TECHNICAL DOCUMENTATION
SSP 070 All-wheel drive with Haldex coupling Generation IV

This PDF is currently unavailable.
Read document text
Service70All-wheel drive with Haldex coupling Generation IVSelf-study programmeor commercial purposes, in part or in whole, is not permitted ŠKODA AUTO A. S. does not guarantee or accept any liability ation in this document. Copyright by ŠKODA AUTO A. S.�Since 2008, the four-wheel drive system has been implemented in all Škoda vehicles based on the Haldex Generation IV coupling . This new generation of the all-wheel drive clutch was incorporated for the first time in the ŠkodaOctavia II. The Haldex Generation IV coupling is exclusively electronically controlled, so that each random drive torque can build up independently of slip at any time. Thus, the distribution of the drive torque between the front and rear axle is variable and is dependent upon the driving style or the driving situation. The clutch can transfer up to 50% of the drive torque to the rear axle in the event of an extremely high wheel slip at the front axle or due to the current driving situation. The new generation of the Haldex coupling ensures an optimum transfer of the driving force onto the roadway.SP70_58Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�2GBContentsBrief The drive train of the all-wheel drive Th e angular gearbox The propshaft The rear flexible disc The centre joint The rear wheel drive The Haldex coupling in detail The Haldex Generation IV coupling The control unit for Haldex coupling J492 Control of the Haldex coupling The oil circuit Driving situations System overview Function diagram Service DiagnosisProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�4 6 7 8 8 8 9 10 10 17 18 18 20 22 23 24 24 24 26Function test of the Haldex coupling Service informationFor the instructions concerning the installation, removal, repair, diagnosis as well as the detailed user information, please refer to the ELSA system, the diagnosis unit VAS 505x and the onboard literature. The time for going to press was on the 01/2009. This brochure is not subject to update.GB3BriefIntroductionThe Haldex all-wheel drive clutch was first of all incorporated in the ŠkodaOctavia of the first generation in the 4x4 version. It is an electro-hydraulic multiple disc clutch, which enables the drive of individual axles to be regulated electronically. The Haldex coupling control unit takes into account, apart from slip, the dynamic driving conditions, speed and overrun or tractive operation. The first generation of Haldex coupling It was incorporated in the ŠkodaOctavia of the first generation in the 4x4 version. The second generation of Haldex coupling It was incorporated in the ŠkodaOctavia of the second generation in the 4x4 version as of model year 2004.SP70_01SP70_02Škoda vehicles have not been equipped with the third generation of Haldex coupling.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Function of the Haldex coupling Through a speed difference between the front and rear axle, the Haldex couplings of the first two generations produce a pumping action via a cam plate, fastening rollers and two parallel operating lifting pistons, which in turn builds up the actuating oil pressure. This oil pressure compresses the disc pack via a working piston. The transferred drive torque determines the high level of the abutting pressure. The pressure on the discs of the clutch is regulated by the suction and pressure valves through an electronically controlled valve and a control unit.4GBThe Haldex Generation IV couplingThe force transmission from the disc pack of the Haldex Generation IV coupling is similar inprinciple to the previous Haldex models. The oil pressure build-up is now produced by an electrical pump. The torque which must be transferred is determined by the control unit for Haldex coupling J492 by way of actuating the solenoid valve for controlling the opening degree of the coupling N373. Speed differences between the front and rear axle are no longer a prerequisite for the activation of the Haldex Generation IV coupling.Technical highlights- electro-hydraulically controlled multiple disc clutch - integrated in the rear wheel drive - simplified hydraulic circuit - pump control depending upon useSFlbThe advantages- clutch control depending upon driving style - faster torque build-up through pilot control SP70_03 - compatible with the electronic slip control systems (e.g ESP, ABS) Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted - independent of the driving situation unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB5The drive train of the all-wheel driveThe overview of the structureThe front wheels are conventionally driven via the front axle differential. At the same time, the torque is transferred from this differential to the propshaft via a flanged angular gearbox. It is connected to the Haldex coupling. Depending on the opening degree of the Haldex coupling, an appropriate driving torque is applied