TECHNICAL DOCUMENTATION

SSP 057 2,0 ltr 103 kW or 100 kW TDI Unit Injector Engine

PDFEN42 pages5 MB
SSP 057 2,0 ltr 103 kW or 100 kW TDI Unit Injector Engine - PDF cover

This PDF is currently unavailable.

Read document text
The times are long past, where diesel engines were slow acting, woke up the whole neighbourhood during morning start-up, and black smoke was trailing out of the exhaust when driving at full speed. The driving performance, dynamics as well as vehicle comfort, economy and emissions have been significantly improved through further development of all engine components, combustion procedure, materials and machining procedure as well as the injection pressures. In order to comply with strict exhaust gas emission regulations and to lower the fuel consumption at a high performance, Škoda Auto a. s. relies on the TDI Engine generation with 4-valve technology.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�2GB ContentsIntroduction 4Engine mechanical components Cylinder head Supporting frame 4-valve technology Roller rocker arm Valve seat rings Piston Toothed belt drive Tandem pump Unit injector6 6 7 8 10 11 12 14 15 17Engine management System overview Control unit at CAN data bus Engine speed sender Hall sender G40 Clutch position sender G476 Accelerator pedal position sender G79 and G185 Exhaust gas recirculation system Glow plug system20 20 22 23 24 26 28 33 36Function diagram40Notes42ServiceOCTAVIA IIII OCTAVIAXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIServiceOCTAVIA IIXXXXXXXXXXXXXXXX XXXXXXXServiceOCTAVIA IIXXXXXXXXXXXXXXXXXXXXXX XXXXXXXS e r v i c eYou will find notes on inspection and maintenance, setting and repair instructions in the Workshop Manual.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXGB3 Introduction2.0 ltr./103 kW or 100 kW* TDI Unit Injector Engine with 4-valve technologyProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP57_01The 2.0 ltr./103 kW or 100 kW* TDI Engine is the first representative of the new generation of TDI Engines with 4-valve technology from VOLKSWAGEN. A 100 kW version of the engine has already been fitted in the Volkswagen Touran. It has been developed from the 1.9 ltr./96 kW TDI Engine. The enlargement of the displacement in comparison to the basic engine was achieved by increasing the size of the cylinder bore.The new 2.0 ltr/103 kW or 100 kW* TDI Engine has a newly developed crossflow aluminium cylinder head with two inlet and two exhaust valves per cylinder. Other technical highlights are: • switchable radiator for exhaust gas recirculation, • crankshaft sealing flange with integrated sensor rotor for engine speed, • new glow plug system.*The 2.0 ltr./100 kW TDI Engine is only intended for the Belgium market.GB4 Technical Data Engine code letters Design Displacement Bore Stroke Compression ratio Valves per cylinder Firing order max. power output max. torque Engine management Fuel Exhaust after treatment Emission standard Power output/torque diagram 2.0 ltr./103 kW TDI – BKD100 360 100BKD 4-cylinder inline engine 1968 cm3 81 mm 95.5 mm 18.5 : 1 4 1–3–4–2 103 kW at 4000 rpm 320 Nm at 1750 to 2500 rpmAZV100 kW at 4000 rpm 320 Nm at 1750 to 2500 rpmBosch EDC 16 with Unit injection system Exhaust gas recirculation, Oxidation catalytic converter EU4Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Diesel at least 49 CZ2.0 ltr./100 kW TDI – AZV3608032080320702807028060 P (kW)240 M (Nm) P (kW)60240 M (Nm)50200502004016040160301203012020802080SP57_020 1000 2000 3000 4000 5000 6000 0 1000 2000 3000 4000 5000 6000 n (min–1 ) n (min–1 )SP57_79M = Torque; n = Engine speed; P = Power outputAt a speed between 1750 rpm and 2500 rpm the 2.0 ltr./103 kW TDI Engine has a torque of 320 Nm. It reaches its maximum power output of 103 kW at a speed of 4000 rpm.At a speed between 1750 rpm and 2500 rpm the 2.0 ltr./100 kW TDI Engine has a torque of 320 Nm. It reaches its maximum power output of 100 kW at a speed of 4000 rpm.5GB Engine mechanical componentsCylinder headvertically positioned, centrally mounted unit injector Valve lever for unit injector Valve-lever shaftInlet camshaftExhaust camshaftSP57_03Inlet duct Full floating axle Roller rocker arm for valvesOutlet ductProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Valves in vertical positionThe cylinder head of the 2.0 ltr. TDI Engine is a crossflow aluminium cylinder head with two inlet and exhaust valves per cylinder. The valves are positioned vertically. The two overhead camshafts (D-OHC) are driven together via a toothed belt.The exhaust camshaft ensures besides the exhaust valve control also the drive of the unit injectors. The inlet camshaft ensures besides the control of the inlet valves also the drive of the tandem pump. The valve actuation is performed via the roller rocker arms, which are located on the full floating axles.6GB Supporting frameThe supporting frame is a compact pressure casting out of aluminium. It takes over the following functions: • Mounting of the camshafts • Mounting and guidance of the valve-lever shaft for the drive of the unit injectors • Location of the central plug for the current supply • Location of the cable duct for the unit injectors and glow plugs.SP57_04Crossbar Axle mounting of inlet camshaft Cable ductSP57_05The whole structure of the supporting frame with its triple force crossbars reinforces not only the cylinder head but also clearly improves the acoustics of the engine.Axle mounting of exhaust camshaft Central plugBearing support of the valve-lever shaftProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Supporting frameScrewed connection concept “Screw in Screw”Cylinder headCylinder head boltThe supporting frame is directly bolted with both inner rows of bolts into the bolt heads of the cylinder head bolts using the so-called “Screw in Screw” connection. This spacesaving