TECHNICAL DOCUMENTATION
SSP 191 Passat B5

This PDF is currently unavailable.
Read document text
Service.191The Passat ‘97The PresentationConstruction and operationSelf Study ProgrammeOnly for internal use. © VOLKSWAGEN AG, Wolfsburg All rights reserved. Subject to modification. 640.2810.10.00 Technical Status: 09/96 ` Printed on chlorine-free bleached paper.Service Department191/01The most remarkable features of the new Passat are its: l High economy l Dynamic body styling l High-quality interior equipment designed with great attention to detail l Pioneering safety engineeringIn this booklet, we would like to provide you with an initial overview showing how we justify making these claims.2PageThe Passat ‘97 Environmental Protection and Recycling Body Vehicle Safety Engines and Gearboxes Running Gear Brakes Steering Electrics Extended Systems04 08 10 15 19 26 29 30 31 36Important ! / NoteNewThe Self Study Programme is not a Workshop Manual. Please refer to the relevant Service Literature for all inspection, adjustment and repair instructions.3The Passat ‘97To avoid confusion, concise examples are used to illustrate the various aspects of this all-embracing vehicle concept.You can find detailed information in Self Study Programme No. 192 Passat ‘97 – The Engineering.192Service.P DerDiea assnikt '97h Tecst KonruktionundFunktionst Selbstudienprogramm191/86Kundendienst191/734Dimensions and Weights2707 mm 4675 mm191/711740 mmTrack widths front rear 1498 1500 mm mmWeights Unladen weight Max. permissible weight appr. 1200 kg appr. 1805 kg5The Passat ‘97The Platform - an Advantage for WorkshopsThe term “platform” is frequently used in publications although its fundamental meaning is not explained. The result of this is that people are often unsure of what the term “platform” implies. The vehicle consists of a) the platform and b) the body. Design and vehicle characteristics dictate what form the body takes. In the eyes of the customer, the body characterises the styling of the vehicle as a whole.The bodyThe platform191/76The Passat ‘97191/446PlatformThe platform comprises both common parts and system parts.Common parts e.g. sliding sunroof, steel rim Common parts may only be used in platform vehicles without change. They do not influence the design of the vehicle.System parts e.g. seat Some system parts are identical. They have to be adapted since they are the interface between the platform and body.System partCommon part FrameAdapted part Vehicle-specific seat upholstery, seat cover, etc.191/90The advantages for workshops like yourself are: More clarity as regards the spare parts situation Simplified inventory management Fewer different special tools and fixtures Easier assembly and repair7Environmental Protection and RecyclingThe concept of eco-friendliness was pursued consistently throughout development of the new Passat. We would now like to show you some aspects of this topic which are also of interest to workshops.RecyclingNot least the recycling requirements present workshops with problems such as identifying, presorting and storing materials and waste operating media. To achieve this, the following measures were taken: l Identification of plastic part materials l Fewer composite materials l Reduction in fine sealing through the use of laser welding l No parts containing CFCs are used.Take bumpers for example: Bumpers were previously manufactured from composites. What the term “composite” means is that different materials are combined with one another in such a way that subsequent separation into clean material streams is no longer possible. If a plastic is to be recovered for recycling, it should, if possible, be sorted according to type for recycling purposes. This means that different types of plastic, for example, must not be mixed with one another. The bumpers on the Passat are recyclable because they do not contain composites. . Collection + sorting Cleaning + recycling191/67Recycled plastic8SolventsEven during production, every effort is made to keep environmental pollution to a minimum. To achieve this, the following measures were taken: l Full galvanisation means much less wax and PVC underseal l Water-dilutable paints including water-based clear coat l Stringent requirements for materials ensure lower emissions in the vehicle interiorEnergy + ResourcesRaw materials and energy are in limited supply on the planet Earth. We must use them sparingly. To achieve this, the following measures were taken: l Less energy consumption during production through the use of new joining techniques (e.g. laser welding) and complete assemblies (e.g. side section of body), l Full galvanisation and an 11-year warranty against corrosion perforation ensure high value retention and conservation of resources. Take laser welding for example: During laser welding, a highly concentrated light beam with a high energy content is used instead of a gas flame to join the components. No additional welding material is required, as is the case during MIG welding for example. Laser welded seams are extremely clean and do not need to be reworked. Laser welding offers a more favourable energy balance than conventional welding techniques.191/039BodyThe following will be of interest to you:l l l lThe Passat in the wind tunnel Fully galvanised body Greater body rigidity Use of high-strength steel partsl Strategy of using common platform for body parts l Ease of repair demonstrated using door module as example l Rear collision demonstrated using bumper as exampleThe Passat in the Wind TunnelAs you can see from the streamlines, the body of the new Passat is very aerodynamic. No turbulence, which increases aerodynamic drag, occurs. The new Passat has a drag coefficient of cd = 0.27, making it the best in its class. Accounting for the projected vehicle area (A) of 2.1 m2, aerodynamic drag is (Cd x A) = 0.567 m2.191/72A = 2.1 m2191/0210Fully-galvanised BodyFor the first time, the Passat has a fully galvanised body which comes with an 11-year anticorrosion perforation warranty. The drawing below shows you the parts which are hot-dip galvanised and those which are electrolytically galvanised. Surface patterns, which are also visible after painting, emerge during the hot-dip galvanisation process. That is why the outer skin of the body is electrolytically galvanised to produce a smooth finish.Electrolytically galvanised Hot-dip galvanised191/7011BodyStability and StructureThe Passat leads its class in terms of torsional rigidity. This was achieved by using: l high-strength panels l different panel thicknesses l improved adhesive bonding techniques (e.g. adhesive joints) Adhesive joints increase rigidity and leakproofing while minimising noise levels.12High-strength PanelsHigh-strength panels are used to produce a body with greater stability and strength and therefore to provide more safety for the vehicle occupants. They also substantially reduce the weight of the body-in-white. As you can see, the high-strength steel components in the front section of the vehicle create a cage-type structure to protect the vehicle occupants. The wings are also manufactured from highstrength steel. Advantages: - Less weight - Greater resistance to buckling - Higher strengthThe Rear Bumpers191/74Repairing damage to the rear bumpers previously involved expensive repair and welding work, even after minor accidents.191/61 191/46High-strength panels Adhesive joints Laser-welded Mash seam weldedThe bumpers on the Passat ‘97 have the capacity to absorb so much energy during a low-speed rear collision that only plastic parts have to be replaced. Time-consuming welding work is no longer necessary.13BodyBody PlatformThe floorpan assembly, side members and luggage compartment floor assembly were adopted from the Audi A4 as a platform. To enhance ride comfort for rear-seat passengers, a steel floor plate 86 mmwide was inserted.