to the rear wheel drive.EngineAngular gearbox Propshaft Rear axle driveHaldex coupling Transmission Rear axle differentialFront axle differentialSP70_04Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�6GBThe angular gearboxThe angular gearbox increases the propshaft speed with a factor (gear ratio) of 1.6 (i.e. the speed of the propshaft is 1.6 x greater than the speed of the input shaft of the gearbox). Thus, the shaft can be of smaller diameter as it must transfer less torque. SFlbThe speed is then reduced again by the same factor in rear wheel drive mode.Output at right wheelInput of gearbox and output at left wheelOutput at propshaftSP70_05The power flowThe torque is transferred from the spur gear via the differential cage of the differential to the hollow shaft with crown wheel and to the drive pinion on the propshaft.of gearbox Differential cage Hollow shaftOutput at left wheelOutput at right wheelSP70_06 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Output at propshaftSpur gearDrive pinionCrown wheelGB7The drive train of the all-wheeldriveThe propshaftThe propshaft consists of two parts. The connection is via a centre joint. Flexible discs are installed for attaching to the angular gearbox and the Haldex coupling. A rotary vibration damper is put on the rear flexible disc (not separable). It reduces the transfer of engine vibrations via the rear axle drive to the body.Flexible disc Centre joint Flexible disc with rotary vibration damperDriving directionProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP70_07The rear flexible discThe rear axle drive and the propshaft are balanced when manufactured. For this reason, a balancing of the drive train in the vehicle is not needed.The centre jointThe centre joint is grouted and therefore cannot be separated. This enabled a more compact and easier design. The roller bellows are better protected.Roller bellowsRotary vibration damperSP70_08SP70_098GBThe rear wheel driveThe Haldex coupling is integrated in the rear wheel drive.Drive pinion of the rear axle driveCrown wheelDisc pack of the Haldex couplingRear axle differentialOil reservoir of Haldex coupling Drive shaftSP70_10Control unit for Haldex coupling J492Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB9The Haldex coupling in detailThe Haldex Generation IV couplingTask The Haldex coupling is installed between the propshaft and the rear wheel drive and regulates the transfer of the drive torque to the rear axle. It applies the required drive torque to the rear axle depending on the opening degree.StructureAccumulator Disc pack Oil filterPump for Haldex coupling V181Valve for controlling the opening degree of the coupling N373SP70_11Control unit for Haldex coupling J492The oil circuitMultiple disc clutch Valve for controlling the opening degree of the coupling N373for Haldex Protected by copyright. Copying for private or commercial purposes,Control in part or inunit whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does coupling not guarantee or accept any liability J492 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Accumulator Pump for Haldex coupling V181SP70_1210GBThe Haldex coupling can be divided into two groups from the perspective of the function system:The mechanical assembly groupDisc springNeedle bearingThrust washersSP70_13Working piston Needle bearing Drive hubDisc pack Clutch basketThe electro-hydraulic assembly group and the control unit for Haldex couping J492Valve for controlling the opening degree of the coupling N373Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP70_14Control unit for Haldex coupling J492 Accumulator Pump for Haldex coupling V181Oil filterGB11The Haldex coupling in detailThe mechanical assembly groupThe mechanical assembly group consists of three parts: - the multiple disk clutch - the working piston - the disc spring This entire assembly group establishes traction between the front and rear axle. If pressure is applied to the working piston, the disc pack is compressed. Depending on the contact pressure, the torque transferred to the rear axle is regulated (up to 2000 Nm).The multiple disc clutchThe multiple disc clutch consists of the drive hub, the disc pack and the clutch basket. The drive hub The drive hub is driven via the flange of the propshaft.Drive hub from the propshaftSP70_15 SP70_16The disc packSteel discThe disc pack consists of steel friction discs Friction disc and one thrust washer at the front and at the rear. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted The friction discs have internal teeth and are fitted onto the inner hub. The steel discs are connected to the clutch basket via their external toothing. The number of discs depends on the vehicle model.