TECHNICAL DOCUMENTATION

SSP 096 ŠKODA Octavia III Presentation of the vehicle Part I

PDFEN60 pages5 MB
SSP 096 ŠKODA Octavia III Presentation of the vehicle Part I - PDF cover

This PDF is currently unavailable.

Read document text
Presentation of the vehicle Part IŠKODA Octavia IIIProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Self-study programmeŠKODA Service®96 The first Octavia was manufactured in the Mlada Boleslav car factory in 1959 as the eighth model in the model series – which its name Octavia was derived from. As compared with its predecessor, ŠKODA 440 (familiarly referred to as Spartak), the first Octavia had a modified front body grill and modernized front axle. Leaf springs were substituted with coiled springs with telescopic absorbers. It was a reliable and easily controllable car. Thus, Octavia celebrated success on the domestic market as well as abroad and it was assembled overseas as well.Contemporary poster with the historical predecessor of the new ŠKODA Octavia III(Source: Archive of the companyŠKODA AUTO)SP95_08Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� Table of Contents Part ILook Back into History ������������������������������������������������������������������� 2 1. Introduction ������������������������������������������������������������������������ 5 1Introduction of the Vehicle������������������������������������������������������������� 5 2. MQB Architecture �������������������������������������������������������������������� 6 2.1 MQB Architecture and New ŠKODA Octavia III���������������������������������������������� 6 2.2 Modular System Across All Vehicle Classes������������������������������������������������ 6 2.3 MQB in Development and Design of New Vehicles������������������������������������������ 7 2.4 MQB in Production����������������������������������������������������������������� 7 2.5 MQB and Vehicle Weight Reduction����������������������������������������������������� 8 2.6 MQB and Module Groups������������������������������������������������������������� 8 3. Body Design and External Vehicle Elements ������������������������������������������������ 9 3.1 Family Design Lines of ŠKODA AUTO����������������������������������������������������� 9 3.2 General View of the Design of ŠKODA Octavia III������������������������������������������� 10 3.3 Mirrors with Integrated Direction Indicators and ELAB Function�������������������������������� 12 3.4 Panoramic, Electrically Controlled Sunroof ���������������������������������������������� 14 3.5 Concept of Storage Spaces in Vehicle Interiors ������������������������������������������� 16 3.6 Boot ������������������������������������������������������������������������� 20 3.7 Clever Solutions ����������������������������������������������������������������� 22 4. Vehicle Dimensions ������������������������������������������������������������������ 23 4.1 Vehicle Outer and Inner Dimensions ��������������������������������������������������� 23 4.2 Weights and Volumes ������������������������������������������������������������� 25 5. Body ����������������������������������������������������������������������������� 26 5.1 Body Frame ��������������������������������������������������������������������� 26 5.2 Design of MQB Floor Group ��������������������������������������������������������� 27 5.3 Progressively Deformable Front Part of Vehicle������������������������������������������� 29 5.4 Active Engine Cover Hinges ��������������������������������������������������������� 32 6. Chassis ��������������������������������������������������������������������������� 34 6.1 Chassis types ������������������������������������������������������������������� 34 6.2 Front McPherson Axle ������������������������������������������������������������ 36 6.4 Rear Trailing Axle ���������������������������������������������������������������� 37 6.3 Rear Multi-Element Axle ����������������������������������������������������������� 38 7. Brake System ���������������������������������������������������������������������� 40 7.1 Variants of Control Units for Brake and Stabilization Systems �������������������������������� 42 7.2 Multi-Collision Braking Function ����������������������������������������������������� 44 7.3 Prefill Function (EBP) �������������������������������������������������������������� 45 8. Wheels and Discs ������������������������������������������������������������������� 46 9. Engines ��������������������������������������������������������������������������� 47 9.1 New MOB and MDB Engines ��������������������������������������������������������� 47 9.2 Tabular Summary of Motorizations ��������������������������������������������������� 49 9.3 1.2 TSI / 63 kW and 77kW Gasoline Power Units ������������������������������������������ 50 9.4 1.4 TSI / 103 kW Gasoline Power Unit �������������������������������������������������� 51 9.5 1.8 TSI / 132 kW Gasoline Power Unit �������������������������������������������������� 52 Protected byUnits copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 9.6 1.6 TDI / 77 kW Diesel Power ��������������������������������������������������� 53 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability respect to the ���������������������������������������������������� correctness of information in this document. Copyright by ŠKODA AUTO A. S.� 9.7 2.0 TDI / 110 kW Dieselwith Power Unit 54 10. Gearboxes ������������������������������������������������������������������������ 55 10.1 Overview of Gearboxes for Gasoline Power Units ���������������������������������������� 55 10.2 Overview of Gearboxes for Diesel Power Units ������������������������������������������ 56 10.3 S  ailing Mode Functions in Automatic Gearboxes ����������������������������������������� 57GB3 SP96_45The official initiation of the series manufacture of the new ŠKODA Octavia III model took place in December 17, 2012, in the ŠKODA AUTO factory, Mlada Boleslav.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�You will find the instructions for assembly and disassembly, repairs, for diagnostics plus detailed user information in the VAS diagnostic instruments and in the on-board literature. Editorial closing date was in 12/2012. This Book is not subject to updating.SP95_004GB 1. Introduction1.1 Introduction of the VehicleŠKODA Octavia III is the third generation of the hitherto most popular model produced in ŠKODA AUTO. Completely new vehicle comes with this model. It is a newly introduced structural concept of MQB (see page 6 to 8 of this Book) that has a great influence on the general Octavia metamorphosis. The line of oncoming design was already introduced with ŠKODA Rapid car but onlooker still holds his/her breath when looking at the new Octavia visage. The design is accentuated but it also promises ageless sight. The robustness of limousine, ample equipment, vehicle safety, large inner space and boot, all of this provides Octavia III with a momentum to rival the cars of not only the comparable but even the higher classes of competitor makes. Octavia III is driven by a wide choice of modernized gasoline and Diesel engines. Aside from the manual gearboxes, the outfits also contain the automatic gearboxes, even the 4x4 drive with attached rear axle drive via Haldex clutch will not be missing. It is also the RS, Scout and, last but not least, Combi version that is being prepared for customers.SP96_14Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB5 2. MQB Architecture2.1 MQB Architecture and New ŠKODA Octavia IIIGeneration 3 ŠKODA Octavia is the first car in the history of ŠKODA AUTO that is designed in the new MQB system. The very first car with this architecture was A3 car from Audi to be followed by Golf 7 from Volkswagen. With Octavia III the Mlada Boleslav car factory takes its part in the manufacture of the cars with a modern MQB concept.SP99_01MQB chassis2.2 Modular System Across All Vehicle ClassesMQB architecture (the abbreviation of German "Modularer QuerBaukasten") represents the Group's modular kit system that was designed for the cars with a transverse engine mounting. MQB architecture is a modern strategy that leads to more efficient routing of the development toward identical modules that can be implemented into most of the cars manufactured in the Volkswagen Group. The new system leads to the reduced number of manufactured components and thereby to the reduction of the costs for development and production.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�6GB 2.3 MQB in Development and Design of New VehiclesIn designing the ŠKODA Rapid, ŠKODA Roomster, ŠKODA Yeti cars, the modular system was applied already, however, designers were still bound by the chassis platform. With MQB architecture, even the chassis becomes fully modular. The same elements will thus form the chassis of most of the cars. As a result, the chassis platform system will cease to exist. Paradoxically, the extended unification will bring higher freedom for the designers in designing new cars. The MQB chassis architecture is bound by the only fixed dimension in the area: the front axle - steering. The width in this part of the car is already variable as all the other chassis dimensions.variableSP96_02variableuniformvariablevariable2.4 MQB in ProductionThe use of uniform structural units in all the Volkswagen Group makes is followed by the application of standardized assembly procedures and identical assembly equipment. With complete introduction of MQB, a uniform, all-Group body of the assembly fixtures, jigs and tools will be formed in the area of production. In future, it will therefore be possible to adapt the assembly line in flexible manner to the production of different car with MQB Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted architecture than the car primarily made on this line. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB7 2.5 MQB and Vehicle Weight ReductionWhile designing the structural units of MQB emphasis is put on the reduction of weight. This applies not only to the weight reduction of engines and gearboxes, car body in the area of floor, axles but also to the metal elements of seats, supporting part for the dashboard, weight savings were also found in the reworked lines of the wiring harnesses. Emphasis on the reduction of weight in new cars is put namely in terms of economy and ecology where simple formula applies: lighter car = lower fuel consumption = lower emissions.SP96_102.6 MQB and Module GroupsWe can divide MQB architecture into several groups. Unification in each of these basic module families will result in significant reduction in structural units throughout the Group. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted – Chassis: Uniform chassis structural units. in this document. Copyright by ŠKODA AUTO A. S.� with respect to the correctness of informationunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability–D  rive-axle assemblies: Uniform drive-axle assemblies throughout all the Group cars. The gasoline and Diesel engines have retained the same performance parameters of the current drive units but the new MOB (gasoline) engines and MDB (Diesel) engines are structurally redesigned. All the power units are inclined back by 12° and the exhaust standpipes in all of them are led out back as well. MQB architecture will also pertain to the alternative drives (LPG, CNG and electric drive). – Electronics:  Sharing of identical assistance systems, driving dynamics systems, MIB – (Modularer Infotainment Baukasten) modular system of radios, navigation systems, and other multimedia devices.8GB 3. Body Design and External Vehicle Elements3.1 Family Design Lines of ŠKODA AUTOOne of the points of the new design conception is also creation of unific elements for all the new ŠKODA AUTO cars so that their pertinence to the same car family is apparent unambiguously. Once the ŠKODA Rapid model was introduced, also the shape of new Octavia III's body adheres to the basic unific design lines. The engine compartment cover is shaped with four profiled mouldings while the fresh logo of the car company is placed between the two middle profiled mouldings on the body's face. The inner profiled mouldings then follow the design of the centre panel in the car interiors. The outer profiled mouldings of engine cover go to A-pillars to continue over the roof to the car's tail end. Further hereditary elements of the new ŠKODA cars, including the new Octavia, is the "clover-leaf" arrangement of front headlamps and fog lamps as well as the radiator grill with ornamental border.SP96_11Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB9 3.2 General View of the Design of ŠKODA Octavia IIINew ŠKODA Octavia has numerous elements that make a real robust limousine out of it. One of the unmistakeable identification signs of the new model from ŠKODA AUTO family is the design of the rear side doors.Radiator grill ribbing combines a glossy face with matt sides of individual plates.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�mirrors with integrated direction indicatorsThe front adaptive Xenon headlamps, on request with LED technologya dominant line of profiled mouldings that follows the radiator grill new series of the design cast wheels, see page 46 of this Bookfog headlamps with Corner function10GB plastic caps in the point of B-pillar are part of the new Octavia's door as opposed to the ŠKODA Rapid modelthe transition between rear window and door body is formed by a dynamic curve that rises to C-pillarthe car is garnished with the massive door handlesSP95_05designation of the car company with a wording ŠKODAdesignation of the model with a wording OctaviaSP96_06sharp marked profiled moulding in the bottom part of doorsrear light combinations in a shape of double letter C, on request with LED technologyReflecting glasses in the rear bumper areaGBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�11 3.3  Mirrors with Integrated Direction Indicators and ELAB Function (elektrisch abklappbar)Direction indicator is integrated in the mirror cover. LED diode is used as a light source. The external mirror side from the driver's view is fitted with a light conductor. The driver is thus visually informed of active direction indicator when he/she looks in the mirror.direction indicator's light conductorSP96_09AAutomatic mirror tilting - ELAB The external rear-view mirrors are equipped with the automatic electric tilting function. Driver uses remote control to place the mirrors to the parking position (by tilting the mirrors down). The mirrors are lifted off to the driving position once the car is unlocked, door opened and ignition turned on. The mirrors can also be tilted down using the control on the inner side of door. If the mirrors are tilted manually using the control on the door they can be lifted off using the same control only.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability If the mirrors are tilted via the "Comfort tilting" function remote control)in their lift-offCopyright using the control with respect to(using the correctness of information this document. by ŠKODA AUTO A. S.� on the door can be avoided – by putting the joystick to the tilting position before ignition is tuned on.The automatic mirror tilt function is controlled by BCM unit.12GB Auto-fading glass of external mirrors The auto-fading, electrochromic glass of external mirrors is activated together with the inner mirror. The sensors of the interior mirror scan the intensity of light coming from the car front and tail end. If the intensity of the light coming from behind is higher, the auto-fading glass of all the three mirrors is activated. Driver can deactivate the auto-fading system using the button on the inner mirror¨s bottom side. External mirror heating External mirrors are heated. Heating can be turned on within the maximum outer temperature of +35°C. Mirror incline and Memory function Mirror incline is connected with the functionality of the driver's memory seat. Mirror positions are stored to the memory along with the seat position.SP96_09BSP96_09CExit area illumination External mirrors in the highest outfit are also supplemented with integrated light in the bottom part of mirror's cover. This light goes on when relevant door is opened so that the outer space in immediate vicinity of the door is illuminated. Both driver and front passenger then can get off into illuminated area with higher comfort, ergonomy and safety.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP96_75GB13 3.4 Panoramic, Electrically Controlled SunroofPanoramic sunroof of ŠKODA Octavia III is equipped with electrical control. The panoramic sunroof glass is tinted having a lower light transmission and heat permeability. Panoramic sunroof can be opened in two modes: – tilt back – backward shifting Panoramic sunroof is equipped with a wind deflector that limits noise propagation and direct flow of air into the interiors in the sunroof backward shifting mode. Sunroof can be covered with a window blind from inside of the car.SP96_34Panoramic sunroof in the tilt-back modeParameters of the panoramic sunroof Heat permeability Light transmission sunroof width sunroof length control blindProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�8.2 % 9.9 % 981 mm 821 mm combined rotary switch manual14GB Panoramic sunroof in the backward shifting mode wind deflectorSP96_33mesh blindProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability switch with respect to the correctness of information in this document. combined Copyright by Šrotary KODA AUTO A. S.�SP96_38The panoramic sunroof control system is located in the ceiling module. Panoramic sunroof is controlled using the rotary combined control that has eight preselected window positions. When in zero position it has the button function - when pressed, the sunroof tilts back. Mesh blind can be used to cover the window completely, the mesh blind is operated manually, the pulled-out position is independent of the panoramic sunroof movement.GB15 3.5 Concept of Storage Spaces in Vehicle InteriorsInterior of ŠKODA Octavia III model offers large set of practical storage spaces and compartments.tip-out storage box in the dashboard on passenger side (4)ceiling console with a storage compartment for glasses (1)storage box on the left under the steering wheel (8)storage box in front of the gear lever (2) storage pockets in the front side doors (3)unless authorised ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or acceptpockets any liability storage warning vest holder by under with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� in the rear side the driver seat (7) doors (12)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitteddrink holder on the centre console in the front (9)16GB storage "Jumbo Box" under the adjustable elbow rest (6)tip-out storage box under passenger seat (5)tip-out box on the centre console back under the "Jumbo Box" (13) storage pockets on the rear side of the front seat backs (11)drink holder integrated in the rear folding elbow rest (10)multifunction box under the rear plateau (14)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�side pockets in the boot (15)SP96_17GB17 (1)SP96_83(2)SP96_84(3)SP96_85(4)SP96_86(5)SP96_87(6)SP96_88Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�(7)SP96_89(8)SP96_9018GB (9)SP96_91(10)SP96_92(11)SP96_93(12)SP96_94(13)SP96_95(14, 15)SP96_72Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB19 3.6 BootThe basic volume of the boot, including the stowage bay under the floor amounts to 590 litres. Once the rear seats are tilted, the boot can be enlarged up to 1580 litres. Plateau and multi-function box can also be removed for the boot to be utilized up to the car's ceiling cushioning. The boot is fitted with side pockets with cargo elements used to hold luggage (see page 22), double-faced carpet, multi-function box - removable storage box under the rear plateau, 12V socket, lantern, and lash eyes.the rear plateau is lifted together with the boot lidextendable multi-function box fitted with a pair of shifting compartmentsSP96_35dual retractable hooklash eye the surface of the boot's floor and walls is covered with a textile carpet 12V socketProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�20GB face of the double-faced carpet - the side with textile carpet side pocket's sideboard with Cargo elements see page 22back of the double-faced carpet - the side with washable surfacestrap to fasten the first-aid kit control lever to tilt back the rear seats from the bootSP96_41SP96_39Protected by copyright. for private or commercial purposes, in part or The in whole, is not permitted On request, the bootCopying floor can be equipped with rear seats in the new Octavia III can be comfortaunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability double-faced carpet. Textile carpet from one side, bly tilted down directly from the boot using relevant with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� easily washable surface from the other side. control levers.SP96_42SP96_40We can find a full-bodied reserve wheel under the boot floor or this space can be divided with compartments and utilized as a place for the tool kit with additional stowage space.GB21 3.7 Clever SolutionsThe ŠKODA Octavia III is equipped with the following set of clever solutions that contribute to the user's comfort: – warning vest holder under the driver seat – ice scraper on the fuel tank neck cover – waste bin in the door bolstering (Fig. SP96_73) – double-faced carpet in the boot – holder for multimedia instruments (Fig. SP96_74) It is for the first time that the clever solutions below were presented with Octavia III: Cargo elements Cargo elements represent the plastic elements fitted with Velcro fastener through which they are fastened to the boot floor. The plastic elements can be used to easily fix positions of the articles stored into the boot so that their undesirable motion on the run is prevented (Fig. SP96_69). In case you are not using the Cargo elements they can be stored into prepared positions in the compartment walls behind the rear wheel arches (Fig. SP96_68).Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP96_69SP96_73SP96_68SP96_74Multi-function box under the rear plateau Multi-function box represents removable storage box that can be divided into three separate sections by using two adjustable partitions.22GB 4. Vehicle Dimensions4.1 Vehicle Outer and Inner Dimensions2686 mm * 4659 mm1461 mm699 mm1549 mm * 1814 mmProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�1520 mm ** The specified dimensions are valid for the motorization of 1.2 TSI/63 kW and 15" wheels.GB23 Outer vehicle dimensions Length Width Width with mirrors Height Height (with a packet for bad roads) Height (with Sport packet) Wheel base Wheel base (for 1.8 l/132 kW TSI motorization) Clearance height Clearance height (with a packet for bad roads) Clearance height (with Sport packet) Loading sill height (with unladen weight) Front wheel tread Rear wheel tread 4659 mm 1814 mm 2017 mm 1461 mm 1476 mm 1446 mm 2686 mm 2680 mm 140 mm 155 mm 125 mm 699 mm 1549 mm 1520 mmOuter vehicle dimensions for the 1.2 l/63 kW TSI and 1.6 l/77 kW TDI motorizations + 15" wheels for the 1.4 l/103 kW TSI and 2.0 l/110 kW TDI motorizations + 16" wheels for 1.8 l/132 kW TSI motorizations + 16" wheelsFront wheel tread 1549 mm 1543 mm 1543 mmRear wheel tread 1520 mm 1514 mm 1512 mmVehicle inner dimensions Width in ells on the front seats Width in ells on the rear seats Effective area for the head in front Effective area for the head in rear Boot volume The boot volume with the rear backrests tilted back 1454 mm 1449 mm 983 mm 980 mm 590 l 1580 l24Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB 4.2 Weights and VolumesWeight and volume table Unladen weight* Effective load* Total weight Maximum rooftop load Maximum weight of unbraked towed vehicle Maximum weight of braked towed vehicle Maximum vertical load of trailer coupling Fuel tank capacity 1225 kg 625 1775 kg 75 kg 610 kg 1300 kg 75 kg 50 lThe values in table apply for the 1.2 TSI/63 kW motorization. * This applies for the car with basic outfit, what is included then is the driver's weight of 75 kg.Boot parameters Boot volume (up to the height of covering plateau) The boot volume with the rear backrests tilted back Length 590 l 1580 l 1084 mmunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilityWidth (between wheel arches) 1010 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is notmm permitted Height (to the covering plateau) 545 mm with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP96_71SP96_70GB25 5. Body5.1 Body FrameThe required body strength is attained by using the strength steels in the key locations of both the body hood and the car floor part. Everything is steered toward the maximum measures in providing protection of the inner space for passengers. Application of the strength steels brought weight reduction. The high-strength steel in new Octavia III is used for the manufacture of A-pillars and B-pillars, front bumper's cross beam, and robust MQB frame of the floor with centre tunnel.Hot forming of steel componentsSP96_37Octavia I (0 %)Octavia II (6.3 %)Octavia III (26.1 %)Figure depicts (throughout three Octavia models) introduction of the hotforming technology of steel sheets, the aim to apply hardened steel parts is clearly apparent here – firm A-pillars and B-pillars for the maximum protection of the crew. Owing to the optimized body structure, the static rigidity of Octavia III model increased by about 25 % as compared with its predecessor, Octavia II.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The specially designed engine cover structure allows easy deformability of the part and, together with the active hinges, it forms a modern element of passive safety to protect pedestrians (see page 29)26GB Depending on the yield point the steel is classified into several groups. 200 MPa 220–420  MPa 700–850  MPa 1000–1200  MPa 31.26 % 45.60 % 2.5 % 20.64 %The firm A-pillars and B-pillars protect the crew against lateral and frontal impactsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP96_36The purportedly deformable areas of the front bumper's beam allow for controlled distortion of the car's front end (see page 28)The car doors are braced with both diagonal and horizontal strength plates to protect the car crew under the lateral crashesGB27 5.2 Design of MQB Floor GroupThe ŠKODA Octavia III floor is formed in MQB architecture, the grey coloured part of the Figure depicts the floor parts that are modular for the entire Group family. The resultant floor of each car with MQB architecture can have absolutely different parameters but the weldment will still be composed of module plates of one all-Group kit. The unique parts for New Octavia model are indicated in green.MQB architecture Octavia model onlyProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP96_1328GB 5.3 Progressively Deformable Front Part of VehicleWhat is mounted below the front bumper of ŠKODA Octavia III are the following structural elements of the car's passive safety: – cross beam to protect pedestrians – foam component to protect pedestrians – front bumper's beamfoam component to protect pedestrianscross beam to protect pedestriansProtected by copyright. Copying for private or commercial purposes, in part or in whole, is notbumper's permitted front unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�program-deformable area of the beamfront bumper's beam front wall moduleSP96_31front bumper with radiator grillBumper's structure is conceived in such a manner that the damages caused to the important components in the car's front end by the impacts at low speeds are as least as possible. Just the same as in ŠKODA Rapid, the radiator grill is firmly connected with bumper. It is no longer attached to the cover of engine part as was the case in the previous models.GB29 Front bumper's beam The front bumper's beam includes the program-deformable elements that will absorb a large amount of kinetic energy induced during the crashes at low speeds (up to 15 km/hr). Thus, they efficiently reduce the risk of damage to the engine part and the supporting body structure. In the crashes at high speeds, the bumper's beam jointly participates in convenient initiation of the deformation of front runners which are programmed so that they, at the same time with further body structure, absorb the crash energy minimizing by doing so the crew injury hazard.program-deformable areas of the front bumper's beamSP96_32front bumper's beamCross beam and foam component to protect pedestriansProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The pedestrian protection crossrail and the pedestrian protection foam component are designed to minimize injury of the pedestrian's legs when being hit by a car. The main pursued criteria are the deceleration of pedestrian leg's movement, the bend angle in a knee joint, and the shear in a knee joint. The entire system is debugged upon calculations and tests so that the values of the criteria above are as low as possible.30GB 5.4 Active Engine Cover HingesWithin the pedestrian protection measures the ŠKODA Octavia III car is equipped with active hinges of engine cover. Function description The three sensors located on the car's front end will recognize crash, the airbag control unit these sensors are connected to will fire the actuators' pyrotechnics, then these actuators lift up the rear engine cover hinges, this will cause the cover's rear edge to be extended up by 55 mm to be locked in the target position. As a result, an empty space is formed between the engine cover and the actual power unit and this empty space allows possible deformation of the cover towards the engine part. In case of a crash, the pedestrian's body encounters the lifted engine cover and the kinetic energy is attenuated by the deformation of the cover plates. The active engine cover reduces consequences of the possible crash between car and pedestrian being therefore significant, modern element of the passive safety.Function of hinges in the basic position The active engine cover hinge is composed of three arms. If actuators are not activated the additional arm R3 and the upper arm R2 are connected with a rivet and the entire hinge acts as a double-arm hinge with one functional pivot till the moment of activation.upper arm R2N rivet that is used to connect additional arm R3 and upper arm R2 (until activation takes place) additional arm R3lower arm R1Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. SP96_04 S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� actuatormovement of pivot is locked with N rivetThe span of speeds as the condition for system activation The pyrotechnic hinge actuators will be activated by the airbag control unit only at the car speeds from 30 to 55 km/hr.Further conditions for the correct system functioning Car's registration plate must be mounted directly to the car's bumper. The registration plate's holder influences negatively the pedestrian protection system sensors (active bonnet) and thereby the entire system's functionality.GB31 Bonnet hinges after the system activation The gas from pyro-cartridge extends the actuator's piston upwards, this force will shear the rivet (see the hole after rivet N3 and N2) that connected the hinge arms R1 and R2. The opening angle between the R1 and R2 arms is locked by the cam with spring.knuckle joint of the upper arm R2 and lower arm R1N3 hole after the sheared rivet in the additional arm R3 N2 hole after the sheared rivet in the upper arm R2pin with springlocking camlower arm R1 of the cover hingeknuckle joint of the additional arm R3 and upper arm R2SP96_03lock pin extended piston of actuatoractuatorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Car transport after the system activation If the car is not damaged in any other way it is possible to go carefully to the nearest repair shop with the activated bonnet. Vehicle speed with activated engine cover must not exceed 80 km/hr. Repair of hinges If neither hinges nor bonnet are damaged mechanically after the activation these elements need not to be replaced then. Hinges will be put to the original state by riveting, only actuators must be replaced.Beware! After the system has been activated for the third time it is always necessary to replace hinges and the airbag control unit. Re-riveting can be performed only with the specified rivet with plastic washer.32GB Figure SP96_12 shows the engine cover in the basic position, system was not activated. The first sensor of the active bonnet system is located at the centre under the radiator grill, the other two sensors on the sides under the bumper where headlamp extension washer is placed. All three sensors operate on the acceleration measuring principle. The arrows show the hinge locations and the direction the bonnet is lifted in.SP96_12active bonnet system acceleration sensorsFigure SP96_11 shows the engine cover after the system activation. The arrows show the hinge locations where Protected by copyright. for private or commercial purposes, in part or in whole, is not permitted actuators lifted theCopying bonnet. Beware! The sensor highlighted in yellow that is present on the car front end as well unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability doeswith not belong to the active engineincover system - it belongs to theA. airbag system, see Book SSP97. respect to the correctness of information this document. Copyright by ŠKODA AUTO S.�SP96_11airbag system acceleration sensorGB33 6. Chassis6.1 Chassis TypesFront axle McPherson axles are installed into all the variants of ŠKODA Octavia III model. Rear Axle Rear axle is installed into the Octavia III model in two versions: –m  ulti-element axle (see page 38) for the engines of power above 110 kW, for the models with  the rear axle drive connected by Haldex clutch, for the cars with CNG alternative drive – trailing axle (see page 37) for the engines of a power of up to 110 kWProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�front McPherson axle34GB the rear multi-element axle, (on Figure) or the trailing axle (see page 37)SP96_24Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB35 6.2 Front McPherson AxleUse was made of the kinematically independent type of MCPherson suspension for the front driven wheels. Each side of the axle is formed by a triangular arm and shock absorber unit. The telescopic absorber's axis is used as the top pivot of a wheel suspension – it has the kingpin's function. Front axle characteristic: – independent front wheel suspension with a good driving stability – double-row ball bearing with oblique contact screwed to the wheel boss – disc brakes with inner coolingshock absorber unit stabilizer draw barstabilizersteering gearboxProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted swinging strut unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�axle boxSP96_20axle arm36GB 6.3 Rear Trailing AxleIn the ŠKODA Octavia III car, the rear trailing axle is installed into the models with lower power engines (up to 110 kW inclusive). The axle is composed of two trailing arms that are connected with a transverse torsion element. The torsion element in the shape of U-profile in this axle has the stabilizer function as well. The axle body is connected at its front end to the body using a pair of rubber-metal beds. The axle springs are anchored in their bottom part into the steel beds that are fixed to the trailing arms. The upper part of springs leans against the body runner. Rear axle characteristic: – crank axle with two trailing arms interconnected with torsion element – the arms hold coiled springs and telescopic absorbers – disc brakes are used exclusively on the rear axleabsorber's anchorage into the bodytorsion element of reversed U-profiletelescopic damperProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�coiled spring rubber-metal bed holderSP96_18trailing armGB37 6.4 Multi-Element Rear Axle with Auxiliary FrameIn the ŠKODA Octavia III car, the rear multi-element axle is installed into the models with higher power engines (above 110 kW), this axle is then fitted to the Octavia III models with the connected (by Haldex clutch) rear axle drive and the cars with CNG alternative drive. The structure of multi-element rear axle with auxiliary frame for the new model of ŠKODA Octavia III is - as opposed to the previous variants of this axle - reworked. The main change is the new attachment of stabilizer that is not anchored to the longitudinal arms any longer as was the case, for example, in ŠKODA Octavia II 4x4 (see Fig. SP96_44). The stabilizer newly interconnects the lower cross – spring arms.stabilizer draw bar stabilizerSP96_44multi-element rear axle ofProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to theII correctness of information in this document. Copyright by KODA AUTO A. S.� ŠKODA Octavia 4x4 (location of stabilizer is indicated inŠ blue)Conception of auxiliary frame and mounting into the body All the multi-element axle's arms are fixed into an auxiliary frame through which the entire rear axle is mounted into the body. In the Octavia III models with the front drive, the auxiliary frame is mounted to the body fixedly with screws. The frame in 4x4 models is separated from the body by flexible beds.mounting the axle into the body by fastening the auxiliary frame through the flexible bedsSP96_4338GB Four arms on each side The axle is formed on each of its sides by three cross arms that assure the axle dynamics in transverse direction: –upper cross arm – lower cross arm – spring – connection cross arm Their exactly defined mounting allows for precision setting of the rear axle's kinematics and elastokinematics. Each side of the axle is completed with one longitudinal arm.upper cross armtelescopic damperrear axle's final drivecoiled cylindrical spring seated on the lower cross arm connection cross armHaldex clutchauxiliary frameSP96_19rubber-metal bed holderlongitudinal armThe multi-element structural design gives space for ideal reactions both to theinlongitudinal Protected by copyright. Copying for private or commercial purposes, part or in whole, and is not lateral permitted forces unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability induced in driving.with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB39 7.0 Brake SystemThe ŠKODA Octavia III car is equipped with double-circuit brake system with diagonal arrangement and the vacuum-operated brake booster. Division of the system into two separated brake circuits increases car safety under braking. With one circuit faulty, use is made of the other circuit that can be applied to stop the car. The brake and stabilization system's control unit is located on the right-hand side of the engine compartment to form a common assembly with the hydraulic unit. The car is equipped with a standard hand brake, the hand brake's control lever is connected with the rear brake mechanism by the Bowden cables. The front axle is fitted with disc brakes and single-piston floating caliper. The front brake discs are hollow with inner cooling. Their diameter differs depending on the applied motorization from 288 mm to 312 mm with a thickness of 25 mm. Full disc brakes of a diameter from 253 to 272 mm and a thickness of 10 mm are used on the rear axle (depending on individual motorizations). the brake and stabilization system control unit with the hydraulic unitactive brake booster with a main brake cylinderProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not on guarantee or accept any liability cooling the front with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�disc brakes with inner axle wheels40GB The brake system is further composed of the following sensors the signals of which form variables when the brake and stabilization function algorithms are calculated. –f  our speed sensors (on individual wheels) –s  teering wheel turning angle sensor (integrated in the steering gearbox) When the ESC Base or ESC High control units are used, it is also (see page 42 of this Book): –s  ide acceleration sensor (integrated in the ESC control unit) –l ongitudinal acceleration sensor (integrated in the ESC control unit) –r  otation speed sensor (integrated in the ESC control unit) –b  rake fluid pressure sensor (integrated in the ESC control unit)SP96_19Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�disc brakes on the rear axle wheelsBowden with brake cable assemblyGB41 7.1 Variants of Control Units for Brake and Stabilization SystemsThree variants of MK100 control units are introduced in ŠKODA Octavia III. The control units form one whole together with the hydraulic unit and hydraulic pump's electric motor. The M-ABS MK100 basic unit holds the function of ABS system. The advanced brake and stabilization functions are contained in the two higher variants of the ESC Base MK100 and EPB High MK100 control units. As compared with ESC Base unit, the ESC High unit can additionally operate the adaptive cruise control function in connection with the automatic gearbox. Detailed summary of functions is given in the table below. Control unit implements a function: ASR (driven wheel slippage control) MSR (Engine braking moment control) EDS (electronic differential lock) HBA (hydraulic brake assistant) RBS (brake disc drying) RKA (tyre pressure monitoring) HHC (Hill Hold Control) TSA (vehicle combination's stabilization) XDS (electronically controlled differential locking) EBP (Prefill function - preliminary pressurization of the brake system) MCB (multi-collision braking function) – – – – – – – – – M–ABS ESC Base ESC HighACC Base (adaptive cruise control for man. gearboxes) –or in whole, is not permitted Protected by copyright. Copying for private or commercial purposes, in partunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability ACC FTS (adaptive cruise control for automatic gearboxes) – by ŠKODA AUTO A. S.�– with respect to the correctness of information in this document. CopyrightSensors integrated in the MK100 control units The following sensors are integrated into the ESC Base and ESC High units: – side acceleration sensor – longitudinal acceleration sensor – rotation speed sensor – brake fluid pressure sensor Basic control unit M-ABS contains no integrated sensors. What is sufficient to implement the ASR and MSR functions are the signals from the group of external sensors (speed sensors, steering wheel turning angle sensor). Weight reduction, miniaturization, and placement As compared to the previous units, the MK100 units are lighter and they were cut in size as well. In ŠKODA Octavia III, the MK100 unit is placed in the right-hand part of the engine compartment.** T his applies for the left-hand steering. For the right-hand steering, the control unit is located on the left side of engine compartment.42GB M-ABS hydraulic unit with hydraulic pumpcontrol unithydraulic pump's electric motorSP96_46the M-ABS and ESC Base units have identical 38-pin connectorESC BaseProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� SP96_47ESC Highthe ESC Base and ESC High units have identical hydraulic unit and hydraulic pump's electric motorconnector 46 pinsSP96_48GB43 7.2 Multi-Collision Braking Function (MCB)The multi-collision braking function provides quick deceleration and car stabilization after an impact. By doing so it prevents further possible collisions when the car is not sufficiently braked or steered when after the crash, for example in the case when the car passenger is in a shock or injured. Function description In case a crash takes place when airbag is activated, the multi-collision braking function is turned on. The car starts to brake with a deceleration of 0.6 g, braking takes place until a speed of 10 km/hr is attained. At the same time with a significant automatic braking, the car braking distance trajectory is controlled by the unit of braking and stabilization systems so that the car is not oversteered. (For example, reduction of oversteering through the throttle pedal's automatic control.) Capitalisation The function is activated upon a signal from the airbag control unit. The condition for the multi-collision braking function to be activated is activation of at least one airbag in the car. Implementation The function is implemented by the brake and stabilization system control unit. Indication In case the multi-collision braking function is activated, brake lamps are also turned on automatically within this function to flash permanently. After the car's complete halt, the warning lights go automatically on. The car driver is informed of the MCB function activation on the composite instrument panel's display and by the illumination of ESC/ASR indicator lamp.Without the Multi-collision braking functionSP96_81Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�With the Multi-collision braking functionSP96_8244GB 7.3 Prefill Function (EBP)The Prefill function assures final pressurizing of the hydraulic brake system preparing by doing so the brake system for possible emergency situation. The function is activated by the throttle pedal quickly released by driver. This will reduce the brake action start time as well as the car's braking distance. M-ABS The M-ABS MK100 control unit does not contain the Prefill function and the Multi-collision braking function. These advanced functions are assured by the controlled units with ESC, see the function survey table on page 42 of this Book.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB45 8.0 Wheels and DiscsThe ŠKODA Octavia III car is equipped with the following series of steel and aluminium wheels. Steel wheels with all-area covers:SP96_49SP96_50cover SIDUS, 15" wheelscover TEKTON, 16" wheelsLight alloy wheels:Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP96_51 SP96_52 SP96_53VELORUM, 16" wheelsMINORIS, 16" wheelsILIAS, 16" wheelsSP96_54SP96_55DENOM, 17" wheelsTERON, 17" wheelsSP96_56SP96_57ALARIS, 18" wheelsGOLUS, 18" wheels46GB 9.0 Engines9.1 New MOB and MDB EnginesAs we already mentioned in Chapter 2.6 on page 8 of this Book, the MQB architecture conception also pertains to the engine units. The reworked engines of the new modular system are used exclusively in the ŠKODA Octavia III car now. Unified engines will thus interconnect the cars of the entire Group. The structures of the new MOB engines (gasoline type) and MDB engines (Diesel type) were reworked fully. For the modular structure to function properly, their modifications brought two basic characteristics: 1. P  ower units are designed in modular conception that provides for a wide variability of individual engine versions (with regard to the required power, valid emission regulations of individual regions, etc.). module elements of the new engines (EA211 series): –aluminium engine block – monolithic cylinder head lid with integrated camshafts – assembly module of turboblower and catalytic converter – timing gear drive and auxiliary power units drive – module of intake pipe with integrated coolant of compressed air – engine mounting brackets and timing gear drive covers –module of pump for coolant and thermostat compartment – air filter module – cylinder head with integrated exhaust manifold2. T  he engines acquired unified engine block orientation and the engine exhaust pipe was uniformly directed so that uniform connectivity of the further modular systems of the car is ensured (mounting of gearboxes, attachment of the exhaust system).SP96_58All the power units, both the Diesel and gasoline ones (of the new EA211, EA888 and EA288 series) are uniformly inclined by 12° backwards and the exhaust standpipes for all the power units are also led out in the back.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB47 The engine reconstruction was accompanied by their significant modernization.Development changes in the EA211 series engines (1.2 TSI / 63 kW and 77 kW, 1.4 TSI / 103 kW) – maintenance free cam belt – optimized combustion course – relieved crankshaft, con rod, and pistons – sixteen-valve technique newly in 1.2 TSI engines – turboblower and catalytic converter in one assembly module – variable valve timing – engine head with a cooled exhaust manifold – aluminium engine block newly for 1.4 TSI engineEngine cooling Dual-circuit system and two thermostats are used for engine cooling. The first thermostat is used for the engine block, the second thermostat for the cylinder head. The coolant volume was reduced simultaneously. This and individual temperature control of both cooling circuits lead to quicker warming of engine to the operating temperature. The engine oil cooler is also integrated into the engine block's cooling circuit. Engine head with an integrated exhaust pipe Exhaust manifold is integrated into the cylinder head. Exhaust gases are cooled by the cylinder head's water circuit. Lower temperature of exhaust gases then loads the catalytic converter a less. Integrated exhaust pipe accelerates the engine heating to the operating temperature.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP96_59The course of exhaust gas cooling in the exhaust pipe integrated into the cylinder headTurboblower Catalytic converter and turboblower together form one assembly module. The turboblower's by-pass valve is controlled by electric motor that allows precise and quick control. The engine reactions to the driver's commands are faster and shorter.48GB 9.2 Tabular Summary of MotorizationsModelŠKODA Generation 3 Octavia is equipped with six power units as of the sales initiation date. It is a quaternion of TSI supercharged spark-ignition four-cylinder engines and a pair of TSI spark-ignition four-cylinder engines which are therefore also equipped with turboblower.Gasoline power un