TECHNICAL DOCUMENTATION
SSP 100 1.6 l TDI and 2.0 l TDI Engines

This PDF is currently unavailable.
Read document text
1.6 l TDI and 2.0 l TDI Engineswith the Common Rail Injection System EA288 Design SeriesProCarManuals.comProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Self-Study ProgrammeŠKODA Service®100ProCarManuals.comProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Contents1. Introduction of EA288 Series MDB Engines � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1.1 1.6 l TDI and 2.0 l TDI Engines of the EA288 Series � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1.2 Modular Diesel Engines Design (MDB – Modularer Diesel-Baukasten) ���� ����� ���� ������ ����� ��� 2. Technical Data of the Engines � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2.1 1.6 l TDI CR Engine Parameters � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2.2 Power and Torque Characteristics of the 1.6 TDI CR 66 kW, 77 kW and 81 kW Engines � � � � � � � � � � � � � � � 2.3 2.0 l TDI CR 105 kW, 110kW Engine Parameters ��� ����� ����� ������ ���� ������ ���� ����� ����� 2.4 Power and Torque Characteristics of the 2.0 TDI CR 105 kW and 110 kW Engines � � � � � � � � � � � � � � � � � � 2.5 Power and Torque Characteristics of the 2.0 TDI CR 135 kW Engine � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3. Engine Mechanics � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3.1 Engine Blocks � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3.1.1 Structural Differences of the 1.6 l and 2.0 l Engine Blocks � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3.2 Balancing Shafts of the 2.0 l 135 kW � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3.3 Crank Mechanism � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3.4 Timing Mechanism and Auxiliaries Drive � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3.4.1 Timing Mechanism Drive by a Cogged Belt � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3.4.2 Auxiliaries Drive ������������������� ���� ������ ���� ����� ������ ���� ������ ���� ��� 3.5 Cylinder Head � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3.5.1 Camshaft Housing � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3.5.2 Cylinder Head Design - Overview (EU 6 compliant design) � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3.5.3 Intake and Exhaust Valves Layout ���� ����� ���� ������ ����� ����� ����� ���� ������ ���� 3.5.4 New Intake and Exhaust Ports Design ���� ����� ���� ������ ����� ����� ���� ������ ����� � 3.5.5 Cylinder Head Cooling � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4. Variable Valve Timing � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4.1 Hydraulic Camshaft Adjuster Module � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4.1.1 Hydraulic Camshaft Adjuster Functional Principle and Design � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4.1.2 Operating Ranges of the Hydraulic Camshaft Adjuster � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5. Crankcase ventilation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6. Engine Lubrication � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6.1 Oil Circuit ����������������������� ������ ���� ����� ������ ���� ������ ���� ����� ����� �� 6.2 Oil Filter Module � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6.3 Oil Pump � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6.3.1 Oil Pump Design � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6.3.3 Oil Pump Operating Ranges � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6.3.4 Oil Pressure Control Chart � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6.3.5 Oil Pressure Control Valve Position � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7. Turbocharger � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8. Cooling System � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.1 Cooling Liquid Overview � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.2 Small Cooling Circuit � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.3 Small Cooling Circuit at High Engine Loads � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.4 Big Cooling Circuit � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.5 Coolant Circuit for Boost Air Cooling � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.5.1 Boost Air Cooling � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.5.1.1 Boost Air Cooling Design � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.5.1.2 Boost Air Cooling System Sensors � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.6 Coolant Pump � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.7 Coolant Pump Operating Ranges � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8.8 Coolant Thermal Regulator � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9. Fuel System ������������������������ ����� ����� ���� ������ ���� ������ ���� ������ ����� �� 9.1 Common Rail Fuel Injection System � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9.2 Fuel System Diagram � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10. Exhaust Gas Recirculation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10.1 Emission Standards � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10.2 Low Pressure Exhaust Gas Recirculation - Engines Compliant with the EU 5 Emission Standard ���� ��� Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted 10.2.1 Recirculated Exhaust Gas Cooler with a Superposed Filter ��� ����� ����� ������ ���� ��� unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. AGR S. does not guarantee or accept any liability with respect to the correctness of information in this document.-Copyright by Compliant ŠKODA AUTO A. S.