TECHNICAL DOCUMENTATION
SSP 232 5 speed Automatic Gearbox

This PDF is currently unavailable.
Read document text
Service.Self-Study Programme 2325-speed Automatic Gearbox 09A/09BDesign and FunctionThe new 5-speed automatic gearboxThe new automatic gearbox is intended for installation in the Volkswagen and Audi platform for transversely mounted engines.232_020232_999232_998NEWImportant NoteThe Self-Study Programme describes the design and the function of new developments! The contents are not updated!Please always refer to the relevant Service Literature for all inspection, adjustment and repair instructions.Literature.2Table of ContentsGeneral information . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Basic configuration of gearbox . . . . . . . . . . . . . . . . . . 8Selector mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . 26Torque curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Electronic components - Control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 - Output signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 - Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 - Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Function diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Self-diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . 683General informationAs with the 4-speed automatic gearbox in the Polo and Lupo, the new 5-speed automatic gearbox is built by Jatco, the well-known automatic gearbox manufacturer. The gearbox was adapted to the vehicle and the control unit software in co-operation with Volkswagen's engineers.232_021This gearbox is notable for the following components and functions: - Automatic shifting of the five gears bydriver and situation dependent driving programs (fuzzy logic: see SSP No.172) - A drag-dependent driving program (recognises traction resistances when driving uphill and downhill, when towing a trailer and when driving into a headwind) - Tiptronic - Shift indicator in dash panel insert - Ignition key removal lock - Torque converter with torque converter lock-up clutch - Stationary decoupling When the vehicle stops and a forward drive position is engaged, the gearbox changes into neutral. Advantage: the vehicle shows no tendency to creep, which means higher fuel economy and lower emissions.4SpecificationsDesignation Max. torque Weight A-platform 09A/09B Sharan 350 Nm unladen filled with ATF oil G 052 990 9l 5l 7 l when changing the converter 89.5 kg 101.5 kgATF oil Capacity Oil-change quantityThe ATF oil is designed to last for the service life of the gearbox. It also lubricates the final drive.232_9975General informationThe selector leverhas two selector gates: one for automatic gearshifts and one for Tiptronic.232_010232_221Automatic selector gate In »D« position, the gearbox automatically changes gears 1 to 5 depending on load. However, first gear cannot be selected directly by the driver - it is engaged by the control unit depending on vehicle load. 1st gear can only be engaged directly in the Tiptronic selector gate. In this case, 1st gear uses the engine brake.Tiptronic selector gate If the selector lever is engaged in the right selector gate, the gearbox is in the Tiptronic program. If the selector lever is moved forward or backward in this program, the gearbox shifts up or down a gear. Move selector lever towards "+", to select the next higher gear. Move selector lever towards "–", to select the next lower gear. The gear selected is displayed in the dash panel insert.6Selector lever mechanism232_095Selector lever lock solenoid N110 232_096 232_094The selector lever lock is implemented as described previously by means of the selector lever lock solenoid. The selector lever lock prevents accidental selection of a drive position while the engine is running. The solenoid does not cancel the interlock until the brake is operated.The ignition key removal lock only allows the ignition key to be withdrawn in selector lever position »P«. This stops the driver exiting the vehicle without applying the parking lock.Starting the engine The engine can only be started in »P« or »N« position.Push-starting and towing The conditions for push-starting or towing have not changed compared with other Group automatic gearboxes. For more information, refer to the vehicle Owner's Manual.7Basic configuration of gearboxExternal viewsSelector lever232_010232_081Valve body cover and the valve body beneathFinal driveAutomatic gearbox control unitAutomatic gearbox232_021The