TECHNICAL DOCUMENTATION

SSP 077 Geometry

PDFEN36 pages1 MB
SSP 077 Geometry - PDF cover

This PDF is currently unavailable.

Read document text
ServiceGeometry77Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Service Training In line with the trend of the current development of vehicles, the manufacturers must respond to the ever increasing demands on the driving characteristics. Even in the lower classes of vehicles, we encounter among other things, the independent multi-link rear suspension. The demands on the driving stability and thereby also on the safety, the comfort and the driving dynamics are often in conflict with the needs of a small assembly room and especially with the low cost of production. Modern types of chassis reflect the efforts which are undertaken to resolve the conflicting requirements on the low mass, yet ensuring a high strength of the suspension and at the same time a precise wheel guidance. As a result, aluminum alloys are increasingly and widely used, thus replacing the original steels. Further options for improving the driving characteristics are offered, such as various electronic systems ABS, EDL, ESP, EBD, TCS, which have the task to ensure the optimum transfer of the driving and braking force onto the roadway, the desired behaviour in curves (in most cases mild understeer) etc.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 2 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB ContentsIntroduction Types of axles Front axle McPherson Trapezoidal axle Rear axle Crank axle Multi-link suspension with fixed axle carrier (subframe) Multi-link suspension with auxiliary frame Multi-link suspension LDQ Basic wheel geometry Toe-in Angle of spread, camber Castor angle Wheel steering angle Toe-in constant "S" – toe-in curve Adjustment points of the axles McPherson front axle Trapezoidal-link front axle Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Rear axle unless authorised bycrank ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Multi-link rear suspension The conditions for the inspection and the preparation for measurement The conditions for the inspection The preparation for the measurement Jack tolerance Consequences of poor geometry Design modifications of the Škoda vehicles over the course of their production 4 5 5 6 7 8 9 10 11 11 12 13 14 15 16 16 18 20 21 24 25 26 28 29 31You will find the notes for the assembly and disassembly, repair, diagnostics as well as detailed user information in the diagnostics, measuring and information system VAS 505x. The time for going to press was on the 12/2009. This brochure is not subject to an update.GB3 IntroductionThe term chassis refers to the part of the vehicle which ensures that the vehicle is capable of moving on the roadway. It consists of several parts: • rims with tyres • wheel suspension • shock absorbtion • steering • brake system The geometry of the chassis primarily applies to the suspension of the wheels. Therefore, we will continue to address precisely this problematic issue. In practice we often encounter the term axle. It comprises both the suspension of the wheels and their bearing, as well as the brakes, the shock absorbtion and the drivetrain, possibly also the powertrain. The actual wheel suspension consists of parts that attach the wheels to the body or to the vehicle frame. Their task consists in facilitating their vertical movement relative to the body, which is required for the spring deflection and to drive the wheels into an optimum position relative to the roadway.SP77_234Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB Types of axlesMcPherson front axleOn all Škoda vehicles, starting with the model Favorit, with the exception of the ŠkodaSuperb model of the first generation, the proven kinematically independent suspension of the McPherson type was used for the powered front wheels. On each side of the axle is a wishbone and a damper unit which guide the wheel. The Yeti model and the Octavia and Superb models of the second generation have a front axle bearing on an aluminum subframe. Thereby improving the elastokinematic properties while reducing at the same time the mass of the axle.Head end of the wheel pivot bearingPower steering gearSteering rod Anti-roll bar ConsoleDamper unitProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Wheel bearingTrack control armRocker armSP77_8Subframe Anti-roll barGB5 Types of axlesTrapezoidal-link front axleEach wheel of the trapezoidal-link front axle on the ŠkodaSuperb model of the first generation is steered by a steering rod and four suspension arms independent of each other. The subframe is fixed to the body by means of high-volume rubber-bonded metal bearings. The coil spring and the jacketed gas/liquid-filled shock absorber form the damper unit. This type of axle makes it possible to eliminate the influences of the powertrain on the steering almost entirely, which offers a comfortable and safe drive. It is easy to operate and allows an accurate straight line alignment of the axle. Its design ensures a neutral to a mildly understeering behaviour