TECHNICAL DOCUMENTATION

SSP 083 1.4 132kW TSI petrol engine with dual charging

PDFEN48 pages2 MB
SSP 083 1.4 132kW TSI petrol engine with dual charging - PDF cover

This PDF is currently unavailable.

Read document text
Service1.4 ltr./132 kW TSI petrol enginewith dual-charging (compressor, turbocharger)83Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Self-study programme We would like to introduce you to the first engine produced in series by Škoda, which is also equipped with a compressor and a turbocharger. As of 05/2010, the model ŠkodaFabia II RS is fitted with the 1.4 ltr./132 kW TSI engine.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�2GB ContentsBrief description of the engineEngine characteristics Technical data4 4 5 6 6 6 7 8 8 9 10 11 12 13 15 17 18 18 19 20 21 23 24 25 25 26 28 38Engine mechanicsCylinder block Crank mechanism Cylinder head and valve drive Chain drive for the control system and the oil pump Inlet camshaft adjustment V-ribbed belt drive Dual-charging - compressor and turbocharger Schematic overview of the supercharging components Working ranges of the supercharging components Implementation of the working ranges Supercharger Noise insulation of the supercharger Turbocharging Exhaust manifold Charge air cooling Oil supply Two-circuit cooling system Demand-regulated fuel system Exhaust systemEngine managementCAN networking System overview Sensors ActuatorsYou will find the instructions for the assembly and disassembly, repair, diagnostics and detailed user information in the workshop manuals, the diagnostic units VAS and in the onboard literature. The time for going to press was on the 05/2010. This brochure is not subject to an update.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB3 Brief description of the engineEngine characteristicsThe fundamental structural part is the 1.4 ltr./92 kW TSI engine which, amongst other things, is installed on the Superb ll model. The main technical highlight and the difference to the 1.4 ltr./92 kW TSI engine is primarily the dualcharging. The engine is charged by the mechanical compressor and/or the exhaust turbocharger, based on need. This technical solution ensures that very high engine dynamics is achieved at relatively low fuel consumption, which is a characteristic of the TSI engines.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP83_02Technical highlights• • • • • • 4-valve technology Grey cast iron-cylinder block forged crankshaft Homogeneous charge mode (lambda = 1) Double injection catalytic converter heating Exhaust turbocharger with wastegate switchable mechanical compressor supercharging • charge air cooling • maintenance-free chain drive • engine cover with vacuum reservoir for the intake manifold switchover flap • plastic intake manifold • continuous inlet camshaft adjustment • demand-regulated fuel system • high-pressure fuel pump with a delivery pressure of up to 15 MPa (150 bar) • communication via the diagnostic transport protocol UDS4GB Technical dataEngine code Design Number of cylinders Valves per cylinder Displacement Bore Stroke Compression ratio max. power output max. torque Control unit Fuel Exhaust after treatment Emission standard CAVE Production engine 4 4 1390 cm3 76,5 mm 75.6 mm 10 : 1 132 kW at 6200 min-1 250 Nm at 2000 - 4500 rpm-1 Bosch MED 17.5.5 Super unleaded with octane number 98 or 95 - with low reduction in performance Three-way-catalytic converter; lambda control EU5Torque and power output diagram130 120 110 100 90 P (kW) 80 70 60 50 40 30375 350 325 300 275 M (Nm) 250 225 200 175 150 12510002000 3000 4000 5000 6000 7000 n (min-1)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted SP83_01 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB5 Engine mechanicsCylinder blockThe cylinder block of the 1.4 ltr./132 kW is taken over from the 1.4 ltr./92 kW TSI engine.Cylinder body Outer wall of cylinder block made out of grey cast ironSP83_03Crank mechanismThe crank mechanism of the 1.4 ltr./132 kW TSI engine is based on the drive unit of the 1.4 ltr./92 kW TSI engine just as the cylinder block.Piston Graphite coating of the piston shellPiston pinConrodProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Forged crankshaftSP83_04Further information regarding the cylinder block and the crank mechanism can be found in the self-study programme 68.6GB Cylinder head and valve driveDue to the higher loads, the valve seats of the outlet valves are reinforced with hard alloy and the valve springs are made out of stainless steel. Due to the higher exhaust gas temperatures, the valve shafts of the outlet valves are filled with sodium for better heat transfer. This reduces the temperature at the outlet valves by approx. 100 °C.Cylinder headSP83_05Outlet valveSuction valveCamshaft housing The camshafts, which are mounted on three bearings, are inserted into the camshaft housing. Their axial play is limited by the caps. The high-pressure fuel pump is bolted to the camshaft housing, which is driven by a double cam on the inlet camshaft. The stroke of the high-pressure fuel pump is 5.7 mm. The friction forces are reduced by a roller tappet between the high-pressure fuel pump and the camshaft.High-pressure fuel pump with roller tappet Camshaft housingInlet camshaftDouble cam of pump driveSP83_06Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB7 Engine mechanicsChain drive for the control system and the oil pumpThe drive of the camshafts as well as the oil pump is performed using maintenance-free toothed chains, which are driven by the crankshaft via gear wheels. The drive of the camshafts The toothed chain has hardened pins and plates with high load-bearing capacity, which have been suf ficiently adapted to the chain forces. The toothed chain is tensioned by a mechanicalhydraulic chain tensioner. Oil pump drive The oil pump is driven by a toothed chain with 8 mm pitch for improved sound. It is tensioned by a spring-loaded chain tensioner.Sprocket for inlet camshaft with vane adjusterOutlet camshaft sprocketCamshaft drive sprocketSlide railTensioning rail Drive sprockets on crankshaft for driving camshafts and oil pump Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Mechanical-hydraulic chain tensionerunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Spring-loaded chain tensioner Oil pump chain drive Oil pump sprocketSP83_07Inlet camshaft adjustmentA load- and engine speed-dependent vane adjuster is used for the continuous inlet camshaft adjustment. The adjustment range is a maximum 40° crank angle. The camshaft adjustment allows for an improved torque band and very good internal exhaust gas recirculation.8GB V-ribbed belt driveThe 1.4 ltr./132 kW TSI is fitted with two V-ribbed belts. - The ancillary components are driven by a six-groove V-ribbed belt. The belt drives the coolant pump, the alternator and the AC compressor from the crankshaft pulley. - The supercharger is driven by a five-groove V-ribbed belt. It drives the compressor when the