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP70_17Thrust washer Disc packSP70_1812GBThe clutch basket The clutch basket is connected to the drive pinion of the rear axle by means of a plugin toothing and transmits the drive torque to the drive pinion.Drive pinion of the rear axleSP70_20Clutch basketSP70_19Plug-in toothingThe working piston Structure The working piston is a ring piston. Task When operating the clutch, the pressure of the working piston is transferred to the disc pack via a needle bearing. The working piston does not turn. The disc pack in contrast rotates with the drive speed.SP70_21Needle bearingSP70_22Working pistonThe disc springOil pressure sideProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilityThe disc spring is located the oil pressure with respecton to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� side of the working piston.Disc springTask The disc spring pushes the working piston in the axial direction and generates a preload, whereby the disc pack and the needle bearings no longer exhibit a play.SP70_23SP70_24GB13The Haldex coupling in detailThe electro-hydraulic assembly groupThe electro-hydraulic assembly group consists of the pump for Haldex coupling V181, the oil filter, the accumulator and the valve for controlling the opening degree of the coupling N373. The pump for Haldex coupling V181 On the Haldex Generation IV coupling, the oil pressure is built up by an electrical reciprocating piston pump which is installed in the lower area of the clutch. The pump fills the accumulator in the oil circuit and is actuated by the control unit for Haldex couping J492 depending upon use. Function The cylinder housing of the pump has 5 holes. One piston with a guide pin and a return spring is located in each hole. When turning the cylinder housing, the piston and the guide pin are put into thrust motion by the ball bearing positioned at an angle. Thus, oil is sucked in through the lower hole in the cylinder housing. When the hole is turned by 180°, this oil is delivered to the top as compressed oil. Effects of failure If the pump for Haldex coupling fails, there is no oil pressure build-up. No more torque is transferred to the rear axle.SP70_25Oil is sucked in.Oil is delivered as compressed oilCylinder housing Ball bearingto accumulatorPiston Guide pin Return spring from oil reservoirSP70_26The oil filter The oil filter is a maintenance-free fleece filter. A non-return valve is integrated in the oil filter housing, which prevents the oil pressure from being released to the pump for Haldex coupling V181.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�14GBThe accumulator The accumulator is very compact and is arranged at the top of the clutch. It is composed of three parallel-acting springs. Their spring force sets the working oil pressure and maintains it at a level of 30 bar.System depressurised: The springs of the accumulator are slackened.from the pump of the clutch to valve N373SP70_27Return flow to oil reservoirSystem with operating pressure: The pressure chamber of the accumulator is filled by the pump for Haldex coupling. Thus, the pressure piston is pushed back and the springs are prestressed.Pressure pistonSP70_28Return-flow channelsPressure chamberIf the oil pressure is too high, above 30°bar, the return-flow channels are opened and as a esult the oil flows into the oil reservoir. In this way the oil pressure is reduced.to oil reservoirProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP70_29GB15The Haldex coupling in detailThe valve for controlling the opening degree of the coupling N373 The valve for controlling the opening degree of the coupling N373 controls the working pressure which is transferred to the working piston. The pressure value depends on the supply current. To each value of the supply current is assigned a precisely defined pressure, which is generated by the valve.Spring Needle to working piston Control chamber to accumulator Control piston to oil reservoirSolenoid coilFunctionSolenoid core PlugProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted An oil pressure of 30° bar is built up unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability SP70_30 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� by the pump for Haldex coupling V181 and the accumulator. (1)A solenoid force, whose strength depends on the adjacent current, is created by energising the solenoid coil. The solenoid force which is created in this way, moves the control piston and this opens the passage through which the oil flows to the working piston. (2) Once the desired working pressure is reached, the balance of forces (state of equilibrium) described below is achieved, so that the passage is closed and the working pressure can be constantly maintained. (3) The working pressure from the control chamber acts on the control piston. The pressure in the control chamber acts in the same direction as the reset force of the spring and supports the spring as a counterforce to the solenoid force. A balance of forces is achieved. When fully energising the solenoid coil, the inflow remains open and the complete oil pressure is used as working pressure.16123The working pressure is built up Oil pressure of 30 barOil passage closed; The working pressure is maintainedSP70_31Spring force+Pressure force Control chamber=Solenoid forceSP70_32GBIf the clutch is opened, the solenoid coil is no longer energised, the control piston returns to the initial position and the working pressure is released in direction of the oil reservoir. Effects of failure If the valve for controlling the opening degree of the coupling N373 fails, the drive torque can no longer be transferred to the rear axle. The all-wheel drive system does no longer function.Reduction of working pressure; Oil flows to oil reservoirSP70_33The control unit for Haldex coupling J492The control unit for Haldex couping regulates the running time of the pump and the valve for controlling the opening degree of the coupling N373. The high level of the pressure is exclusively determined by the position of the valve N373. A temperature sensor is located on the board of the control unit, whose measured values indicate the oil temperature. The control unit for Haldex coupling J492 is integrated in the CAN data bus drive. Through this, it can precisely regulate the complete all-wheel drive system with only one integrated Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability temperature sensor. control unit uses the data for A. the with respect to the correctness The of information in this document. Copyright by Š KODA AUTO S.� driving situation in order to determine the currently desired working pressure so that the opening degree of the coupling and the transfer of the drive torque to the rear axle is optimally attuned to the situation. If an ESP or ABS intervention occurs, the ABS control unit J104 determines the opening degree of the clutch via the control unit for Haldex coupling J492. Effects of failure If the control unit for Haldex coupling fails, the clutch is opened and the drive torque can no longer be transferred to the rear axle.SP70_34GB17Control of the Haldex couplingThe oil circuitThe electro-hydraulic components of the system build up the oil pressure and control the contact pressure on the multiple disc clutch.Working piston Disc spring Valve for controlling the opening degree of the coupling N373Pressure lineOil returnMultiple disc clutchOil filterProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� AccumulatorControl unit for Haldex coupling J492Strainer Oil reservoirSP70_35Pump for Haldex coupling V181System depressurised As long as the engine is switched off and only the ignition is switched on, the control unit for Haldex coupling J492 is actuated but no pressure build-up occurs. As long at the valve for controlling the opening degree of the coupling N373 is de-energized, the oil inflow to the working piston is shut off (pressure line), the return flow to the oil reservoir is opened.A depressurised system is required for the following situations: Dynamometer TowingSP70_36SP70_37As a low basic torque is already applied by the disc spring, a speed of 50°km/h and a distance of 50°km must not be exceeded while towing with a raised front axle.18GBPressure build-up when engine is started If the engine is started, the pump for Haldex coupling V181 is activated. As soon as an engine speed of 400 rpm is reached, the pump is actuated. It delivers oil to the accumulator via the oil filter until a pressure of 30°bar is reached in the oil circuit. The valve for controlling the opening degree of the coupling N373 is actuated by the control unit for Haldex coupling J492, the pressure line opens, the working pressure is transferred to the working piston and the disc pack is compressed.Working piston Disc spring Pressure line (0-30 bar) Valve for controlling the opening degree of the coupling N373 Oil pressure of 30 bar Oil returnMultiple disc clutchProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Oil filterControl unit for Haldex coupling J492Accumulator Strainer Oil reservoirSP70_38Pump for Haldex coupling V181Starting up When starting up and accelerating, the complete rear wheel drive torque is immediately available.System when driving In each driving situation, the pressure in the system between the pump for Haldex coupling and the valve for controlling the opening degree of the coupling N373 is maintained at a constant pressure of 30°bar by the accumulator. The control of the working pressure takes place solely via the valve N373. The working pressure can be between 0% (e.g. when braking) and 100% (e.g. when accelerating).SP70_39GB19Control of the Haldex couplingDriving situationsStarting up or accelerating When starting up and accelerating, a high drive torque is needed on the rear axle. The valve for controlling the opening degree of the coupling N373 opens the pressure line completely and the working pressure can reach up to maximum level. Fast driving Only a low torque is needed on the rear axle. The contact pressure must be controlled based on need (control range).100% Drive torque of rear axle 100%0%Control range Starting up/acceleratingSP70_40 SP70_41Control range 0%Fast drivingSP70_42SP70_43Brakes No more torque must be transferred to the rear axle when braking. The valve for controlling the opening degree of the coupling closes the pressure line completely and opens the return flow line. The working pressure is reduced and the Haldex coupling is opened. Stopping100%0%BrakesSP70_44SP70_45As long as the vehicle is braked, the clutch is 100% opened. When the vehicle is stationary, the pilot control of the control unit for Haldex coupling Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability uses the signal of the accelerator pedal unless posiwith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� tion. When starting up, the working pressure 0% SP70_47 is again built up and the full drive torque is Stopping SP70_46 available at the rear axle. Parking When parking, only a low drive torque is transferred to the rear axle. The Haldex coupling is regulated based on need (control range).100%Control range 0%ParkingSP70_48SP70_4920GBCritical driving situations Driving on slippery road The working pressure is controlled based on need. Signals from the ABS control unit J104, which recognises slip by means of the speed sensors and calculates the required traction, are used in order to control the working pressure.Drive torque of rear axle 100%SP70_50ESP or ABS intervention When activating a wheel slip control system, the opening degree of the clutch is indirectly controlled by the ABS control unit J104. Thus, the clutch can be opened completely for example for an ABS intervention, whereby it can be closed for an ESP intervention.Control range0% Driving on slippery road or ESP or ABS interventionSP70_51Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Starting up with slip If both wheels of the front axle are spinning, the Haldex coupling is closed and the highest possible drive torque is transferred to the rear axle.SP70_52SP70_53If only one wheel of the front axle is spinning, the electronic differential lock (EDL) intervenes by braking the spinning wheel and thus the driving force of the other wheel is increased. At the same time the Haldex coupling is closed and a large portion of the driving force is tranferred to the rear axle.SP70_54GB21System overviewSystem overviewSensors ActuatorsEngine speed sender G28Engine control unit J623 Accelerator pedal position sender G79Valve for controlling the opening degree of the coupling N373Speed sensors G44-G47Control unit for Haldex coupling J492 ABS control unit J104Brake light switch FCAN data bus drivePump for Haldex coupling V181Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Data bus diagnostic interface J533Steering angle sender G85SP70_5522GBFunction diagramFunction diagramTml. 30 J104J623SG85J492V181Tml. 31SP70_56G85 J104 J492 J623 Steering angle senderABS control unit unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Control unit for Haldex with coupling Engine control unitPlus Earth CAN databus cable Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedN373 Valve for controlling the opening degree of the coupling S V181 Fuse Pump for Haldex couplingGB23ServiceDiagnosisDiagnosis functions The following diagnosis functions are available with the diagnostic testers VAS 505x: - identification of the control units - interrogate fault memory - erase fault memory - read measured value blocks - actuator test - basic setting - adaptation - coding The individual diagnosis functions are accessible via the targeted fault finding or the targeted functions.Function test of the Haldex couplingIn order to avoid the risk of accidents during the test and measurement drives/test and measurement work, proceed as follows: For reading the measured value blocks, only the vehicle diagnosis, measuring and information system -VAS 505x- can be used. The vehicle diagnosis, measuring and information system -VAS 505x- is connected to the diagnostic socket when the ignition is switched off. Before the repair of the Haldex coupling, determine the fault cause as precisely as possible in the operating conditions with the vehicle diagnosis, measuring and information system -VAS 505x-: Protected Finding by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted - targeted unless Fault authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� - vehicle self diagnosis - measuring technique Prerequisite for the function test of the Haldex coupling: - oil level in the Haldex coupling O.K. - the correct engine control unit and the ABS/ESP control unit is fitted (check the coding and the identification of the control units) - lift the vehicle with the jack so that the wheels do no touch the ground24GBFunction test of the Haldex coupling for vehicles with manual gearbox Procedure: - operate clutch pedal - start up engine - engage 1st gear - slowly release the clutch pedal Now, all 4 wheels must turn. - apply handbrake The rear wheels must stop, the front wheels continue to turn. - release handbrake - always engage 1st gear - operate accelerator pedal by approx. 20-30% - slowly apply handbrake The rear wheels continue to turn. If the test was successful, the Haldex coupling functions correctly. If the test was not successful, the Haldex coupling functions incorrectly. Possible causes: - the valve for controlling the opening degree of the coupling N373 can be blocked - mechanical fault of the Haldex coupling - control unit for Haldex coupling J492 defective - switch for hand brake indicator F9 defectiveGBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�25ServiceFunction test of the Haldex coupling for vehicles with automatic gearbox Procedure: - operate brake pedal - start up engine - select driving mode "D" - release brake pedal Now, all 4 wheels must turn. - apply handbrake The rear wheels must stop, the front wheels continue to turn. - release handbrake - always select driving mode "D" - operate accelerator pedal by approx. 20-30% - slowly apply handbrake The rear wheels continue to turn. If the test was successful, the Haldex coupling functions correctly. If the test was not successful, the Haldex coupling functions incorrectly. Possible causes: - the valve for controlling the opening degree of the coupling N373 can be blocked - mechanical fault of the Haldex coupling - control unit for Haldex coupling J492 defective - switch for hand brake indicator F9 defectiveService informationProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�- The Haldex Generation IV coupling is individually replaceable. Extensive setting operations after the exchange are not needed, because the drive pinion is part of the rear axle drive and does not have to be replaced. - The heavy-duty oil was especially developped for the requirements of the Haldex Generation IV coupling.26GBNotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB27List of Self-Study Programmes so far No. Title No. Title 1 Mono-Motronic 2 Central locking 3 Anti-Theft Alarm 4 Working with current flow diagrams 5 ŠKODA FELICIA 6 ŠKODA-Vehicle safety 7 Principles of ABS - not published 8 ABS-FELICIA 9 Immobilizer with transponder 10 Air conditioning in vehicles 11 Air conditioning FELICIA 12 1.6-ltr. engine with MPI 13 1.9-ltr. Naturally aspirated diesel engine 14 Power-assisted steering 15 ŠKODA OCTAVIA 16 1.9-ltr. TDI engine 17 OCTAVIA Convenience electronic system 18 OCTAVIA Manual gearbox 02K/02J 19 1.6 ltr./1.8 ltr. petrol engines 20 Automatic gearbox - fundamentals 21 Automatic gearbox 01M 22 1.9 ltr./50 kW SDI, 1.9 ltr./81 kW TDI 23 1.8 ltr. 110 kW turbo petrol engine 1.8 ltr. 92 kW petrol engine 24 OCTAVIA, CAN databus 25 OCTAVIA - CLIMATRONIC 26 OCTAVIA - Vehicle safety 27 OCTAVIA - 1.4-ltr. Engine and Gearbox 002 28 OCTAVIA - ESP 29 OCTAVIA - 4x4 30 2.0 ltr. 85 kW/88 kW petrol engine 31 OCTAVIA - Radio/navigation system 32 ŠKODA FABIA 33 ŠKODA FABIA - Vehicle electrics 34 ŠKODA FABIA - Power-assisted steering 35 1.4 ltr. - 16V 55/74 kW petrol engines 36 ŠKODA FABIA - 1.9 ltr. TDI Unit injection 37 5-Speed manual gearbox 02T and 002 38 ŠkodaOctavia - Model 2001 39 Euro-On-Board-Diagnosis 40 Automatic gearbox 001 41 6-Speed manual gearbox 02M 42 ŠkodaFabia - ESP 43 Exhaust emission 44 Extended maintenance interval 45 1.2 ltr. 3-cylinder petrol engines 46 ŠkodaSuperb; Presentation of the vehicle part I 47 ŠkodaSuperb; Presentation of the vehicle part II 48 ŠkodaSuperb; 2.8-ltr./142 kW V6 petrol engine 49 ŠkodaSuperb; 2.5-ltr./114 kW TDI V6 Diesel engine 50 ŠkodaSuperb; Automatic gearbox 01V 51 2.0 ltr./85 kW Petrol Engine with balance shaft transmission and 2-stage switching intake manifold 52 ŠkodaFabia; 1.4-ltr. TDI engine with unit injection system 53 ŠkodaOctavia; Presentation of the vehicle 54 ŠkodaOctavia; Electrical Components 55 FSI Petrol Engines; 2.0 ltr./110 kW and 1.6 ltr./85 kW 56 Direct manual gearbox 57 Diesel engine 2.0 ltr./103 kW TDI Unit injector 2.0 ltr./100 kW TDI Unit injector 58 ŠkodaOctavia; Chassis and electromechanical power-assisted steering 59 ŠkodaOctavia RS, 2.0 ltr./147 kW FSI turbo petrol engine 60 2.0 ltr./103 kW 2V TDI diesel engine; diesel particle filter system with additive 61 Satellite navigation systems in Škoda vehicles 62 ŠkodaRoomster; Presentation of the vehicle part I 63 ŠkodaRoomster; Presentation of the vehicle part II 64 ŠkodaFabia II; Presentation of the vehicle 65 ŠkodaSuperb ll; Presentation of the vehicle part I 66 ŠkodaSuperb ll; Presentation of the vehicle part II 67 2.0 ltr./125 kW TDI diesel engine with Common Rail injection system 68 1.4 ltr./92 kW TSI petrol engine with turbocharging 69 3.6 ltr./191 kW FSI petrol engine 70 All-wheel drive with Haldex coupling Generation IVOnly intended for internal use in the Škoda-Organisation. All rights reserved. Subject to technical modification. This paper was made out of Protected by copyright. Copying for 01/2009 private or commercial purposes, in part or in whole, chlorine-free is not permitted S00.2002.70.20 E GB Technical status bleached cellulose. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� © ŠKODA AUTO a.s. http://portal.skoda-auto.com70