�the EU 4 Emission Standard � � � � � � 10.2 High Pressure Exhaust Gas Recirculation Engines with 10.4 Combined Low and High Pressure Exhaust Gas Recirculation System – Engines Compliant with the EU 6 Emission Standard � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11. Engine Control System Overview � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12. Special Workshop Tools and Equipment � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5 5 5 6 6 7 8 9 11 12 12 12 13 14 15 15 16 17 17 18 19 20 21 22 22 23 25 27 28 28 29 30 31 32 34 34 35 36 36 37 38 39 40 41 42 43 44 45 46 47 47 48 50 50 51 52 53ProCarManuals.com� 55 � 56 � 58GB3ProCarManuals.comProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�Instructions for assembly, disassembly, repairs, diagnosis and detailed user information can be found in VAS diagnostic testers and vehicle's onboard literature. Editorial date: 11/2013. This document is not subject to updating.SP95_004GB1. Introduction of the EA288 Series MDB Engines1.1 1.6 l TDI and 2.0 l TDI Engines of the EA288 SeriesIn Škoda Auto, the new MDB modular concept 1.6 and 2.0 liter engines are introduced for the first time in the Škoda Octavia III model. The 1.6 l drive unit is produced in three power versions - 66 kW, 77 kW and 81 kW. The higher displacement (2.0 l) engine also offers three power versions - 105 kW, 110 kW and the most powerful 135 kW version, which is reserved for the Škoda Octavia III RS model.1.2 Modular Diesel Engines Design (MDB – Modularer Diesel-Baukasten)The 1.6 l TDI and 2.0 l TDI engines have been designed in accordance with the new modular strategy of the VW Group. The dimensions, mounting and connecting points of these new engines are designed to enable their use as "global drive units". That way these engines are going to be used in vehicles of all the VW Group brands. The modular design is applied both to basic structural sub-assemblies (engine block, cylinder head, crank mechanism) and to additionally mounted engine parts (redesigned exhaust manifold closer to the engine, intake manifold with integrated intake air cooler).ProCarManuals.comProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB52 Technical Data of the Engines2.1 1.6 l TDI CR Engine ParametersPower versions of the 1.6 l TDI CR engine Engine Parameters Design 66 kW (engine code: CLHB) 77 kW (engine code: CLHA) 81 kW (engine code: CRKB)compression-ignition engine with direct high-pressure fuel injection, turbocharged by a turbocharger with variable blade geometry, liquid cooled, 2 x OHC, intended for front transverse mounting 4 1598 cm3 79.5 mm 80.5 mm 88 mm 4 66 kW at 2750–4800 min-1 230 Nm at 1400-2700 min-1 16.2 : 1 electronically controlled high-pressure common-rail injection system 1800 bar circulatory pressure oil lubrication with 100% oil filtering diesel EU 5, EU 6* 77 kW at 3000-4000 min-1 250 Nm at 1500-2750 min-1 81 kW at 3250-4000 min-1 250 Nm at 1500-3000 min-1Number of Cylinders Displacement Bore Stroke Cylinder Pitch Valves per Cylinder Max. PowerProCarManuals.comMax. Torque Compression Ratio Charging Max. Injection Pressure Lubrication FuelEmission EU 5 EU 5 Standard Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permittedunless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability Balancing Shafts NO with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The 66 kW and 77 kW power versions of the 1.6 TDI engine differ by engine control unit software, the structural design of both the versions is identical. The 81 kW version, compliant with the EU 6 standard, involves a different exhaust gas recirculation duct, see chapter 10 of this SSP. * T he engine hardware is prepared to comply with the EU 6 standard, as of the date of publishing this SSP (11/2013), the engine is offered as compliant with the EU 5 standard.6GB2.2 P ower and Torque Characteristics of the 1.6 TDI CR 66 kW, 77 kW and 81 kW Engines1.6 TDI CR 66 kW 1.6 TDI CR 77 kWT (Nm)P (kW)T (Nm)ProCarManuals.comn (min-1) 1.6 TDI CR 81 kWn (min-1)T (Nm)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�n (min-1) P – power, T – torque, n – engine revolutions engine torque curve engine power curveGBP (kW)7P (kW)2.3 2.0 l TDI CR 105 kW, 110kW Engine ParametersPower versions of the 2.0 l TDI CR engine Engine Parameters Design 105 kW (engine code: CRVC) 110 kW (engine code: CKFC) compression-ignition engine with direct high-pressure fuel injection, turbocharged by a turbocharger with variable blade geometry, liquid cooled, 2 x OHC, intended for front transverse mounting 4 1968 cm 81 mm 95.5 mm 88 mm 4 105 kW at 3500–4000 min 16.2 : 1 1800 bar diesel EU 4 NO EU 5 NO-1 3Number of Cylinders Displacement Bore Stroke Cylinder Pitch Valves per Cylinder Max. Power Max. Torque Compression Ratio Charging Max. Injection Pressure Lubrication Fuel Emission Standard Balancing Shafts4 1968 cm3 81 mm 95.5 mm 88 mm 4 110 kW at 3500–4000 min-1 320 Nm at 1750-3000 min-1 16.2 : 1 1800 bar320 Nm at 1750-3000 min-1electronically controlled high-pressure common-rail injection system circulatory pressure oil lubrication with 100% oil filteringProCarManuals.comProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�8GB2.4 Power and Torque Characteristics of the 2.0 TDI CR 105 kW and 110 kW Engines2.0 TDI CR 105 kWT (Nm)ProCarManuals.comn (min-1) 2,0 TDI CR 110 kWT (Nm)Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�n (min-1) P – power, T – torque, n – engine revolutions engine torque curve engine power curveGBP (kW)P (kW)9Power version of the 2.0 l TDI CR engine Engine Parameters Design 135 kW (engine code: CUPA) compression-ignition engine with direct high-pressure fuel injection, turbocharge by a turbocharger with variable blade geometry, liquid cooled, 2 x OHC, intended for front transverse mounting 4 1968 cm3 81 mm 95.5 mm 88 mm 4 135 kW at 3500–4000 min-1 380 Nm at 1750-3000 min-1 15.8 : 1 electronically controlled high-pressure common-rail injection system 2000 bar circulatory pressure oil lubrication with 100% oil filtering diesel EU 5 YESNumber of Cylinders Displacement Bore Stroke Cylinder Pitch Valves per Cylinder Max. Power Max. Torque Compression Ratio Charging Max. Injection Pressure Lubrication Fuel Emission StandardProCarManuals.comBalancing ShaftsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�10GB2.4 Power and Torque Characteristics of the 2.0 TDI CR 135 kW Engine2.0 TDI CR 135 kWT (Nm)ProCarManuals.comProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�n (min-1)P – power, T – torque, n – engine revolutions engine torque curve engine power curveGBP (kW)113. Engine Mechanics3.1 Engine BlocksThe blocks of the 1,6/2,0 l TDI engines are made of GG-GJL-250 grey cast iron, which displays good combination of strength and hardness. The used material has good vibration damping properties.3.1.1 Structural Differences of the 1.6 l and 2.0 l Engine BlocksThe concept of 1,6 l and 2,0 l engine blocks is uniform, having cylinder pitch of 88 mm. The diameter of cylinders on the 1,6 l and 2,0 l block differs. The 2,0 l 135 kW engine is additionally equipped with balancing shafts and the engine block is modified to enable their embedding. See page. 13 of this SSP.ProCarManuals.comSP100_2the 1.6 l engine block does not include the balancing shafts moduleEngine 1,6 l 66 kW 1,6 l 77 kW 1,6 l 81 kW 2,0 l 105 kW 2,0 l 110 kW 2,0 l 135 kWCode Engine CLHB CLHA CRKB CRVC CKFC CUPAEmission standard. EU 5 EU 5 EU 5, EU 6* EU 4 EU 5 EU 5Bore 79.5 mm 79.5 mm 79.5 mm 81 mm 81 mm 81 mmStroke 80.5 mm 80.5 mm 80.5 mm 95.5 mm 95.5 mm 95.5 mmPitch of cylinders 88 mm 88 mm 88 mm 88 mm 88 mm 88 mmBalancing shafts NO NO NO NO NO YES* T he engine hardware is prepared to comply with the EU 6 standard, as of the date of publishing this Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted SSP (11/2013), the engine offered compliant with the EU 5 unless is authorised by as ŠKODA AUTO A. S. ŠKODA AUTO A. standard. S. does not guarantee or accept any liabilitywith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�12GB3.2 Balancing Shafts of the 2.0 l 135 kWTwo counter-rotating balancing shafts with counterweights are used to suppress 2nd order inertial forces generated by pistons moving in the cylinders.. The balancing shafts are rotating at double angular velocity of the crankshaft. The change in the direction of rotation of the second balancing shaft is executed by means of an intermediate gear. Their drive is derived from the crank shaft via helical gears. Shafts are supported in roller bearings. Bearings are lubricated by oil mist from the engine block.ProCarManuals.comSP100_1supporting of the balancing shafts of the 2,0 l 135 kW enginecylindrical bearings supporting the shaft in the block Protected by copyright. Copying for private or commercial purposes, in engine part or in whole, is not permitted balancing shaft with 1 respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liabilitybalancing shaft 2crankshaftSP100_3intermediate gearGB133.3 Crank MechanismThe crankshaft, supported by five bearings, is balanced by four counterweights. Cracking has been used to achieve good connection of the head of the forged connecting rod bearing cap. Piston tops feature depressions, without recesses for pistons. These depressions are positioned off-center in order to correspond to the structural position of the valves in the cylinder head. The depression in the piston crown forms part of the combustion space, and therefore is significantly thermally loaded. The pistons are hollow and cooled by oil channels. Oil is sprayed to the piston hollows by nozzles at the bottom dead center. The crankshaft is fitted with three gears: – spur gear for timing mechanism drive – spur gear for oil pump drive – helical gear for driving balancing shafts (of the 2,0 TDI 135 kW)ProCarManuals.comoil cooled depression in the piston crownbalancing shafts drive geartiming mechanism drive gearSP100_4piston rodbearing oil pump Protected by copyright. Copying for counterweight private or commercial purposes, in part or in whole, is not permitted unlessgear authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability drivewith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�14GB3.4 Timing Mechanism and Auxiliaries DriveDrive of the timing mechanism and auxiliaries is executed by means of two belts. One cogged and one ribbed belt.3.4.1 Timing Mechanism Drive by a Cogged BeltThe cogged belt transfers rotary motion of the crankshaft to: – camshafts – high pressure fuel pump – switchable coolant pump Proper tensioning and routing of the cogged belt is assured by means of an automating tensioner assembly with a pair of guide pulleys.ProCarManuals.combelt pulley camshafts guide pulleyhigh pressure fuel pump pulleyProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�belt tensionercoolant pump pulleyguide pulleycrankshaftSP100_5GB153.4.2 Auxiliaries DriveThe auxiliaries are driven by a ribbed belt, which is driven by the crankshaft via an oscillation damper. Proper tensioning of the ribbed belt is assured by means of a tensioner pulley. The following auxiliaries are driven by the ribbed belt: – alternator – A/C compressortensioner pulleyalternatorProCarManuals.comcrankshaft oscillations damperSP100_6A/C compressorThe used ribbed belt shall always be mounted in the same direction of rotation, otherwise it may get damaged.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�16GB3.5 Cylinder HeadThe cylinder head module is composed of the following structural parts: – camshaft housing (bearing frame with permanently integrated camshafts) – cylinder head with valves and other fittings – variable valve timing modules (on EU 6 compliant engines)camshaft housingProCarManuals.comvariable valve timing module (only on engines compliant with the EU 6 standard)SP100_7structural part of the cylinder head with valves and other fittingsProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�3.5.1 Camshaft HousingThe camshafts are supported in the camshaft frame using the method of thermal joining. The same method is used to mount the individual cams to the shafts. In the process of thermal joining, cams and the frame are placed in exact positions using a special auxiliary jig, and subsequently the cams are heated. Then cooled down shafts are inserted into the jig. Once temperatures of the individual components equalize, a very strong connection of the whole module is achieved. The MDB 1.6 l TDI and 2.0 l TDI engines are the first compression-ignition engines within the VW Group, where thermal joining replaced the previously used hydraulic pressing-on of shaft components.GB173.5.2 Cylinder Head Design - Overview (EU 6 compliant design)injector holder high pressure rail fuelinjector unitcrankcase venting and vacuum reservoirProCarManuals.comProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�cylinder head covercamshaft housingpressure reservoir of the camshaft adjustercamshaft adjuster valve N205rocker arms with rollersvalvesintake manifold module with integrated cooler of intake airSP100_8cylinder head18GB3.5.3 Intake and Exhaust Valves LayoutThe previous generation of diesel engines had one camshaft dedicated for intake valves and the other for exhaust valves. The layout of valves on the new generation of MDB engines is modified, so now each of the camshafts actuates four intake and four exhaust valves.EA189 engines layout of valvesEA288 engines layout of valvescamshaft axis crankshaft axis camshaft axisexhaust valvesintake valvesProCarManuals.comThe valves are now rotated by 90° in relation to the crankshaft axis. When viewed from the intake flange side, a pair of intake valves of the new EA288 engines is located behind each other. The same applies to the pairs of exhaust valves.exhaust cams intake camsSP100_9Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�The reason to modify the layout of valves was the new system of their variable timing. This system will be introduced in the EA288 engines compliant with the EU 6 emission standard. The newly oriented intake and exhaust valves enable modifications of intake port shape and using intake manifold without swirl flaps.GB193.5.4 New Intake and Exhaust Ports DesignThe shape of ports is also adapted to the new layout of valves. The intake ports feature tapered seats that deliver good swirl characteristics in the full range of valve lift. This design of intake ports enabled elimination of the swirl flaps. The newly designed intake ports project from the cylinder head in vertical direction. The exhaust ports are routed on the opposite side of the cylinder head. This vertical arrangement of the intake flange enables ergonomic connection of quite a big intake manifold module with integrated boost air cooler. Thanks to this design, the engine structure remained compact, without unnecessary increase in height.first exhaust valve of the second cylinderfirst intake valve of the second cylinder intake air second intake valve of the second cylinderProCarManuals.comsecond exhaust valve of the second cylinderfirst cylinderintake side exhaust gasesexhaust sideSP100_10Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�20GB3.5.5 Cylinder Head CoolingIn order to achieve efficient cooling of the areas adjacent to the combustion space, two separate water channels have been integrated into the cylinder head, which are located on top of each other - the upper and lower cylinder head cooling channel. The upper and lower coolant channel merge into a common outlet to the heat exchanger for interior heating in a heating flange, which is provided with an air bleeding collar. When the engine is cold, the coolant in the upper and lower cooling channel is flowing throughs recirculated exhaust gas cooler and further to the heat exchanger. upper cooling channel of the cylinder head outlet of the upper cooling channelProCarManuals.comoutlet of the lower cooling channelSP100_11lower cooling channel of the cylinder headSP100_12the coolant flows to the lower cylinder head channel from the engine block cooling channelsThe cooling channels are not connected on an unmachined cylinder head casting. The connection of the lower and upper cooling channel is created by milling a technological opening from the side of the cylinder head, the opening is then sealed by a plug. The connection created in this way then enables passage of the coolant from the lower to the upper cooling channel, see the yellow arrow on the picture.SP100_13GBProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�214. Variable Valve TimingVariable valve timing will be used on MDB engines compliant with the new EU 6* emission standard.The main reason to introduce variable valve timing on diesel engines is the need to comply with the new emission standards. Another justification is the trend of fuel consumption reduction. Variable valve timing with earlier or later closing of intake valves enables decreasing the NO x or CO2 emissions. By variable timing of the intake valves, it is even possible to decrease the efficient compression ratio. This results in lower compression temperatures and consequently lower NO x emissions.4.1 Hydraulic Camshaft Adjuster ModuleProCarManuals.comVariable valve timing is executed by means of a hydraulic camshaft adjuster. The new layout of valves, which combines intake and exhaust cams on each of the camshafts, also enables to vary timing of the exhaust valves.hydraulic adjuster moduleProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP100_14 SP100_15EU 6 – camshaft module with the adjusterEU 4, EU 5 - camshaft module without the adjusterThe variable valve timing enables: – optimized charging at full load – operation at lower emission levels and reduced fuel consumption due to variable, which also means more efficient, compression ratio – maximum utilization of the expansion stroke – high compression ratio at cold starts* On the closing date (11/2013) of this SSP, the 1.6 l TDI 81 kW engine was offered in the EU 5 version with variable valve timing, therefore its hardware is ready to comply with the EU 6 standard.22GB4.1.1 Hydraulic Camshaft Adjuster Functional Principle and DesignTorque transfer from the crankshaft to the driven camshaft Crankshaft motion is transferred via the driving camshaft to the stator of the hydraulic camshaft adjuster motor by means of a pair of gears. The hydraulic camshaft adjuster is located in the axis of the driven camshaft. The stator of the hydraulic camshaft adjuster motor is permanently connected to the gear of the second camshaft. However, this gear is separated from the driven camshaft by a bearing. That way torque is only transferred from the stator to the rotor of the hydraulic motor. The rotor is permanently connected to the driven camshaft.piston-type pressure oil reservoirProCarManuals.comthe swiveling hydraulic motor of the adjusterdriven camshaft driven by driving camshaft via the hydraulic motor of the camshaft adjusterdriving camshaftSP100_16stator cover with the gearProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability rotor Copyright by ŠKODA AUTO A. S.� with respect to the correctness of information in this document.statorstator coverSP100_18electromagnetic valve coil mechanical blocking pincontrol valveGB23Operating Principle of the Camshaft Adjuster The hydraulic adjuster is supplied by pressure oil from the oil pump. The angle of camshaft adjustment is controlled by the engine control unit by means of a 4/2 way proportional control valve. The control valve is controlled by an electronic valve by means of pulse width modulation (PWM). The adjustment of the camshaft is achieved by the force of pressure oil acting in the chambers in between the rotor and the stator. During engine starting, the adjuster motor is mechanically locked. Locking the motor is performed by means of a blocking pin, until the necessary oil pressure is built. In order to pressurize the hydraulic adjuster as quickly as possible, an auxiliary pressure reservoir with a one way valve is used.sectional view of the camshaft adjusterreturn spring rotorcontrol valve electronic valve for position adjustment of the camshaftProCarManuals.comcamshaftSP100_16statorcover including gear fitted to the statorProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�pressure oil reservoirsectional view of the pressure oil reservoirpiston-type pressure reservoir with a springSP100_16SP100_16Hall sensor of camshaft adjustment angleone way valve oil strainer24GB4.1.2 Operating Ranges of the Hydraulic Camshaft AdjusterVariable valve opening/closing chart exhaust intake Key: valve travel 1 – exhaust: variable opening 2 – intake: variable opening 3 – intake: variable closing 1 2 3TDC BDC piston stroke (BDC - bottom dead center, TDC - top dead center)BDCSP100_21ProCarManuals.comThe camshaft adjuster valve is controlled in a way that oil pressure acts in both the chambers of the hydraulic motor. The rotor, permanently connected to the camshaft, moves to the "advance" or "retard" direction based on the ratio of pressures in the pressure chambers between the rotor and the stator. Once the engine is shut down, the hydraulic adjuster is set into the "advance" opening position by the spring and gets locked in this position by the locking pin.Camshaft position adjustment to the "ADVANCE" position In case zero PWM signal is applied to the electronic valve, the oil pressure gets through the camshaft adjuster valve to the operating chamber "A" of the hydraulic motor. The rotor starts moving in the direction of the operating chamber "B" (towards the "advance" position). Finally the locking pin engages, which locks the camshaft in the "earlier" position. In case, the camshaft is set to the "advance" position, both the intake valves are opened simultaneously.pressure oil reservoir to the motor system one way valve oil strainer A B valveProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP100_19oil pumpcamshaft adjusterGB25Camshaft position adjustment to the "RETARD" position In case active PWM signal is applied to the electronic valve, the oil pressure gets through the camshaft adjuster valve to the operating chamber "B" of the hydraulic motor. The pressure reservoir actively supports maintenance of pressure in the chamber "B". The hydraulic motor is thus turning the shaft to the "retard" position. In case, the camshaft is set to the "retard" position, the rear intake valve is opened. (The valve on the driving camshaft.) The front valve on the camshaft with variable timing opens with offset. Control by means of pulse width modulation - PWM - enables continuous variation of the camshaft position.ABProCarManuals.comSP100_20Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�26GB5. Crankcase VentilationCylinder Head Cover The cylinder head cover is made of plastic, its primary function is to seal the cylinder head. The cover integrates the following components: oil filler, vacuum system pressure reservoir and crankcase ventilation system. Oil Separation Due to the pressure difference in between the combustion chambers of the engine and the crankcase, gas leakage takes place between the piston rings and cylinder slide surface into the crankcase. These gasses are referred to as "blow-by" gasses. Gases in the crankcase contain oil in the form of aerosol. Oil gets separated in the crankcase ventilation system. The gas first passes through a coarse oil separator and then a fine cyclone separator. The purified gas is routed via a pressure control valve into engine intake and combusted. Separated oil returns back to the oil sump.oil fillerheating element of the crankcase venting system N79 (only for cold climate countries)ProCarManuals.compurified gas (oil free) is fed to the engine intakegasses partially purified in the coarse separator continue into the cyclone Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted separator unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability pressure control valvewith respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�fine, cyclone separator of oilvacuum reservoirseparated oil returns back to the oil sumpSP100_23oil return line from the fine separatorgravity valve of the oil return lineGB276. Engine Lubrication6.1 Oil Circuitcamshafthydraulic lifters of valvesturbochargerProCarManuals.compressure oil reservoir for the camshaft adjusterProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�pistons oil nozzles for piston cooling crankshaftSP100_34oil sumpoil pump oil filter module with oil cooler28GB6.2 Oil Filter ModuleNext to the oil filter, the oil filter module also contains engine oil cooler. The replaceable oil filter insert is placed in a casing with a by-pass valve. The by-pass valve opens in case the oil filter gets clogged, in order to provide for continued engine lubrication is such a case. The oil filter module contains two pressure switches: – F378 pressure switch for low, reduced oil pressure (0.3–0.6 bar – switching pressure) – F378 pressure switch for high oil pressure(2.5-3.2 bar – switching pressure)by-pass valve of the oil filter coolant outlet from the oil cooler oil coolerProCarManuals.comoil pressure switch F1 for the high oil pressure coolant inlet to the oil cooler oil pressure switch F378 for the reduced oil pressureoil inlet for lubricating points of the engineSP100_25replaceable oil inlet insert Protected by copyright. Copying for private or commercial purposes, in part or oil in whole, is not permitted from the of the unless authorised by oil ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability pump with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� filterGB296.3 Oil PumpThe pump is doubled, next to oil pressure delivery, it also functions as a vacuum pump. The oil pump is located right in the oil sump and is bolted to the lower part of the engine block. The drive from the crankshaft is transferred to the pump by a cogged belt, which operates in the oil bath. The cogged belt has no tensioner pulley. The oil pressure control valve is not directly integrated in the oil pump, but it is located in the lower part of the engine block, right above the oil pump.ProCarManuals.comoil/vacuum pump in the oil sumpoil pump cogged belt cover with integrated crankshaft sealing ringSP100_31driven by cogged beltProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�30GB6.3.1 Oil Pump DesignOil Pump The oil pump varies the pressure in the lubricating system by varying the oil flow rate. From the design point of view, it is a blade-type chamber pump with eccentrically positioned control ring. The ring is used to vary the oil flow rate. The suction pipe is specially shaped in order to provide for reliable oil suction from the oil sump even at high transversal accelerations of the vehicle. Vacuum Pump The vacuum pump draws air from the brake booster. From there, air passes through membrane valves into the engine block, where it is used to equalize pressure in the crankcase. The double membrane valve has sufficient cross-section to drain oil from the vacuum pump.membrane valve double membrane valvecontrol ring control pistondriving cogged belt pulleyProCarManuals.comrotor with a blade of the vacuum pumpoil pump coverSP100_26vacuum pump coversafety relief valve suction piperotor with blades forming chambers control springProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB316.3.3 Oil Pump Operating RangesLow Flow Rate for engine lubricationlower pumping spacecontrol ringSP100_29control pistonProCarManuals.comrotor with blades forming chambers suction pipe control springIn the low flow rate mode (lower engine rpm range) the N428 valve is grounded (voltage free). That way the connecting oil channel, leading to the control piston, is open. Oil pressure starts acting on the surface of the control piston, shifts it again the force of the piston spring and opens the oil channel to the surface, which actuates the control ring. Oil pressure acts on the pump control spring and turns the control ring counter-clockwise, i.e. towards Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted authorised by ŠKODA AUTO A. pumping S. ŠKODA AUTO A. S. doesThe not guarantee accept any chambers liability the center of theunless pump with blades forming chambers. size ofor pumping in between the with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.� blades is decreased, which decreases the flow rate through the engine lubrication system.connecting oil channel (connected - open) control piston spring (being compressed) oil pressure control valve N428pump control spring (being compressed) oil pressure from the oil circuitoil sumpcontrol pistonone-way valveSP100_2832GBHigh Flow Rate bigger pumping spaceSP100_29ProCarManuals.comIn the high flow rate mode (lower engine rpm range) the N428 valve is under voltage. The connecting oil channel is being emptied. The control piston spring closes the channel to the actuating surface of the control ring. The control ring is thus relieved of oil pressure and the oil pump control spring sets it to the upper position of the supporting bed by clockwise motion. The control ring can move out the center position and increase the pumping space in between blades. This increases the oil flow rate through the lubricating circuit.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�control piston spring (being released) pump control spring (being released)connecting oil channel (disconnected closed)SP100_27GB336.3.4 Oil Pressure Control ChartThe oil pump operates in two oil pressure modes depending on engine rpm. The mechanism of the oil pump maintains reduced oil pressure in the range of 1.8 to 2 bar when the engine operates at up to 3000 rpm. This pressure is maintained by varying the oil flow rate. For high engine rpm values - above 3000 rpm the oil pressure is increased to 3.8 to 4.2 bar.5oil pressure (bar)4high pressure level: oil pressure 3.8 – 4.2 bar32low pressure level: oil pressure 1.8 – 2.0 bar1010002000300040005000SP100_32engine rpmProCarManuals.com6.3.5 Oil Pressure Control Valve PositionThe oil pressure control valve N428 is not directly integrated in the oil pump, but it is located in the lower part of the engine block, right above the oil sump.to engine oil circuitvacuum lineProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�combine oil/vacuum pump in the oil sumpSP100_33oil pressure control valve N42834GB7. TurbochargerThe turbocharger module is composed of an exhaust gas collector, in which a turbine wheel with variable blade geometry (VGT) is integrated. The VGT technology enables to change the pitch of turbocharger blades based on current engine load in order to optimize charging of cylinders. The turbocharger is controlled by a vacuum boost pressure controller with a position sensor - G581. The turbochargers for MDB engines are delivered by several suppliers.vacuum boost pressure controller with boost pressure controller position sensor G581ProCarManuals.comintake air inlet exhaust collector manifold with integrated turbine wheelProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP100_40compressed air outlet to the boost air coolerpulsation dampersupply of exhaust gas for recirculationThe picture of the turbocharger corresponds to the EU 6 compliant version.GB358. Cooling SystemThe EA288 series MDB engines are equipped with an intelligent multi-circuit system for engine temperature control. The core of the cooling system is formed by a switchable pump and a coolant temperature regulator. Based on the current engine temperature, its big cooling circuit is being blocked or opened. The whole system is designed to maximally shorten the heat up phase after cold engine starts. Further tasks of the system are to quickly heat up the vehicle interior and to operate the engine in ideal operating temperature range in order to achieve minimum internal friction. The cooling system is composed of three circuits: – small cooling circuit (micro-circuit) – big cooling circuit (high-temperature cooling circuit) – boost air cooling circuit (low temperature circuit)8.1 Cooling Liquid Overviewauxiliary pump for interior heating V488 recirculated exhaust gas (AGR) coolerheating heat exchangerProCarManuals.comgear oil cooler coolant equalizing vesselcoolant temperature sensor G62cooing liquid pump kapaliny coolant thermal regulatorcylinder head coolant valve N489boost air cooler vzduchuSP100_35 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�engine oil coolerboost air cooling circuit pump V188cooler of the boost air cooling circuitmain radiatorthrottle flap control unit J338Note: The cooling system diagrams in Chapter 8 apply to the EU 5 compliant version of the engine.36GB8.2 Small Cooling CircuitThe small cooling circuit passes through: Cylinder head - recirculated exhaust gas cooler (AGR) - heating heat exchanger - auxiliary electrical coolant pump. At cold engine starts, only the small cooling circuit is active in order to enable quick engine heat up and interior heating in case of such requirement. The switchable coolant pump is powered, which means it is closed. The coolant circuit in the engine is thus disconnected and the coolant in it is not moving - this enables the cold engine to get very quickly heated up. When it is required to quickly heat the interior (driver's requirement received by the air-condition control unit) the heating circuit pump V488 is activated. That way the coolant only circulateds in the small cooling circuit and heats the heat exchanger for interior heating.auxiliary pump for interior heating V488heating heat exchangerrecirculated exhaust gas (AGR) coolerProCarManuals.comProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�coolant temperature sensor G62 the coolant pump kapaliny is closed cylinder head coolant valve N489 activeSP100_41The switchable coolant pump is controlled by the cylinder head coolant valve N489.GB378.3 Small Cooling Circuit at High Engine LoadsAs the engine load is increasing and speed rises over 3000 rom, the switchable coolant pump is activated and the coolant start flowing through the engine. Once engine speed drops below 2000 rpm, the switchable coolant pump stops. The engine is then again operated without coolant circulation. The coolant pump is permanently active once coolant temperature in the cylinder head exceeds 60°C. This temperature correspond to a heated-up engine. As the coolant did not yet reach operating temperature, the thermal regulator is still in the by-pass mode and does not open the passage to the big cooling circuit.auxiliary pump for interior heating V488heating heat exchangerrecirculated exhaust gas (AGR) coolerProCarManuals.comcoolant temperature sensor G62Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�coolant pump inlet open coolant thermal regulator in the by-pass modedeactivated cylinder head coolant valve N489SP100_4538GB8.4 Big Cooling CircuitOnce the coolant is heated to the operating temperature, the thermal regulator opens and the coolant start flowing through the big cooling circuit. The thermal regulator further controls the coolant temperature.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�ProCarManuals.comcoolant pump opencylinder head coolant valve N489 deactivatedSP100_44radiatorcoolant thermal regulator open and controlling coolant temperature; the thermal controller is located at the coolant inlet to the radiatorGB398.5 Coolant Circuit for Boost Air CoolingThe coolant circuit for boost air cooling is fully independent. The V188 pump speed is controlled based on temperature in the intake manifold. The value is sensed by the boost air temperature sensor - G811.ProCarManuals.comProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�boost air coolerSP100_43boost air cooling circuit pump V188heat exchanger of the boost air cooling circuit40GB8.5.1 Boost Air CoolingAir compression in the turbocharger results in undesirable temperature increase. The intake gas temperature is further increased by exhaust gas recirculation upstream the turbocharger. In diesel engines, in order to avoid the need to combust too rich mixture, it is necessary to combust the intake air. Boost air cooling on the EA288 series MDB engines is similar to the EA211 series petrol engines. A boost air cooler (air-to-coolant) is integrated in between the turbocharger and cylinder head.boost air cooler turbochargerProCarManuals.comSP100_39compressed air line from the turbochargerProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�heat exchanger of the boost air cooling circuitboost air cooling circuit pump V188Boost air cooling is executed by means of a separate low-temperature coolant circuit with coolant-to-air heat exchanger. An electrical coolant pump V188 with variable speed is used to circulate coolant in this circuit.* The design of the heat exchanger of the boost air cooling circuit may differ based on the version used.GB418.5.1.1 Boost Air Cooling Designturbocharger boost air coolerair filterSP100_38ProCarManuals.comintake air inletThe compressed air cooler integrated in the intake manifold is completely made of aluminum. It is composed of cooling plates, lamellas, cover plates and coolant ports. The coolant flows through the W -shaped cooling plates in counter-flow mode. The special shape of the cooling plates divides the flow along all the length of the flat tube and also inverts the flow. This enables good heat transfer from the aluminum sheet metal to the coolant.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability coolant circuit with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�connectionsSP100_37throttle flap42GB8.5.1.2 Boost Air Cooling System SensorsSensor of the boost air cooler include input boost air temperature sensor G42 and boost air pressure sensor G31. Boost air temperature G811 is fitted on the cooler outlet.aluminum boost air coolerboost air temperature sensor G811 downstream the boost air coolerboost air temperature sensor G42ProCarManuals.comProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�SP100_36inlet channel to the cooler of boost airboost pressure sensor port G31connection to the throttle flapGB438.6 Coolant PumpThe cooling system of the EA288 series MDB engines features a switchable pump. When switched off, the rotor is covered by a control slide valve and thus the coolant is not pumped and circulating through the cooling circuit. Switching of the pump is controlled by means of a solenoid valve - N489. The coolant pump is driven by the flat side of the clogged belt.axial piston pumpcylinder head coolant valve N489return springdrive pulley permanently connected to the shaftProCarManuals.comrotor with bladesSP100_50control slide valveN489 pump with axial piston ring piston control slide valvedrive pulley with shaft bearingrotor with blades with integrated swing discSP100_47pump housingProtected by copyright. Copying for private or commercial sealing rings purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability of the ring piston with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�guide bush with coolant channelscontrol slide valve sealingreturn spring44GB8.7 Coolant Pump Operating RangesPump with Axial Piston The housing of the coolant pump contains a miniature pump with an axial piston. This pump drives the swing disk located on the rear side of the rotor with blades. The miniature pump is not switchable and is permanently running once the engine is operating. Standstill Coolant Mode In this mode, the N489 valve is powered. Thus the outflow channel to the coolant circuit is closed. The miniature valve with the axial piston remains permanently operational and builds pressure in the enclosed system, which shifts the ring piston. The shifted piston moves the control slide valve against a spring, the slide valve thus overlaps the rotor with blades and interrupts coolant flow. control slide valve overlapping the rotor with bladesclosed outflow channel pump with axial pistonSP100_48ProCarManuals.comshifted ring pistonCirculating Coolant Mode In this mode, the solenoid valve N489 is not powered. Thus the outflow channel to the coolant circuit is open. Hydraulic pressure drops in the pump control channel and the spring moves the ring piston and control slide valve back to the initial position. The rotor with blades is thus revealed again and pumps the coolant.open outflow channel control slide valve retracted back behind the rotorSP100_46Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�GB458.8 Coolant Thermal RegulatorChanges in coolant flow in the thermal regulator - a 3/2-way valve, are performed by a thermostat - an expansive sensor filled with wax. Once the coolant temperature reaches the standard operating level, the thermostat starts closing the small cooling circuit and simultaneously opens the big cooling circuit.Small Cooling Circuit Modecoolant inlet from the engine block.SP100_51connec