magnetic clutch is engaged.Two tensioning pulleys ensure that the ancillary components are correctly tensioned while the supercharger belt is correctly tensioned by one tensioning pulley. The tensioning pulley (on the right of the crankshaft pulley) also ensures that the V-ribbed belt runs correctly around the crankshaft pulley and the coolant pump pulley.Supercharger drive beltAncillary components drive beltTensioning pulleySupercharger belt pulleyAlternator belt pulleyTensioning pulleyProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Tensioning pulleyCoolant pump pulley/pulley for supercharger magnetic clutch N421SP83_08Air-conditioning compressor belt pulleyCrankshaft belt pulleyGB9 Engine mechanicsDual-charging - compressor and turbochargerOn Škoda models with charged engines, the supercharging was so far carried out solely with an exhaust turbocharger. The 1.4 ltr./132 kW TSI engine is the first to use a combination of compressor and exhaust turbocharger. This means that the engine is charged by a compressor in addition to the exhaust turbocharger depending on the torque requirements.TurbochargerTurbochargerThe turbocharger is constantly driven by the exhaust gas. Advantages: - very good efficiency due to the use of exhaust gas energy Disadvantages: - in a small engine, the boost pressure produced in the lower speed ranges is not sufficient to generate a high torque - high thermal loadingSP83_09SuperchargerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The compressor is a mechanical charger which is activated by a magnetic clutch. Advantages: - faster build-up of boost pressure - a high torque at low engine speeds - only activated when required - no external lubrication and cooling necessary Disadvantages: - requires drive power from engine - boost pressure is produced depending on engine speed and is then regulated (whereby part of the generated power is lost again)SP83_10Mechanical supercharger10GB Schematic overview of the supercharging componentsRegulating flap control unit J808 Supercharger drive Intake manifold pressure sender (compressor) G583 with intake air temperature sender G520Mechanical superchargerIntake manifold pressure sender G71 with intake air temperature sender G42Intake airAir filter Intake manifold Throttle valve module J338 Charge pressure sender G31 with intake air temperature sender G299Magnetic clutchAncillary components drive beltCharge air cooler Exhaust manifold Charge pressure control solenoid valve N75 Catalytic converterCharge pressure control vacuum unit Turbocharger air recirculation valve N249 Turbocharger Bypass valve (wastegate)Exhaust gasesSP83_11The intake air flows through the air filter. The position of the regulating flap defines whether the intake air flows via the compressor or straight to the turbocharger.The air compressed by the turbocharger flows via the charge air cooler and the throttle valve module J338 into the intake manifold.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB11 Engine mechanicsWorking ranges of the supercharging componentsDepending on the torque requirement, the engine control unit determines whether and in which way the required boost pressure is generated. The turbocharger operates within the entire speed ranges. The exhaust gas energy is not sufficient in the lower speed ranges to generate the required boost pressure on its own.Constant boost range of supercharger The supercharger is constantly activated up to an engine speed of 2400 rpm. The supercharger boost pressure is controlled via the regulating flap control unit J808.Requirement-dependent boost range of supercharger Up to a maximum engine speed of 3500 rpm, the supercharger is activated when necessary (for example, this is necessary when the vehicle is driven at a constant speed in this range and then accelerates quickly). Due to the slow response of the turbocharger, this forceful acceleration would be delayed. Therefore, the supercharger is activated by the engine control unit and the required boost pressure is reached as quickly as possible.Turbocharger boost range In the green area, the turbocharger produces the required boost pressure on its own. The boost pressure is controlled by the charge pressure control solenoid valve N75.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Torque (Nm)Engine speed (rpm)SP83_1212GB Implementation of the working rangesDepending on the load and speed range, the engine control unit regulates how the intake air should reach the cylinders in order to achieve the required torque. The engine control unit determines whether the turbocharger can produce the boost pressure on its own or whether the compressor must be activated.Naturally aspirated mode at low load The regulating flap of the compressor is fully open in the naturally aspirated mode. The intake air flows via the open regulating flap to the turbocharger. The turbocharger is driven by the exhaust gas, however the exhaust gas energy is so low that it only produces a small boost pressure. The throttle valve position corresponds to the position of the accelerator pedal and there is a vacuum in the intake manifold.Regulating flap control unit J808Throttle valve module J338Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�TurbochargerSP83_13Supercharger and turbocharger operation at high loads and engine speeds up to 2400 rpm In this speed range, the regulating flap is closed. The supercharger is activated via a magnetic clutch and compresses the intake air. The compressed air is now led to the turbocharger where it is compressed even more. The boost pressure of the supercharger is measured by the intake manifold pressure sender G583 and is regulated by the regulating flap control unit. The overall boost pressure is measured by the charge air pressure sender G31. The throttle valve is fully open. A pressure of up to 0.25 MPa (2.5 bar) is built up in the intake manifold.Supercharger Intake manifold pressure sender (compressor) G583 Regulating flap control unit J808Throttle valve module J338 Charge pressure sender G31Magnetic clutchTurbochargerSP83_14GB13 Engine mechanicsTurbocharger and supercharger operation at high loads and engine speeds in the range of 2400 up to 3500 rpm In this speed range, the boost pressure is produced at a constant speed by the turbocharger alone. When the vehicle is driven at a constant speed and then accelerates quickly, the turbocharger would be too slow to generate the required boost pressure fast enough. For this reason, the engine control unit activates the supercharger and adjusts the regulating flap control unit J808 according to the required boost pressure. Thus, the supercharger supports the turbocharger in generating the necessary boost pressure.Supercharger Regulating flap control unit J808Throttle valve module J338Magnetic clutchTurbochargerSP83_15Turbocharger operation As of an engine speed of approx. 3500 rpm, the turbocharger can produce the required boost pressure on its own at any load point. The regulating flap is fully open and the intake air flows straight to the turbocharger. The exhaust gas energy is suf ficient to produce the required boost pressure. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability A pressure of up to 0.2 MPa (2 bar) is built up with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� in the intake manifold. The boost pressure of the turbocharger is measured by the charge air pressure sender G31 and is regulated by the charge pressure control solenoid valve N75.Supercharger Regulating flap control unit J808Throttle valve module J338 Charge pressure sender G31Magnetic clutch TurbochargerSP83_16Charge pressure control solenoid valve N7514GB SuperchargerSupercharger drive The supercharger is activated as required with a magnetic clutch located on the coolant pump module. The supercharger is driven by the coolant pump via a belt drive. Due to the gear ratio of the crankshaft belt pulley to the supercharger belt pulley, the supercharger turns at five times the crankshaft speed. The maximum speed of the supercharger is 17500 rpm.Pulley for supercharger magnetic clutch Supercharger drive belt Coolant pump pulleySupercharger Compressor belt pulley Tensioning pulleySP83_17Crankshaft belt pulleyProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The supercharger may not be opened. The chamber containing the speed step gears is filled with life-time oil.SP83_18RotorsSpeed step gearsMechanical supercharger The mechanical supercharger is bolted to the cylinder block on the intake manifold side after the air filter. Two screw rotors compress the intake air. The boost pressure is controlled via the regulating flap control unit J808. The maximum boost pressure generated by the supercharger is approx. 0.175 MPa (1.75 bar).RotorsSP83_19Delivery sideSuction sideGB15 Engine mechanicsSupercharger function The two supercharger rotors have been designed so that, when they rotate, the space on the intake side becomes larger. The intake air is supplied to the pressure side of the supercharger by the rotors. On the pressure side, the space between the two supercharger rotors becomes smaller again. The intake air is compressed and led to the turbocharger.Delivery side Rotors Suction side Mechanical superchargerFrom air filter Regulating flap control unit J808 To turbochargerSP83_20Supercharger boost pressure regulation The boost pressure is regulated by the position Delivery side Suction side of the regulating flap. When the regulating flap is closed, the supercharger produces a maximum boost pressure. All of the compressed air is led to the turbocharger. If the boost pressure is too high, the regulating flap is opened partially. Now part of the intake air is fed directly to the turbocharger and the rest is led back via the partly opened regulating flap Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted to the intake side of the supercharger. Thus, unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the is correctness of information this is document. Copyright by ŠKODA AUTO A. S.� the boost pressure reduced. The in air drawn in again on the intake side of the supercharger and compressed once more. From air filter This reduces the drive power of the supercharger (conservation of energy). Regulating flap The boost pressure is measured by the intake control unit J808 SP83_21 manifold pressure sender (compressor) G583. To turbocharger Intake manifold pressure sender (compressor) G583 with intake air temperature sender G52016GB Noise insulation of the superchargerDue to the arrangement of the supercharger in the direction of the passenger compartment, the noises resulting from its operation can be heard by the occupants. Several measures have been taken to reduce the noise level: Design features: - the geometry of the gearing has been modified (meshing angle and twisting play) - the supercharger shafts have been stiffened - the supercharger case has been reinforced with special ribs - both sides (fill and discharge side) of the supercharger have been sound-proofed - the supercharger has been encapsulated in plastic and the housing parts are also lined with insulating foam for sound proofingSound-proofing on the fill sidePlastic housing of the superchargerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Insulating with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�foamInsulating foamSound-proofing on the discharge sidePlastic housing of the supercharger Mechanical superchargerSP83_22Supercharger drive beltSupercharger During fast acceleration, the supercharger can “whine” at speed ranges between 2000 - 3000 rpm. However, this is the normal operating noise of a supercharger.Magnetic clutch When the magnetic clutch is switched off, three leaf springs pull the friction plate of the compressor belt pulley back to the starting position. In this case, a normal "clicking" of the magnetic clutch can be heard. This can also occur up to an engine speed of 3400 rpm.GB17 Engine mechanicsTurbochargingThe turbocharger forms a module with the exhaust manifold. The turbocharger module is made from highly heat-resistant cast steel due to the exhaust gas temperatures. The turbocharger has been incorporated in the cooling circuit to protect the shaft bearings from high temperatures. The circulating pump V50 ensures the circulation of the coolant in the cooling circuit after the engine has been switched off (up to 15 minutes). This prevents the urbocharger from overheating and steam bubbles forming in the cooling circuit. The shaft bearings are connected to the oil circuit of the engine to ensure lubrication and to improve the cooling. Furthermore, the electrical turbocharger air recirculation valve N249 and a charge pressure control vacuum unit with the waste gate are located on the turbocharger module.Turbocharger air recirculation valve N249 Turbocharger module Oil connectionSP83_23Charge pressure control vacuum unitBypass valve (wastegate)Coolant connectionExhaust manifoldThe exhaust manifold of the 1.4 ltr/132 kW TSI engine is designed for exhaust gas temperatures up to 1050 °C. Therefore, the engine can be run with a high boost pressure and with Lambda 1 in almost all map ranges.TurbochargerExhaust manifoldSP83_24Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�18GB Charge air coolingThe 1.4 ltr./132 kW engine uses a charge air cooler. The compressed and thus the heated charge air flows via the aluminium fins of the cooler where it releases a large part of its heat energy. The aluminium fins are cooled by the flow of the ambient air. The cooled charge air flows to the throttle valve and then into the intake manifold module.Regulating flap control unit J808TurbochargerHeated charge air of turbochargerAir-cooled charge air cooler Throttle valve module J338Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�from the supercharger or from the regulating flap of the superchargerCooled charge air to throttle valveSP83_25After the intake air has passed the turbocharger, it is very hot. The charge air is heated up to 200 °C mainly by the compression process, but also by the high temperature of the exhaust gases. As a result, the charge air has a low density and less oxygen will reach the cylinders. Cooling the charge air will increase its density and more oxygen is fed to the cylinders. Furthermore, the knocking tendency and the production of nitrogen oxides are reduced.GB19 Engine mechanicsOil supplyOil circuitOil filter TurbochargerThe turbocharger and the piston cooling nozzles are integrated in the oil circuit of the 1.4 ltr./132 kW TSI engine.Legend: Oil suction Oil feed Oil returnPiston cooling nozzlesOil pumpSP83_26Duo-centric oil pump The duo-centric oil pump is located under the cylinder block and is driven by the crankshaft via a maintenance-free toothed chain drive. The chain is optimally tensioned by a mechanical spring-loaded chain tensioner.Drive chain sprocket on the crankshaft for the oil pump driveSpring-loaded chain tensionerToothed chainSP83_27Oil pump sprocketProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�20GB Two-circuit cooling systemThe 1.4 ltr./132 kW TSI engine uses a dual-circuit cooling system with different temperatures and with a separate coolant flow due to the cylinder block and cylinder head. In the cylinder head, the coolant passes from the suction side (inlet side) to the outlet side. An even temperature level is thus reached in the cylinder head. This method is called crossflow cooling.Technical highlights: - two-circuit cooling system for various coolant temperatures in the cylinder head and the cylinder block (two thermostats) - thermostat 1 for the cylinder head is a twostage type - electrical pump for coolant circulation V50 - cooling of the turbocharger13 12Legend: 1 throttle 2 heat exchange for heating system 3 thermostat 1 for cylinder head (opens at 80 °C) 4 coolant distributor housing 5 thermostat 2 for cylinder block (opens at 95 °C) 6 radiator 7 oil cooler 8 electrical pump for coolant circulation V50 9 turbocharger 10 cylinder head coolant circuit 11 cylinder block coolant circuit 12 coolant pump 13 expansion reservoir12 3 11 10 9 7 1 8 6SP83_284 5Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB21 Engine mechanicsThe cooling system of the 1.4 ltr./132 kW TSI engine is divided into two circuits. Approximately one third of the coolant circulates in the cylinder block and two thirds flow to the combustion chambers in the cylinder head. The two-circuit cooling system has the following advantages: - The cylinder block warms up faster because the coolant remains in the cylinder block until it reaches 95 °C (the fast heating up of the cylinder walls reduces the emissions of hydrocarbons). - The higher temperature level in the cylinder block leads to less friction in the crankshaft drive. - The lower temperature level (80 °C) in the cylinder head allows a better cooling of the combustion chambers. This achieves better filling with a lower knocking tendency.Cylinder head cooling circuitThermostat 2Thermostat 1Cylinder block cooling circuitSP83_29Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Coolant distributor housing with twostage thermostat 1 for the cylinder headDue to the relatively high coolant delivery quantity, high pressure occurs in the cooling system at high engine speeds. The two-stage thermostat 1 for the cylinder head also opens in these conditions, based on the exact need. If a single-stage thermostat was used, a large thermostat plate would have to be opened against the high pressure. Due to the counteracting forces, the thermostat would only open at high temperatures. The two-stage thermostat only opens a small thermostat plate at first when the desired coolant temperature is reached. The counteracting forces are lower due to the smaller surface of the small plate and the thermostat opens at the exact temperature. After a specific path, the small thermostat plate moves a larger plate and the maximum possible cross-section is opened.Thermostat plate stage 1Thermostat plate stage 2SP83_30Stage 1 Stage 222GB Demand-regulated fuel systemThe fuel system of the 1.4 ltr./132 kW TSI engine has been taken from the 1.4 ltr./92 kW TSI engine. The electrical fuel pump as well as the high-pressure fuel pump always deliver the amount of fuel required by the engine at that moment. This reduces the electrical and mechanical drive power of the fuel pumps and fuel is saved.Low-pressure fuel system Door contact switch for fuel pump supply G6High-pressure fuel system Onboard supply control unit (BCM) J519; voltage supply for fuel pump supply G6Engine control unit J623Fuel pressure sender G247Pressure limiting valve (opens at a pressure of 17 MPa) Fuel pump control unit J538RailFuel filter with pressure regulator valveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Fuel pressure regulator valve N276High-pressure fuel pump Injectors for cylinder 1-4 N30-N33Electric fuel pump G6 0.05 - 0.64 MPa (0.5 - 6.4 bar)5 - 15 MPa (50 - 150 bar)SP83_31GB23 Engine mechanicsExhaust systemThe exhaust gases are treated by a three-way catalytic converter. The connecting pipe between the turbocharger and the catalytic converter has thermal insulation which ensures a quick warm-up of the catalytic converter and at the same time serves as a heat protection for the surrounding components. A linear lambda probe is mounted in the inlet funnel of the catalytic converter. Due to its position, it is exposed evenly to the exhaust gas from all cylinders. A fast start of the lambda control is reached because it is located near the engine.Connecting pipe with thermal insulationRear silencer Three-way-catalytic converterPre-silencerFlexible decoupling element Linear lambda probe in front of catalytic converter G39/ lambda probe heater in front of catalytic converter Z19SP83_32Step-type lambda probe after catalytic converter G130/ lambda probe heater after catalytic converter Z29Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�24GB Engine managementCAN networkingThe diagram below shows the control units with which the engine control unit J623 communicates via the CAN data bus.G419T16J623J745J104J743J500J587J533 J519J234 J362 J285 E221G85J527 J255SP83_42E221 G85 G419 J104 J234 J255 J285 J362 J500 J519 J527 J533Operating unit in steering wheel J587 Selector lever sensors control unit of the Steering angle sender automatic gearbox Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted ESP sensor unit J623 Engine control unit unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability respect unit to the correctness of information in this document. Copyright by ŠKODA AUTO A. S. � double clutch gearbox ABS/ESPwith control J743 Mechatronics for Airbag control unit J745 Cornering light and headlight range control Climatronic control unit unit Control unit with display in dash panel insert T16 Diagnosis connector Immobiliser control unit Power steering control unit CAN data bus drive