TECHNICAL DOCUMENTATION
SSP 217 The V8-5V Engine

This PDF is currently unavailable.
Read document text
217Service.The V8-5V EngineConstruction Features and FunctionsSelf-Study Programme 217For internal use onlyAUDI has been producing advanced 8-cylinder engines since 1988. Their capacity has increased from 3.6 l to 4.2 l. The V8 engine in combination with Aluminium Space Frame technology was the technical basis for Audi's breakthrough into the luxury class.SSP217_048Steps to enhance the value of the Audi A8 have included the redesign of the V8 engine. The new V8-5V engines are now also available for the Audi A6 model range.2ContentPage IntroductionTechnical data ....................................................................... 5Engine - MechanicsCrankgear .............................................................................. Engine mounting .................................................................. Engine lubrication ................................................................ Cooling circuit ....................................................................... Cylinder head Five-valve technology ............................................. Roller rocker ............................................................ Camshaft adjuster .................................................. Toothed-belt drive; cylinder-head seal ................. Cylinder-head cover seal ........................................ Exhaust manifold .................................................... 6 9 10 16 19 20 22 24 25 26Engine - Motronic SubsystemsVariable intake manifold ...................................................... 27 Secondary air system ........................................................... 32Engine ManagementSystem overview ................................................................... Function diagram ................................................................. Quick-start functions Camshaft position sensor ...................................... Engine run-down sensor ........................................ Electronic throttle function ................................................. CAN bus interfaces ............................................................... Additional signals / interfaces ............................................ 36 38 40 41 42 44 46Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49New! The self-study programme provides you with information concerning the engine's construction features and functions. The self-study programme is not a repair manual! When carrying out maintenance and repair work, it is essential to use the latest technical literature.Caution! Important!3IntroductionV8-5V EnginesSSP213_073Major modifications were made to the V8 engines during the course of further development. Emphasis was placed on the following development objectives: – compliance with future exhaust-emission regulations – reduction of fuel consumption – increase in torque and power – improvement of comfort and convenience – reduction of engine weight – increased use of shared components for the AUDI engine series. The following new features and modifications have been incorporated in the V8 4-valve engine.New features – Five-valve cylinder head with roller rocker – Camshaft adjustment – 3-stage variable intake manifold – Engine management system, Bosch ME 7.1 – Electro-hydraulic engine mounting Modifications – to crankcase and crankgear – to oil circuit – to cooling circuit4Technical data3.7 l Engine code AQG 4.2 l AQF (A8) ARS (A6)4003.7 l V8-5V engine200350175Design Capacity Power outputV8 engine with 90o V angle300 150250125191 kW 260 hp at 6000 rpm 51.6 kW/l 70.3 hp/l 350 Nm at 3200 rpm 94.7 Nm/l228/220 kW 310/300 hp at 6000 rpm 54.6 kW/l 74.3 hp/l 410 Nm at 3000 rpm 98.3 Nm/l2001001507510050Specif. output5025Torque000 1000 2000 3000 4000 5000 6000 7000Speed (rpm)SSP217_004Specif. torque Bore Stroke Compression ratio Weight Engine management Fuel Firing sequence Exhaust-emission standard4.2 l V8-5V engine500 450 250 225 200 175 150 125 100 75 50 25 0 1000 2000 3000 4000 5000 6000 700084.5 mm 82.4 mm 11:1 198 kg84.5 mm40093.0 mm 11:1 Torque (Nm) 200 kg350 300 250 200 150 100 50 0 0Motronic ME 7.198/95 RON 1-5-4-8-6-3-7-2Speed (rpm)SSP217_005EU 3The specified power data is only possible if 98 RON fuel is used. A reduction in power output must be expected if 95 RON fuel is used.Power output (kW)Power output (kW)3697 cm34172 cm3 Torque (Nm)5Engine - MechanicsCrankgearSSP217_054The crankcase has been adapted to the modifications made to the oil supply system and cooling circuit.Cracked-steel conrods have been used for the 3.7 l engine since 1995 and are now also being used for the 4.2 l engine. The conrods are shared components used in both the 2.4 l and 2.8 l engine.SSP217_0066SSP217_055Owing to the design of the valve recesses, the pistons are specifically intended for use in the appropriate cylinder bank only.SSP217_0027Engine - MechanicsWide, milled ventilation recesses above the thrust bearings