TECHNICAL DOCUMENTATION

SSP 207 The Audi TT Coupé

PDFEN92 pages4 MB
SSP 207 The Audi TT Coupé - PDF cover

This PDF is currently unavailable.

Read document text
Service.The Audi TT CoupéDesign and FunctionSelf-Study Programme 207For internal use only. The plant – the plantsIngolstadt plant The model series Audi A4 and Audi A3 are produced in Ingolstadt. A separate production line has been set up for the body in white of the Audi TT Coupé. The head office of Technical Development is also located in Ingolstadt.Special trucks were developed for transferring the bodyshells to Györ for final assembly.High-tech from Györ Qualified specialists and a good infrastructure are key factors for the Audi production shop in Györ. Audi has been manufacturing four-cylinder 5V, V6 and V8 engines here since 1997. Final assembly of the TT has also been taking place here since 1998.Axle and steering geometry measurement100% reliability is ensured through a series of systematic checks integrated in the production process.Watertightness testFunctional tests are an integral part of the production process Mounted parts are tested for accuracy of fit, build quality and functionality after each stage of assembly.Quality that is measurable After final assembly, extensive tests and adjustments are carried out on every single Audi.Electrical function test Roller dynamometerExhaust emission test and optimal setup Acoustic test bench 2 ContentsPage A brief introduction to the TT . . . . . . . . . . . . . . . . . . . . 4Design needs no explanation Vehicle dimensions Vehicle identification Environmentally-friendly productionBody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Special featuresVehicle safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Occupant protection Fuel cut-offDrive units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Engine and gearbox combinations 1.8-ltr. 132 kW 5V turbocharged engine AJQ 1.8-ltr. 165 kW 5V turbocharged engine APXSubsystems of the Motronic . . . . . . . . . . . . . . . . . . . 37Lambda control in the EUIII Torque-oriented engine management Accelerator position sender Electrically-activated throttle valveFuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Power transmission . . . . . . . . . . . . . . . . . . . . . . . . . . 485-speed manual gearbox 6-speed manual gearbox Haldex viscous couplingRunning gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Steering Front axle Rear axle Brake systemElectrics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Vehicle electrical system Interior monitoring Immobiliser Sound systemHeating/air conditioning system . . . . . . . . . . . . . . . . 76Overview Expansion valveService . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Flexible service interval indicator Oil level sensor Specifications Special toolsNew. The Self-Study Programme provides you with information regarding design and function. The Self-Study Programme is not a Workshop Manual. Please refer to the Service Literature for all the relevant maintenance and repair instructions.Important. Note.3 A brief introduction to the TTDesign needs no explanationThe name alone suggests that this is an Audi with a difference. The Audi TT was named after the legendary Tourist Trophy race on the Isle of Man - the only one of its kind in the world. The Audi TT is equally as unique as its legendary namesake. The interior styling matches the exterior perfectly - a fact reflected in the features of the dash panel, the styling of the instruments, the air nozzles and controls. The styling of some parts has also been influenced by the use of aluminium.Engines As befits a sports car, the Audi TT is powered by a four-cylinder 5-valve turbocharged engine developing 180 bhp with a sports gearbox in the front-wheel drive and quattro versions. A four-cylinder 5-valve turbocharged engine developing 225 bhp is available for the quattro version.Running gear The running gear also underscores Audi’s total commitment to the sports car concept. The front axle kinematics were revised with regard to steering quality and response. This, in combination with the Audi TT’s sporty, stiff suspension tuning, ensures excellent handling and a high standard of driving safety.The basic version is equipped with 16-inch wheels shod with size 205/55 R 16 tyres. A 17-inch suspension is standard with the quattro and available as optional equipment for all other engine variants.4 There is no doubt that the real highlight of the Audi TT is its emotive design, both on the exterior and in the interior. The engineers at Audi had an ambitious development goal: to meet all functional and quality standards as well as the latest statutory requirements and Audi’s high standards of safety without compromising the design concept and while retaining the car’s full viability for everyday use.Quattro power train The TT will feature a new generation of Audi technology and the new Haldex viscous coupling, further emphasising the vehicle’s sporty character.SSP207/1Safety Safety is paramount: That’s why the TT is equipped with front airbags for the driver and front passenger. The TT already complies with the new European safety laws which will come into effect in the year 2003 as well as the tougher requirements according to the US Head Impact Protection Act.Design We at Audi firmly believe that the most important thing about designing is that actions speak louder than words. Suffice to say, a good design speaks for itself. The TT has a “wheel-hugging” design, that is to say the entire body is styled around the wheels. That also goes for the front and rear bulges as well as the roof and window lines and the low-slung passenger cabin.5 A brief introduction to the TTVehicle dimensions13541525 17641507 (quattro 1503) 1856The “+ and –“ dimensions are reference values compared to the Audi A3 Length: Width: Height: –111 mm +45 mm –69 mmTrack width Front: Rear:+12 mm +12 mm + 8 mm quattro Wheelbase: –93 mm –85 mm quattro9598288762419 (quattro 2427) 4041746 (quattro 738)1209 1412 1221 950 9006762 Vehicle identificationAUDI HUNGARIA MOTOR KFT TRUZZZ8NZX1000301 1765 kg kg 11015 kg 2850 kg Typ 8N 1 1000 2111008*TRUZZZ8NZX1000301*Key of manufacturing plants within the Group in digit position 11: A Ingolstadt N Neckarsulm 1 Györ X Poznan K Karmann/RheineWorld manufacturing codePart describing vehiclePart identifying vehicleFiller constant = ZDigits 1 + 2 vehicle class. acc. to structure tableModel year, alphanumeric as prescribed by law Manufacturing plant within the Group (as at 04/94) Serial No. beginning with:1 Audi Hungaria Motor Kft: TT/TTS Audi AG: A3 A4 A6 (incl. SKD Poland) A8 Cabrio Audi 100 (C3, CKD) * * * * * * W W W W W W * T2 R A A A A A A3 U U U U U U U4 Z Z Z Z Z Z Z5 Z Z Z Z Z Z Z6 Z Z Z Z Z Z Z7 8 8 8 4 4 8 48 N L D B D G 49 Z Z Z Z Z Z Z10 X X X X X X X11 1 A A N/X N K A12 0 0 0 0 0 0 013 0 0 0 0 0 0 014 0 0 0 0 0 0 015 0 0 0 0 0 0 016 0 0 0 0 0 0 017 1 1 1 1 1 1 1*Vehicles to US specification (USA, Canada, Saudi Arabia, tourists) On the VIN (behind the windscreen), the certification label and on official documents, the fillers (Z) are replaced by a vehicle code (digits 4-8) or by a test mark (digit 9). This (18-digit) number is the official vehicle identification No. (VIN) in the countries listed above.7 A brief introduction to the TTEnvironmentally-friendly productionProduce locally - think global: Environmental protection is firmly rooted in Audi’s corporate strategy. During the vehicle development process, all environmental criteria are incorporated into the product and production concept from the outset. Economic goals and ecological needs are balanced so that no conflicts of aims arise. Audi lays great store by waste avoidance, reduction and recycling. – Almost all production resources and supplied parts are delivered in re-usable packaging. Most sheet-metal blanks are designed so as to minimise cutting waste after pressing.