automatic gearbox system can be subdivided into the following main components:The selector lever - signals to the control unit in the Tiptronic selector range the gear the driver wishes to select and - positions the manual selector valve in the valve body in the desired selector range in the automatic gearbox. The control unit - is the brain of the automatic gearbox. It controls all electrical and hydraulic functions of the automatic gearbox.The automatic gearbox - This translates all hydraulic and electrical control commands into mechanical functions or gears.8Several components of the automatic gearbox are recognisable from the exterior. In the following we will show you the complex inner workings of the gearbox in the form of a simplified cut-away diagram so that you can see how the individual modules and components are arranged inside the gearbox.Final drivePlanetary gearATF oil filler opening232_018 232_019Valve body cover and the valve body beneathIn this SSP we use schematic diagrams to explain the functional principle of the gearbox. These diagrams need not necessarily show the true installation position or dimensions.9Basic configuration of gearboxThe torque curveTo develop a 5-speed automatic gearbox for vehicles with transversely mounted engines it was necessary to arrange the three planetary gears on two planes due to the confined space. Planetary gears I and II are located directly on the turbine shaft. Planetary gear III is arranged below them on a separate shaft. Planetary gears I and II are coupled to planetary gear III via spur gears A and B. Torque is always output via the output gear on the shaft of planetary gear III. The torque is then transmitted from the output gear to the drive shaft via the differential. The ATF oil pump is driven by the input rotor of the torque converter.Spur gear A Spur gear BOutput gearDifferential232_01110Spur gear A Planetary gear I Planetary gear II ATF oil pumpTorque input Turbine shaftSpur gear B Output gearPlanetary gear IIIDifferential232_06711Gearbox designThe torque converteris equipped with a torque converter lock-up clutch which transmits the engine torque directly to the gearbox input shaft at high engine speeds. The control unit controls the closing movement of the torque converter lock-up clutch.Torque-converter housingFriction lining of torque converter lock-up clutchInput rotor Turbine rotorGearbox sideEngine sideGearbox housing 232_06812This is how it works: If the gearbox control unit decides, based on engine speed and engine torque, that it would be more economical to close the torque converter lock-up clutch, it activates solenoid valve N91. The oil chamber upstream of the torque converter lock-up clutch is opened by the solenoid valve to allow oil pressure to drop. This causes the oil pressure downstream of the clutch to increase. The clutch closes.232_070Torque converter lock-up clutch closedN91Oil inflow via the rear end of the lock-up clutchControl unitWhen solenoid valve N91 shuts off the flow, the oil pressure upstream of the clutch builds up again. The clutch opens.232_069Torque converter lock-up clutch openN91 ValveOil inflow via the front end of the lock-up clutchControl unitThe ATF oil pumpIt is driven by the input rotor of the torque converter. Its tasks are to draw ATF oil out of the oil sump, build up oil pressure and transfer oil pressure to the valve body.232_071Outer rotorInner rotorDrivePressure sideSuction side13Basic configuration of gearboxThe planetary gearIt comprises three individual planetary gears which engage the five forward gears and reverse gear.232_140 Sun gear II Turbine shaftPlanet carrierK3 Spur gear APlanetary gear I232_125Planetary gear II232_124Planetary gears I and II They are connected to the turbine shaft of the torque converter. Torque is applied to planetary gear I via clutch K3 (indirect connection). Torque can only be transmitted to planetary gear I when clutch K3 is closed. Planetary gear II is positively (directly) connected to the turbine shaft via the sun gear. Torque is always output from the planet carrier of planetary gear II to spur gear A.14Spur gear B Ring gear Planet carrier Output gear232_141to differential 232_128Planetary gear III It receives torque via spur gears A and B onto the ring. The torque is output via the planet carrier to the differential output gear.15Basic configuration of gearboxThe position of the clutches and brakesK3 K2 B2 K1 B1 FreewheelFreewheelK4 B3In this illustration the clutches and brakes