+86 mmNew parts in Passat ‘97191/6914Vehicle SafetyThe following features will be of interest to you: l Active and passive safety l ABS as standard l The Passat already complies with the new European standard for crashworthiness l Door module with enclosed subframe l Driver, front passenger and side airbags as standard l New seat belt tensioner with force limiter l Inside door panels with pelvis paddingsAs you will no doubt already know, we make a distinction between active and passive safety.Active safety Braking systemsPassive safety Airbag systemsSteeringRestraint systemsRunning gearInside door panels and side trims with integral pelvis paddingsSafety bodySteering column191/7515Vehicle SafetyCrashworthinessThe new Passat offers the driver and front passenger more safety, particularly during a side impact. The inside door panel, which is fitted complete with built-in door fittings, is bolted to the door. To protect the occupants, the inside door panel has an enclosed surface to prevent intrusion of the built-in door fittings into the interior of the vehicle.Inside door panel191/05Side impact beamThe side impact beams made of pressed sheet metal are arranged diagonally and glued to the outer panel to increase door rigidity. Impact energy can therefore be better absorbed, distributed and converted. Pelvis and rib paddings give the vehicle occupants added protection.Rib paddingsPelvis paddings191/07The size of the overlap between the door and the sill, columns and side section has been increased. Deformation strength is increased due to the larger contact surface.Overlap 16191/06Airbag SystemsIn addition to the driver and front passenger airbags, the Passat is equipped with side airbags as standard. Depending on the side and angle of impact, only the airbags in the immediate vicinity of the danger zone are inflated. Therefore, an uninflated airbag on the side facing away from the accident need not necessarily be defective. The driver and front passenger airbags, which have filling volumes of roughly 65 ltr. and 120 ltr. respectively, conform to the new international-standard airbag sizes. The volume of the standard side airbag is roughly 12 litres.60$60$60$191/04Side impact, left-hand sideDetected by: crash sensor located beneath the left-hand seat and a safety sensor integrated in the airbag control unitHead-on collisionDetected by: crash sensor and a safety sensor integrated in the airbag control unitSide impact, right-hand sideDetected by: crash sensor located beneath the right-hand seat and a safety sensor integrated in the airbag control unit 17Vehicle SafetyThe Seat Belt TensionerThe pyrotechnical seat belt tensioner, together with the “belt fastened” sensor and belt force limiter, are combined in a single assembly. This compact design greatly simplifies replacement. The “belt fastened” sensor prevents the seat belt tensioner from being activated when the seat belt is not worn.Seat belt tensionerBelt force limiter191/1718Engines and GearboxesIn addition to the six tried and tested engines listed below, the new VR5 unit will also be mounted in the Passat.1.6-ltr. Engine AHLDisplacement Compression ratio Max. torque Max. power output Engine management Fuel 1595 cc 10.3 : 1 140 Nm at 3800 rpm 74 kW at 5300 rpm Simos 2 95 RON unleaded premiumThis engine is also used in the Audi A3. It is mounted in the Passat without a twin-path intake manifold.191/851.8-ltr. 5V Engine ADRDisplacement Compression ratio Max. torque Max. power output Engine management Fuel 1781 cc 10.3 : 1 173 Nm at 3950 rpm 92 kW at 5800 rpm Motronic M 3.8.2 95 RON unleaded premiumThis engine is also used in the Audi A6.191/7719Engines and Gearboxes1.8-ltr. 5V Turbo Engine AEBDisplacement Compression ratio Max. torque Max. power output Engine management Fuel 1781cc 9.3 : 1 210 Nm at 1750-4600 rpm 110 kW at 5700 rpm Motronic M 3.8.2 95 RON unleaded premiumThis engine is also used in the Audi A4.191/312.8-ltr. V6 Engine ACKDisplacement Compression ratio Max. torque Max. power output Engine management Fuel 2771cc 10.3 : 1 280 Nm at 3200 rpm 142 kW at 6000 rpm Motronic M 3.8.2 98 RON unleaded premiumThis engine is also used in the Audi A6.191/32202.3-ltr. VR5 Engine AGZThe new VR5 engine has a displacement of 2.3 litres. It is derived from the VR6 engine and is designed for in-line or transverse mounting. Power output is 110 kW.191/53The engineering of the VR5 engine is explained in a separate Self Study Programme.21Engines and Gearboxes1.9-ltr. TDI Engine AHUDisplacement Compression ratio Max. torque Max. power output Fuel Mixture preparation 1896 cc 19.5 : 1 202 Nm at 1900 rpm 66 kW at 4000 rpm 45 CN diesel Direct injection with electronically controlled distributor injection pump191/281.9-ltr. TDI Engine AFNDisplacement Compression ratio Max. torque Max. power output Fuel Mixture preparation 1896 cc 19.5 : 1 235 Nm at 1900 rpm 81 kW at 4150 rpm 45 CN diesel Direct injection with electronically controlled distributor injection pumpThis engine features a variable-rate turbocharger. You will find further information on this engine in Self Study Programme SSP190.191/2822Range of Engines and GearboxesManual gearbox Engines Automatic gearbox012/01W1.6-ltr. 74kW01N1.8-ltr. 5V 92kW 1.8-ltr. 5V turbo 110kW 2.3-ltr. VR5 110kW 1.9-ltr. TDI 66kW 1.9-ltr. TDI 81kW 2.8-ltr. V6 5V 142kW 01V Syncro191/6401V01A23Engines and Gearboxes5-speed Manual Gearbox 012/01WThe 012/01W is a manual gearbox as used in the Audi A4. This gearbox has a magnesium housing for installation in the 1.6-ltr./74kW aluminium engine block.191/345-speed Manual Gearbox 01AThe 01A is the manual gearbox for four-wheel drive vehicles as used in the Audi A4.191/35244-speed Automatic Gearbox 01NThe 01N is also installed in the Audi A6, for example. You can find detailed information on this gearbox in Self Study Programe No. 172.191/365-speed Automatic Gearbox 01VYou will also be familiar with the 01V from the Audi A4. It is equipped with Tiptronic control as standard. You can find detailed information on this gearbox in Self Study Programme No. 180.191/7825Running GearIn addition to the four-link front suspension, we will show you on the following pages the newly developed torsion beam rear suspension as well as the new double-wishbone rear suspension unique to Syncro models.The Four-link Front SuspensionThe four-link front suspension is standard in all front- and four-wheel drive vehicles. In the case of vehicles with tripoid joints, these joints can be repaired.Tripoid joint191/3726The Torsion Beam Rear SuspensionAdvantages of torsion beam rear suspension: Larger through-loading width due to the fact that the coil springs and shock absorbers are kept physically apart Use of single-tube dampers Downward-facing V-section of axle beam Self-aligning twin-grooved oblique ball bearings act as wheel bearings-Single-tube damperCoil spring191/5527Running GearThe Double-wishbone Rear SuspensionThe double-wishbone rear suspension was developed in order to provide a through-loading width of over 1000 mm.191/54Engine power is transmitted to all four wheels by a Torsen differential.28BrakesThe Passat is equipped with the Bosch 5.3 antilock braking system as standard. Two different sizes of brake disc are available for the front axle. The rear suspensions also have disc brakes as standard.Disc brakes, frontDisc brakes, rear191/16191/14280 x 22 mm brake disc The front disc brakes are vented. The smaller disc diameter is based on a smaller vehicle mass and lower power output282.5 x 25 mm brake disc This disc brake is vented and larger in size.Rear brake caliper The Passat has rear disc brakes. The brake caliper is made of aluminium.29SteeringHeight and Reach Adjustment of Steering ColumnThe Passat is equipped with power steering. The steering column can be adjusted manually 50 mm fore and aft and 28 mm for height. The steering column is attached to the body by a mounting pedestal with sliding guide. A damper element located above the double universal joint prevents vibrations and noise from being transmitted to the body. A clamped connection links the steering column to the power steering gear.Mounting pedestal with sliding guide191/38Clamped connectionDamper elementDouble universal jointYou can find additional information on the steering in Self Study Programme SSP 167.30ElectricsThe following features will be of interest to you: l Decentralised vehicle