–Waste avoidance and reduction From 1998 onwards, Audi will use only watersoluble paints in a effort to make its production process more environmentally-friendly. This step will see a dramatic reduction in solvent emissions. Today’s fillers and base coats, for example, contain up to 45% solvent. By comparison, the solvent content in water-soluble systems is only about 6%.Recycling The recycling rate at Audi is now about 94% by weight. Metal cuttings from the press plant are used to manufacture small parts as far as possible. The resulting scrap is returned to the steelworks, where steel and zinc are separated from one another. Other waste materials such as paper, cardboard, timber, polystyrene, etc. are collected separately and fully recycled .8 BodySpecial featuresFront bumperSSP207/74The front bumper comprises two parts: the cover panel and a decorative grille. The bumper carrier is made of aluminium and bolted to the side members by impact absorbing elements.The guide profiles attached to the left and right wings ensure an even gap all round. A zero joint is created by attaching the bumper to the wing by means of threaded bolts as well as nut and washer combinations.Rear bumperSSP207/75The rear bumper comprises a total of 4 parts: the bumper panel, the rear cover, the aluminium cross-member and the central locating element.The rear cover is available in two versions depending on engine variant (TT has one tailpipe, the TTS two). A seamless transition to the body side section (zero joint) is produced by means of 2 bolts on each body side section.9 BodyBonnetThe bonnet is made of aluminium to save weight.SSP207/78Tailgate The tailgate can only be opened from the interior by means of the switch in the central console or by radio-wave remote control. The tailgate does not have a lock cylinder or a handle. The tailgate has a single-joint hinge.SSP207/77If the electrical system fails, the tailgate can be released in an emergency by means of the cable pull located below the rear central console cover.SSP207/76 10 DoorsSSP207/47The doors of the Audi TT Coupé are frameless and of two-piece construction. The door panel is made of steel with a bolted high-strength side reinforcement integrated in the door. Fuel filler flapThe door component carrier is made of aluminium and can be adjusted for length, height and inclination. Additional side protection pads protect the pelvis area.The fuel filler flap is made of aluminium. It can only be opened electrically via a switch in the central console. The fuel filler flap is attached from the exterior with three anti-theft-protected bolts plus four decorative bolts. If the electrical system fails, the fuel filler flap can be opened via an emergency release mechanism in the luggage compartment. For this purpose, it is necessary to open the flap in the side trim panel on the right-hand side of the luggage compartment and pull the cable in the direction indicated on sticker.SSP207/72Taillights To replace the filament lamps, the complete taillight unit is removed without needing any tools. Flaps are attached to the luggage compartment linings on the left and right. The light cluster is secured on the inside by means of 2 captive knurled bolts. On the outside, the taillight is engaged in a ball head.The light cluster can be adjusted along the vehicle’s longitudinal axis by means of the threaded sleeves.SSP207/56 11 BodyDash panelSSP207/79When removing the cross-tube, please note that one of the fastening bolts is located on the outside in the plenum chamber. To remove this bolt, it is necessary to remove the wiper linkage.StructureSSP207/15The vehicle front-end area deforms in a predefined manner, absorbing the impact energy without impairing the stability of the occupant cell. The side members are manufactured from 2-, 3- and 1.5-mm-thick mash-welded metal plates. In the case of a side impact, the strong cross members will also deform on the side of the body facing away from the impact to absorb some of the impact energy.The body structure of the vehicle rear-end area is designed in such a way that, firstly, the integrity of the fuel system remains largely intact and, secondly, the load on the occupants is kept to a minimum even in serious accidents. The Audi TT Coupé therefore complies with the statutory crash requirements as well as the laws relating to frontal and side impacts due to enter into effect in the EU and USA.12 B-pillar To absorb the load resulting from a side impact, the body structure is extremely rigid even though the B-pillar is not continuous. An additional transverse support extending from base of the B-pillar to the rear seat crossmember minimises cell deformation and the rate of intrusion into the side structure. This leads to low occupant loads.SSP207/9Side reinforcements in the doorsSince the deformation path for energy absorption is very limited during a side impact, various design measures are necessary to perform this task effectively. These include the side reinforcements made of high-strength extruded aluminium sections in the doors. The double-rectangular section can absorb large mounts of energy . During a side impact, the forces acting on the vehicle are distributed via the side reinforcements in the doors to the sill and the A- and Bpillars.SSP207/5Door sillThe strong sill also absorbs energy and simultaneously transmits this energy to the stable floorpan assembly. The sill trim is made of steel and is secured to the sill with 17 bolt + washer combinations.SSP207/45Be careful when placing the car on a lift support, otherwise the door sill may become dented.13 Vehicle safetyOccupant protectionThe Audi TT Coupé has head-thorax side airbags for the driver and front passenger. These side airbags are integrated in the seat backrests and extend from the rib cage area up to the head when inflated. When the side airbag is tripped, the head and neck areas are thus provided with better protection. In the Audi TT Coupé, the belt tensioners can be fired independently of the airbags depending on how the trigger criteria are defined.SSP207/80The Audi TT Coupé has a disable function for deactivating the front passenger airbag. When using Reboard child seats on the front passenger seat, the driver must disable the front passenger airbag with the vehicle key via the key switch located inside the glove box (see Operating Manual Audi TT Coupé).SSP207/81A yellow indicator light in the central console indicates when the airbag is deactivated.14 During a side impact, the vehicle occupant is inevitably subjected to a relative movement towards the force application point and away from the deformation path. Therefore, it is very important to ensure that the contact surface between the occupant and the vehicle is large and energy-absorbing. The side protection paddings made of plastic foam protect the vehicle occupants in the pelvis and rib cage areas.SSP207/6Deformation elementRoof paddingFor protection of the head, a padding is also integrated in the roof area. An additional deformation element has been welded onto the A-pillar. These measures have enabled Audi to comply with the new US head impact laws for the first time.SSP207/7The rear seat has been approved as a Group 3 child seat (approx. 