wiring. That means a larger electrical reliability and a lower weight.Electronic control unitProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_43GB29 Electrohydraulic control unitElectrohydraulic control unitThe electrohydraulical control unit is integrated in the mechatronic module. In the control unit there are all solenoid valves, pressure control valves as well as the hydraulic slide valves and the multiplexer (multiplier). N88 N89 N90 N91 N92 N215 - Solenoid valve 1 - Solenoid valve 2 - Solenoid valve 3 - Solenoid valve 4 - Solenoid valve 5 - Pressure control valve 1 for autom. gearbox N216 - Pressure control valve 2 for autom. gearbox (gear actuator valve) (gear actuator valve) (gear actuator valve) (gear actuator valve) (multiplexer valve) In addition, there is a pressure relief valve on the hydraulic module. It prevents inadmissible increase of pressure to values, which could lead to damage on the hydraulic slide valve. N217 - Pressure control valve 3 for autom. gearbox (main pressure valve) N218 - Pressure control valve 4 for autom. gearbox (cooling oil valve) N233 - Pressure control valve 5 for autom. gearbox (safety valve 1) N371 - Pressure control valve 6 for autom. gearbox (safety valve 2) A - Pressure relief valve B - Conductor plate(clutch valve K1)(clutch valve K2)N216N217AN215N92N218Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�N371BN88N233SP56_4430GB They have different shift characteristics depending upon the function of the valves. It is differentiated between – – ,,Yes/No“ switching valves and Modulation valves.To the „Yes/No“ switching valves belong – – the gear actuator valves and the multiplexer valve.To the modulation valves belong – – – – the main pressure valve the cooling oil valve the clutch valves and the safety valves.After removing the conductor plate the valves N89, N90 and N91 for the gear actuator are visible.N92 N89Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted N90 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�N91SP56_45GB31 Oil circulationOil circulationThe DSG has a common oil circulation system for all gearbox functions. Altogether there is in this circulation system 7.2 l direct shift gearbox oil (DSG oil). The oil must comply to the following requirements: – – – – Safety of the clutch regulation and the hydraulic control Stable viscosity in the entire temperature range Resisting high mechanical stresses No permissible foaming The tasks of this oil are: – Lubrication/cooling • of the multiple clutch, • the wheels, shafts, bearings and • the synchronization Actuation • of the multiple clutch and, • the gear actuator piston–The oil cooler through which the engine coolant flows, prevents that the oil temperature increases above 135 °C.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Oil coolerPressure oil filter Gear actuatorOil spray pipe for cooling of the gear wheelsSP56_46Slide valve bodyOil pumpOil sump32GB Oil pumpSafetyA safety cell pump suctions the DSG oil and produces the oil pressure, which is necessary for the operation of the hydraulic components. It enables a maximum output of 100 l/min. and a main pressure of 2 MPa. The oil pump supplies – – – – the multi-plate clutches, the clutch cooling, the shift hydraulics and the gear pinion lubrication.Delivery sideThe drive of the oil pump is performed via the pump shaft running at engine speed. This pump shaft is the third shaft within both drive shafts 1 and 2 inserted into one another.SP56_47Suction sideReturn flow to suction sideTwo-mass flywheel Pump shaftProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Oil pumpDrive shaft 1Drive shaft 2SP56_48GB33 Oil circulationOil circulation system diagramPressure relief valve Oil pump Main pressure slide valve Pressure control valve 3 (main pressure valve)Oil cooler Return flow to oil pump Suction filter Clutch cooling oil slide valveCooling oil to the clutches Pressure oil filter Oil spray pipe Lubrication/cooling of gear wheelsOil sump for multi-plate clutch K2for multi-plate clutch K1SP56_49Gear actuator Colour legend Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information controlled pressure, workin this document. Copyright by ŠKODA AUTO A. S.�pressure, main pressure uncontrolled pressureReturn flow in the oil sumpcontrolled pressure, clutch cooling34GB Description of the oil circulation system The oil pump suctions the oil via the suction filter from the oil sump and delivers it under pressure to the main pressure slide valve. The main pressure slide valve is controlled by the pressure control valve 3 - the main pressure control valve -. The main pressure valve regulates the work pressure in the automatic gearbox DSG. Under the main pressure slide valve, an oil channel returns to the suction side of the pump. The other oil channel is divided. A channel leads to the oil cooler and then via the pressure oil filter back into the oil sump. The other channel leads the oil flow to the clutch cooling oil slide valve. The work pressure regulated by the pressure control valve 3 is used by the gearbox for the operation of the multi-plate clutches and for shifting the gears. The oil cooler is integrated into the cooling circuit of the engine. The pressure oil filter is located outside the gearbox housing. The pressure relief valve ensures that the oil pressure does not rise above 3.2 MPa. The oil reaches the gear wheels directly through the oil spray pipe.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB35 Oil circulationHydraulic elements in the oil circulation systemPressure relief valve Main pressure slide valve Pressure control valve 3 (main pressure valve)Pressure accumulator Safety valve N233 and N371 Pressure accumulator Hydraulic pressure sender G193 for K1Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Non-returnwith valve respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Non-return valve Hydraulic pressure sender G194for K2Clutch valve N216 Multiplexer valve N92Clutch valve N215N88N89N90N91MultiplexerSP56_50Gear actuator Colour legend controlled pressure, work pressure, main pressure uncontrolled pressure Return flow in the oil sump36GB Electrohydraulic control of the oil circulation system Pressure valve 3 for automatic gearbox N217 (main pressure valve) It is actuated by the electronic control unit and controls the main pressure slide valve. Thus, the work pressure in the hydraulic system of the automatic gearbox DSG is regulated. Through the main pressure valve the oil currents for – – the oil return flow through the oil cooler/ pressure filter/oil spray pipe and the return flow to the oil pump Safety valves One safety valve each for clutch K1 (N233) and clutch K2 (N371) enables a fast opening for the respective clutch. This is necessary, if their actual clutch pressure is above the specified value. Hydraulic pressure sender G193 and G194 The hydraulic pressure senders G193 and G194 control the clutch pressure of the clutches K1 and K2. A pressure relief valve prevents a too strong increase of the operating pressure on a defective main pressure slide valve.are actuated. The work pressure opens the two clutch valves N215 and N216 and closes the clutches K1 and K2 and the four gear actuator valves N88, N89, N90 and N91 for engaging the gears. Multiplexer valve N92 It operates the multiplexer. The multiplexer (multiplier) enables the controlling of the eight gear actuator cylinders with only four solenoid Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted valves. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The multiplexer is pressed through a spring into its basic position. In the basic position, the 1st, 3rd, 6th gear and reverse gear can be shifted. If the multiplexer valve N92 is energized, oil pressure reaches the multiplexer and it is pressed against the spring force into the work position. The 2nd, 4th, 5th and neutral gear can be shifted.GB37 Oil circulationClutch cooling oil system The temperature of the multiple clutch increases through the mechanical friction in the multi-plate clutches. The multi-plate clutches must be cooled down so that this does not overheat. There is a separate clutch cooling oil circulation system within the oil circulation system for the cooling of the clutches. A cooling oil slide valve and pressure control valve 4 N218 (clutch cooling oil valve) belong to the cooling oil circulation system.Clutch cooling oil slide valvePressure accumulator Oil temperature sender in multi-plate clutchSP56_51MechatronicsIt functions as follows: The oil temperature sender in multi-plate The pressure control valve increases or Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. measured does not guarantee or accept any liability clutch G509 measures the oil temperature reduces, depending on the with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� temperature, the oil pressure on the clutch directly at the oil leakage of the multi-plate clutches. cooling oil slide valve. The cooling oil slide valve opens or closes the oil channel to the multi-plate clutches Depending on the measured temperature, the depending on the oil pressure. control unit actuates the pressure control valve. The maximum cooling oil quantiy is 20 ltr./per minute. The maximum cooling oil pressure is 0.2 MPa.38GB Shifting the gears Shifting the gears is performed by shift forks in the same way as on conventional manual gearboxes. 