train Onboard supply control unit (BCM) CAN data bus - Convenience Steering column electronics control unit Data bus LIN Data bus diagnostic interface (GATEWAY)GB25 Engine managementSystem overviewSensorsIntake manifold pressure sender G71 with intake air temperature sender G42 Intake manifold pressure sender (compressor) G583 with intake air temperature sender G520 Charge pressure sender G31 with intake air temperature sender G299 Engine speed sender G28 Hall sender G40 Throttle valve module J338 with throttle valve drive angle sender 1 G187 and throttle valve drive angle sender 2 G188 Regulating flap control unit J808 with regulating flap potentiometer G584 Accelerator position sender G79 and accelerator position sender 2 G185 Brake pedal position sender G100 Fuel pressure sender - high pressure G247 Knock sensor 1 G61 Coolant temperature sender G62 Radiator outlet coolant temperature sender G83CAN data bus drive train Onboard supply control unit (BCM) J519/ data bus diagnostic interface (GATEWAY)GBDiagnosis connectorLambda probe G39 Lambda probe after catalytic converter G130 Brake servo pressure sensor G294 Additional input signalsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�26 ActuatorsFuel pump control unit J538/fuel pump G6 Engine control unit J623 with ambient pressure senderInjection valves N30, N31, N32, N33 Ignition coils 1 - 4 with output stages N70, N127, N291, N292Throttle valve module J338 with throttle valve drive G186 Regulating flap control unit J808 with regulating flap position control motor V380Motronic current supply relay J271Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Fuel pressure regulator valve N276 Activated charcoal filter system solenoid valve N80 Magnetic clutch for supercharger N421Control unit with display in dash panel insert J285Lambda probe heater Z19 Lambda probe heater after catalytic converter Z29 Camshaft adjustment valve 1 N205Turbocharger air recirculation valve N249Electric power control fault lamp K132 Exhaust gas warning lamp K83Charge pressure control solenoid valve N75 Additional coolant pump relay J496/coolant circulation pump V50 Additional output signalsSP83_43GB27 Engine managementSensorsIntake manifold pressure sender G71 with intake air temperature sender G42This combined sender, which is screwed into the plastic intake manifold, measures the pressure and the temperature of the intake air.Signal useThe engine control unit calculates the intake air mass from the signals and the engine speed. Depending on the calculated air mass, the boost pressure is adapted to the performance map stored in the engine control unit.Effects of signal failureSP83_33If the signal of the sender fails, the information about the throttle valve position and the signal of the intake air temperature sender G299 are used as a replacement signal. The turbocharger is only operated with regulation.Intake manifold pressure sender G71 with intake air temperature sender G42unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. intake does not guarantee accept any liability Intake manifold pressure sender (compressor) G583 with air or temperature with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� sender G520Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedThis combined sender, which is screwed to the plastic intake manifold behind the regulating flap control unit J808 measures the pressure and the temperature of the intake air in this area. Signal use Using the signal of this sender, the engine control unit controls the regulating flap control unit J808 and thus regulates the supercharger boost pressure. At the same time, the signal is used to protect the components against high temperatures. The supercharger power is throttled once the temperature of the intake air is above 130 °C.SP83_34Effects of signal failure If the combined sender fails, the supercharger boost pressure cannot be regulated and its operation is no longer possible. The turbocharger is only operated with regulation. The engine power is reduced in the lower speed ranges.Intake manifold pressure sender (compressor) G583 with intake air temperature sender G52028GB Charge pressure sender G31 with intake air temperature sender G299This combined sender is screwed into the plastic intake manifold just in front of the throttle valve module J338. It measures the pressure and the temperature of the intake air in this area. Signal use The signal from the charge air pressure sender G31 is used by the engine control unit to control the boost pressure of the turbocharger via the charge pressure control solenoid valve N75. The signal from the intake air temperature sender G299 is used to calculate a correction value for the boost pressure, whereby the temperature influence on the density of the charge air is taken into consideration. Effects of signal failure If the signals of both senders fail, the turbocharger is only operated with regulation. The boost pressure is reduced and the engine power drops.SP83_35Charge pressure sender G31 with intake air temperature sender G299Ambient pressure senderThe sender is integrated in the engine control unit and measures the ambient air pressure. Signal use The sender signal for the charge pressure value is used as a correction value for boost pressure regulation as the density of the air falls as the altitude rises. Effects of signal failureProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�If the sender for ambient pressure fails, the turbocharger is only operated with regulation. Higher emissions values and a loss in engine power can occur.SP83_36GB29 Engine managementThrottle valve module J338 with throttle valve drive angle sender 1 G187 and throttle valve drive angle sender 2 G188The throttle valve module J338 with throttle valve drive angle senders G187 and G188 is located at the end of the intake manifold in front of the intake module. Signal use Using the signals from the angle senders, the engine control unit recognises the position of the throttle valve and can control it accordingly. Effects of signal failure If a sender fails, system components such as the cruise control system (Tempomat) will be switched off. If both senders fail, the throttle valve drive will be switched off and the engine speed is limited to 1500 rpm.SP83_37The throttle valve module J338 with throttle valve drive angle sender 1 G187 and throttle valve drive angle sender 2 G188Regulating flap control unit J808 with regulating flap potentiometer G584The regulating flap potentiometer G584 is integrated in the regulating flap control unit J808, which is located in the intake duct behind the air Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted filter. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Signal use Using the signal of the regulating flap potentiometer G584, the engine control unit recognises the position of the regulating flap and can control it accordingly. Effects of signal failure If the signal fails, the regulating flap remains constantly open and the supercharger is no longer activated.SP83_38Regulating flap control unit J808 with regulating flap potentiometer G58430GB Accelerator position sender G79 and accelerator position sender 2 G185The two senders G79 and G185 are part of the accelerator module and operate as contact-free inductive senders. Signal use The engine control unit uses the signals to determine the accelerator position or to calculate the torque required by the driver. For safety reasons, there are two senders whose values are compared with each other just as with the throttle valve module J338.SP83_39Accelerator position senders G79 and G185Signal failure of one senderSignal failure of both sendersIf the signal of one sender fails, the system If the signals of both senders fail, the engine will initially switches to idle. If the second sender only run with an increased idle speed (maximum is recognised in the idle position within a certain 1500 rpm) and will no longer respond to the acProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability test time, the journey can be continued. celerator pedal. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� At the required full load, the engine speed is only increased slowly.GB31 Engine managementBrake pedal position sender G100The brake pedal position sender operates according to the principle of the Hall effect and is screwed to the master brake cylinder. It recognises whether the brake pedal is being pressed. Signal use Using the signal of the brake pedal position sender, the brake lights are operated via the onboard supply control unit (BCM). Furthermore, the signal of the engine control unit SP83_44 prevents the vehicle accelerating if the brake and accelerator pedals are pressed at the same time (the fuel injection quantity is reduced or the ignition time and the throttle valve position Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted are adjusted). unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or acceptBrake any liability pedal position sender G100with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Function For safety reasons, the Hall senders integrated in the body of the sender G100 interact to detect if the brake pedal has been pressed. When the brake pedal is pressed, the pressure rod in the master brake cylinder moves the piston with magnetic ring (permanent magnet), which passes both Hall senders. In the following explanation, only Hall sender 1 with its signal patterns is described for reasons of simplification. The signals from sender 2 are in the opposite direction.Brake pedal not pressedWhen the brake pedal is not pressed, the piston with the magnet ring is in the rest position, this means in front of the Hall senders. The evaluation electronics of the brake pedal position sender G100 issues a signal voltage of 0 - +2 V to the engine control unit and the onboard supply control unit. This signal indicates that the brake pedal has not been pressed.Piston with magnetic ring in front of the Hall sendersEvaluation electronics of the sender G100 Hall sender 1 Hall sender 2SP83_4632GB Brake pedal pressed When the brake pedal is pressed, the piston with the magnetic ring is pushed over the Hall sender. When the piston with the magnetic ring crosses the switching points of the Hall senders, the evaluation electronics issues a signal voltage, which is up to 2 volts below the onboard supply voltage, to the engine control unit. This signal indicates that the brake pedal has been pressed.Piston with magnetic ring over the Hall sendersHall senderHall sender 1 - signal increasesHall sender 2 - signal decreasesSP83_47Electrical circuit - The voltage for the brake pedal position sender G100 is supplied via the voltage supply relay J681 (terminal 15). - The earth connection is via the earth point of the vehicle body. - The two output signal lines go to the engine control unit J623. The signal also goes from one cable to the onboard supply control unit (BCM) J519, which operates the brake lights.J681J519SSS G100AProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability J623 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP83_45Voltage supply of the sender G100 Earth Output signal of sender G100 A S Battery FuseEffects of signal failure If the signal of one of the two senders fails, the injection quantity is reduced and the engine has less power.GB33 Engine managementFuel pressure sender - high pressure G247The fuel pressure sender G247 is on the lower part of the intake manifold on the flywheel side and is screwed into the high-pressure fuel tank (rail). It measures the fuel pressure in the high-pressure fuel system and transmits the measured value to the engine control unit. Signal use The engine control unit evaluates the information about the fuel pressure value and regulates the pressure in the high-pressure fuel tank (rail) via the fuel pressure regulator valve N276.SP83_48Effects of signal failureFuel pressure sender - high pressure G247If the signal of the sender G247 fails, the fuel pressure regulator valve N276 is switched off or opened, which decreases the fuel pressure in the rail. This reduces the power and the engine torque drastically.Knock sensor 1 G61The knock sensor 1 G61 is screwed to the cylinder block below the supercharger. The signals from the sensor are used to detect knocking combustion in specific cylinders. Signal use When engine knock is recognised in the corresponding cylinder, the ignition angle is adjusted by the engine control unit as a response until there is no more knocking. Effects of signal failureProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�If the knock sensor 1 G61 fails, the ignition angle of all cylinders is set to a fixed value in the "late" direction. This leads to an increase in fuel consumption and the power as well as the engine torque are reduced.SP83_49Knock sensor 1 G6134GB Coolant temperature sender G62The sender G62 is located on the coolant distributor housing, there it measures the coolant temperature. The information of the measured value is forwarded to the engine control unit. Signal use Using the signal of the coolant temperature sender, the engine control unit calculates the injection quantity and the ignition time. Effects of signal failure If the signal of the sender fails, the coolant temperature is calculated by the engine control unit according to the engine map.SP83_41Coolant temperature sender G62Radiator outlet coolant temperature sender G83This temperature sender (NTC - negative temperature coef ficient thermistor) is located in the side wall of the radiator body and measures the initial temperature of the coolant leaving the radiator outlet. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Signal useunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The radiator fan is controlled by comparing both signals from the coolant temperature sender G83 and the sender G62. Effects of signal failure If the signal of the sender G83 fails, the temperature from the sender G62 is used as a substitute value.Coolant temperature sender G83SP83_40GB35 Engine managementLambda probe G39 with lambda probe heating Z19The lambda probe G39 is a linear lambda probe and is screwed into the exhaust pipe in front of the catalytic converter close to the engine. The linear lambda probe makes it possible to drive with lambda 1 in almost all engine modes. The lambda probe is used to determine the residual oxygen content in the exhaust, whereby the air-fuel ratio in the combustion chamber is maintained. The lambda probe heating ensures that the lambda probe reaches its operating temperature very quickly.Signal use The signal of the lambda probe is used to evaluate the timing of the fuel injection. Effects of signal failure If the signal of the lambda probe G39 in front of the catalytic converter fails, there will be no lambda control and the engine runs in emergency mode using the performance map stored in the engine control unit.unless authorised after by ŠKODA catalytic AUTO A. S. ŠKODAconverter AUTO A. S. does not guarantee or with accept anylambda liability Lambda probe G130 probe heating Z29 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedSP83_50Lambda probe G39 with lambda probe heating Z19The lambda probe G130 is a step-type lambda probe and is screwed into the exhaust pipe after the catalytic converter. The lambda probe G130 determines the residual oxygen content in the exhaust. The lambda probe heating ensures that the lambda probe reaches its operating temperature very quickly. Signal use The signal of the lambda probe G130 after catalytic converter is used to check the catalytic converter function and the lambda control loop. Effects of signal failure If the signal of the lambda probe G130 after catalytic converter fails, the lambda control continues however the catalytic converter function will no longer be monitored.Lambda probe G130 with lambda probe heating Z29SP83_5136GB Brake servo pressure sensor G294The sensor G294 is located in the hose between the intake module and the brake servo and measures the pressure in the brake servo. Signal use Using the signal of the pressure sensor G294, the engine control unit recognises whether the vacuum is suf ficient for the operation of the brake servo, if the vacuum is too low, the air conditioning system is switched off. This closes the throttle valve slightly and the vacuum pressure rises again.SP83_53Effects of signal failureBrake servo pressure sensor G294If the signal of the sensor G294 fails, a substitute value from the performance map stored in the engine control unit is used, with which the corresponding parameters are calculated.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB37 Engine managementActuatorsMotronic current supply relay J271The Motronic current supply relay is located on the left of the holder for the onboard supply control unit (BCM) under the dash panel insert. Function Using the current supply relay, the engine control unit can carry out certain functions and work in run-on mode even after the engine has been switched off (ignition OFF). In this operating mode, the pressure senders are compared with each other or the radiator fan is operated. Effects of functional failureMotronic current supply relay If the current supply relay fails, the corresponding J271 sensors and actuators are no longer triggered. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Theunless engine switches and can also no authorised by ŠKODA off AUTO A. S. Š KODA AUTO A. S. longer does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� be started.SP83_56Ignition coils 1 - 4 with output stages N70, N127, N291, N292The ignition coils with output stages are located in the centre of the cylinder head. Function The ignition coils with output stages have the task of igniting the fuel-air mixture at the correct time. The ignition angle is separately controlled for each cylinder. Effects of functional failure If an ignition coil fails, the injection of the relevant cylinder will be deactivated. Deactivating the ignition coils is possible with a maximum of one cylinder.SP83_57Ignition coils with output stages N70, N127, N291, N29238GB Throttle valve module J338 with throttle valve drive G186The throttle valve module J338 with the throttle valve drive G186 is located at the end of the intake manifold in front of the intake module. Function The throttle valve drive is an electric motor that is operated by the engine control unit. The electric motor operates the throttle valve via a gear mechanism. The adjustment range is continuous from idle to full load setting, at which the throttle valve is fully opened. Effects of functional failure If the throttle valve drive fails, the throttle valve will move automatically to the emergency position. An entry is made in the faul memory and the warning light lights up to indicate a fault of the electronic accelerator control. The convenience and safety systems, which influence the torque, are switched off.Throttle valve module J338 with throttle valve drive G186SP83_58Regulating flap control unit J808 with regulating flap position control motor V380The regulating flap control unit J808 with regulating flap position control motor V380 is located in the intake duct behind the air filter.FunctionProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The regulating flap position control motor is controlled by the engine control unit. It operates the control flap continuously. Depending on the regulating flap position more or less compressed air flows back to the supercharger. This regulates the boost pressure after the supercharger. Effects of functional failure If the control motor fails, the regulating flap will move automatically to the emergency mode position (fully open). At the same time, the supercharger is deactivated.GBSP83_59Regulating flap control unit J808 with regulating flap position control motor V38039 Engine managementCamshaft adjustment valve 1 N205The solenoid valve for camshaft adjustment N205 is located in the camshaft housing and is incorporated in the oil circuit. Function The solenoid valve N205 is actuated by the engine control unit. The valve N205 distributes the oil pressure in the vane adjuster of the camshaft based on the direction and path of the camshaft adjustment. Depending on which oil channel in the adjuster is opened by the valve N205, the camshaft is adjusted in the (early/late) direction as required. Effects of functional failure If the valve N205 fails, a camshaft adjustment of the inlet valves is no longer possible and the camshaft is held in the basic position. This results in a rapid loss of engine torque.Camshaft adjustment valve 1 N205SP83_61Charge pressure control solenoid valve N75The charge pressure control solenoid valve N75 is screwed to the non-return valve for crankcase ventilation. Function The charge pressure control solenoid valve N75 is clocked by the engine control unit Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted and switches the control pressure (which conunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� sists of intake pressure combined with boost pressure) in the pressure capsule for charge pressure control. The pressure capsule operates the bypass valve (wastegate) which diverts part of the exhaust gases passed the turbine to the exhaust system. This regulates the turbine SP83_62 power and the boost pressure. Effects of functional failure If the valve N75 fails, the boost pressure is directly applied to the diaphragm in the pressure capsule. The maximum boost pressure is thus limited to the basic boost pressure value. Therefore the engine power is reduced.40GBCharge pressure control solenoid valve N75 Turbocharger air recirculation valve N249The electrical turbocharger air recirculation valve N249 is screwed to the turbocharger housing.Function The turbocharger air recirculation valve N249 prevents disturbing noises of the turbocharger and damage to the compressor wheel of the turbocharger upon switchover to boost mode and when a sharp drop in speed of the turbocharger occurs. Upon switchover to boost mode, the continuously delivered charge air accumulates in the turbocharger housing. The pressure of the accumulatSP83_63 ed charge air would rise continuously and brake the compressor wheel of the turbocharger which Turbocharger air recirculation valve N249 in turn would reduce the pressure of the charge air and lead to disturbing noises of the turbocharger. To avoid this, the turbocharger air recirculation valve N249 is opened electrically. This opens a bypass duct through which the compressed air is led back via the compressor wheel of the turbocharger to the intake side of the turbocharger. This is how the compressor wheel obtains Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability its speed. When the throttle valve isunless opened, with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� the turbocharger air recirculation valve N294 is closed and the boost pressure is immediately available again. Effects of functional failure If the air recirculation valve N249 is leaking, the boost pressure is reduced and therefore also the engine output. If the valve N249 can no longer be operated, there will be disturbing noises from the turbocharger in boost mode.GB41 Engine managementMagnetic clutch for supercharger N421The magnetic clutch for supercharger N421 is part of the coolant pump module. It is used to activate the supercharger whenever necessary. Function The magnetic clutch for supercharger is engaged by the engine control unit. The magnetic clutch then closes and forms a positive connection between the coolant pump pulley and the magnetic clutch pulley for the supercharger. Effects of functional failure If the magnetic clutch N421 fails, the supercharger can no longer be operated.Magnetic clutch for supercharger N421SP83_64Coolant pump moduleThe magnetic clutch is controlled with the PWM signal.Clutch liningProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee orcoil accept any liability Electromagnetic with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Friction plateDesignThe magnetic clutch consists of the following components: - a coolant pump pulley with a spring-loaded friction plate (screwed to the coolant pump drive shaft) - a magnetic clutch pulley mounted on bearings for the supercharger with a clutch lining (mounted pivotably in a two-row deep-groove ball bearing on the coolant pump housing) - a magnetic coil (mounted permanently to the coolant pump housing)Coolant pump impellerSP83_65Pulley for supercharger magnetic clutchCoolant pump pulley42GB Function description:Clutch liningMagnetic clutch - not engagedAFriction plateThe coolant pump pulley is driven by the crankshaft via the ancillary components drive belt. As the magnetic clutch is not engaged, the compressor belt pulley does not turn. Thus, the supercharger is not driven. A gap “A” is present between the clutch lining and the friction plate.SP83_66Pulley for electromagnetic clutch for superchargerCoolant pump pulleyMagnetic clutch - engaged When the supercharger should be activated, a voltage is applied to the magnetic coil. An electromagnetic force field is formed. The magnetic clutch then closes and forms a positive connection between the coolant pump pulley and the magnetic clutch pulley for the supercharger. The supercharger is driven. It operates until the power circuit for the magnetic coil is interrupted. The friction plate is returned by springs on the coolant pump pulley and the supercharger pulley then no longer rotates.Magnetic coilSP83_67Magnet fluxProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB43 Engine managementFuel pump control unit J538The fuel pump control unit J538 is mounted under the rear seat bench in the cover of the electrical fuel pump. Function The fuel pump control unit J538 receives a signal from the engine control unit and controls the electrical fuel pump G6 with a PWM signal (pulsewidth modulation). It regulates the pressure in the low-pressure fuel system between 0.05 - 0.5 MPa (0.5 - 5 bar). The pressure is raised to up to 0.64 MPa (6.4 bar) for warm and cold starts. Effects of functional failure If the fuel pump control unit fails, the engine can no longer be operated.Fuel pump control unit J538SP83_68Fuel pump G6The electric fuel pump G6 and the fuel filter are combined in the fuel delivery unit. The fuel delivery unit is located in the fuel tank. Function The electrical fuel pump delivers the fuel in the low-pressure fuel system to the high-pressure fuel pump. It is controlled with a PWM signal from the fuel pump control unit J538. The electrical fuel pump G6 supplies as much fuel as the engine requires. Effects of functional failureProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODAFuel AUTO pump A. S.� G6SP83_69If the electrical fuel pump fails, the engine can no longer be operated.44GB Injection valves N30 - N33The injection valves are inserted in the cylinder head. They inject the fuel directly into the cylinder at high pressure. Function The injection valves must atomise and precisely inject the fuel in a very short time. For example, double fuel injection during an operating cycle. The first time during the intake stroke and the second time before the compression stroke (approx. 50° before ignition TDC) to warm up the catalytic converter quickly.SP83_70Injection valves N30 - N33Multi-port injector The injector has a nozzle with 6 fuel outlet bores. The individual jets are arranged so that the combustion chamber parts do not become wet and air-fuel mixture is distributed evenly. The maximum injection pressure of the valve is 15 MPa (150 bar).High-pressure injectorEffects of functional failureProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted A faulty injector is detected by the fault recogniunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarante