TECHNICAL DOCUMENTATION

SSP 078 Passive safety

PDFEN36 pages2 MB
SSP 078 Passive safety - PDF cover

This PDF is currently unavailable.

Read document text
ServicePassive safety78Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Self-study programme Percentage representation of the frequency of accident impact pointsMost often frontal collisions occur during accidents; second in the statistics of crash frequency are accidents in which the rear of the vehicle is affected. The side impact crashes that occur in the remaining cases represent in total 25% of the accidents, which is a negligible share. Therefore, a complex system of passive safety is integrated in Škoda vehicles, which serves to mitigate the consequences of the above mentioned spectrum of accidents. When developing the elements of passive safety, the company Škoda Auto places a great importance on the protection of all participants in road traf fic, this is why Škoda vehicles are also equipped with systems for the protection of pedestrians. This brochure provides an insight into the individual passive safety systems.60%4.5%3%10%1%Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�5%1.5%15%SP78_062GB ContentsSafety development Safety arrangement Body Seat belts AirbagsGas generators Driver airbag Front passenger airbag Side airbag Head airbag Knee airbag4 5 6 8 13 18 20 21 22 23 24 25 26 27 29 30 32 33 34 35Interruption of current conductor SeatsSupports Child seatsSteering column Pedals Glass fillings Exterior safety EURO NCAPThe time for going to press was on the 12/2009. This brochure is not subject to update.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB3 Safety developmentAutomobiles were designed for a long time without regard to the safety of the occupants and the safety of other road users. In the 1950's researchers at an American University in Detroit made history by developing passive vehicle safety. General automotive design rules were established to ensure the safety of the occupants. The rules that were created on the basis of the tests led to the design of vehicles offering a very solid cabin, free of any projections and with sufficiently large crumple zones to absorb the motion of the impact.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The picture shows Larry Patrick, a professor at Wayne State University in Detroit, who carried out some tests directly on himself.SP78_044GB Safety arrangementPassive and active safetyThe safety concept consists of two groups, active and passive, depending on the design elements used in the vehicle.Passive safetyThe elements that are part of the complexity of passive safety systems, have no influence on the function and operation of the vehicle. Their task is to protect the occupants and other traffic participants in an accident.Active safetyThose elements that belong to the active safety system have a direct influence on the function of the vehicle and its operation while driving. Because of the complexity of these elements, it is possible to prevent accidents.Design elements of passive safety:interior safety (protection of the occupants) • crumple zones of the body • high-strength steel as a structural element of the body • Airbags • Seat belts • corrugated tube of steering wheel made of deformable material • floating seats • design of the pedals • soft synthetic materials used in the vehicle interior • rounded edges • head restraints • child seats • interruption of fuel supply in case of an accident • switching on the headlights and opening the locks in case of an accident exterior safety (protection of the pedestrians) • rounded corners on the body • resilient bumpers • deformation properties of the body • shape of exterior door handles • adjustable mirrors • shape of window wipers • hub caps • shape of headlightsDesign elements of active safety:• ABS - anti-lock braking system • ESP - electronic stability program • MBA - mechanical brake assistant • EBV - electronic braking force distribution • active body control • four-wheel drive • parking sensors • xenon headlights • brake pad monitoring • automatic dimming mirror • size and shape of the rear view mirror • recognition of a vehicle in the blind spot of the mirror • automatic door locking while driving • signal of unfastened seat belts • control elements on the steering wheel • rain sensor • window wipers • air conditioning system • quality tyres • navigation • steering aid • automatic gearbox • hands-free systemGBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�5 BodyRigidity of the body and the crumple zoneThe design and development work is carried out using modern mathematical calculations and models, through which optimum profiles of the body can be achieved to guarantee a great rigidity with relatively low weight. The force absorbing capability of the crumple or deformation zones has been optimized, in order to minimize the impact forces transmitted through the vehicle in the event of a frontal or offset collision. The monocoque body of a vehicle considerably improves the efficiency of the impact-absorbing crumple zones, whilst the vehicle deforms according to a deceleration-time response. In addition to sheet metals with various strengths, shape-matching deformation elements are also used. It is important to create a zone which is very rigid and firm in the transverse direction, yet on the other hand it should be supple in the longitudinal direction. The bearing of the front axle must provide lateral stiffness needed for the transfer of forces to the unaffected parts of the vehicle body during an offset collision.