TECHNICAL DOCUMENTATION
SSP 067 Diesel engine 2.0 ltr

This PDF is currently unavailable.
Read document text
Service67Diesel engine 2.0 ltr./125 kW TDIwith Common Rail injection system, in part or in whole, is not permitted s not guarantee or accept any liability opyright by ŠKODA AUTO A. S.�Self-study programmeThe 2.0 ltr. TDI engine with Common Rail injection system is the first representative of a new generation of diesel engines in Škoda vehicles. Excellent characteristics were achieved while maintaining a low consumption through the combination of the successful and proven 2.0 ltr. TDI engine with the Common Rail technology.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�These outstanding TDI qualities of the 2.0 ltr. TDI engine with Common Rail injection system are oriented toward the continuously growing challenges in terms of acoustics, comfort as well as exhaust after treatment. The engine already meets the currently valid emission standard Euro 5, which prob ably takes effect at the end of 2009 while offering the potential to comply with future emission standards through the integrated technologies.GBContentsBrief Technical highlights Engine mechanical components The cylinder head The intake manifold with baffle flaps The drive of the camshafts The toothed belt drive The oil circulation system The crankcase ventilation The cooling circuit The low exhaust gas recirculation temperature The fuel system Engine management System overview The engine management The exhaust turbocharger The diesel particle filter system The preheating system Function diagram Remarks 4 5 6 7 10 12 14 15 16 20 21 22 40 40 42 43 46 53 56 58You will find the instructions for the installation, removal, repair, diagnosis and detailed user information in the repair manual, the diagnosis Protected by copyright. Copying private or commercial purposes, in part or in whole, is not permitted unit VAS 505x and in the for onboard literature. The time for going to press was on the 06/2008. This brochure is not subject to the update.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBBriefIntroductionThe 2.0 ltr./125 kW TDI engine with Common Rail injection system is based on the 2.0 ltr./125 kW TDI engine with unit injection system, which is one of the most common 2.0 ltr. diesel engines produced worldwide. This is the most widely used engine in the company Volkswagen, from the passenger car to the transport vehicle.SP67_01SP67_02Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�In order to comply with the increased demands in terms of acoustics, consumption and exhaust emissions, a multiplicity of engine components were improved. Therefore, the complete change-over of the injection system to the Common Rail technology is of particular importance. When a diesel particle filter is fitted, the engine meets the currently valid emission standard Euro 5, which probably takes effect at the end of 2009. Due to the legal specifications of the authorisation conditions for the emission standard Euro 5, which have not been determined at present, the engine is licensed to meet the emission standard Euro 4.GBTechnical highlights- Common Rail injection system with Piezo injection valves - Oxidation catalytic converter with diesel particle filter - Intake manifold with baffle flap adjustment - Electrical exhaust gas recirculation valve - Exhaust turbocharger with variable turbine geometry - Low exhaust gas recirculation cooling temperature - two balance shafts in the crankcase *SP67_03Power output and torque Technical data unless diagram authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilityProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�140 130 120 110 100 90 80 70 P (kW) 60 50 40 30 20 10350 325 300 275 250 225 200 175 M (Nm) 150 125 100 75 50 25 0 1000 2000 3000 4000 5000 6000 7000 n (min-1)Engine code letters: Type: Number of cylinders: Valves per cylinder: Displacement: Bore diameter: Stroke: Compression ratio: Max. power output: Max. torque: Engine management: Fuel: Exhaust cleaning: Emission standard: CBBB/CEGA Inline engine 4 4 1968 cm3 81 mm 95.5 mm 16,5 : 1 125 kW at 4200 min-1 350 Nm at 1750 - 2500min-1 Bosch EDC 17 (Common Rail injection system) Diesel Exhaust gas recirculation; diesel particle filter; oxidation catalytic converter EU4 plusSP67_04* only engines with the engine code letters CBBBGBEngine mechanical componentsThe crankshaftDue to the high mechanical stresses, a forged crankshaft is used for the 2.0 ltr./125 kW TDI engine with Common Rail injection system. Instead of the usual eight counterbalances, this crankshaft has only four counterbalances. Through this the load of the crankshaft bearing is reduced. Furthermore, noise emissions which result from proper motions and oscillations of the engine are reduced.SP67_05CounterbalancesCounterbalancesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Serration ofoil pumpThe pistonsThe pistons have no valve pockets just like on the 2.0 ltr./125 kW TDI engine with unit injection system. This measure improves the so-called dead space and the swirl formation in the cylinder. A "swirl" is a circular flow movement around the vertical cylinder axle. The swirl has a substantial influence on the quality of the mixture formation.Piston 2.0 ltr./125 kW TDI unit injection engine Piston 2.0 ltr./125 kW TDI Common Rail engine Piston recessCooling ductSP67_07SP67_06In order to cool the area of the piston rings, the piston has an annular cooling duct through which oil is injected by way of piston spray nozzles. The piston recess, in which the injected fuel is swirled and mixed with air, is synchronized with the spray position of the injection nozzles and has a broader and flatter geometry compared to the piston used for the 2.0 ltr./125 kW TDI unit injection engine. Thus, a homogeneous mixture formation is obtained and the soot formation is reduced.GBThe cylinder headThe cylinder head of the 2.0 ltr./125 kW TDI engine with Common Rail injection system is a crossflow aluminium cylinder head with two inlet and two exhaust valves per cylinder. The valves are hung in a vertical position. The two overhead camshafts are connected via a spur gear tooth system with integrated balance of the tooth flank play. The drive of the crankshaft is performed by means of a toothed belt and the camshaft sprocket of the exhaust camshaft. The valves are operated via low-friction roller rocker arms with hydraulic valve play compensation elements.Injection valvesInlet camshaftExhaust camshaftSP67_08Roller rocker armInjection valveClamping clawThe injection valves are secured in the cylinder head with clamping claws. They can be removed via small covers in the cylinder head cover.