reduce pumping losses. Bolts are also inserted at the side of the two front crankshaft bearing caps to improve running smoothness (see SSP 198, page 6).SSP217_007The locking mandrel (V.A.G 3242) used for the V6 engines is also used for locking the crankshaft. It is applied to the crank web of the 4th cylinder and is used for basic engine adjustment and also as a counterhold for loosening and tightening the central bolt of the crankshaft.The 5th cylinder must be set to ignition TDC.SSP217_0098MarkingThe central bolt does not have to be unscrewed for the vibration damper to be removed. The marking indicates the ignition TDC of the 5th cylinder.SSP217_050Central boltEngine mountingTo enhance driving comfort, hydraulic engine mounts with electrical activation are used for the 8-cylinder engines. They function in the way as described in SSP 183/16. The mounts are activated by the engine control unit according to engine speed and vehicle speed.SSP217_039 Electrical connection9Engine - MechanicsEngine lubricationTriple roller rockerOil-level sensorSSP217_010A duocentric oil pump driven by the crankshaft via a chain replaces the previously used external gear oil pump. The duocentric oil pump extends deep into the oil sump. The low suction height means that the oil pressure can build up quickly, especially with cold-starts. The oil-pressure control valve is located in the oil pump housing. The “diverted“ oil is led off to the intake side of the oil pump. This helps optimise the level of efficiency.In the intake spindle shafts, there are 5 oil bores per triple roller rocker. Three oil bores each supply one hydraulic tappet. Two oil bores supply the oil-spray bores integrated in the roller rocker to lubricate the rollers. The oil-spray bores are only opened when the roller rockers are actuated. This results in a reduction of the amount of oil required in the cylinder head.The roller rockers are described on pages 20 and 21.10Cylinder bank 1Cylinder bank 2BAAPThrottleA BB AOil retention valvesThrottle Spray jet valve CamshaftOil filter moduleOil pressure control valveFilter elementOil cooler Duocentric oil pumpOil sumpSSP217_011Bypass valvesSlight modifications have been made to the oil circuit in the cylinder heads. The oil circuit for cylinder bank 2 shown in the illustration is the oil circuit that has been used since the introduction of the new model. Cylinder bank 1 shows the modified oil circuit.Oil flow (pressurised) Oil flow (non-pressurised)11Engine - MechanicsOil filter module (A8)Oil cooler bypass valve Coolant supply Alternator mount (part of oil module) Coolant return Oil return Oil supply Oil pressure switchSSP217_013 Filter bypass valve Drain plugThe oil filter module contains the oil filter and oil cooler. It is also used to hold the alternator.As was previously the case, the oil cooler is designed as a coolant-to-oil heat exchanger. The “housing-less“ oil cooler is bolted to the oil filter module using an O-ring seal to form a single unit.12Oil filter module (A8)Coolant supply (from engine) Plastic connection Oil coolerCoolant returnOil duct Oil cooler bypass valveOil return (to engine)Oil supply (from engine) Oil cooler supplyEngine oil Oil cooler return O-ring seal SSP217_014 Coolant supply Sealing surface (Oil cooler) CoolantOil filter module (A6)Alternator holder Oil filter cartridgeFor space reasons, the A6 oil filter module is fitted with an oil filter cartridge.SSP217_00313Engine - MechanicsDuocentric oil pumpExternal runnerInternal gearOil pressure control valveThe pitch of the internal gear and the external runner has no functional significance and is determined by production engineering factors. To ensure that the assembly functions correctly, the narrow gears must not run together on the same plane.SSP217_012Oil level sensor The oil level sensor functions as an information sender which allows the flexible service interval to be calculated and the oil level to be displayed in the dash panel insert. Further information can be found in SSP 207 (from page 84 onwards) and SSP 213 (from page 55 onwards).SSP217_063 Oil level sensor 14Notes15Engine - MechanicsCooling circuit(Example: A8)Heat exchanger / valve unitCoolant temperature sender G2 and G62Coolant pipe (return for heater, oil cooler and expansion tank)Breather pipeReturn from oil coolerNew coolant pipe to cylinder head (small cooling circuit)Radiator fan thermo switch F18/F54 SSP217_015The flow direction of the coolant has been changed in the new V8 5-valve engines. As with the V6 engines, the coolant leaving the cylinder heads merges in the rear coolant pipe from where it is then led off to the cooler.16The new coolant pipe alters the coolant flow in the „small“ cooling circuit.New coolant pipe to cylinder head (small cooling circuit) Coolant pipe (return for heater, oil cooler and expansion tank)Oil cooler return Breather pipe (to expansion tank)SSP217_016 to vehicle radiator Coolant return Heat exchanger (A8) to expansion tank (A6) Coolant pipe (rear) Coolant temperature sender G2 