electrical system l Dash panel insert l Gas discharge headlights l Washer jetsDecentralised Vehicle Electrical SystemAdvantages: The main feature of the decentralised vehicle electrical system is that the central electrics are subdivided into separate connector stations, relay carriers and fuse carriers. These submodules are arranged locally. This means that they are located close to the assemblies and functional units to which they belong. The functions of the “car” as an integrated system are divided up among several control units with specific tasks. Short wiring harnesses make cable connections easier to find and assign. The short cables achieve substantial weight savings. Test points can be assigned more easily. The components of the vehicle electrical system are well protected against moisture. The decentralised vehicle electrical system results in easier servicing.Example of the arrangement of control units ABS control unit Fuse carriers, located on side of dash panel Airbag control unit Master control for extended central locking system Engine control unit191/43Repair work on the vehicle electrical system may only be carried out using Wiring Harness Repair Kit VAS1978.31ElectricsDash panel insertThe following features will be of interest to you: l Electronic immobiliser integrated in dash panel insert l Capable of diagnosis l Can be encoded l Fuel gauge The dash panel insert is available in two versions which differ from one another in terms of the displays in the centre of the dash panel insert. In vehicles equipped with a navigation system, this display is complemented by the Auto Check System with a multi-function display. The immobiliser is an integral feature of the dash panel insert. However, the matching functions of the immobiliser have been left unchanged. Self-diagnosis: The diagnostic functions can be retrieved using address word “17”. Both instruments can be encoded. This means that the dash panel insert can be encoded depending on country and engine configuration. It is also possible to enter the current mileage when the dash panel insert is replaced.191/79Auto Check System with multi-function display32Fuel gaugeIn previous systems, the fuel gauge tended to fluctuate, e.g. when cornering. To counteract this, damping of the fuel gauge was increased using electronic devices. However, the drawback of this was that the fuel gauge took longer to display the correct fuel level after refueling.The new fuel gauge eliminates this drawback. If the ignition is switched off and fuel tank capacity increases by four litres or more, the new fuel level is recalculated and displayed straight after the ignition is restarted. If the ignition is switched on and the vehicle is stationary, the damping cuts out and the fuel level is displayed immediately.Do not refuel the vehicle with the ignition switched on.Fuel gauge when cornering (previously)Fuel gauge when cornering (today)Fuel gauge when refuelingDamping OnDamping Off191/5133ElectricsGas Discharge HeadlightsGas discharge headlights, which are integrated into the headlights, are available for the Passat as an option. However, the use of gas discharge technology is limited to the dipped beam headlight because it takes up to three seconds to achieve maximum luminous intensity. Therefore, H4 halogen lights will continue to be installed for the main beam headlight. Advantage of gas discharge headlights: - Greater luminous efficiency than conventional headlights - Better brightness distribution by virtue of a lens - Fog light is no longer necessary On acount of the greater danger of dazzling oncoming traffic, vehicles with gas discharge headlights are equipped with dynamic headlight range control. Consequently, the switch for the manual headlight range control is not required.Electronic Headlight Range Control This function gathers its information on body tilt angle relative to the vehicle axes from two sensors located inside the front and rear wheel housings on the left-hand side of vehicle.H4 halogen headlights1 LuxGas discharge headlights1 Lux050100150200250 m191/8034Fan Jet NozzleThe Passat features new fan jet nozzles for washing the windscreens.Advantages: Better fluid distribution over the entire surface of the windscreen Lower water consumption Better cleansing effect No adjustment requiredEngine bonnet191/82Installation from belowMode of operation For the sake of simplicity, the mode of operation can be compared to that of a garden hose when it is swung from side to side. Moving the garden hose quickly produces a fan jet. A nozzle insert for producing the pendulum jet is integrated in the spray nozzle. It ensures a fan jet. A heated version of the spray nozzle is also available.Fan-type jet with an opening angle of 45$ - 50$191/8135Extended SystemsVarious systems cater for ride comfort and ease of operation in the new Passat. The following features will be of interest to you: l Extended central locking system – Decentralised system concept l Heater/air-conditioning – Innovations in the air-conditioning l Navigation + communications – Preparation for mobile cellular phoneExtended Central Locking SystemThe extended central locking system is based on a decentralised system concept. It has a central control unit and a separate door control unit with a control panel for every door. Self-diagnosis: Diagnosis is initiated using the address word “46”.Extended central locking system with four door control units191/62Master control units. Located in front of driver´s seat. Front door control units Located on control panel on driver´s side Located on window lifter motor on front passenger side Rear door control units Located on window lifter motors (available only in combination with electric window lifters in rear doors)36Functions of the Extended Central Locking SystemThe master control unit assumes the following functionsCentral locking of boot lid Anti-theft warning system with “interior monitor” functionInterior light controlfiDiagnosis Address word „46”Radio remote controlInterface to vehicle electrical systemSlide/tilt sunroofCentral locking of rear doors (only in combination with mech. window lifters at rear)The door control units assume the following functionsCentral locking of doors, with Safe modeElectric window lifters with excess power limitationElectrically adjustable, folding and heated door mirrorsDiagnosis Address word „46”fi191/4537Extended SystemsThe heaterUnlike predecessor models, the new heater is constructed in one piece. The air distributing housing and the air duct with shutoff flap are combined in a single component. The heater, which is controlled at the air intake side, permits fresh-air and air-recirculation modes. A main shutoff flap is therefore no longer required.Fresh-air/air-recirculation flap191/27191/48Central flap-By virtue of the stepped form of the central flap, the central air vent is closed in defrost mode. An electric-motor-operated fresh-air/air-recirculation flap is integrated. In defrost mode, the air recycle function is switched off.38Pleasant air-conditioning for comfort and safety in the Passat.The CLIMAtronicOperating and display unit with control unitTemperature sensorCLIMAtronicAUT OECO N191/47-The controls have been rearranged. The temperature sensor dash panel and blower is integrated in the operating and display unit. The photosensor measures incident sunlight over a large area. There is greater sensitivity for controlling the interior climate. Average outflow temperature is registered by a transmitter.39Extended SystemsThe Air-conditioningFresh-air/air-recirculation flap Back pressure flap191/42Fresh-air blowerCentral flap--The fresh-air/air-recirculation flap is combined with the back pressure flap. Fresh-air blower with integrated control unit. The shape of the central flap has been modified to allow separate airflow to the central and side vents. All flaps are electic-motor-operated.The following components are integrated in the refrigeration circuit: - Plate evaporator - Controlled swash plate compressor - Condenser - Butterfly valve - Collecting vesselAir-conditioning without back pressure flap is installed in right-hand drive vehicles.40NavigationThe navigation system enables the driver to reach his (her) destination easily and safely. It replaces the road map and enhances road safety. This system employs a map stored on a CD-ROM. The driver can select his (her) destination on this map. Directions for the driver are then given on the display in the dash panel insert and via the loudspeaker built into the control unit. The system comprises the following elements: The navigation computer with integrated CD-ROM drive The control unit with control and loudspeaker The display integrated in the dash panel insert The earth magnetic field sensor ABS wheel speed sensor The sensor for the global positioning satellite system (GPS) The GPS satellite networkDisplay in dash panel insertEarth magnetic field sensor GPS sensor Navigation computerOperating unit191/66ABS wheel speed ssensor ABS-control unit41Extended SystemsNavigation computer with CD-ROM drive The navigation computer determines the position of the vehicle by means of the above-mentioned sensors. It then compares the calculated position with the map stored on the CD-ROM and the chosen destination. The computer then calculates directions for the driver from this comparison.191/50Control unit with control and loudspeaker The control unit is the interface to the navigation computer. The system is switched on or off and the destination is entered by operating the control. In addition to the display integrated in the dash panel insert, a voice output can also be provided by means of the built-in loudspeaker.191/49Display integrated in dash panel insert The navigation system displays information visually via the display of the Auto Check System with multifunction display integrated in the dash panel insert. Depending on selected function, the display shows a letter field for entering a destination or pictograms representing directions for the driver .191/8342ABS wheel speed sensor The wheel speed sensors of the rear suspension are used to provide the navigation computer with iinfomation on distance travelled.191/84Earth magnetic field sensor The earth magnetic field sensor determines the direction of travel relative to the north pole for the navigation computer.191/87GPS sensorBase of aerial191/88GPS stands for Global Positioning System, a global navigation system. The sensor is integrated in the roof aerial. The navigation computer uses the data supplied by the GPS sensor as a correction factor or when relocating the vehicle if the computer loses track of the current position (e.g. during rail transport).Connector GPS sensorHowever, this particular navigation system is not yet able to make allowance for traffic lights, one-way roads, building sites, traffic jams, etc.43Extended SystemsThe Passat is available with a mobile phone or cellular phone provision as equipment variants.Cellular Phone PreparationAdvantage: Easy to install No complex cable installation necessary One roof aerial for all functions Depending on equipment specification of the vehicle, three types of aerial can be installed: - Radio only - Radio and telephone - Radio, telephone and navigation (GPS) Scope of cellular phone provision: Hands-free microphone integrated in left-hand A pillar VDA-standard cable (standard connection for mobile phone) Radio mute function Change-over relay for left-hand door loudspeaker Combined roof aerial with high-frequency line to mobile phoneDiagnositic connection191/68With the cellular phone provision, only mobile phones with a VDA-standard connection can be operated.44Notes45Notes4647Service.192The Passat ‘97The EngineeringDesign and FunctionSelf Study ProgrammeFor internal use only. ¶ VOLKSWAGEN AG, Wolfsburg All rights reserved. Specifications subject to change. 640.2810.11.10 Technical status: 11/96 ` Printed on chlorine-free bleached cellulose paper.Service DepartmentThe Passat ‘97SSP 192/107Having provided you with an initial overview of the new Passat in the Self Study Programme entitled “The Passat ‘97 – The Presentation”, we now want to describe in detail how the car’s various components are designed and how they function.The subjects of the VR5 engine, convenience electronics and navigation system are so wideranging that it would be beyond the scope of this Self Study Programme. We will therefore deal with them separately.2PageIntroduction Vehicle Safety 1.8-ltr. 5V Engine ADR 1.8-ltr. 5V Turbo Engine AEB 2.8-ltr. V6 Engine ACK 1.9-ltr. TDI Engine AFN Gearbox Drive Shafts Running Gear ABS/EDL Electrics Air-conditioning04 06 20 22 26 34 38 40 43 48 55 60Important! / Note!New!This Self Study Programme is not a Workshop Manual! Please refer to the relevant Service Literature for all inspection, adjustment and repair instructions.3IntroductionOverview of topicsEngines Given that the engine concepts used in the Passat ‘97 are tried and tested, we will confine ourselves solely to special innovations such as the variable valve timing featured in the 2.8-ltr. V6 engine.Gearbox Non-ferrous metals, such as aluminium or magnesium, are being used increasingly in vehicle construction. In this booklet we will explain the advantages and special features of magnesium components.Electrics You will be given information regarding the gas discharge headlights.Drive shafts We will explain how length compensation works in the triple roller drive shafts.4ABS/EDL As a part of the ABS/EDL system, we will present you the new hydraulic unit with an integrated control unit.Running gear In addition to information about the torsion beam rear axle and the double wishbone rear axle, we will show you the new design of the new wheel bearing generation.SSP 192/001Air-conditioning The latest developments and the special features of the CLIMAtronic will be described.Vehicle safety We will describe the gradual action of the side airbag and the belt tensioner with belt force limiter.5Vehicle SafetyMode of operation of the restraint systemsTwo different restraint systems are used in the new Passat: l Seat belts with belt tensioner and belt force limiter, used on all outer seats, l Front and side airbags for the driver and front passenger.Integrated front airbagsSeat with integrated side airbagDoor lockBelt tensioner with belt force limiter SSP 192/047Airbag control unitCentral module of convenience central locking systemSide airbag crash sensor6Effect of the restraint systems during minor accidentsDuring minor accidents, the body only partially absorbs the impact energy of components such as bumpers and impact absorbers. belt tensioners restrain the car’s occupants in their seats. The belt force limiter reduces the risk of the belt causing injury. In this case, the airbags are not triggered.The seat belts provide adequate protection; theSSP 192/048 The belt tensioners are triggered mechanically on impact.7Vehicle safetyThe effect of the restraint systems during serious accidentsDuring serious accidents, the car body absorbs the impact energy. The passenger compartment remains by and large intact and the airbags are triggered. In addition to the protection afforded by the seat belts, the restraint systems protect the front passengers from more serious injuries in the upper body and head areas. The car’s central locking system is opened.Airbags are triggered.Central locking system is opened.SSP 192/049The belt tensioners are triggered mechanically on impact.Airbag control unitCentral module of convenience central locking systemSide airbag crash sensorIN OUT8Side airbagThe new side airbag system is integrated in the driver’s and front passenger’s seats. The side airbag is described as a thorax airbag. It mainly protects the thorax, and with it the lungs and pelvis, from lateral bruising. In terms of its appearance, the new airbag control unit has a different connector housing code to the previous model.Side airbag (illustrated as triggered)Airbag control unit J234Connection SSP 192/006 Crash-sensor G179When carrying out work on the airbag systems, always follow the instructions given in the Workshop Manuals.9Vehicle safetySide airbag design The side airbags are integrated in the front seat backrests. The folded airbag and gas generator are accommodated inside the plastic housing. When the side airbag is triggered, the gas cartridges in the gas generator are opened and the pyrotechnical charge ignites. The highly pressurised gas contained inside the cartridge expands instantaneously, inflating the airbag. While expanding, the gas cools and mixes with the hot gas of the pyrotechnical charge. The temperature of the gas mixture is therefore so low that there is no risk of burning. The side airbag has a capacity of approx. 