TECHNICAL DOCUMENTATION
SSP 075 7-speed automatic gearbox 0AM

This PDF is currently unavailable.
Read document text
Service7-speed automatic gearbox 0AMwith dual-clutch75Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Service TrainingThe continuing development of the highly successful direct shift gearbox 02E led to the creation of the 7-speed dual-clutch gearbox 0AM. Just as the direct shift gearbox 02E, it fulfills the increased demand for driving comfort while ensuring that a gear change with no interruption of power flow can be implemented. It is designed for engines with a torque of up to 250 Nm.While the direct shift gearbox in terms of fuel consumption is still at a level comparable to vehicles fitted with manual gearboxes, identical technical innovations in the transmission design of the dualclutch gearbox 0AM contribute to a reduced fuel consumption compared to vehicles fitted with manual shift gearboxes. A reduced fuel consumption contributes significantly toward reduction in emissions.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�2GBContentsBrief description of the gearbox 4Selector lever Construction of the gearbox Mechatronics module Electronic control unit Electro-hydraulic control unit Hydraulic oil circuit Transmission control system Notes6 7 27 28 29 30 44 58Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�You will find the notes for the assembly and disassembly, repair, diagnostics as well as detailed user information in the diagnostics, measuring and information system VAS 505x. The time for going to press was on the 12/2009. This brochure is not subject to an update.GB3Brief description of the gearboxGearbox characteristicsThe dual-clutch gearbox 0AM represents two premieres for the company Škoda: • the first 7-speed gearbox with engine mounting system for a vehicle with a transversely mounted engine • the first gearbox with a dry dual-clutch.mechatronicsdual-clutchSP75_01The characteristic design feature of the dry dual-clutch has important consequences for the overall concept of the gearbox. The degree of ef ficiency of this gearbox, compared to the direct shift gearbox 02E, is increased by its new design concept. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The improved ef ficiency contributed significantly to the reduction of fuel consumption and emissions. The 7-speed dual-clutch gearbox 0AM represents a milestone in gearbox strategy and enables the company to achieve its objectives through further technological advances.4GBDesign features• modular design of the gearbox: clutch, mechatronics and gearbox form one unit • dry dual-clutch • separate oil circuit: mechatronics and manual gearbox with life time fillings of the gearbox • 7 stages with four shafts • oil pump actuated based on current need • no oil or water heat exchangermechatronicsdual-clutchSP75_02Technical dataDesignation Weight torque Gear stages Gradation of the gear stages Operating mode Oil volume in the gearbox Oil volume in the mechatronics 0AM approx. 70 kg including clutch 250 Nm 7 forward gear stages, 1 reverse gear 8,1 automatic mode and Tiptronic mode approx. 1.7 ltr. - G 052 171 approx. 1 ltr. - G 004 000Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB5Selector leverOperationThe selector lever is actuated in the same way as on a vehicle with automatic gearbox. The dualclutch gearbox also offers the option of Tiptronic gear selection. As on vehicles with automatic gearboxes, the selector lever features a selector lever lock as well as an ignition key lock for ignition key removal. The locking function is the same as before. The design is new.release buttonThe selector lever positions are: P - Park To move the selector lever out of this position, the ignition must be "switched on" and the brake pedal applied. Furthermore, the release button on the selector lever must be pressed. R - Reverse gear To engage this gear, the release button must be pressed. N - Neutral In this position, the gearbox is at idle. If the selector lever is left in this position for a lengthy period of time, the brake pedal must be pressed again for it to be disengaged from this position.SP75_03Tiptronic switch on the steering wheel E389D - Permanent forward drive position (normal program) In this drive position (Drive) the forward Protected gear by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability stages are selected automatically.unless with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� S - Sport The individual gears stages are selected automatically after using a program with "sporty" driving characteristics stored in the control unit. +/– The Tiptronic functions can be controlled with the selector lever located in the right gate and from the switches on the steering wheel.SP75_046GBConstruction of the gearboxBasic principleThe automatic dual-clutch gearbox 0AM comprises essentially two part transmissions which are independent of each other. In functional terms, each part transmission is constructed in the same way as a manual gearbox and one clutch is allocated to each part transmission. Both clutches are of the dry type. They are opened and closed by the mechatronics system, depending on the selected gear stage. The 1st, 3rd, 5th and 7th gear stages, which are mounted in the part transmission (K1), are selected via the clutch K1 and the input shaft 1. The 2nd, 4th, 6th and the reverse gear (R) are components of the part transmission 2 (K2) and are shifted via the clutch K2 and the input shaft 2. The torque is always transferred to the wheels by one part transmission. The second part transmission has the next gear pre-selected in preparation, however the clutch for this gear stage or gearbox is still held in the non-engaged position. Every gear stage is allocated a conventional manual gearbox synchronisation and selector unit.part transmission 2Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�642R input shaft 2 K2K1 7 5 3 1torqueinput shaft 1SP75_13part transmission 1GB7Construction of the gearboxTorque inputThe torque is transferred from the dual mass flywheel (attached to the crankshaft) to the dual-clutch. The dual mass flywheel is provided with inner toothing for meshed coupling with the outer toothing on the support ring of the dual-clutch. The torque is then transferred from here to the dual-clutch.input shaft 1 and 2 support ring outer toothinginner toothingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_14dual-clutchdual mass flywheel8GBDual-clutch and course of the torqueThe dual-clutch is disposed in the bell housing of the gearbox. It comprises two conventional clutches that are part of the dual-clutch body. In the service training manuals, the clutches are further referred to as K1 and K2. The clutch K1 transfers the torque to the input shaft 1 via the longitudinal grooved spline. From the input shaft 1, the torque for the 1st and 3rd gear stages is then transferred to the driven shaft 1 and the torque for the 5th and 7th gear stages is transferred to the driven shaft 2. The clutch K2 transfers the torque to the input shaft 2 via the longitudinal grooved spline. From the input shaft 2, the torque for the 2nd and 4th gear stages is then transferred to the driven shaft 1 and the torque for the 6th and reverse gear (R) is transferred to the driven shaft 2. The torque is then transferred via the engaged gear wheel of the reverse gear R1 to the gear wheel of the reverse gear R2 and to the driven shaft 3. All three driven shafts are connected to the toothed gear of the transfer gearbox for the differential gear.driven shaft 3 clutch K2 dual mass flywheelProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�clutch K1driven shaft 2input shaft 1input shaft 2driven shaft 1SP75_15toothed gear of the transfer gearboxdifferential gearGB9Construction of the gearboxDrive pulley of the dual-clutchThe torque is transferred from the support ring to the drive pulley in the dual-clutch. The support ring and the drive pulley are mutually firmly connected. The drive pulley is freely mounted on the input shaft 2.Function If one of the two clutches (K1; K2) is engaged, the torque is transferred from the drive pulley to the relevant plate of the clutch and then to the respective input shaft.support ringProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted drive pulley unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_16input shaft 1 and 2dual mass flywheel clutch K2clutch K1SP75_1710GBClutchesTwo independent dry clutches (K1; K2) operate in the dual-clutch, which transfer the torque to one part transmission at a time. Clutch positions: • when the engine is at idle and in freewheel mode, both clutches are disengaged. • only one of the two clutches is engaged while driving. clutch K1 The clutch K1 transfers the torque via the input shaft 1 for the 1st, 3rd, 5th and 7th gear stages.Clutch K1 in a non-engaged positioninput shaft 1Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_18GB11Construction of the gearboxFunction After engaging the clutch, the axial bearing is pressed on the disc spring by the control lever. At several turning points the pressing movement is converted into a pulling movement. In this way, the press-on disc is pulled towards the clutch plate and the drive pulley so that the torque is transferred to the input shaft. The control lever is operated by the valve 3 of the part transmission 1 N435 via the hydraulic control element of the clutch K1.Clutch K1 in an engaged positionpress-on disc hold pointaxial bearingSP75_20disc springdrive pulley disc spring clutch plateProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�control leverSP75_1912GBClutch K2 The clutch K2 transfers the torque via the input shaft 2 for the 2nd, 4th, 6th gear stages and the reverse gear (R).Clutch K2 in a non-engaged positioninput shaft 2Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_21GB13Construction of the gearboxFunction If the control lever is pressed, the axial bearing presses against the disc spring of the press-on disc. The disc spring is supported by the clutch housing, in such a way that the press-on disc is pressed against the drive pulley and in turn the torque is transferred to the input shaft 2. The control lever is operated by the valve 3 of the part transmission 2 N439 via the hydraulic control element of the clutch K2.Clutch K2 in an engaged positiondrive pulleypress-on disc hold point disc springProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�clutch plate axial bearingcontrol leverSP75_2214GBInput shaftsThe input shafts are mounted in the gearbox housing. They transfer the torque of the engine to the driven shafts depending on the selected gear stage. Each input shaft is joined to the clutch by a longitudinal grooved spline. The input shaft 2 has longitudinally drilled bores. The input shaft 1 is guided through the bore opening. The gearbox housing accomodates each input shaft which is mounted with a ball bearing.Mounting position in the gearbox (left view - stretched view)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_23input shaft 2 input shaft 1SP75_24longitudinal groovedball bearingGB15Construction of the gearboxThe input shaft 2 is described by the mounting position in front of the input shaft 1. Input shaft 2 The input shaft 2 is a hollow construction and is joined via the longitudinal grooved spline to the clutch K2. The 2nd, 4th, 6th and R gear stages are shifted via the input shaft 2. To measure the input speed (speed of the input shaft 2) there is a toothed pulse wheel for the input speed sender 2 G612 located on the shaft.toothed pulse wheel bearingSP75_254th and 6th gear stages2nd gear stage and RInput shaft 1 The input shaft 1 is joined to the clutch K1 by the longitudinal grooved spline and the 1st, 3rd and 7th gear stages are selected via this clutch. To measure the gearbox input speed (speed of the input shaft 1) there is a pulse wheel for the gearbox input speed sender 1 G632 located on the input shaft.bearingpulse wheel7th gear stageProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_261st gear stage 5th gear stage3rd gear stageYou will find additional information regarding the pulse wheel in the Service Training No. 56.16GBDriven shaftsThree driven shafts are mounted in the gearbox housing. Depending on the selected gear stage, the engine torque is further transferred from the input shafts to the driven shafts. Each driven shaft is fitted with a driven toothed gear which ensures the transfer of torque to the toothed gear of the transfer gearbox for the differential gear. Driven shaft 1 Located on the driven shaft 1 are: • the three-fold synchronised selector gears for 1st, 2nd, and 3rd gear stages • the two-fold synchronised selector gear for the 4th gear stageMounting position in the gearbox (left view - stretched view)SP75_271st gear stage3rd gear stage4th gear stage2nd gear stageProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�driven toothed gearbearingbearingSP75_28sliding sleeve of 1st and 3rd gear stagessliding sleeve of 2nd and 4th gear stagesGB17Construction of the gearboxDriven shaft 2 Located on the driven shaft 2 are: • the single synchronised selector gears for the 5th, 6th, and 7th gear stages • engaged gear wheels of the R1 gear stage and the R2 gear stage of the reverse gearMounting position in the gearbox (left view - stretched view)SP75_295th gear stage7th gear stage6th gear stageR1: reverse gearR2: reverse gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_30sliding sleeve of 5th and 7th gear stagesSliding sleeve of the gear stage 6th and Rdriven toothed gear18GBDriven shaft 3 Located on the driven shaft 3 are: • the single synchronised selector gear for R gear stage • parking lock gear wheelMounting position in the gearbox (left view - stretched view)SP75_31parking lock gear wheelgear wheel of gear stage R driven toothed gearbearingbearingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_32sliding clutch sleeveGB19Construction of the gearboxDifferential gear The differential gear transfers the torque to the propshafts and in turn they distribute the torque to the road wheels of the vehicle.Mounting position in the gearbox (left view - stretched view)SP75_33toothed gear of the transfer gearboxProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_3420GBParking lockThe parking lock with dual-clutch integrated in the gearbox secures the vehicle in order to prevent it from moving when stopping, in the event that the handbrake is not applied. The engagement of the parking lock is purely mechanical via a Bowden cable located between the selector lever and the parking lock lever on the gearbox. The Bowden cable is used exclusively to actuate the parking notch.bolt for the connection of the Bowden cable of the parking lock parking lock leverlocking pawlretaining spring of the locking pawlbracket locking springoperating boltpreloaded springProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_35parking lock gear wheelGB21Construction of the gearboxFunction The parking lock is not engaged. (selector lever position R, N, D, S)bracketWhen the parking lock is not engaged, the cone of the operating bolt rests against the bracket and the locking pawl. In this way, the locking pawl is held in the unlocked position by the spring.locking springoperating bolt locking pawlSP75_36Parking lock engaged (selector lever position R) - The detent lug is not engaged: The cone of the operating bolt is pressed against the bracket and the locking pawl by engaging the parking lock. The locking pawl moves down due to the fixed position of the bracket. If the lug of the locking pawl strikes against one of the teeth of the parking lock gear, the preloaded spring is pressed onto the operating bolt. The operating bolt is held in this position by the locking pin.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�locking pinpreloaded spring is pressed togetherSP75_37- The detent lug is engaged: If the vehicle continues to move, the parking lock gear wheel turns at the same time. The operating bolt is pressed by the force of the spring which in turn allows the locking pawl to be automatically pushed into the next tooth gap on the parking lock gear.operating bolt in the final positionpreloaded spring is released lug of locking pawl, engaged in the parking lock gear wheelSP75_3822GBSynchronisation of the gear stagesAn ensured synchronisation with locking bodies is needed to synchronise different torques when shifting between gears. The gear stages are synchronised one to three times depending on the load of the individual gear stage when shifting gears.The figure shows the synchronisation of the 2nd, 4th and R gear stages.toothed gear 2 of the gear stage outer ring (intermediate ring) locking body selector forkintermediate ring toothing of the clutchsynchronisation ring (inner) synchronisation ring (outer) core of the synchronisation clutch clutch sleeve synchronisationProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted ring AUTO (outer) unless authorised by ŠKODA AUTO A. S. ŠKODA A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� synchronisationSP75_69ring (inner) toothed gear 4 of the gear stagegear wheel of the reverse synchronisation ringlocking bodycore of the synchronisation clutchSP75_70clutch sleeveGB23Construction of the gearboxTransmission routes through the gearsThe transfer of torque in the gearbox takes place either via the clutch K1 or the clutch K2. Each clutch drives an input shaft. The input shaft 1 is driven by the clutch K1 and the input shaft 2 by the clutch K2.The power is transmitted to the differential gear • via the driven shaft 1 for the 1st, 2nd, 3rd and 4th gear stages • via the driven shaft 2 for the 5th, 6th and 7th gear stages as well as • via the driven shaft 3 for the reverse gear and the parking lockSP75_39SP75_401st gear stage clutch K1 input shaft 1 driven shaft 1 differential gearReverse gear clutch K2 input shaft 2 driven shaft 3 differential gearThe change in direction of rotation for the reverse gear is carried out via the driven shaft 3.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�For a clearer presentation, the route of the transmission is schematically illustrated in a "stretched graphic".24GB2nd gear stage clutch K2 input shaft 2 driven shaft 1 differential gearSP75_413rd gear stage clutch K1 input shaft 1 driven shaft 1 differential gearSP75_424th gear stage clutch K2 input shaft 2 driven shaft 1 differential gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability SP75_43 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB25Construction of the gearbox5th gear stage clutch K1 input shaft 1 driven shaft 2 differential gearSP75_44Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�6th gear stage clutch K2 input shaft 2 driven shaft 2 differential gearSP75_457th gear stage clutch K1 input shaft 1 driven shaft 2 differential gearSP75_4626GBMechatronics modulemechatronics of the dual-clutch gearbox J743The mechatronics form the central control unit in the gearbox. The mechatronics module comprises the electronic control unit as well as the electro-hydraulic control unit. The mechatronics are connected to the gearbox with a flange and form an independent unit. The mechatronic module is supplied by its own oil circuit, which is separate from the oil circuit of the manual gearbox. The advantages of the independent mechatronic module are: • apart from one sensor, all the sensors and control elements are integrated in the mechatronics. • The hydraulic fluid was developed specifically for the needs of the mechatronics. • Because of its own oil circuit, the penetration of wear particles from the mechanical part of the gearbox into the mechatronic module is avoided. • Favourable behaviour at low temperatures.mechatronicsSP75_47Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB27Electronic control unitElectronic control unitThe electronic control unit of the mechatronics forms the central control unit in the gearbox. All the sensor signals or sender signals and the signals from all the other control units are combined in the electronic control unit which activates and monitors at the same time all the control elements. Housed in the electronic control unit are 11 sensors (senders), only the gearbox input speed sender G182 is located outside the control unit. The electronic control unit controls eight electromagnetic valves required for shifting through the seven gear stages and for the operation of the clutches. The electronic control unit adapts the positions of the clutches as well as the positions of the control elements of the gear stages when a gear is engaged and initiates the relevant adaptation of the modules involved.clutch temperature sensor G510 travel sensor 3 for gear actuator of gear stage G489 (5th and 7th gear stages) travel sensor 4 for gear actuator of gear stage G490 (6th and R gear stages) Gearbox input speed sender 2 G612 electrical connection travel sensor 1 for gear actuator of gear stage G487 (4th and 2nd gear stages) gearbox input speed sender G182Gearbox input speed sender 1 G632electronic control unit with integrated sensorstravel sensor 2 for gear actuator of gear stage G488 (1st and 3rd gear stages)SP75_48Travel sensor of clutch 1 G617 Travel sensor of clutch 2 G618gearbox hydraulic pressure sensor G270Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_4928GBElectro-hydraulic control unitElectro-hydraulic control unitThe electro-hydraulic control unit is integrated in the module of the mechatronics. It provides the oil pressure which is required for shifting through the gear stages and for the operation of the clutches. Generation and control of oil pressure The oil pressure is generated by a hydraulic pump that is driven by an electric motor. The oil pressure vessel ensures there is always suf ficient oil pressure supplied to the electromagnetic valves.electro-hydraulic control unitpressure oil tankto clutch K1 hydraulic pump to clutch K2 valve 2 of part transmission 2 N438 for gear actuator of 6th and R gear stages valve 4 of part transmission 2 N440 of the oil pressure control valve 3 of part transmission 2 N439 of the clutch K1 valve 1 of part transmission 2 N437 for gear actuator of 2nd and 4th gear stagesSP75_50valve 3 of part transmission 1 N435 of the clutch K1 and valve 2 of part transmission 1 N434 for gear actuator of 5th and 7th gear stages valve 4 of part transmission 1 N436 of the oil pressure control valve 1 of part transmission 1 N433 for gear actuator of 1st and 3rd gear stages hydraulic pump motor V401Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability withGB respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�29Hydraulic oil circuitOil circuitThe dual-clutch gearbox operates with two oil circuits independent of each other which are filled with two different types of oil: • oil circuit of the manual gearbox • oil circuit of the mechatronic module Each oil circuit contains oil that is responsive and specially adapted to the needs of the individual circuit.oil circuit of the manual gearbox oil circuit of the mechatronicsSP75_51Oil circuit of the manual gearbox The filling and lubrication of the gearbox including the corresponding shafts and gear wheels are performed in the same way as on a normal manual gearbox.Oil circuit of the mechatronic module Filling the mechatronic module is performed independantly from the oil circuit of the manual gearbox. The oil pump delivers the pressure oil which ensures the functioning of the hydraulic components of the mechatronics. The volume of the oil in the mechatronics is 1.1 ltr.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The volume of oil in the manual gearbox is 1.7 ltr.The exact amount of oil filling required is stated in the ELSA service workshop manual electronic information system of the company.30GBOil circuit diagramPrimary oil circuithydraulic pump motor V401filterpressure regulator valve pressure oil tank hydraulic oil pressure sensorhydraulic pumpnon-return valveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_52GB31Hydraulic oil circuithydraulic pumpThe hydraulic pump unit is located in the mechatronic module. It consists of the hydraulic pump and the electric motor. The hydraulic pump motor is a brushless DC motor. Depending on the required pressure, it is activated by the electronic control unit of the mechatronics. The hydraulic pump is driven via a shifting clutch.hydraulic pumpSP75_50hydraulic pump motor V401suction sideThe hydraulic pump operates on the principle of a gear wheel pump. It draws in the hydraulic oil, condenses the oil to the value of approx. 7 MPa and forces the oil to flow further into the oil circuit Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted of the mechatronics. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The hydraulic oil is transported from the suction side to the pressure side as it flows between the walls of the pump housing and the tooth gaps.housingSP75_53delivery sidedrive wheel32GBHydraulic pressure sensor G270 and pressure regulator valveThe hydraulic pump pushes the hydraulic oil through a filter in the direction of the pressure regulator valve, the pressure vessel and the oil pressure sensor. If the pressure of the hydraulic oil at the pressure regulator valve and at the oil pressure sensor reaches a value of approx. 