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP67_09GBEngine mechanical componentsVentilation duct in the cylinder headIn the event of possible leakages in the area of the copper injection valve gasket ring, the air in the combustion chamber can escape from a duct. The ventilation duct is arranged in the cylinder head above the exhaust manifold. It prevents the overpressure from the combustion chamber to reach the compressor side of the exhaust turbocharger via the crankcase ventilation in order to avoid possible functional disturbances.Injection valveGasket ringVentilation ductSP67_10Gasket ring to combustion chamber Ventilation ductsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP67_11GBThe 4-valve technologyFor each cylinder, two inlet and two exhaust valves are hung in a vertical position in the cylinder head. The vertically positioned and centrally mounted injection valve is directly located above the middle piston recess.Inlet camshaft Exhaust camshaft Baffle channel Filling channelOutlet valvesSuction valvesSP67_12Shape, size and location of the inlet and outlet ducts ensure a good volumetric efficiency and a more advantageous gas exchange in the combustion chamber. The inlet ducts are designed as a baffle channel and a filling channel. The air flow through the filling channel enables a good filling of the combustion chamber, especially during high engine speeds.The air flow through the baffle channel produces the desired high charge movement.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability GB with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Engine mechanical componentsThe intake manifold with baffle flapsSteplessly adjustable baffle flaps are located in the intake manifold. The swirl of the intake air is adjusted by positioning the baffle flaps depending on the engine speed and load. The baffle flaps are operated by the intake manifold flap motor V157, which itself is controlled by the engine control unit. The potentiometer for the intake manifold flap G336 is integrated in the intake manifold flap motor V157 and provides the current position feedback of the baffle flaps for the engine control unit.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Intake manifoldIntake manifold flap motor V157SP67_22Intake manifold moduleCollective intake manifoldSP67_23Baffle channelFilling channelBaffle flapIntake manifold flap motor V157 with potentiometer for the intake manifold flap G33610GBFunction of the baffle flaps The baffle flaps are closed in idle and at low speeds. The sucked air flow now travels through the baffle channel. This produces a high swirl effect which leads to a good mixture formation in the combustion chamber. In the driving mode, the baffle flaps are continuously adjusted in line with the load and engine speed. An optimal air movement is therefore available for each operating range in the combustion chamber. The baffle flaps are completely opened as of a speed of approx. 3000 rpm. A good filling of the combustion chamber is achieved through the increased air rate.Baffle flap – closedSpeed as of 3000 rpmBaffle flapBaffle flapFilling channelFilling channelBaffle channelBaffle channelSP67_24SP67_25The baffle flaps are opened depending on the speedOpening of the flaps in %100The baffle flaps are opened when starting the engine, in emergency mode and at full load.0 1000 2000 3000 1/minSP67_26GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�11Engine mechanical componentsThe drive of the camshaftsThe inlet and exhaust camshafts are connected via a spur gear tooth system with integrated balance of the tooth flank play. At the same time the spur gear of the inlet camshaft is driven by the spur gear of the exhaust camshaft. The spur gear of the exhaust camshaft consists of two parts. The balance of the tooth flank play ensures a reduced noise of the camshafts.Supporting frameInlet camshaftSP67_13moveable spur gear Exhaust camshaft Spacer washerSP67_14fixed spur gear disc spring Circlip moveable spur gear fixed spur gearStructureProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The fixed spur gear is frictionally connected to the exhaust camshaft. Ramps are located at the front side. The moveable spur gear can be radially and axially moved. Recesses for the ramps are located on its reverse side.RampsSP67_1512GBIt functions as follows: Both parts of the spur gear are pushed towards each other in the axial direction with the force of a disc spring. Simultaniously, the moveable spur gear is accomodated opposite the fixed spur gear in a rotative angular movement.SP67_16Disc springCompensation of playProtected by movement copyright. Copying for private or a commercial The rotative angular leads to tooth purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� mismatch of both parts of the spur gear and therefore enables the balance of the tooth flank play between the gears of the inlet and exhaust camshafts.Tooth mismatchSP67_17GB13Engine mechanical componentsThe toothed belt driveThe exhaust camshafts, the coolant pump and the fuel high pressure pump are driven by means of the toothed belt.Camshaft drive wheel Toothed belt driveDrive wheel of the high pressure pump Tensioning pulleyDrive wheel coolant pumpGuide pulleyAlternator (with alternator freewheel)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�AC compressorCrankshaftSP67_18Tensioning pulleyAuxiliary driveThe drive of the auxiliariesThe auxiliaries, comprising the alternator and the AC compressor, are driven by the crankshaft via a V-ribbed belt. The profile surface of the V-ribbed belt has a fibrous coating. Thus, the friction behaviour of the belt is improved. Therefore, disturbing noises which can occur in wetness and coldness or at low temperatures are reduced.V-ribbed beltTooth profilefibrous coatingSP67_1914GBThe oil circulation systemA duocentric oil pump produces the required oil pressure for the engine. It is integrated in the balance shaft module and is driven via one of the balance shafts. The oil circulation system has a pressure relief valve. The pressure relief valve prevents the components of the engine to get damaged through high oil pressure, for example at low outside temperatures and at high engine speeds. The oil pressure regulator valve controls the oil pressure of the engine. It opens as soon as the oil pressure has reached the maximum permissible value. The short circuit valve opens when the oil filter is plugged and through this secures the lubrication of the engine.Legend 1 2 3 4 5 6 7 8 - - - - - - - - SP67_209 - Oil pressure switch F1 Oil pan 10 - Oil pressure regulator valve Oil level and temperature sender G266 11 - Crankshaft Oil pump Spray nozzles for piston cooling Oil pressure relief valve Protected by copyright. Copying12 - for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability 13 - Camshaft Oil return flow check tube