screw concept of the supporting frame and cylinder head with cylinder block is an important prerequisite in achieving a short cylinder distance.SP57_06Cylinder block 7GB Engine mechanical components4-valve technologyTwo inlet and exhaust valves per cylinder are mounted vertically. Shape, size and location of the inlet and outlet ducts ensure an improved volumetric efficiency and a better gas exchange. The vertically positioned, centrally mounted unit injectors are directly located above the middle piston combustion cavity. This structure enables a good mixture formation. As a result, a low fuel consumption and reduced exhaust emissions are achieved.Outlet ductInlet ductSP57_07In order to achieve optimum flow characteristics in the inlet and outlet ducts turn the valve star 45° towards the engine longitudinal axle.Conventional positioning of the valvesValve star turned around 45°Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Outlet ductInlet ductSP57_08SP57_098GB Drive of the inlet and exhaust valvesExhaust camshaftBoth camshafts for the control of the inlet and exhaust valves are driven via a toothed belt. The valve actuation is performed via the roller rocker arms, which are located on the full floating axles.SP57_10Full floating axleInlet camshaftBecause of the installation conditions, the four roller rocker arms differ in shape and size.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Roller rocker armFull floating axleSP57_11Exhaust valve Full floating axle Inlet valveGB9 Engine mechanical componentsRoller rocker armRoller rocker arm Oil ductThey are moveable parts which are mounted on the full floating axle. The valve clearance balancing element is located directly above the valve stem. The oil is supplied from the full floating axle via an oil duct in the roller rocker arm to the valve clearance balancing element. A sliding shoe, which is located between the valve clearance balancing element and the valve stem is moveable and ensures an equal fuel distribution.Sliding shoe Valve stem Valve clearance balancing elementSP57_12Full floating axleProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Camshaft Roller rocker armStructure and function of the valve clearance balancing element The valve clearance balancing element consists of two moveable parts related to one another: the piston and the cylinder.Oil ductPistonOil storage chamberHigh pressure chamberBoth parts are pushed apart by the piston so far until there is no more play between the roller rocker arm and the camshaft. The nonreturn valve is used for filling and sealing the high pressure chamber.Piston springCylinderSP57_13Non-return valve Valve stem10GB Valve stroke If the cam presses onto the roller rocker arm, the non-return valve closes and there is a pressure build-up in the high-pressure chamber. The valve clearance balancing element acts like a rigid element when opening the inlet or the exhaust valve, as the oil cannot be compressed in the high pressure chamber.SP57_14Balancing of the valve clearance The cam does no longer press onto the roller rocker arm and the inlet and the exhaust valve is closed. The pressure in the high pressure chamber drops. The piston spring presses the cylinder and the piston so far apart until there is no more play between the roller rocker arm and the camshaft. The non-return valve opens, so that the oil can flow into the high pressure chamber.PlaySP57_15Valve seat ringsAdditional conductor Valve seat widthSP57_16Valve seat ringValve seatThe seal to the combustion chamber is made possible through the valve seat. In order to increase surface pressing and at the same time the tightening force in the contact area between the valve seat and the valve seat ring, the valve seat width is reduced by an additional conductor. This additional conductor ensures also a good swirl generation of the suctioned air.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Note: with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� The valve seat rings must not be reworked, otherwise the swirl of the streaming in air and thus the mixture formation is altered significantly. Only refacing is permissible.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedGB11 Engine mechanical componentsPistonValve pocket Combustion chamber cavityTop landThe pistons of the 2.0 ltr. TDI Engine have a centrally positioned combustion chamber cavity. A good swirl formation and thus an optimum mixture formation is achieved by this combustion chamber cavity. The dead space and thus also the low emissions are decreased through reducing the valve pocket depth and a top land width of only 9 mm.Cooling ductSP57_17Dead space valve pocketDead space top landDead space The dead space is the chamber, which the flame front cannot reach easily during the combustion cycle. In this area the fuel is only burned partially.SP57_18 SP57_34Cooling ductCooling ductProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The piston has a waveshaped cooling duct. When the oil is flowing through, the temperature in the area of the piston rings and piston crown drops. The wavy shape results in a larger surface of the cooling duct and therefore an improved heat transfer from the piston to the oil. As a result, the cooling effect is improved.SP57_1912GB Piston pin decentralizationPiston pin decentralization Piston pin decentralization means, that the piston is mounted off-center. This measure is intended for noise reduction, because the piston tilting in the top dead center is reduced.Cylinder axle Piston pin axleSP57_20During each inclination of the conrod piston side forces occur, which press the piston Protected by copyright. alternately against the unless cylinder wall.Copying for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP57_21SP57_22SP57_23In the area of the top dead center the piston