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP78_186GB Vehicle body construction• Through the use of high quality steel, a very high firmness of the body was achieved, mainly inside the vehicle, through which the passive safety of the occupants was significantly increased. • The robust design of the sills and columns results in a high degree of firmness and rigidity. • The sills of the front doors, located at the foot of the B-pillar, are reinforced for improved rigidity. • The progressively deformable front and rear part of the vehicle ensure an optimal course of deformation of the body so that energy is absorbed most efficiently. • The design of the front doors with three lateral struttings and the rear doors with one strutting has increased rigidity and can absorb a large amount of energy in case of a side impact.SP78_19High quality steel, which can be divided into several groups in accordance with the limit values of its Protected by copyright. Copying for or commercial purposes, in part or in whole, is not Yeti permitted deformation, was used toprivate a great extent for the body of the model.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Percentage of the used sheet metals7% 21% 45% 27%Firmness of the used sheet metals Rp0.2 180 MPa Rp0.2 190-260 MPa Rp0.2 300-500 MPa Rp0.2 500 MPaSP78_20Rp0.2 - yield strengthGB7 Seat beltsAll Škoda vehicles offered on the european market are currently fitted with 3-point retractable seat belts. The belt retractor can be blocked if: • the belt is pulled out too quickly (forcefully), • when accelerating, • when changing the angular position of the spool (the belt retractor blocks when the pendulum is deflected) The seat belts in Škoda vehicles can be divided into two basic groups: with belt tensioner and without tensioning system.Seat belts with belt tensionersAlthough the fastened seat belt adheres flat to the body of the occupant, a violent forward motion of the body occurs during an accident, for example in the event of a frontal crash. This motion of the body is permitted in response to:Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability • the free play of the rolled-up seat belt, with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� • the free play resulting from the occupant's clothing.The belt tensioner regulates the tension (play) and thus the seat belt path is shortened. The belt tensioners are activated during a crash (the time delays vary depending on the type of collision). Therefore the seat belt rolls up whilst the aforementioned tension (play) is limited. Škoda vehicles are equipped with pyrotechnic belt tensioners. The ignition of the propellant charge is triggered by a signal of the airbag control unit .SP78_348GB The pyrocartridge (propellant charge) is triggered by the signal of the airbag control unit, whereby the developing gases set in motion a system of tiny balls which in turn rotates the toothed gear. The seat belt winds on the belt winding drum which is driven by the movement of the toothed gear.SP78_37SP78_38Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Three-point seat belt on the middle rear seatThe models ŠkodaRoomster and ŠkodaYeti are fitted with the VarioFlex rear seating system whereby the three-point seat belt on the middle rear seat is attached to the roof section of the body, two other attachment points are released by means of two safety catches and locks. The locks of the seat belts on the three VarioFlex rear seats are directly attached to the frame of the seats.SP78_101GB9 Seat beltsTiming of the crash at 50km/h with the passenger seated in the rear seat WEARING A SEAT BELT. The use of the seat belts is underestimated in particular by the rear seat occupants of the vehicle.Contact with an obstacle.SP78_22Activation of the belt tensioner and the airbag.SP78_23The airbag is filled, the belt force limiter begins to loosen the belt.SP78_24Contact with the airbag.SP78_25Sinking deeply into the airbag, the rearward movement begins.SP78_26Contact with the head restraint.SP78_27Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�10GB Timing of the crash at 50km/h with the passenger seated in the rear seat NOT WEARING A SEAT BELT. During a crash, the person seated in the rear seat who is not properly restrained endangers him/herself and also the driver of the vehicle, who is restrained.Contact with an obstacle - activation of the belt tensioner and the airbag.SP78_28Contact with the airbag.SP78_29Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Sinking deeply into the airbag, the passenger hits his/her knees against the backrest.SP78_30The chest and the head of the passenger make contact with the backrest.SP78_31Maximum impact.SP78_32Rearward movement.SP78_33GB11 Seat beltsBelt force limiterIn order that the force in the belt does not exceed a certain stress value when restraining the passenger's body, which could result in pelvic and thoracic injuries, the belt is fitted with a force limiter which decreases the tension of the belt when the specified values are exceeded.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Design of the locksStrong emphasis is put on the operational reliability of the seat belt lock in order to prevent the random release of the catch. The lock must also open in the event that the weight of the occupant's body exerts force on the seat belt. This feature is ensured by the use of a counterweight that prevents the lock from blocking.SP78_39SP78_4012GB AirbagsHistory of the airbagThe airbag was invented in 1952 and it was first fitted in series twenty years later. In the early history of the airbag, it was considered an alternative to seat belts. During the 1980's the airbag has been increasingly regarded not as a substitute for seat belts, but as an additional protection, creating a functional system together with the seat belts which offers greater protection than the sole use of the seat belts.air bag gas generator Driver's front airbag Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedSP78_21unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB13 AirbagsAirbag systemThe airbag system consists of the following elements: • airbags • shock sensors • central airbag control unit • electrical installation • on-off switch of the front passenger front airbag • belt tensionerfront passenger front airbag can be switched offhead airbagsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�driver's knee airbagside airbagsdriver's front airbagSP78_4214GB The airbag control unit receives signals from the acceleration sensors, the pressure sensors and the CISS sensor; in the event that the sensors communicate information that a crash has occured, the control unit transmits an activation signal to the respective group of airbags and belt tensioners. The airbag system is thus firmly connected to the belt tensioners.driver's front airbag ledges of the head airbags central airbag control unit front passenger front airbag belt tensioner of the rear seatKnee airbagpressure sensor of the front doorbelt tensioner of the driver's seat beltThe seat belt winder of the middle rear Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted isguarantee not fitted with aliability belt tensioner. unless authorised by ŠKODA AUTO A. S. does not or accept any acceleration sensor in the lower part ofŠKODA AUTO A. S. seat with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� the C-pillarSP78_41GB15 AirbagsAirbag deployment system in the ŠkodaYeti modelThe airbag deployment system consists of the central airbag control unit and four external sensors for the detection of a lateral crash. The CISS sensor is used for the first time in the Yeti model.Airbag control unitThe airbag control unit with three integrated crash sensors is located on the middle tunnel inside the vehicle. Two sensors operate according to the principle of negative vehicle acceleration (acceleration sensors), one for detecting a frontal collision, the other one for detecting a side crash. The third and newly employed sensor, the so-called CISS sensor (Crash Impact Sound Sensing), is used as an additional sensor for the detection of a frontal collision. It operates according to the principle of measuring the acoustic value of the impact force.External crash sensorsTwo types of crash sensors are connected to the airbag control unit. These are pressure and acceleration sensors which transmit unprocessed data to the airbag control unit. Pressure sensors, which are housed in the "dry" area of the driver and front passenger door, are used for detecting a side crash. An additional acceleration sensor which is located in the lower part of the C-pillar and detects a side crash which does not deform the front doors, must be used in order to detect a crash on vehicles with rear side airbags, respectively head airbags.CISS sensorAirbag systemby copyright. Copying for private or deployed commercial purposes, in part or in whole, is not permitted The CISS sensor uses the sound waves whichProtected spread The airbags are depending on the unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability out in the solid structure of the chassis and the body delay, theofangle and the side on which the crash with respect to the correctness information in this document. Copyright by ŠKODA AUTO A. S.� when the vehicle is deformed during a crash. Based occured. on the characteristics of the measured signal, the algorithm of the control unit can determine the type of crash and can trigger the impulse which deploys the airbags and the seat belt tensioners. The CISS sensor replaces one acceleration sensor in the airbag control unit (for example on the Superb ll model, the signal of three acceleration sensors, two of which are integrated in the airbag control unit, is required in order to deploy an airbag during a frontal collision). This means that an acceleration sensor, which detects the collision strength and the vehicle deceleration as well as the CISS sensor, which detects the acoustic waves, are used for the detection of a frontal crash. In order to deploy the airbags, the acceleration signal as well as the sound signal must be measured. The sensor can detect acoustic vibrations in the range of 400 Hz - 16 kHz. When using the CISS sensor it is not necessary to use an additional acceleration sensor at the front end, as is the case on the Superb ll model.16GB Use of airbags in currently produced Škoda vehiclesFabia driver's front airbag front passenger front airbag driver's and front passenger side airbag rear side airbag head airbags driver's knee airbagRoomsterOctavia TourOctaviaSuperbYetiNote: The table provides an overview of the airbags, which can be used in the different models. The composition of the airbag is dependent on the equipment of the vehicle and may vary in each country.GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�17 AirbagsGas generatorsGas generator for airbag with pyrotechnical initiator Function description: After the deployment of the airbag by the control unit, the pyrotechnical charge is ignited. This develops a small amount of gas which deforms the inner cover of the generator and penetrates the area with the chemical filling through the openings in the body of the generator as well as through the gap, which arises between the inner filling and the outer trim panel. This is where, at increased pressure and temperature, the chemical reaction with the filling takes place and more gases are produced. Then the gas stream enters the metal fibre filter, which also serves to collect the solid particles formed during the chemical reaction, and flows into the cooler where it is cooled. The gas passing through the filter then flows into the nylon bag of the airbag.outer trim panel inner trim panelProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�filter and cooler for gas expansion pyrotechnical initiatorchemical fillingSP78_43Usage: Driver's front airbag and side airbags.18GB Hybrid gas generator for airbag Function description: When the airbag is deployed the airbag initiator ignites the solid fuel which, when burning, generates inert gas in the combustion chamber. After the pressure has increased the bursting disc is perforated by the hollow sliding piston, whilst the compressed gas begins to penetrate the combustion chamber. Here it is heated, its volume increases and it fills the air bag of the airbag.combustion chamber with chemical filling bursting discProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�pyrotechnical initiator hollow sliding pistonaccumulation chamber with compressed gasSP78_44Usage: Front passenger front airbags, knee airbags, head airbags, with the exception of the ŠkodaYeti model.Gas generator On the ŠkodaYeti model the head airbag is fitted with a gas generator which, in comparison to the hybrid system, has only one chamber filled with compressed gas (helium + argon) that expands in the bag of the airbag when the control unit transmits an activation signal.SP78_101GB19 AirbagsDriver airbagThe driver airbag is installed in the centre part of the steering wheel. When the airbag inflates, the air bag fills with gas until it pierces the weak points of the plastic trim panel as programmed and fully expands in the space in front of the steering wheel. The nylon bag is also provided with an opening through which the gas automatically escapes after the bag has been inflated.plastic capSP78_46air baggenerator coverby ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability unless authorisedwith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedSP78_47generatorcontainermechanism of the hornSP78_45SP78_4820GB Front passenger airbagThe front passenger airbag is mounted in the dash panel insert above the storage compartment. When the airbag inflates, it pierces through the weak points of the plastic trim panel as programmed and comes to rest against the windscreen, thereby unfolding in front of the front passenger. In terms of volume, it is the largest airbag in the vehicle. The bag of the front passenger airbag is also provided with an opening, just as the bag of the driver's airbag, through which the gas escapes after it has inflated.SP78_49SP78_52SP78_50Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP78_53SP78_51GB21 AirbagsSide airbagThe front side airbags are located inside the outer facing part of the support of the front seat, unlike the rear seats, where they are incorporated in the side upholstery fastened to the trim panel of the C-pillar. Currently, side airbags can only be incorporated in rear seats on model ranges ŠkodaYeti and ŠkodaSuperb. All side airbags are provided again with an opening in the nylon bag, through which the gas can escape after the airbag has inflated.nylon bag of side airbag on front seat of front passengerdirected escape of gas from the opening in the bagSP78_54cartridge of front side airbagSP78_57Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�22GB Head airbagHead airbags fitted in the model ŠkodaRoomstergas generator cartridge ledge of the side airbagSP78_58SP78_59connector for the connection to the airbag control unitSP78_60Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The head airbag is common for the front and rear seat. The bag of the head airbag is not emptied in contrast to the front and side airbags. To prevent the escape of gas from the bag of the airbag, the inside of the head airbag is coated with a silicon layer.GB23 AirbagsKnee airbagcartridge of knee airbag for the model ŠkodaYetiSP78_63knee airbag in the model ŠkodaSuperbSP78_62knee airbagThe knee airbag is located under the dash panel insert. In the event of a crash it prevents the contact of the lower limbs with the parts of the dash panel insert and the rigid structures under the dash panel insert, such as the ignition key, the steering column, etc. The knee airbag is designed to prevent a person's body from slipping beneath the dash panel Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability insert. In this way, it ensures the effective operawith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� tion of the other locking systems. The contact area of the knee with the bag of the airbag is minimal and the strength of the airbag, which expands upward along the dash panel insert must not be large, so that the bag is not emptied in contrast to the front and side airbags. It is therefore significantly firmer. To prevent the escape of gas from the bag of the airbag, the inside of the knee airbag is coated with a silicon layer, as in the case of the head airbag. The knee airbag is part of the standard equipment in the model range ŠkodaSuperb and it can also be fitted to the model ŠkodaYeti.simulation of frontal impactSP78_7824GB Interruption of current conductorSP78_87On the ŠkodaSuperb model with 3.6 ltr. FSI petrol engine, the vehicle battery is located in the luggage compartment. The main current conductor is guided along the length of the entire vehicle into the engine compartment; in case of an accident a short circuit of this conductor may arise, for this reason the current conductor path is interrupted as a result of the ignition of a pyrotechnic charge connected to the airbag control unit when the airbag is deployed. The low-current systems remain energized.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP78_88GB25 SeatsSafety function of the seatsThroughout the journey, the occupants remain seated, therefore it is necessary that the seats meet the high demands on safety.The softer middle parts of the seat and the support allow the body of the driver to sink slightly into the seat, while the firm, specially shaped edges of the seat secure the position of the occupant. The seat is designed to prevent the occupant's body from sliding under the seat belt and beneath the bottom part of the dash panel insert during a frontal collision.SP78_69Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP78_7026GB SupportsSP78_71What is a cervical vertebrae syndrome (whiplash syndrome)?It is a seemingly inconspicuous injury that occurs in approximately half of all traffic accidents. It occurs most often in vehicle collisions as a result of a frontal impact or when crashing into the back of another vehicle. Both the driver and the passengers are exposed to this type of injury. This type of injury results from the violent movement of the head due to the external shock during a collision of the vehicle. The head and neck are suddenly jerked either backwards or forwards, immediately followed by the head being forcefully thrown backwards. In principle, this backward movement resembles the lash of a whip, hence the term "whiplash". During a whiplash injury, the head usually snaps back and the rear part of the head hits against the Protected copyright. Copying for adjusted. private or commercial purposes, in part or in whole, is not permitted head restraint, which isbyoften wrongly unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Computer-based analysis of the load on the cervical vertebraeSP78_72GB27 SeatsSupportsFor example, the model ŠkodaYeti is equipped with the head restraint WOKS II . This head support together with the seat achieved an excellent result in the rear-end crash tests EURO NCAP. It beat all competitors, including active head restraint systems. This is the result of the perfect interaction with the ergonomics of the seat and the head support. It is based on the shortest possible distance between the head support and the head. The whiplash syndrome is influenced, to a large extent, by the occupants themselves. If the head support is not adjusted to the optimum height, its function is severly affected. The most important factor for the proper functioning of the head restraint is its correct adjustment. In the past it was recommended that the top of the head restraint should be at eye level, nowadays however the top of the head restraint must be level with the top of the head, thus approx. 7 cm higher. During a frontal or a rear crash, the belted occupant is thrown back higher into the seat (trajectory) than it was the case during the forward movement, due to the seat belt extending and the movement of the vehicle body. This is particulary visible in the slow-motion pictures of the crash tests where the head of the dummy can be seen hitting against the upper edge of the head support. The head restraint should not be a hindrance to the free movement of the head while driving, however a minimum distance should be kept between the head and the head support.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�head restraint is set too lowSP78_7328GB Use of the child seatThe use of the child seat is the basic prerequisite for the safe transportation of the child in the vehicle. All model ranges of Škoda Auto are already offered in the basic version with the standard ISOFIX system for attaching the child seat.ISOFIX systemISOFIX is an international designation for a uniform child seat attachment system in the vehicle. The outer rear seats of vehicles which are currently produced by Škoda Auto are provided with fixing eyes, used for attaching the child seat in the vehicle. The fixing eyes are anchored to the frame of the rear seats (Roomster, Yeti) or directly to the body beneath the seats (Octavia, Fabia, Superb). The system considerably limits the possibility of a bad installation, it is sufficient to insert the child seat into two catches between the seat and the support. On the model ranges ŠkodaOctavia, ŠkodaSuperb and the model ŠkodaYeti, the front seat of the front passenger can also be fitted with the ISOFIX system.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�child seat attached to the front seat of the front passenger with the ISOFIX system on the model ŠkodaOctavia SP78_91GB29 Steering columnVehicles produced by Škoda Auto feature a steering column designed as a sliding steering column. During a frontal crash with deployment of the airbag and the driver's body hitting the steering wheel above the airbag (see fig. SP78_79), the steering column is pushed in by about 75 mm, thereby reducing the possibility of injury from the steering wheel. Enlarging the space for the driver enables the locking systems to slow down the body on its flight path.SP78_74mm for private or commercial purposes, in part or in whole, is not permitted Protected by copyright. Copying unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�75SP78_7630GB Timings of the airbag deployment and the steering rod sliding inStatus of the locking systems prior to the deployment.SP78_77Status of the locking system prior to the dummy striking the airbags.SP78_78Maximum forward movement of the dummy.SP78_79Status of the locking systems and the dummies after the test - the steering wheel is moved by 75 mm in direction of the engine.SP78_80Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB31 PedalsSP78_64The pedal system in vehicles produced by Škoda Auto is supplemented with wire reinforcements which prevent the pedals from migrating into the interior of the vehicle during a frontal crash. The module carrier, on which the wire reinforcements are attached, does not deform during a crash; provided that the attachment of the pedals is displaced forwardly in the vehicle, the wire reinforcements move the pedals into their extreme position that corresponds to the position when the pedals are depressed, so that the feet of the driver are not injured.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP78_65SP78_6632GB Glass fillingsDuring an impact, ordinary glass shatters into large pieces with sharp edges. Large pieces of glass could easily endanger people. Therefore, special safety glass is used in the automotive industry. Side windows - tempered glass In most cases, tempered glass is used for the side windows of the vehicles which is much stronger and can withstand greater impacts than ordinary glass. During the manufacturing process, the window panes are heated to a temperature near the melting point of the glass (approx. 650 °C) whereby subsequently they are cooled down evenly and quickly with a cold stream of air. In this way, an inner tension is created in the surface layer of the material, which ensures its strength while making it five times stronger after tempering than ordinary glass. Tempered glass shatters into tiny pieces with blunt edges. Windscreen - laminated glass Laminated glass is used for the windscreens of vehicles, which consists of two layers of glass bonded with a foil made of polyvinyl butyral (PVB). This foil is colorless, transparent, UV-opaque and ensures a higher strength of the windscreen. If the window filling is destroyed, the PVB interlayer acts as a bonding agent on which sticks most of the shattered glass, eliminating possible injuries to the occupants. The windscreen also goes through a thermal tempering process, so that it shatters into small pieces with blunt edges just as the side windows.SP78_83Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP78_85PVB-FolieGB33 Exterior safetyThe protection of pedestrians is a priority for Škoda vehicles. The exterior safety includes the following elements: • rounded corners on the body • resilient bumpers • deformation properties of the body • shape of exterior door handles • adjustable mirrors • shape of window wipers • hub caps • shape of the front part of the vehicleFront bumperTo increase the safety of a pedestrian in case of a collision with the vehicle, the front bumper of Škoda vehicles is provided with a reinforcement and a foam filling.steel reinforcementfoam fillingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�reinforcement of the front bumperfront bumperSP78_99Foam filling The foam filling is made from polypropylene and is located under the middle part of the bumper on a steel cross member of the bumper. It serves to absorb the energy released by an impact at low speeds (max. 40km/h) and to prevent serious injuries to pedestrians.Reinforcement of the front bumper The reinforcement is made of plastic and is located in the lower part of the bumper, where its overall rigidity is increased. In the event of a possible collision of a pedestrian with a vehicle, the pedestrian is thrown onto the engine hood of the vehicle due to the reinforcement of the bumper, whereby the pedestrian is not caught under the wheels of the vehicle, which could lead to more serious injuries.34GB Euro NCAPEuro-NCAP (European New Car Assessment Program) is an independent consumer test for establishing the safety of automobiles. The test was introduced in 1997 by the automobile clubs and societies for the consumer protection. This institution was established in order to have comparable results of crash tests available within Europe. In the tests that are carried out on vehicles, the safety of pedestrians and vehicle occupants is evaluated separately. Part of the test consists of: – testing the safety of the pedestrians – testing the safety of the occupants • frontal offset crash • side crash • crashing into a pole. Since 2009, the rear-end crash test - whiplash is also part of the test. The overall result of the Euro-NCAP test is indicated by the number of yellow stars. The maximum is five stars. In 2009, the ŠkodaYeti model was awarded the maximum number of stars. In addition to the protection of adult occupants, the level of protection of children in the vehicle as well as the protection of pedestrians play a large part in the overall assessment of the ŠkodaYeti model.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP103_99GB35 Overview of the previously edited self-study programmesNo. Designation1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50No. DesignationMono-Motronic 51 2.0 ltr./85 kW petrol engine with balancing shafts Central locking and two-stage intake manifold Vehicle alarm 52 ŠkodaFabia; 1.4 ltr. TDI engine with unit injection Working with wiring diagrams system ŠKODA FELICIA 53 ŠkodaOctavia; Vehicle presentation Safety of the ŠKODA vehicles 54 ŠkodaOctavia; Electrical Components Principles of ABS - were not published 55 FSI petrol engines; 2.0 ltr./110 kW and 1.6 ltr./85 kW ABS - FELICIA 56 Automatic gearbox DSG-02E System for safe start-up with transponder 57 Diesel engine; 2.0 ltr./103 kW TDI with pump-nozzle Air conditioning in the vehicle units, 2.0 ltr./100 kW TDI with pump-nozzle units Air conditioning FELICIA 58 ŠkodaOctavia, Chassis and electromechanical 1.6 engine - MPI 1AV power-assisted steering Four-cylinder diesel engine 59 ŠkodaOctavia RS, 2.0 ltr./147 kW FSI turbo engine Power-assisted steering 60 2.0 ltr./103 kW 2V TDI diesel engine; particle filter ŠKODA OCTAVIA with additive 1.9 ltr. TDI diesel engine 61 Radio navigation systems in the Škoda ŠKODA OCTAVIA Convenience electronic system 62 ŠkodaRoomster; Vehicle presentation part l ŠKODA OCTAVIA Manual gearbox 02K, 02J 63 ŠkodaRoomster; Vehicle presentation part ll 1.6 ltr. and 1.8 ltr. petrol engines 64 ŠkodaFabia II; Vehicle presentation Automatic gearbox - fundamentals 65 ŠkodaSuperb II; Vehicle presentation part l Automatic gearbox 01M 66 ŠkodaSuperb II; Vehicle presentation part ll 1.9 ltr./50 kW SDI, 1.9 ltr./81 kW TDI diesel engines 67 Diesel engine; 2.0 ltr./125 kW TDI with Common 1.8 ltr./110 kW and 1.8 ltr./92 kW petrol engines Rail injection system OCTAVIA, CAN BUS 68 1.4 ltr./92 kW TSI petrol engine with turbocharger OCTAVIA - CLIMATRONIC 69 3.6 ltr./191 kW FSI petrol engine OCTAVIA - safety of the vehicle 70 All-wheel drive with Haldex coupling of the lV. OCTAVIA - 1.4 ltr./44 kW engine and gearbox 002 generation OCTAVIA - ESP - fundamentals, design, function 71 ŠkodaYeti; Vehicle presentation part l OCTAVIA 4 x 4 - all-wheel drive 72 ŠkodaYeti; Vehicle presentation part ll 2.0 ltr. 85 kW and 88 kW petrol engines 73 LPG system in Škoda vehicles Radio navigation system - design and functions 74 1.2 ltr./77 kW TSI petrol engine with turbocharger ŠKODA FABIA - technical information 75 Automatic 7-speed gearbox with double clutch 0AM ŠKODA FABIA - electrical systems 76 Green Line vehicles ŠKODA FABIA - electro-hydraulic power-assisted 77 Geometry steering 78 Passive safety 1.4 ltr. - 16 V 55/74 kW petrol engines ŠKODA FABIA - 1.9 ltr. TDI Unit injection Manual gearbox 02T and 002 ŠkodaOctavia; model 2001 Euro-On-Board-Diagnosis Automatic gearbox 001 6-Speed gearbox 02M Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted ŠkodaFabia - ESP unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Exhaust emissions with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Extended service intervals Three-cylinder petrol engines 1.2 ltr. ŠkodaSuperb; Vehicle presentation; part l ŠkodaSuperb; Vehicle presentation; part ll ŠkodaSuperb; 2.8 ltr./142 kW V6 petrol engine ŠkodaSuperb; 2.5 ltr./114 kW TDI V6 petrol engine ŠkodaSuperb; automatic gearbox 01VOnly for the internal use in the service network ŠKODA. All rights reserved. Subject to technical modifications. S00.2002.78.20 E GB Technical status 12/2009 © ŠKODA AUTO a.s. http://portal.skoda-auto.comThis paper was made out of chlorine-free bleached cellulose.78