unless with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� 14 - Vacuum pump Oil cooler 15 - Turbocharger Oil filter 16 - Oil return flow Short circuit valveGB15Engine mechanical componentsThe crankcase ventilationOn combustion engines, the pressure differences between the combustion chamber and the crankcase produce air flows between the piston rings and the cylinder running surface, the so-called “blowby gases” (gas outlet from the crankcase). These oleiferous "blow-by gases" are led back again via the crankcase ventilation into the suction area so that the environment is not polluted. The increased demands in terms of environmental protection put high expectations on an effective oil separation. Through a stepwise deposition, only a minimum oil carryover in the intake air and therefore also less soot emissions occur. The oil separation occurs in three steps: - the coarse separation - the fine separation - the damping volume The components of the crankcase ventilation are integrated in the cylinder head cover beside the oil filler neck and the pressure accumulator for the vacuum system of the engine.Damping volume Vacuum reservoir Pressure control valve Oil filler neckin part or in whole, is not permitted Protected by copyright. Copying for private or commercial purposes, unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Coarse separationFine separationSP67_21Coarse separation The "blow-by gases" originating from the crankshaft/camshaft space form a damping volume. This is integrated in the cylinder head cover. In the damping volume, the larger oil drops are dispersed against the walls and gather along the floor itself. The oil in the cylinder head can drain off via the openings of the damping volume.16GBStructureto the bleeding sectionCover Diaphragm Driver pad Coil spring Pressure control valveDamping volume Flutter valveCycloneDamping volumeProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Flutter valve Legend oil-filled air of crankcase oil-free air Oil returnOil collection volumeSP67_27GB17Engine mechanical componentsFine separation The fine separation from the "blow-by gases" is performed via a cyclone separator which consists of a total of four cyclones. Depending on the force of the pressure difference between the intake pipe and the crankcase, two or four cyclones are switched on by means of the flutter valves made of spring steel. The air circulates in a rotative movement due to the shape of the cyclone. The oil mist is sprayed onto the separator by means of the occuring centrifugal force. The oil drops are dispersed against the housing wall of the cyclone and are gathered in a collection volume.cleaned air to the suction channelPressure control valve Flutter valves CycloneProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP67_28Oil collection volumeFlutter valveWhen the engine is standing in still motion a flutter valve opens, which is closed during engine operation due to the higher pressure in the cylinder head. After this valve is opened, the oil from the collec tion volume returns to the oil pan via the cylinder head.18GBPressure control valve The pressure control valve regulates the pressure for venting the crankcase. It consists of a diaphragm and a pressure spring. When introducing the "blow-by gases", the pressure control valve limits the vacuum in the crankcase so that the engine seals are not damaged if the vacuum is too high.Pressure control valve – opened Diaphragm Pressure springIf the vacuum in the suction channel is low, the valve opens through the force of the pressure spring. If the vacuum in the suction channel is high, the pressure control valve closes.Pressure control valve - closed atmospheric pressureto the suction sectionSP67_29SP67_30Damping volume In order to avoid disturbing flow swirls when the gases are entering the intake manifold, a damping volume connects to the cyclone oil separator. In this area, the kinetic energy of the gases from the cyclones is reduced. In the damping volume as well, a residual amount of oil is again dispersed.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�to the suction sectionDamping volumeSP67_31GB19Engine mechanical componentsThe cooling circuitThe coolant in the cooling circuit circulates by means of a mechanical coolant pump. It is driven via the toothed belt. The circulation system is actuated by an expanding material thermostat, the coolant regulator.SP67_32Legend 1 2 3 4 5 6 - - - - - - 7 - Coolant temperature sender at radiator outEngine cooling system for cooler let G83 Coolant regulator 8 - Heat exchanger for heating Coolant pump 9 - Expansion reservoir Oil cooler 10 - Pump 2 for coolant circulation V178 Exhaust gas recirculation cooler Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Coolant temperature sender unless authorised by ŠKODA AUTO A. G62 S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�20GBThe low exhaust gas recirculation temperatureFor reducing the NOx emissions, the engine is installed with a low exhaust gas recirculation temperature.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP67_33Function: When the coolant regulator (thermostat) is closed, the exhaust gas recirculation cooler is supplied directly with cold coolant from the engine radiator. On the basis that the temperature gradient is therefore considerably higher, a greater exhaust gas quantity can be led back. As a result of the combustion temperatures, the nitrogen oxide emissions can be further reduced during the warming-up phase of the engine.GB21Engine mechanical componentsThe fuel system1 – Fuel pump for pre-supply G6 Continuously supplies fuel in the fuel feed.2 - Fuel filter with preheating valve At low outside temperatures, the preheating valve prevents the filter from clogging through paraffin crystals which have crystallized out. 3 - Additional fuel pump V393 Delivers the fuel from the fuel feed to the high pressure pump 4 - Filter sieve Protects the high pressure pump from dirt particles. 5 - Fuel temperature sender G81 Detects the current fuel temperature. 6 - High pressure pumpunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Produces the high fuel pressure required for the with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� injection. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted7 - Valve for fuel dosage N290 Controls the quantity of fuel to be condensed based on need.22GB8 - Fuel pressure regulating valve N276 Regulates the fuel pressure in the high pressure area. 9 - High pressure accumulator (Rail) Gathers the fuel, under high pressure, required for the injection of all the cylinders. 10 – Fuel pressure sender high pressure G247 Detects the current fuel pressure in the high pressure area. 11 - Pressure holding valve Maintains the return flow pressure of the injection valves at approx. 1 MPa. This pressure is required for the function of the injection valves.12 - Injection valves N30, N31, N32, N33Legend High pressure Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP67_34(23-180 MPa)Return flow pressure of the injection valves (1 MPa) Supply flow pressure Return flow pressureGB23Engine mechanical componentsThe Common Rail injection system The 2.0 ltr./125 kW TDI engine is equipped with a Common Rail injection system for the mixture preparation. The term "Common Rail" means "common rail" and stands for a common fuel high pressure accumulator for all the injection valves of a cylinder bank.High pressure accumulator (Rail)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP67_35High pressure pumpThe pressure which is produced and the fuel injection itself are separated from each other in this injec tion system. A separate high pressure pump produces the high fuel pressure required for the injection. The fuel pressure is kept in a high pressure accumulator (Rail) and is led to the injection valves (injec tors) via short injection lines. The Common Rail injection system is operated by the Bosch EDC 17 Engine Management System.24GBCharacteristics of the Common Rail injection system: - the injection pressure is almost freely selectable and can be adapted to the respective operating condition of the engine - a good mixture formation is obtained with a high injection pressure of maximum 180 MPa - a flexible injecting process with several pre- and post injections The Common Rail injection system offers many design possibilities in order to adapt the injection pressure and the injecting process to the operating condition of the engine. Thus, it has very good requirements in order to fulfil the continuously increasing demands on low fuel consumption, low pollutant emissions and a smooth engine running for the injection system.Injection valves N30, N31, N32, N33Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Fuel pressure regulating valve N276Fuel pressure sender G247High pressure accumulator (Rail)Fuel feed system to high pressure accumulator (Rail)Valve for fuel dosage N290High pressure pumpSP67_36GB25Engine mechanical componentsInjection valves Piezo-controlled injection valves are used in the Common Rail system of the 2.0 ltr. TDI engine. Therefore the injection valves are actuated via a piezo actuator. The biggest advantage of the piezo actuator is its switching speed which is about four times higher in respect to previously used solenoid valves. Furthermore, the piezo technology has about 75% less moveable mass on the nozzle needle compared to the injection valves controlled by a solenoid valve. This can result in the following advantages: - very short switching times - several injections per work cycle possible - precisely dosable injection quantitiesFuel feed system (high pressure connection)electrical connectionEdge-type filterFuel return flowPiezo actuatorCoupling piston Valve piston Valve piston springProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Switching valveThrottle plate Nozzle spring Gasket ring nozzle needle Nozzle needleSP67_3726GBInjecting process On the basis of the short switching times of the piezo-controlled injection valves, it is possible to flexibly and accurately actuate the injection phases and the injection quantities. Thus, the injecting process can be adapted to the respective requirements for the operating conditions of the engine. Five part injections are performed per injecting process.Actuation voltage (V)Injection (injection rate)Time Pre-injection Main injection Post injectionSP67_38Pre-injectionMain injectionA small quantity of fuel is injected into the comAfter the preinjection, the main injection quantity bustion chamber before the main injection. This is injected into the combustion chamber after a results in a temperature and pressure increase in short injection pause. the combustion chamber before the main injec The high level of the injection pressure remains tion. Thus, the firing delay of the main injection is nearly the same during the complete injection shortened and the pressure increase as well as procedure. the pressure peaks in the combustion chamber are therefore reduced. This results in low combustion noises and low exhaust emissions. The number, the timing and the injection quantities of Post injection the preinjections depend on the operating condition of the engine. Two post injections are still required for a regenWhen the engine is cold and the speed is low, eration of the diesel particle filter. The exhaust two preinjections are carried out for acoustic gas temperature, which is necessary for the compurposes. bustion of the soot particles in the diesel particle When the load and speed are high, only one filter, is increased by the post injections. preinjection is carried out in order to reduce the exhaust emissions. Protected by copyright. for private or is commercial purposes, in part or in whole, is not permitted At full load and high speed, noCopying preinjection unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to thequantity correctness of information in this document. Copyright by ŠKODA AUTO A. S.� carried out because a large of fuel must be injected during the main injection in order to achieve a high degree of efficiency.GB27Engine mechanical componentsIntegrated calibration and acquisition system (INCA) The integrated calibration and acquisition system (INCA) is a software function in the diesel direct injection system control unit J248 for increasing the accuracy of fuel injection quantities. This function enables to individually correct the injection quantity for each injection valve of the Common Rail injection system in the complete performance map. Thus, the accuracy of the injection system is improved. Various injection behaviours of the injection valves, which result from the production toleranc es, are compensated with the integrated calibration and acquisition system. The advantages of this injection quantity control method are: - Reduction of the fuel consumption - Reduction of the exhaust gas quantity - smooth engine runningINCA value A 7-digit adaptation value, comprised of letters and numbers, is stamped on each injection valve. The INCA value is determined according to the production of each injection valve. It outlines the difference with the specified value and therefore describes the injection behaviour of an injection valve. The diesel direct injection system control unit J248 can precisely calculate the required actuation period for the injection of each injection valve using the INCA value.