of the vehicle.Bearing bodyDamper unitPower steering gearrear upper arm front upper armBearing head of the wheel pivotEngine bearer lower guide arm Subframe lower support armPipe stabiliserSP77_46Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB Rear crank axleThe ŠkodaFabia models of both generations feature a rear axle design which is proven and commonly used. It is a crank axle, consisting of two trailing arms connected by a torsion arm type suspension. The body of the axle is nestled at the front (in driving direction) on either side in rubber-bonded metal bearings, which secure the axle in the body. In the lower part, the springs are anchored in two steel bearings attached to the trailing arms. The upper part of the springs is supported by the longitudinal crossbeam of the body, which contributes to a reduction of noise transmission within the passenger compartment. The telescopic dampers are located behind the springs (in driving direction). The same principle of the wheel suspension applies to the models ŠkodaRoomster, ŠkodaOctavia of the first generation with front-wheel drive and the ŠkodaSuperb model of the first generation.Anchor point of the bodyShock absorberCoil springTrailing armProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Rubber-bonded with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�metal bearingTorsion barSP77_5GB7 Types of axlesMulti-link rear suspension with fixed subframeA multi-link rear suspension was developped for the ŠkodaOctavia model of the second generation. It gives the vehicle excellent driving characteristics and ensures more stability in extreme situations. The multi-link rear suspension consists of four arms on each side, namely the: • upper transverse control arm • lower transverse control arm • connecting control arm • trailing arm This design solution makes it possible to respond optimally to the longitudinal and transverse forces which are applied. Three transverse control arms ensure the dynamics in the transverse direction. Their precisely defined bearing enables the accurate setting of the required operating regimes. The subframe is firmly secured to the body (only vehicles with front-wheel drive).lower transverse control arm Cylindrical coil spring Upper transverse control arm Anti-roll bar Shock absorberWheel bearingBearing mountingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Connecting control arm Subframe Head end of the wheel pivot bearingTrailing armSP77_98GB Multi-link rear suspension with auxiliary frameThe models ŠkodaOctavia II 4x4, ŠkodaSuperb II and ŠkodaYeti are fitted with the modified multi-link suspension which was first introduced in the ŠkodaOctavia II model. The modification consists in replacing the fixed subframe by an auxiliary frame which is connected to the body via elastic bearings. Furthermore, strong aluminium head pieces of the wheel pivot bearing are used on the Yeti model, which are also installed on the VW Passat model, whereby an extension of the axle by about 30 mm was achieved. The auxiliary frame is used on the models ŠkodaSuperb of the second generation and ŠkodaYeti regardless of whether they have rear-wheel drive or not. Current version of the axle with a steel auxiliary frame:Shock absorberFlexible fastening bearing upper transverse control arm Bearing mountingAnti-roll bar Connecting control arm Auxiliary frame Trailing armSP77_10Original version with an auxiliary frame and a reinforced crossbeam made of an aluminum alloy as used on the first Octavia II 4x4 models:Auxiliary frameProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�CrossbeamSP77_24GB9 Types of axlesMulti-link rear suspension (LDQ axle)The ŠkodaOctavia models of the first generation are equipped with a multi-link suspension, which is known as the LDQ axle. It consists of two trailing arms attached to the body and four suspension arms attached to the auxiliary frame, which in turn is mounted on the body via an elastic bearing just as the trailing arms. An anti-roll bar is also attached to the subframe. The shock absorbers are located behind the springs and have an angle of inclination of about 45° compared to the version with a classic crank axle.Anti-roll bar Shock absorberCrossbeamAuxiliary frameHaldex coupling Rubber-bonded metal bearing Trailing arm of the rear axle Transverse control armSP77_11Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�10GB Basic wheel geometryWe describe the position of the wheels relative to the roadway and to the base planes of the vehicle using the individual parametres of the wheel geometry. Amongst the main parametres of the wheel geometry are: • toe-in δ • angle of spread σ • camber angle γ • castor angle τ • wheel steering angle α, β, ε All the main parametres can be measured on the steered axle of the vehicle, on non-steered axles we measure only: • toe-in δ • camber angle γToe-inThe toe-in δ refers to the angle between the centre planes of the wheels. The wheel has a toe-in angle (convergent), provided that the front part of the wheel is inclined to the longitudinal axis of the vehicle. In general, the toe-in is measured as an angle deviation or in units of length on a well-defined point of the wheels.