2 gears are shifted by each shift fork. The actuation of the shift forks is performed on the automatic gearbox DSG hydraulically and not through the shifts rods as on the conventional manual gearbox. The shift forks run on ball bearings in one cylinder. For shifting, oil is lead from the mechantroncis into the left cylinder. Since the right cylinder is pressureless, the shift fork shifts and operates the sliding sleeve. Thus, the gear is engaged. If the gear is engaged, the shift fork is shifted pressureless. The gears maintain the shift serration and the catch mechanism on the shift fork through the after-body. If the shift fork is not actuated, it is held by a catch mechanism in the neutral position, arranged in the gearbox housing. On each shift fork is a permanent magnet. The Shift fork path sensors detects through the permanent Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted magnets the exact position of the individual unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� shift forks in the mechatronics.Piston Oil pressure of the mechantronics Catch houseSP56_52CylinderMagnet for path sensorSP56_53Sliding sleeveGB39 System overviewSensorsMechatronics for direct manual gearbox J743 Gearbox oil temperature sender in multi-plate clutch G509 Gearbox input r.p.m. sender G182Gearbox output r.p.m. sender G192 and gearbox input r.p.m. sender 2 G196 R.p.m drive shaft sender 1 G501 and r.p.m drive shaft sender 2 G502Hydraulic pressure sender 1 for automatic gearbox G193 and hydraulic pressure sender 2 for automatic gearbox G194Gearbox oil temperature sender G93 Temperature sender in the control unit G510Path sensor 1 to 4 for gear actuator G487, G488, G489, G490Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�40GB ActuatorsCANSelector lever sensor control unit J587Selector lever lock solenoid N110Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Pressure control valves 1 to 3 N215, N216, N217Solenoid valves 1 to 5 N88, N89, N90, N91, N92 and pressure control valves 4 to 6 N218, N233, N371SP56_54Diagnostic connectionGB41 SensorsGearbox input r.p.m. sender G182 The gearbox input rpm sender is inserted into the gearbox housing. It scans electronically the exterior of the multiple clutch and detects the gearbox input rpm. The gearbox input rpm sender is identical to the engine speed. The rpm sender functions according to the Hall principle. Sender G509 is also located in the housing of this sender. Both senders are connected via electrical lines to the mechatronics.SP56_55G182Use of signal The signal of the gearbox input r.p.m is a value for the calculation of the slip of the multi-plate clutches. For this calculation the control unit still needs the signals of the sender G501 and G502. Based on the clutch slip, the control unit can actuate more accurately the opening and closing of the clutches.Effects of signal failure In case of failure of the signal, the control unit uses the engine speed of CAN as replacement signal.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�42GB R.p.m drive shaft sender 1 G501 and r.p.m drive shaft sender 2 G502 Both senders are located on the mechatronics. The sender 1 G501 detects the speed of the drive shaft 1. The sender 2 G502 detects the speed of the drive shaft 2. Both senders are Hall senders. For the detection of the rpm, each sender touches a pulse rotor on its shaft. The pulse rotor consists of a panel. A rubber metal layer is applied onto this panel. This layer forms circulating small magnets with north and south pole. There is an air gap between the individual magnets.G501G502SP56_76Pulse rotor for G501SP56_56SP56_57Pulse rotor for G502Use of signal In combination with the signal of the gearbox input rpm, the control unit calculates the output speeds of the multi-plate clutches K1 and K2 and detects the slip of the clutches. On the basis of the slip, the control unit recognizes the opening and the closing condition of the clutches. Furthermore, the signal is used as a check of the shifted gear. In combination with the signals of the gearbox input rpm sender, the control unit detects whether the correct gear is shifted.Effects of signal failure If one of the signals fails, then the related gearbox area is switched off. If the sender G501 fails, it can only be driven in the 2nd gear. If the sender G502 fails, it can only be driven in the 1st and 3rd gear.Note:Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted The pulse rotors must not unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� stored close to powerfulbemagnets.GB43 SensorsGearbox output r.p.m. sender G195 and gearbox input r.p.m. sender 2 G196 Both senders are located on the mechantronics and are inseparably connected to the control unit. They are Hall senders as all the other speed senders in this gearbox. They touch both the same pulse rotor on the output shaft 2. Both senders are accomodated offset against each other in one housing. This results in two signals offset against each other. If the signal of the sender G195 is „high“, then the signal of the sender G196 is still „low“.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�G195G196 Pulse rotorSP56_58SP56_59G196G195Use of signal Based on the detailed signals, the control unit detects the driving speed and the driving direction. The driving direction is detected by the signals which are offset against each other. During a change of direction, the signals arrive in reverse order in the control unit.Effects of signal failure In case of failure of the signals, the control unit uses the driving speed and the direction of travel signal of the ABS control unit.44GB Hydraulic pressure sender 1 for automatic gearbox G193 and hydraulic pressure sender 2 for automatic gearbox G194 Both hydraulic pressure senders are located in the electrohydraulical control unit of the mechatronics. The same pressure is exerted on the hydraulic sender 1 G193 as on the multi-plate clutch K1. The pressure of the multi-plate clutch K2 is exerted on the hydraulic sender 2 G194.G193 G194SP56_60Function of the hydraulic pressure sender The hydraulic pressure sender consists of a pair of parallel, electrical conducting plates. The upper plate is fastened to a ceramic diaphragm, which bends according to the pressure changes. The other plate is rigidly connected with a ceramic substrate. This does not react to pressure changes. As soon as the pressure changes, the diaphragm bends and therefore also the upper plate. The distance between the plates changes. Thus, a reliable signal as a function of the oil pressure is produced.Use of signalEffects of signal failureOn the basis of these signals, the electronic If a pressure signal fails or if no pressure is control unit of the mechatronics detects the built up, the appropriate branch of gearbox is hydraulic pressure, which affects the switched off. respective multi-plate clutch. The vehicle can only be driven in the 1st and/ The control unit needs the accurate hydraulic or 3rd gear or in 2nd gear. pressure for the regulation of the multi-plate Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability clutch.with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�DSG oil pressureParallel platesCeramic diaphragmsSP56_61SP56_62SubstrateGB45 SensorsGearbox oil temperature sender in multi-plate clutch G509 The sender G509 is located in the housing of the gearbox input rpm sender G182. It measures the temperature of the DSG oil flowing out of the multi-plate clutches. As the oil in the multi-plate clutches is strongly thermally stressed, it has at this point the highest temperature in the gearbox. This sender is designed in such a way that it can measure the temperatures very fast and accurately. It functions in the temperature range from –55 °C to +180 °C.SP56_63G509Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Use of signal According to the signals of the oil temperature sender G509, the control unit controls the clutch cooling oil quantity and introduces further measures for the protection of the gearbox.Effects of signal failure In case of signal failure, the control unit takes the signals of the sender G93 and G510 as replacement signal.46GB Gearbox oil temperature sender G93 and temperature sender in the control unit G510 Both senders are assigned directly to the mechatronics. The mechatronics is constantly rinsed by the DSG oil and thereby warmed up. Strong heating can impair the functions of the electronics. Both senders measure the temperature directly in the endangered components. Thus, oil temperature lowering measures can be introduced early and a too strong heating of the mechatronics can be avoided.G93G510SP56_64Use of signal The signals of both senders are used for checking the mechatronics temperature. In addition, a warm-up switching program is started based on the sender signals. Both senders mutually check each other.Effects of signal failure For gearbox oil temperatures as of 138 °C the mechatronics arranges a reduction of the engine torque. For temperatures over 145 °C the multi-plate clutches are no longer supplied with oil pressure and they open.GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�47 SensorsPath sensors 1 to 4 G487, G488, G489, G490 for gear actuator The path sensors are located in the mechatroncis. They are Hall senders. In combination with the solenoids at the shift forks they generate a signal, from which the control unit detects the positions of the gear actuators. Each path sensor supervises the position of a gear actuator /shift fork, with which can be selected between two gears – – – – G487 for the 1st/3rd gear, G488 for the 2nd/4th gear, G489 for the 6th/Reverse gear and G490 for the 5th/Neutral gear.G487G488Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO Magnet A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability for with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�path sensorSP56_65G490G489SP56_66Use of signal On the basis of the exact position, the control unit pressurizes the gear actuators for shifting the gears with oil pressure.Effects of signal failure If a path sensor signal fails, the related gearbox area is switched off. The gears of the related gearbox area can no longer be driven.48GB Selector lever sensor control unit J587 The selector lever sensor control unit is integrated into the selector lever. It functions simultaneously as a control unit and as a sensor. The control of the selector lever lock solenoids is performed via the control unit. The selector lever scale lighting is integrated into the cover. At the same time the hall senders for detecting the selector lever position and the hall senders for Tiptronic detection are accommodated in it. The signals of the selector lever position and the signals of the Tiptronic are transmitted via the CAN bus to the mechatronics and to the control unit for dash panel insert.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Hall sender for Tiptronic positionSelector lever sensor control unit J587SP56_67Hall senderGB49 ActuatorsPressure valve 3 for automatic gearbox N217 (main pressure valve) The pressure control valve 3 for automatic gearbox is located in the electrohydraulical control unit of the mechatronics. It is a modulation valve. The main pressure in the hydraulic system of the mechatronics is regulated by this valve. The main factor for the calculation of the main pressure is the current clutch pressure, which is dependent on the engine torque. The engine temperature and the engine speed are used for the correction of the main pressure. The control unit constantly adapts the main pressure to the current situation.N217SP56_68Effects of failure If the pressure valve fails, the maximum main pressure is used. Thus, the fuel consumption can increase and when shifting noises can occur.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�50GB Pressure control valve 1 for automatic gearbox N215 and pressure control valve 2 for automatic gearbox N216 (clutch valves) The pressure control valves N215 and N216 are mounted in the electrohydraulical control unit of the mechatronics. They are modulation valves and generate the control pressure for the multi-plate clutches the pressure control valve 1 N215 for the multi-plate clutch K1 and the pressure control valve 2 N216 for the multi-plate clutch K2.N216Basis for the calculation of the clutch pressure is the current engine torque. The control unit adapts the clutch pressure to the current friction value of the multi-plate clutches.N215Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP56_69Effects of failure If a pressure control valve signal fails, the related gearbox area is switched off. This fault is indicated in the dash panel insert.GB51 ActuatorsPressure control valve 4 N218 (cooling oil valve) The pressure control valve N218 is located in the electrohydraulical control unit. It is a modulation valve and controls the clutch cooling oil quantity via a hydraulic slide valve. The control unit uses the signal of the oil temperature sender in the multi-plate clutch G509 to control the valve.N218SP56_70Effects of failure If the pressure control valve cannot be actuated, the maximum cooling oil quantity flows through the multi-plate clutches. At low outside temperatures it can lead to problems when shifting the gears and to an increased fuel consumption.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�52GB Solenoid valves 1 N88, 2 N89, 3 N90 and 4 N91 (gear actuator valves) All four solenoid valves are located in the electrohydraulical control unit of the mechatronics. They are "Yes/No" valves. They control all oil pressures via the multiplexer slide valve to the gear actuators. If de-energized, the solenoid valves are closed, no oil pressure reaches the gear actuators. • Solenoid valve 1 N88 controls the oil pressure for shifting the 1st and 5th gear. • Solenoid valve 2 N89 controls the oil pressure for shifting the 3rd and the neutral gear. • Solenoid valve 3 N90 controls the oil pressure for shifting the 2nd and the 6th gear. • Solenoid valve 4 N91 controls the oil pressure for shifting the 4th and the reverse gear.N90N91 N89N88SP56_71Effects of failure If a solenoid valve fails, the corresponding gearbox branch, in which the gear actuator is located, is switched off. The vehicle can only be driven in the 1st and/ or 3rd or in the 2nd gear.GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 53 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� ActuatorsSolenoid valve 5 N92 (multiplexer valve) The solenoid valve 5 N92 is located in the electrohydraulical control unit of the mechatronics. It controls the multiplexer in the hydraulical control unit. If the solenoid valve is actuated, the 2nd, 4th and 6th gear are shifted. If the solenoid valve is de-energized, the 1st and/or 3rd or 5th and reverse gear can be shifted.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�N92SP56_72Effects of failure If the multiplexer valve fails, it remains deenergized in the basic position. It can no longer be actuated by the oil pressure. False gears can be shifted. The standing still of the vehicle is also possible.54GB Pressure control valve 5 N233 and pressure control valve 6 N371 (safety valves) The pressure control valves N233 and N371 are accommodated in the hydraulic module of the mechatronics. They are modulation valves. They control the safety slide valve in the slide valve of the mechatronics. The safety slide valves shift the respective gearbox area hydraulically pressureless in the case of a safety-relevant error in the gearbox branch. The pressure control valve 5 N233 controls the safety slide valve in the 1st gearbox branch. The pressure control valve 6 N371 controls the safety slide valve in the 2nd gearbox branch.N371N233SP56_73Effects of failureIf a pressure control valve fails, there can no longer be any gear shifted into the corresponding gearbox branch. If the gearbox area 1 fails, it can only be driven in the 2nd gear. If the gearbox area 2 fails, it can only be driven in the 1st or 3rd gear.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB55 Function diagramComponents A E313 F319 G93 G182 G193 G194 G195 G196 G487 G488 G489 G490 G501 G502 G509 G510 J… J329 J519 J527 J587 J743 L101 N88 N89 N90 N91 N92 N110 N215 N216 N217 N218 N233 N371 S… Battery Selector lever Selector lever switch locked in P Gearbox oil temperature sender Gearbox input rpm sender Hydraulic pressure sender 1 for automatic gearbox Hydraulic pressure sender 2 for automatic gearbox Gearbox output rpm sender Gearbox output rpm 2 sender Path sensor 1 for gear actuator Path sensor 2 for gear actuator Path sensor 3 for gear actuator Path sensor 4 for gear actuator R.P.M drive shaft sender 1 R.P.M drive shaft sender 2 Oil temperature sender in multi-plate clutch Temperature sender in the control unitAJ329N88 N89Engine control unit Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Voltage supply relay of terminal 15 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Onboard supply control unit S Steering column electronics control unit Selector lever sensor control unit Direct shift gearbox mechatronics Lamp for selector lever scale lighting Solenoid valve 1 Solenoid valve 2 Solenoid valve 3 Solenoid valve 4 Solenoid valve 5 Selector lever lock solenoid Pressure control valve 1 for automatic gearbox Pressure control valve 2 for automatic gearbox Pressure control valve 3 for automatic gearbox Pressure control valve 4 for automatic gearbox Pressure control valve 5 for automatic gearbox Pressure control valve 6 for automatic gearbox Fuse+30 a +15 vT20e / 11T20e / 1831inouta - Terminal 30 B - CANCAN bus drive high C - CAN bus drive low56GBT20e / 13 J519xyG487G489G93G195G501N90 N91N92N215N216N217N218 J743N233N371G193T20e / 19 T20e / 16 T20e / 17G194T4z / 4 T4z / 1 T4z / 2 T4z / 3G488G490G510T20e / 1G196T20e / 10G502T20e / 15xyva J527G509 G182 J587 E313L101N110F319 J... J... B J... C 31SP56_74Input signalCAN busOutput signalProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Bidirectional unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Supply voltageDiagnostic connectionEarthGB57 CAN databus linkageCAN databus linkageThe pattern represented below shows symbolically the integration of the mechatronics for direct shift gearbox into the CAN databus structure of the vehicle. J104 - ABS control unit with EDL J248 - Diesel direct injection system control unit J285 - Dash panel insert control unit J519 - Onboard supply control unit J527 - Steering column electronics control unit J533 - Databus diagnostic interface J587 - Selector lever sensor control unit J623 - Engine control unit J743 - Direct shift gearbox me