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�INCA valueIf an injection valve (injector) is replaced, it must be adapted to the injection system. An integrated calibration and acquisition must be performed. Please perform the integrated calibration and acquisition using the targeted fault finding!SP67_77* IntegratedCalibrationAcquisition system (INCA) 28GBAdditional fuel pump V393 The additional fuel pump is a roller cell pump which is located in the engine compartment. It has the task of delivering the fuel from the fuel tank into the fuel feed to the high pressure pump. The additional fuel pump is activated via a relay using the engine control unit and increases the pressure of the fuel, which is led to the fuel tank from the electrical fuel pump, up to approximately 0.5 MPa. Thus, the fuel supply of the high pressure pump is ensured in all operating conditions. Effects of failure If the additional fuel pump fails, the engine runs first of all with reduced power output. It is not possible to start the engine again.SP67_39Additional fuel pump V393Additional fuel pump V393from the fuel tankProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S. � SP67_40to the high pressure pumpelectrical connectionsFilter sieve In order to protect the high pressure pump from dirt particles, for example through mechanical abrasion, a filter sieve is located in the fuel feed system in front of the high pressure pump.from the additional fuel pump V393SP67_41Filterto the high pressure pumpGB29Engine mechanical componentsHigh pressure pump The high pressure pump is a 1-piston pump. It is driven by the crankshaft via the toothed belt. The high pressure pump has the task to produce the high fuel pressure required for the injection of up to 180 MPa. During the work cycle of the respective cylinder, the pressure is produced synchronously with the injection by way of two cams on the drive shaft offset by 180°. Thus, the pump drive is evenly stressed in order to keep the pressure fluctuations in the high pressure area very low. A roller ensures a low-friction power transmission of the drive cams on the pump piston.StructureValve for fuel dosage N290 Suction valveExhaust valve Connection to high pressure accumulator (Rail) Fuel sourcePump piston lPiston springProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Fuel return flowRollerOverflow valveDrive shaftDrive camsSP67_4230GBWhen setting the engine timing, the position of the drive shaft for the high pressure pump must be adjusted. For this reason, observe the instructions in the Workshop Manual.Structure of the high pressure pump - schematicSuction valveExhaust valveValve for fuel dosage N290Connection to high pressure accumulator (Rail) Pump plunger Fine filterPiston spring Overflow filter RollerDrive shaft with camsSP67_43GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�31Engine mechanical componentsHigh pressure area The high pressure pump is supplied with sufficient fuel through the additional fuel pump in each operating mode of the engine. The fuel reaches the high pressure area of the engine via the valve for fuel dosage N290. The pump piston is moved up and down by the cams on the drive shaft.Exhaust valve Connection to high pressure accumulator (Rail)Valve for fuel dosage N290Pump plungerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Drive shaft with camsSP67_44Fuel feed system of the additional fuel pump32GBSuction stroke The downward movement of the pump piston, the so-called suction stroke, leads to a volume increase of the compression chamber. This results in a pressure difference between the fuel in the high pressure pump and in the compression chamber. Due to the pressure difference, the suction valve opens and the fuel flows into the compression chamber.Suction valveCompression chamberPump plungerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP67_45GB33Engine mechanical componentsDelivery stroke With the start of the upward movement of the pump piston, the pressure in the compression chamber increases and the suction valve closes. As soon as the fuel pressure in the compression chamber rises above the pressure in the high pressure area, the outlet valve (non-return valve) opens and the fuel reaches the high pressure accumulator (Rail).Connection to high pressure accumulator (Rail)Exhaust valveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Pump plungerSP67_4634GBfor fuel dosage N290 The valve for fuel dosage is integrated in the high pressure pump. It ensures that the fuel pressure in the high pressure area is controlled in a way which fulfils the demand. The valve for fuel dosage controls the fuel quantity which is needed to produce high pressure. This has the advantage that the high pressure pump must only produce the pressure which is required for the current operating situation. Thus, the power consumption of the high pressure pump is reduced and an unnecessary heating of the fuel is avoided. Function In de-energized condition, the valve for fuel dosage is open. If the supply quantity to the compression chamber decreases, the valve for fuel dosage is actuated by the engine control unit with a pulse width modulation (PWM) signal. The valve for fuel dosage is closed with clock pulses by way of the PWM signal. Depending on the PWM signal frequency variation, the position of the control piston changes and thereby the supply quantity of the fuel in the compression chamber of the high pressure pump.to the compression chamberControl pistonSP67_47Effects of failure When the valve for fuel dosage fails, the engine performance is reduced and the engine management Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted runs in the emergency mode. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB35Engine mechanical componentsLow pressure area Overflow valve The fuel pressure in the low pressure area of the high pressure pump is regulated by the overflow valve. Function The additional fuel pump delivers the fuel from the fuel tank to the high pressure pump with a pressure of approx. 0.5 MPa. The overflow valve regulates the fuel pressure in the high pressure pump to approx. 0.43 MPa. The fuel delivered by the additional fuel pump acts against the piston and the piston spring of the overflow valve. If the fuel pressure exceeds 0.43 MPa, the overflow valve opens and clears the way to the fuel return flow. The excess fuel delivered flows via the fuel return flow into the fuel tank.Overflow valveFuel return flow Fuel feed Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� SP67_4836GBControl of the high fuel pressure A so-called two-actuator concept controls the fuel high pressure for the Common Rail injection system. To do so, the fuel pressure regulating valve N276 and the valve for fuel dosage N290 are actuated by the engine control unit with a pulse width modulation signal (PWM signal). Depending on the operating condition of the engine, the control of the high fuel pressure is performed by one of the two valves. Therefore, the other respective valve is only actuated by the engine control unit. Control by the fuel pressure regulating valve N276 When starting the engine and heating the fuel, the fuel pressure regulating valve N276 controls the fuel high pressure. In order to quickly heat up the fuel, the fuel high pressure pump delivers more fuel and compresses it more than necessary. The surplus fuel is delivered back into the fuel return flow by the fuel pressure regulating valve N276. Control of the fuel high pressure by both valves In idle, in the trailing throttle and at low injection quantites, the fuel pressure is regulated simultaniously by both valves. Therefore a precise control of the fuel pressure is achieved, which improves the idle quality and the transition into the trailing throttle. Control by the valve for fuel dosage N290 At high injection quantites and at high pressures of the rail, the fuel high pressure is controlled by the valve for fuel dosage N290. Therefore a control of the high fuel pressure occurs, which fulfils the demand. The power consumption of the high pressure pump is reduced and an unnecessary heating of the fuel is avoided.Two-actuator conceptControl of the high fuel pressure by the fuel pressure regulating valve N276Injection quantityControl of the high fuel pressure by the valve for fuel dosage N290Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Control of the fuel high pressure by both valvesSP67_49GB37Engine mechanical componentsFuel pressure regulating valve N276 The fuel pressure regulating valve N276 is located on the high pressure accumulator (Rail). The fuel pressure needed is set by the opening and the closing of the regulating valve N276. To do so, it is actuated by the engine control unit with a pulse width modulation signal.Fuel pressure regulating valve N276SP67_50Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�StructureSolenoid coil High pressure accumulator (Rail) Valve needle Valve armature electrical connectionSP67_51Return flow to fuel tankValve spring38GBIt functions as follows In contrast to the previous regulating valves in the Common Rail injection system, this valve is open in the de-energized condition.Regulating valve in the rest position (engine "off") If the regulating valve is not actuated, the pressure control valve is opened by the valve springs. The high pressure area is connected to the fuel return flow. Thus, a volume compensation between the fuel high pressure area and the low pressure area is ensured. During the cooling-down process, fuel bubbles which can occur in the high pressure accumulator (Rail) when the engine is standing in still motion are avoided and therefore the starting behaviour of the engine is improved.Valve springSP67_52Regulating valve actuated (engine "on") In order to set an operating pressure of 23 to 180 MPa in the high pressure accumulator, the regulating valve is actuated by the engine control unit J623 with a pulse width modulation (PWM) signal. Thereupon a magnetic field arises in the solenoid coil. The valve armature is tightened and presses the valve needle into its position. Thus, a magnetic force is opposed to the fuel pressure in the high pressure accumulator. Depending on the PWM signal frequency, the cross-section of flow to the return flow line changes and therefore the flow rate as well. Furthermore, pressure fluctuations in the high pressure accumulator can be compensated through this.Engine control unit J623SP67_53Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Effects of failure When the regulating valve for the fuel pressure fails, it is not possible to run the engine because an adequate high fuel pressure cannot build up for the injection.GB39Engine managementSystem overviewSensorsEngine speed sender G28 Glow period warning lamp K29Hall sender G40 Accelerator pedal position sender G79/ Accelerator pedal position sender 2 G185 Air mass meter G70 Coolant temperature sender G62 Radiator outlet coolant temperature sender G83 Charge pressure sender G31 Intake air temperature sender G42unless authorised by Š KODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Fuel temperature sender G81 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedDiesel particle filter warning lamp K231Exhaust emissions warning lamp K83Control unit in dash panel insert J285Fuel pressure sender G247Exhaust gas recirculation potentiometer G212 Lambda probe G39 Exhaust pressure sensor 1 G450 Exhaust gas temperature sender 1 G235 Exhaust gas temperature sender 3 G495 Exhaust gas temperature sender 4 G648 Brake light switch F Clutch position sender G476 Position sender for charge pressure regulator G581Potentiometer for the intake manifold flap G336 Throttle valve potentiometer G69 40GBActuatorsFuel pump relay J17 Fuel pump for pre-supply G6 Additional fuel pump relay J832 Additional fuel pump V393 CAN data bus driveInjection valves N30, N31, N32, N33Valve for fuel dosage N290Fuel pressure regulating valve N276 Solenoid valve for charge pressure control N75 Intake manifold flap motor V157Engine control unit J623Throttle valve module J338 Exhaust gas recirculation valve N18Exhaust gas recirculation cooler change-over valve N345Pump 2 for coolant circulation V178Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Lambda probe heater Z19Automatic glow period control unit J179 Glow plugs Q10, Q11, Q12, Q13SP67_54GB41Engine managementThe engine managementThe Engine Management System of the 2.0 ltr. TDI engine with Common Rail injection system is the EDC 17 Electronic Diesel Control of the company Bosch. The EDC 17 Engine Management System is a further development of the EDC 16. Compared to the EDC 16, it differs by an increased calculating performance and a larger memory capacity. The EDC 17 Engine Management System offers in addition the possibility to integrate regulation functions for future technologies.SP67_55Control units in CAN data busInformation is transmitted via the CAN data bus between the control units.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP67_56Legend J104 - ABS/ESP control unit J217 - Automatic gearbox control unit J234 - Airbag control unit J285 - Control unit in the dash panel insert J527 - Steering column electronics control unit J533 - Databus diagnostic interface J623 - Engine control unit42GBThe exhaust turbochargerOn the 2.0 ltr. TDI engine with Common Rail injection system, the charge pressure is produced by a turbocharger with adjustable turbine vanes. The compression of the suctioned air is influenced by adjusting the guide vanes. This has the advantage that an optimal charge pressure is achieved over the entire speed range and thus a good combustion. The adjustable guide vanes enable a high torque in the lower speed range and a good start-up behaviour while in the upper speed range, they ensure a low fuel consumption and low exhaust emissions. The guide vanes are adjusted via a linkage through vacuum.Position sender for charge pressure regulator G581Exhaust turbochargerFlow damperFlow damperSP67_57A flow damper is installed in the charge air path behind the output of the turbocharger. It has the task to reduce disturbing noises from the turbocharger.Resonance volumeCharge air of turbochargerSP67_58Structure and function The charge air produces air oscillations in the At full engine power (e.g maximum acceleraresonance volume of the flow damper. These ostion), the turbocharger must quickly build up the cillations have approximately the same frequency necessary charge pressure. The turbine and as the noises of the charge air. The disturbing compressor wheel quickly reaches its maximum noises are minimised by the interaction of the speed, which can lead to flow interruptions in the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted sound waves of the charge air and the air oscilair flow. Disturbing noises may result from this, unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability information this document. Copyright by ŠKODA A. S.� lations of from theinresonance volumes of AUTO the flow which resonate in the charge air path. with respect to the correctness damper.GB43Engine managementCharge pressure sender G31/ Intake air temperature sender G42The charge pressure sender G31 and the intake air temperature sender G42 are integrated in one component and are located in the intake manifold.Charge pressure sender G31 Use of signal The current air pressure is detected in the intake manifold by the signal of the charge pressure sender. The engine control unit requires the signal for the control of the charge pressure. Effects of failure There is no alternative function if the signal fails. The charge pressure control is switched off and the engine performance is considerably reduced. The particle filter cannot be actively regenerated.Charge pressure sender G31/ Intake air temperature sender G42Intake air temperature sender G42 The signal of the intake air temperature sender uses the engine control unit for the control of the charge pressure. As the temperature influences the density of the charge air, the signal is used by the engine control unit as a correction value.Charge air coolerSP67_59Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�44GBPosition sender for charge pressure regulator G581The position sender for charge pressure regulator is integrated in the vacuum unit of the turbocharger. It enables the engine control unit to detect the position of the guide vanes of the turbocharger. Use of signal The signal of the sensor transmits the information regarding the current position of the guide vanes of the turbocharger to the engine control unit. Together with the signal of the charge pressure sender G31, the condition of the charge pressure control can therefore be determined. Effects of failure If the signal of the position sender for charge pressure regulator fails, the signal of the charge pressure sender and the engine speed are used in order to determine the position of the guide vanes of the turbocharger. The exhaust gas warning lamp K83 lights up in the dash panel insert.Position sender for charge pressure regulator G581Changeover valve for radiator of exhaust gas recirculation N345The exhaust gas recirculation cooler is switched on depending upon the coolant temperature. For as long as the coolant goes below the temperature of 37°C, the cooler remains off. Thus, the engine and the diesel particle filter reach their Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted operating temperature exhaust unless authorised by ŠKODA AUTO quicker. A. S. ŠKODA The AUTO A. S. does not gas guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� cooler is switched on as of a coolant temperature of 37°C. The changeover valve for cooler of exhaust gas recirculation is an electro pneumatic valve. It supplies the vacuum unit of the exhaust gas recirculation cooler with the required vacuum for operating the bypass flap. Effects of failure If the changeover valve for cooler of exhaust gas recirculation fails, the bypass flap can no longer be operated by the vacuum unit of the exhaust gas recirculation cooler. The bypass flap remains open and therefore the exhaust gas recirculation is active. Thus, there is a delay in reaching the operating temperature of the engine and the diesel particle filter.GBSP67_60Changeover valve for radiator of exhaust gas recirculation N345SP67_6145Engine managementThe diesel particle filter systemBeside the internal engine measures, the soot particle emissions are reduced in addition by a diesel particle filter on the 2.0 ltr. TDI engine with Common Rail injection system. The diesel particle filter is located together with the oxidation catalytic converter in one housing. It is positioned near the engine in order to quickly reach the operating temperature.Lambda probe G39 Exhaust pressure sensor 1 G450 Connection for exhaust pressure sensor G450 Exhaust gas temperature sender 4 G648 Exhaust gas temperature sender 3 G495SP67_62System overviewSP67_63Legend 1 2 3 4 5 6 - - - - - - Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Control unit in dash panel insert J285 Engine control unit J623 Air mass meter G70 Diesel engine Exhaust gas temperature sender 1 G235 Turbocharger7 - 8 - 9 - 10 - 11 - 12 - Lambda probe G39 Oxidation catalytic converter Diesel particle filter Exhaust gas temperature sender 3 G495 Exhaust pressure sensor 1 G450 Exhaust gas temperature sender 4 G64846GBStructure The diesel particle filter and the oxidation catalytic converter are installed separately from each other in the same housing. The oxidation catalytic converter is therefore positioned in direction of flow upstream of the particle filter.Lambda probe G39Oxidation catalytic converter Exhaust gas temperature sender 3 G495Exhaust currentDiesel particle filterExhaust gas temperature sender 4 G648Connection for exhaust pressure sensor G450SP67_64The structure of the upstream oxidation catalytic converter combined with the Common Rail injection system, offers the following advantages: - A quick temperature increase of the exhaust gas is achieved through the arrangement of the oxidation catalytic converter. Thus, the operating temperature of the diesel particle filter is quickly reached. - In the trailing throttle, a strong cooling of the diesel particle filter is avoided through the drawn-in cold Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not acts guarantee or a accept any liability air. In this case, the oxidation catalytic converter as temperature accumulator of which the with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� warmth is led to the particle filter by means of the exhaust flow. - During the regeneration procedure, the temperature of the exhaust gas can be regulated more precisely compared to the catalytically coated diesel particle filter. The exhaust gas temperature sender 3 (G495) detects the exhaust gas temperature directly upstream of the particle filter. Therefore the fuel quantity of the post injection, which ensures the increase of the exhaust gas temperature during the regeneration procedure, can be calculated accurately.GB47Engine managementRegeneration In order for the particle filter to not get clogged with soot particles and impaired in its function, it must be regenerated regularly. During the regeneration procedure, the soot particles collected in the particle filter are burned (oxidised). The regeneration of the particle filter is carried out in the following steps: - Passive regeneration - Heating phase - Active regeneration - Regenerating drive by the driver - Service regeneration Passive regeneration During the passive regeneration, the soot particles are continuously combusted without interference of the engine control. This occurs mainly during high engine load at exhaust gas temperatures of 350 °C – 500 °C. The soot particles are therefore converted into carbon dioxide through a reaction with nitrogen dioxide.Heating phase In order to quickly heat up a cold oxidation catalytic converter and a particle filter, thus bringing them to their operating temperature, a targeted post injection is initiated by the engine management after the main injection. The fuel injected during the post injection increases the temperature level of the combustion in the combustion chamber. The developing heat thereby is diverted into the exhaust gases and flows through the exhaust gas tract to the oxidation catalytic converter as well as to the particle filter and heats them up. The heating phase ends as soon as the operating temperature of the Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted oxidation catalytic converter and the particle filter is reached for a specific period of time. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�48GBActive regeneration The exhaust gas temperatures are too low for a passive regeneration of many various operating conditions (e.g many cold starts). Because no more soot particles can be passively removed, it leads to a soot accumulation in the filter. As soon as there is a certain soot load in the filter, an active regeneration is initiated by the engine control. The soot particles are burned into carbon dioxide at an exhaust gas temperature of 550 up to 650°C. Function of the active regeneration The soot load of the particle filter is calculated by two preprogrammed loading models, which are stored in the performance map of the engine control unit. One of the load models is determined from the control profile of the user as well as from the signals of the exhaust gas temperature sensors and the lambda probe. A further soot load model is determined from the flow resistance of the particle filter. It is calculated from the signals of the exhaust pressure sensor 1 G450, the exhaust gas temperature sensors and the air mass meter G70.Exhaust pressure sensor 1 G450 Exhaust gas temperature sender 3 G495 Lambda probe G39Engine control unit J623Air mass meter G70Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP67_65Oxidation catalytic converterDiesel particle filterGB49Engine managementMeasures of the engine control unit for the increase of the exhaust gas temperature during the active regeneration. - The intake air supply is regulated by the throttle valve.SP67_66- The exhaust gas recirculation is switched off in order to increase the combustion temperature and the oxygen share in the combustion chamber.SP67_67- Shortly after a "late" main injection, the first post injection is initiated in order to increase the combustion temperature.SP67_68- Late after the main injection, a further post injection is initiated. During this second post injection, the fuel does not burn in the cylinder yet it evaporates in the combustion chamber.SP67_69- The unburned hydrocarbons of this fuel vapor oxidise (burn) in the oxidation catalytic converter. The developing heat is carried by the air flow to the particle filter and ensures an increase of the exhaust gas temperature, of approx. 620 °C, upstream of the particle filter.SP67_70- In order to calculate the injection quantity of Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted the late post injection, the engine controlunless unitauthorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� uses the signal of the exhaust gas temperature sender 3 G495.SP67_71- During the regeneration procedure, the charge pressure is adapted so that the torque does not change noticeably.SP67_7250GBRegenerating drive by the driver A sufficiently high exhaust gas temperature, needed to regenerate the filter, cannot be reached during very short-distance traffic. If the loading condition of the particle filter has reached a limit value, the diesel particle filter warning lamp lights up in the dash panel insert. This signal means that the driver is requested to carry out a regenerating drive. Thus, the vehicle must be driven over a short period of time with increased speed in a certain speed range so that an adequately high exhaust gas temperature is reached and the operating conditions for a successful regeneration remain the same over this period of time.The precise information regarding the driveability when the diesel particle filter warning lamp lights up, can be found in the user manual of the vehicle.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Service regeneration If the regenerating drive which is carried out by the driver is not successful and the loading condition of the diesel particle filter has reached the highest possible percentage value, the glow period warning lamp additionally lights up with the diesel particle filter warning lamp. The text "engine fault workshop" is shown in the display of the dash panel insert. Thus the driver must go to the nearest workshop. In order to avoid damage to the particle filter, in this case the active regeneration of the diesel particle filter is blocked in the engine control unit. The particle filter can only be regenerated in the workshop by a service regeneration using the diagnostic unit VAS 505x.GB51Engine managementRegeneration stages of the 2.0 ltr. TDI engine with Common Rail injection systemReplacement of the filterLoad in gramsTimeSP67_73Increase of soot load The course of a successful regeneration in the respective step passive regeneration active regeneration Regenerating drive by the driver