side force changes its direction. There the piston is tilted towards the opposite cylinder wall and through this noise occurs. In order to reduce it, the piston pin axle is mounted offcenter.By decentralizing the piston pin axle, the piston already changes its side before top dead center as well as before the pressure increase and it rests on the opposite cylinder wall.GB13 Engine mechanical componentsToothed belt driveBoth camshafts as well as the coolant pump are driven via the toothed belt by the crankshaft.CamshaftToothed beltCoolant pumpCrankshaftToothed belt The 30 mm wide toothed belt is provided with a back fabric out of polyamide. The wear of the toothed belt edges is reduced through the back fabric.SP57_24Base material out of rubberBack fabric out of polyamideCover fabric out of polyamideSP57_25Cords out of glass fiberToothed belt guard For noise insulation, the toothed belt guard has on the inside a velvety flock material out of polyamide fibers.Toothed belt guardPolyamide fibersProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP57_26PlasticSP57_2714GB Tandem pumpBecause of the new cylinder head, the tandem pump has a new structure. It includes the vacuum pump and the fuel pump. The tandem pump is driven by the inlet camshaft.Vacuum pumpSP57_28Fuel pumpVacuum pump The vacuum pump consists of a rotor which is mounted off-center and a slideable vane positioned vertically to the rotor axle. The vane is out of plastic and it separates the vacuum pump in two chambers – suction side and pressure side. The vane constantly changes its position due to the rotary movement of the rotor. As a result, one of the chambers increases and the other chamber decreases.Air inlet from vacuum system Vane Drawn in air Suction side RotorThe air is suctioned on the suction side out of the vacuum system, which is pumped on the pressure side via a flutter valve in the cylinder head. The vacuum pump is supplied with oil via a duct to the cylinder head. The oil is used for lubricating the rotor and as a precise sealing of the vane to the pump housing.Vane Air outlet to cylinder head (flutter valve)RotorCompressed airProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness SP57_29 of information in this document. Copyright by ŠKODA AUTO A. S.�SP57_30Delivery side Oil ductGB15 Engine mechanical componentsFuel pumpFuel feed pressure control valve Strainer Pressure control valve Fuel return flow Return flow of the unit injectors Feed of the unit injectorsReturn flow to tank Feed from tankSP57_31The operation of the fuel pump is based on the principle of a crescent pump. The suction and delivery diagram of the fuel is shown in the individual illustrations on the movement of the red marked partial quantity within the pump. The fuel pressure is regulated by the pressure control valve in the fuel feed.Its maximum fuel pressure is 1.15 MPa at an engine speed of 4000 rpm. The pressure control valve in the fuel return flow maintains the fuel pressure in the return flow at approx 0.1 MPa. This ensures a uniform force ratio in the solenoid valves of the unit injectors.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP57_32SP57_3316GB Pump-nozzle unitFor the 2.0 ltr. TDI Engine with 4-valve technology, the unit injector was further developped. Features of the unit injector: • slim and compact structural shape, • fastening to the cylinder head with two screws, • increase of the injection pressure in the partial load range, • reciprocating piston-brake for reducing the injection noise, • newly formed, cone-shaped support of the unit injector in the cylinder head.SP57_35Fitting location The unit injector is located in the cylinder head. It is positioned vertically und mounted centrally directly above the piston combustion cavity.FasteningProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted The fastening of the unit injector is performed unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with two screws. This screwed connection with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� without nearly any radial stress reduces the structure-borne sound transfer from the unit injector to the cylinder head.SP57_36Fixing screwsGB17 Engine mechanical componentsConical seat The newly formed, cone-shaped support of the unit injector in the cylinder head makes it possible to achieve an optimum centering of the nozzle. As a new sealing concept between the injection nozzle and the cylinder head, the flat support with sealing washer has been modified to a conical seat. As a result, the previous heat shield gasket and the lower O-seal are no longer needed (see SSP 52, page 17).Cylinder headReciprocating piston-brake The reciprocating piston is located between the pump and the nozzle and controls the quantity as well as the duration of the preinjection. In order to reduce the injection noises, the unit injector is fitted with a reciprocating piston brake. For the unit injection system, injection noises can be caused by: • the steep pressure build-up and pressure drop in the reciprocating piston-pressure chamber, • the cavity formation (cavitation) after pressure drop, • the mechanical stop of the: – Reciprocating piston, – Solenoid valve needle, – Noozle needle.SP57_35 SP57_38Conical seatAs an effective and pratical measure for noise reduction, the reciprocating piston must brake before its mechanical stop, the so-called “reciprocating piston brake”.SP57_35The reciprocating piston brake reduces the hydraulic presssure via the reciprocating Alternative piston piston before the reciprocating piston reaches Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted its mechanical stop. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP57_3918GB Guide cylinder of reciprocating piston TrihedronWorking mode For the reciprocating piston brake, the guide cylinder of the reciprocating piston is equipped with three even surfaces (trihedron) and a control edge. The reciprocating piston is in a closed condition before the reciprocating movement.Control edge Alternative pistonPump-nozzle unitSP57_41Large reciprocating piston diameterImmediately after the commencement of the downward movement there is a high pressure build-up at the large reciprocating piston diameter and this enables a fast end of the preinjection.SP57_42Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted chamber unlesspressure authorised by Š KODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Reciprocating piston-As soon as the guide cylinder reaches the control edge via the three even surfaces, the feed to the reciprocating piston-pressure chamber is blocked. This immediately reduces the pressure at the large reciprocating piston diameter. As a result, the reciprocating piston strikes more slowly and the striking noise is reduced.GBSP57_4319 Engine managementSystem overviewSensorsEngine speed sender G28Hall sender G40Diesel direct injection system control unit J248 (engine control unit)Accelerator pedal position sender G79 Accelerator pedal position sender -2- G185Coolant temperature sender (radiator outlet) G83Intake air temperature sender G42 Charge air pressure sender G31 Brake light switch F Cruise control system brake pedal switch F47Diagnostic connectionClutch position sender G476Auxiliary signals: Vehicle speed signal CCS switch AC generator – terminal DFM Terminal 50 – starter signal AC compressor ON 20GBCAN DiagnosisFuel temperature sender G81K-wireCoolant temperature sender G62CAN DriveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Air by mass meter unless authorised ŠKODA AUTO A.G70 S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� ActuatorsUnit injector solenoid valve cyl. 1 - 4 N240 - 243Valve block consists of: • Solenoid valve for exhaust gas recirculation N18 • Solenoid valve for charge pressure control N75 • Exhaust gas recirculation cooler change-over valve N345Data bus diagnostic interface J533 GATEWAYIntake manifold flap motor V157CAN combiControl unit with display in dash panel insert J285Fuel pump relay J17 Fuel pump G6302535120 1 40km/h1620018015200 22051024 00Radiator fan control unit J293 Radiator fan V7 Radiator fan, right V35Glow period warning lamp K29 Fault indicator lamp for selfdiagnosis K83Oil level/oil temperature sender G266 SP57_44Automatic glow period control unit J179 Glow plug 1 Q10 Glow plug 2 Q11 Glow plug 3 Q12 Glow plug 4 Q13Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB21 Engine managementControl unit at CAN data busThe diagram illustrated below shows the linking of the diesel direction injection system control unit J248 to the CAN data bus structure of the vehicle. Information is transmitted via the CAN data bus to the control units. For example the diesel direction injection system control unit receives the speed signal from the speed sensor via the ABS control unit.J104J217J248J743Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�J533 J285 J519 J234SP57_45J527J104 J217 J234 J248 J285 J519 J527 J533 J743ABS with ESP control unit Automatic gearbox control unit Airbag control unit Diesel direct injection system Control unit with display in dash panel insert Electrical system control unit Steering column electronics control unit Data bus diagnostic interface J533 (Gateway) Direct shift gearbox mechatronicsCAN data bus “Drive” CAN data bus “Convenience” CAN data bus “Infotainment”22GB Engine speed sender G28Sealing flangeEngine speed sender G28The crankshaft sealing flange on the flywheel side is combined with the sensor rotor for the engine speed. The sealing ring in the sealing flange is made out of Polytetrafluorethylene (PTFE). The engine speed sender is a Hall sender. It is screwed into the housing of the crankshaft sealing flange. The sensor rotor is exactly positioned and pressed onto the crankshaft flange.SP57_46Reference mark Engine speed sender G28SP57_47The sensor rotor consists of a steel ring which is spray-painted with a rubber mixture. This rubber mixture contains a large amount of metallic swarfs, which are magnetized alternatively towards the north and south magnetic pole. As reference marks for the engine speed sender, two larger areas magnetized towards the north magnetic pole are located on the sensor rotor. It results in a 60 – 2 – 2 sensor rotor.North pole South poleSensor rotorUse of signalProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Effects of signal failure In case of failure of the engine speed sender, the engine continues to run in the emergency mode. At the same time the engine speed is limited to 3200 rpm to 3500 rpm.The engine speed and the exact position of the crankshaft is detected by the engine control unit through the engine speed sender signal. The injection quantity and the commencement of injection is calculated using this information.GB23 Engine managementHall sender G40Sensor rotorThe Hall sender is attached to the cylinder head below the inlet camshaft. It scans a sensor rotor, with which the position of the camshaft is detected.SP57_48Hall sender G40The sensor rotor on the camshaft is newly designed. In combination with the Hall sender G40 (camshaft), there is an emergency function, which enables the engine to continue operating also in case of a failure of the engine speed sender. On the circumference of the sensor rotor there are 4 segments with segment widths of 6°, 24°, 12° and 18° camshaft angle for the cylinder assignment. Another segment with a length of 45° camshaft angle is used for the cylinder assignment in the emergency mode.TDC cylinder 4TDC cylinder 3TDC cylinder 1 TDC cylinder 2Sensor rotorSP57_49Hall sender G40Use of signalEffects of signal failureWhen starting the engine the exact position of In case of signal failure, use the engine speed the camshaft to the crankshaft is detected with sender signal. The engine may not start the Hall sender signal. Determine together immediately, because the camshaft position with the engine speed sender signal G28 and thus the cylinders are not detected Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted which cylinder is located in the ignition TDC. immediately. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�24GB Emergency function In contrast to the previous TDI Engines, this engine continues to operate in case of failure or implausible signals of the engine speed sender. For the emergency function, the engine control unit only evaluates the rising sides of the segments of the Hall sender signal, because too many segment sides are detected and cannot be easily assigned by the engine control unit due to the vibrations caused during the starting procedure. The 45° segment is used as a reference mark for detecting the TDC cylinder 3. In emergency mode: • the engine speed is limited to 3200 rpm tp 3500 rpm, • the injection quantity is limited, • more time is required for the starting procedure.Signal formation of the Hall sender G40 (camshaft) and the engine speed sender G28 in normal operationCamshaft rotation 18° CS 45° CSProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�6° CS24° CS12° CS18° CSTDC 1TDC 3 Crankshaft rotationTDC 4TDC 2 Crankshaft rotationTDC 1CS = CamshaftSP57_50Signal formation of the Hall sender G40 (camshaft) and the engine speed sender G28 in emergency mode18° CS45° CS6° CS24° CS12° CS18° CSTDC 1TDC 3TDC 4TDC 2TDC 1CS = CamshaftSP57_51GB25 Engine managementClutch position sender G476The clutch position sender is clipped onto the master cylinder. It detects if the clutch pedal is operated.Clutch with clutch position senderUse of signal If the clutch pedal is operated • the cruise control system is deactivated and • the injection quantity is reduced briefly and therefore prevents the engine from jerking during gearshifts.SP57_52Tappet BracketMaster cylinderStructure The master cylinder is fixed via a bayonet connection to the bracket.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability When operating the clutch pedal, the tappet with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� moves the piston with the permanent magnet into the master cylinder.Clutch position senderSP57_53Piston with permanent magnetPedal travel26GB Working mode C l u tch pedal not ope rate d If the clutch pedal is not operated, the tappet and the piston with permanent magnet are in the off position. The analysis electronics in the clutch position sender sends a signal voltage to the engine control unit, which is 2 Volts below the supply voltage (battery voltage). The engine control unit then detects that the clutch pedal is not operated.Piston with permanent magnet TappetSP57_54Hall sender operating point Signal voltage to the engine control unitClutch position senderC l u tch pedal not ope rate d When operating the clutch pedal, the tappet is moved together with the piston with the permanent magnet towards the clutch position sender The permanent magnet is located at the front end of the piston. As soon as the permanent magnet overruns the operating point of the Hall sender, the analysis electronics only sends a signal voltage of 0 to 2 Volt to the engine control unit. It then detects that the clutch pedal is operated.Piston with permanent magnetTappetSP57_55Hall sender operating point Signal voltage to the engine control unitClutch position senderEffects of signal failure In case of signal failure of the clutch position sender, the cruise control system has no function and engine jerks can duringpurposes, in part or in whole, is not permitted Protected by copyright. Copying for occur private or commercial unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability gearshift. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB27 Engine managementAccelerator pedal position sender G79 and G185Both accelerator pedal position senders are components of the accelerator pedal module. In ŠkodaOctavia it is positioned vertically on the vehicle floor. In the accelerator pedal module are integrated: • Accelerator pedal, • Kinematics, • Kick-down force element (on vehicles fitted with automatic gearbox), • Lifter with accelerator pedal position senders G79 and G185, • Pedal stop.Accelerator pedal moduleSP57_56Besides the improved ergonomic properties, the new accelerator pedal module offers the advantage that no basic setting is required for The kinematics of the accelerator pedal the kick-down. The pedal stop is integrated at module converts the angle movement of the the module and through this the tolerances accelerator pedal to a linear movement. In the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted between the accelerator pedal and the stop on kinematics, the spring assembly ensures unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to apply. the correctness of information in this document. Copyright ŠKODA AUTO A. S.� the side of the body no longer together with by the frictional element the accustomed pedal touch.As a new feature, the pedal travel sensor is designed as a linear travel sensor. Both accelerator pedal position senders G79 and G185 operate contactless according to the induction principle.Accelerator pedal Accelerator pedal stopKick-down force element (automatic gearbox)Spring assemblySP57_57Metal plateSP57_58Frictional element of kinematicsKinematics Housing part with end cover and with the senders G97 and G185 located on the circuit board28GB Structure and design The circuit board has four layers and possesses two sensors G79 and G185 which operate independent of each other. This multi-layered arrangement on a circuit board makes it possible to assign to each sensor, a respective excitation coil, three reception coils and a control and analysis electronics. There are two excitation coils, six reception coils as well as two control and analysis electronics located on one circuit board. The reception coils of each sender have a rhomb shape and are assigned out of phase to each other. The metal plate is attached to the kinematics of the accelerator pedal module so that it moves at a short distance and in a straight line along the circuit board when operating the accelerator pedal.Plug housing with Pins 1 to 6 Circuit board housingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Circuit boardProcessors (control and analysis electronics)SP57_59Contact for pin connection Rhomb shape reception coils Excitation coilsPin assignment Pin 1 Supply voltage 5 V for G185 Pin 2 Supply voltage 5 V for G79 Pin 3 Earth for G79 Pin 4 Voltage signal of G79 Pin 5 Earth for G185 Pin 6 Voltage signal of G185GB29 Engine managementFunction The pedal electronics supplied by the engine control unit with a constant voltage of 5 Volt generates a high frequency alternating voltage, as a result an alternating current flows through the excitation coils. This generates an electromagnetic alternating field around the excitation coils and at the same time it is effective on a metal plate. As a result the inducted voltage in the metal plate evokes this time a second electromagnetic alternating field around the metal plate. This is constant within the excitation coils, i.e., it is independent of the accelerator pedal position. Both alternating fields (of the excitation coils and of the metal plate) are effective on the reception coils and induct a corresponding alternating voltage.Control and analysis electronicsfor diesel direct injection system control unit J248Metal plate Circuit board Excitation coilsSP57_60shape Protected by copyright. Copying for private or commercial purposes, in Rhomb part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability reception coils with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Electromagnetic metal plate alternating field Electromagnetic excitation coils alternating fieldThe position of the metal plate is a determining factor for the inducted alternating voltage of the reception coils. Depending on the accelerator pedal position, there is a varying overlapping of the metal plate to the reception coils. The amplitude sizes of the inducted alternating voltages in the reception coils differ depending on its position.An exact position determination is made possible through the rhomb shaped, out of phase location and varying direction of winding of the three reception coils. There will always be only one definable accelerator pedal position – refer to fig. SP57_75 on page 31. The varying direction of winding of the reception coils gives the resulting voltage signal in the reception coils a continuously changing direction. In the case of an identical overlapping of the reception coils a different voltage signal is received.Metal plate in idle position Metal plate in full load positionSP57_6130GB Output signal The analysis electronics proportions the different alternating voltages of the three reception coils to each other (ratiometering), whereby only the differential voltages are measured. The two reception coils which amplitude shows the smallest voltage level are very significant. Thus, it is achieved that only the part of the sinus signal with the largest linearity and sensitivity is used. In the present example (fig. SP57_75) it would be the red and blue illustrated reception coil.After the voltage evaluation, the result is converted into a linear constant voltage (see fig. SP57_62 on page 32) and is made available to the engine control unit at the sender output.Example: Accelerator pedal in partial load Metal plateU2 U1 U3SP57_75U1 0Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�sSP57_76Voltage curve of reception coil 1U2 0 sSP57_77Voltage curve of reception coil 2U3 0 sSP57_78Voltage curve of reception coil 3U1, U2, U3 – Voltage s – Metal plate path31GB Engine managementAdvantage Besides the contactless and thus wear-free working method, it is advantageous for both senders to use the ratiometering procedure. Due to the ratiometering, the path proportional output signal becomes independent to a large extent from the component tolerances and electromagnetic interferences. As magnetic materials are not necessary, there are hardly any deviations, which are caused by the decreasing magnetism. The output signals of both senders are generated in such a way that they are identical to the signals of the previous sliding contact senders.Kick-down area (automatic gearbox)V 5,0 G79G185SP57_620Accelerator pedal stop Accelerator pedal path in degrees Accelerator pedal stop up to kick-down force element (automatic gearbox)Use of signal The engine control unit uses the constant voltage signals of both senders for accelerator pedal Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted position to calculate theby injection unless authorised ŠKODA AUTO quantity. A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Effects of signal failure In case of failure of one or both senders, an entry is stored in the fault memory of the engine control unit and the fault lamp for self-diagnosis is switched on. The convenience functions, for example the cruise control system or the engine drag torque control are deactivated. In case of failure of a sender the system operates first of all in idle. If the second sender in the idle position is detected within a determined test period, the drive mode is again enabled. At desired full load, the speed is only slowly increased. In case of failure of both senders the engine runs only at increased idle speed (maximum 1500 rpm) and no longer reacts to the accelerator pedal.32GB Exhaust gas