TECHNICAL DOCUMENTATION

SSP 094 Diagnosis of the automatic gearboxes 0AM and 02E

PDFEN40 pages2 MB
SSP 094 Diagnosis of the automatic gearboxes 0AM and 02E - PDF cover

This PDF is currently unavailable.

Read document text
Diagnosis of the automatic gearboxes 0AM and 02ESelf-study programmeŠKODA Service®Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�94 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Contents1. Introduction  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4 2. Basic comparison of the gearboxes 0AM (DQ 200) and 02E (DQ 250) � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5 3. Seven-speed automatic transmission 0AM � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6 3.1 Changes in the mechanical part of the gearbox 0AM � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6 3.1.1 Design adjustments to the clutch as of 01.06.2011 (PKO2 package)  � � � � � � � � � � � � � � � � � � � � � � � � � � 6 3.2 Diagnosis  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9 3.2.1 Introduction � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9 3.2.2 Measured value blocks  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10 3.2.3 Most common faults and their rectification  � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 14 3.2.4 Diagram of the recommended procedure when repairing the seven-speed gearbox 0AM � � � � � � � � 20 4. Six-speed gearbox 02E � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 22 4.1. Diagnosis � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 22 4.1.1 Introduction � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 22 4.1.2 Measured value blocks � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 23 4.1.3 Most common faults and their rectification � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 27 4.1.4 Diagram of the recommended procedure for repairing the six-speed gearbox 02E  � � � � � � � � � � � � � 30 5.  Technical question concerning the repair of the gearboxes 0AM and 02E and the documents thereto  � � � 32Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB 1. IntroductionThis workshop teaching aid complements the previously published self-study brochures: – SSP No. 56, six-speed automatic transmission 02E – SSP No. 75, seven-speed automatic transmission 0AM Important technical modifications are described in this brochure, which have been carried out since the publication of the above mentioned SSP. The main part of the teaching aid is dedicated to describing the correct implementation of the diagnosis of the automatic gearboxes 02E and 0AM, finding the causes of problems and faults that can occur when operating vehicles with these gearboxes, as well as determining the procedure for their rectification, including references to the corresponding maintenance documentation.You will find the instructions for the installation and removal, repair, diagnosis as well as detailed user information in the diagnostic units VAS and in the onboard literature. The time for going with to press was on the 6/2012. respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� This brochure is not subject to an update.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitySP94_00E 2. Comparison of the automatic gearboxesAutomatic gearboxes 0AM and 02E – Specification Designation of gearbox Number of gears Torque transmission Design of the clutch 0AM (DQ 200) 7 up to 250 Nm The torque is transmitted by the two-plate dry clutch and by means of mechanical actuation The oil circuit of the mechatronics is separated from the oil circuit of the gearbox No heat exchanger for the oil or the coolant Electrical oil pump in the mechatronics (shifting based on need) 02E (DQ250) 6 up to 350 Nm The torque is transmitted by the oil-bathed two-plate dry clutch Mutual oil circuit for the gearbox as well as the mechatronicsOil circuitOil coolingOil coolerOil pumpThe mechanical oil pump, located on the gearbox, is permanently connectedFilling quantities of gearbox oil 1.7 ltr. 7.2 ltr. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA any liability Interval for gearbox oil change filled for life AUTO A. S. does not guarantee or acceptafter 60 000 km with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP94_14SP94_15GB 3. 3.1 Seven-speed automatic transmission 0AMChanges in the mechanical part of the gearbox 0AM3.1.1 Modification of the clutches as of 01.06.2011 (PKO2 package)On the seven-speed automatic transmission 0AM, changes in the design of the clutch were carried out as of 01. 06. 2011. The modified clutch cannot be exchanged against the original clutch which was fitted up to the stated date.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP94_01Description of the changes:a)  Design modifications to the cut-off levers of the clutches - Replacement of forgings by plate compacts (changing the lever's shape).SP94_02GB b) Modified bearing on the new version of the cut-off lever for the clutchesSP94_03SP94_04new assembly of the lever on clutch K1* (as of 01. 06. 2011)new assembly of the lever on clutch K2* (as of 01. 06. 2011)c) C  hanges to the shape of the housing on the dual-clutch and modified bearings of the clutch levers in the housing new bolt bearing of the lever on clutch K1* new bolt of the lever on clutch K1*SP94_05SP94_06new bolt bearing of the lever on clutch K2*new bolt of the lever on clutch K2*lever on clutch K2* (as of 01.06.2011)SP94_07lever on clutch K1* (as of 01.06.2011)SP94_08Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�* Designation of the individual clutches K1, K2, see brochure SSP75.GB d) Modification of the clutch lever cover (depending on the changes carried out to the shape of the lever):SP94_11SP94_12old version of the cover up to 1. 6. 2011new version of the cover as of 1. 6. 2011SP94_09SP94_10Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB 3.2 Diagnosis of the automatic gearbox 0AM3.2.1 IntroductionThe following operating modes are available in the diagnostic unit VAS: – controlled fault finding – controlled functionsThe gearbox electronics enables the following functions: – Identification services (information regarding the installation) – Coding of the gearbox control unit (code 20 for 02E and 0AM) – Reading the measured values – Basic setting - complete (checking the shifting of the gears, setting the engagement point on the clutches) – Basic setting - neutral (only before replacing the mechatronics, all the adjusters must be in the neutral position) – Modification – Fault storage in the event memory – Processing the measured values ​​ and their display in the measured value blockShifting into the basic setting is carried out in accordance with: – the mechatronics assembly – the gearbox assembly – the selector lever assembly – the installation of other control units (e.g. engine control units), ABS or diagnostic interface for data buses (Gateway)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB 3.2.2 Measured value blocksSelected measured value blocks of the gearbox electronics serve to carry out a correct fault diagnosis on the automatic gearboxes DSG.Therefore, if a fault is detected on the automatic gearbox, a printout of all the measured value blocks must be sent (at idle speed, if the vehicle is stationary or in P, N or D mode) The following information can be read in the measured value blocks (MVB): – Identification of the software and hardware level of the automatic gearbox control unit – current operating values ​​ (oil pressure values ​​ in the mechatronics, positions of the individual gear adjusters, clutch status, speeds of the individual shafts, selector lever position, etc.) – the current values recorded during the operation ​​ (journey time in the individual driving modes, operating temperatures of the clutches, journey time in all operating temperatures and warnings, etc. – specific environmental conditions when the last two faults occuredDescription of the operating mode for actuating the automatic gearbox – T he mechatronics controls the individual gearbox parts by means of its actuators. It comprises two actuation elements, each operating the corresponding clutch K1 or K2 independently. Furthermore, it comprises four actuation elements for changing the gears (1+3, 2+4, 5+7, 6+R). The positions of all the actuation elements can be checked using the measured value blocks (MVB). – It is important that the mechatronics is supplied with pressure oil in order to ensure its proper operation. Insufficient pressure can cause a jolt or a complete loss of function of the automatic gearbox. The current pressure can be checked in the MVB 30.3. – T he mechatronics alters the contact pressure exerted on the corresponding clutch depending on the transmitted torque – thus, the clutch is not permanently under continuous pressure, yet it changes while driving. –T  he state of the clutch K1 can be determined by reading the MVB 95-97, whereas the state of the clutch K2 can be determined by reading the MVB 115-117. It is possible to determine the current position of the adjuster for K1 in the MVB 91 and for K2, in the MVB 111. – T he MVB 235-244 store the environmental conditions at the last fault entry, the MVB 245-254 store the environmental conditions at the entry of the second last fault.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Important measured value blocks Measured value blocks Nbr. 4.1 5.1 5.2 5.3 5.4 80.1 30.1 30.2 30.3 Description Position of the selector lever (E313) Gearbox input speed (sender G641 / G182, i. e. in front of the clutches) Engine speed (CAN value) Input shaft speed 1 (sender G632 – behind the clutch K1) Input shaft speed 2 (sender G612 – behind the clutch K2) Manufacturing date of the mechatronics Min. permitted pressure (S4 min.) Actual pressure value (V401) Value example P (R, N, D, S, T+, T-) 766/rpm 766/rpm 0/rpm 0/rpm TFK-535 05.07.11 42.00 bar 30.34 bar (example of an incorrect/low value)Max. permitted pressure in the mechatronics (S1 max.) 60.00 bar10GB Current position of the actuation elements of the clutches (when the vehicle is stationary in P mode): Measured value blocks: Current position of the actuation elements of the clutches – Example of the values in ​​ P Nbr. 91.1 91.2 111.1 111.2 Description Desired position of the adjuster for K1 Actual value of the adjuster for K1 Desired position of the adjuster for K2 Actual value of the adjuster for K2 Value example 0.0 mm 2.1 mm 0.0 mm 2.3 mmWhile driving it is almost impossible to distinguish between the nominal or the actual value, only when the vehicle is stationary in the P or N mode is the actual position of the adjuster slightly higher than when in the desired position.Clutch characteristic curve Open final positions 250 Small play Clutch travel O. K. 150 Large play Clutch curve Closed final positions200 Power output [Nm]100500Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted Clutch travel unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A.[mm] S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�28SP94_13Blue curve: The characteristics of the clutch are O. K. Red curve:  The clutch closes already at 200 Nm, however it should transmit a torque of up to 250 Nm. The customer complains about weak engine power, the vehicle can also jolt. Yellow curve:  The clutch is engaged, which can be determined from the measured value blocks 5.3 and 5.4. GB11 State of the play and wear of K1 in the measured value blocks Measured value blocks – State of play and wear of clutch K1 Nbr. 95.1 95.2 95.3 95.4 96.1 96.2 96.3 96.4 97.1 97.2 Description Changes to the position 0 Torque for the position 0 Changes to the position 1 Torque for the position 1 Changes to the position 2 Torque for the position 2 Changes to the position 3 Torque for the position 3 Clutch K1 – Final position in the open position Clutch K1 –Final position in the closed positionExample No. 1 9.0 mm 0.0 Nm 11.7 mm 16.0 Nm 18.2 mm 153.4 Nm 21.6 mm 249.9 Nm 2.4 mm 27.4 mmExample No. 2 3.0 mm 0.0 Nm 6.7 mm 16.0 Nm 14.2 mm 153.4 Nm 20.3 mm 249.9 Nm 2.4 mm 27.4 mmExample No. 3 12.0 mm 0.0 Nm 14.7 mm 16.0 Nm 22.0 mm 153.4 Nm 26.3 mm 193.3 Nm 2.4 mm 27.4 mm95.1 minus 97.1 must be greater than 2 mm, Due to insufficient clutch play, shifting of the input shaft occurs. (This will be entered in the fault memory.) See example No. 2 and a low difference in value of the blocks 95.1 minus 97.1. 97.2 minus 96.3 must be greater than 1 mm, At a lower value the maximum torque is not transmitted and a clutch slippage occurs. The vehicle may start to jolt when driving in higher gears or when accelerating. (This will be entered in the fault memory.) See example No. 3 and a low difference in value of the blocks 97.2 minus 96.3 (subsequently a low torque is transmitted and entered in block 96.4.).State of the play and wear of K2 in the measured value blocks Measured value blocks – State of play and wear of clutch K2 Nbr. 115.1 115.2 115.3 115.4 116.1 116.2 116.3 116.4 117.1 117.2 Description Changes to the position 0 Torque for the position 0 Changes to the position 1 Torque for the position 1 Changes to the position 2 Torque for the position 2 Changes to the position 3 Example No. 1 8.3 mm 0.0 Nm 10.4 mm 16.0 Nm 17.4 mm 153.4 Nm 21.6 mm Example No. 2 3.1 mm 0.0 Nm 6.7 mm 16.0 Nm 14.2 mm 153.4 Nm 20.3 mm Example No. 3 12.0 mm 0.0 Nm 14.7 mm 16.0 Nm 22.0 mm 153.4 Nm 26.3 mm 193.3 Nm 2.4 mm 27.4 mmTorque for the position 3 249.9 Nm 249.9 Nm unless authorised by Š KODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilityrespect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Clutch K2 with – Final position in the open position 2.4 mm 2.4 mmProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedClutch K2 –Final position in the closed position27.4 mm27.4 mm115.1 minus 117.1 must be greater than 2 mm, Due to insufficient clutch play, shifting of the input shaft occurs. (This will be entered in the fault memory.) See example No. 2 and a low difference in value of the blocks 117.1 minus 115.1. 117.2 minus 116.3 must be greater than 1 mm, At a lower value the maximum torque is not transmitted and a clutch slippage occurs. The vehicle may start to jolt when driving in higher gears or when accelerating. (This will be entered in the fault memory.) See example No. 3 and a low difference in value of the blocks 117.2 minus 116.3 (subsequently a low torque is transmitted and entered in block 116.4.).12GB Modification of the clutches Measured value blocks: Modifications of the clutches K1 and K2 Nbr. 180.1 180.2 200.1 200.2 Description Clutch 1 – number of successful changes Clutch 1 – last successful change made to the mileage travelled (in km) Clutch 2 – number of successful changes Clutch 2 – last successful change made to the mileage travelled (in km) Value example 236 15 240 km 322 15 410 kmThe minimum value for a new vehicle amounts to 50 successful changes. Further changes are ​​ continuously carried out while driving. In special cases and in specific driving modes, it may happen that it is not possible to carry out this change over an extended period of time and thus the vehicle becomes uncomfortable when shifting. This can be traced back from the MVB for the last successful change. In such a case it is necessary to perform a basic setting and to carry out a test drive according to the instructions in the VAS.Printout of the environmental conditions for the last two faults stored in the event memory All collision values ​​ from the measured value blocks are stored in the event memory. In this way, a printout of the environmental conditions for the last as well as the second last recorded faults is stored. An example of a printout for the environmental conditions from the fault memory is provided below. Printout of the environmental conditions when the last fault was recorded:235_1 snapshot 1 ID of the fault 116 235_2 snapshot 1 km 68340 km 235_3 snapshot 1 counter 11 235_4 snapshot 1 pressure supply, actual pressure 48.50 bar 236_1 snapshot 1 selector lever pos. P 236_2 snapshot 1 vehicle clutch 0x0014 236_3 snapshot 1 desired gear 7 236_4 snapshot 1 preselected gear 6 237_1 snapshot 1 speed, drive 1056/rpm 237_2 snapshot 1 speed, output 2496/rpm 237_3 snapshot 1 shaft speed 1 1 088 /rpmProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised ŠKODA AUTO A. S. does not guarantee or accept any liability 237_4 snapshot 1 239_2by snapshot 1 AUTO A. S. ŠKODA241_1 snapshot 1 actuation elements ofof the shaft speed 2 192/rpm accelerator pedal 0.00 % with respect to the correctness information in this document. Copyright by ŠKODA AUTO A. S.� 238_1 snapshot 1 gears 2-4, actual current 241_2 snapshot 1 actual position engine torque with external of the valve 0.528 A actuation elements 239_3 snapshot 1 depressions -7.8 Nm actuation elements of the 241_3 snapshot 1 of the gears 1-3 -0.3 mm 238_2 snapshot 1 gears 5-7, actual current part transmission 1, actual actual position of the valve 0.540 A current of the valve 0.588 A actuation elements 239_4 snapshot 1 241_4 snapshot 1 actuation elements of the part transmission 2, actual of the gears 2-4 -0.3 mm 238_3 snapshot 1 gears 6-R, actual current current of the valve 0.570 A actual position 242_1 snapshot 1 of the valve 0.528 A actuation elements 240_1 snapshot 1 voltage actual position of the of the gears 5-7 -0.3 mm of terminal 15 14.2 V 238_4 snapshot 1 242_2 snapshot 1 clutch 1 12.8 mm actual position 240_2 snapshot 1 voltage of terminal 30, actuation elements actual position of the electric motor 14.2 V 242_3 snapshot 1 of the gears 6-R -0.2 mm clutch 2 20.8 mm 239_1 snapshot 1 240_3 snapshot 1 hybrid temperature 0.0 °C actuation elements of the clutch 1, actual current 242_4 snapshot 1, gears 1-3, actual current temperature of the valve 0.000 A 240_4 snapshot 1 of clutch 1 and 2, of the valve 0.534 A clutch 2, actual current maximum 90.0 °C of the valve 0.000 APrintout of the environmental conditions when the second last fault was recorded:245_1 snapshot 2 ID of the fault 117 245_2 snapshot 2 km 68340 km 245_3 snapshot 2 counter 12 245_4 snapshot 2 pressure supply actual pressure 48.50 bar 246_1 snapshot 2 selector lever pos. P 246_2 snapshot 2 vehicle clutch 0x0014 246_3 snapshot 2 desired gear 7 246_4 snapshot 2 preselected gear 6 247_1 snapshot 2 speed, drive 1056/rpm 247_2 snapshot 2 speed, output 2496/rpm 247_3 snapshot 2 shaft speed 1 1088 /rpm 247_4 snapshot 2 shaft speed 2 192/rpm 248_1 snapshot 2 actual position actuation elements of the gears 1-3 -0.3 mm 248_2 snapshot 2 actual position actuation elements of the gears 2-4 -0.3 mm 248_3 snapshot 2 actual position actuation elements of the gears 5-7 -0.3 mm 248_4 snapshot 2 actual position actuation elements of the gears 6-R -0.2 mm 249_1 snapshot 2 actuation elements of the gears 1-3, actual current of the valve 0.534 A 249_2 snapshot 2 actuation elements of the gears 2-4, actual current of the valve 0.528 A 249_3 snapshot 2 actuation elements of the gears 5-7, actual current of the valve 0.540 A 249_4 snapshot 2 actuation elements of the gears 6-R, actual current of the valve 0.528 A 250_1 snapshot 2 actual position of the clutch 1 12.8 mm 250_2 snapshot 2 actual position of the clutch 2 20.8 mm 250_3 snapshot 2 clutch 1, actual current of the valve 0.000 A 250_4 snapshot 2 clutch 2, actual current of the valve 0.000 A 251_1 snapshot 2 accelerator pedal 0.00 % 251_2 snapshot 2 engine torque with external depressions -7.8 Nm 251_3 snapshot 2 part transmission 1, actual current of the valve 0.588 A 251_4 snapshot 2 part transmission 2, actual current of the valve 0.570 A 252_1 snapshot 2 voltage of terminal 15 14.2 V 252_2 snapshot 2 voltage of terminal 30, electric motor 14.2 V 252_3 snapshot 2 hybrid temperature 0.0 °C 252_4 snapshot 2 temperature of clutch 1 and 2, maximum 90.0 °CGB13 3.2.3 Faults of the gearbox 0AM and their rectificationList of common faults 1a. – Vehicle does not run, gearbox control unit without communication. 2a. –  Uncomfortable sensation during start-up (jerking when starting up), fault in the event memory P0841 02115X or 02113 sender 1 of hydraulic pressure, gearbox - signal invalid. 3a. –  Metal noise when driving over bumps, memory without faults, SW less than 21xx. 4a. – Some gears do not shift, faults will be entered in the event memory. 5a. –  Uncomfortable sensation during start-up (jerking during acceleration, especially if going uphill or under load). 6a. –  Uncomfortable sensation during start-up or when accelerating, SW 21xx and higher, event memory without faults, clutches O.K. according to MVB. 7a. –  Uncomfortable sensation when accelerating, in 2nd gear at low speed, SW 21xx and higher, event memory without faults, clutches O.K. according to MVB. 8a. – Delayed upshifting and poor operation of the cruise control on the 1.6 TDI CR 77 kW. 9a. – Noise coming from the gearbox, 6th gear cannot be shifted, fault P073B. 10a. – The display of the gears flashes, the vehicle does not run. 11a. – The display of the gears lights up, the vehicle does not run. 12a. – The gear(s) does/do not shift. 13a. – The gears do not shift, the display of the gears flashes. Faults after replacing the components 1b. – After replacing the mechatronics, the basic setting cannot be performed, it is not possible to shift into any gears. 2b. – After replacing the clutches, the basic setting cannot be performed, it is not possible to shift into any gears, clutch is outside the tolerance. Important: The consequences of the faults on the vehicle and the diagnostic results must always be fully assessed in their context. If the focus is only on the event memory, it can result in an incorrect procedure for repairing.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�14GB 1a. The vehicle does not run, gearbox control unit without communication. Assessment: – In the event memory:  P0562 / 21148 Supply voltage for the engine too low P177F / 21065 Excessive voltage drop of hydraulic pump motor P175F / 21098 Basic setting of the gearbox not performed P189C / 21247 The diagnosis of the pressure increase cannot be carried out P174A / 21108 Valve 3 in the gearbox part, electrical fault or automatic gearbox control unit without communication – In other control units, faults in the communication with the gearbox control unit (mechatronics) Cause: It is an internal fault of the mechatronics - short circuit in the power supply part. This fault occurs on vehicles with mechatronics manufactured up to 01.06.2011. Solution: TPI 2023768 (Replacing the mechatronics, checking/replacing the fuse SB2/SB5)2a. Uncomfortable sensation during start-up. Jerking during start-up. Assessment: – SW of the control unit of the automatic gearbox 21xx, or lower. – In the event memory: P0841 02115X or 02113 sender 1 of hydraulic pressure, gearbox - signal invalid. Cause: Protected copyright. Copying for private or commercial purposes, in part or in whole, The cause of the fault is a slow oilby pressure build-up after the ignition is switched on. is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Solution: TPI 2027607 (Updating the SW of the automatic gearbox control unit using the so-called Action Code)3a. Metal noise when driving over bumps in 2nd gear. Assessment: – Metal noise at slow speed when driving over bumps – No faults are stored in the event memory – SW of the automatic gearbox control unit lower than 21xx Cause: This is caused by the excitation of oscillations when upshifting into the 3rd gear Solution: TPI 2027607 (Updating the SW of the automatic gearbox control unit to SW 21 xx and higher using the action code). The SW 21xx and higher receives the ABS signal indicating when the vehicle drives over bumps, thereby the mechatronic system disengages the 3rd gear and activates the clutch K1. Thus, damping force is applied in response to the shocks . The 3rd gear is then only shifted at the time when it is necessary. .GB15 4a. Gears are not shifted. Assessment: – Some gears are not shifted – The vehicle does not run and the display of the selector lever flashes. – In the event memory: Gear X cannot be shifted Cause: Carry out a test of the speed for the input shafts (MVB 5.3 and 5.4) at idling speed in P and N modes. The input shafts must not rotate. However, if they rotate, check the positions of the adjuster for the clutches (MVB 91 and 111), they must be a min. of 2 mm below the engagement point when in the P mode (otherwise the mechatronics is defective). If the following is entered in the event memory: P189A/21186 clutch 1 – insufficient play P073F/21086 unsuccessful synchronisation of the 1st gear P072C/21066 1st gear cannot be engaged Solution: TPI 2025571 (Replacing the clutches). This is caused by the insufficient play of clutch K1 due to the clutch engaging too early (this affects vehicles fitted with clutches manufactured in the CW 12/2009) If the input shafts do not rotate in the P mode and the following is still entered in the event memory: gear x cannot be engaged, remove the mechatronics and check the adjusters of the individual gears for mechanical damage (adjuster jammed = defective gearbox).5a. Uncomfortable sensation during start-up. Jerking during acceleration, especially if going uphill or under load). Assessment: – Jerking during acceleration or when starting up (not just a single jerk). – SW of the control unit of the automatic gearbox is 21xx, or higher – Engine running is O.K. – One fault is entered in the event memory - one of the clutches has reached the upper tolerance limit or exceeded it and is free of defects, faults Solution: TPI 2027607 If no fault is entered in the event memory, perform the basic setting and check once more the fault during the test drive. If the fault is not rectified after performing the basic setting, check the condition of the clutches according to the MVB 95-97 and 115-117. If one of the clutches has nearly reached the wear limit or is below the wear limit for transferring the max. torque, replace the clutches.6a. Uncomfortable sensation during start-up or when accelerating. Jerking. Assessment: – A single jerk (not several) when starting up or after shifting (sometimes this situation is described by the customer as a delay in the acceleration or as a short-term increase in engine speed with acceleration failure) – SW of the automatic gearbox control unit 21xx and higher – Engine running is O.K. – Condition of the clutches according to MVB 95-97 and 115-117 is O.K. – No fault is entered or faults are entered in the event memory Cause: Protected by copyright. Copying for steplessly, private or commercial in part or in whole, is not permitted If the position of the clutch adjuster cannot be changed joltspurposes, occur i.e. when starting up or unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with to the correctness of information this document. Copyright by ŠKODA AUTO A. S.� when shifting into gears; this may berespect caused by impurities in thein mechatronics leading to an erractic movement of the actuation element of the clutch. Solution: Replacing the mechatronics.16GB 7a. U  ncomfortable sensation when accelerating, jerking when accelerating slightly in the 2nd gear at low engine speed. Assessment: – Jerks/vibrations when changing gears from 1st to 2nd gear (always repeated jolts, not just a single jolt) – Jerks and vibrations at low speeds or when accelerating slightly from approx. 1200 to 2000 rpm in 2nd gear – Engine running is O.K. – Condition of the clutches according to MVB 95-97 and 115-117 is O.K. – No faults are stored in the event memory Cause: Uneven power transmission of clutch K2 (change of friction coefficient) when engaging and disengaging the clutch K2 Solution: TPI 2028367 Replacing the clutch set (using the clutch set see TPI, not according to the company ETKA).8a. Delayed upshifting and poor operation of the cruise control on the 1.6 TDI CR 77 kW. Assessment: – When driving slowly on a slope (most often in parking garages) the vehicle changes late from the 1st into the 2nd gear – WhenProtected activating the cruise control with the SET button (most often 140 km/h), the vehicle by copyright. Copying for private or commercial purposes, in part or in whole, is at not about permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee orvehicle accept any liability downshifts two gears, the cruise control remains active and the operates at high speed with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� – The fault can be detected even after replacing the mechatronics Cause: – Fault of the SW of the automatic gearbox control unit. Solution: TPI 2028079 (Updating the SW of the automatic gearbox control unit using the so-called Action Code)9a. Noise coming from the gearbox, 6th gear cannot be shifted, fault P073B. Assessment: – Noise coming from the gearbox – 6th gear cannot be shifted – After switching off and on the ignition, the gearbox is O.K. – The following is stored in the event memory: P073B – 6th gear cannot be engaged, invalid signal Cause: – Fault of the SW of the automatic gearbox control unit. Solution: Online updating of the SW of the automatic gearbox control unit (on SW 26xx, or 34xx)GB17 10a. The display of the gears flashes, the vehicle does not run. Assessment: – T he display of the gears flashes – The vehicle does not run – The following is stored in the event memory:  2 1062/21184 - P175 clutch 1 switches off inadvertently  21063/21185 – P176E clutch 2 switches off inadvertently 21094/21095 – P072C/D 1st/2nd gear cannot be shifted 21096/21097 – P073A/B 5th/6th gear cannot be shifted Cause: Fine impurities in the pressure control valves of the mechatronic control unit Solution: TPI 2027598 (Replacing the mechatronics)11a. The display of the gears lights up, the vehicle does not run. Assessment: – T he display of the gears lights up. – The vehicle does not run – The following is stored in the event memory: P072B/21073 Number of authorised attempts for changing the R gear was exceeded  P2789/10121 Path 4 of clutch 2 is too short P1899/21265 Function of clutch 2 is limited Cause: The path of the plunger for clutch K2 is too This applies toor vehicles with aor clutch Protected byshort. copyright. Copying for private commercialfitted purposes, in part in whole, is not permitted manufactured up to 25.05.2009. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Solution: TPI 2025592 (Basic setting and drive for adapting the clutch, if the fault persists, replace the clutch set).12a. Certain gears cannot be shifted. Assessment: – Initially sporadic, at a later stage the display of the gears remains lit – Noise while shifting – The vehicle does not run (initially sporadic) – T he following fault(s) is/are stored: P 173A – Transducer 1, paradoxical signal  P173B – Transducer 2, paradoxical signal P173C – Transducer 3, paradoxical signal Cause: Metal shavings on the magnets for holding the positions of the adjuster/adjusters of the gears. This applies to gearboxes manufactured up to 08.10.2008. Solution: TPI 2026829 (Replacing the gearbox).18GB 13a. Certain gears cannot be shifted, the display of the gears flashes. Assessment: – T he vehicle does not shift into another gear – The display of the gears flashes – Vibrations/jerks while driving – Sometimes the vehicle does not start – The following fault is stored in the event memory: P171BF 2127X, or 1538 – Play protection for hydraulic pump Cause: Internal fault of the mechatronics, this applies to mechatronics manufactured up to CW 45/2010. Solution: TPI 2024664 (Replacing the mechatronics)Faults after replacing the components 1b. After replacing the mechatronics, the basic setting cannot be performed. Assessment: – After replacing the mechatronics, the basic setting cannot be performed and it will be completed with a fault code – The following fault is shown in the event memory: upper limit of clutch tolerance is reached – The following fault is shown in the event memory: e.g. gear x cannot be shifted, it is not adjustable Recommendation: – Inspecting the plastic cap on the actuation element for clutches (the cap can be torn off or is lost when using an incorrect tool or during a negligent installation) – Inspecting the correct seating of the clutch adjuster. If the clutch adjuster is not located in the correct position, one of the clutches may be partially coupled, for this reason, the input shaft is engaged (check the speed according to the MVW 5.3 and 5.4) –I f the mechatronics is removed, reset the correct positions of the gear adjusters on the mechatronics (25 mm) as well as the neutral position of the actuation elements of the gears on the gearbox. Then install the mechatronics2b. Delayed upshifting and poor operation of the cruise control on the 1.6 TDI CR 77 kW. Assessment: – After replacing the clutches the basic setting cannot be performed, it will be completed with a fault code – The following fault is stored in the event memory: gear x cannot be shifted Causes and recommendations: – Preset clutch set (the clutches are coupled permanently); as a result of an impact on the clutch set when installing the complete gearbox in the vehicle (in MVB 5.3 and 5.4, the speed of the input shafts can also be detected in the position P), in this case the assembly of a new clutch set is required! – Miscalculating the washers for the clutches. If incorrect washers are used, the new clutch may be irreversibly damaged. It is necessary to perform a new measurement and calculation or to carry out the installation of a new clutch set. – Inspecting the plastic cap on the actuation element for clutches (the cap can be torn off or is lost when using an incorrect tool or during a negligent installation). Reinstall the plastic cap. – Inspecting the correct seating of the clutch adjuster. If the clutch adjuster is not located in the correct position, one of the clutches may be partially coupled, for this reason, the input shaft is engaged (check the speed according to the MVW 5.3 and 5.4). Correctly position the adjusters.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB19 3.2.4  Diagram of the recommended procedure for repairing the seven-speed gearbox 0AMThis is only valid for faults resulting from the operation. (the diagram refers neither to the faults occurring after the repair nor to the faults occuring after replacing the gearbox components).jolts, jerks, vibrationsother faultsInspecting the engine running(event memory, driving test, failures)engine O.K. fault messageengine faultGearbox diagnosis without faultChecking according to TPI* without successsolution foundengine repairBasic setting of the gearbox solution foundwithout successProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�OKOK* Checking according to TPI: Do not only check the fault but also the manufacturing period, referring to the TPI. ** MP – Compulsory registration20GB controlled fault finding without successsolution foundProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Checking according to TPI* without successTest in the controlled fault finding (Selection of functions/function components)solution foundsolution foundwithout successDISS + all information see MP* 2026333 (diagnostic protocol including MVB, checklist completed)fault eliminatedGB21 4. 4.1 Six-speed automatic transmission 02EDiagnosis of the six-speed automatic transmission 02E4.1.1 IntroductionThe following operating modes are available when carrying out the self-diagnosis of the gearbox using the diagnostic unit VAS: –C  ontrolled fault finding In the operating mode "Controlled fault finding" for automatic gearbox 02E, a test plan is available that allows the senders, actuators and the mechatronics to be checked. When inspecting the senders and the actuators, follow the instructions of the diagnostic unit VAS. –C  ontrolled functions In the operating mode "Controlled functions" of the automatic gearbox 02E, a check of the oil level must be carried out. The gearbox electronics enables the following functions:Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability – Inspecting the oil level. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� – Coding the control unit (code 20 for DSG). – Checking the gears. – Checking the shifting. – Basic setting – complete (everything is set). – Reading the measured value blocksShifting into the basic setting is carried out in accordance with: – the replacement of the engine – the replacement and the coding of the engine control unit – the replacement of the automatic gearbox control unit J217 – the removal and installation of the gearbox – the removal and installation of the electric accelerator pedal22GB 4.1.2 Measured value blocksSelected measured value blocks of the gearbox electronics serve to carry out a correct fault diagnosis on the automatic gearboxes DSG. Therefore, if a fault is detected on the automatic gearbox, a printout of all the measured value blocks must be sent (at idle speed, if the vehicle is stationary in P, N or D mode)The following information can be read in the measured value blocks (MVB): – Identification of the software and hardware level of the automatic gearbox control unit – current operating values ​​ (oil pressure values ​​ in the mechatronics, positions of the individual gear adjusters, clutch status, speeds of the individual shafts, selector lever position, etc.) – the current values recorded during the operation ​​ (journey time in the individual driving modes, operating temperatures of the clutches, journey time in all operating temperatures, warnings, etc. – specific environmental conditions when the last two faults occuredImportant measured value blocks Measured value blocks Nbr. 1.1 1.2 1.3 1.4 3.3 3.4 4.1 4.2 4.3 4.4 Description Brake light switch F Brake light switch F47 Shift lock N110 I) Vehicle speed Tiptronic shifting on steering wheel + II) Tiptronic shifting on steering wheel – II) Position of the selector lever Driving direction (G251) Output speed 1 (G195) III) Output speed 2 (G196) III) P, R, N, D, S, TT, PL, MI, RS, ER IV) Value example I) To 1.3: The signal from switch F is sufficient for activating the electromagnet N110. II)  K 3.3, 3.4: Switching over into the tiptronic mode is performed by operating one of the two rocker switches on the steering wheel (when selector lever is in position "D" or "S"). The tiptronic system is active for 8 s. The gearbox returns to the normal automatic operating mode after 8 s. If the switches on the steering wheel are activated once more, this period of time is extended. The time delay of 8 s when cornering (exceeding the value of G251 - the transversal acceleration senders), engine braking or when driving under full load, is cancelled. III)  T he gearbox control unit determines the vehicle speed and the driving direction from the signals of the senders G195 and G196. The ESP control unit uses the driving speed and the driving direction from the CAN bus drive as a replacement signal. IV)  P - Parking R - Reverse gear N - Neutral D - Drive (normal driving) S - Drive (sporty driving) TT - Tiptronic mode PL - Plus (upshift in tiptronic mode) MI - Minus (downshift in tiptronic mode) RS - intermediate position (selector lever between two stages or gears) ER - ERROR (fault)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB23 Important measured value blocks Measured value blocks Nbr. 5.2 8.1 8.2 8.3 8.4 10.1 10.2 10.3 Description Enabling the starter closed/open V) Gearbox input speed – (G182) VI) Input speed of shaft 1 – (G501 ) Input speed of shaft 2 – (G502 ) Gearbox input speed – (G195) Accelerator pedal position Kickdown switch closed/open Engine torque V)  closed - start-up enabled open - start-up disabled  he activation of the starter (terminal 50) is only performed in the selector lever position "P" or "N". T If the temperature of the gearbox oil (G93) is below -10°C, the start-up is only enabled in the selector lever position "P". At low temperatures, an increase in the driving torque occurs in the clutches. For this reason, enabling the start-up is only allowed in the position "P" (the secure grip secures the vehicle reliably). The control unit J743 transmits the signal P/N via a discrete cable (triggering the start-up of the gearbox) in the control unit J519. The information about the signal P/N is simultaneously received by the control unit J519 via the CAN data bus. The engine start-up is not enabled when there is a fault in the voltage supply for J743, E313, or of the signal P/N as well as the CAN bus. VI)  In the event of a complete signal loss of the sender G182, the switching quality deteriorates. During sporadic signal failures, a fluctuation of the speed may occur. Checking the engaged clutch with the gear shifted in P (G501, G502).Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. Š KODA AUTO A. S. does not guarantee or accept any liability Measured value blocks (in driving mode) with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Nbr. 11.1 11.2 11.3 11.4 12.1 12.2 12.3 12.4DescriptionValue range –600 ... 600 Nm 0 ... 1,53 A –327.68 ... 327.67 bar 0 ... 8160 /rpm –600 ... 600 Nm 0 ... 1,53 A –327.68 ... 327.67 bar (max. 10 bar)Speed of input shaft 1 (G501) Nominal torque of clutch K1 Current of clutch valve 1 (N215) Actual pressure of clutch 1 (G193) Speed of input shaft 2 (G502) Nominal torque of clutch K2 Current of clutch valve 2 (N216) Actual pressure of clutch 2 (G194)0 ... 8160 /rpmG501 – Speed ​​ sensor of drive shafte 1 G502 – Speed sensor ​​ of drive shafte 2 N215 – Pessure regulator valve 1 N216 – Pessure regulator valve 2 G193 – Gearbox hydraulic pressure sender 1 G194 – Gearbox hydraulic pressure sender 224GB Measured value blocks Nbr. 16.1 16.2 16.3 16.4 19.1 19.2 19.3 Description Path of adjuster for gears 1-3 (G487) VII) Path of adjuster for gears 2-4 (G488) VII) Path of adjuster for gears 5-N (G489) VII) Path of adjuster for gears 6-R (G490) VII) Temperature of gearbox oil (G93) Standard VIII) Temperature in the control unit (G510) IX) Oil temperature of multi-plate clutch (G509) X) VII)  approx. 8 mm – Adjuster is correctly set VIII)  T he sender G93 transmits more accurate values ​​ than the sender G510. IX)  T he sender G510 serves mainly for checking the validity of the signal of sender G93. X)  At a temperature (G93) higher than 138°C, the mechatronic control unit J743 triggers a reduction in engine torque. Up to a temperature of 145°C, a progressive reduction in engine torque occurs until the engine runs only at idle speed. The multi-plate clutches are then uncoupled, the vehicle is no longer powered.Measured value blocks Nbr. 20.1 20.2 20.3 54.1 64.1 64.2 80 81 82 84 Description Desired gear Currently engaged gear Information about the engaged gear in the instrument panel Identification of the mechatronics Number of values exceeded (170 °C) XI) Number of warnings (160 °C) XI) Identification of the control unit Identification of the control unit Identification of the control unit Manufacturing date of the gearbox and gearbox code. XI)  Value of sender G509 - sensor for oil temperature in the multi-plate clutch. When reaching an oil temperature of 160°C, the safety function is then activated and the clutches pulsate, which is perceived in the vehicle as a strong jerk (warning jerk). When reaching 170 °C, the clutches disengage. Sporadic signal failures can result in harsh shifting or skipping gears. As of MY 2013, the sender G509 is no longer present and the temperature is recalculated.Measured value blocks – Temperature of the gearbox oil Nbr. 109.1 140.1 140.2 140.3 140.4 141.1 141.2 141.3 Description Total mileage travelled in kilometres Oil temperature 90°C Oil temperature =90°C – 110°CProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Oil temperature =110°C – 120°C Oil temperature =120°C – 130°C Oil temperature =130°C – 140°C Oil temperature =140°C Maximum temperature value is reachedThe time intervals, during which the oil temperature moves within the specific temperature ranges, are recorded in the blocks 140.x.GB25 Printout of the environmental conditions for the last two faults stored in the event memory All collision values ​​ from the measured value blocks are stored in the fault memory. The printout of the environmental conditions is also stored for the last as well as the second last recorded faults. An example of a printout for the environmental conditions from the fault memory is provided below. Printout of the environmental conditions when the last fault was recorded:90_1 S1 Fault ID 90_2 S1 clutch 90_3 S1 accelerator pedal 90_4 S1 selector lever position 91_1 S1 G182 - input speed of the gearbox 91_2 S1 G501 - speed of ​​ drive shaft 1 91_3 S1 G502 - speed of ​​ drive shaft 2 91_4 S1 G195/196 - gearbox output speed 342 3 0.0 % 87 640/rpm 0/rpm 0/rpm 0/rpm 92_1 S1 actuation elements of the gears 1-3 480 92_2 S1 actuation elements of the gears 2-4 248 92_3 S1 actuation elements of the gears 5-N 480 92_4 S1 actuation elements of the gears 6-R 416 93_1 S1 N215 - current of valve for clutch 1 0.00 A 93_2 S1 N216 - current of valve for clutch 2 0.00 A 93_3 S1 N217 - current of valve for main pressure 3 0.006 A 93_4 S1 G510 - temperature sender in control unit 91 °C 104_1 S1 Actuating the actuation element of the gears, special conditions 0x0000 104_2 S1 different gears 0x0027 104_3 S1 battery voltage 13.0 V 104_4 S1 engine torque 14 Nm 105_1 S1 clutch pressure K1 0.10 bar 105_2 S1 lower point of current for adapting K1 0.210 A 105_3 S1 clutch pressure K2 0.10 bar 105_4 S1 lower point of current for adapting K2 0.215 A 110_1 S1 mileage in km 85880 kmPrintout of the environmental conditions when the second last fault was recorded:94_1 S2 Fault ID 94_2 S2 clutch 94_3 S2 accelerator pedal 94_4 S2 position of the selector lever 95_1 S2 G182 - gearbox input speed 95_2 S2 G501 - speed of ​​ drive shaft 1 95_3 S2 G502 - speed of ​​ drive shaft 2 95_4 S2 G195/196 - gearbox output speed 65535 0 0.0 % 0 0/rpm 0/rpm 0/rpm 0/rpm 96_1 S2 actuation elements of the gears 1-3 0 96_2 S2 actuation elements of the gears 2-4 0 96_3 S2 actuation elements of the gears 5-N 0 96_4 S2 actuation elements of the gears 6-R 0 97_1 S2 N215 - current of valve for clutch 1 0.0 A 97_2 S2 N216 - current of valve for clutch 2 0.0 A 97_3 S2 N217 - current of valve for main pressure 3 0.0 A 97_4 S2 G510 - temperature sender in control unit 60 °C 106_1 S2 Actuating the actuation element of the gears, special conditions 0x0000 106_2 S2 different gears 0x0000 106_3 S2 battery voltage 0.0 V 106_4 S2 engine torque 98 Nm 107_1 S2 clutch pressure K1 0.00 bar 107_2 S2 lower point of current for adapting K1 0.000 A 107_3 S2 clutch pressure K2 0.00 bar 107_4 S2 lower point of current for adapting K2 0.000 A 111_1 S2 mileage in km 0 kmProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�26GB 4.1.3 Faults of the gearbox 02E and their rectificationList of common faults 1a. – Uncomfortable sensation when shifting gears (Octavia II, Superb II) 2a. – Paradoxical shifting 3a. – Malfunction of the shifting 4a. – Failure of the power transmission to the wheels 5a. – Incorrect downshifting of the gearbox 6a. – Delayed accelerationImportant: The consequences of the faults on the vehicle and the diagnostic results must always be fully assessed in their context. If the focus is only on the event memory, it can result in an incorrect procedure for repairing.1a. Uncomfortable sensation when shifting gears (Octavia II, Superb II) Assessment: – While driving or when shifting the individual gears, uncomfortable shifting, jerking, jolting, etc. occur. – In most cases no fault is stored in the event memory of the gearbox control unit. Cause: This is an internal fault of the mechatronic gearbox control unit. Solution: – Checking the manufacturing date of the mechatronics. Test procedure: Self-diagnosis, 02 - Gearbox 011 - Measured value block - channel 54 H07 A0001 - J21 N0560 H = Year 2007; 07 = Calendar week J = Year 2008; 21 = Calendar week TPI 2022347 issued Determine if the manufacturing date falls in the previous time period ( H07 – J21), if so replace the mechatronics. After replacing it, perform the basic setting and carry out a test drive.2a. Paradoxical switch-over. Assessment: – If the speed is reduced abruptly when braking (e.g. from 130 km/h to 80 km/h) the automatic gearbox shifts down into third or second gear when in the operating mode D or S. At this moment, the engine speed increases and will remain above 3000 rpm for a few seconds. A similar phenomenon may also occur when braking, while rolling to an intersection, if the gearbox downshifts into first gear and the engine speed temporarily increases. Solution: TPI 2025846 issued On vehicles with ESP control unit with the index ... 379A replace the sender G419 (without G251) with the sender G419 (with G251).Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB27 3a. Malfunction of the shifting. Assessment: – malfunction of the automatic gearbox – the display of the engaged gears disappears sporadically in the Maxi-Dot – the engaged gear cannot be changed – jerks can be felt when in operating mode "D" – after shifting into "R", the vehicle does not drive – the fault 19143 004 is stored in the fault memory of the gearbox; P2711 - Gearbox control unit without signal/ communication stored Solution: TPI 2024152 issued Replacing the clutch set4a. Failure of the power transmission to the wheels. Assessment: – T he gearbox control unit detects an incorrect clutch temperature and evaluates it as a clutch overload. Consequently, the safety function of the clutch is activated (the display showing the shifting flashes, the vehicle jerks, the engine torque drops and the clutch switches off). Solution: Maintenance intervention 37F2 Updating the SW of the gearbox control unit5a. Incorrect downshifting of the gearbox. Assessment: – Vehicle model:  Octavia II MY 2007-2009, Superb II MY 2008-2009 – When gear D4 is engaged (1500-2500 rpm), and the cruise control is activated, the gearbox shifts down into D2 (4000 rpm). – After switching off the cruise control, the gearbox shifts back into D4. Solution: Updating online and via diagnostic address 02Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�28GB 6a. Delayed acceleration. Assessment: – Vehicle model: Octavia II MY 2006–2011, Superb II MY 2008–2011, Yeti MY 2009–2011 – After deceleration (e.g. when rolling to an intersection) and subsequent acceleration, the engine speed increases and the vehicle drives off with delay. – When shifting manually into tiptronic mode (3-2, 4-3 or 5-4), the engine speed increases and the vehicle reacts again with delay. Solution: Updating online and via the engagement code (see table). Table of engagement codes Vehicle model Octavia II Octavia II China Superb II Yeti Yeti RUS Engagement code 308A 308B 308C 308D 3091Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB29 4.1.4  Diagram of the recommended procedure for repairing the six-speed gearbox 02EThis is only valid for faults resulting from the operation. (the diagram refers neither to the faults occurring after the repair nor to the faults occuring after replacing the gearbox components).jolts, jerks, vibrationsother faultsInspecting the engine running(event memory, driving test, failures)engine O.K. fault messageengine faultGearbox diagnosis without faultChecking according to TPI* without successProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�solution foundimpurities in the oil (photo DISS)impurities in the oil oil O.K.engine repairBasic setting of the gearbox solution foundwithout successOKOK* Checking according to TPI: Do not only check the fault but also the manufacturing period, referring to the TPI. ** MP – Compulsory registration30GB controlled fault finding without successsolution foundProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Checking according to TPI* without successsolution foundTest in the controlled fault finding (Selection of the functions/the functional components)solution foundwithout successDISS + all information see MP* 2026333 (diagnostic protocol including MVB, checklist completed)fault eliminatedGB31 5. Technical request for repairing the gearboxes 0AM or 02EThis procedure applies to all the complaints concerning the automatic gearbox DSG. – 0AM (DQ200) seven gears – 02E (DQ250) six gears The conditions under which the alleged fault occurs, are often specified inaccurately when describing the faults of the automatic gearbox in the DISS system. For this reason, the time for handling the complaint is extended, and vice versa, the time required for resolving the fault is shortened greatly by sending the complete documents. When creating a "DISS - technical request for repair" the following must always be included: – Complete "Checklist of the fault description for DSG gearboxes" – Diagnostic protocol online – Complete measured value blocks – Description of complaints by the customer – Service entries – List of operations that have been carried out on the gearbox before sending the technical requestProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�32GB Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB33 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�34GB Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB35 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�36GB NotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� NotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� NotesProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Overview of the previously edited workshop teaching aidsNo. Designation 52  ŠkodaFabia; 1.4 ltr. TDI engine with unit injection system 1 Mono-Motronic 53 ŠkodaOctavia; Vehicle presentation 2 Central locking 54 ŠkodaOctavia; Electrical components 3 Vehicle alarm 55 FSI petrol engines; 2.0 ltr./110 kW and 1.6 ltr./85 kW 4 Working with wiring diagrams 56 Automatic gearbox DSG-02E 5 ŠKODA FELICIA 57 Diesel engine; 2.0 ltr./103 kW TDI with pump-nozzle units, 6 Safety of the ŠKODA vehicles 7 Principles of ABS - were not published 2.0 ltr./100 kW TDI with pump-nozzle units 8 ABS - FELICIA 58  ŠkodaOctavia, Chassis and electromechanical 9 System for safe start-up with transponder pow