6 to 7 MPa, the control unit switches off the electric motor and thus the hydraulic pump. The bypass ensures the functioning of the system in case the filter channel is clogged.pressure regulator valveSP75_54hydraulic oil pressure sensorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Pressure vesselThe pressure vessel is designed as a gas pressure vessel. It supplies the hydraulic system with pressure oil provided the hydraulic pump is switched off. The volume of the vessel is 0.2 litres.pressure oil tankSP75_55GB33Hydraulic oil circuitOil circuit diagramworking pressure return flow regulated working pressure KS safety valves of the clutchSP75_56KSKSgear actuator of 1st and 3rd gear stagescontrol element of the clutch K1 gear actuator of gear actuator of 5th and 7th gear 4th and 2nd gear stages stagescontrol element of the clutch K2 gear actuator of 6th and R gear stagesThe safety valves of the clutches allow the discharge of oil and herewith the clutches are decoupled in the event of a deficiency.34Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted GB unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Electromagnetic valves for the oil circuitFunction Electromagnetic valves for oil pressure control of part transmission They control the oil pressure for the part transmission 1 and 2. If a deficiency is detected in the part transmission, the electromagnetic pressure control valve will disengage the relevant part transmission.valve N436 of part transmission 1SP75_57valve N440 of part transmission 2Electromagnetic valves for gear actuator of the gear stages They regulate the amount of oil supplied to the gear actuators of the gear stages. Each gear Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised ŠKODA AUTO A. S. ŠKODA AUTOthrough A. S. does not guarantee or accept any liability actuator ofby the gear stages shifts two with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� gear stages. If no gear stage is selected, the gear valve N434 actuators of the gear stages are kept in the neut- of 5th and 7th gear ral position by way of the oil pressure. When the stages selector lever is in position "P" and the ignition is switched off, the 1st gear stage and the reverse valve N433 gear stage are selected.of 1st and 3th gear stagesSP75_58valve N438 of 6th and R gear stagesvalve N437 of 2nd and 4th gear stagesElectromagnetic valves for the control elements of the clutch They regulate the quantity of oil supplied to the control elements of the clutches which is needed to operate the clutches K1 and K2. The electromagnetic valves are de-energized and the clutches are in the open position.valve N435 of the clutch K1valve N439 of the clutch K2SP75_59GB35Hydraulic oil circuitSchalten der GetriebestufenDie Getriebestufen werden wie bei den üblichen mechanischen Getrieben durch Schaltgabeln geschaltet. Jede Schaltgabel schaltet jeweils zwei Getriebestufen. The selector forks are on opposite sides of the gearbox housing. When selecting gears, the selector forks are moved by means of the gear actuators of the gear stages which are integrated in the mechatronic module.selector fork of 5th and 7th gear stages selector fork of 6th and R gear stages selector fork of 1st and 3rd gear stagesselector fork of 2nd and 4th gear stagesSP75_60Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�36GBGear actuator of the gear stages and the selector forkThe piston of the gear actuator for the gear stages is connected to the selector fork. In order to change through the gears, the piston of the gear actuator for the gear stages is shifted by the forces of the oil pressure exerted on it. When the piston is shifted, the selector fork and the clutch sleeve shift at the same time. The clutch sleeve moves via the core of the synchronisation clutch and in this way the gear stage is selected.gear actuator of gear stages (5th and 7th) gear actuator of gear stages (6th and R)SP75_61gear actuator of gear stages (1st and 3rd) travel sensor of gear actuator for gear stages cylinder of gear actuator for gear stagesgear actuator of gear stages (2nd and 4th)piston of gear actuator for gear stagesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�permanent magnetselector forkclutch sleevecore of the synchronisation clutchSP75_62The mechatronics detect the new position of the selector fork by means of the permanent magnet and the gear actuator of the gear stages.GB37Hydraulic oil circuitShifting procedureThe actuation of the selector forks is hydraulic, just as on a direct shift gearbox 02E. For a gear shift operation, the electronic selector unit initiates the actuation of the relevant electromagnetic valve for the gear actuator of the gear stages by means of the mechatronics.Function The example illustrates the selection of the 1st gear stage.Initial position The piston of the gear actuator is held in the "N" position by the force of the oil pressure resulting from valve 1 of part transmission N433 for the 1st and 3rd gear stages. No gear stage is selected. The valve 4 of part transmission1 N436 regulates the oil pressure in the part transmission 1.mechatronicsvalve N436 of part transmission 1 valve N433 of 1st and 3th gear stages cylinder of gear actuator for gear stagesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�piston of gear actuator for gear stagespiston chamber selector fork clutch sleeveSP75_6338GBSelection of the 1st gear stage To select the 1st gear stage, the valve for the gear actuator of the gear stages increases the oil pressure in the left piston chamber. This causes the piston for the gear actuator of the gear stages to be pressed to the right. As the selector fork and the clutch sleeve are connected to the piston for the gear actuator of the gear stages, they also move to the right. The 1st gear stage is engaged by moving the clutch sleeve.mechatronicsvalve N433 of 1st and 3th gear stagescylinder of gear actuator for gear stages piston of gear actuator for gear stagespiston chamberProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability selector fork with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�clutch sleeveSP75_64GB39Hydraulic oil circuitControl element of the clutchThe clutches K1 and K2 are hydraulically operated by means of the control elements of the clutch (one control element for each clutch) which are mounted in the mechatronic module. The control element of the clutch consists of the cylinder and the piston. The piston of the clutch control element actuates the control lever of the clutch. A permanent magnet is located at the piston of the clutch control element which determines the position of the piston in combination with the travel sensor of the clutch 1 G617. In order to determine the position of the piston, the cylinder and the piston of the control element must be non-magnetic.control element of the clutch K1 cylinder of the clutch control element permanent magnet sleeve piston of the clutch control element piston rodprotective sleeveretaining ringguide ringcontrol element of the clutch K2SP75_65control leverProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�40GBOperation of the clutch In order to operate the clutches, the electronic control unit of the mechatronics activates the electromagnetic valve • valve 3 of part transmission 1 N435 of the clutch K1 and • valve 3 of part transmission 2 N439 of the clutch K2The clutch is not engaged The piston of the clutch control element is in the rest position. The valve 3 of part transmission 1 N435 opens in the direction of the return flow. The oil pressure stream inflowing from the part transmission 1 passes through valve 4 of the part transmission 1 N436 and flows into the oil reservoir of the mechatronics.Function The example illustrates the operation of the clutch K1.valve N435 of the clutch K1control element of the clutch K1 in the rest positionSP75_66Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB41Hydraulic oil circuitClutch engaged The valve 3 of part transmission 1 N435 is activated by the electronic control unit in order for the clutch to close. Following the activation, the oil channel connected to the clutch control element opens and the oil pressure stream flows behind the pistons of the clutch control element. The piston of the clutch control element moves and as a result the control lever of the clutch K1 is pushed. Clutch K1 is engaged. The electronic control unit of the mechatronics receives a signal from the travel sensor of clutch 1 G617 concerning the exact position of the clutch.valve N435 of the clutch K1control element of the clutch K1 in the rest positionSP75_67Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�42GBNotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB43Transmission control systemSystem overviewmechatronics of the dual-clutch gearbox J743Sensorsgearbox input speed sender G182Gearbox input speed sender 1 G632 Gearbox input speed sender 2 G612Travel sensor of clutch 1 G617 Protected by copyright. Copying private or commercial purposes, in part or in whole, is not permitted Travel sensor of clutch 2 for G618 travel sensor 1 for gear actuator of gear stage G487 travel sensor 2 for gear actuator of gear stage G488 travel sensor 3 for gear actuator of gear stage G489 travel sensor 4 for gear actuator of gear stage G490unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�gearbox hydraulic pressure sensor G270clutch temperature sensor G510Tiptronic switch on the steering wheel E389diagnostic socket44GBCANCANSelector lever E313dash panel insertControl elementshydraulic pump motor V401Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�valve 3 of part transmission 1 N435 valve 3 of part transmission 2 N439valve 4 of part transmission 1 N436 valve 4 of part transmission 2 N440Valve 1 of part transmission 1 N433 Valve 2 of part transmission 1 N434 valve 1 of part transmission 2 N437 Valve 2 of part transmission 2 N438SP75_68GB45Transmission control systemSensors Travel sensor of clutch 1 G617/ Travel sensor of clutch 2 G618The travel sensors of the clutch are located in the mechatronic module above the clutch control element. The operation of the dual-clutch requires a reliable and accurate determination of the current state for closing the clutches. Therefore, a contactless sensor technology is used to determine the position of the clutch. The contactless determination of the position increases the reliability of the function of the sensors. It avoids the distortion of the measured values due to abrasion (wear) and vibrations.G617/G618Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_71Signal application The electronic control unit of the mechatronics uses these signals for operating the control elements of the clutches.Effects of signal failure In the event of signal failure of the travel sensor of clutch 1 G617, the part transmission 1 is disengaged. The 1st, 3rd, 5th and 7th gear stages cannot be engaged. In the event of signal failure of the travel sensor of clutch 2 G618, the part transmission 2 is disengaged. The 2nd, 4th, 6th and R gear stages cannot be engaged.46GBTravel sensor of the clutch Structure The travel sensor of the clutch consists of the following elements: • iron core with primary coil winding • two secondary measuring coils • permanent magnet on the piston of the clutch control element • sensor electronics Function AC voltage is applied to the primary coil. As a result of this, the iron core is surrounded by a magnetic field. If the clutch is closed, the piston of the clutch control element moves together with the permanent magnet through the electromagnetic field. Voltage is induced in the secondary measuring coils resulting from the movement of the permanent magnet. The amount of induced voltage in the left and right measuring coils depends on the position of the permanent magnets. Depending on the amount of voltage in the left and right measuring coils, the sensor electronics identifies the position of the permanent magnets and in turn the position of the piston for the clutch control elements as well.primary coil secondary measuring coiliron coreconnected AC voltagepermanent magnetSP75_72piston of the clutch control elementmeasurement voltagesensor electronicsGBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�47Transmission control systemGearbox input speed sender G182The gearbox input speed sender is inserted in the gearbox housing. Only this sender (sensor) is located outside the mechatronic module. It scans the ring gear of the starter and in this way determines the input speed of the gearbox. The gearbox input speed is the same as the engine speed. The sender G182 works on the Hall sender principle.G182SP75_73Signal application The gearbox input speed signal uses the electronic control unit of the mechatronics for the calculation of slip at the clutches. For this purpose, it compares the signals of the gearbox input speed sender G182 before they are delivered to the clutches, with the signals of the senders G612 and G632 which transmit signals reflective of the rate of rotations of the input shafts.Effects of signal failure In the event of signal failure of sender G182, the electronic control unit of the mechatronics uses the signal from the engine speed sender G28 as a substitute. The engine control unit receives this signal via the CAN databus.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�48GBGearbox input speed sender 1 G632/ Gearbox input speed sender 2 G612Both senders are integrated in the mechatronic module. • The sender G632 scans the pulse wheel that is located on the input shaft 1. The control unit calculates the speed of the input shaft 1 based on the received signal. • The sender G612 scans the toothed pulse wheel located on the input shaft 2. The control unit calculates the speed of the input shaft 2 based on the received signal.Both senders work on the Hall sender principle.G632 G612Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP75_74Signal application The speed signals of the 1st and 2nd input shafts are used by the electronic control unit of the mechatronics for operating the clutch and for the calculation of slip at the clutch.Effects of signal failure In the event of signal failure of the sender G632, the part transmission 1 is disengaged. The 1st, 3rd, 5th and 7th gear stages cannot be engaged. In the event of signal failure of the sender G612, the part transmission 2 is disengaged. The 2nd, 4th, 6th and R gear stages cannot be engaged.GB49Transmission control systemClutch temperature sensor G510The temperature sensor is located directly in the electronic control unit of the mechatronics. The electronic control unit of the mechatronics is constantly moistened by the hot hydraulic oil and is heated in this way. An excessive rise in temperature can impair the electronic functions. The sensor measures the temperature directly in the most vulnerable components. Therefore, measures can be initiated to reduce oil temperature in good time to avoid excessive heat generation in the mechatronics.G510SP75_75Signal application The signal of the sensor G510 is used to check the temperature of the mechatronics. At temperatures in excess of 139 °C, the mechatronics initiate a reduction in engine torque by way of the engine control unit.Effects of signal failure In the event of signal failure of the sensor G510, this fault is entered in the fault memory.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�50GBGearbox hydraulic pressure sensor G270The hydraulic pressure sensor is integrated in the hydraulic oil circuit of the mechatronics and is designed as a diaphragm pressure sensor.G270SP75_76Signal applicationProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Effects of signal failureThe electronic control unit of the mechatronics uses the signal of the sensor G270 to operate the hydraulic pump motor V401. If the hydraulic oil pressure reaches an E-value of approx. 6 - 7 MPa based on the received signal of sender G270, the hydraulic pump motor is switched off. If the pressure drops to approx. 4 MPa, the motor is switched on again.In the event of signal failure of the sensor, the hydraulic pump motor remains in operation. The hydraulic pressure is controlled by the pressure regulator valve.GB51Transmission control systemTravel sensors 1 to 4 of the gear actuators for the gear stages G487 to G490The travel sensors of the gear actuators for the gear stages are located in the mechatronic module. The electronic control unit of the mechatronics uses a signal created in combination with the electromagnets at the selector forks to detect the exact position of the gear actuators for the gear stages.G490 6th and R gear stages G489 5th and 7th gear stagesG487 2nd and 4th gear stagesG488 1st and 3rd gear stagesSP75_77Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Signal application The electronic control unit of the mechatronics uses the gear actuators of the gear stages for its operation, based on the exact position.Effects of signal failure If one travel sensor fails to send its signals, the electronic control unit of the mechatronics does not recognise the position of the respective gear actuator of the gear stage. Therefore the electronic control unit cannot detect if a gear stage was selected or not by the gear actuator of the gear stages and by the selector fork. If the assigned travel sensor fails, the part transmission is disengaged in order to prevent damage to the gearbox.52GBSelector lever E313The selector lever sensor control unit and the control unit of the electromagnets of the selector lever lock are integrated in the selector lever module. Also located within the selector lever sensor control unit are the Hall senders which detect the positions of the selector lever. The position signals of the selector lever and the signals of the Tiptronic operation are sent via the CAN databus to the mechatronics and to the dash panel insert control unit. Signal application The electronic control unit of the mechatronics uses the signal to identify the selector lever position. The signal is used for operating in driving mode (D-R-S or Tiptronic) and for releasing the starter. Effects of signal failure If the control unit does not detect the selector lever position, both clutches are opened.SP75_78Hall sensors for detection of Tiptronic positionHall sensors for detection of selector lever positionTiptronic switches E438 and E439Switching up and down is performed by operating the switches. The switching signals are sent from the steering column electronics control unit J527 via the CAN bus to the mechatronics of the direct shift gearbox J743. Signal application In Tiptronic mode, the switches on the steering wheel can also be tipped for shifting the gears up and down. If the Tiptronic switches on the steering wheel are operated in the automatic mode, the gearbox control unit enters the Tiptronic mode. If the Tiptronic switches on the steering wheel are operated, the gearbox control unit automatically enters the automatic mode after a predetermined time has elapsed.Protected by signal copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Effects of failure unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�E439E438SP75_04If the signal fails, no Tiptronic functions are possible using the steering wheel switches.GB53Transmission control systemControl elements Electromagnetic valves for the control elements of the clutchValve 3 of part transmission 1 N435 Valve 3 of part transmission 2 N439 The electromagnetic valves of the clutch control elements are located in the electro-hydraulic control unit of the mechatronics. They are activated by the electronic control unit of the mechatronics. This control unit regulates the amount of oil needed for the clutch operation. • The valve N435 regulates the amount of oil needed for the clutch K1 • The valve N439 regulates the amount of oil needed for the clutch K2valve 3 of part transmission 1 N435valve 3 of part transmission 2 N439SP75_79Effects of signal failure If one of the electromagnetic valves of the clutch control element fails, the relevant part transmission is disengaged.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�54GBElectromagnetic valves for oil pressure control of part transmissionValve 4 of part transmission 1 N436 Valve 4 of part transmission 2 N440 The electromagnetic valves of the oil pressure control of the part transmission are located in the electro-hydraulic control unit of the mechatronics. Valve N436 regulates the pressure flow of the hydraulic oil which is supplied to the gear actuators of the gear stages and to the clutch control element of part transmission 1. The 1st, 3rd, 5th and 7th gear stages are shifted by means of part transmission 1. Valve N440 regulates the pressure flow of the hydraulic oil which is supplied to the gear actuators of the gear stages and to the clutch control element of part transmission 2.valve 4 of part transmission 1 N436Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�valve 4 of part transmission 2 N440SP75_80Effects of signal failure If one of the electromagnetic valves of the oil pressure control fails, the relevant part transmission is disengaged and only the gear stages of the other part transmission will be selected.GB55Transmission control systemElectromagnetic valves of the gear actuator for the gear stagesValve 1 of part transmission 1 N433 Valve 2 of part transmission 1 N434 valve 1 of part transmission 2 N437 Valve 2 of part transmission 2 N438 The electromagnetic valves of the gear actuator for the gear stages are located in the electro-hydraulic control unit of the mechatronics. The control unit of the mechatronics regulates the quantity of oil supplied to the gear actuators of the gear stages and in turn decides the actual gear stages. • valve 1 of part transmission 1 N433 for 1st and 3rd gear stages • valve 2 of part transmission 2 N434 for 5th and 7th gear stages • valve 1 of part transmission 2 N437 for 4th and 2nd gear stages • valve 2 of part transmission 2 N438 for 6th and R gear stagesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�valve 2 of part transmission 1 N434,valve 2 of part transmission 2 N438,valve 1 of part transmission 1 N433,valve 1 of part transmission 2 N437SP75_81Effects of signal failure If one of the electromagnetic valves of the gear actuator for the gear stages fails, the relevant part transmission is disengaged.56GBhydraulic pump motor V401The hydraulic pump motor is integrated in the electro-hydraulic control unit of the mechatronics. The motor V401 is activated by the electronic control unit of the mechatronics, based on need. If the hydraulic oil pressure reaches an E-value of approx. 6 - 7 MPa based on the received signal of sender G270, the hydraulic pump motor is switched off. If the pressure drops to approx. 4 MPa, the motor is switched on again.SP75_82hydraulic pump motor V401Effects of signal failureIf the motor does not start, the hydraulic pressure drops and the clutches open by the spring force of the press-on discs.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB57NotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�58GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB59Overview of the previously edited service training resourcesNo.1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50DesignationNo.DesignationMono-Motronic Central locking Vehicle alarm Working with wiring diagrams ŠKODA FELICIA Safety of the ŠKODA vehicles Principles of ABS - were not published ABS - FELICIA System for safe start-up with transponder Air conditioning in the vehicle Air conditioning FELICIA 1.6 engine - MPI 1AV Four-cylinder diesel engine Power-assisted steering ŠKODA OCTAVIA 1.9 ltr. TDI diesel engine ŠKODA OCTAVIA Convenience electronic system ŠKODA OCTAVIA Manual gearbox 02K, 02J 1.6 ltr. and 1.8 ltr. petrol engines Automatic gearbox - fundamentals Automatic gearbox 01M 1.9 ltr./50 kW SDI diesel engines, 1.9 ltr./81 kW TDI 1.8 ltr./110 kW and 1.8 ltr./92 kW petrol engines OCTAVIA, CAN BUS databus OCTAVIA - CLIMATRONIC OCTAVIA - safety of the vehicle OCTAVIA - 1.4 ltr./44 kW engine and gearbox 002 OCTAVIA - ESP - fundamentals, design, function OCTAVIA 4 x 4 - all-wheel drive 2.0 ltr. 85 kW and 88 kW petrol engines Radio navigation system - design and functions ŠKODA FABIA - technical information ŠKODA FABIA - electrical systems ŠKODA FABIA - electro-hydraulic power-assisted steering 1.4 ltr. - 16 V 55/74 kW petrol engines ŠKODA FABIA - 1.9 ltr. TDI Unit injection Manual gearbox 02T and 002 ŠkodaOctavia; model 2001 Euro-On-Board-Diagnosis Automatic gearbox 001 Six-speed gearbox 02M ŠkodaFabia - ESP Exhaust emissions Extended service intervals Three-cylinder petrol engines 1.2 ltr. ŠkodaSuperb; Presentation of the vehicle; part I ŠkodaSuperb; Presentation of the vehicle; part Il ŠkodaSuperb; 2.8 ltr./142 kW V6 petrol engine ŠkodaSuperb; 2.5 ltr./114 kW TDI V6 petrol engine ŠkodaSuperb; Automatic gearbox 01V51 2.0 ltr./85 kW petrol engine with balancing shafts and two-stage intake manifold 52 ŠkodaFabia; 1.4 ltr. TDI engine with unit injection system 53 ŠkodaOctavia; Presentation of the vehicle 54 ŠkodaOctavia; Electrical Components 55 FSI petrol engines; 2.0 ltr./110 kW and 1.6 ltr./85 kW 56 Automatic gearbox DSG-02E 57 Diesel engine; 2.0 ltr./103 kW TDI with pump-nozzle units, 2.0 ltr./100 kW TDI with pump-nozzle units 58 ŠkodaOctavia, Chassis and electromechanical power-assisted steering 59 ŠkodaOctavia RS, 2.0 ltr./147 kW FSI turbo engine 60 2.0 ltr./103 kW 2V TDI diesel engine; particle filter with additive 61 Radio navigation systems in the Škoda 62 ŠkodaRoomster; Vehicle presentation part l 63 ŠkodaRoomster; Vehicle presentation part lI 64 ŠkodaFabia II; Vehicle presentation 65 ŠkodaSuperb II; Vehicle presentation part l 66 ŠkodaSuperb II; Vehicle presentation part lI 67 2.0 ltr./125 kW TDI diesel engine wit