TECHNICAL DOCUMENTATION

SSP 195 The 2.3-ltr V5 Engine

PDFEN40 pages2 MB
SSP 195 The 2.3-ltr V5 Engine - PDF cover

This PDF is currently unavailable.

Read document text
The 2.3-ltr. V5 EngineDesign and FunctionSelf-Study Programme No. 195 195_118The new 2.3-ltr. V5 engine is related to the VR6 engine as regards design. For this reason this Self-Study Programme will be largely confined to the modifications to the VR6 engine.You will find more detailed information about the design of the engine mechanicals or the cooling system and the oil circuit in SSP 127 “The VR6 engine” and SSP 174 “Modifications to the VR6 engine”.NewImportant NoteThe Self-Study Programme is not a Workshop Manual! 2Please always refer to the Service Literature for all inspection, adjustment and repair instructions. The contents of this SSP at a glanceIntroduction 4Engine mechanicals6Power transmission11Motronic injection and ignition system14Function diagram32Service34Self-diagnosis363 IntroductionWhy do V-engines exist?Front-wheel drive, in combination with a transversely mounted four-cylinder inline engine, is now part and parcel of many motor vehicle concepts. Installing the engine transversely has promoted the development of more compact vehicles. But the vehicle width is not sufficient to accommodate inline engines with more than four cylinders. This is why the V-engine came into being. Al-though V-engines have a very short overall length, they are rather wide - with a V-angle of 60° or 90° - and hence cannot be used in smaller mid-range vehicles. V-engine with an angle of 15° The VR engines and the new V5 engine combine the advantages of the V-concept with the advantages of the inline engine. These are: l short overall length thanks to V-angle, l small overall width thanks to the V-angle of 15°, l only one cylinder head is required,The V5 was derived from the VR6 by removing the 1st cylinder from the latter. The resulting, even more compact design makes it possible to use this powerful unit in all vehicle classes.195_0854 Technical specificationsEngine code V-angle Displacement Bore Stroke Compression ratio Firing order Mixture preparation and ignition Fuel Exhaust gas aftertreatment AGZ 15° 2324 cm3 81.0 mm 90.2 mm 10.0 : 1 1-2-4-5-3 Bosch Motronic M3.8.3 95 RON unleaded premium Three-way catalytic converter with lambda controlThe V5 engine conforms to exhaust gas level D3.Torque [Nm]Power [kW]As the power vs. torque curve shows, the remarkable features of this engine are its immense low-end torque and high power output in the upper rpm range. Max. torque is 220 Nm at 3600 rpm and max. power output is 110 kW at 6000 rpm.TorquePower195_084Engine speed [rpm]5 Engine mechanicalsOffsettingTo give you a better understanding of the design features of the V5 engine and to clarify several technical concepts, we will begin by looking at the design features of the inline engine.Inline engine In the inline engine the piston is located directly above the centre of the crankshaft. The piston stroke (h) is therefore twice the crank radius (2xr). TDC and BDC are exactly 180° apart.Con rod bearing cyl. 1 TDC h BDC rCentre of crankshaftCentrifugal mass195_074195_079V-engine with an angle of 90° In conventional V-engines the pistons in both banks of cylinders are aligned at 60° or 90° to one another. The centre lines of the cylinders nevertheless project through the centre of the crankshaft. The piston stroke is then twice the crank radius in this case, too. But the large V-angle also means the engine has a large overall width.Cy li ax nde is rrCentre of crankshafth195_0756 V5 engine with an angle of 15° As a result of the V-angle of 15°, the V5 engine is not as wide as engines with an angle of 60° or 90°. The V5 engine can be mounted both longitudinally and transversely because it is shorter than an inline engine.Centre line of crankshaftCentre line of cylinderSeveral difficulties had to be overcome during the design process, since the 15° V-angle causes the cylinders to overlap at the bottom.Centre line of crankshaft195_109195_076To avoid these overlaps, it was necessary to shift the cylinders slightly further outwards so as to increase the clearance between the cylinders. This process is known as “offsetting“. In the V5 engine the offset of each bank of cylinders is 12.5 mm. By offsetting the cylinders, their centrelines no longer project through the centre of the crankshaft. As a result, the pistons travel i na different line from TDC to BDC than from BDC to TDC. Allowance has to be made for this difference when designing the crankpin throw to ensure that all cylinders have the same ignition point.Offset of bank 1 12.5 mmOffset of bank 2 Offset of bank 1TDC BDCOffset of bank 2 12.5 mmCentre line of cylinder Centre line of crankshaft195_110195_0777 Engine mechanicalsThe engine control unitRunning in 6 bearings, the crankshaft drives the intake camshaft by means of an intermediate shaft. The two chains are designed as single chains. Each chain has a tensioner actuated by the oil circuit.Chain tensionerIntermediate shaftChain tensioner Crankshaft195_047Engine lubricationOil coolerThe oil pump is driven by the intermediate shaft. The oil cooler and oil filter are located in the engine console. When the oil filter is changed, only the paper filter element needs to be replaced.Engine console Oil filter elementCaseIntermediate shaftA different oil filter type is used for longitudinally and transversely mountinged engines (see page 34, Service).195_048Oil pump8 Drive for auxiliariesThe longitudinally and transversely mounted V5 engines have different drives for auxiliaries.Belt routing of longitudinally mounted V5 with air-conditioning compressorDeflection pulleyMultiple-ribbed beltAlternatorVisco fanCoolant pumpAir-conditioning compressorAuxiliary steering pump195_046Deflection pulley Tension pulleyIn the longitudinally mounted engine the coolant pump is located on the auxiliary holder. As a result, this engine is slightly shorter than the transversely mounted engine.Mount for visco fan ringCoolant pump driveTension pulley195_049Auxiliary holder9 Engine designBelt routing in the transversely mounted V5 engine with air-conditioning compressorTension pulleyAlternatorCoolant pumpAir-conditioning compressorAuxiliary steering pump195_120In the transversely mounted engine the coolant pump is integrated in the cylinder crankcase.Plastic pipeCoolant pump195_12210 Power transmissionThe flywheelenables the crankshaft to rotate evenly due to its mass. It also acts as a clutch support. The clutch transmits engine torque to the gearbox. The torsional oscillations of the engine in the low speed range in particular are transferred to the gearbox in the process. This induces vibrations and consequently “gearbox rattle”.The dual-mass-flywheelprevents torsional oscillations of the engine from being transmitted to the gearbox. As the name suggests, the dual-mass flywheel consists of two flywheel masses, a primary centrifugal mass and a secondary centrifugal mass. They are interconnected by means of a spring/damping system.Engine sideGearbox side Secondary centrifugal massPrimary centrifugal massClutchClutch plateSpring/damper system195_024The dual-mass-flywheels for mounting the engines in the longitudinal and transverse positions differ from one another, since an intermediate plate is required to locate the gearbox for longitudinal mounting. Engines with dual-mass flywheels have an engine oscillation system which is tuned differently to engines with conventional flywheels. Therefore, never replace single-mass flywheels with dual-mass flywheels.11 Power transmissionEngine and gearbox with conventional flywheel-clutch layout Put simply, it can be said that a conventional fly-wheel is better at absorbing oscillations which an engine produces. But the remaining oscillations are transmitted fully to the gearbox, and this manifests itself as vibrations and noise in the low speed range.Engine Gearbox195_025Oscillations produced by the engine Oscillations absorbed by the gearbox195_027 Oscillatory behaviour of the engine and gearbox at idling speedEngine and gearbox with dual-mass flywheel The dual-mass flywheel allows slightly more engine oscillation, due to its smaller centrifugal mass. In fact, the spring/damping system and the higher gearbox moment of inertia prevent these oscillations from being transmitted to the gearbox. This results not only in a much higher level of ride comfort, but also in less wear and higher fuel efficiency at low engine speeds.Engine Gearbox195_026Oscillations produced by the engine Oscillations absorbed by the gearbox195_028Oscillatory behaviour of the engine and gearbox at idling speed12 Test your knowledge1. The V5 engine has a V-angle of a) 15°, b) 60° or c) 90°.2. Annotate the drawing. What belt pulleys drive what units?e)a) f)b)g) h)c) i) d)3. State the advantages of the dual-mass flywheel a) b) c) d) Higher ride comfort, Higher engine power, Less wear, Higher fuel efficiency at low engine speedsReasons:13 Motronic injection and ignition systemOverview of Motronic M3.8.3 systemSensorsG70 Air mass meterG28 Engine speed senderG40 Hall senderG39 Lambda probeG61 Knock sensor I G66 Knock sensor II G62 Coolant temperature sender G72 Intake manifold temperature sender J338 Throttle valve control unit with F60 Idling switch G69 Throttle valve potentiometer G88 Throttle valve positioner potentiometer Diagnosis plug conn. F F36 F63 Brake light switch Clutch switch Brake pedal switchE45 Cruise control system switch E227 Cruise control system buttonAdditional input signals e.g. road speed signal14J220 Motronic control unit Actuators G6 J17 Fuel pump with Fuel pump relayN30 N31 N32 N33 N83Injector, Injector, Injector, Injector, Injector,cylinder 1 cylinder 2 cylinder 3 cylinder 4 cylinder 5N122 Power end stage N N128 N158 N163 N164 Ignition coil Ignition coil 2 Ignition coil 3 Ignition coil 4 Ignition coil 5N79 Heater element (crankcase breather valve) N80 Solenoid valve 1 for activated charcoal filter systemN156 Twin-path intake manifold change-over valveJ338 Throttle valve control unit with V60 throttle valve positioner195_105Additional output signals, e.g. to air-conditioning compressor15 Motronic injection and ignition systemThe air mass meter with reverse flow recognitionTo guarantee optimal mixture composition and low fuel consumption, the engine management system needs to know exactly how much air the engine intakes. The air mass meter supplies this information. The opening and closing actions of the valves cause the air mass inside the intake manifold to flow in reverse. The hot-film air mass meter with reverse flow recognition detects reverse flow of the air mass and makes allowance for this in the signal it sends to the engine control unit. Thus, the air mass is metered very accurately.Intake manifoldAir mass meterReverse flow195_094DesignHousingThe electronic circuit and the sensor element of the air mass meter are accommodated in a compact plastic housing. Located at the lower end of the housing is a meter-ing duct into which the sensor element projects. The metering duct extracts a partial flow from the air stream inside the intake manifold and guides this partial flow past the sensor element. The sensor element measures the intake and reverse air mass flows in the partial air flow. The resulting signal for the air mass measurement is processed in the electronic circuit and sent to the engine control unit.Housing coverMetering duct Electric circuit Sensor elementPartial air flow195_09216 Functional principleMounted on the sensor element are two temperature sensors (T1 + T2) and a heating element.Air mass meter with sensor element inside the metering ductThe substrate to which the sensors and heating element are attached is composed of a glass membrane. Glass is used because of its poor thermal conductivity. This prevents heat which the heating element radiates from reaching the sensors through the glass membrane. This can result in measurement errors.Design of sensor element (schematic diagram)Air flowT1Heating elementT2195_041The heating element warms up the air above the glass membrane. The two sensors register the same air temperature, since the heat radiates uniformly without air flow and the sensors are equidistant from the heating element.T1 T2195_042Induced air mass recognition In the intake cycle, an air stream is ducted from T1 to T2 via the sensor element. The air cools sensor T1 down and warms up when it passes over the heating element, with the result that sensor T2 does not cool down to as great an extent as T1. The temperature of T1 is therefore lower than that of T2. This temperature difference sends a signal to the electronic circuit that air induction has occurred.T1T2195_04317 Motronic injection and ignition systemReverse air mass flow recognition If the air flows over the sensor element in the opposite direction, T2 will be cooled down to a greater extent than T1. From this the electric circuit recognises reverse flow of the air mass. It subtracts the reverse air mass flow from the intake air mass and signals the result to the engine control unit. The engine control unit therefore obtains an electrical signal: it indicates the actual induced air mass and is able to meter the injected fuel quantity more accurately.T1T2195_044Signal utilisation The signal which the air mass meter sends is used to calculate all speed- and load-dependent functions, e.g. injection time, ignition timing or tank venting.Electric circuit The air mass meter is connected to the engine control unit via two signal lines and one earth line and is supplied with power via connection 87a in the engine wiring harness.Effects of signal failurePower supplyIn the event of failure of the air mass meter, the engine management system computes a substitute value. This emergency function is so well adapted that the fitter cannot tell from the running behaviour of the engine whether the air mass meter is defective. This can only be done by reading out the fault memory. This means that the defect will be detected at the latest during the exhaust emission test which takes place every two years if not during the routine service checks.G70J220195_11118 The twin-path intake manifoldTwin-path intake manifolds are a new development. Their task is to develop high low-end torque by means of the long port in the intake manifold and deliver high top-end power by means of the short port in the intake manifold. In contrast to previous systems, change-over of the intake manifold paths in the V5 engine is performed by a rotary valve instead of change-over valves.195_131Change-over valveAir flow when using change-over valve The change-over valves are housed in the intake port. As a result, they change the flow cross-section and the flow behaviour of the intake air inside the port. Turbulence occurs even if the valves are fully open.195_022Turbulence during valve controlRotary valveAdvantage of using a rotary valve The advantage of using a rotary valve instead of a valve actuator is it ensures optimal flow behaviour of the air drawn into the intake manifold. The shape of the rotary valve replicates the cross-section of the intake duct. Air-flow behaviour is not impaired when the rotary valve is open. As opposed to the valve actuator, turbulence does not occur.195_108Closed rotary valve195_023 An optimal flow characteristic is achieved when the rotary valve is open19 Motronic injection and ignition systemOn closer examination it can be seen that the processes taking place inside the twin-path intake manifold are more complex than at first meet the eye. We will therefore devote this section to explaining the functional principle of the intake manifold, beginning with its design.Intake manifold upper section with torque and performance portsDesign The intake manifold comprises an intake manifold upper section together with the torque ports, performance ports and rotary valves, and the intake manifold lower section. In longitudinally and transversely mounted engines the intake manifold is made of aluminium or plastic respectively. Plastic is the preferred material for transversely mounted engines. This is because the intake manifold shatters when it collides with the engine compartment bulkhead in a crash and prevents the engine from intruding into the passenger compartment.Intake manifold lower sectionRotary valve195_089The intake manifold of the V5 engine is based on the ram pipe charge principle. Was does this mean? The key components of the twin-path intake manifold are the torque ports and the performance ports. As their name already suggests, the ports are designed to collect something. Indeed, they collect air and produce what is known as the “self-charging effect“. This effect arises from the propagation of pressure waves or oscillations inside the intake manifold. The name “ram pipe charging” is derived from this.195_021Torque port Output manifold195_020Intake valveCombustion chamber Rotary valve20 Actuation Change-over is speed- and load-dependent. The engine control unit activates the solenoid valve for changing over the ports in the intake manifold. This valve admits a partial pressure into the vacuum box. The vacuum box in turn actuates the rotary valve and ensures smooth changeovers even at high revs. The non-return valve prevents the vacuum box from being vented if pressure fluctuations occur inside the intake manifold.Position of the twin-path intake manifold Change-over takes place: up to approx. 900 rpm Idling/performance position = short intake manifold as of approx. 900 rpm Torque position = long intake manifold above approx. 4300 rpm Performance position = short intake manifoldRotary valveIntake manifoldto performance portfrom torque portto intake valve Vacuum boxSignal from engine control unitPort change-over valve N156 Nonreturn valveVacuum box195_106to fuel pressure regulator21 Motronic injection and ignition systemFunctional principleTorque port Output manifoldAfter combustion has taken place, there is a pressure differential between the cylinder and intake manifold. When the intake valve opens, an intake wave forms inside the intake manifold and propagates from the inlet port towards the torque port at the speed of sound.Intake valve Rotary valve195_011The open end of the pipe in the torque port has the same effect on the intake wave as a solid wall has on a ball. The wave is reflected and propagates back to the inlet port in the form of a pressure wave.Reflection point of torque port195_012At an optimal intake manifold length, the max. pressure reaches the inlet port shortly before it closes. The pressure wave enables more air to be admitted into the cylinder, and improves the amount of fuel-air mixture in the cylinder. This is what’s called the self-charging effect.Inlet port is still open.195_013As engine speed increases, the pressure wave has less time to reach the inlet port. Because the pressure wave is only able to propagate at the speed of sound, it reaches the inlet port too late. It is already closed. Self-charging does not take place. This problem can be solved by shortening the intake manifold.Inlet port is already closed195_01422 In the V5 engine, the rotary valve turns to the performance position at an engine speed of 4300 rpm. This opens up the path to the performance port. The performance port is designed so that the intake and pressure waves follow a shorter path to the inlet port. The performance port is filled with air when the inlet ports are closed.Performance port is filled.Rotary valve195_015When the inlet port opens, an intake wave propagates uniformly inside the intake manifold.195_016The intake wave reaches the pipe end in the performance port before it does in the torque port. There it is reflected and returns to the inlet port.Reflection point of performance portReflection point of torque port195_017Unlike the pressure wave which propagates back from the torque port, the intake wave arrives before the inlet port closes. It therefore has a self-charging effect.195_019The wave arriving too late from the torque port is reflected by the closed injectors and fills the performance port.23 Motronic injection and ignition systemCruise controlCruise control enables the driver to set a constant road speed of 45 kph and above. Once activated, cruise control maintains the set speed regardless of topography without the driver having to press the accelerator pedal. In the previous system the throttle valve was opened electro-pneumatically depending on the set road speed.The signal which the cruise control switch generates is transmitted to the engine control unit, which in turn activates the throttle valve control unit. A control unit for cruise control is no longer needed. The throttle valve positioner opens the throttle valve depending on the road speed setting.Cruise control switch On and Off signalsSignals to the engine control unit Engine speed signal Air mass signal Road speed Brake operated Clutch operatedEngine control unitFeedback signal of throttle valve positionServo motor actuationThrottle valve control unit195_093Cruise control only operates at a road speed of 45 kph or above.24 The throttle valve control unitVolkswagen has been fitting the throttle valve control unit to its engines since early 1995. After it is activated by the engine control unit, the throttle valve control unit regulates idling speed. You will find further information on this in SSP 173.G88The component parts are: l l l l Idling switch F60, Throttle valve potentiometer G69, Throttle valve positioner potentiometer G88, Throttle valve positioner V60.F60 G69V60195_054The throttle valve control unit also actuates the throttle valve while the cruise control is switched on. Apart from minor differences, the new throttle valve control unit has the same design as the old one. The main difference is that the gearwheel segment is larger. This enables the servo motor to operate the throttle valve across the full adjustment range.Gearwheel segment without cruise controlGearwheel segment with cruise control195_055195_05625 Motronic injection and ignition system195_057Idling switch F60Signal utilisation When the idling switch is closed, the engine management system knows that the engine is idling.195_061Electric circuitJ220Effects of signal failure In the event of signal failure, the values of the engine management potentiometer are used to detect when the engine is idling.G40195_073J338Sensor earthThe idling switch utilises the sensor earth of the engine control unit.195_060Throttle valve positioner V60The throttle valve positioner is an electric motor and has the capability to actuate the throttle valve over the full throttle valve operating range. Electric circuit Effects of failureJ220195_064To control idling, the emergency running spring draws the throttle valve into the emergency running position. The cruise control fails.G40195_070J338V60 is activated by the engine control unit.26 195_058Throttle valve potentiometer G69Signal utilisation This potentiometer enables the engine control unit to recognise the position of the throttle valve.195_062Electric circuit Effect of signal failure If the engine control unit does not receive a signal from this potentiometer, it will compute a substitute value based on engine speed and the signal which the air mass meter sends.G40 J220J338195_072Sensor earthG69 utilises the sensor earth of the engine control unit. The voltage supply is identical to that of G88.195_059Throttle valve positioner potentiometer G88Signal utilisation This potentiometer signals the position of the throttle valve drive to the engine control unit.195_063Electric circuitJ220Effect of signal failureG40If this signal is not received, the idling control goes into an emergency mode. A higher idling speed indicates this. The cruise control fails.J338195_071Sensor earth27 Motronic injection and ignition systemThe quick-start sender wheelis secured to the camshaft. The signal it sends enables the engine control unit to recognise more quickly the position of the camshaft in relation to the crankshaft and, in conjunction with the signal which the engine speed sender generates, to start the engine more quickly. In previous systems the first combustion cycle was initiated after a crank angle of approx. 600-900°. The quick-start sender wheel enables the engine control unit to recognise the position of the crank-shaft in relation to the camshaft after a crank angle of only 400-480°. As a result, the first combustion cycle can be initiated sooner and the engine starts more quickly.Track 1The quick-start sender wheel consists of a twin-track sender wheel and a Hall sensor. The sender wheel is designed with two tracks located side by side. Where one track has a gap, the other track has a tooth.Twin-track sender wheel Track 2The Hall sensor comprises two Hall elements located side by side. Each Hall element scans a single track. This device is known as a differential Hall sensor because the engine management system compares the signals of the two elements.ToothGapHall element track 1 Hall element track 2195_031Hall sensor28 Function The sender wheel is designed so that the two Hall elements never generate the same signal. When Hall element 1 is facing a gap, Hall element 2 is always facing a tooth. Hall element 1 therefore always generates a different signal to Hall element 2. The control unit compares the two signals and is thus is able to recognise the cylinder at which the camshaft is located. Using the signal which the engine speed sender G28 generates, the injection cycle can be initiated after a crank angle of approx. 440°.Track 1 Track 2 Hall element track 2 recognises tooth Signal2 =1Hall element track 1 recognises gap Signal1 =0195_032Track 1 Track 2 Hall element track 2 recognises gap Signal2 =0Hall element track 1 recognises tooth Signal1 =1195_033Electric circuit The Hall sender G40 is connected to sensor earth of the engine control unit. If the Hall sender fails, the engine cannot be restarted.J220J338G40195_06929 Motronic injection and ignition systemThe ignition systemThe V5 engine is equipped with a static high voltage distributor. Due to the uneven number of cylinders, the V5 utilises a power end stage with a single ignition coil for each cylinder. The ignition coils are grouped together in a single module.Motronic engine control unit Power end stage N122Ignition coils N, N128, N158, N163, N164195_036Advantages: l No wear l High reliability30 Power end stage N122 Each of the five ignition output stages “pumps” a high amperage into the ignition coils to ensure that there is enough power to produce the ignition spark.195_090Ignition coils N, N128, N158, N163, N164 Due to the uneven number of cylinders, it was not possible to use twin ignition coils for the ignition system as in the case of the VR6 engine.195_097Electric circuit The power end stage, together with the ignition coils and the engine control unit, are supplied with power via the fuel pump relay J17. Each cylinder has its own ignition output stage and therefore also has an output wire from the engine control unit.N S N128 N158 N163 N164N122J220195_11631 Function diagram30 15 X 31 J1730 15 X 31N S S S S SN128 N158 N163 N164G6G39N80G70N83N33 N32 N31N30N122J220G88 V60 G69F60G62G72G40J338G28G66G61Components F60 G6 G28 G39 G40 G61 G62 G66 G69 G70 G72 G88 Idling switch Fuel pump Engine speed sender Lambda probe Hall sender Knock sensor I Coolant temperature sender Knock sensor II Throttle valve potentiometer Air mass meter Intake manifold temperature sender Throttle valve positioner potentiometer Fuel pump relay Motronic control unit Throttle valve control unit N30 N31 N32 N33 N80 N83 N N122 N128 N158 N163 N164 V60 Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4 Solenoid valve 1 for activated charcoal filter system Injector, cylinder 5 Ignition coil 1 Power end stage Ignition coil 2 Ignition coil 3 Ignition coil 4 Ignition coil 5 Throttle valve positioner195_103J17J220 J33832 30 15 X 3130 15 X 31SSSN79N156F36F47FE45E227J220ABCDEFGHIJKComponents E45 E227 F F36 F47 G70 J220 N79 N156 Cruise control system switch Cruise control system button (set) Brake light switch Clutch switch Brake pedal switch for cruise control Air mass meter Motronic control unit Heater element (crankcase breather) Intake manifold change-over valve A B C D E F G H I J K195_104Road speed signal Fuel consumption indicator signal Engine speed signal Air conditioning on standby Throttle valve position signal Diagnostics/immobiliser data wire Air-conditioning compressor Automatic gearbox signal ABS/EDL data line ABS/EDL data line Automatic gearbox signal33 ServiceLongitudinal and transverse mountingPlease note that the add-on parts of the V5 engine for longitudinal and transverse mounting are very different. The parts highlighted in blue indicate where the V5 engine intended for longitudinal mounting shown below differs from the engine intended for transverse mounting.Heat shieldVisco fanPosition of secondary air valveDipstickAlternatorCombined holder Exhaust manifold Coolant pumpEngine consoleAir-conditioning compressorOil filter195_045Oil sumpAuxiliary steering pump34 Special toolsFor the V5 engine, additional holes must be drilled in special tools Engine Holder 3269 and Counter-holder 3406.For Engine Holder 3269, mark three drill-holes from the centre outwards. Please note that holes may only be drilled for the engine which has code AGZ, i.e. the longitudinally mounted engine.195_099For Counter-holder 3406, position the drill-holes in parallel with the existing drill-hole.Then seal the surface of the special tool with corrosion inhibitor.195_10035 Self-diagnosisYou can select the following functions in the selfdiagnosis: 01 Interrogate control unit version 02Interrogate fault memory 03 Actuator diagnosis 04 Basic adjustment 05 Erase fault memory 06 End of output 07 Encode control unit 08 Read measured value block 10 AdaptationBasic adjustment must be performed after completing the following work: - Engine control unit, - Throttle valve control unit, - replace engine or - disconnect battery terminalsFunction 02 Interrogate fault memory The self-diagnosis stores faults in the components highlighted below in the fault memory. These faults can be read using fault reader V.A.G. 1551 or V.A.G. 1552.G70 G28 G40 G39 G61 G66 G62 G72 J338 with F60 G69 G88 F F36 F63 E45 E227 J220J17 N30, N31, N32, N33, N83N80 N156J338 with V60195_11736 Test your knowledge1. What is the special feature of the new hot-film air mass meter?2. Annotate the following drawing.a) f) b) g) c) h)d) i)e)j)k)3. Why does the engine start more quickly with a quick-start sender wheel?4. What is a performance port and what purpose does it serve?37 Notes38 39 Solutions: Page 13 1. a) 2. a) Deflection pulley, b) Air-conditioning compressor, c) Deflection pulley, d) Crankshaft, e) Alternator, f) Visco van, g) Coolant lpump, h) Tension pulley, i) Auxiliary steering pump 3. a), c), d) 4. Fewer oscillations are transmitted from the engine to the gearbox. Page 37 1. The air mass meter has reverse flow recognition. 2. a) Rotary valve, b) to output manifold, c) Vacuum box, d) Signal from engine control unit, e) Vacuum box, f) Intake manifold , g) from torque port, h) to intake valve, i) Register intake manifold change-over valve, j) Nonreturn valve, k) to fuel-pressure regulator 3. Thanks to the configuration of the gear teeth and gaps on the two-track sender wheel and the Hall sensor with two Hall elements, the engine control unit receives a signal which enables it to determine the position of the camshaft in relation to the crankshaft more quickly. 4. The performance port is a component part of the twin-path intake manifold. It serves to improve volumetric efficiency in the upper speed range and thus to increase power output. Service.195For internal use only © VOLKSWAGEN AG, Wolfsburg All rights reserved. Subject to change. 740.2810.13.20 Technical status: 12/97` This paper was made from chlorinefree bleached cellulose.