TECHNICAL DOCUMENTATION
SSP 089 Sensors and senders in Škoda vehicles – Safety and Convenience

This PDF is currently unavailable.
Read document text
Sensors and senders in Škoda vehiclesSafety and ConvenienceSelf-study programmeProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�ŠKODA Service®89Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�2GBContents1. Safety 1.1. Airbag sensors .......................................................................................................................................................................................................6 1.2. ABS/ESC sensors.................................................................................................................................................................................................8 1.3. Headlight sensors ..............................................................................................................................................................................................11 1.4. Power steering sensor................................................................................................................................................................................... 132. Convenience 2.1. Rain sensor ...........................................................................................................................................................................................................16 2.2. Parking distance sensors............................................................................................................................................................................. 17 2.3. Sensors of the central locking system (KESSY system) ..............................................................................................................19 2.4. Air conditioning and heating sensors ................................................................................................................................................. 22 2.5. Navigation sensors ........................................................................................................................................................................................39 2.6. Sensors of the Start-Stop system ......................................................................................................................................................... 43 2.7. Accelerator pedal position sensor ..........................................................................................................................................................46You will find the instructions for the installation and removal, repair, diagnosis as well as detailed user information in the workshop manuals, the diagnosis units VAS and in the onboard literature. The time for going to press was on the 11/2011. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted This brochure is not subject to an update. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB34DriveSafetyPA ,PDCsensorHigh-pressur esenderPr e ( El s s u r ec t ro e se nic n d e so r ft he au Ab to ma s o (D l t ic u ie s te ge p el ar b en re s s ox gin ure ) ec on s ens t ro or l) Su c ti on air qu an tit ys en so rSteer ingMdtoProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�r quesendeHig (Co h-pr mm e s s on ure Ra s il in end je c er t io ns La ys mb te da m) pro be Ste er irngStewh Fu eer ieengl ro lp re sGBangl etat suio n resensse seorns ndor erGBAn g ( N le s e av ig a ns o r t io n) Ra i ( W n / li g in d h t s sc r e e ens n w or ip e rs, PA , PD Cs li g enProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Ac c p o ele r si t a io n to r se pe d a nd er l An gu la r po si t io n se n so rLoAcngceitulerdinatialonandla tese ( A i ns o rba r g)r al a s e c ce l e ns o r r a t io s( Ro AB n tat S) io n al sp ee ds en so (of r th ev eh A n g icl e i le s e nc Ro li n n s o ati r tat on io n ) al sp ee ds en s ( A B or S)A ir q Te ualit mp y s ( he er a ens t o a s y t in g ure / r s te an hum m) da ir c idi t y on s di t e ns io n or in gSP89_01ht sos) rConvenience51.1. Airbag sensorsAirbag system• airbags • crash sensors • central airbag control unit • electrical installation • front airbag switch on the front passenger side • belt tensionerThe airbag control unit receives signals from the acceleration sensors, the pressure sensors and the CISS sensor; in the event that the sensors communicate information that a crash has occured, the control unit transmits an activation signal to the respective group of airbags and belt tensioners. The airbag system is thus firmly connected to the belt tensioners (older vehicles are not equipped with electrically operated belt tensioners).front airbag on the driver's sidecentral airbag control unitfront airbag on the front passenger sideknee airbagExternal crash sensorsTwo types of external crash sensors are connected to the airbag control unit. These are pressure and acProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted celeration sensors which transmit data to the airbag unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� control unit. Pressure sensors, which are housed in the "dry" area of the driver and front passenger door, are used for detecting a side crash. An additional acceleration sensor which is located in the lower part of the C-pillar and detects a side crash which does not deform the front door, must be used in order to detect a crash on vehicles with rear side airbags, respectively head airbags. pressure sensor in the front doorAirbag systembelt tensioner of the driver's seat belt The airbags are deployed depending on the delay, the angle and the side on which the crash occured.acceleration sensor located in the lower part of the C-pillar6GBActivation system of the airbagsThe airbag deployment system consists of the central airbag control unit and four external sensors for the detection of a lateral crash.Airbag control unitThe airbag control unit is located in the interior on the middle vehicle tunnel, in which three collision detection sensors are integrated. Two sensors operate according to the principle of negative vehicle acceleration (acceleration sensors), one for detecting a frontal collision, the other one for detecting a side collision. The third and newly employed sensor, the so-called CISS sensor (Crash Impact Sound Sensing), is used as an additional sensor for the detection of a frontal collision and operates according to the principle of acoustic wave level measurement.ledges of the head airbagsbelt tensioner of the seat belt on the rear seatCISS sensorThe CISS sensor is used in the Yeti model. The CISS sensor uses the sound waves which spread out in the solid structure of the chassis and the body when the vehicle is deformed during a crash. Based on the characteristics of the measured signal, the algorithm of the control unit can determine the type of crash and can trigger the impulse which deploys the airbags and the seat belt tensioners. The CISS sensor replaces one acceleration sensor in the airbag control unit (for example on the Superb ll model, the signal of three acceleration sensors, two of which are integrated in the airbag control unit, is required in order to deploy an airbag during a frontal collision). An acceleration Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorisedsensor, by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept which detects the collision strength and the any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� vehicle deceleration as well as the CISS sensor, which detects the acoustic waves, are used for the detection of a frontal collision. In order to deploy the airbags, the acceleration signal as well as the sound signal must be measured. The sensor can detect acoustic vibrations in the range of 400 Hz - 16 Hz. Thanks to the use of the CISS sensor, it is no longer necessary to fi t an additional acceleration sensor at the front end, as in the case of the model Superb ll.SP89_7The seat belt reel of the middle rear seat is not fi tted with a belt tensionerGB71.2. ABS/ESC sensorsBased on the information received from the sensors/senders, it is evaluated in which direction the vehicle accelerates or decelerates and whether it revolves around its own axis using various functions of the wheel slip control and assist systems. The control systems can use this data in order to determine the actual direction of vehicle motion or the force acting on the vehicle and this may influence the direction of movement to some extent. Highly sensitive sensors/ senders are used to detect a critical driving situation already in the beginning phase and thus the corresponding measures can be initiated.Turning angle speed along the vertical axis of the vehicleLateral forcesAcceleration and deceleration forcesLateral forcesSP89_8Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability along the longitudinal withInclination respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Inclination along the transverse axis of the vehicleaxis of the vehicleWheel rotationvalues measured by the sensors/senders recalculated values centre of gravity of the vehicle• The ABS system uses the wheel speed sensors for determining the wheel rotation speed. • The ESC system, as opposed to the ABS system, also uses the acceleration sensors and the turning angle sensors in order to evaluate the direction of the vehicle motion on the basis of the centrifugal forces acting on the vehicle.8GBABS/ESC control unitSensors/sendersActuatorsPushbuttonHydraulic unit Brake light switchSteering angle sensorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Return pumpSpeed sensorSP89_9*The sensor unit for the acceleration is integrated in the ESC control unitGB9ESC system ABS systemWheel speed sensor - active sensors, which operate on the Hall effect principle, are used - the wheel speed is measured depending on the alternating frequency of the Hall voltage, which increases in line with increasing speed low frequency Steering angle sensor - optical sensor or Hall sensor; depending on vehicle class and year of manufacture - the optical sensor is built into the steering column, the Hall sensor is an integral part of the power steering high frequencySP89_11 SP89_10low engine speedhigh engine speedThe ESC system, fitted to the models Fabia and Roomster, includes a steering angle sensor.Turning angle sensor of the vehicle - the sensor is integrated in the ESC control unit (older models had separated sensors under the rear seats or below the steering wheel) Acceleration sensor - the transverse and longitudinal acceleration sensors are integrated in the ESC control unitProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The pressure sensor - is integrated in the ESC unitSP89_12You will find a detailed description of the sensors/senders in the Self-Study Programme No. 82.10GB1.3. Headlight sensorsAFS control unitA new technology of the headlight control is used in the vehicle Škoda Superb II: MASTER - SLAVE. The main control unit of the AFS system, the so-called MASTER unit, is located in the interior of the vehicle behind the air conditioning system and is connected to the CAN bus drive. The MASTER control unit communicates via the CAN data bus with two subordinate SLAVE units, the so-called functional units, which take over the control of the stepper motors. Each headlight is equipped with a SLAVE unit. The complete system consists of the MASTER control unit and two SLAVE functional units.MASTER control unitSLAVE functional unitSP89_13SP89_14The AFS control units receives the required information from other control units via the CAN data bus. Das AFS control unit evaluates the following input information: - angle and direction of steering wheel rotation - vehicle speed - reverse gear selector - if the low beam / main beam light up - sender of the longitudinal inclination of the vehicle LWR - switching on the windscreen wipers - speed of the individual wheels - outer luminous intensity, determined by the light sensor - position of the rotary light switch - from the ESC system On the basis of this information, the AFS control unit controls the headlight swivelling and switches into the individual light modes.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB11Overview of the system control unit of the "intelligent" front headlights in the vehicle1) Bi-xenon-rotary and swivel headlights 2) SLAVE functional units 3) MASTER control unit 4) Fog lights with integrated "Corner light" function 5) Onboard supply control unit BCM 6) Connection to CAN data bus via GATEWAY 7) Sender for detecting the longitudinal inclination of the vehicle 8) Light sensorSP89_15Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�12GB1.4. Power steering sensorSteering torque sensorThe steering torque sensor measures the torque resulting from the steering wheel rotation. This sensor uses the magnetoresistive effect*. To ensure the highest possible reliability, it has two independent circuits (redundant configuration). A torsion bar is located between the input shaft and the shaft of the steering pinion. A magnetic ring with 24 magnetic poles is mounted on the input shaft. To determine the torque, always two poles are used. When the steering wheel is turned, the two pins are turned against each other depending on the size of the resulting torque. Due to the fact that the mutual position of the magnetic ring and the redundant magnetoresistive pickup element with the mutual rotation of the shafts is changed, it is possible to measure the resulting torque and to send out the information about the size as a signal to the control unit of the electromechanical power steering.SP89_16Effect of a sensor/sender failureIf both circuits of the steering torque sensor malfunction, the steering assistance no longer operates and it is necessary to replace the complete power steering SP89_17 gear. At the moment of fault detection the control unit of the electromechanical power steering calculates, on Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted the basis of the signalunless of: authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect • the steering angle sensor G85 to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�magnetic ring input shaft • the motor of the electromechanical power steering V187, a replacement signal for the motor of the electromechanical power steering so that the power steering redundant magneremains operational with assistance for a little while toresistive pickup torsion bar longer. This ensures that the interruption of the steerelement ing assistance does not occur suddenly, but slowly. The fault of the steering torque sensor is indicated by the electromechanical power steering indicator lamp K161 lighting up red. In case of failure of only one sensor circuit, the power steering continues to operate without restriction. In shaft of steering this case the fault is indicated by the indicator lamp pinion K161 lighting up yellow. In both cases it is necessary to replace the complete SP89_18 power steering gear. A redundant magnetoresistive receiving element, which is connected to the shaft of the steering pinions, * Magnetoresistive effect = Changing the resistance of the electrical conductors is attached to the magnetic ring. through the effect of the magnetic fi eld.GB13Steering angle sensorSP89_19coil spring for airbag The steering angle sensor is located under the deflection ring (for airbag). The sensor is mounted on the steering column below the steering wheel and is coupled to the changeover switch. The information regarding the turning angle and the speed of the steering wheel rotation is obtained from the signal. Both signals are first evaluated in the steering column electronics control unit and then transmitted to the control unit of the electromechanical power steering.steering angle sensorEffect of a sensor/sender failure If the steering angle sensor fails, an emergency programme is activated. The missing signals are replaced with the replacement signals. The steering assistance is maintained. The fault is indicated by the electromechanical power steering indicator lamp K161 lighting up yellow. Description of the operation The basic components of the steering angle sensor are: • encoder with two encoder rings • 7 light barriers, each always consists of a light source and an optical sensor The encoder consists of two rings • the outer ring (absolute) and • the inner ring (incremental = incremental ring).SP89_20The steering column electronics control unit (on model Škoda Octavia)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�14GBRotor speed sensor for the motor of the electromechanical power steeringThe rotor speed sensor is a component part of the engine of the electromechanical power steering and is not accessible from outside. Signal use The rotor speed sensor for the motor of the electromechanical power steering uses the magnetoresistive effect*. Its design is equal to that of the steering torque sensor. As its name implies, it detects the rotor speed for the motor of the electromechanical power steering. The information about the speed is sent to the control unit of the electromechanical power steering. Effect of a sensor/sender failure If the rotor speed sensor fails, a replacement signal for the steering wheel rotational speed is used. The steering assistance is not terminated suddenly, but slowly. The driver is made aware of the fault by the indicator lamp lighting up red.SP89_16Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP89_21* Magnetoresistive effect = Changing the resistance of the electrical conductors through the effect of the magnetic fi eld.GB152.1. Rain sensorFunction descriptionThe rain sensor is based on the optical principle of operation. The light emitting diode emits light in such a way that almost the entire amount of light is reflected on an optical sensor if the windscreen is dry. If the glass of the windscreen is covered in snow or is wet, then the reflection characteristics change, the more snow or water is on the glass surface, the less light is reflected. The new rain sensors use infrared light instead of the standard visible light used up to now. Thanks to this fact, the sensor can be accommodated in the dark part of the windscreen and thus it is not visible from the outside. Based on the measured amount of snow or rain, the sensor controls the speed of the windscreen wipers. Together with the electronically controlled drives of the windscreen wipers, the speed of the wipers can be controlled continuously at intervals. In the event of a snowstorm or if a jet of water is directed onto the windscreen - which happens for example when overtaking trucks, - the device will immediately trigger the highest speed level. The rain sensor now offers even more potential uses. It can be used, for example, to close the windows and sunroofs automatically. If this sensor is equipped with an additional light sensor, then even the low beams can be controlled: they are switched on in the dark or when entering a tunnel without any driver intervention. The rain sensors also respond to snow. For this reason they offer in the winter time not only a better view, but also a higher comfort level when operated - and thus a higher level of safety. Moreover, these sensors are much smaller than their predecessors. Due to their dimensions which are not much larger than a matchbox, it is possible to install the sensors on the inside of the windscreen without them being noticable.SP89_23 SP89_22WindscreenProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�LEDPhotodiode16GB2.2. Parking distance sensorsPA systemThe PA park assist system detects the distance in front as well as behind the vehicle by means of the ultrasonic sensors and allows semi-automatic parking in longitudinal parking spaces. The PA system carries out the following operations: - measuring the length and the depth of longitudinal parking spaces while driving - evaluating the dimensions of the parking space - determining the appropriate vehicle position for parking - evaluating the parking distance - automatic steering of the wheels on the front axle via the electromechanical power steering. At least one object must be at the end of the parking space.The PA park assist only takes over the steering of the wheels on the front axle when parking. The vehicle is moved upon actuation of the pedal by the driver.PA park assist control unitFunction PA park assist control unit The control unit of the PA park assist processes the information from the lateral ultrasonic sensors of the ESC system as well as from the steering angle sensor. On the basis of this data, the PA control unit calculates the parameters of the parking space and informs the driver via the MaxiDOT display of suitable starting positions in order to initiate the parking process. The PA control unit evaluates at the same time the suitable way to park. After completing the calculation of the parking trajectory, the electromechanical Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted power steering swivels the wheels on the front axle. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� The wheel swivel angle is determined by the PA control unit. PA park assist control unit The control unit of the PA system also fulfills the function of the PDC parking aid, which is activated by pressing the button . If the vehicle is only fitted at the factory with the parking aid control unit for PDC parking, it is not possible to exchange it retroactively for the control unit of the PA park assist and vice versa. The PA control unit, just as the PDC unit, is fi tted on the inside of the rear right wheel house. The PA control unit is connected to the CAN data bus of the drive and communicates with the other devices via the CAN data bus. Only the communication with the control unit of the radio navigation system or the radio is performed via the BAP protocol.SP89_24SP89_25GB17Lateral sensors of the PA park assistFunction Upon activation of the PA system 2 ultrasonic sensors, located on the side of the front bumper, transmit signals into the interior on both vehicle sides. When the vehicle is in motion, the ultrasonic sensors transmit the signals and receive their response, from which they then determine the distance to the surrounding objects (based on the same principle as the PDC sensors). The range of these signals corresponds approximately to the distance of 4 m. To evaluate the free space as a suitable parking space, it is necessary to have a free space of approximately 40 cm available in front as well as behind the vehicle.SP89_26The ultrasonic sensors of the PA system are inserted in plastic holders, which are mounted from the rear into the front bumper. The sensors of the PA system are larger than the sensors of the PDC parking aid and therefore they are not interchangeable.If the system of the PDC parking aid is activated by pressing the pushbutton , both lateral sensors of the PA park assist fulfill this function, just as the sensors of the PDC system, i.e. they inform the driver about the distance to the obstacle.SP89_27Lateral sensor of the PA park assistProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�18GB2.3. Sensors of the central locking system (KESSY system)The models Superb and Superb Combi are fitted with the KESSY system (Keyless Entry Start Exit System) which allows convenient unlocking/locking as well as start-up of the vehicle without actively using a remote control key (it is sufficent that the key is inside the vehicle, for example in the trouser pocket of the driver, in order to start the vehicle). The central locking function can still be activated by means of the remote control pushbuttons on the key, furthermore a component is integrated in the key to enable the communication with the KESSY system.Connection wiring diagram of the KESSY system aie b hdfProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�gSP89_28ca b c d e f g h i-instrument panel. onboard supply control unit BCM control unit of the KESSY system electrical steering column lock ESCL start button capacitive sensors in the door handles of the front doors antenna key reading coilsdatabus CAN bus transmitter wireless data transmission (125 kHz) wireless data transmission (433 MHz) wireless data transmissionGB19Keyless unlocking and locking of the vehicleCapacitive sensors, integrated in the exterior door handles of the front doors, are used for keyless unlocking or locking of the vehicle. The KESSY system is notified whether the driver wishes to unlock or lock the vehicle doors by touching the exterior door handles of the vehicle. Then the control unit of the KESSY system searches for the authorised key. This key must be located on the side of the vehicle where the door handle was touched, however not exceeding a distance of 1.5 m.SP89_29Unlocking the vehicleFor keyless unlocking of the vehicle, it is sufficient to pull the door handle or touch the capacitive sensor, integrated in the interior door handle, which enables the communication between the vehicle and the key. This communication is performed in two steps. During the first step, the KESSY keys located in the proximity of the relevant door handle are assigned to the KESSY control unit. During the second step, the keys belonging to the vehicle receive a command from the control unit of the KESSY system and are authorised. After successful authorisation, the door locks are unlocked by the onboard supply control unit BCM.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Position of the capacitive sensor for unlocking the vehicleSP89_3020GBLocking the vehicleFor keyless locking of the vehicle after closing the doors, it is necessary to touch the capacitive sensor on the surface of the exterior door handle of the front door. This ensures that communication is established between the vehicle and the key, which is performed in two steps just as for unlocking the vehicle. During the first step, the KESSY keys located in the proximity of the relevant door handle are assigned to the KESSY control unit. During the second step, the keys belonging to the vehicle receive a command from the control unit of the KESSY system and are authorised. After successful authorisation, the door locks are locked by the onboard supply control unit BCM. When the SAFE system is active and the first command is given to lock the vehicle via the capacitive sensor, the system changes to the locked state "SAFE" in accordance with the standard. When the second command is given to lock the vehicle, the system changes to the state "externally locked" (the safety lock is deactivated) within 5 s.SP89_31Position of the capacitive sensor for locking the vehicleChecking the locking the vehicle Protected of by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted After locking the vehicle via the capacitive sensor, it is not possible to carry out a renewed unlocking of the same door handle with this sensor within 2 seconds. Thus, it is possible to check that the vehicle is actually locked without calling up a renewed unlocking of the door lock.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB212.4. Air conditioning and heating sensorsAutomatic air conditioning system Climatronic- The Climatronic control unit creates optimal climate conditions and comfort in the vehicle interior (control of temperature and intake air volume). - For this purpose, the air conditioning system is equipped with the necessary senders, sensors and motors. - The part of the air conditioning system, which ensures the supply of fresh air as well as its circulation, is supplemented with the throttle valve, which is controlled with the same electric motor as the flap for the fresh and re-circulating air. - The distributor flap is controlled electrically. - The system is able to perform a self-diagnosis.SP89_32Throttle valve Fresh and re-circulating air flapProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP89_3322GBSpatial distribution of the component parts of the automatic air conditioning system - Climatronic (including the coolant circuit)In this overview, the spatial distribution of the component parts of the automatic air conditioning system in the engine compartment as well as in the passenger compartment is shown: 1 - Compressor 2 - Condenser 3 - Liquid-filled container 4 - Expansion valve F14 - Thermal switch of air conditioning system F 129 - Pressure switch of air conditioning system G17 - Outside air temperature sensor G56 - Climatronic control panel temperature sensor G89 - Suction air temperature sensor G107 - Sunlight photo sensor J255 - Climatronic control unit J293 - Fan control unit N25 - Electromagnetic clutch of the air conditioning system (G65)* - Pressure sender of air conditioning system (only for the new system control, if G65 is used, F129 is omitted)4 F129 (G65)*G89G107 J255 +G56F14 3 2 J293 N25 1 G17SP89_34G89 V85Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�V71This overview shows the component parts which are directly installed on the box of the air conditioning system. G89 - Suction air temperature sensor G192 - Footwell vent temperature sender J126 - Fresh air blower control unit V2 - Heater blower V68 - Temperature regulator flap motor V70 - Distributor flap motor V71 - Throttle valve and recirculation flap motor V85 - Air distribution flap motorV2 J126 G192 V68SP89_35V70GB23Climatronic control unit with control and display unitDescription of the operation The Climatronic control unit receives the information from the electrical and electronic components (sensors). The incoming information is processed in the Climatronic control unit depending on the set specified values. The output signals are used to control other electrical components - actuators. The control and display unit E87 is located on the Climatronic control unit J255 and both components form a whole. The sensor for the temperature in the passenger compartment is called the Climatronic control panel temperature sensor G56 and is also integrated in the Climatronic control unit. A small fan, which supplies the air from the passenger compartment to the sensor, is mounted immediately behind the sensor G56. The temperature sensor is located in the intake air stream of the small fan and thus measurement errors are avoided. The Climatronic control unit also has a fault memory. Due to this fact, it is possible to determine the failure of one of the components of the air conditioning system or the line interruption by self-diagnosis. In the event of a fault, the Climatronic control unit ensures the operation of the automatic air conditioning system in the set mode, even in the emergency mode.Control unit Climatronic J255Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�O AUTCI RON T A LIMCECONFan of dash panel temperature sensor Climatronic V42Control and display unit of the air conditioning system E87 Climatronic control panel temperature sensor G56SP89_3624GBTemperature controlAutomatic temperature control When the air conditioning system is operating, the Climatronic takes into account the different temperature and driving conditions. In addition to the other adjustable variables of the air conditioning system, it is primarily the existing (current) temperature that is continuously compared with the specified temperature. The current temperature sensors (both external and internal temperature) are always installed at two different points. The automatic temperature control (for the temperature, air distribution and blower intensity) can be set according to personal desire.Outside temperature sensor The outside temperature is one of the fundamental output variables from which the temperature control is derived. The outside temperature is continuously recorded at two independent points. The temperature as well as the resistance dependence is the same for both sensors. The details of both outside temperature measurements are evaluated by the air conditioning control unit. The information with the lower value is used for operating the automatic control. If one of the sensors fails, the value of another sensor is used as the control variable. In case of failure of both sensors, the predetermined substitute value is used.Effect of sunlight on the temperature inside the vehicleThe outside temperature measured in °C in the front left part of the bodyThe outside temperature measured in °C at the fresh air inlet located in the box of the air conditioning systemThe specified value of the temperature in °C in the passenger compartment stored in the Climatronic control unitunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The temperature in the passenger The air temperature measured in the compartment measured in °C in the outlet channel of the air conditioning Protectedmiddle by copyright. for private or commercial of Copying the instrument panel purposes, in part or in whole, is not permitted systemGB25Senders, sensors and switchesSunlight photo sensor G107Climatronic control panel temperature sensor G56 + temperature sensor fan V42Outside air temperature sensor G17Suction air temperature sensor G89Footwell vent temperature sender G192Pressure switch of air conditioning system F129 (or the pressure sender of the air conditioning system G65 for the new system control)Additional signals: - speed signal - speed signal - hold time signalThermal switch of air conditioning system F14Thermal switch of coolant fan F18Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�26GBActuatorsClimatronic control unit J255 and control and display unit of the air conditioning system E87Air distribution flap motor V85 with position sender of air distribution flap motor G114Distributor flap motor V70 with position sender of distributor flap motor G112Temperature regulator flap motor V68 with position sender of temperature regulator flap motor G92Throttle valve and fresh air and recirculation flap motor V71 with position sender of throttle valve motor G113Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Control unit of fresh air blower J126 and heater blower V2Additional signals: - engine control unit - control unit with display in the instrument panel J285Diagnostic socket T16Electromagnetic clutch of air conditioning system N25SP89_37Fan control unit J293Coolant fan V7 and right coolant fan V35GB27Spatial distribution of sensors and sendersInterior temperature detection The selected and measured temperature in the passenger compartment is also one of the basic and necessary variables for the automatic air conditioning system. The temperature inside the vehicle is detected with two separate sensors. By means of these sensors, the Climatronic control unit receives information about the existing temperature in the vehicle interior as well as the temperature of the air flowing from the body of the automatic air conditioning system into the vehicle interior. In case of failure of one of the sensors, the fixed value is used as a replacement variable. Thus, the automatic air conditioning system can continue to operate.Sunlight - regulating variable The thermal effect of the sunlight influences the temperature comfort in the vehicle besides the outside temperature. The rays of the sunlight falling onto the photo sensor are evaluated by the Climatronic control THE IMAGE IS REPLACED WITH THE IMAGE unit. This ensures that the influence of the thermal OF THE MODEL SUPERB effect of the sunlight is also taken into account for the automatic temperature control. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Sunlight photo sensor G107SP89_38Suction air temperature sensor G89Climatronic control panel temperature sensor G56Footwell vent temperature sender G192 Outside air temperature sensor G1728GBClimatronic control panel temperature sensor with fanThe air temperature inside the vehicle is detected by the sensor, which is accommodated directly in the Climatronic control unit. From the passenger compartment, the air is blown by the fan onto the sensor. Due to the fact that it is located in the intake air stream, the measurement of the actual temperature inside the vehicle is ensured. The small fan is actuated by the control and display unit. The air flow around the sensor prevents that measurement errors occur on the temperature sensor. Signal use The measured temperature is used for comparison with the specified temperature. Based on the evaluation, the regulator flap as well as the speed of the heater blower is adjusted. Signal failure If the signal fails, the temperature of +24°C is used as a substitute value and the system continues to operate. The temperature sensor in the Climatronic control panel can perform a self-diagnosis.SP89_36O AUTONIC ATR CLIMN ECOFan of Climatronic control panel temperature sensor V42 Climatronic control panel temperature sensor G56Footwell vent temperature senderThe temperature of the air flowing from the air conditioning system into the vehicle interior is measured. A thermally sensitive resistor is used to detect the temperature. With decreasing temperature, the electrical resistance increases. Signal use The signal is used by the Climatronic control unit. It is used to control the air distribution when blowing off the air from the windscreen or in the footwell and in addition to adjust the speed of the heater blower. Signal failure In the case of signal failure, the substitute value of +80°C is calculated by the Climatronic control unit. The air conditioning system continues to operate. The temperature sensor of the air supplied to the footwell is able to perform a self-diagnosis.SP89_39NTC resistanceProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB29Outside air temperature sensorThe outside air temperature sensor is incorporated in the front part of the body. It records the actual outside temperature. Signal use Depending on the outside temperature, the Climatronic control unit adjusts the regulator flap and controls the speed of the heater blower. Signal failure If the signal fails, the information from the suction air temperature sensor G89 is used as a substitute value. In the event that G89 also fails, the air conditioning system continues to operate and the temperature of +10°C is used as a substitute value. However, the air circulation does not operate. The outside air temperature sensor G71 is able to perform a selfdiagnosis.SP89_40Suction air temperature sensorThe suction air temperature sensor can be found directly in the suction channel of the fresh air. This is the second Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted location where the actual outside temperature is by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability unless authorised with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� detected. Signal use Depending on the outside temperature, the Climatronic control unit adjusts the regulator flap and controls the speed of the heater blower. Signal failure In the case of signal failure, the value of the outside air temperature sensor G17 is used. The suction air temperature sensor G89 is able to perform a selfdiagnosis.SP89_4130GBSunlight photo sensor (single zone air conditioning system)SP89_42The sunlight influences the control of the automatic air conditioning system via the sunlight photo sensor. The unit measures the sunlight which shines on the passengers. Description of the operation The sunlight passes through the filter, the optical element and falls on the photodiode. The filter has a similar function as a pair of sunglasses. It protects the photodiode from damage due to solar radiation. The photodiode consists of a photosensitive semiconductor. If no light falls on the photodiode, only a small current can flow through it. The current flow increases through the exposure to light. The stronger the light that falls on the diode, the greater the current. Depending on the increase of current, the Climatronic control unit detects the increased solar radiation. It adjusts the regulator flap and adapts the speed of the heater blower in order to influence the temperature in the vehicle interior. Signal failure The Climatronic control unit operates with a fixed substitute value. Self-diagnosis and error messages interruption/short circuit to positive terminal. Short circuit to earth.Housing coverFilterOptical elementPhotodiodeCover/housingSP89_43Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB31Pressure switch of air conditioning systemThe pressure switch of the air conditioning system continuously monitors the pressure in the coolant circuit of the automatic air conditioning system Climatronic. It is a triple switch. It is necessary to incorporate it in the air conditioning system for safety reasons. It was also integrated in the manual air conditioning system. Tasks and operation - The pressure switch of the air conditioning system comes on when the pressure exceeds the value of 1.6 MPa. The coolant fan is switched to the next higher stage via the fan control unit. Thus, the optimal performance of the condenser is achieved. - If the pressure is too high - above 3.2 MPa (e.g. if a fault in the engine cooling occurs), the switch is opened. The air conditioning system is switched off. - If the pressure value is below 0.2 MPa - e.g. when the coolant flows out - the switch is opened. The air conditioning system is switched off. The pressure switch of the air conditioning system can be removed without suctioning off the coolant. Self-diagnosis In the self-diagnosis in function 02 - selection from the fault memory - if the operation of the pressure switch is checked when pressing 0.2 MPa and 3.2 MPa. The part of the switch of the air conditioning system, which operates at a pressure of 1.6 MPa, is not subject to any test. Wiring diagram Wiring diagramSP89_44+106/2Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP89_45F14 Thermal switch of air conditioning system - coolant temperature (+119°C) F 129 Pressure switch of air conditioning system J255 Climatronic control unit J293 Fan control unit32GBAuxiliary signal – vehicle speed "v"The information regarding the vehicle speed is necessary for the throttle valve control. The gearbox speedometer signal is fed into the control unit using the indicator of the instrument panel. Here the signal is used for the control. The signal is directly fed to the throttle valve motor via the signal cable. The speed signal is checked using the self-diagnosis. The fault can only be detected if the signal is not measured during five drive cycles (start, drive, speed above 15 km/h, engine switch-off) within four minutes after starting the vehicle.3 2 141/min x 10005 6 760 40 20120 100 140 km/h 80 160 180 200 220 240J285Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�J255V71/G113SP89_46GB33Pressure sender of the air conditioning systemPressure sender of the new generation for monitoring the pressure in the coolant circuit. The pressure sender of the air conditioning system is an electronic pressure sender, located in the high-pressure line. It detects the coolant pressure while the physical variable converts the pressure into an electrical signal. Compared to the previous pressure sender of the air conditioning system, it not only detects the predetermined pressure values, but also the coolant pressure during the course of the entire operating cycle. Signal use - in the engine control unit - in the fan control unit The engine load resulting from the air conditioning system and the pressure conditions in the coolant circuit are determined by the signal. The fan control unit ensures that the fan as well as the electromagnetic coupling of the compressor of the air conditioning system can be switched on and off on the next higher stage. Alternative function If the fan control unit does not detect any signals, the compressor of the air conditioning system must be switched off for safety reasons. Advantages - At idle speed, it is possible to accurately regulate the engine speed with the compressor of the air conditioning system according to the load. - Switching the fan stages on and off is carried out with short time delay. The change in the fan speed can hardly be detected. Self-diagnosis "fault message" The pressure sender of the air conditioning system is also stored in the fault memory of the engine electronics. e.g.: 00819 high-pressure switch G65 „signal too low“SP89_47Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�34GBFunction of the air conditioning pressure senderThe coolant pressure is supplied to the silicon quarz crystal box. Depending on the pressure, the quarz crystal is more or less deformed. Low-pressure As a result of the deformation of the quarz crystal, the electrical resistance changes. If the coolant pressure curve changes, the voltage curve resulting on the silicon quarz crystal also changes. The changes in the voltage are fed to the microprocessor (a component part of the pressure sender of the air conditioning system) and are converted into the PWM signal (pulse-width modulation signal). If the pressure is lower, the quarz crystal is deformed or altered. This means that the resulting voltage is exposed to a smaller resistance at low pressure.PWM signal Microprocessor Voltage Silicon quarz crystalSP89_48The lower the pressure, the shorter the pulse duration = smaller pulse width generated by the microprocessor. The PWM signal frequency is 50 Hz. This corresponds to the cycle duration of 20 ms = 100%. If the pressure is 0.24 MPa, the pulse lasts 2.6 ms, which represents 13% of the cycle duration.PWM signalCycle duration 20 msProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP89_49GB35High-pressure (rising)If the coolant pressure is high (rising), the quarz crystal will deform more. The electrical resistance increases. PWM signal Microprocessor Voltage Silicon quarz crystal The voltage is reduced in direct proportion.SP89_50The pulse duration (pulse width) increases in direct proportion to the pressure increase. If the pressure is 3,7 MPa, the pulse lasts 18 ms, which represents 90% of the cycle duration.PWM signal Cycle duration 20 msProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Pulse duration 18 msSP89_5136GBHeatingFunction principle of the auxiliary heatingThe fuel from the fuel tank of the vehicle (petrol or diesel) is transferred to the heating unit by means of a special pump. This is where the fuel and air mixes as it enters the combustion chamber via the venturi nozzle. The air is fed into the system by a fan, which is located in front of the nozzle, whereas the mouth of the fan is equipped with a silencer. The glow plug which extends into the combustion chamber ignites the fuel-air mixture. The heat released during the combustion heats the heat exchanger, which in turn heats the water which flows through it. The heat exchanger is connected to the coolant circuit of the vehicle. The auxiliary heating pump ensures the water circulation in the water circuit. The exhaust gases emitted as a result of the combustion process are diverted through the exhaust pipe which is fitted with a silencer. The control unit of the Thermo Top V system is a direct component of the heating unit. The temperature in the heat exchanger is detected by two sensors - temperature sensor and overheat sensor.Hot water output Venturi nozzle Combustion air fan Temperature sensor Overheat sensorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP79_8Heat exchangerSP89_52Combustion air inletFuel supply Fuel gas evacuationGB37Auxiliary heating control unitPushbutton for immediately switching on the auxiliary heatingQ8V54 G18SP89_53V55Z66 G189**R149J364LED indicator light pushbuttons for immediately switching on the auxiliary heating V6W-BusN279 CAN Additional output signals, e.g. J13 - fresh air blower relay*G18 G189 R149 W–Bus J364 Q8 V54 V55 Z66 V6 N279Temperature sensor Overheat sensor Receiver of the remote control Special databus for the connection of R149 Auxiliary heating control unit Glow plug with flame monitoring Fuel metering pump Circulation pump Combustion air fan Heater coolant shut-off valve Heating element for preheating the fuel* **Only for the model range Škoda Superb I and II Only for vehicles with diesel engines Output signal Input signal DatabusProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�38GB2.5. Navigation sensorsAlthough the positioning per satellite is the most important source of information for the GPS system, the navigation system of the vehicle can eliminate these short signal failures. This is achieved by determining the driving direction of the vehicle wheels by means of the tilt angle sensor and the distance traveled by means of the ABS speed sensor. In this case, the comparison of the signals received by the turning angle sensor and the ABS speed sensor with the signals from the GPS system is not possible and the inaccuracy of the calculated vehicle position increases if the radio signals from the GPS system are not received for a longer period of time.Vehicle tilt angle sensor. The vehicle tilt angle sensor measures the change in driving direction. It replaces the magnetic sensor, which has been used in previous models of the navigation units.SP89_54Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB39Vehicle tilt angle sensorAs already mentioned, the vehicle tilt angle sensor is a system component that aims to specify the satellite navigation. The sensor is directly integrated in the navigation unit. Advantages: - the sensor is not affected by magnetic interference - small dimensions - high sensitivity - no need for adjustment or setting If the vehicle changes the driving direction, it rotates around its vertical axis. The tilt angle sensor detects the tilting of the vehicle and transmits this information to the navigation control unit. The control unit evaluates the sensor signal and calculates the angle that the wheels deviate from the driving direction. To distinguish the driving direction (forwards or backwards), the navigation control unit receives a signal from the switch of the rear lights. To calculate the tilt radius, it is also necessary to know the length of the distance traveled. The length of the distance traveled is transmitted to the control unit by means of the signals from the ABS speed sensor. The tilt angle sensor must be installed at different points depending on the type of the radio navigation system.SP89_55Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP89_5640GBFunction of the vehicle tilt angle sensor Both legs of the sensor body are designed as an oscillating body. When switching on the ignition, the lower piezoelectric quartz crystals are energised simultaneously and begin to vibrate. The oscillation generated by the piezoelectric quartz crystals is transmitted to both legs of the body.Rotational axis of rotationLower piezoelectric quartz crystal Vibration directionVibration directionVSP89_57Coriolis force The so-called Coriolis force acts on the swinging sensor legs when changing the driving direction (cornering and the like) of the vehicle. This force acts against the rotation direction of the vehicle about its vertical axis. The upper part of the hitherto only laterally swinging legs begins to deform through the effect of the Coriolis force. When the legs deform, so do the upper piezoelectric quartz crystals, where the electrical voltage is generated by the effect of the Coriolis force. The generated voltage is supplied to the navigation control unit which evaluates it and in turn changes the driving direction of the vehicle.Rotation directionVibration directionVibration direction Upper piezoelectric quartz crystalVibration direction Vibration directionSP89_58Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB41ABSspeed sensorThe ABS speed sensor aims to specify the satellite navigation and obtains information about the distance traveled by the vehicle. The sensor is mounted on the vehicle wheel and detects the rotational speed of the respective wheel. This wheel-speed information is converted into signals which are transmitted to the ABS control unit. The control unit of the ABS system transmits this information signal to the navigation control unit which is able to evaluate the signal and to determine in this way the distance traveled by the vehicle.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP89_59Rear light switchWhen the reverse gear is engaged, the navigation control unit receives a signal from the switch of the rear lights. The navigation control unit can detect whether the vehicle is moving forwards or backwards. Effects of signal failure: - If a signal fails, the navigation control unit does not detect when the vehicle is moving backwards and the guidance is therefore less accurate.SP89_6042GB2.6. Sensors of the Start-Stop systemThe Start-Stop systems operate by cutting the engine when the driver comes to a complete standstill, e.g. for a traffic light or in traffic jams; then the engine automatically restarts by depressing the clutch pedal and the respective gear is engaged again. A special starter is provided for this system, which ensures a safe, fast and quiet engine start due to its powerful electric motor, together with the advanced noise-free gear system. This system also has a control software, which is usually implemented in the electronic engine control unit ECU, and the battery sensor, whose task it is, among others, to detect the present state of the battery charge and to transmit this information to the energy management system. Thus, it is ensured that the engine is brought only to a standstill when the battery has sufficient energy for rapid and repeated engine restarts. The system is rounded off by a crankshaft sensor, sensors on the pedals, and a deep-cycle resistant battery.Pushbutton switch for the operation of the START-STOP systemThe pushbutton switch F416 is located in the center console next to the handbrake.Function The pushbutton switch is used for activating and Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted deactivating the operation of the START-STOP system unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability while driving. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� The START-STOP system is activated automatically each time the ignition is switched on. The operation of the system itself is carried out as soon as the above-mentioned operating conditions are fulfilled and checked. Effects of signal failure If the pushbutton switch function for the operation of the START-STOP system fails, the engine control unit automatically switches off the START-STOP system. The fault is entered in the fault memory of the engine control unit. Pushbutton switch for the operation of the START-STOP system F416SP89_61GB43Battery monitor control unitThe information whether the battery has sufficient energy to repeatedly restart the engine is an important prerequisite for the operation of the START-STOP system. Therefore, vehicles with the START-STOP system are equipped with a battery monitor control unit with integrated battery sensor. The battery monitor control unit J367 is directly located on the negative pole terminal of the earth cable and is connected to the data bus diagnostic interface (Gateway) J533 via the LIN data line.SP89_62Battery monitor control unit J367Signal use The battery sensor integrated in the battery control unit J367 detects: - the b