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�VY XδSP77_1GB11 Basic wheel geometryAngle of spreadThe angle of spread σ is the angle projected onto the transverse plane of the vehicle between the steering axis and the vertical axis of the vehicle. It ensures the tilting moment which brings the wheel back to the straight-ahead position. The higher the value of the angle of spread, the greater is the force needed to turn (rotate) the wheels. Herewith, the distance projected on the transverse plane of the vehicle from the centre of the wheel contact area to the point of intersection of the steering axis also relates to the plane of the roadway. This is called kingpin offset (offset steering) r. When it is outside the centre plane of the wheel, it is considered to have a negative offset. The sensitivity of the axis to the longitudinal forces augments when the offset steering increases, so that a negative offset steering is applied in order to stabilise the steering. The forces needed to turn (rotate) the wheels augment when the offset steering increases, either to a positive or also to a negative offset, provided the vehicle is stationary or moving slowly.Camber angle (camber)The camber angle γ refers to the angle between the vertical axis of the vehicle and the centre plane of the wheel. The camber angle is a positive value, provided the top of the wheel inclines outwards from the vehicle. Wheels which have a positive camber angle reciprocally counteract each other, whereby they reduce the tendency for steering oscillation (vibration) in a straight-ahead position and limit the play in the wheel bearings.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�γσZ YrSP77_212GB Castor angleThe castor angle τ is the angle projected onto the longitudinal plane of the vehicle between the steering axis and the vertical axis of the vehicle. The castor angle has a stabilising effect on the steering wheel, this makes it possible to bring the wheel back to the straight-ahead position and dampens the effect of steering vibrations.VτZ XProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP77_3GB13 Basic wheel geometryWheel steering angle (steering angle)The steering angles α and β refer to the turning of both wheels of the steered axle. To ensure that the wheels of the vehicle do not slip when driving through a curve, the axes of both steered wheels must intersect on the mutual axis of the wheels of the rear axle. As a consequence, the wheel closest to the centre of the curve must turn more than the wheel which is further away. The difference between both angles is called a difference angle ε.βVεαXαYεβProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�αSP77_25 GB14 Toe-in constant "S" – toe-in curveIf the wheel bounces up and down, a change in toe-in occurs depending on the extent of spring deflection. When a change in toe-in of the front axle occurs, this helps to improve the driving safety. As a result of the acceleration, load is relieved and in this way the front axle is raised. The geometry of the suspensions is designed so that in this case the value of the toe-in increases. The front part (nose) of the vehicle dips down when braking and the toe-in decreases because the divergence of the wheels increases. This assists the braking effect. When driving through a curve, the outer wheel undergoes the divergence change due to the inclination angle of the vehicle, while the inner wheel undergoes the convergence change (toe-in) which increases the understeer behaviour of the vehicle. The toe-in values which are determined by the different spring deflections create the so-called toe-in curve. The axle alignment device determines the toe-in constant "S" as a difference between the toe-in values measured in the initial position and in the raised position. In so doing, the nominal values are compared to the actual values, which are displayed on the monitor. Different adapters are required for raising the chassis depending on the height and tuning (standard, sport or chassis with increased clear width). In contrast to all the other Škoda models, the toe-in constant is measured only on the Superb model of the first generation which is the only model fitted with a front axle with trapezoidal suspension, developped for the chassis platform B of the fifth generation.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB15 Adjustment points of the axlesMcPherson front axle Camber angle (camber)On the front axle of this type, the camber angle of both wheels can be set independently. By shifting the subframe on the left or on the right, the camber can only be compensated for in such a way that it is equal on both sides. The subframe can be shifted after slackening four, if necessary six fixing screws (depending on the type). Warning! When setting the camber angle of the wheels of the front axle, the subframe must simply be shifted to the side. When shifting the subframe to the front or to the rear, a castor change occurs and respectively the inclination of the steering axis changes! Always use new screws when attaching the subframe!Octavia ISP77_12Octavia II, Superb II, YetiSP77_13Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�direction of shift of the subframe fixing screwsFabia I and II, RoomsterSP77_1416GB Castor angle(only Octavia II, Superb II and Yeti) Setting the castor angle of the front wheel or its steering axis is performed by moving the body of the rear bearing for the lower transverse control arm of the suspension. As a result of this, the leg rotates around its front bearing. The steering pivot which is mounted in this leg, then moves in the longitudinal direction thus changing the angle of the steering axis.SP77_15Toe-inOn most types of suspensions, setting the toe-in of the wheels of the steered axle is performed Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted simply by changing the length of the steering unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability rods. Inwith practice, this means the counternut respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� must be slackened and the steering rod must be unscrewed or screwed into the head end by turning the hexagon, thus changing the distance between both hinges.SP77_16change the length of the steering rod by turning the hexagon direction of movement of the bearing fixing screws (SP77_15), nut (SP77_16)GB17 Adjustment points of the axlesTrapezoidal-link front axleCamber angle (camber)The camber angle of both wheels cannot be set independently on the trapezoidal-link front axle just as on the axle with the McPherson suspensions. By shifting the subframe on the left or on the right, the camber can only be compensated for in such a way that it is equal on both sides. The subframe can be shifted after slackening the eight screws with which it is attached to the body.SP77_17Toe-inSetting the toe-in on the trapezoidal-link front axle of the ŠkodaSuperb model of the first generation is performed in the same way as on the axles with McPherson suspensions. Thus, by turning the steering rods by means of the hexagon after releasing the counternuts.hexagon of the steering rod fixing screws (SP77_17), counternuts (SP77_18) SP77_18Toe-in constant "S"Changing the toe-in constant "S" is done by movProtected copyright. Copying for a private or commercial purposes, in part or in whole, is not permitted ing the head end of the by steering rod in vertiunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability cal direction to the head end of the wheel pivot with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� bearing. This change is carried out on a raised axle, which rests on a device at the point of the screws marked in the figure which in turn secure the subframe to the body. The lifting height is 65 mm from the base position.SP77_2618GB The clamp connection slackens by loosening the nut -A-. The adjusting screw -B- is screwed out by approx. 4 mm. The head end of the steering rod is fully pressed onto the screw -B-, which shortens its location (distancewise) relative to the entire wheel suspension. Through gradual tightening of the new adjusting screw, its position can be adjusted in such a way that the toe-in corresponds to the desired value when the axle is raised. After tightening the nut -A- as well as the screw -B- the axle returns to its basic position in which the toe-in is checked once more.Screw -BNut -A-BASP77_19Note The setting of the toe-in or the S-curve must precede the alignment of the rack pinion in the steering gear! If the rack pinion is not exactly positioned in the centre when the vehicle is in the straightahead position, the vehicle will pull to one side with the constant slight aid of the hydraulic steering system. The alignment is performed by means of the screw – V.A.G 1907– which is screwed into the body of the steering gear after removing the hexagon socket head cap -1- from the thread opening. Subsequently, the steering wheel can be brought into the horizontal position.1 12 2V.A.G. 1907V.A.G. 1907SP77_27Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB19 Adjustment points of the axlesRear crank axleCamber angle (camber)The camber angle on the rear axle of this type cannot be set. If the camber values are outside the tolerance and the conditions for the inspection are met, check the body of the axle for damage and if necessary replace.Octavia I, RoomsterSP77_20Toe-inOn the models Fabia l and ll, the toe-in at the rear axle cannot be set. If the camber values are outside the tolerance and the conditions for the inspection are met, check the body of the axle for damage and if necessary replace. On other vehicles fitted with a crank axle, the attempt can be made to compensate for toe-in evenly by moving the bearing mountings in the frame of their oval openings through which they are attached to the body.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�direction of movement of the bracketSuperb ISP77_2820GB Multi-link rear suspension Camber angle (camber)The camber angle of the wheels for the multi-link rear suspension is set independently on both sides. This is achieved by turning the eccentric screw -a-, which secures the upper control arm to the subframe or the auxiliary frame. In this way, the centre of rotation of the upper leg moves in the transverse direction -b- and in turn the head end of the wheel bearing -c-.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP77_29View from the front of the axle of the Yeti model, which has been removed from the body for the purpose of illustration.GB21 Adjustment points of the axlesAfter setting the desired camber, the nut -dmust be replaced with a new one and tightened to the prescribed tightening torque.view from behindSP77_30It is recommended to use the device -T10179- for loosening and subsequently tightening the nut -dbecause of the dif ficult access.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�device –T10179–SP77_3122GB Toe-inThe toe-in angle of the wheels for the multi-link rear suspension is set independently on both sides. This is achieved by turning the eccentric screw -a-, which secures the lower control arm to the subframe or the auxiliary frame. In this way, the centre of rotation of the leg moves in the transverse direction -b- and in turn the head end of the wheel bearing -c-.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�view from below the axle of the YetiSP77_32After setting the desired camber, the nut -d- must be replaced with a new one and tightened to the prescribed tightening torque.GB23 The conditions for the inspectionIn general: • The vehicle must only be measured on a test stand, which was approved for use by the manufacturer. • The front and the rear axles must be measured each time the vehicle is measured. Otherwise, the correct driving characteristics cannot be ensured! Note: • The measurement of the vehicle is intentionally performed only after 1000 to 2000 kilometres driven, because only then the discharging process of the coil springs is completed. • One cause of the vehicle shaking may be a too large residual imbalance of the wheels and/or they may be running out of true. • During the measurement steps, the desired values should be achieved with utmost precision.Failure to comply with the mounting position of the rear axle can appear as if the steering wheel is slanted. The vehicle then moves in the direction of the slanting angle of the rear wheels and the steered axle has to compensate for this deflection when the vehicle is in the straight-ahead position. Note for the disassembly of the steering wheel:V Y X• Before disassembling the steering wheel, mark the position of the by steering wheel Protected copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability relative to the steering column, if neceswith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� sary pay attention to the already existing marking. • This position must be not changed! Otherwise, the centre position of the rack pinion cannot be ensured! • The steering columns, which are supplied as spare parts, have no marked centre position. They are only marked after the measurement of the vehicle and a subsequent test drive. • Vehicle with ESP: If the steering weel is changed on this vehicle, the basic setting of the steering angle sender –G85– must be checked → diagnostics, measuring and information system VAS 505x.SP77_3424GB The vehicle must be measured, if:• it shows deficiencies in the driving characteristics, • after an accident, the specific vehicle parts mentioned in the corresponding table in the workshop manual were replaced, • the specific vehicle parts mentioned in the corresponding table in the workshop manual were disassembled or replaced, • on the vehicle, for example, a tyre that is worn on one side is noticed.The conditions for the inspectionThe actual measurement and adjustment of the vehicle must be preceded by the following steps: • Determin the type of the chassis on the basis of the data plate, possibly from the ELSA system. • Check, the wheel suspension and the wheel bearing, the steering and its parts for impermissible play and damage, if necessary repair. • Check the depth of the tread pattern. The difference in depth on an axle must not exceed 2 mm. Inflate the tyre to the required pressure. • Fill the fuel tank to the maximum, possibly counterbalance using sandbags. • Check whether the spare wheel and the vehicle tool kit (depending on the equipment) are in their specific place. • Fill the windshield washer system reservoir to the maximum. • Proper alignment of the vehicle, multiple spring deflection and stabilisation. While measuring, none of the movable parts of the measurement system designed for measuring must move into the final position or strike! Very important! Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted • Pay attention to the standard preparation and of measurement you unless authorised by ŠKODA AUTO A. S. setting ŠKODA AUTO A. the S. does not guarantee or accept system; any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� must operate the system in accordance with the user manual! Likewise, you may ask the manufacturer of the measurement system for instructions. It is possible that the settings of the platforms and the computer for the measurement of the axle differ over time from the original setting for leveling. As part of the maintenance, but at least once a year, the platforms and the computer for the measurement of the axles should be checked and set! Work carefully and conscientiously with these very sensitive devices!GB25 The preparation for the measurementThe preparation for the measurement• To avoid false measurement results, the axial run-out compensation (balancing) procedure of the rim must be carried out. Otherwise, the measurement result would not be correct. The toe-in of the wheels cannot be correctly set without carrying out the axial run-out compensation procedure of the rims! • Position the device for pressing the pedal, e.g. -V.A.G 1869/2-, for securing the brake pedal Required special tools, inspection and measuring devices as well as auxiliary means • Device for pressing the pedal, e.g. -V.A.G 1869/2• System for measuring the axles • Weights, for example sandbags with a mass of 10kg eachSP77_21Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�26GB Check the transverse gradient of the vehicle "zero position"If the measured values are outside the tolerance of the nominal values, this may be caused by the slanting angle of the vehicle body. Vehicles with the steering wheel on the right-hand side or for example vehicles with an automatic gearbox may have a somewhat slanted angle. This is a normal condition due to the location of the unit and the related mass distribution. • Check the dimension -a- on the left and right at the front axle (Octavia II, Superb II, Yeti) as well as at the rear axle (all Škoda models except Superb I). • Correct possible deviations from the specified value. The values of the dimension -a- can be found in the workshop manual of each vehicle.aSP77_22On the front axle, the difference may be offset by placing a weight on the respective bearing of the shock absorber unit in the engine compartment. On the rear axle, the difference may be offset by placing a weight on the relevant side in the luggage compartment. For example, sandbags of 10 kg each can be used as a load.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�10kgSP77_36 GB27 The preparation for the measurementOverview of the working steps for the measurement of the vehicleThe following sequence of the working steps must be kept! 1. Determine the chassis type on the vehicle. This information is provided in the data plate. 2. Carry out the compensation operation for the axial run-out of the rim. 3. Deflect the vehicle. 4. Position the device for pressing the brake pedal, e.g. -V.A.G 1869/2-. 5. Measure the height of the vehicle, possibly the offset of its transverse gradient by placing weights. 6. Lock the steering wheel in the middle position of the height adjustment of the steering column. 7. Set the centre position of the rack pinion and secure the steering wheel (by securing the rack pinion in the centre position, the same diametre for cornering the vehicle is ensured on both sides). If the steering wheel is slanted, it must be brought into the correct position after completing the measurements (in a straight position). 8. Check, if necessary set the camber at the front axle. 9. Check, if necessary set the camber at the rear axle (only Octavia II, Superb II and Yeti). 10. Check, if necessary set the toe-in at the rear axle (not valid for Fabia). 11. Check, if necessary set the castor angle at the front axle (only Octavia II, Superb II and Yeti). 12. Check, if necessary set the toe-in at the front axle. 13. Check, if necessary set the toe-in constant at the front axle (only Superb l).Jack tolerance |±1mm| |±1mm| |±2mm|SP77_35Compared to the usual jacks, higher demands are placed theisaccuracy Protectedlifting by copyright. Copying for private or commercial purposes, in part or on in whole, not permitted of the lifting facilities unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability used when checking the geometry. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� This refers in particular to the tolerance of the sole of the plane, whereby the difference in height between the left side and the right side of the front or rear axle must not be greater than 1 mm. When measuring diagonally, the difference in height must only be 2 mm between the front right side and the rear left side or vice versa. These tolerances are valid for each measurement position! They are checked on four-column as well as scissor lift facilities.28GB Consequences of poor geometryA poor geometry of the vehicle does not only cause rapid and uneven tyre wear. A more serious consequence is the deterioration of the driving stability and the longer brake path. If the geometry is correctly set, this helps to reduce the fuel consumption and to lower the exhaust emissions due to the lower rolling resistance.Camber angle (camber)A reduced camber angle increases the wear of the inner edge of the tyre, whereas an increased camber angle in turn increases the wear of the outer edge of the tyre. An asymmetrical camber angle of the left axle and the right axle causes the vehicle to pull to the side where the wheel has a larger camber angle. It is difficult to keep the vehicle in the straightahead position.Unsymmetrische Abnutzung des ReifensSP77_37Castor angleA reduced castor angle leads to unsafe steering behaviour. The vehicle seems to "float" so to speak, on the road. The wheels do not tend to return to the straight-ahead position. However, increasing the castor angle stabilises the vehicle travelling straight ahead while increasing the forces needed to deflect the vehicle from the straight-ahead position.Toe-inDiagonale Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�If the toe-in is reduced, the vehicle "floats", as it requires a constant correction by the steering wheel to hold the vehicle in the desired direction. The tyres wear excessively and this causes wheel vibrations. An increased toe-in is characterised by the difficulty to deflect the vehicle from the straightahead position and by the rapid return of the wheels after driving through a curve. Once again the tyres wear excessively, especially on the outside surface of the tread. On the rear wheels of the vehicles with a front drive axle, we can see in some places diagonal wear of the tyre.Abnutzung des ReifensSP77_38And in cases of an excessively large toe-in angle, if the rear wheel slides slightly laterally while rolling. The increased distortions of the tyre are eliminated by the sliding friction occuring always at the same point of the tread, whereby creating a diagonal strip of an excessively used tread pattern.GB29 Consequences of poor geometryVariable toe-inA different setting of the toe-in curve of the left wheel from the right wheel, and thus changing the toe-in settings of both wheels differently by way of their spring deflection, can result in the vehicle deflecting from its direction when driving over bumps on the roadway and in a worse case, even when accelerating or braking. The influence of the vehicle tilting to the side when cornering leads to the instability of the vehicle. The actual travel path of the vehicle does not correspond to the turning angle of the steering wheel. Note An excessive wear of the tyres can only be caused by the poor geometry of the vehicle. In practice, we notice the wear of the tyres from driving with a too low or to the contrary, a too high tyre pressure.Tyre wear at low pressureSP77_39Tyre wear at overpressureSP77_40A further wear, which is not directly caused by the geometry of the chassis, is the so-called sawtooth-shaped wear of the tread pattern. The single tyre tread blocks become deformed during rolling. At the outset of the contact with the road surface, they are pressed together and when leaving the point of contact they are rubbed off as they return to their original shape and size. Thus, a greater wear occurs on the rear side of the tread blocks. If the height difference between the front and rear edges of the tread blocks is not greater than 0.8 mm, a significant deterioration in the properties of the tyres, with the exception of the increased noise while driving, does not occur.Original shape of the tread blocks Shape of the blocks after wearSawtooth-shaped wear in the cut of the tread patternSP77_41Sawtooth-shaped wear occurs mostly on the non-drive axle, whereas it is primarily noticeable in the shoulder part of the tyre. Triangular areas of the worn tread pattern, which look like saw teeth, arise depending on the tread shape of the transverse ridges. If it is a directional tread pattern and the tyre cannot be turned around on the rim, the wheels should be changed with the drive axle and the non-drive axle after approx. 10000 kilometres driven. The reason is usually an incorrect tyre pressure, aided by an excessively large toe-in angle.30GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Design modificationsDesign modifications of the Škoda vehicles over the course of their production Fabia II, Roomster – front axleThe vehicles produced up to the 11th week of 2008 had a front subframe with mounted consoles. The subframe was available in two versions depending on the engine equipment, due to the different exhaust management system. On the more recent models, a welded one-piece subframe without consoles is used, which corresponds to both exhaust management systems. Furthermore, the lower leg, the ball joint and the head end of the wheel pivot bearing have been modified.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP77_42Original solution of the subframe with mounted consoles. The ball joint heads are inserted into the profile of the lower legs and are secured from below using screws which are screwed into the nuts in the securing plates (not shown) on the top side of the leg.SP77_42New subframe with integrated consoles. The ball joint heads with weld screws are inserted at the top in the openings in the lower legs and secured by nuts from below.GB31 Design modificationsSince January 2009, the attachment of the shock absorber units in the housings within the body was modified. Both units are shown without the grommets and the elastic stop collars.