12 litres.HousingSSP 192/005Air bagGas generator with gas cartridge and pyrotechnical charge10A two-stage crash recognition system is used to ensure reliable side airbag activation.Crash sensors G179/G180 The crash sensors for the side airbags are located below the two front seats on the seat cross members. They are conditioned to respond to lateral force application. The crash sensors are known as intelligent sensors. They operate independently of each other.SSP 192/070In addition to an electronic acceleration sensor, the entire electronics are integrated in the sensor housing. When a sensor recognises a crash, it sends a signal to the airbag control unit.When an impact occurs, the crash sensor G179 informs the airbag control unit that it has recognised a crash.SSP 192/11911Vehicle safetyAirbag control unit J234 In parallel to the crash sensors, sensors in the airbag control unit evaluate the severity of the crash. The relevant side airbag is not triggered until these sensors have also rcognised that an accident has occurred and a crash sensor sends an airbag trigger request. The two crash sensors below the front seats perform a function check at regular intervals, providing feedback to the airbag control unit. The system status of the side airbags can be displayed via the self-diagnosis. The airbag control unit also indicates when a fault may possibly have occurred in the crash sensors or the side airbags via the airbag warning lamp. There is an additional energy storage device in the airbag control unit for igniting the side airbags. If the power supply fails during an accident, this energy storage device has sufficient energy to power the control unit and, if necessary, to ignite the airbags.Self-diagnosis: The self-diagnosis is started using address word “15”.The side airbag is triggered by the airbag control unit.The sensors in the control unit have recognised an accident in addition to crash sensor G178. SSP 192/12012Belt tensionerThe pyrotechnical belt tensioner combines with the force limiter and the seat belt recognition device in a single unit. It is only triggered if the mechanical seat belt fastened recognition system recognises an unreeled belt. Its compact design makes for much easier replacement. When an impact occurs, the belt tensioners reel in the belt and thus take up any slack (clearance between belt and body). The mode of operation of the belt tensioner is very different to that of its predecessors.There are two belt tensioner variants: l A ball-driven belt tensioner, used on the front seats. l Belt tensioners operating according to the same principle as the Wankel engine, used on the rear seats.Front belt tensionerPropellant charge Trigger unit BeltBall retainerFeed tube containing ballsGearwheel SSP 192/126 13Vehicle safetyFunctional description of front belt tensionerThe belt tensioner is activated by balls mounted in a feed tube.Mechanical trigger unitPropellant charge BeltFeed tube SSP 192/124When the belt tensioner is triggered, a pyrotechnical propellant charge ignites. It sets the balls in motion and drives them into the ball retainer via a gearwheel. The belt reeling device is driven by the kinetic energy of the balls, thus reeling in the belt.Belt reeling deviceGearwheel SSP 192/125Ball retainer14Rear belt tensionerThe belt tensioner can be described in simpler terms as a “pyrotechnical Wankel engine”. This “Wankel engine” is driven by 3 propellant charges. They are ignited in succession.Belt tensioner triggering mechanismBeltLocking mechanism with child safety seat lockBelt force limiterSSP 192/066Reeling mechanismBelt tensioner15Vehicle safetyFunctional description of rear belt tensioner.SSP 192/009The first propellant charge is ignited by a mechanical triggering device.Mech. triggering device Wankel rotor Firing pin Propellant chargeThe released gas causes the rotor to rotate. The belt is tightened. After a certain angle of rotation, the piston opens the inlet port of the second firing pin, thus igniting the second propellant charge.SSP 192/010The released gas makes the rotor rotate until the next inlet channel is opened. The third charge ignites.SSP 192/011The belt tensioner is able to perform approximately two full turns in this way.SSP 192/012 16Belt force limiterFunctional description of belt force limiter If, due to acceleration, the tensile force of the belt is so high that bruising or internal injuries can occur, the tensile force of the belt must be limited to a tolerable level. It is limited by the belt reeling device torsion shaft. The torsion shaft operates in much the same way as a spring. Depending on its tensile force, the belt “gives”. Both types of belt tensioner use the same systemBeltBelt reeling device The end of the slot limits the distance which the reeling device can “give”. The torsion shaft is connected to the gearwheel on this side.The reeling device is able to rotate freely within gearwheel inner race.SSP 192/065The torsion shaft is connected to the reeling device on this side.The torsion shaft runs through the belt reeling device.17Test your knowledge1. Which components belong to the restraint system of the Passat ‘97?2. The side airbag has a capacity ofa) 8 litres, b) 12 litres or c) 15 litres.3. The side airbag crash sensors respond to the application of ................................. force.4. What is the function of the belt force limiter?185. The rear belt tensionera) operates according to the Wankel engine principle, b) uses a diaphragm pump, c) is ball-activated.6. Annotate the following drawing.d) a) e) b)f)c)SSP 192/126191.8-ltr. 5V Engine ADROn the following page, we will show you the new technical features of the 1.8-ltr. 5V engine, 1.8-ltr. 5V turbo, 2.8-ltr. V6 and TDI engines.Twin path intake manifoldThe 1.8-ltr. 5V engine has a twin path intake manifold. The twin path intake manifold is designed so that it is possible to switch between long and short intake paths. Long intake path A long intake path permite optimum charging of the cylinder, and consequently high torque, in the low speed range. Short intake path Switching over to the short intake manifold permits high power output in the upper speed range.Twin path intake manifoldSSP 192/085Vacuum unit20Engine control unit J220The engine control unit sends a signal to the intake manifold pressure change valve. It uses the vacuum unit to change over the intake manifold. Power is supplied via the fuel pump relay.IIntake manifold pressure change valve N156Vacuum unit SSP 192/127Electric circuitComponents J17 J220 N156 S Fuel pump relay Motronic control unit Intake manifold pressure change valve Fuse30 15 X 31J1730 15 X 31SN156 64 J220 2IN OUT43SSP 192/106 211.8-ltr. 5V Turbo Engine AEBThe 1.8-ltr. 5V turbo engine is equipped with the Motronic M 3.8.2 engine management system.System overviewSensors Lambda probe G39 Air mass meter G70 Actuators Fuel pump G6 with fuel pump relay J17 Injection valves N30, N31, N32, N33Intake manifold temperature sender G72 Knock sensors G61 + G66Engine control unit J220Output stage N122Ignition coils N, N128, N158, N163 Hall sender G40 Throttle valve control unit J338Engine speed sender G28 Coolant temperature sender G62 Altitude sender F96 Throttle valve control valve J338Activated charcoal filter system solenoid valve N80Charge pressure limitation solenoid valve N75Additional signalsAdditional signalsImmobiliser control unit J362 22Diagnostic connection SSP 192/074Function diagram 1.8-ltr. 5V turbo engine AEBComponents F96 G6 G28 G39 G40 G61 G62 G66 G70 G72 J17 J220 J338 N N30 N31 N32 N33 N75 N80 N122 N128 N158 N163 S Altitude