recirculation systemDuring the exhaust gas recirculation one part of the exhaust gases is led back to the suction side and again passed into the combustion chamber. Because the exhaust gases contain very little oxygen, the combustion peak temperature and thus also the combustion maximum pressure is reduced. This has as a consequence a reduction of nitrogen oxide emissions. The quantity of exhaust gases supplied to the combustion chamber is dependent on: – – – – – the engine speed, the injection quantity, the drawn in air mass, the intake air temperature and the air pressure.J248 G28 G70 G62 G28 G62 G70 J248 N18 N75 V157 N18 Engine speed sender Coolant temperature sender Air mass meter Diesel direct injection system Valve for exhaust gas recirculation Charge pressure control solenoid valve N345 Exhaust gas recirculation cooler change-over valve V157 Intake manifold flap motor A Exhaust gas recirculation valve B Vacuum unit C Radiator for exhaust gas recirculation D Vacuum pump E Catalytic converterSolenoid valve block A N345 N75B DCSP57_63Note: The exhaust gas recirculation is or influenced by in apart performance map in the engine Protected by copyright. Copying for private commercial purposes, or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability control unit. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB33 Engine managementSwitchable radiator for exhaust gas recirculation The 2.0 ltr./103 kW or 100 kW TDI Engine has a switchable radiator for exhaust gas recirculation.Coolant connection to exhaust gas recirculation valveRadiator for exhaust gas recirculationSP57_64from exhaust manifoldVacuum boxFunction principle of the exhaust gas recirculation The combustion temperature is decreased through the cooling of the supplied exhaust Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted gases unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability and a large mass of exhaust gases can be drawn in. This results in very little nitrogen oxide. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� A switchable radiator for exhaust gas recirculation is used so that the engine and the catalytic converter can reach their operating temperature more rapidly. The supplied exhaust gas is cooled down after reaching its operating temperature.34GB E x haust gas r e circula tion is switch e d o ff Up to a coolant temperature of 50 °C the exhaust gas flap remains open and the exhaust is guided past the radiator. Through this the catalytic converter and the engine reach their respective operating temperature within a short period of time.Engine control unit J248Valve for exhaust gas recirculation N18Exhaust gas recirculation valveCoolerExhaust gas recirculation cooler change-over valve N345Protected by copyright. Copying for private or commercial purposes, in part or in box whole, is not permitted Vacuum unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP57_65Exhaust gas flapE x haust gas r e circula tion switched o ff As of a coolant temperature of 50 °C the exhaust flap of the radiator is closed. Now the drawn in exhaust gas flows through the radiator.Solenoid valve blockCoolerExhaust gas recirculation cooler change-over valve N345 Vacuum box Exhaust gas flapSP57_66GB35 Engine managementPreheating systemA new preheating system is used in the 2.0 ltr./103 kW or 100 kW TDI Engine. The new preheating system is a diesel quick start system. It enables practically in all climatic conditions an “otto engine” immediate start without a long preheating. In combination with the 6-hole injection nozzle, which has a nozzle jet specially designed as an “ignition jet”, the new preheating system offers excellent cold start and cold running properties. The advantages of the new preheating system are: • Safe start at temperatures up to –24 °C • Extreme rapid heating-up time; within 2 seconds 1000 °C is achieved on the glow plug • Controllable temperature for preheating and afterglowing • Self-diagnosis capability • Euro-On-Board diagnosis capabilitySystem overviewDiesel direct injection system control unit J248 (engine control unit)Glow plug 1 Q10Automatic glow period control unit J179 Engine speed sender G28 CAN DriveGlow plug 2 Q11Data bus diagnostic interface J533 GATEWAYGlow plug 3 Q12CAN combiCoolant temperature sender G62Glow plug 4 Q13unit with Protected by copyright. Copying for Control private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO display A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability in dash panel with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� insert J285SP57_673025201/m 1/501015Glow period warning lamp K2936GB Automatic glow period control unit J179 The automatic glow period control unit receives the information for the glowing function from the engine control unit. The glow duration, the glow period, the actuation frequency and the duty cycle for the glow plugs are thus determined by the engine control unit.SP57_68The f unct ions of the a utom a tic glo w p e r i o d c o n tr o l u n i t a r e : 1. Switching of the glow plugs with a PWM signal (PWM = pulse width modulation) transmitted from the engine control unit • PWM-Low-Noise = Glow plug energized • PWM-High-Noise = Glow plug de-energized 2. Integrated excess voltage and excess temperature control unit deactivation, 3. Single plug monitoring Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted • Detection of overcurrent and short circuit inAUTO glow circuit unless authorised by ŠKODA A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� • Overcurrent deactivation of glow circuit • Diagnosis of glow electronics • Detection of an open glow circuit in case of failure of a glow plug30J317=T94/3 T94/30 T94/63J179J248= = = = J179 = J248 = J317 = Q10 - Q13 =Supply voltage Earth Control signal from engine control unit Diagnosis signal to engine control unit Automatic glow period control unit Engine control unit Voltage supply relay Glow plugQ10Q11 Q12 Q13 SP57_69GB37 Engine managementGlow plugs The glow plug is a component for cold start support. It creates ideal ignition conditions for the injected fuel through the electrically generated heat energy which is inducted in the combustion chamber. On the basis of the 4-valve technology, the spaces available for the glow plug are very limited. This is why the glow plugs have a slim structural shape.Connecting boltThe glow plug consists of a plug body, heating element and heating and control helix as well as a connecting bolt. The glow plugs have a nominal voltage of 4.4 Volt. In comparison to the conventional self-regulating metal glow plugs, the helix combination consisting of the control helix and the heating helix is shortened to about a third and through this the glow period is shortened to 2 seconds.Plug bodyConventional glow plugHeating elementGlow plug with shortened helix combinationControl helixHeating helixSP57_70SP57_71Note: Never inspect operation of glow plugs with 12 Volt, otherwise the glow plug will melt! Caution! Tightening torque for the glow plugs with shortened helix combination is 10 Nm.Glow plug Pump-nozzle unitFunction principle of the “ignition jet” The 2.0 ltr. TDI Engine has a 6-hole injection Ignition jet nozzle. One of the injection orifices is Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability designed so that the “ignition jet” has an with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� optimal distance to the glow plug. The cold start and cold running properties of the engine are improved through this “ignition jet”.SP57_7238GB Preglowing After switching on the ignition, the preglowing system is activated at a temperature below 14 °C. To do so the engine control unit transmits a PWM signal to the control unit for glow plug actuation. The glow plugs are also actuated with a PWM signal by the control unit for glow plug actuation. In the first phase of the preglowing, the glow plugs are operated for maximum 2 seconds with a voltage of approx. 11 Volt. After this, the glow plugs are supplied by the control unit for glow plug actuation with the necessary voltage which is required for the respective operating condition.1100 105035 30 25 20Temperature [°C]1000 950 900 850 800 750 0 5 10 15 20 25 Time [s] 30 35Temperature pattern of the glow plug during glowing Voltage [V]Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO 15 A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Voltage pattern with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�during the glowing10 5 40 0SP57_73After-glowing If the coolant temperature is below 20 °C, after-glowing occurs after each engine start, which reduces combustion noises and at the same time decreases hydrocarbon emissions. The actuation of the glow plugs is set by the engine control unit dependent on load and engine speed. When the engine is running the glow plug cools down through the air movemenent during load change. Furthermore the temperature of the glow plug decreases with increasing speed at a constant glow plug voltage. In order to compensate for the cooling effects, the voltage is increased by the engine control unit in line with a performance map which is dependent on load and speed.Note: As of a coolant temperature of 20 °C there is no more afterglowing. The afterglowing is interrupted after max. 3 minutes.GB39 Function diagram+30 +15 SJ317J29SS V157SSQ10 Q11 Q12 Q13MJ17931T94/ T94/ T94/ T94/ 49 3 5 6 T60/ T60/ 25 60 T94/ 1 T94/ 2 T94/ 4 T94/ 30 T94/ 63J248T60/ T60/ 31 32 T60/ 46 T60/ 1 T60/ 47 T60/ 48 T94/ 76 T94/ 38 T94/ 78 T94/ 62 T94/ 84 T94/ 39 T94/ 83 T94/ 61 T94/ 17 T94/ 15 T94/ 20J527N240 N241 N242 N243G42G31G79G185A B F F47 G6 G28 G31 G40 G42 G62 G70 G79 G81 G83CAN data bus Low G133 Fuel composition sender CAN data bus High G185 Accelerator pedal position sender -2Brake light switch G476 Clutch position sender CCS brake pedal switch (only manual gearbox) Fuel pump J17 Fuel pumpe relay Engine speed sender J179 Automatic glow period control unit Charge air pressure sender J248 Diesel direct injection system Hall sender J293 Radiator fan control unit Intake air temperature sender J317 Terminal 30 voltage supply relay Coolant temperature sender J329 Terminal 15 voltage supply relay Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Air mass meter unless J519 Electrical system control unit authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Accelerator pedal position sender J527 Steering column electronics control Fuel temperature sender unit Coolant temperature sender, N18 Valve for exhaust gas recirculation radiator outlet N75 Solenoid valve for charge pressure controlGB40 SS J519J329J293V7V35SSSSJ17 G476G70G6N345 N18 N75F47FT94/ 47T94/ 52T94/ 40T94/ 60T94/ 82T60/ 15T60/ 13T60/ 29T94/ 43T94/ 65T94/ 87T94/ 72T60/ 57T60/ 42T60/ 58T60/ 28T60/ 27T60/ 12T60/ 53T60/ 52T60/ 10T60/ 20T60/ 5T60/ 39T60/ 40T60/ 38T60/ 37T94/ 66T94/ 89G28G40G62G133G81G83SP57_74Colour coding Valve for pump-nozzle, cylinder 1 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Valve for pump-nozzle, cylinder unless 2 authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability in thissignal document. Copyright by ŠKODA AUTO A. S.� Input Valve for pump-nozzle, cylinder 3 with respect to the correctness of information Valve for pump-nozzle, cylinder 4 Output signal Exhaust gas recirculation cooler change-over valve Supply voltage Q10 Glow plug 1 Q11 Glow plug 2 Earth Q12 Glow plug 3 CAN data bus Q13 Glow plug 4 S… Fuse Bidirectional V7 Radiator fan V35 Radiator fan, right Diagnostic connection V157 Intake manifold flap motor N240 N241 N242 N243 N345GB41 NotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�42GB Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB43