TECHNICAL DOCUMENTATION

SSP 203 The 1.0-ltr 37 kW petrol engine

PDFEN24 pages1 MB
SSP 203 The 1.0-ltr 37 kW petrol engine - PDF cover

This PDF is currently unavailable.

Read document text
The 1.0-ltr. 37 kW petrol engine with camshaft in block (ohv)Design and function363224 P (kW)161284 1000 2000 n (1/min) 3000SELF-STUDYPR20OGRAM28ME N o . 203 In the Lupo, VW will be extending its range of petrol engines with a new 1.0-ltr. engine with aluminium block with camshaft in block (ohv). It conforms to the exhaust emission standards EU III and D3. This compact and light-weight engine is an in-Group development and is based on proven engine components.203/24In this Self-Study Programme, we will explain to you the design and function of this new engine. At a glanceSpecifications .............................................................. 4Engine data Engine overviewEngine mechanicals ................................................... 6Crankshaft Cylinder block Cylinder liner Timing gears Valve timing adjustment Oil pump Valve timing Drives for auxiliary components Coolant pumpSystem overview ........................................................ 10Engine management system Simos 2P Sensors/actuatorsSensors ......................................................................... 14Engine speed sender G28 and TDC recognition Intake manifold pressure sender G71 and intake air temperature sender G41 Knock sensor G61Injection system .......................................................... 17Intake module with injectorsFunctional diagram .................................................... 18Self-diagnosis ............................................................. 20Test your knowledge .................................................. 21New Important NoteThe Self-Study Programme is not a Workshop Manual.Please always refer to the relevant Service Literature for all inspection, adjustment and repair instructions.3 SpecificationsEngine dataEngine code: Type: Displacement: Bore: Stroke: Compression ratio: Rated output: Max. torque: Mixture preparation: Fuel: AHT 4-cylinder in-line engine 997 cm3 72 mm 61.2 mm 10 : 1 37 kW at 5000 rpm 84 Nm at 3250 rpm Simos 2P multipoint injection system 95 RON unleaded. The vehicle can alternatively be operated on 91 RON fuel via the knock control with a slight reduction in torque and performance.40 36 32 28 24 20 16 12 8 4 1000 2000 3000 n (1/min) 4000 5000 6000 90 80 M (Nm) 70 60 50P (kW)203/1203/234 Engine overviewThe engine has a crossflow cylinder head with 2 valves per cylinder. A twin roller chain drives the in-block camshaft (ohv). Hydraulic tappets, push rods and rocker levers make for a play-free valve gear.Carrier for engine mount, combined with coolant pumpPush rodTwin roller chain Tappets with hydrauli valve liftersCamshaftOil pumpFlywheel with segments for engine speed and TDC recognition Cylinder block made of die cast aluminium203/215 Engine mechanicalsCrankshaft– – Mounted in 3 bearings The main bearing (in the centre) is located in between the crankshaft journals of the 2nd and 3rd cylinders. The crankshaft is fixed in an axial direction by the centre main bearing.Centre main bearing–203/12Cylinder linerCylinder block– made of die cast aluminium– The cylinder liners are not an integral part of the cylinder block.Cylinder block203/13Cylinder liners– The four cylinder liners are made of grey cast iron and installed individually in the cylinder block. They are interchangeable. The cylinder liners are directly swept with coolant (wet type bushes). The lower section of the cylinder liners are sealed off from the cylinder block with copper sealing discs. Cylinder liner pretensioning is also adjusted with these sealing discs. Pretensioning is measured during installation. 3 different thicknesses of copper sealing disc are available for adjusting the pretensioning.Cylinderhead gasket Cylinder head Cylinder liner––Coolant– The pretensioned cylinder liner is sealed off from the cylinder head by means of the cylinder head gasket.Copper sealing disc Cylinder block203/116 Timing gears– The in-block camshaft (ohv) is driven by the crankshaft by means of a twin roller chain. The whole drive is covered by the timing gear cover.–203/14Valve timing adjustmentThe position of the sprockets on the shafts is set by means of a fitting key. For adjusting the port timing, there is a mark on the crankshaft sprocket and on the camshaft sprocket. The two sprockets are engaged in the chain so that the marks are separated by 12 chain pins.Crankshaft sprocketTwin roller chainCamshaft sprocketFor detailed instructions on adjustment, please refer to the Workshop Manual.203/15Worm gear for oil pump drive12CamshaftOil pumpThe oil pump drive and the oil pump are located below the timing gear cover. The oil pump is a gear type pump. The oil pump is driven via the camshaft. The oil pump gear is driven via worm gears and a vertical shaft. The second oil pump gear is driven by the oil pump gear and revolves around a fixed journal.Timing gear coverOil pump gears203/337 Engine mechanicalsValve timingThe valves are activated by the in-block camshaft (ohv) via a push rod and rocker lever. Valve clearance is adjusted by the hydraulic system in the tappet dependent on the engine oil pressure. Valve clearance stays constant throughout the engine running time. After carrying out repairs, re-adjust the valve clearance to basic position using the rocker lever adjusting screw.Tappet with hydraulic valve lifters Rocker lever Rocker lever adjusting screw Push rod203/3.3CamshaftThe tappet and the hydraulic valve lifters function in the same way as conventional bucket tappets. (For a description of the bucket tappet, please refer to SSP 105).Tappet Tappet pistonPush rodOil inlet High-pres. chamber Oil supply Camshaft Non-return valveWhen performing repair work, set down the tappets in their installed position to keep them filled with oil. Absolute cleanliness is essential when carrying out all repairs.203/28 Drives for auxiliary unitsAll auxiliary components are driven by the crankshaft via a ribbed V-belt . In the basic version, these are: – – the coolant pump the alternatorAlternatorThe tension of the ribbed V-belt is adjusted via the swivelable alternator.Coolant pumpIf the engine has a servo pump or an air conditioner compressor, the ribbed V-belt is tensioned by an additional tension pulley.CrankshaftDeflection pulley203/9Support for engine mountCoolant pumpBearing housingThe coolant pump is located at the end face of the cylinder block . The coolant pump bearing housing also serves as a support for the engine mount.Coolant pump drive gearCylinder blockCoolant Coolant pump rotor203/10Coolant tube connection 9 System overviewSimos 2P engine management systemThe Simos engine management regulates fuel injection and ignition depending on the current engine load. The engine load is determined by the engine speed sender and the intake manifold pressure sender. From this, the control unit calculates the ignition point and injection period making allowance for any correction factors. Correction factors are: – Cylinder-selective knock control – Lambda control – Idling control – Activated charcoal filter controlN152P/Q N30G39 Z19 G62 G61G28Legend G6 G39 G28 G42 G61 G62 G71 J 17 J361 J338 N30 N80 N152 P Q Z19 Fuel pump Lambda probe Engine speed sender Intake air temperature sender Knock sensor Coolant temperature sender Intake manifold pressure sender Fuel pump relay Simos 2P control unit Throttle valve control unit Injector Solenoid valve for act. charcoal filter Ignition transformer Spark plug socket Spark plugs Lambda probe heaterFor a description of the throttle valve control unit, please refer to SSP 173.10 C BJ338AN80 D G71 G42 J17J361SIMOS 2PEG6203/6= Output signal = Input signalA B C D E= = = = =Fuel filter Fuel pressure regulator Distributor Act. charcoal filter Diagnosis plug= Fuel supply line = Fuel return line = Intake air = Exhaust gas 11 System overviewSensorsEngine speed sender G28Intake manifold pressure sender G71 and intake air temperature sender G42Idling speed switch F60 Throttle valve positioner potentiometer G88 Throttle valve potentiometer G69Coolant temperature sender G62Lambda probe G39Knock sensor G61Pressure switch for power steering F88Air conditioner compressor (air conditioner switch activation) Air conditioner compressor (in) Air conditioning system (pressure sensor) Road speed signal Terminal 50 (starter, ignition switch)12 ActuatorsSimos 2P control unit J361 Fuel pump relay J17Injectors N30 ... N33Ignition transformer (4x) N152 (injector rail)Throttle valve control unit J338 Throttle valve positioner V60Lambda probe heater Z19Diagnosis plug connectionSolenoid valve for activated charcoal filter N80Road speed signal (instrument cluster) Air conditioner compressor (out)203/2813 SensorsEngine speed sender G28 and TDC recognition senderSegment gap edgesThe sender is a sensor which operates in accordance with the Hall principle. The Hall sender is activated via the segment gaps on the flywheel. A segment gap is continuous and a segment gap has an additional tooth. The edges of the segment gaps generate two pulses at an interval of 48o crank angle for every cylinder to be fired. The control unit recognises these differences from the signal characteristic and assigns the appropriate cylinders.CrankshaftContinuous segment gap203/7Engine speed sender Flywheel with segment gapsThe engine load control unit utilises the signals to calculate the ignition advance angle and injection point.Continuous segment gapTDCThis difference is important when mounting the flywheel on the crankshaft. The segment gap with tooth must be facing the oil sump at TDC cylinder 1.The TDC mark on the crankcase is then 24.5o after the edge of the continuous segment gap.203/8Segment gap with toothIn the event of signal failure, the engine will remain at a standstil.continuous with tooth= cylinders 1 and 4 = cylinders 2 and 314 Intake manifold pressure sender G71 and intake air temperature sender G42The sender is directly mounted on the intake manifold. The pressure sensor and air temperature sensor are in direct contact with the intake air in the intake manifold.Intake manifold Intake airSignal utilisation Intake manifold pressure and intake air temperature are transferred to the engine control unit. They are required for calculating the engine intake air quantity. The necessary injection time as well as the ignition point are calculated using this data.203/29Substitute function If signals are missing, the engine control unit utilises the signal supplied by the throttle valve potentiometer and engine speed to calculate the injection time and ignition point. An emergency running map is taken as the basis. If the signal of the intake air temperature sensor is missing, a substitute value of 45oC is utilised.Intake manifold pressure sender and intake air temperature senderElectrical circuitJ361Self-diagnosis The self-diagnosis monitors the two input signals. The following faults can be detected: – – – Short circuit to ground Short-circuit to positive voltage and reference voltage Open circuitG71G42203/30G42 G71 J361Intake air temperature sender Intake manifold pressure sender Control unit for Simos15 SensorsKnock sensor G61The knock sensor is attached to the rear wall of the crankcase between cylinders 2 and 3. Signal output The engine control unit recognises knocking combustion from voltage signals sent by the knock sensor. This is recorded separately for each cylinder = cylinder-selective knock control Signal utilisation The ignition advance angle of the cylinder in question is shifted towards "retard" in steps of 0.5 to 2o until the tendency to knock diminishes. The maximum possible ignition angle adjustment is 15o. The ignition point can thus be adjusted individually to the knock limit for every cylinder. If no further knocking occurs, the ignition advance angle returns to the mapped value in steps of 0.5o crank angle. Substitute functionScreening Electrical circuit203/31Knock sensor G61J361If a signal is missing, the ignition advance angle of all 4 cylinders is reduced by 15o. This leads to a reduction in engine performance. Self-diagnosis The self-diagnosis is activated at a coolant temperature of 20oC, an engine speed of over 3350 rpm and an engine load of over 60 %. The fault “Sensor signal too weak“ is detected. G61 J361G61203/32Knock sensor Control unit for SimosThe tightening torque of the fastening bolt has a bearing on the function of the knock sensor. It is essential to adhere to the prescribed tightening torque of 20 Nm.16 Injection systemIntake module The intake module carries the fuel rail together with the injectors, the pressure regulator, the intake air sender and intake manifold pressure senderIntake manifold pressure sender and intake air temperature sender Connection for throttle valve control unit Fuel railInjection Each cylinder has an injector which is located upstream of the intake valve in the intake manifold.The injected fuel is collected in the intake port and drawn into the combustion chamber with the air when the intake valve opens.Injectors203/4Activation The injectors are supplied with power via the fuel pump relay and activated by the control unit via GND. The injectors are activated in pairs (semi-sequential injection) (cylinders 1 and 4 as well as cylinders 2 and 3). The control unit makes allowance for the following correction factors when determining the opening time of the injectors: – – – – Cylinder-selective knock control Lambda control Idling control Activated charcoal filter control.M30 15J17 4SSG6N30N31N32N3331J361203/1617 Functional diagramFunctional diagram of Simos 2PComponents A Battery F60 Idling speed switch F88 Power steering pressure switch G6 Fuel pump G28 Engine speed sender G39 Lambda probe G42 Intake air temperature sender G61 Knock sensor G62 Coolant temperature sender G69 Throttle valve potentiometer G71 Intake manifold pressure sender G88 Throttle valve positioner pot. J17 Fuel pump relay J361 Control unit for Simos J338 Throttle valve control unit N152 Ignition transformer (4x) N30...33 Injectors N80 Solenoid valve for activated charcoal filter P Spark plug socket Q Spark plugs S Fuse V60 Throttle valve positioner Z19 Lambda probe heater30 15J17 4SSSZ19G3λN30 + N31 N32 N33AM V60 G88 +Auxiliary signals A Engine speed B Air conditioner compressor (in - out) C A/C ready (in) Air conditioner switch activation D Air conditioner PWM (in) Check signal, e.g. for “Air conditioner load“ E K-wire (for diagnosis) F Road speed signal G Terminal 50F60 J338G69 G28-MG631Code codes/Legend= Input signal = Output signal18 30 15SSSSN80ABCDEFG4914 J361941N152G71G42G61F88G62IIVIIIIIQ P31203/5= Batt. positive terminalin out= GND19 Self-diagnosisC B N152P/Q N30J338AN80 G39 Z19 G62 G71 G61 G42 J17 DJ361SIMOS 2P G28EG6203/25The self-diagnosis monitors the sensors, the actuators and the control unit. If the control unit identifies a fault, it calculates substitute values from the other input signals and provides emergency running functions. The fault is saved to the fault memory. In addition, measured values are displayed in the read measured value block function for troubleshooting purposes. All colour-coded system components are contained in the self-diagnosis. Self-diagnosis can be performed with fault readers V.A.G 1551, V.A.G 1552 and VAS 5051.V.A.G - EIGENDIAGNOSE 01 - MotorelektronikHELP1 2 3 4 5 6 7 8 9 C 0 QHELPPRINT203/26The following functions are possible: 01 02 03 04 05 06 08 Interrogate control unit version Interrogate fault memory Actuator diagnosis Interrogate basic adjustment Erase fault memory End of output Read measured value blockFor detailed information on the selfdiagnosis procedure, please refer to the Workshop Manual 1.0-ltr./37 kW Engine Simos Injection and Ignition System.20 Test your knowledgeSolutions203/22211. C; 2. B; 3. a chain, count the chain pins; 4. flywheel, engine speed sender, an additional tooth, 1 and 4, 2 ad 3; 5. A, C; 6. C; 7. A, B, C; 8. B; 9. A, C Test your knowledgeWhat answers are correct? Sometimes only 1 answer is correct. However, more than one answer may be correct – or maybe all the answers are correct! Please fill in the spaces ...............................1.Valves are controlled A. B. C.directly by the horizontal camshaft, via rocker lever, via push rods and rocker lever.2.Basic adjustment of valve clearance is performed during assembly. A. B. C.The valve clearance must be adjusted every 15,000 km or during the annual inspection. As hydraulic valve tappets are used, there is no need for mechanical adjustment during inspections. The basic adjustment must be repeated after a mileage of 1,000 km.3.The camshaft is driven by .............................. .............................. .Valve timing is adjusted by means of .............................. from mark to mark.4.Segments for recognition of ............................... are attached to the .............................. . A segment carries .............................. .This makes it possible for the control unit to distinguish whether the signal belongs to cylinders ..... and ..... or ..... and ..... .?203/2222 5.The intake module carries the fuel rail together with the injectors. A. B. C. Each cylinder has an injector. Fuel is injected directly into the combustion chamber. Fuel is injected into the intake manifold upstream of the intake valve.6.The injection system operates semi-sequentially. Semi-sequentially means: A. B. C.Fuel is injected in two steps. Fuel is injected sequentially, not simultaneously. Two injectors inject fuel simultaneously (groups 1 and 4 as well as 2 and 3).7.The engine has wet type cylinder liners. This means that A. B. C.The coolant sweeps the cylinder liners directly, The cylinder liners are not an integral part of the cylinder block, Cylinder liners can be replaced when repair work is necessary.8.The oil pump is driven A. B. C.by the crankshaft by means of a chain, by the camshaft by means of a shaft, by the camshaft by means of a chain.9.The coolant pump is located on the face end of the engine. A. B. C.It is driven by means of the common ribbed V-belt for driving all the auxiliary components. It is driven by means of a separate V-belt. Its bearing housing also serves as the support for the engine mount.?23 Service.203For internal use only. © VOLKSWAGEN AG, Wolfsburg All rights reserved. Technical specifications subject to change without notice. 840.2810.22.20 Technical status: 05/98❀ This paper is produced from non-chlorine-bleached pulp.