sender Fuel pump Engine speed sender Lambda probe Hall sender Knock sensor I Coolant temperature sender Knock sensor II Air mass meter Intake manifold temperature sender Fuel pump relay Control unit for Motronic Throttle valve control unitAdditional signals Pin 5 Pin 6 Pin 7 Pin 8 Pin 18 Pin 20 Pin 22 Pin 23 Pin 49 Actual engine torque (out) Speed signal (out) Throttle valve potentiometer signal (out) Air-conditioner compressor signal (in + out) Fuel consumption signal (out) Road speed signal (in) Gear engaged signal for automatic gearbox (in) Auto. gearbox CU retard signal to engine CU (in) Upshift/downshift signal for automatic gearbox (in)Ignition coil Injection valve, cylinder 1 Injection valve, cylinder 2 Injection valve, cylinder 3 Injection valve, cylinder 4 Charge pressure limitation solenoid valve Activated charcoal system solenoid valve Output stage Ignition coil 2 Ignition coil 3 Ignition coil 4 Colour code Fuse Input signal Output signal Positive Negative2330 15 X 31 J17N SINOUTN80 15 50 50N75 64 50 50N33N32 65 50N31 58N30 80 73 50 4 3 1 50 50 J220 50505050 27 2550 26 12 13 2 68 60 56 63 53 54 6750G6G39G70G61G66G28G62G72J332430 15 X 31N128N158N163N122 77 50 50 78 50 70 5 6 7 8 18 20 22 23 49 1950 59 69 7550 115050 74 76 6250 61F96 G40SSP 192/076252.8-ltr. V6 Engine ACKVariable valve timingIt provides high torque when driving in low gears at low speeds, thus improving fuel economy and reducing exhaust emissions. High output is needed at high speeds. To achieve both, the cylinder must be well-filled in all speed ranges.Injection valve closes earlyAt low speeds, the piston moves so slowly that the gas mixture in the intake manifold follows the movement of the piston. The inlet valve must be closed early so that the fuel-air mixture is not forced back into the intake manifold.SSP 192/130 Injection valve closes lateAt high speeds, the flow rate inside the intake manifold is so high that the mixture can continue to flow into the cylinder although the piston is moving back up. The inlet valve is closed when the fuel-air mixture can no longer enter the cylinder. In engines with variable valve timing, the closing times of the inlet valve are adapted to the speed range.SSP 192/13126The principle of variable valve timing:The exhaust camshaft is driven by the crankshaft by means of a toothed belt. The inlet camshaft is driven by the exhaust camshaft by means of a chain.With variable valve timing, the opening times of the inlet valves are adjusted depending on engine speed. The drive chain therefore turns the inlet camshaft.Exhaust camshaftInlet camshaftPerformance position In the “Performance” position, the lower section of the chain is short while the upper one is long. The inlet valve closes late. The rapid air flow within the intake manifold ensures that the cylinder charge is high. The engine is thus able to develop high output at high speeds.SSP 192/081 Variable valve timerTorque position Moving the variable valve timer down shortens the upper chain section and lengthens the lower one. The inlet camshafts therefore rotate in relation to the exhaust camshaft. The exhaust camshaft cannot rotate at the same time, since it is restrained by the toothed belt. The inlet valve closes early. In this position, high torque is produced in the lower and medium speed ranges.SSP 192/080272.8-ltr. V6 Engine ACKVariable valve timerA hydraulic cylinder lifts and lowers the variable valve timer. Oil is supplied to the hydraulic cylinder via the engine oil circuit. The engine control unit controls the hydraulic cylinder via the variable valve timing valve, which is bolted directly to the variable valve timer housing.Exhaust camshaftBank1, variable valve timing valve N205Hydraulic cylinder Inlet camshaftVariable valve timer with integrated chain tensionerSSP 192/10828Variable valve timing in the V6 engineExhaust camshaft Inlet camshaftThe design of the V6 engine makes particularly heavy demands on variable valve timing. Viewed from above, the exhaust camshafts are arranged on the outside and the inlet camshafts on the inside. As a result, the variable valve timers of the left and right bank of cylinders have to operate in opposite directions.SSP 192/129Idling When the engine is idling, the inlet valves are closed late.SSP 192/103Torque position The inlet valves are closed early above an engine speed of 1000 rpm. The camshaft adjuster of the left bank of cylinders moves down while the right cylinder bank variable valve timer moves up.SSP 192/104Performance position At a speed of 3700 rpm, the inlet valves are closed late.SSP 192/103292.8-ltr. V6 Engine ACKThe 2.8-ltr. V6 engine is equipped with variable valve timing and is controlled by the Motronic M 3.8.2 engine control unit.System overviewSensors Lambda probes I+II G39 + G108 Air mass meter G70ActuatorsFuel pump G6 with fuel pump relay J17Ignition transformer N152 Injectors N30, N31, N32, N33, N83, N84 Throttle valve control unit J338Sensor for intake manifold temperature G72 Knock sensors G61 + G66Engine control unit J220Engine speed sender G28Intake manifold pressure change solenoid valve N156 Activated charcoal filter system solenoid valve N80Hall sender G40 Hall sender II G163 Coolant temperature sender G62Bank1, variable valve timing N205Throttle valve control unit J338Bank2, variable valve timing N208Additional signalsAdditional signalsImmobiliser control unit J362 30Diagnostic connection SSP 192/073Function diagram of 2.8-ltr. 6V Engine ACKComponents G6 G28 G39 G40 G61 G62 G66 G70 G72 G108 G163 J17 J220 J338 N N30 N31 N32 N33 N83 N84 N75 valve N80 valve N152 N156 N205 N208 S Fuel pump Engine speed sender Lambda probe Hall sender Knock sensor I Coolant temperature sender Knock sensor II Air mass meter Intake manifold temperature sender Lambda probe II Hall sender II Fuel pump relay Motronic control unit Throttle valve control unit Ignition coil Injection valve, cylinder 1 Injection valve, cylinder 2 Injection valve, cylinder 3 Injection valve, cylinder 4 Injection valve, cylinder 5 Injection valve, cylinder 6 Charge pressure limitation solenoid Activated charcoal system solenoid Ignition transformer Twin path intake manifold valve Camshaft adjustment valve I Camshaft adjustment valve II FuseAdditional signals Pin 5 Pin 6 Pin 7 Pin 8 Pin 18 Pin 20 Pin 22 Pin 23 Pin 45 Pin 49 Actual engine torque (out) Speed signal (out) Throttle valve potentiometer signal (out) Air-conditioner compressor signal (in + out) Fuel consumption signal (out) Road speed signal (in) Gear engaged signal for automatic gearbox (in) Aut. gearbox CU retard signal for engine CU (in) ABS signal (in) Upshift/downshift information for automatic gearbox (in)Colour code Input signal Output signal Positive Earth3130 15 X 31 J17SSSN80 15 50 50 50N156 64 50N205 55 50N208N84N83 79 50N33 72N32 N31 N30 65 58 50 50 80 73 50 50 4 3 50505050 2550 2650 3950 4050 4450 1150 7650 6850 60G6G39G108G40G163G61G663230 15 X 31G70 N152 12 50 0 50 3 56 50 53 50 54 50 67 50 66 59 69 75 62 74 14 2 19 13 70 71 78 5 6 7 8 18 20 22 23 45 498G62G72J338INOUTSSP 192/075331.9-ltr. TDI Engine AFNRadiator fan run-onA radiator fan run-on facility controlled by the engine management system is being used in the 1.9-ltr. 81kW TDI engine for the first time. The advantage of this is that the radiator fan run-on time is variable and can consequently be adapted to the previous operating conditions and load conditions of the engine.The run-on time is determined by the engine control unit via a characteristic map. Allowance is also made for the coolant temperature and engine load during the final minutes of car operation before the engine is turned off.Radiator fan run-on relay J397Self-diagnosis Open circuit /short circuit to earth Short circuit to positiveThe radiator fan run-on relay J397 is designated as blower relay J323 in the self-diagnosis.Electric circuit Components J248 J397 Diesel direct injection system control unit Cooling fan run-on relay Series resistor for coolant fan Fuse Coolant fan30 15 X 3130 15 X 31INOUTSN39J397S V7N39 3V7 J24834SSP 192/086Test your knowledge1. Which of the following diagrams represents the “Performance” position