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP77_44SP77_45Original shock absorber unit secured to the body by means of three screws in the rivet nuts within the rubber-bonded metal bearing.With the new solution, the shock absorber unit inserted in the housing within the body is secured to the piston rod of the shock absorber by means of one self-locking nut.32GB Octavia II – rear axle 4x4As of 06/2007, the original aluminum subframe was replaced by a steel frame on the 4x4 vehicles. In this context, the crossbeam under the steering device including the connecting material were omitted.SP77_46Protected by copyright. for private or commercial purposes, in part or in whole, is not permitted Original aluminum subframe with Copying mounted crossbeam. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP77_47At present, the subframe does not require a crossbeam for reinforcement.GB33 On the same date, the head end of the wheel pivot bearing made of cast steel was replaced with an aluminium head. In this context, the cover plate of the brake disc was also changed and is now secured with four screws instead of three.SP77_46Original steel head end of the wheel pivot bearingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP77_46Current version of the head end of the wheel pivot bearing made of an aluminum alloy.34GB NotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Overview of the previously edited service training resourcesNo.Designation1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Mono-Motronic Central locking Vehicle alarm Working with wiring diagrams ŠKODA FELICIA Safety of the ŠKODA vehicles Principles of ABS - were not published ABS - FELICIA System for safe start-up with transponder Air conditioning in the vehicle Air conditioning FELICIA 1.6 engine - MPI 1AV Four-cylinder diesel engine Power-assisted steering ŠKODA OCTAVIA 1.9 ltr. TDI diesel engine ŠKODA OCTAVIA Convenience electronic system ŠKODA OCTAVIA mech. gearbox 02K, 02J 1.6 ltr. and 1.8 ltr. petrol engines Automatic gearbox - fundamentals Automatic gearbox 01M 1.9 ltr./50 kW SDI diesel engines, 1.9 ltr./81 kW TDI 1.8 ltr./110 kW and 1.8 ltr./92 kW petrol engines OCTAVIA, CAN BUS databus OCTAVIA - CLIMATRONIC OCTAVIA - safety of the vehicle OCTAVIA - 1.4 ltr./44 kW engine and gearbox 002 OCTAVIA - ESP - fundamentals, design, function OCTAVIA 4 x 4 - all-wheel drive 2.0 ltr. 85 kW and 88 kW petrol engines Radio navigation system - design and functions ŠKODA FABIA - technical information ŠKODA FABIA - electrical systems ŠKODA FABIA - electro-hydraulic power-assisted steering 1.4 ltr. - 16 V 55/74 kW petrol engines ŠKODA FABIA - 1.9 ltr. TDI Unit injection Mechanical gearbox 02T and 002 ŠkodaOctavia; model 2001 Euro-On-Board-Diagnosis Automatic gearbox 001 Six-speed gearbox 02M ŠkodaFabia - ESP Exhaust emissions Extended service intervals Three-cylinder petrol engines 1.2 ltr. ŠkodaSuperb; Presentation of the vehicle; part I ŠkodaSuperb; Presentation of the vehicle; part Il ŠkodaSuperb; 2.8 ltr./142 kW V6 petrol engine ŠkodaSuperb; 2.5 ltr./114 kW TDI V6 petrol engine ŠkodaSuperb; Automatic gearbox 01VNo.Designation51 2.0 ltr./85 kW petrol engine with balancing shafts and two-stage intake manifold 52 ŠkodaFabia; 1.4 ltr. TDI engine with unit injection system 53 ŠkodaOctavia; Presentation of the vehicle 54 ŠkodaOctavia; Electrical Components 55 FSI petrol engines; 2.0 ltr./110 kW and 1.6 ltr./85 kW 56 Automatic gearbox DSG-02E 57 Diesel engine; 2.0 ltr./103 kW TDI with pump-nozzle units, 2.0 ltr./100 kW TDI with pump-nozzle units 58 ŠkodaOctavia, Chassis and electromechanical power-assisted steering 59 ŠkodaOctavia RS, 2.0 ltr./147 kW FSI turbo engine 60 2.0 ltr./103 kW 2V TDI diesel engine; particle filter with additive 61 Radio navigation systems in the Škoda 62 ŠkodaRoomster; Vehicle presentation part l 63 ŠkodaRoomster; Vehicle presentation part lI 64 ŠkodaFabia II; Vehicle presentation part 65 ŠkodaSuperb II; Vehicle presentation part l 66 ŠkodaSuperb II; Vehicle presentation part lI 67 2.0 ltr./125 kW TDI diesel engine with Common Rail injection system 68 1.4 ltr./92 kW TSI petrol engine with turbocharger 69 3.6 ltr./191 kW FSI petrol engine 70 All-wheel drive with Haldex coupling of the lV generation 71 ŠkodaYeti; Vehicle presentation part l 72 ŠkodaYeti; Vehicle presentation, part ll 73 LPG system in Škoda vehicles 74 1.2 ltr./77 kW TSI petrol engine with turbocharger 75 Automatic 7-speed gearbox with double clutch 0AM 76 Greenline vehicles 77 Geometryunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Only for the internal use in the service network ŠKODA. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� All rights and technical modifications reserved. This paper was made out of S00.2002.77.20 E GB Technical status 12/2009 chlorine-free bleached cellulose. © ŠKODA AUTO a.s. http://portal.skoda-auto.comProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted77