TECHNICAL DOCUMENTATION
SSP 068 1,4 CAXC 92kW TSI petrol engine with turbocharging

This PDF is currently unavailable.
Read document text
Service1.4 ltr./92 kW TSI petrol enginewith turbocharging68Self-study programmeMaximum force for minimum fuel consumption - these are the main highlights of the 1.4 ltr. TSI engine. By way of the downsizing concept, turbocharging and direct fuel injection, the customer's demands were met and an engine with better driving dynamics and lower fuel consumption was developped.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The 1.4 ltr. TSI engine is the first engine of Škoda vehicles which operates according to the downsizing concept. The basic idea of the downsizing concept is to reduce the displacement, however not to impair the engine performance. The efficiency stage of the engine is increased by reducing the displacement because the friction losses are decreased in this way. Furthermore, the engines have a lower overall weight and therefore also a reduced rotating mass. The engines which operate according to the downsizing concept must therefore only move a reduced mass which results in a lower fuel consumption and at the same time lower exhaust emissions.2GBContentsIntroduction Engine mechanical components The cylinder block The cylinder head The crank assembly The intake system The intake manifold with the charge air cooler The single-stage supercharging with exhaust turbocharger The cooling systems The charge air cooling The fuel system Injection valves High-pressure fuel pump Engine management The system overview The sensors The actuators The function diagram Remarks 4 6 6 7 8 9 10 12 16 17 19 20 21 24 24 27 30 32 34You will find the instructions for the installation, removal, repair, diagnosis as well as the detailed user information in the repair manual, the diagnosis unit VAS 505x, in the onboard literature and the ELSA system. The time for going to press was on the 07/2008. The brochure is not subject to an update.GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�3IntroductionTechnical highlightsFor the 1.4 ltr. TSI engine, the supercharging is carried out with an exhaust turbocharger which is specifically designed to reach a high torque in the lower speed range. A further particularity is the liquid-cooled charge air cooler which is integrated in the intake manifold. Additionally, the intake manifold flap switch is no longer fitted due to constructive measures on the suction channel and at the pistons.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP68_36Technical highlights- - - - - - - 4-valve technology Grey cast iron-cylinder block Homogeneous mode (lambda 1) High-pressure laminator Double injection catalytic converter heating Exhaust turbocharger with wastegate Plastic intake manifold with integrated liquid-cooled charge air cooler - maintenance-free chain drive - Duo-centric oil pump - continuous inlet camshaft adjustment - Intake manifold without adjustable regulating flaps - Two-circuit cooling system - fuel system regulated as needed - High-pressure fuel pump with integrated pressure regulator valve4GBTechnical data Engine code letters Design Number of cylinders Valves per cylinder Displacement in cm3 Bore in mm Stroke in mm Compression ratio max. power output max. torque Engine management Fuel Exhaust after treatment Emission standard CAXC Inline engine 4 4 1390 cm3 76.5 mm 75.6 mm 10 : 1 92 kW at 5000 min-1 200 Nm at 1500 - 4000 min-1 Bosch Motronic MED 17.5.20 Super Unleaded with RON 95 or 91 – low reduction of the performance parameters Main catalytic converter, lambda control EU4 plusTorque and power output diagram100 90 80 70 P (kW) 60 50 40 30250 225 200 175 M (Nm) 150 125 100 7520 by copyright. Copying for private or commercial purposes, in part50 Protected or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� 10 25010002000 3000 4000 5000 6000 7000 n (min-1)SP68_01GB5Engine mechanical componentsThe cylinder blockThe cylinder block is made out of cast iron with flake graphite. This ensures a sufficient firmness in reference to high pressures which occur in the TSI engines. The increased firmness of the cylinder block, made out of cast iron with flake graphite, enables the use of a crankshaft with higher rigidity in comparison to the block made out of diecast aluminium.Cylinder tube Internal wall of the cylinder blockSP68_03The cylinder block is designed as a so-called open-deck (open design), i.e there are no partitions between the internal wall of the cylinder block and the cylinder tube. Advantages of this design:Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�- The air bubble formation is reduced, which can directly cause problems with the ventilation and cooling of the two-circuit cooling system. - When using the screw connection between the cylinder head and the cylinder block, the separation of the cylinder liner from the cylinder block leads to a less and more uniform deformation of the cylinder bush as was the case for the closed design with partitions. Thus, the oil losses are reduced because the piston rings adapt better to this deformation.6GBThe cylinder headDue to constant development of the components for combustion engines as well as the combustion procedure itself, the intake manifold switchover flap was not needed. However, in order to obtain a strong roller-shaped air flow in the combustion engine, the inlet duct is designed flatter. A tear-off edge at the seating of the inlet valves ensures a purposeful roller-shaped air flow across the upper edge of the valve plate into the combustion chamber.Inlet camshaftCamshaft housingInlet ductCylinder headTear-off edgeSP68_09Camshafts, camshaft housingOutlet valvesBy using the quadruple cams for the drive of On the basis of the lower exhaust gas the high-pressure fuel pump, the cam stroke is temperatures, complete stem valves without shortened. Thus, the diameters of the bearings sodium filling are installed. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted for the camshafts were reduced. The camshaft unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� housing is now a more compact design resulting in weight savings.GB7Engine mechanical componentsThe crank assemblyThe crank assembly consists of the following parts: Crankshaft, connecting rods, bearing shells, piston and piston pin.Piston Piston pinGraphite coating of the piston shellConnecting rodCrankshaftSP68_04Piston The pistons are diecasted from aluminium alloy. The piston crowns are provided with indentations of the combustion chamber which have an aerodynamic edge, causing a strong roller-shaped air flow of the suctioned air and therefore ensuring a good mixture preparation. The cooling of the pistons is performed by means of the oil nozzles which inject the oil onto the outlet sides of the piston. The injection nozzles open at a pressure of 2 bar. The crankshaft The friction of the piston was reduced through the graphite coating of the piston shell. In view of the high pressures which occur during the combustion, the diameter of the piston bolt is 19 mm.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Connecting rodsDue to the high mechanical stress, a forged crankshaft with high rigidity is used for the 1.4 ltr. TSI engine.The connecting rods are separated by fractures during the production while the mutual fitting together of both parts of the connecting rods is ensured and a good frictional connection is achieved. At the same time this method helps to lower the costs of production.8GBThe intake systemThe intake system extends from the air filter via the exhaust turbocharger, the throttle valve module and the intake manifold up to the inlet valves. It is designed in the most compact way, in order to improve the response mode of the exhaust turbocharger already at low speeds. Two pressure sensors with intake air temperature senders are installed in the intake system. They are located in front of the throttle valve module and at the intake manifold behind the charge air cooler.Exhaust turbocharger Intake manifold with charge air coolerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Air filterIntake manifold pressure sender G71 with intake air temperature sender G42 Throttle valve module J338Charge pressure sender G31 with intake air temperature sender G299SP68_05GB9Engine mechanical componentsThe intake manifold with the charge air coolerOn the basis of the compression of the suctioned fresh air by the exhaust turbocharger, the pressure and therefore the intake air temperature increase greatly. However, in order to achieve a relatively good filling the charge air is cooled. This happened to the previously charged FSI engines via an air charge air cooler at the front end. A liquid-cooled charge air cooling is used on the 1.4 ltr. 92kW TSI engine. For this reason, a coolant-operated charge air cooler is installed in the intake manifold. The compressed and thus warmed up charge air flows through the liquid-cooled charge air cooler, where a majority of its warmth is delivered to the charge air cooler and onwards into the inlet ducts. The coolant is pumped from a pump for coolant circulation V50 to the charge air cooler. Subsequently, the warmed up coolant flows again to the additional water cooler for charge air cooling at the front end. The charge air cooling system is an independent cooling circuit in which the exhaust turbocharger is also integrated.air cooler through which the coolant flows Coolant return flowcooled charge airProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP68_06warmed up charge airCoolant feedPump for coolant circulation V50Cooled charge air Warm charge airCold coolant (feed) Warm coolant (return flow)10GBThe liquid-cooled charge air cooler The liquid-cooled charge air cooler slides into the intake manifold and is attached with six screws. A sealing ledge is located on the reverse side of the liquid-cooled charge air cooler. This sealing ledge is used for the sealing of the charge air cooler to the intake manifold and as a support of the charge air cooler.Liquid-cooled charge air coolerPay attention to the correct seating of the sealing ledge when installing the liquid-cooled charge air cooler. If it is not correctly installed, this results in vibrations, the charge air cooler cracks and becomes leaky.Intake manifoldSP68_07Sealing ledgeFastening of the charge pressure pipe The charge pressure pipe is positioned on the exhaust turbocharger and on the throttle valve module. It is clipped on the throttle valve module with an adapter and screwed on the exhaust turbocharger using a mounting bracket.Mounting bracketProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Charge pressure pipeAdapterSP68_08GB11Engine mechanical componentsThe single-stage supercharging with exhaust turbochargerAs on most of the charged engines, the supercharging is solely carried out with an exhaust turbocharger on the 1.4 ltr. TSI engine. The exhaust turbocharger was designed for a high torque in the lower speed range and an advantageous fuel consumption, as only a slight charge pressure is necessary to reach its maximum power.Exhaust turbochargerSP68_02The exhaust turbocharger moduleThe exhaust turbocharger and the exhaust maniExhaust turbocharger module fold form a module. In order to keep the temperatures low at the shaft mounting after switching off the engine, it is integrated in the cooling circuit of Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted the charge air cooling. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� In addition, the shaft mounting is connected to the oil circulation system for lubricating and cooling. Furthermore, the circulating air valve for exhaust turbocharger and a pressure capsule for the charge pressure control with the wastegate is located on the exhaust turbocharger module.Oil connectionsCirculating air valve for turbocharger N249Coolant connectionsSP68_10Pressure capsule for charge pressure controlSolenoid valve for charge pressure control N7512GBThe exhaust turbocharger module The exhaust turbocharger is designed for dynamics and fuel consumption. This means that a relatively high torque is already available in the frequently used lower speed range. This is achieved by keeping the inertia of the moving parts in the turbocharger as low as possible. This complete design leads to the fact that 80% of the maximum torque is reached at 1250 rpm and 100% as of 1500 rpm. The material of the exhaust manifold is designed for 950°C.Rotor group with bearing housingWastegate flap Circulating air valve for turbocharger N249Pressure capsule for charge pressure controlSP68_11The outer diameter of the turbine wheel is 37 mm The wastegate flap of 26 mm and also the diamand the outer diameter of the compressor wheel eter of the diaphragm in the pressure capsule Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted is 41 mm. Only a minor mass of the exhaust must for charge pressure control are designed for unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� be moved using this compact design. a lower actuating pressure. Therefore, a higher The exhaust turbocharger produces more quickly charge pressure can be adjusted at low speeds the required charge pressure. for a good dynamic and a slight charge pressure in the partial load range for an advantageous consumption.GB13Engine mechanical componentsSchematic overview of the exhaust turbocharging The largest difference to the previously charged FSI engines is that the charge air is cooled in the suction pipe via a liquid-cooled charge air cooler.liquid-cooled charge air coolerIntake manifoldIntake manifold pressure sender G71 with intake air temperature sender G42Throttle valve module J338 Exhaust manifold Solenoid valve for charge pressure control N75 Pressure capsule for exhaust turbocharger Charge pressure sender G31 with intake air temperature sender G299Circulating air valve for exhaust turbocharger N249Catalytic converter Exhaust gas Wastegate flap Exhaust turbochargerAir filter Fresh airSP68_12The fresh air is suctioned via the air filter and compressed by the compressor wheel of the exhaust turbocharger. The maximum charge pressure is definitely 1.8 bar.The charge pressure control is mainly carried out by the signals of the charge pressure sender G31 and the intake air temperature sender G299.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�14GBCharge pressure control The charge pressure control regulates the air mass which is compressed by the exhaust turbocharger. For a relatively precise control, two charge pressure senders with intake air temperature senders are combined in the intake system. Charge pressure sender G31 with intake air temperature sender G299 The charge pressure is controlled with the signals of the charge pressure sender. The signals from the intake air temperature sender G299 serve as a correction value for the charge pressure, as the temperature influences the density of the charge air. In addition, the charge pressure is down-regulated for the protection of the components if the temperatures are too high. Intake manifold pressure sender G71 with intake air temperature sender G42 The air mass in the intake manifold behind the charge air cooler is calculated by the engine control unit using the intake manifold pressure sender G71 with the intake air temperature sender G42. Depending on the calculated air mass, the charge pressure is adapted according to the performance map and increased to a definite pressure of 1.8 bar.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Charge pressure sender G31 with intake air temperature sender G299SP68_13Intake manifold pressure sender G71 with intake air temperature sender G42Ambient pressure sender The ambient pressure sender in the engine control unit measures the surrounding air pressure. This is used as correction value for the charge pressure control, as the density of the suctioned air decreases with increasing height and vice versa.Solenoid valve for charge pressure control N75 The solenoid valve for charge pressure control N75 is controlled with clock pulses by the engine control unit and switches the control pressure in the pressure capsule for exhaust turbocharger. The wastegate flap is operated via this and leads one part of the exhaust gases past the turbine into the exhaust system. Thus, the turbine output and the charge pressure are controlled.GB15Engine mechanical componentsThe cooling systemsThe 1.4 ltr. 92kW TSI engine has two cooling systems which are independent of each other. One for cooling the engine as always and another one for cooling the charge air. Both systems are separated from each other except at two connection points. A common expansion reservoir can be used by means of these connection points. The temperature difference between the engine cooling system and the charge air cooling system can be up to 100°C. Particularities of the engine cooling system - Two-circuit cooling system for various coolant temperatures in the cylinder head and the cylinder block - Coolant distributor housing with one-stage thermostats Particularities of the charge air cooling system - Pump for coolant circulation V50 - liquid-operated charge air cooler within the suction pipe - Cooling of the exhaust turbochargerCharge air cooler in suction pipeExpansion reservoirPump for coolant circulation V50Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information Check valve in this document. Copyright by ŠKODA AUTO A. S.�Th non-return valve closes depending upon pressure and prevents that the warmer coolant from the engine cooling system is forced into the charge air cooling system.Throttle The throttle minimises the coolant exchange between the engine and the charge air cooling system.Exhaust turbochargerAdditional water cooler charge air systemSP68_14The ventilation takes place either with the cooling system filling device VAS 6096 or via the targeted function "fill up and bleed cooling system". Please observe the instructions in ELSA.16GBThe charge air coolingA liquid-cooled charge air cooling is used for the first time on the 1.4 ltr. 92kW TSI engine. Thereby the charge air is cooled in the suction pipe by a charge air cooler through which the coolant flows. The charge air system, which includes the exhaust turbocharger and the injection valves, was therefore reduced to a mere 4.8 ltr. The exhaust turbocharger must compress a lower quantity and the required charge pressure is reached more quickly. In order to greatly cool down the charge air, the pump for coolant circulation V50 is controlled according to use. It suctions the coolant from the additional water cooler at the front end and pumps it to the charge air cooler in the suction pipe and to the exhaust turbocharger. The temperature difference between the air behind the charge air cooler and the outside temperature is approx. 20°C to 25°C at high load demand.Exhaust turbocharger Additional water cooler charge air systemProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP68_15Pump for coolant circulation V50liquid-cooled charge air coolerGB17Engine mechanical componentsThe pump for coolant circulation V50 As already mentioned, the pump for coolant circulation V50 is controlled according to use. It suctions the coolant from the additional water cooler for charge air and delivers it to the charge air cooler in the suction pipe and to the exhaust turbocharger.to the charge air cooler and exhaust turbochargerPump for coolant circulation V50from the additional water coolerSP68_16The charge air coolerCharge air coolerThe charge air cooler consists of many aluminium plates through which a pipe with coolant is led. The warm air flows past the plates and by doing this delivers the heat to them. The plates in turn give off the heat to the coolant. SubsequentProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted ly, the coolant is pumped back to by the additional unless authorised ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� water cooler at the front with end where it then cools down.Coolant feedCoolant return flowSP68_17The exhaust turbocharger During engine operation, the cooling of the turbocharger is mainly carried out by the engine oil. The coolant is only delivered to the turbocharger depending upon use. If the warm engine is switched off, the pump for coolant circulation is controlled for up to 480 seconds. Thus, a formation of vapor bubbles is prevented in the cooling circuit of the turbocharger.Coolant return flowExhaust turbochargerCoolant feedSP68_1018GBThe fuel systemThe fuel system regulated as neededThe fuel system of the 1.4 ltr. TSI engine, which is regulated as needed, has been taken over to a large extent by the existing charged FSI engines. The electrical fuel pump as well as the high-pressure fuel pump always deliver the fuel the engine needs at a precise moment. Thus, the electrical as well as the mechanical drive power output is as low as possible and fuel is saved. High-pressure fuel system The high-pressure fuel pump is driven via a quadruple cam with 3 mm stroke at the inlet camshaft. The pressure regulator valve is installed in the high-pressure fuel pump. Thus, the leakage line from the fuel distributor to the low pressure fuel system is no longer needed. The actuation concept of the high-pressure fuel pump is laid out in such a way that the fuel pressure regulating valve N276 is closed in the de-energized condition and fuel is delivered into the fuel distributor pipe. Therefore, a quick pressure build-up is possible during cold start.Engine control unit J623Fuel pressure sender G247High-pressure fuel pumpFuel distributorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP68_18Quadruple pump camsInjectors for cylinder 1-4 N30-N3350 - 100 barDuring the overrun cut-off, the fuel pressure can also increase to above 100 bar when heating up.GB19The fuel systemInjection valvesThe jet image of the 6-hole injectors was optimized. The jet image of the high-pressure injection valves was up to now circular or oval. Now the jets are arranged in such a way that a wetting of the piston crown can be avoided to the greatest extent.previous jet imageoptimized jet imageInjection valveInjection valveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP68_20SP68_19Wetting of the crownhigher located injection jet20GBHigh-pressure fuel pumpThe quantity-controlled single cylinder high pressure fuel pump is screwed onto the camshaft housing. In the de-energized condition, the high-pressure fuel pump delivers the fuel into the high-pressure fuel system.SP68_21High-pressure fuel pumpPressure regulator valve The pressure regulator valve is integrated with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� in the high-pressure fuel pump and protects the components of the fuel system against damage, which could be caused by the high pressure during thermal expansion of the fuel. It is a mechanical valve and opens at a fuel pressure of 140 bar. The opened valve discharges the surplus fuel from the high pressure side to the low pressure side.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitySP68_22Pressure regulator valveGB21The fuel systemFunction of the high-pressure fuel pump Fuel suction stroke During the suction stroke, a suction effect arises through the downward movement of the pump piston. By doing so, the inlet valve is opened and the fuel is suctioned into the pump space. In the last third of the downward movement of the pump piston, the fuel pressure regulating valve N276 is energized. Thus, the inlet valve also remains opened at the start of the upward movement for the fuel return delivery.Fuel pressure regulating valve N276SP68_23Pump spacePump plungerInlet valveFuel return delivery In order to adapt the fuel quantity to the actual consumption, the inlet valve also remains opened at the start of the upward movement of the pump piston. The surplus fuel is directed back into the low pressure area by the pump piston. Thus, the developing pulsations are compensated for by the pressure dampers in the low pressure area of the high-pressure fuel pump.Pressure damperSP68_24Pump plungerInlet valve22Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GBFuel delivery stroke The fuel pressure regulating valve N276 is no longer energized for the calculated start of the delivery stroke. Therefore, the inlet valve is closed due to the increasing pressure in the pump space and the force of the valve needle spring. Pressure builds up in the pump space through the upward movement of the pump piston. If the pressure in the pump space is greater than in the fuel distributor, the outlet valve opens. The fuel is pumped to the fuel distributor.Valve needle springSP68_25Exhaust valveInlet valveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB23Engine managementThe system overviewSensorsIntake manifold pressure sender G71 with intake air temperature sender G42 Charge pressure sender G31 with intake air temperature sender G299 Engine speed sender G28Hall sender G40 Throttle valve module J338/ Throttle valve drive angle sender 1 G187/ Throttle valve drive angle sender 2 G188 Accelerator pedal position sender G79/ Accelerator pedal position sender 2 G185 CAN data bus drive Data bus diagnostic interface J533 Self diagnosis connectionGBClutch position sender G476 Brake pedal position transmitter G100 Fuel pressure sender G247 Knock sensor 1 G61 Coolant temperature sender G62Radiator outlet coolant temperature sender G83 Lambda probe G39Lambda probe after catalytic converter G130 Additional input signalsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�24ActuatorsFuel pump control unit J538/ Fuel pump G6 Injectors for cylinder N30-33 Engine control unit J623 with ambient pressure sender Ignition coils 1 - 4 with output stages N70, N127, N291, N292Throttle valve module J338/ Throttle valve drive G186 Current supply relay for engine components J757Fuel pressure regulating valve N276Activated charcoal filter system solenoid valve N80Control unit in dash panel insert J285Lambda probe heater Z19Lambda probe heater after catalytic converter Z29CAN data bus dash panel insertCamshaft adjustment valve N205 Circulating air valve for turbocharger N249 Solenoid valve for charge pressure control N75Fault indicator lamp for electric power control K132Exhaust emission warning lamp K83Additional coolant pump relay J496/ Pump for coolant circulation V50 Additional output signalsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted SP68_26 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB25Engine managementEngine managementThe engine management Bosch Motronic MED 17.5.5 is used for the 1.4 ltr. TSI engine. The Bosch Motronic MED 17.5.5 is the follow-up engine management to the Bosch Motronic MED 9. This innovative engine management differs from the Bosch Motronic MED 9 in the following points: - quicker processor - Designed for snap-action Lambda probes - K-line does no longer exist - High-pressure lamination as of -30°CEngine control unit J623SP68_27The high-pressure laminationProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�By means of the new actuation of the highpressure fuel pump, a pressure of approx. 60 bar is very quickly built up and the high-pressure lamination is already possible as of -30°C. While doing so, the fuel is injected shortly before ignition. The temperatures prevailing at this stage in the cylinder and the high pressure provide a very good mixture preparation. Therefore, the fuel quantity needed for the start can be reduced and in particular the carbon dioxide emissions can decrease.SP68_2826GBThe sensorsCharge pressure sender G31 with intake air temperature sender 2 G299 The charge pressure sender G31 with intake air temperature sender G299 is screwed into the pressure pipe just before the throttle valve module J338. It measures the pressure and the temperature in this area.Use of signal The engine control unit regulates the charge pressure of the turbocharger by means of the signal for the charge pressure sender. The control occurs via the charge pressure control solenoid valve. The signal of the intake air temperature sender is needed: - for calculating a correction value for the charge pressure. Thus, the temperature influence on the density of the charge air is taken into account. - for the component protection. If the temperature of the charge air exceeds a certain value, the charge pressure is down-regulated. - for the actuation of the pump for coolant circulation. If the temperature difference of the charge air before and after the charge air cooler is less than 8 °C, the pump for coolant circulation is controlled. - for the plausibility check of the pump for coolant circulation. If the temperature difference of the charge air before and after the charge air cooler is less than 2°C, the pump could be defective. The exhaust emission warning lamp K83 is switched on. Effects of signal failureProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted If both senders fail, the turbocharger operation unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� is only actuated. The charge pressure is lower and the power decreases.SP68_29Charge pressure sender G31 with intake air temperature sender G299GB27Engine managementIntake manifold pressure sender G71 with intake air temperature sender G42 The intake manifold pressure sender G71 with intake air temperature sender G42 is located in the suction pipe behind the charge air cooler. It measures the pressure and the temperature in this area.Use of signal The engine control unit calculates the drawn in air mass from the signals and the engine speed. Furthermore, the signal of the intake air temperature sender is needed for the: - actuation of the pump for coolant circulation. If Intake manifold pressure sender G71 the temperature difference of the charge air bewith intake air temperature sender G42 fore and after the charge air cooler is less than 8 °C, the pump for coolant circulation is controlled. - plausibility check of the pump for coolant circulaProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted tion. If the temperature difference of charge unless authorised bythe ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� air before and after the charge air cooler is less than 2°C, the pump could be defective. The exhaust emission warning lamp K83 is switched on.SP68_30Effects of signal failure If the signal fails, the throttle valve position and the temperature of the intake air temperature sender G299 are used as a replacement signal. The turbocharger operation is only actuated.28GBThe fuel pressure sender, high pressure G247 The fuel pressure sender G247 is located on the side of the distributor below the intake manifold bottom part and is screwed into the fuel distributor pipe. It measures the fuel pressure in the high-pressure fuel system and transmits the signal to the engine control unit.Use of signal The engine control unit evaluates the signals and regulates the pressure in the fuel distributor pipe via the control valve for fuel pressure N276. In addition, if the fuel pressure sender detects that the nominal value can no longer be regulated, the control valve for fuel pressure is continuously open during the compression. Thus, the fuel pressure of the low pressure fuel system is reduced to 5 bar.SP68_31Fuel pressure sender, high pressure G247Effects of signal failure If the fuel pressure sender fails, the control valve for fuel pressure is continuously open during the compression. Thus, the fuel pressure of the low pressure fuel system is reduced to 5 bar. The engine torque and the power are drastically reduced.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB29Engine managementThe actuatorsThe fuel pressure regulating valve N276 The fuel pressure regulating valve is located at the side of the high-pressure fuel pump.Task It has the task to make the required fuel quantity available in the fuel distributor pipe.Effects of failure The regulating valve is closed when deenergized. This means that the fuel pressure increases when the regulating valve fails until the pressure regulator valve in the high-pressure fuel pump opens at approx. 140 bar. The engine management adapts the injection periods to the high pressure and the engine speed is limited to 3000 rpm.High-pressure fuel pumpSP68_32Fuel pressure regulating valve N276The fuel pressure must be reduced before opening the high-pressure fuel system. Up to now the connector for the fuel pressure regulating valve could be unplugged, the regulating valve was de-energized when opened and the fuel pressure was reduced. On the 1.4 ltr. 92kW TSI engine the regulating valve is de-energized when closed, because of this the fuel pressure is no longer reduced if the connector is unplugged. Therefore the function "reduce fuel high pressure" is integrated in the targeted functions. With which the regulating valve is opened during the engine running and the pressure is reduced. Please observe the instructions in ELSA.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�30GBAdditional coolant pump relay J496 The additional coolant pump relay is located in the engine compartment on the electric box. Task The high work currents for the pump for coolant after-running V50 are switched via the relay.Effects of failure If the relay fails, the pump for coolant afterrunning V50 can no longer be actuated.SP68_33Additional coolant pump relay J496Pump for coolant circulation V50 The pump for coolant circulation is screwed onto the cylinder block below the intake manifold. It is a component part of an independent cooling circuit. Task The pump for coolant after-running delivers coolant from an additional cooler at the front end to the charge air cooler and to the exhaust turbocharger. It is actuated under the following conditions: - briefly after each engine start - continuously as of a torque demand of approx. 100 Nm - continuously as of a charge air temperature of 50°C in the intake manifold - as of a temperature difference of the charge air before and after the charge air cooler of less than 8°C - for 10 seconds each 120 seconds when engine is running in order to avoid a heat build-up in front of the exhaust turbocharger. - depending on the performance map for 0-480 seconds after switching off the engine in order to avoid a formation of vapor bubbles in the cooling circuit on the exhaust turbocharger.SP68_35Pump for coolant circulation V50Effects of failure If the pump for coolant after-running fails, this can lead to overheating. The pump is not directly checked by the self diagnosis. A fault in the cooling system is detected by a temperature comparison before and after the charge air cooler and the exhaust emission warning lamp K83 is switched on.GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�31Engine managementThe function diagramT94/79T94/62T94/74T94/84T94/57T60/32T94/68T94/13T60/67T94/51T94/14 T94/15T94/55T60/34T60/48T60/46T94/81T60/33T60/31T60/49T60/60T60/45T94/82T94/78T94/15T60/47T60/32T60/10T94/16A G G1 G6 G28 G31 G39 G40 G42 G61 G62 G71 G79 G83 G100 G130 Lambda probe after catalytic converter Battery G185 Accelerator pedal position sender 2 Fuel gauge sender G186 Throttle valve drive Fuel gauge G187 Throttle valve drive angle sender 1 Fuel pump G188 Throttle valve drive angle sender 2 Engine speed sender G247 Fuel pressure sender, high pressure Charge pressure sender G299 Intake air temperature sender 2 Lambda probe G476 Clutch position sender Hall sender Protected by copyright. Copying for private or commercial purposes, inJ104 part or in whole, is not permitted ABS control unit Intake air temperature sender unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability J271 Motronic supply relay, in electric box Knock sensor 1the correctness of information in this document. Copyright with respect to by ŠKODA AUTO A. current S.� J285 Control unit in the dash panel insert Coolant temperature sender Intake manifold pressure sender J496 Additional coolant pump relay Accelerator pedal sender J519 Onboard supply control unit Coolant temperature sender at radiator outlet J533 Databus diagnostic interface Brake pedal position transmitter J623 Engine control unit32T60/55GBT94/15T94/15T94/1T60/11T60/2T60/3T94/2T94/7T60/35T60/50T60/15T60/15T94/19T94/18T60/37T60/41T60/14T60/56T60/59T60/39T60/57T60/51T60/36T60/8T60/43T60/58T60/54T60/42J681 Voltage supply relay, tml. 15 N292 Ignition coil 4 with output stage N30-33 Injector, cylinder 1-4 P Spark plug connector N70 Ignition coil 1 with output stage Q Spark plugs N75 Charge pressure control solenoid valve S Fuse N80 Activated charcoal filter system solenoid valve V50 Pump for coolant circulation 1 1 Switch for cruise control system N127 Ignition coil 2 with output stage 2 Generator terminal DFM N205 Inlet camshaft timing adjustment valve 1 3 Radiator fan stage 1 N249 Circulating air valve for turbocharger Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA regulating AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability N276 Fuel pressure valve with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� N291 Ignition coil 3 with output stage Plus Earth Output signal Input signal CAN data busSP68_34GBT60/52T60/9T60/6T94/94T60/4T60/1T94/3T94/533RemarksProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�34GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB35List of Self-Study Programmes so far Title No. 1 Mono-Motronic 2 Central locking 3 Anti-Theft Alarm 4 Working with current flow diagrams 5 ŠKODA FELICA 6 ŠKODA-Vehicle safety 7 Principles of ABS not published 8 ABS-FELICIA 9 Immobilizer with transponder 10 Air conditioning in vehicles 11 Air conditioning FELICIA 12 1.6-ltr. engine with MPI 13 1.9-ltr. Naturally aspirated diesel engine 14 Power-assisted steering 15 ŠKODA OCTAVIA 16 1.9-ltr. TDI engine 17 OCTAVIA Convenience electronic system 18 OCTAVIA Manual gearbox 02K/02J 19 1.6-ltr./1.8-ltr. Petrol engines 20 Automatic gearbox - fundamentals 21 Automatic gearbox 01M 22 1.9-ltr. 50 kW SDI/1.9-ltr. 81 kW TDII 23 1.8-ltr. 110 kW turbo petrol engine 1.8-ltr. 92 kW petrol engine 24 OCTAVIA, CAN databus 25 OCTAVIA - CLIMATRONIC 26 OCTAVIA - Vehicle safety 27 OCTAVIA - 1.4-ltr. Engine and Gearbox 002 28 OCTAVIA - ESP 29 OCTAVIA - 4x4 30 Petrol engine 2.0-ltr. 85 kW/88 kW 31 OCTAVIA - Radio/navigation system 32 ŠKODA FABIA 33 ŠKODA FABIA - Vehicle electrics 34 ŠKODA FABIA - Power-assisted steering 35 Petrol engines 1.4-ltr. - 16V 55/74 kW 36 ŠKODA FABIA - 1.9-ltr. TDI Unit injection 37 5-Speed manual gearbox 02T and 002 38 ŠkodaOctavia - Model 2001 39 Euro-On-Board-Diagnosis 40 Automatic gearbox 01 41 6-Speed manual gearbox 02M 42 ŠkodaFabia - ESP 43 Exhaust emission 44 Extended maintenance interval 45 1.2-ltr. 3-cylinder petrol engines 46 ŠkodaSuperb; Presentation of the vehicle part I 47 ŠkodaSuperb; Presentation of the vehicle part II 48 ŠkodaSuperb; 2.8-ltr./142 kW V6 petrol engine 49 ŠkodaSuperb; 2.5-ltr./114 kW TDI V6 Diesel engine 50 ŠkodaSuperb Automatic gearbox 01V Title No. 51 2.0 ltr./85 kW Petrol Engine with balance shafttransmission and 2-stage switching intake manifold 52 ŠkodaFabia; 1.4-ltr. TDI engine with unit injection system 53 ŠkodaOctavia; Presentation of the vehicle 54 ŠkodaOctavia; Electrical Components 55 FSI Petrol engines; 2.0 ltr./110 kW and 1.6 ltr./85 kW 56 Direct manual gearbox 57 Diesel engine 2.0 ltr./103 kW TDI Unit injector 2.0 ltr./100 kW TDI Unit injector 58 ŠkodaOctavia; Chassis and electromechanical power-assisted steering 59 ŠkodaOctavia RS, Petrol Engine 2.0-ltr./147 kW FSI turbo 60 2.0 ltr./103 kW 2V TDI diesel engine; diesel particle filter system with additive 61 Satellite navigation systems in Škoda vehicles 62 ŠkodaRoomster; Presentation of the vehicle part I 63 ŠkodaRoomster; Presentation of the vehicle part II 64 ŠkodaFabia II; Presentation of the vehicle 65 ŠkodaSuperb II; Presentation of the vehicle part I 66 ŠkodaSuperb II; Presentation of the vehicle part Il 67 2.0 ltr./125 kW TDI diesel engine with Common Rail injection system 68 1.4 ltr./92 kW TSI petrol engine with turbochargingOnly intended for internal use in the Škoda-Organisation. All rights reserved. Subject to technical modification. GB S00.2002.68.20 CZ Technical status 07/08 © ŠKODA AUTO a.s. http://portal.skoda-auto.comProtected by copyright. Copying privateout or commercial purposes, in part or This paper was for made of chlorine-free unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guara bleached cellulose with respect to the correctness of information in this document. Copyright by68