and the “Torque” position in the 2.8-ltr. V6 engine?a)b)2. Complete the following text.At low speeds, the piston moves so that the gas mixture inb)a),follows the movement of the piston. The inlet valve c) so that the fuel-air mixture is not forced back into the intake manifold. At high speeds, the flow rate in the intake manifold is so that the mixturee) d), ,although the piston is moving back up. The inlet valve is notf),until the fuel-air mixture can no longer enter the cylinder.35GearboxMagnesiumLightweight construction now plays a central role in vehicle development, due to the tough demands on performance, safety and fuel economy. Weighing roughly 34% less than aluminium, magnesium is, as a material, well-suited to meeting these demands. We will show you the advantages and impacts of magnesium using the 5-speed manual gearbox housing 012/01W. Density comparison Iron: 7.873 g/cm3 Aluminium: 2.699 g/cm3 Magnesium: 1.738 g/cm3The strength of a material depends on its density, among other things. Low density goes hand in hand with low strength. This loss of strength has to be compensated for somehow.The housing is therefore ribbed more intensively and the wall thickness has been increased. As a result, the magnesium housing actually weighs 27% less than the aluminium housing. Bolt insertion depth has also been increased.Comparison of insertion depths between magnesium, aluminium and iron36SSP 192/058SSP 192/059SSP 192/060Electrochemical voltage series In the presence of water, an electric current develops between two different metals. The car battery operates according to a similar principle. The electric current causes one of the two metals to decompose. If a metal decomposes easily, it is termed a non-precious metal. If a metal does not decompose easily, it is termed a precious metal. An electrochemical voltage series is produced by arranging the metals in a series extending from non-precious metal to precious metal. The further the metals in the voltage series are apart from one another, the higher the current and the more readily the less precious metals decompose.Excerpt from electrochemical voltage seriesAluminiumIronLeadCopperGoldH2OAlFePbCuAuMagnesiumSSP 192/09637GearboxMagnesiumContact corrosion, using a bolted connection as an example In this example, a magnesium component is attached using a bolt made is an iron alloy. If the contact surface is wetted with water, an electric current occurs between the two metals. This leads to contact corrosion. The magnesium is decomposed at the same time.WaterSSP 192/097 CorrosionWaterContact corrosion can be prevented by inhibiting the electric current between the two metals by coating the bolt with an insulating layer. This insulating layer is composed of a special non-conductive coating.SSP 192/061 Special coatingA special coating is applied to all add-on parts which come into direct contact with magnesium. Please follow the instructions given in the Workshop Manual.38Test your knowledge1. What is the insertion depth for magnesium compared to that for iron?a) 2.0 times greater, b) 5.2 times greater, c) 2.5 times greater.2. Assign the metals of gold, iron, magnesium, copper, aluminium and lead to the following drawing.a)b)c)d)e)f)39Drive shaftsTriple roller constant velocity jointThe triple roller CV joint reduces the transmission of vibrations and noise from the engine/ gearbox unit to the body. Triple roller joints are principally used in diesel and automatic cars. This is necessary due to the high vibrations which occur in diesel engines and the pretensioning forces which occur in automatic drive trains.CV ball jointTriple roller jointSSP 192/056DesignThe triple roller joint has three spherical journals with a roller fitted to each of them. The rollers are located in races and can slide and swivel on the tripod star.Race SSP 192/071Tripod starRoller HousingDrive shaft 40Function The principal task of the drive shafts is to transmit power from the gearbox to the wheels. They are also responsible for length compensation.The engine/gearbox unit runs in elastic bearings. At certain speeds, the unit begins to oscillate in its mountings.Triple roller joints SSP 192/041 Race Triple roller joint pin Drive shaftMoving parts Stationary partsThis movement is compensated by the triple roller joints, whereby the tripod star, together with the rollers, slide within their races.SSP 192/042RollerThe triple roller joint housing is pushed over the tripod star rollers by the movement of the engine/ gearbox unit. The drive shaft remains stationary in the process.SSP 192/043 41drive shaftsIn addition to the vibrations of the engine/gearbox unit, the triple roller joints have to equalise wheel bump and rebound.SSP 192/044The joint housing remains stationary in the process.HousingSSP 192/045The drive shaft is moved away from the gearbox by the rebound action of the wheels. At the same time, the rollers are displaced in only one plane within their races, thereby reducing friction and noise transmission to the body.SSP 192/046 42Running GearThe following pages describe the design modifications to the axles of the Passat ‘97 as presented to you in Self Study Programme SSP 191.Torsion beam rear axleThe anti-roll bar used in the new torsion beam rear axle is located in front of the axis of rotation. The rear axle mountings are located on the far outer side of the axle. This considerably reduces the forces acting on the rear axle mountings. The mounting housing is made of aluminium and bolted to the trailing arms. When designing the rear axle, comfort was a major consideration. The rear axle mountings and the large rubber bases of the coil springs minimise noise transmission from the axle to the body.Rubber baseTrailing armrAxis of rotationAnti-roll barRear axle mounting SSP 192/100On axles where the rear axle mounting is located on the inside, the mountings have to absorb large forces when cornering.Long lever arm SSP 192/111 Rear axle mountingLocating the rear axle mountings on the outside makes the lever arms shorter, with the result that the mountings only absorb smaller forces. They can therefore be designed with a softer rating.Short lever arm SSP 192/11243Running GearV section of torsion beam rear axleConventional rear axles have a V section which is open facing forward. In this configuration, the shear centre of the axle is located behind the V section. The centre of rotation is an imaginary axis about which the axle rotates when the suspension experiences a bump on one side. If the shear centre is behind the V section, then diagonally aligned track-correcting mountings have to be used to achieve a self-steering effect.Centre of rotationSSP 192/117SSP 192/116Shear centreThe new torsion beam rear axle has a V section which is open downwards. The shear centre is located above the V section. The axle has different rotational characteristics as a result.SSP 192/114SSP 192/134When cornering, the inside and outside cornering wheels go through rebound and bump respectively, because the car body tilts to the outside. The axle is twisted in itself. The bumped wheel adopts the toe-in position, while the rebound wheel adopts the toe-out position.Toe-outToe-inV section of rear axle is twisted when cornering.SSP 192/11844Hub/wheel bearing unitThe newly developed wheel bearing generation is used on the rear axle of front-wheel-drive vehicles. The twin-tracked ball bearing has a stationary outer race which is bolted to the rear axle mounting plate. The bearing inner race serves as the carrier for the brake disc and wheel. This design eliminates the need for an axle pivot. The ABS speed sensor is inserted into the wheel bearing and secured with a clip to prevent it from falling out. The advantages of the new wheel bearing generation are as follows: l Minimal wear due to improved sealing. l The rotor is protected by the inserted speed sensor and cannot be damaged by external influences. l The wheel bearing does not have to be adjusted any longer because the bearing preload is predetermined by its design.Speed sensor rotor Outer raceSpeed sensorInner race SSP 192/05745Running GearDouble wishbone rear axleThe newly developed double wishbone rear axle allows the same through-loading width as the torsion beam rear axle. It has an enclosed subframe to which the transverse links are attached. The subframe is connected to the body by four large bonded rubber mountings.Bonded rubber mountingEnclosed subframeSSP 192/098Single-tube gas-filled shock absorbers are used on the double wishbone rear axle. Their diameter is smaller than that of twin-tube shock absorbers. The low-lying position of the upper wishbone and the smaller shock absorber diameter permit a lower loading platform and a larger through-loading width.Upper wishboneLowerwishbonekSSP 192/09946Test your knowledge1. How is the high transverse rigidity of the torsion beam rear axle achieved? a) b)2. The V section of the new torsion beam rear axle is open.3. The advantages of the new wheel bearing generation are as follows:a) Minimal wear, b) The ABS speed sensor rotor is protected, c) It is self-adjusting, d) It has to be adjusted using a hexagon nut.4. On the double wishbone rear axle, the upper wishbone is located the wheel. As a result of this, is achieved.47ABS/EDLThe anti-lock braking system is a 4-channel system. This means that two valves are assigned to each wheel (inlet and outlet valves). The hydraulic unit and the ABS control unit are combined in a single module and can only be renewed as one unit. A Self Study Programme relating to the ABS 5.3 system is in preparation.System overviewSensorsABS/EDL control unit J104ActuatorsABS recirculating pump V39Front left + right speed sensor G45/G47Rear left + right speed sensor G44/46Hydraulic unit with solenoid valves N99-102/ N133-136 N166-168 ABS warning lampBrake light switch FBraking system warning lampAdditional signals, e.g. time signalAdditional signals Diagnostic connection SSP 192/06248ABS/EDL hydraulic unitConnection for:Diaphragm outlet damperFront left brake caliperFront right brake caliperBrake master cylinder Secondary piston circuit Brake master cylinder Primary piston circuitRear left brake caliperRear right brake caliperHydraulic blockRecirculating pumpSSP 192/063Features of hydraulic unit: One-piece cast iron housing. ABS/EDL solenoid valves each with two hydraulic connections and operating positions. Noise-optimised recirculating pump, Accumulator size for each brake circuit: approx. 3 cm3, Two diaphragm outlet dampers are connected upstream of the EDL hydraulic blocks. They help improve the low-temperature performance of the EDL control system.49ABS/EDLABS/EDL control unitABS/EDL control unit J104Features of control unit: Redundant computer concept with separate watchdog, Self-diagnosis capability, 26-pin connector contact.SSP 192/064Redundant computer concept In this case, redundant stands for a computer concept with several backups. In the control unit there are two computers which work with the same program independently and check one another. The two computers are, in turn, monitored by a third computer which assumes the task of controlling the solenoid valve relays. This third computer is known as the watchdog. If it detects a fault, it stores the fault message in a read-only memory and can be read out during the self-diagnosis. The fault is indicated by the ABS warning lamp.50ABS speed sensorSpeed sensor Speed sensor rotor Features of speed sensor: It is inserted into the wheel bearing and is thus protected against external influences. It generates signals contactlessly.-Signal utilisation The signal supplied by the ABS speed sensor is used to control the anti-lock braking system. The navigation system calculates the distance travelled from this signal.SSP 192/057Effect of signal failure Rotor The ABS system is switched off and the ABS warning lamp comes on. The navigation system is de-energised. The brake warning lamp comes on.This is how it works: The rotor is integrated and the speed sensor inserted in the wheel bearing. The speed sensor comprises a permanent magnet with two pole plates. A coil is wound around the pole platesand the permanent magnet. When the wheel moves, the rotor rotates about the speed sensor. In the process, it cuts the field lines of the pole plates, thus inducing a voltage in the coil. This voltage serves as the signal for the ABS control unit and the navigation system.Pole plateSSP 192/132Permanent magnet Coil Pole plate51ABS/EDLFunction diagramComponents F G44 G45 G46 G47 Brake light switch Rear right speed sensor 4 Front right speed sensor 2 Rear left speed sensor 3 Front left speed sensor 130 15 X 31J104 J105 J106 J220 J285 J401Control unit for ABS with EDL ABS recirculating pump relay Solenoid valve relay Control unit for Motronic Control unit with display unit in dash panel insert Control unit for navigation system with CD-ROM drive ABS warning lamp Front right ABS inlet valve Front right ABS outlet valve Front left ABS inlet valve Front left ABS outlet valve Rear right ABS inlet valve Rear left ABS inlet valve Rear right ABS outlet valve Rear left ABS outlet valve Front right EDL switchover valve Front right EDL outlet valve Front left EDL switchover valve Front left EDL outlet valve Fuse ABS recirculating pumpSS151718 N99 N100 N101K 47 N99 N100 N101 N102 N133 N134 N135 N136 N166 N167 N167 N168 S V39J106V39 16J105 3 1Colour code Input signal Output signal Positive EarthINOUTG445230 15 X 31N102N133N134N135N136N166N167N168N169J104549876192324132110141145G46G47J401J220K47J285FSSP 192/08753Test your knowledge1. How do you distinguish the ABS/EDL hydraulic unit from an ABS hydraulic unit?a) By the diaphragm outlet damper, b) By the colour of the control unit, c) By the threaded holes for the master brake cylinder.2. Where is the rotor for the speed sensor of the torsion beam rear axle located?3. Name the components in this system overview.a)e)b) f)c) g) d) h)k)54ElectricsGas discharge lampIn the case of gas discharge lamps, light is generated by an electric arc between two electrodes in a pea-sized gas-filled glass tube. The lamp emits light with high green and blue components due to the composition of the gas in the lamp tube. This is the external distinguishing feature of gas discharge technology. The advantages of this new headlight generation over conventional lamp technology are as follows:ElectrodeElectric arcGlass tubewith gas fillingElectrodeSSP 192/121l Up to three times higher luminous efficiency, same power consumption. A 35W gas discharge lamp is sufficient to provide twice the illumination of a 55W lamp. l The useful life of approx. 2500 hours is several times that of the halogen lamp.l The special design of the reflector, aperture and lens provides a much longer range and a wider near-field scatter zone. This illuminates the roadside better, thus reducing driver eye fatigue. l Fog lights are not needed due to the wide near-field beam.55ElectricsThe gas discharge lamp requires a high-voltage pulse of several thousand volts to ignite the electric arc. The voltage is produced in the ballast. After ignition, an increased electric current is applied to the gas discharge lamp for approx. 3 seconds. As a result, the lamp achieves its maximum brightness with a minimum delay of 0.3 seconds. This slight delay is also the reason why the main headlight is still equipped with a halogen lamp which is connected to the headlight as required. Once the gas discharge lamp has reached its nominal brightness, the ballast regulates the lamp power output tio the lamp.Gas discharge lampSSP 192/122Gas discharge headlightA gas discharge headlight comprises: l headlight housing, l gas discharge lamp ballast J426/J427 and l headlight range control actuator V48/V49.BallastSSP 192/078 Electrical connection Headlight range control actuatorA repair solution is available for the headlight housing. During minor accidents, the securing pin on the headlight housing can shear off. With regard to the gas discharge headlight, this may result in disproportionately high repair costs. Our repair solution, which involves renewing the securing pin and eccentric, allows all headlight housings to be renewed inexpensively.56Automatic headlight range controlTo prevent dazz