6 - 12 years) and is compliant with ECE-R44. Children of heights ranging from 1.30 m to 1.50 m without raised seat swab.SSP207/73 15 Vehicle safetyTo minimise the risk of foot injuries in serious head-on collisions, the brake pedal is swung away from the foot area by means of a collapsing support if severe deformation of the vehicle occurs. This function is determined by deformation of the engine bulkhead and is not dependent on operation of the brake pedal.In the event of a frontal crash, the foot controls are displaced towards the central tube. This causes the collapsing support to deflect and the piston rod to buckle.The pedal footplate is swung up to 170 mm away from the foot area. The buckling of the piston rod and the deformation work resulting from this dampens the angular movement of the braking foot. This reduces the acceleration forces (braking foot) which normally arise considerably.SSP207/12616 Fuel cut-offThe fuel tank is made of plastic and is housed in a protected position in front of the rear axle. The central locking control unit receives this signal simultaneously and unlocks the vehicle doors. The hazard warning lights are activated automatically and the interior lighting is switched on. A restart function enables the engine to be restarted after an accident and it can be moved from the danger zone under its own power.The Audi TT Coupé is the first Audi to be equipped with a fuel cut-off. In connection with an airbag trigger mechanism (crash signal output), the Motronic control unit switches the fuel pump off.J234Airbag control unitJ220Motronic control unitJ17Fuel relayJ379Central locking control unit and anti-theft warning systemE3Hazard warning switchF220...223Door locking unit Interior lightingG6Fuel pump17 Drive unitsEngine and gearbox combinationsEngine Gearbox CodeMQ 250 5-speed front 02J.NDZF1.8-ltr. 5V turbocharged AJQ 132 kW/180 bhpSSP207/53MQ 350 5-speed quattro 02M.3DXWSSP207/131.8-ltr. 5V turbocharged APX 165 kW/225 bhpSSP207/33MQ 350 6-speed quattro 02M.1DQBSSP207/33 SSP207/14 18 1.8-ltr. 5V turbocharged engine 132 kW AJQSpecifications Engine code: Type: AJQ 4-cylinder 5-valve four-stroke petrol engine with exhaust gas turbocharger Double overhead camshaft (DOHC) 1781 cm3 81 mm 86.4 mmValve timing: Displacement: Bore: Stroke: Compression ratio: Torque:SSP207/139.5 : 1 235 Nm at 1950 - 4700 rpm Rated output: 132 kW/180 bhp at 5500 rpm Engine management: ME 7.5 Fuel: Premium unleaded 98 RON (RON 95 can be used, but reduces power output)200400Technical modifications: Basic 110 kW (150 bhp) – – –Torque [Nm]180360160320Output [kW]140280120240– – –100200EU II + D3 electronic throttle control “Tumble“ duct (For details of the tumble duct in the intake system, refer to SSP 198) Engine control unit (characteristic curves adapted) CAN-BUS with TCS/EDL/ESP electr. activated air divert control valve8016060120408020400 1000 2000 3000 4000 5000 6000 70000Engine speed [rpm]SSP207/6219 Drive unitsSystem overview – 1.8-ltr. 132 kW 5V turbocharged Sensors Hot-film air mass meter G70Engine speed sender G28Hall sender G40Lambda probe G39Throttle valve control unit J338 with angle sender G187 for throttle valve gear G186Intake air temperature sender G42 Coolant temperature sender G2 and G62Knock sensor 1 (cyl. 1 - 2) G61 Knock sensor 2 (cyl. 3 - 4) G66Accelerator pedal module with accelerator position sender G79 and G185Brake light switch F and brake pedal switch F47 Clutch pedal switch F36 Auxiliary signals: Pressure switch for power steering F88 Cruise control Intake manifold pressure sender G7120 ActuatorsFuel pump relay J17 and fuel pump G6Injection valves N30, N31, N32, N33Power output stage N122 and ignition coils N (1st cyl.), N128 (2nd cyl.), N158 (3rd cyl.) and N163 (4th cyl.) with integrated power output stageSolenoid valve for activated charcoal canister N80Solenoid valve for charge pressure limitation N75Throttle valve control unit J338 with throttle valve gear G186Air recirculation valve for turbocharger N249Heater for lambda probe Z19 Fault lamp for electronic throttle control K132 Auxiliary signalsSSP207/46 21EPC Function chartTurbocharged 1.8-ltr. 132 kW 5V engine Motronic ME 7.5 Components A Battery E45 Switch for cruise control system E227 Button for cruise control system F Brake light switch F36 Clutch pedal switch F88 Power steering (pressure switch) G6 Fuel pump G28 Engine speed sender G39 Lambda probe G40 Hall sender with quick-start sender wheel G42 Intake air temperature sender G61 Knock sensor 1 G62 Coolant temperature sender G66 Knock sensor 2 G70 Air mass meter G71 Intake manifold pressure sender G79 Accelerator position sender G186 Throttle valve gear (electronic throttle control) G187 Throttle valve drive angle sender 1 G888 Throttle valve drive angle sender 1 J17 Fuel pump relay J220 Motronic control unit K132 Fault lamp for electronic throttle control M9/10 Stop lights N Ignition coil N30...33 Injection valves N75 Solenoid valve for charge pressure limitation N80 Solenoid valve for activated charcoal canister N128 Ignition coil 2 N158 Ignition coil 3 N163 Ignition coil 4 N249 Air recirculation valve for turbocharger P Spark plug socket S Fuse Q Spark plugs Z19 Heater for lambda probe Auxiliary signals CAN-BUS H = CAN-BUS L = A B C D E F G}Databus driveEngine speed signal (out) Fuel consumption signal (out) Road speed signal (in) Air-conditioner compressor signal (in-out) Air conditioning ready (in) Crash signal (in) from airbag control unit Alternator terminal DF/DFM (in) W- line (in-out)For the applicable Fuse No. and amperage, please refer to the current flow diagram.Input signal Output signal Positive Earth Bidirectional22 30 1530 158630J17 48587S SN N158 N128SSSSSSSQ PQ PQ PQ PN163E45 F F36 N75 N249 G70 N80E227Z19G39A B C DλN30 M9/1015 55 49 14 9N31N32N33+A +J220 J220+- -+A+ +MPG40 G62 F88G28 G61 G66 G42ECAN - BUS H CAN - BUS LFGK132G186G187G188G79G71MG63131SSP207/2523 Dieses Dokument wurde erstellt mit FrameMaker 4.0.4. Drive unitsChargingDirection of travel5V Turboenergised de-energisedN249SSP207/20The turbocharging system comprises the following components: – – – – Exhaust emission turbocharger Charge air cooler Charge pressure control Air divert control in overrunThe result is an increase in power output for the same displacement and engine speed. In the case of the 1.8-ltr. 5V turbocharged engine, turbocharging is also used to provide high torque from the bottom end to the top end of the rev band. Charge pressure increases in proportion to the turbocharger speed. The charge pressure is limited to prolong the life of the engine. The charge pressure control performs this task. The air divert control prevents the turbocharger slowing down unnecessarily if the throttle valve closes suddenly.The flow energy of the exhaust emissions is transferred to the fresh air entering the exhaust gas turbocharger. In the process, the air required for combustion is compressed and the volume of air entering the cylinders per working cycle is thus increased. The air temperature, increased by compression, is again reduced in the charge air cooler. Since the density of the cooled air is higher, the amount of fuel-air mixture entering the engine is greater, too.24 Charge pressure controlJ220N75 Waste gate valve G70 G28 G695V Turboenergised de-energised N249 SSP207/22The engine control unit calculates the charge pressure setpoint from the engine torque request. The engine control unit regulates the charge pressure as a function of the opening time of the solenoid valves for charge pressure limitation N75. For this purpose, a control pressure is generated from the charge pressure in the compressor housing and the atmospheric pressure. This control pressure counteracts the spring pressure in the charge pressure control valve (vacuum box) and opens or closes the waste gate valve in the turbocharger. In the de-energised state, the solenoid valve N75 is closed and the charge pressure acts directly on the vacuum box. The charge pressure control valve opens at low charge pressure.If the control fails, the maximum charge pressure is limited to a basic charge pressure (mechanical charge pressure). If the bypass is closed, the charge pressure rises. In the lower engine speed range, the turbocharger supplies the charge pressure required to develop high torque or the required volume of air. As soon as the charge pressure has reached the calculated charge pressure, the bypass opens and a certain quantity of exhaust gas is ducted past the turbine. The turbocharger motor speed decreases, and so too does the charge pressure. For more detailed information regarding charge pressure control, please refer to SSP 198.25 Drive unitsAir divert control in overrunAir recirculation valve (pneumatic)5V Turboenergised de-energisedN249SSP207/23When the throttle valve is closed, it produces a backpressure in the compressor circuit due to the charge pressure still present. This causes the compressor wheel to decelerate rapidly. When the throttle valve is opened, the speed of the turbocharger must again be increased. The air divert control in overrun prevents turbo lag, which would otherwise occur. The air recirculation valve is a mechanically activated and pneumatically controlled spring diaphragm valve. It is also activated via an electrically activated air recirculation valve for turbocharger N249. This, in connection with the vacuum reservoir, enables the air recirculation valve N249 to operate independently of the intake manifold pressure. If the air recirculation valve fails, control takes place as a result of the engine vacuum downstream of the throttle valve.26As soon as the throttle valve is closed, the air recirculation valve briefly closes the compressor circuit. The vacuum counteracts the spring in the valve. The valve opens, and the compressor and intake sides of the compressor circuit close for a short period of time. There is no deceleration of the compressor wheel. When the throttle valve re-opens, the intake manifold vacuum drops. The air recirculation valve is closed by the spring force. The compressor circuit no longer closes briefly. Full charger speed is available immediately. For more detailed information regarding the air divert control in overrun, please refer to SSP 198. 1.8-ltr. 5V 165 kW APX turbocharged engineSpecifications Engine code: Type: APX 4-cylinder 5-valve four-stroke-petrol engine with exhaust gas turbocharger Valve timing: Double overhead camshaft (DOHC) Displacement: 1781 cm3 Bore: 81 mm Stroke: 86.4 mm Compression ratio: 9 : 1 Rated output: 165 kW at 5900 rpm max. torque: 280 Nm at 2200 to 5500 rpm Engine management: ME 7.5 Fuel: Premium unleaded 98 RON Exhaust gas treatment: Twin-flow catalytic converter, one heated lambda probe upstream and downstream of the catalytic converter Technical modifications: Basic 132 kW (180 bhp) – – –Torque [Nm]SSP207/14200400180360160320Output [kW]140280120240– –1002008016060120– – – – –40802040–0 1000 2000 3000 4000 5000 6000 7000 0Cooling water afterrun pump (approx. 10 min) Secondary air system Piston (modified), thus changing the compression ratio to 9.0 : 1 from 9.5 : 1 Manifold (new exhaust and flange) When EU III takes effect, there will be a 2nd lambda probe downstream of catalytic converter for catalyst monitoring 2 in-line charge air coolers Injection valves (higher flow) Quick-start sender wheel Piston cooling by oil injectors (volumetric flow adaptation) Hot-film air mass meter with reverse flow detector HFM5 integrated in the intake air filter upper section Single-flow throttle valve unit integrated in the electronic throttle control positionerEngine speed [rpm]SSP207/63 27 Drive unitsExtended system overview - 1.8-ltr. 165 kW 5V engineLambda probe downstream of catalytic converter G130 when EU III takes effectMotronic control unit J220Secondary air pump motor V101Secondary air pump relay J299Secondary air injection valve N112SSP207/103Heater for lambda probe down-stream of catalytic converter Z29 when EU III takes effectThe secondary air system in the 1.8-ltr. 5V engine developing 165 kW ensures that the exhaust emissions comply with the EU III+D3 standard. A probe will be installed downstream of the catalytic converter to meet the requirements stipulated in EU III.28 Extended function diagram - 1.8-ltr. 165 kW 5V engine30J17SSJ299 Z29 G130 N112V101MλJ220HK31SSP207/27As of series production launch, the 1.8-ltr. 165 kW engine will be equipped with extended system components to ensure it complies with European exhaust emission standard EU II + D3. The basic version is equivalent to the engine management system used in the 1.8-ltr. engine developing 132 kW (refer to function diagram).LegendG130 Lambda probe downstream of catalytic converter when EU III comes into effect Fuel pump relay Secondary air pump relay Secondary air injection valve Secondary air pump motor Heater for lambda probe downstream of catalytic converter when EU III comes into effect Air conditioning PWM signal Fault lampJ17 J299 N112 V101 Z29H K29 Drive unitsQuick-start sender wheelThe quick-start sender wheel is attached to the camshaft. It supplies a signal which enables the engine control unit to determine the position of the camshaft relative to the crankshaft more quickly and, in combination with the signal which the engine speed sender supplies, to start the engine more quickly. On previous systems, it was not possible to initiate the first combustion cycle until a crank angle of approx. 600˚ - 900o was reached. The quick-start sender wheel enables the engine control unit to recognise the position of the crankshaft relative to the camshaft after a crank angle of 400˚ - 480o. This allows the first combustion cycle to be initiated sooner and the engine to start more quickly.Track 1Twin-track sender wheelTrack 2ToothGap Hall device Track 1Hall device Track 2 SSP207/84 Hall sensorThe quick-start sender wheel comprises a twin-track sender wheel and a Hall sensor. The sender wheel is designed so that two tracks are located side by side. In the position where there is a gap in one track, there is a tooth in the other track.30 The control unit compares the phase sensor signal with the reference mark signal and thus ascertains the working cycle currently taking place in the cylinder. Low phase signal High phase signal = = Compression cycle Exhaust cycleSSP207/85The signal which the engine speed sender G28 supplies enables the injection cycle to be initiated after a crank angle of approx. 440o.SSP207/86Electrical circuit The Hall sender G40 is connected to the sensor earth terminal of the engine control unit.J220G71 2 1Even if the Hall sender fails, it is still possible to start the engine.G403SSP207/8731 Drive unitsCooling circuitCoolant afterrun pumpCoolant temperature sender G2/G62 Heating heat exchanger Exh. gas turbochargerExpansion tankCylinder headCoolant pumpCoolant regulatorCoolant afterrun pump V51Oil cooler Thermoswitch for radiator fan F18/F54SSP207/37 CoolerThe exhaust gas turbocharger is water-cooled and integrated in the cooling circuit. When the coolant regulator is open, the coolant flows back to the cooler or coolant pump via cylinder head, exhaust gas turbocharger and coolant afterrun pump, among others.The coolant afterrun pump protects the coolant against overheating, e.g. after turning off a hot engine.32 Coolant afterrun pump V51SSP207/38Function in vehicle with air conditioning The coolant afterrun pump V51 is attached to the radiator fan housing. The pump starts via radiator fan control unit J293 when the ignition is turned “On“. A timer module integrated in the control unit J293 ensures that the pump V51 runs on for approx. 10 min after the ignition has been switched off. In vehicles without air conditioning, these functions are implemented by means of a timer relay.To counteract the thermal loads, and in particular at the exhaust gas turbocharger, the pump V51 starts up when the ignition is turned “On“.33 Drive unitsCharging5V TurboSSP207/24To increase the power output and torque of the 1.8-ltr. 5V engine to 165 kW, it was necessary to make various design modifications to the basic engine of the Audi TT Coupé developing 132 kW. A characteristic feature of the engine is its higher air demand, making it necessary to enlarge the diameter of the intake port and exhaust gas turbocharger.Since the previous charge air cooler was no longer capable of effectively cooling down the increased air flow through the exhaust gas turbocharger, it was necessary to accommodate a second, parallel charge air cooler on the left-hand side of the vehicle.34 Secondary air systemVacuum box for charge pressure control valveCombi-valve5V Turboenergised de-energised G39 G62 J299 N122 V101J220SSP207/21In the cold start phase, the exhaust gases contain a high proportion of uncombusted hydrocarbons. To improve the exhaust gas composition, these constituents must be reduced. The secondary air system is responsible for this task. The system injects air upstream of the outlet valves during this phase, thus enriching the exhaust gases with oxygen. This causes postcombustion of the uncombusted hydrocarbons contained in the exhaust gases. The catalytic converter reaches operating temperature more quickly due to the heat released during postcombustion.The vacuum box for the charge pressure control valve is controlled in the cold start phase by the electro-pneumatic secondary air control valve N112 while the secondary air system is in operation. The control pressure acts on the turbocharger waste gate, and the exhaust gas flow is routed past the turbine wheel up to the upper load range. The hot exhaust gases help the secondary air system to quickly heat the catalytic converter up to operating temperature during the cold start phase.35 Drive unitsSecondary air injection valve N112 The secondary air injection valve is an electropneumatic valve. It is switched by the Motronic control unit and controls the combi-valve. To open the combi-valve, the secondary air injection valve releases the intake manifold vacuum. To close the combi-valve, the secondary air injection valve releases atmospheric pressure.SSP207/16Secondary air pump V101 The secondary air pump relay J299 which the Motronic control unit drives switches the electric current for the secondary air pump motor V101. The fresh air which is mixed with the exhaust gases is drawn out of the air filter housing by the secondary air pump and released by the combi-valve.SSP207/17The combi-valve The combi-valve is bolted to the secondary air duct of the cylinder head. The air path from the secondary air pump to the secondary duct of the cylinder head is opened by the vacuum from the secondary air injection valve. This valve also prevents hot exhaust gases entering and damaging the secondary air pump.Valve openedValve closedFresh air from secondary air pumpVacuum in control line from secondary air injection valveAtmospheric pressure in control line from secondary air injection valveTo secondary air portSSP207/19Exhaust gasSSP207/1836 Subsystems of the MotronicLambda control in EU III 165 kWLambda control in the EU III An additional lambda probe (G130), which is located downstream of the catalytic converter, was integrated in the system to comply with EU III. Its purpose is to test the function of the catalytic converter. Depending on vehicle type, the connectors, plug colours and fitting locations are different to help identify the connectors correctly.SSP207/100What is the purpose of the EU III test? An aged or defective catalytic converter has a lower oxygen storage capacity, which also means that its conversion efficiency is poorer. If the applicable limit values for hydrocarbon content in the exhaust gases are exceeded by a factor of 1.5 in the course of a statutory exhaust emission test, this must be identified via the fault memory.Catalytic conversion diagnosis During the diagnosis, the engine control unit compares the probe stresses upstream and downstream of the catalytic converter probe and calculates an upstream-to-downstream ratio. If this ratio deviates from the nominal range of values, the engine management recognises that the catalytic converter has malfunctioned. After the fault conditions have been fulfilled, the appropriate fault code is saved to the fault memory.Electrical circuitJ220+1234Effects of signal failure The engine lambda control also operates if the probe downstream of the catalytic converter fails. The only function which is unavailable if the probe fails is the catalytic converter function test. In this case, the Motronic cannot execute a functional test on the probe upstream of the catalytic converter either. See SSP 175 – On-Board Diagnosis II.G130SSP207/10137 Subsystems of the MotronicTorque-oriented engine managementThe Motronic ME 7.5 has a torque-oriented functional structure. The new electronic throttle control function makes this possible. External and internal torque requests are coordinated by the engine control unit, making allowance for efficiency and implemented with the available manipulated variables.Internal torque requests •• • •StartIdling control Catalytic converter heating Power output limitation Driving comfort Component protection Engine speed limitationExternal torque requests• • • Driver input •Torque-influencing manipulated variables•Driving dynamicsCo-ordination of torque and efficiency requests in the engine control unitThrottle valve angleCharge pressure•Driving comfortIgnition angle•Cruise control systemCylinder suppressionInjection timeSSP207/96 38 Torque-oriented functional structure In contrast to previously known systems, the ME 7.5 is not limited to the output of torque variables to the networked control units (ABS, automatic gearbox). Instead it refers back to the basis of this physical variable when it calculates the manipulated variables. All - internal and external - torque requests are combined to form a nominal torque. To implement the nominal torque, the manipulated variables are co-ordinated, making allowance for consumption and emission data so as to ensure optimal torque control.Charge torque setpointSetpoint chargeCharge path prioritisationConversion of torque into charge Throttle valve angleThrottle position calculation Actual charge Calculation of efficiency and torque reference variablesIntake manifold pressure setpoint Charge pressure controlExternal and internal torque requestsCharge pressure (waste gate)Ignition angle Prioritisation of crankshaft-synchronous path Calculation of crankshaftsynchronous initiationsCylinder suppression Injection timeInner torque setpointSSP207/9739 Subsystems of the MotronicAccelerator position senders G79 and G185The accelerator position sender transmits the driver inputs to the Motronic. The accelerator position sender transmits to the Motronic an analogue signal corresponding to the accelerator pedal position. To ensure the functional reliability of the electronic throttle control, the accelerator position sender has two independent potentiometers G79 and G185. The characteristics are different (refer to diagram). The control unit monitors the function and plausibility of the two senders G79 and G185. If a sender fails, the other sender acts as a back-up.SSP207/102 Resistance in Ω G79 G185LHDAccelerator pedal travelModule housingHousing cover with sensorsThe electronic throttle control function is used to reduce and increase torque without adversely affecting the exhaust emission values.SSP207/98Torque reduction• • • • • • Traction control Engine speed limitation Speed limitation Power output limitation Cruise control system Driving dynamics control systems • • • • •Torque increaseSpeed control Engine braking control Dash pot function Idling control Driving dynamics control systems40 Electrically actuated throttle valve (electronic throttle control function)With Motronic ME 7.5, there is no longer a mechanical throttle control cable between the accelerator pedal and throttle valve. This has been replaced by an electronic control unit (drive-by-wire). The driver input at the accelerator pedal is registered by the accelerator position sender and transmitted to the engine control unit. The engine control unit positions the throttle valve via an electric motor. The engine control unit is provided with continuous feedback on the throttle valve position. Extensive safety measures have been implemented in the hardware and software. For example, dual senders, a safety module and a self-monitoring processor structure are integrated in the electronic throttle control function.The system comprises the following components: – – – Accelerator position sender Engine control unit Throttle valve control unitThrottle valve control unit J338 Engine control unit Input signals Accelerator position sender Output signalsThrottle valve drive G186CPU*SSP207/99 Accelerator pedal position senders G79 and G185 * Control Processing Unit Angle senders for throttle valve drive G187 and G188Safety module41 Fuel systemFuel tanks for vehicles with front-wheel drive and quattro power train Different fuel tanks are used in the front-wheel drive and quattro versions of the Audi TT. Both fuel tanks are made of plastic and have a capacity of 55 ltr. and 62 ltr. in the front-wheel drive and quattro versions respectively. The filler neck cannot be separated from the fuel tank.Air vent valve for vehicles with front-wheel drive and quattro power trainBypass duct Housing for gravity float valveActivated by unleaded fuel valve Air vent valveFiller neckFiller expansion tank Main expansion chamber SSP207/116When refuelling the vehicle, the unleaded fuel valve activates the air vent valve. The valve seals the main expansion chamber so that no fuel vapour can escape from this tank when the vehicle is being refuelled. The filler expansion chamber is vented by the filler neck.In the US version and after EU III takes effect, fuel vapours will be routed to the ACF system by an additional vent line connected to the air vent valve while the vehicle is being refuelled.42 Gravity float valves for vehicles with frontwheel drive and quattro power trainFiller expansion chamberMain expansion chamberto ACF systemSSP207/117The gravity float valve prevents fuel from entering into the ACF system when cornering at high speed or if the vehicle rolls over.The filler expansion chamber as well as the main expansion chamber are combined at the filler neck upper section and purged via the gravity float valve by the ACF system.43 Fuel systemFuel tank for front-wheel drive versionAir vent valve Gravity float valve Filler expansion chamber Filler neck Main expansion chamberto activated charcoal filter Filler breatherMain breather SSP207/118When refuelling the fuel tank, the gas mixture is conveyed via the filler breather directly into the filler expansion chamber and from here via the filler neck into the atmosphere. Heat-induced fuel vapours are channelled through the operating vent and collected in the main expansion chamber at the filler neck upper section.The vapours are conveyed to the activated charcoal filter via the closed filler neck, the bypass at the air breather valve and the gravity float valve.44 The fuel is transferred to the engine by a highperformance fuel pump with a pressure increase from 3 to 4 bar. In the event of a crash, the fuel pump is switched off by the fuel pump relay. A single-stage fuel pump is used in vehicles with front-wheel drive.SSP207/119Electrical circuit30 15 X 31 30 15 X 31Components G G1 G6 J17 J218 J220 S Fuel gauge sender Fuel gauge Fuel pump Fuel pump relay Combi processor in dash panel insert Motronic control unit FuseJ17J220 S G1J218 G6 M G3131SSP207/5545 Fuel systemFuel tank for quattro vehicles The breather system is designed in the same way as for front-wheel drive vehicles.Air vent valveFiller expansion chamber Gravity float valve Main expansion chamberFiller neck Main breatherFiller breather SSP207/120Located in the quattro fuel tank on the lefthand side is a suction jet pump which pumps the fuel from the left-hand fuel tank part upstream of the baffle housing of the fuel delivery unit.46 SSP207/121The suction jet pump is driven by the twostage fuel pump. The suction jet pump can only be removed after de-taching the fuel lines and tank sender from the baffle housing. Electrical circuit30 15 X 31 30 15 X 31The fuel lines and left-hand tank sender are connected to the baffle housing in the tank.Components G G1 G6 G169 J17 J218 J220 S Fuel gauge sender Fuel gauge Fuel pump Fuel gauge sender 2 Fuel pump relay Combi processor in dash panel insert Motronic control unit 2 FuseJ17J220 S G1G169 J218 G6 M GThe tank senders are connected in series. R1 + R2 = Rtotal Signals are evaluated in the dash panel insert microprocessor.3131SSP207/82The senders can be accessed via two openings below the rear seat. For removing and installing the senders, please follow the instructions given in the Workshop Manual.47 Power transmissionThree gearbox variants are used for power transmission:132 kWAJQ5-speed front-wheel drive 5-speed quattro drive2-shaft gearbox02J.N 02M.3165 kWAPX6-speed quattro drive}3-shaft gearbox02M.1Technical features of the gearboxes The 5-speed and 6-speed quattro gearboxes are identical as regards their design, whereby the change gear for 6th gear in the 5-speed gearbox has been replaced with a spacer sleeve. 4 manual shift gates are used for the 5- and 6speed variants (an optimal layout is possible for both versions). 5-speed manual gearbox Compared to the standard version (A3), the 5speed front-wheel drive version has a modified ratio, a re-inforced differential with flange shaft adaptation and triple roller joint shaft. The gearbox was modified in the selector shaft area (standardised gear change linkages used), and the gear lever of the sporty version of the TT has been adapted.SSP207/124 48 6-speed manual gearbox 3 shafts The triple-shaft design permits a space-saving and highly compact design. A distinction is made between two gearbox variants, the variant for vehicles with frontwheel drive and the variant for vehicles with four-wheel drive (quattro). Both variants differ from one another as regards their attachment points and oil penetration points. The use of magnesium as a housing material results in a weight reduction of 30% due to its lower density (aluminium has a density of 2.695 g/cm3 and magnesium has a density of 1.738 g/cm3).SSP207/5449 Power transmission3-shaft gearbox MQ 350 in 6-speed versionReverse gear2nd drive shaft Gears 5-61st drive shaft Gears 1-4Engine driveSpur gearSSP207/122The spur gear is riveted to the differential. If repair work is necessary, the spur gear must be bolts.For more detailed information on the manual gear-boxes, see SSP 205.50 Notes51 Power transmissionHaldex viscous couplingThe four-wheel power train used in the Audi TT Coupé quattro is a logical progression on the proven four-wheel drive concept. A new feature of the power train is the slipdependent force distribution control on both axles by means of a Haldex viscous coupling. The manual gearbox transmits the engine output directly to the front axle and simultaneously via an angle gear and the propshaft to the Haldex viscous coupling flanged to the rear axle drive. The rear axle drive is composed of the Haldex viscous coupling, the axle drive and the differential.SSP207/28The transmitted torque is dependent on the speed difference between the front and rear axles. Also, the torque transmission parameters are defined in the software (variable torque transmission control adapted to the driving situation).SSP207/29Advantages of the Haldex viscous coupling: – Permanent four-wheel drive is fully automatic for the driver Permanent four-wheel drive at engine speeds higher than 400 rpm – – Controllable four-wheel drive system, the characteristic curve is not constant – – High rear axle drive torque of up to 3200 Nm – – – Acceleration with high directional stability Handling is neutral with a slight tendency to understeer No restrictions on towing when the axle is raised off the ground Communication via CAN-BUS52 The system configurationPlate couplingCoupling output end (rear axle differential input) Piston of annular piston pump SSP207/11Input end (propshaft)Working pistonThe Haldex viscous coupling is accommodated in a closed housing and mounted in front of the rear axle drive. The input shaft and the output shaft are separate. These shafts are connected via a plate coupling running in oil. The coupling package comprises inner and outer plates, which are connected to the input shaft and output shaft respectively. Arranged around the shaft at the coupling input end are a working piston and two parallel annular piston pumps with a single annular piston each.The housing is filled with oil and hermetically sealed against the atmosphere. The plate coupling which runs immersed in oil represents a closed system. It has its own oil circuit, hydraulic components, an electrohydraulic control valve and an electrical control unit. The system is electrically linked to the onboard CAN databus. The rear axle is a rear differential.53 Power transmissionThe hydraulicsWorking piston Plate setTwo parallel annular piston pumps Pre-pressurising pumpMInputOutputCam discSafety valve Control valveOil fillingSSP207/12Torque is transmitted to the rear axle drive by means of the plate coupling . The necessary coupling pressure is generated via the two annular piston pumps. The annular piston (also known as axial piston) is driven by an axial piston pump. The speed at which this pump rotates is the difference between coupling input and output speeds. An even pressure curve is ensured by three phase-shifted pump strokes. The annular pistons runs in floating bearings. They are driven by the pressure generated by the pre-pressurising pump (an electrically driven gear pump). The pre-pressurising pump only operates if the ignition has been turned on and engine speed is greater than 460 rpm.In the event of a breakdown, this means that the vehicle can be towed without the engine running and with the axle raised off the ground. Torque is developed at the coupling depending on the driving situation. Pressure modulation is induced by means of the control valve (hydraulic proportional valve), whose opening cross-section is altered by a slide valve. The slide valve is activated by a rack and a stepping motor. The control unit together with its software are located in the immediate vicinity of the stepping motor. A safety valve opens at very higher inner pressure to prevent the coupling from being damaged.54 The control systemLow coefficient of friction Wheel speed front right front left Wheel speed rear right rear left Engine control unitMB MAMdMAHaldex control unit Haldex viscous couplingABS/EDL hydraulic unitMAMASSP207/10 Motive force, front ABS/EDL control unit Motive force, rear High coefficient of frictionThe Haldex viscous coupling does not have any sensors of its own apart from a temperature sensor (necessary for compensating for temperature-dependent oil viscosity). The system conditions the signals which the CAN-BUS supplies (ABS/EDL control unit, engine control unit). These are – speed of each individual wheel – engine torque – engine speed – driving condition (straight-ahead driving, thrust, braking, ABS) – accelerator pedal position/throttle valve The control system can recognise corners, manoeuvring mode, acceleration phase and different wheel circumferences. The stiffness of the Haldex viscous coupling is adjusted according to the recognised driving conditions.Legend ABS/EDL sensor line ABS/EDL control line Brake line, pressurised Brake line, depressurised Drive torque per wheel Brake torque per wheel Engine torque Accelerator pedal position, Engine torque, Engine speed Wheel speedsMA MB MdIf faulty signals are generated or if CAN messages cannot be received, the vehicle switches to emergency mode. If speed signals are missing, the coupling is opened fully for safety reasons.The Haldex viscous coupling is integrated in the vehicle self-diagnosis. Address word: 22 – 4wd electronics.55 Running gearSteeringThe safety steering column is adjustable for rake and reach as standard.SSP207/2The maintenance-free rack and pinion steering gear is power-assisted. The steering gear stroke is transmitted directly to the swivel bearing due to the fact that the track rods are optimally attached to the steering arm. Consequently, the steering is direct. A steering damper reduces the influence of impacts and vibrations which are transmitted from the wheels to the steering gear.The vibration-optimised attachment of the steering column to the dash panel cross-member keeps the steering wheel free of undesirable vibrations.56 Pressure switch for power steering The pressure switch for power steering is located on the vane pump. It informs the engine control unit when the vane pump is subjected to a load. The vane pump is driven by the engine by means of a the ribbed V-belt. At full steering lock, the vane pump generates a pressure. This also places a higher load on the engine, and idling speed can drop sharply. The signal which the pressure switch generates enables the engine control unit to recognise engine loading in time and to regulate engine torque at idling speed.SSP207/113This is how it works: As steering forces increase, the pressure switch closes and sends a signal to the engine control unit. Without steering wheel movement, the pullup integrated in the engine control unit is at +5 V. When the pressure switch is closed, the engine is connected to earth. The ME 7.5 determines itself how engine torque is to be increased at idling speed, in order to counteract the load (e.g. ignition angle correction towards “retard“).Electrical circuitComponents J220 F88 Engine control unit Pressure switch for power steeringF88 1 2J220SSP207/8357 Running gearFront axleIncorporating double wishbones, subframe and transverse anti-roll bar, the McPherson strut axle is designed as a sports suspension. To enhance track stability, newly developed cast steel-swivel bearing with modified track rod attachments as well as a new forged cross-member are used.Coupling link between suspension strut/anti-roll barTrack rod jointSubframeBall joint Steering gearThe features of the front axle are: – Track rod joints (larger diffraction angle)SSP207/3–Ball joint is reinforced by thicker journals– The subframe is rigidly bolted to the aluminium bush – The suspension strut attachment to the anti-roll bar ensures better response58 Rear axleFront-wheel drive Torsion beam axle with anti-roll barWheel housing supportWheel bearing Double ball bearing requiring no adjustmentPositioning inclined 25o25°25°SSP207/115– –Track width: 1507 mm Modified axle plates for increased camber and modified toe-in Track-correcting axle bearingThe shock absorbers are supported in the wheel housing and the coil springs are supported below the side member. The axle is stabilised by a tubular anti-roll bar.–The self-steering effect of the rear axle is more favourable thanks to the bearing inclination of 25o. Due to the rear axle inclination, the side forces which occur when cornering are transmitted favourably to the bearing and from the bearing to the body. Due to the separate layout of the springs and shock absorbers, the vehicle has a large luggage compartment and driving noise inside the passenger cabin is reduced (sound insulation).59 Running gearRear axleQuattro drive Dual link trailing arm axle (DLTA) with Haldex viscous couplingDamperAnti-roll bar SubframeRubber bearingHaldex viscous couplingTrailing armTrailing linkSSP207/4–The dual link trailing arm axle is fixed via the subframe (4-point attachment) and each of the track-correcting wishbones attached to the trailing link. For stabilisation purposes, a transverse anti-roll bar is located on the axle subframe. Fitting position of damper (approx. 45o)New tool for mounting rear wheel bearings.––60 Brake system132 kW Diagonal-split dual circuit brake system Anti-lock Braking System (ABS) with electronic brake force distribution (EBFD)Traction Control System (TCS)165 kWDisc brakes at front and rear Ventilated at front Brake servo 10“ 10“ Ventilated at front and rearSSP207/42–The electronic brake force distribution (EBFD) regulates the brake pressure acting on the rear wheels via the ABS control unit so that they cannot be overbraked. The EBFD control is suppressed when the ABS control takes effect. The electronic differential lock (EDL) provides assistance with driving away on slippery surfaces.Spinning wheels are braked automatically and the drive torque is diverted to the wheel which has traction. – The Traction Control System (TCS) prevents the driven wheels from spinning by reducing engine torque (by adjusting the ignition angle and intermittently switching off the injection valves).–61 Running gearAnti-lock Braking System ABS ITT/Mark 20 IEG45K47K14/33G44J104V64 N55FG47G46 SSP207/31 Output signals Input signalsFor a brief description of the components, please refer to function diagramBrake circuit Brake circuitThe basis of the ABS system is a dual-circuit brake system. The brake circuits are laid out diagonally and supply the front left, rear right, front right and rear left wheels. A separate brake line running from the 4-channel system of the hydraulic unit is assigned to each wheel.The EBPD is entirely software-supported and does not require any hardware.Fault recognition in the ABS system is via warning lamps (visual contact) and by means of the self-diagnosis (diagnostic unit).62 Electronic stability brake system - ESBS The electronic stability brake system improves the track stability and steerability of braked vehicles by applying each brake as required. It utilises the sensors and actuators of the ABS system. ESBS is a software development in the ITT Mark 20 IE control unit.Understeer If a vehicle understeers during a braking operation, this means that the maximum cornering grip of the wheels has been exceeded. The vehicle will slide towards the outside of the corner over the front axle. The ABS control unit recognises this situation from the circumferential speed of the wheel. The brake pressure acting on the front axle is thus reduced in order to increase cornering grip. The vehicle stabilises itself and follows the direction in which the vehicle is steered.SSP207/94 Brake application Vehicle movement when understeer occursOversteer If the vehicle oversteers during a braking operation, this means that the maximum cornering grip of the rear wheel has been exceeded. The vehicle breaks away towards the outside of the corner over the rear axle. The ABS control unit recognises this situation from the reduced circumferential speed of the rear wheels and reduces the braking force acting on the wheels on the inside of the corner. The guide forces acting on the inner wheels are increased and thus stabilised.SSP207/95 Brakes application Vehicle movement when oversteer occurs Vehicle vertical axis Yaw moment Counteracting yaw momentA functional fault of the ESBS can neither be diagnosed nor rectified, since the driving dynamics cannot be reconstr ucted with workshop equipment.63 ElectricsThe vehicle electrical systemThe electrical/electronic connector stations as well as the necessary control units are decentralised to meet the requirements. This ensures an optimum wiring configuration.Socket (power windows, radio, CLS-ATA light, mirror adjustment) Lateral acceleration sensor, passenger’s sideConnector point, A-pillarEngine control unit J220 Navigation operating electronics control unit J402 Immobiliser control unit J362 Combi processor in the dash panel insert J218Airbag control unit J234Radiator fan control unit J293 Fuse box, battery ABS-EDL control unit J104 64 Telephone operating electronics control unit J412Control unit for headlight range control J431Central locking control unit J429Control unit for navigation system and CD J401Lateral acceleration sensor, driver’s sideMicro-ZESocket (power windows, loudspeaker, radio, central locking, anti-theft alarm) Fuse carrier SSP207/112 Coupling point, A-pillar Mini-electrics 65 ElectricsInterior monitoringThe vehicle interior is monitored by an ultrasonic monitoring system. It gives the alarm audibly via the horn of the anti-theft warning system and visually via the hazard warning lights. The following requirements must be fulfilled to ensure that the interior monitoring functions properly: – – The vehicle must be closed on all sides There must be no additional air movement in the vehicle interior – The system is safeguarded against false alarms, e.g.: – knocking on the roof of the vehicle or against the window air movement caused by wind or passing vehicles temperature changes, e.g. due to the interior of the vehicle heating up as a result of exposure to strong sunlight any kind of noise (horns, sirens, bells).––The system communicates with the anti-theft warning system regarding activation/deactivation as well as tripping of the alarm. Located on the central console is the interior monitoring switch. It switches off the interior monitoring for a single locking operation.Sensor moduleCentral locking control unitAlarm hornSSP207/68 Interior monitoring switch66 Functional description The sensor unit comprises a sender, a receiver and the evaluation electronics. The sensor unit is located behind the interior lighting in the vehicle headliner. In its activated state, the transmitter module sends out sound waves at a frequency of 40 kHz (imperceptible to the human ear) and receives the echo a short time later via the receiver module. The evaluation electronics detects irregularities in the ultrasonic field and sends an “alarm“ signal to the central locking control unit. The anti-theft warning system LED indicates that the system is on standby.SSP207/69Electrical circuit+30Self-diagnosis Address word for self-diagnosis: 45 The interior monitoring sensor unit only has diagnostic capability when deactivated.J42924 G209Only one bi-directional communication line is used to activate and trigger the alarm.31 KSSP207/67G209 J429 PIN1 PIN2 PIN3 PIN4Ultrasonic sensor for ATWS Central locking control unit K-diagnosis line Positive supply 12 V Earth Sensor signal “Activate alarm/signal“For more detailed information regarding the anti-theft warning system/interior monitoring, please refer to SSP 185.67 ElectricsThe immobiliseris an electronic anti-theft protection device of the 3rd generation and will be gradually phased into the Audi TT. It prevents the vehicle from being operated by unauthorised persons by intervening in the engine control unit. The aim of the 3rd generation immobiliser is to incorporate the engine control unit actively into evaluation and monitoring processes. The 3rd generation immobiliser differs from the previous immobiliser in the following respects: – Variable code evaluation in the engine control unit and immobiliser control unit. The engine control unit has an equation which calculates the generated variable code in the same way as in the immobiliser control unit.WAfter teaching in the electronic module of the key transponder once, the immobiliser key is paired up with the immobiliser and cannot be used for any other immobiliser.SSP207/88The components of the immobiliser are as follows:90 50 130 °C 0 1/2 1/130 20 1040 50 60 70607080 100 120 P–1605040!AIR BAGABS140 180200The immobiliser control unit is integrated in the dash panel insert. The warning lamp in the dash panel insert The reading coil on the ignition lock The adapted ignition key The engine control unit3020220240 010– –260SSP207/90– –Always use the corresponding Workshop Manual when carrying out repairs.SSP207/8968 Functional description After turning on the ignition, the key transponder sends the fixed code to the immobiliser control unit. If this is identified as correct, a variable code is generated in the immobiliser control unit. This code is sent to the transponder. A secret arithmetic process is started in the transponder and in the control unit according to a set of equations. The result of the computing process is evaluated in the control unit. If the results tally, the vehicle key is acknowledged as correct. The engine control unit then sends a variable code to the immobiliser control unit. The engine control unit has a set of equations. It is also stored in the immobiliser control unit, according to which the variable code is converted into a secret code. The “Adapt immobiliser” function also saves in the control units the result of key interrogation, the immobiliser PIN, the immobiliser control unit ID as well as the VIN . If all these data match up with one another, vehicle start-up is enabled. Due to the fact that a new variable code is generated every time in this secret computing processes, this code is not decipherable. It is not possible to copy the vehicle key.Self-diagnosis The immobiliser has extensive self-diagnosis capability. Address word: 17 You can find further information on the selfdiagnosis in the Workshop Manual “Electrical System”. Emergency start function The emergency start function makes it possible to re-enable a vehicle which is stranded because the immobiliser has been disabled. The prerequisite for this is a knowledge of the secret number. You can find further information on the emergency start function in the Workshop Manual “Electrical System”.V.A.G - EIGENDIAGNOSE 17 - SchalttafeleinsatzHELP1 2 3 4 5 6 7 8 9 C 0 QHELPPRINTV.A.G 1551SSP207/9369 ElectricsImmobiliser IIIImmobiliser control unit Communication Transponder (key )90 50 130 °C 01/2 1/130 20 1040 50 60 70607080 100 120 P5040!AIR BAGABS140160W1802003020220240 010260Communication via single lines Power supply Fixed codeIgnitio