and G62Coolant supply for heat exchangerTo expansion tank (A8) Coolant return Heat exchanger (A6)17Engine - MechanicsPrevious design: The coolant thermostat is connected to the “small coolant circuit“ via two holes in the cylinder crankcase (see Fig. 217_017). The holes are directly connected to the cylinder-head water jacket (1st cylinder) and the water jacket of the cylinder crankcase. The heated coolant flows from the 1st cylinder to the coolant thermostat.SSP217_018New design - modified components: – Cylinder head in bank 1 modified – Additional coolant pipe – Rear coolant pipe modifiedNew design New coolant pipe SSP217_019The connection in the cylinder head to the water jacket (cylinder crankcase) has been split (see Fig. 217_019). The coolant from the rear coolant pipe is forked by the new coolant pipe (mixture from all cylinders) and then passes through the cylinder head to the two holes which lead off to the coolant thermostat. This ensures uniform temperature control. The function of the cylinder head is to connect the coolant pipe to the two holes leading off to the coolant thermostat.From radiator Coolant thermostat SSP217_017 To coolant pump Coolant pipe (return for heater, oil cooler and expansion tank) 18Cylinder headFive-valve technologySSP217_020Five-valve technology is now also being used in the V8 engines. Roller rockers are being used for the first time in the enhanced five-valve cylinder head. This considerably reduces frictional losses in the valvegear which, in turn, significantly improves efficiency.The rockers are made of die-cast aluminium in order to keep inertia forces as low as possible. As a result, the valvegear is able to function reliably at engine speeds of up to 7200 rpm. The use of roller rockers has not only meant a considerable reduction in frictional losses in the valvegear, but has also halved the oil delivery rate in the cylinder heads. This also has a positive effect on the degree of efficiency.19Engine - MechanicsRoller rocker Exhaust valveSingle camTwin roller rockerSSP217_023 Roller located between rocker arms Spindle shaft, also used to supply oilOil spray hole Exhaust valve 20.2˚SSP217_022Every valve has a hydraulic valve lifter which is integrated in the rocker. The rockers are supported by a spindle shaft which is also used to supply oil to the bearings and the hydraulic valve lifters.The two exhaust valves are actuated by a twin roller rocker. The single cam actuates the rocker by means of a roller located between the rocker arms.The individual hydraulic valve lifters can be replaced without the rockers needing to be removed.20Inlet valveDouble camHydraulic valve lifter with slide pad (hydraulic valve tappet)Spindle shaftTriple roller rockerSSP217_025 Oil duct Inlet valve 2 14.9˚The three inlet valves are actuated via a triple roller rocker. A double cam actuates the rocker by means of two rollers between the rocker arms.Inlet valve 1 and 3 21.6o SSP217_024Tolerance compensation for inlet triple RR (roller rocker) To ensure uniform compression between the two cams and rollers of the roller rockers, the spindle shaft of the inlet roller rocker is convex in shape in order to compensate alignment and component tolerances. This prevents the roller rockers from “tilting“.Cams Camshaft axisCylinder headSpindle shaft axis (actual)For the sake of clarity, the tolerance of the spindle shaft relative to the camshaft has been greatly exaggerated in the illustration.Spindle shaft axis (target) RollersSSP217_02121Engine - MechanicsCamshaft adjuster (cylinder bank 1)Tensioning piston Chain tensioner slide pad Oil reservoir Hydraulic cylinder with switching pistonCamshaft adjustment valve N205 Adjuster piston Slide pad adjusterLocking pins for starting phaseSSP217_026The camshaft adjustment system, a feature incorporated in Audi's current range of engines, is also used in the new generation of V8-5V engines. When the engine is switched off, no oil pressure is applied to the chain tensioner and camshaft adjuster. Owing to the Ferraria effect in the chain drive when the engine is started, vibrations which generate noise occur until sufficient oil pressure has built up.In the case of the new V8 engines, an interlock function and an oil reservoir were added to the proven system during the course of further development. These new features prevent vibrations in the chain drive which has a positive effect on acoustic behaviour during the start phase.The principle of camshaft adjustment is described in SSP 182.22Lubrication and breather holeEngine off:Oil supplyIf there is no oil pressure, a spring-loaded locking pin is pushed into the detent slot of the adjusting piston. The adjusting piston is then locked.Locking pinOil returnAOil reservoirBAdjusting pistonBASSP217_027 Control ductsEngine start: The adjusting piston is locked until sufficient oil pressure has built up. This prevents vibrations in the chain drive and, therefore, noise generation.Retard setting (Basic and power setting)The camshaft adjuster is locked in the “Retard position“.ABEngine running: Once a defined oil pressure has been reached, it acts on the surface of the locking pin, i.e. against the resistance of the spring. The locking pin releases the adjusting piston so that the engine control unit can adjust the timing in the “Advance“ direction.BASSP217_028Advance setting (Torque setting)Oil reservoir The oil reservoir ensures that the pressure chamber of the tensioner piston is filled during the non-pressurised phase of the starting cycle. This also has a positive effect on acoustic behaviour when the engine is started. A hole in the top of the oil reservoir allows air to escape and supplies the chain with oil.B A23ABSSP217_029Engine - MechanicsToothed-belt drive The toothed-belt drive is identical to that of the V6-5V engine. The V8-5V engine is also fitted with a stabilising roller. The components are largely identical to those of the V6-5V engine.Stabilising rollerEccentric rollerSSP217_038Cylinder-head seal The new V8-5V engines have a multi-layer metallic cylinder-head seal already used in the 4 and 6-cylinder engines. This seal replaces the soft seal used in previous models. It consists of 3 individual metallic layers. The two outermost layers are treated with a special coating. Advantages: – Very good settling behaviour – Improved durabilityCoatingSSP217_056 24Cylinder-head cover sealSealDecoupling element (long) Spacer sleeve Cylinder head coverProfiled rubber grommetSeal cylinder head cover SSP217_040 Decoupling element (short) Spacer sleeveThe thin-wall cylinder head covers are made of a die-cast magnesium alloy. A seal concept, which decouples the cylinder head cover from the cylinder head, improves the acoustics of the engine. The bolted connections of the cylinder head cover have decoupling elements. A seal, which is similar to a radial shaft oil seal, is used for the spark-plug shaft.The above-mentioned measures means that the cylinder head cover is not directly coupled with the cylinder head. It is, therefore, “insulated“ against vibrations generated by the engine.The securing bolts must be tightened uniformly in the specified order to prevent distortion of the cylinder head cover and to ensure that the seal is completely air-tight. Always refer to the information given in the repair manual.126481012973511SSP217_043 25Engine - MechanicsExhaust manifoldManifold flange (left-hand cyl. bank)Connection for front exhaust pipe Outer shellIndividual pipes reshaped for internal high pressureCloverleaf arrangementSSP217_036The pipe sections and assembly of the airgap-insulated exhaust manifold have been modified. The exhaust pipes of the individual cylinders are assembled in a cloverleaf configuration for each cylinder bank (4 in 1 arrangement).This protects the individual cylinders effectively against annoying exhaust vibrations which, in turn, has a positive effect on engine-torque characteristics.26Engine - Motronic SubsystemsVariable intake manifoldIntake moduleIntake manifold flap, stage 3 Intake air (inlet)tle ot r h E-t tem s m y Fro lve s vaVacuum unit Intake manifold flap, stage 3Holders for injectorsIntake manifold flap, stage 2 (open)Vacuum unit Intake manifold flap, stage 2Resonance tube, cyl. 5 (inlet side)SSP217_031Increasing torque by means of variable intake manifolds is a tradition at Audi. A three-stage variable intake manifold made of a die-cast magnesium alloy, a further development of previous concepts, is to be used for the first time. The variable intake manifold consists of four principal housing components which are bonded and bolted together. The concept uses two intake manifold flaps to produce three different intake manifold lengths (“resonance tube lengths“). To utilise the pulsations to optimum effect, the intake manifold flaps close the resonance tube openings by means of a circumferential, moulded-on sealing lip.The variable intake manifold must not be dismantled. If necessary, the entire assembly must be completely replaced.SSP217_030 27Engine - Motronic SubsystemsStage 1 Lower speed rangeIntake manifold flap Stage 3 Intake manifold flap Stage 2When the engine is switched off, both flaps are open. If the engine is idling, the two vacuum units are evacuated by the appropriate intake manifold changeover solenoid valves. The intake manifold flaps are, therefore, closed between the idling speed and the switching speed.SSP217_032Stage 2 Middle speed rangeIn the middle speed range, the intake manifold changeover solenoid valve N156 allows atmospheric pressure into the vacuum unit of the stage 3 intake manifold flap. The stage 2 intake manifold flap is opened and the intake path is shortened.SSP217_033Stage 3 Upper speed rangeIn the upper speed range, the stage 3 intake manifold flap is also opened. The intake air takes the shortest path to the combustion chamber.SSP217_034 28Effect of variable intake manifold on torque500Torque400300200015003000 3360Speed4500 520060007500SSP217_035 Lower full throttle (stage 1) Middle full throttle (stage 2) Upper full throttle (stage 3)Since the maximum torque across the speed range depends primarily on the length and cross section of the intake manifold, the new three-stage variable intake manifold comes closest to producing the optimum characteristic torque curve across the speed range. Depending on the engine speed, appropriate “resonance tube lengths“ are available for the lower, middle and upper speed range.The illustration explains the correlation between the length/cross section of the intake manifold and engine speed and shows the characteristic torque curve produced by the 3 stages.29Engine - Motronic SubsystemsThe vacuum required to control the variable intake manifold and the secondary air system is provided by two vacuum reservoirs. If a vacuum exists in the intake manifold, the reservoirs are evacuated via a non-return valve.SSP217_051Fitting location of vacuum reservoir, Audi A8Fitting location of vacuum reservoir, Audi A630Vacuum unit, stage 3Secondary air inlet valve N112From vacuum reservoirNon-return valveSSP217_052Intake manifold changeover solenoid valve N261, stage 2From vacuum reservoirIntake manifold changeover solenoid valve N156, stage 2 Vacuum unit, stage 231Engine - Motronic SubsystemsSecondary air systemJ220N112AG108G70 G39G62B Energised Not energisedV101 J299SSP217_042Owing to the high mixture enrichment during the cold-start and warm-up phase, an increased proportion of unburnt hydrocarbons exists in the exhaust gas during this time. The catalytic converter cannot process this high proportion of hydrocarbons because: 1. the required operating temperature of the catalytic converter has not yet been reached and 2. a lambda 1 mixture must exist to allow complete conversion.Air injection downstream of the outlet valves causes oxygen enrichment of the exhaust gases. As a result, the hydrocarbons and the carbon monoxide undergo post-oxidation (afterburning). The thermal energy released during this process also heats up the catalytic converter so that it reaches its operating temperature more quickly. The secondary air system consists of – the secondary air pump V101 – two combination valves A + B – the secondary air inlet valve N11232Secondary air inlet valve N112SSP217_001 Combination valve Cylinder bank 2 Connection for fresh air from secondary air pump V101 Combination valve Cylinder bank 1 Vacuum from engineControl line (vacuum or atmospheric pressure from secondary air inlet valve N112)Fresh air from secondary air pump V10133Engine - Motronic SubsystemsSecondary air inlet valve N112 The secondary air inlet valve is an electropneumatic valve. It is activated by the Motronic control unit and controls the combination valve. It releases the vacuum stored in the reservoir to open the combination valve. Atmospheric pressure is released to close the combination valve.To vacuum reservoirEnergised Not energised Filter cap AtmosphereTo combination valvesCombination valve The combination valve is bolted to the secondary air duct of the cylinder head. The vacuum from the secondary air inlet valve causes the air channel between the secondary air pump and the secondary duct of the cylinder head to open. At the same time, the valve prevents hot exhaust gases from entering and then damaging the secondary air pump.SSP207_016Valve openValve closedVacuum in control line from secondary air inlet valve Fresh air from secondary air pump SSP207_019 To secondary air ductAtmospheric pressure in control line from secondary air inlet valveSSP207_018 Exhaust gas34Secondary air pump V101 The secondary air pump relay J299 activated by the Motronic control unit connects the power supply for the secondary air pump motor V101. The fresh air mixed with the exhaust gas is drawn from the air filter housing by the secondary air pump and released by the combination valve. The secondary air pump in the Audi A8 has its own air filter. The pump is integrated in the air filter housing where it draws in unfiltered air. The secondary air system is active at coolant temperatures between 0 and 55 ˚C. The secondary air pump relay J299 and the secondary air inlet valve N112 are activated simultaneously. The system is switched off after a defined air mass has been drawn in by the motor (information from the air mass meter). At idling speed, this occurs after approx. 60 - 90 seconds.To combination valveAir filter boxSSP217_049 Secondary air pump, Audi A8The secondary air system is described in SSP 207.Air filter boxThe secondary air pump in the Audi A6 does not have its own air filter. It is mounted to the longitudinal member and draws the filtered air from the air filter box.To combination valve Clean air intakeSecondary air pump Audi A6SSP217_057 35Engine ManagementSystem overviewMotronic ME 7.1 SensorsHot-film air mass meter G70 Motronic control unit J220 Altitude sender F96 (integrated in control unit)Engine speed sender G28Hall sender G40 (bank 2) and Hall sender 2 G163 (bank 1)Lambda probe G39 (bank 1) and lambda probe G108 (bank 2)Throttle valve control unit J338 with throttle valve drive G186 (electric throttle operation) Angle sender -1- for throttle valve drive G187 Angle sender -2- for throttle valve drive G188Coolant temperature sender G2 and G62 Steering angle sender G85 Knock sensor 1 G61 (bank 1) and knock sensor 2 G66 (bank 2)Control unit for ABS with EDL J104 Pedal sender/accelerator pedal module with accelerator pedal position sender (1) G79 and accelerator pedal position sender (2) G185 Automatic gearbox control unit J217 Brake light switch F and brake pedal switch F47 Clutch pedal switch F3 (with manual gearbox only) Additional signals – Air conditioner requirement signal – Air conditioner compressor, bidirectional – Crash signal – CCS switch 36 * No CAN businterface with Audi A6 * Combination processor in dash panel insert J218* Air conditioner/Climatronic operating and display unit E87Active componentsFuel pump relay J17 and fuel pump G6Injectors N30, N31, N32, N33 (bank 1) Injectors N83, N84, N85, N86 (bank 2)Ignition coil N (1st cyl.), N128 (2nd cyl.), N158 (3rd cyl.), N163 (4th cyl.)Ignition coil N164 (5th cyl.), N189 (6th cyl.), N190 (7th cyl.), N191 (8th cyl.)Activated charcoal filter system solenoid valve N80 Secondary air pump relay J299 and secondary air pump motor V101 Diagnosis Secondary air inlet valve N112 Throttle valve control unit J338 with throttle valve drive G186Camshaft adjustment valve N205 (bank 1) and N208 (bank 2) Intake manifold changeover valve N156 Intake manifold changeover valve 2 N261 Lambda probe heating Z19 (bank 1) and lambda probe heating Z28 (bank 2) Additional signals – Air conditioner compressor (out) SSP217_046 Engine mount 1 and 2 37Engine ManagementFunction diagram4.2/3.7 l in A8 GPColour coding = Input signal = Output signal Components A E45 D F F36* F47 G2 G3 G6 G28 G39 G40 G61 G62 G66 G70 G79 G108 G163 G185 G186 G187 G188 J17 J220 J299 M9 M10 N N30 N31 N32 N33 N80 N83 N84 N85 N86 N112 N128 38 Battery Cruise control system switch Ignition/starter switch Brake light switch Clutch pedal switch (with manual gearbox only) Brake pedal switch for cruise control system Coolant temperature sender Coolant temperature gauge Fuel pump Engine speed sender Lambda probe Hall sender Knock sensor 1 Coolant temperature sender Knock sensor 2 Air mass meter Accelerator position sender Lambda probe 2 Hall sender 2 Accelerator position sender 2 Throttle valve drive (electric throttle operation) Angle sender 1 for throttle valve drive Angle sender 2 for throttle valve drive Fuel pump relay Motronic control unit Secondary air pump relay Brake light bulb (left) Brake light bulb (right) Ignition coil (cylinder 1) Injector (cylinder 1) Injector (cylinder 2) Injector (cylinder 3) Injector (cylinder 4) Activated charcoal filter system solenoid valve Injector (cylinder 5) Injector (cylinder 6) Injector (cylinder 7) Injector (cylinder 8) Secondary air inlet valve Ignition coil 2 N144 N145 N156 N158 N163 N164 N189 N190 N191 N205 N208 N261 P Q S ST V101 Z19 Z28 S204 Solenoid valve (left) for electro/hydraulic engine mounting Solenoid valve (right) for electro/hydraulic engine mounting Intake manifold changeover valve Ignition coil 3 Ignition coil 4 Ignition coil 5 Ignition coil 6 Ignition coil 7 Ignition coil 8 Camshaft adjustment valve 1 Camshaft adjustment valve 2 Intake manifold changeover valve 2 Spark plug connector Spark plugs Fuse Fuse holder Secondary air pump motor Lambda probe heating Lambda probe heating 2 Fitting location in Audi A6: plenum chamber next to battery Fitting location in Audi A8: top right in luggage compartment = Positive = Earth = BidirectionalAdditional signals and connections K diagnosis connection 1 2 3 Crash signal (in) from airbag control unit Air conditioner requirement signal (in) Air conditioner compressor signal (in-out) } } } } } Connection to data busCAN-BUS L CAN-BUS H X Y ZConnections in function diagram30 15 X30 15 XJ17 4X 30 D 15XS204S1S2S3ST4S116S117S130S ST3 S6ST4 S10ST2 S9 CAN - BUS L CAN - BUS HZY E45 J299 N156 N261 N112 N205 N208 N80 N145 N144 M9M* F36F47F123N30N31N32N33N83N84N85N86 V101M10 + 31AJ220Y-+Z-+-+--+G3NMN128N158N163N164N189N190N191λ λM++mlG6G70G39 Z19G108 Z28G79G185G188 G187G186G163G40G28G66G61G2G62P QP QP QP QP QP QP QP Q3131SSP217_044Engine ManagementQuick-start functionsCamshaft position sensor G40 and G163 As with the V6-5V engines, the new V8-5V engines also have two sensors for determining the position of the camshaft (G40 and G163). The sender system with “quick-start rotor ring“ already used in the 4- cylinder 5-valve engines is implemented. The quick-start rotor ring has two wide and two narrow stops (two small and two large windows). If a stop is in the Hall sensor, the level at the signal output sensor is high.SSP217_053Signal trace for engine speed sender G28 and Hall sender G40 using oscilloscope function of VAS 50515 V/Div. 10 ms/DivAutomatic modeG40G28SSP217_062 Sender wheel* Software reference mark By using different stop widths, it is possible to use the signal from G40 together with the engine speed sender G28 to determine the camshaft position relative to the crankshaft more quickly.66o before TDC of 1st cylinderTDC of 1st cylinderWhen the engine is started, the engine control unit can thus determine the ignition TDC of the next cylinder more quickly so that the engine starts more quickly (synchronisation with the 1st cylinder is no longer necessary). This is referred to as quick-start synchronisation or the quick-start function.40* The software reference mark is the point from which the control unit commences its calculations to determine the ignition point. It is about one tooth after the hardware reference mark, which is approximately 66˚ - 67˚ cr./shaft before ignition TDC of the 1st cylinder.Signal trace of engine speed sender G28, and Hall sender G40 and G16310 V/Div. 20 ms/DivAutomatic modeG163 G405 V/Div. 1 5 420 ms/Div 8 6 3 7 2G28TSSP217_061The camshaft position sensor G163 is used to monitor camshaft adjustment and to generate a substitute signal if the G40 fails.The camshaft position sensor G40 is mounted to cylinder bank 2. The camshaft position sensor G163 is mounted to cylinder bank 1.Engine run-down sensor The ME 7.1 engine management system has an engine run-down sensor. This device supports the quick-start function so that fuel injection can occur before quick-start synchronisation. The engine control unit remains active for a defined time after the ignition has been switched off and, with the aid of the G28, “monitors“ the engine as it slows to a standstill. The position of the engine mechanics (position of the next cylinder at ignition TDC) is stored and is available the next time the engine is started. The ME 7.1 can immediately begin injection and has a fuel mixture ready, which has a positive effect on starting behaviour.41Engine ManagementThe ME 7.1 engine management system has to a large extent been described in SSP 198. The new functions and features of the system used in the V8-5V engine are dealt with below.Electronic throttle functionApart the following features, the electronic throttle functions are identical to those described in SSP 198. The pedal sender is used in the Audi A8 and the accelerator pedal module in the Audi A6 to determine the requirements of the driver.Accelerator pedal Kickdown switchPedal sender (Audi A8) A separate switch is used to provide kickdown information. It is located in the footwell and doubles as the accelerator pedal stop. The full-throttle and kickdown positions must be calibrated accordingly.SSP217_04142Accelerator pedal module (Audi A6) No separate switch is used to provide kickdown information. In the case of automaticgearbox vehicles, the accelerator pedal stop is replaced by a pressure element. The pressure element generates a “mechanical pressure point“ which gives the driver the “kickdown feeling“. If the driver activates the kickdown, the fullthrottle voltage of the accelerator pedal position senders is exceeded. If a voltage defined in the engine control unit is reached, this is interpreted as a kickdown and the information is sent to the automatic gearbox via the CAN bus. The kickdown switching point can only be tested using diagnostic testers.Kickdown range Accelerator pedal travel5,0 G79Signal voltage (V)G1850 20 % 40 % 60 % 80 % 100 %Driver torque range SSP217_060Full-throttle stop (mechanical) Accelerator pedal final stopIf the accelerator pedal module or the engine control unit is changed, the switching point of the kickdown switch must be reprogrammed using the diagnostic tester – see the repair manual.43Engine ManagementCAN bus interfacesGearbox control unit Adaptation release Idle charge compensation Switch off compressor Idling speed, target speed Engine torque (TARGET) Emergency running programmes (info via self-diagnosis) Gear change active / inactive Selector lever position Torque converter/gearbox guard Torque converter clutch status Current gear and target gear ESP control unit ASR request ASR intervention torque (TARGET) Brake pedal status ESP intervention Road speed MSR request MSR intervention torqueEngine control unit Intake air temperature Brake light switch Brake pedal switch Throttle valve angle Electronic throttle warning lamp info Driver torque range Emergency running programmes (info via self-diagnosis) Accelerator pedal position CCS switch positions CCS target speed Altitude information Kickdown information Switch off compressor Compressor ON/OFF (check-back signal from bidirectional interface) Fuel consumption Coolant temperature Clutch pedal switch Idle detection Engine speed Engine torque (ACTUAL) ImmobiliserCAN-lowCAN-highDash panel insert Self-diagnosis info Road speed Mileage Coolant temperature Oil temperature ImmobiliserSteering angle sensor Steering wheel angle (used for precontrol of the idling speed control device and for calculating engine torque based on the power requirements of the power steering system)44In the Audi A8, data between the engine control unit and the other control units is, with the exception of a few interfaces, exchanged via the CAN system. The system overview shows the information which is provided by the engine control unit via the CAN bus, and received and used by the connected control units. The following two examples simplify the complexity of the CAN bus network. Detailed information concerning the CAN data bus can be found in SSP 186.Selector lever lock:Engine control unit J220Brake light switch F/F47Gearbox control unit J217Selector lever lock solenoid N110Kickdown (for example, Audi A6):Engine control unit J220Accelerator pedal module G79/G185 Gearbox control unit J217Information which is sent by the engine control unit.Information which is received and evaluated by the engine control unit.45Engine ManagementAdditional signals/ interfacesIn the Audi A8, the following interfaces also exist for data exchange via CAN bus: In the A6, there will be no CAN data exchange with the dash panel insert when production of the model begins. For this reason, the A6 has the following interfaces in addition to those of the A8:Pin 67 Pin 43 Pin 41 Pin 40Crash signal K-line/diagnostic connection Compressor ON/OFF Air conditioner requirement signalPin 43 Pin 19 Pin 81 Pin 54 Pin 37 Pin 48Immobiliser/self-diagnosis Coolant temperature signal Fuel consumption signal Road speed signal Engine speed signal Warning lamp for electronic throttleMost of the interfaces and additional signals of the ME 7.1 are described in SSP 198. Only the new interfaces and additional signals are dealt with below.46Crash signalSignal traces for crash signal using oscilloscope function of VAS 50515 V/Div. 0,1 s/Div.Automatic modeTStandard signal Crash triggeringSSP217_058In the event of a crash where the belt tensioners/airbags are triggered, the engine control unit deactivates actuation of the fuel pump relay. This prevents excessive quantities of fuel escaping if the fuel system is damaged. The crash signal is a square-wave signal with a specific signal ratio (high level to low level). The signal is transmitted continuously by the airbag control unit.In the event of a crash, the signal ratio is inverted for a defined period of time. During this period, the signal ratio is inverted relative to the standard signal so that the supply of fuel is shut off until the engine is restarted. In addition, the “crash shut-off“ fault is stored. The fault entry can only be deleted using the diagnostic tester.Triggering range5 V/Div. 0,5 s/Div.Recorder modeCrash signal with triggeringSSP217_059 47Engine ManagementSelf-diagnosis The crash signal is checked with respect to the plausibility of the crash signal and voltage. Effect of fault If the “crash shut-off“ fault is stored in the engine control unit and is not erased, the fuel pump is not primed with fuel when the ignition is switched on (no precompression is generated in the fuel system). This may result in delayed starting of the engine. The fuel shut-off system will not be incorporated in the Audi A6 and A8 until model year 2000.Further information concerning the fuel shut-off system can be found under Vehicle Safety in SSP 207 and SSP 213.The air conditioner requirement interface In the case of a high air conditioner output requirement, the idling speed of the engine is increased to increase the output of cool air from the air conditioner compressor. In some cases, air conditioning requirements may be such that the “air conditioner requirement“ interface is also switched to “high“ at the air conditioner operating and display unit whereupon the engine control unit is informed of the increased output requirement. This can be tested using the “Read measured value block“ function of the diagnosis tester (see repair manual). It is important to note that the function for increasing the idling speed is not available for all engine variants, even if the signal is sent to the engine control unit. Self-diagnosis The air conditioner requirement interface is not monitored by the self-diagnosis system. Effect of fault The idling speed is not increased which results in a reduction in the output of cool air when the engine is idling.48ServiceA number of new special tools are required by the Service department for repairing the V8-5V engine.Thrust pad for crankshaft oil seal Order No.T40007SSP213_007Tensioning roller spanner Order No.T40009SSP213_008Camshaft retainer Order No.T40005SSP213_00949Notes50Dear Reader,This self-study programme has allowed you to familiarise yourself with the new technical features of the V8-5V engine. Our aim is to make the content of the self-study programme material as interesting as possible. This is why we want to give you the opportunity to tell us your opinions and suggestions for future self-study programmes. The following questionnaire is intended to assist you in doing this. Send your comments and suggestions to the fax number 0049/841 89 36 36 7.We thank you for your support. The Technical Training Service Team51All rights reserved. Subject to technical modifications. AUDI AG Abteilung I/VK-5 D-85045 Ingolstadt Fax 0841/89-36367 940.2810.36.20 Technical status 02/99 Printed in Germany217