are highlighted in colour to give you an overview of how they are arranged in the automatic gearbox.232_06016Gears are engaged by driving or arresting components of the planetary gear by opening and closing the clutches and brakes. Gears 1-4 and reverse gear are engaged via clutches K1, K2 and K3 and brakes B1 and B2.Drive-away engine torque is compensated by the freewheels on planetary gears I and III. 5th gear is engaged by clutch K4 on planetary gear III. Brake B3 is closed in all gears, except 5th gear.To give up a better idea of the interaction between mechanical and hydraulic components, we will explain the main components in simplified terms in the following chapters. For reference purposes, compare this figure with the cut-away diagram opposite.Planetary gear I Planetary gear IIFreewheel B2B1Spur gear AK1K2 K3DriveSpur gear BFreewheelK4 B3Planetary gear IIIto Differential232_06117Basic configuration of gearboxFixed connections Planetary gears I and II are mechanically coupled by the ring gear of planetary gear I and the planet carrier of planetary gear II. Torque is also output to spur gear A via planet carrier II.Ring gear I Planet carrier II Spur gear A232_153There are also positive mechanical connections in planetary gear III. Spur gear B is positively connected to the ring gear of the planetary gear and the planet carrier, in turn, is connected to the output shaft.Spur gear B Output shaft232_154 Ring gear III Planet carrier IIIThe clutchesThey are controlled by the valve body by applying ATF oil pressure. When closed, the clutches drive individual components of the planetary gear and this transfers engine torque to the final drive.232_21318Clutch K1 It drives the ring gear of planetary gear II and the planet carrier of planetary gear I when closed. Clutch K1 is closed in first, second and third gear and has a centrifugal force equaliser (for function see SSP172).232_106 232_100 K1Planet carrier IRing gear II 232_145Clutch K2 It drives the sun gear of planetary gear I. It is actuated by a ball valve and is closed in second gear (see SSP172).232_101232_126Sun gear I232_213K2232_14619Basic configuration of gearboxClutch K3 It drives the planet carrier of planet gear I. Third, fourth and fifth gear are engaged via K3. This clutch also has a centrifugal force equaliser.232_101232_102K3 232_147 Planet carrier IClutch K4 It drives the sun gear of planetary gear III in fifth gear. This clutch is also actuated by a ball valve.232_216232_217K4232_148 Sun gear III20The brakesThe brakes in the automatic gearbox have the task of controlling the gear ratios by arresting individual components of the planetary gear. Different types of brake are used in the 5-speed automatic gearbox: - Two multi-disc brakes and - a singleband brake.232_006Multi-disc brakes They function according to the same principle as plate clutches. They also consist of two clutch plate sets which are pressed together hydraulically. Unlike the clutches, which drive the movable components of the planetary gear, the multi-disc brakes arrest these components.232_007Example of multi-disc brake B1 Brake B1 is a clutch plate set connected to the gearbox housing and the planet carrier of planetary gear I. If the brake is required to arrest the planet carrier, the control unit sweeps the clutch plate set with ATF oil via the valve body.Band brakes They have the same function in the automatic gearbox as multi-disc brakes. However, the clutch plate sets are not pressed against each other. Instead, a brake band is tautened by a hydraulic cylinder. In this illustration you can see that the sun wheel of the planetary gear is arrested when the brake band is applied.232_06321Basic configuration of gearboxMulti-disc brake B1 It arrests the planet carrier of planetary gear II in reverse gear and the first gear of the Tiptronic by means of the engine brake.232_112B1Planet carrier II232_151Multi-disc brake B2 It arrests the sun gear of planetary gear I in second, fourth and fifth gear.232_105Sun gear IB2232_14922Band brake B3 It arrests the sun gear of planetary gear III. It is closed in all gears, except in fifth gear.232_107Sun gear IIIB3232_15023Basic configuration of gearboxThe pressure accumulatorA pressure accumulator is located in the hydraulic circuits of clutches K1, K3 and K4 as well as multi-disc brake B2. Two additional pressure accumulators are located in the valve body and gearbox housing respectively. Their task is to ensure that the clutches and brake mentioned above close softly.Pressure accumulator in the gearbox housing for clutch K4232_130Pressure accumulators in the housing and housing cover for brake B2232_129K1 K3Pressure accumulator on the valve body 232_131 for clutches K1 and K324This is how it works. Example: First gear, selector lever position "D". If one of the clutches or brakes mentioned in the introduction to this topic is closed, then pressurised ATF oil flows simultaneously from the valve body to the pressure accumulator and the clutch or brake to be closed.Controlled oil pressure Pressure accumulator with piston and piston springClutch232_001 Controlled oil pressure The maximum oilIn the pressure accumulator, the oil presses against a chamber filled with oil under pressure and a spring-loaded piston. A portion of the oil pressure is used to counteract the spring and oil pressure. Therefore, the full oil pressure is not applied to the clutch. The clutch does not close completely yet.pressure is not reached as the volume is expanding.232_002 Controlled oil pressure When the pistonOnly when the piston has reached its limit position does the full pressure act upon the clutch to close it completely. This process follows exactly the same pattern as clutches K3 and K4 and brake B2, and is repeated during every gearshift.has reached its limit position, the volume can expand no further. The maximum pressure is reached and the clutch closes.232_00325Selector mechanismThe hydraulic control unithas the task of controlling the automatic upshifts and downshifts of the individual gears at the correct point in time. It comprises the following component parts: - the valve body with control valve and two pressure accumulators, - the solenoid valves and - the hand-operated change-over valve.The valve body It has the task of adapting the oil pressure built up by the ATF pump to the shift pressure and distributing it to all gear shifting elements.232_116Solenoid valves N88- N93 and N281-N283 are arranged in the valve body. They are activated by the control unit. They are responsible for all changes in oil pressure in the oil galleries and supply the clutches and brakes with oil pressure.232_066The hand-operated change-over valve It is actuated by the selector lever. The driver defines the desired drive position with the selector lever. Fourth gear and reverse gear are engaged directly via this valve without intervention by the control unit.232_117232_12726Selector mechanismTo illustrate more clearly how the clutches and brakes on the planetary gear interact, we will now examine more closely what components are required to change gears. Let's recap on the component parts involved:B2 K2 K3Roller freewheelB1 K1Spur gear A Spur gear BOutput gear Sprag clutch232_061B3K4 Differential27Torque curve1st gear – selector lever position DRoller freewheel locked K1Sun gear IISprag clutch lockedB3 Torque input Torque curve Torque output Arrested components N88 N89232_156N92Valve bodySolenoid valves energisedIn Tiptronic 1st gear, brake B1 is additionally closed. So the vehicle can be driven with the engine brake.232_075282nd gearB2 K1Sprag clutch lockedB3 Torque input Torque curve Torque output Arrested components N88 N89232_157Valve bodySolenoid valves energised232_07629Torque curve3rd gearK3K1Sprag clutch lockedB3232_158Torque input Torque curve Torque output Arrested components N89Valve bodySolenoid valves energised232_077304th gearB2 K3Sprag clutch lockedB3232_159Torque input Torque curve Torque output Arrested components N92Valve bodySolenoid valves energisedIf the solenoid valves cannot be activated (e.g. because the control unit has failed), fourth gear is engaged by the manual selector valve.232_07831Torque curve5th gearB2 K3K4232_160Torque input Torque curve Torque output Arrested components N88 N92Valve bodySolenoid valves energised232_07932Reverse gearK2B1B3232_161Torque input Torque curve Torque output Arrested components N88 N89 N92Valve bodySolenoid valves energised232_08033System overviewSensorsAutomatic gearbox control unit J217Gearbox input speed sender G182Road speed sender G68Intermediate shaft speed sender G265Multi-function switch F125Tiptronic switch F189Gearbox oil (ATF) temperature sender G93Brake pressure switch F27034Signal for cruise control systemEngine control unit CAN busActuatorsSelector lever lock solenoid N110Ignition control signal to engine control unitSolenoid valves in the valve body N88, N89, N90, N92, N281Engine torque, engine speed Solenoid valves in the valve body N91, N93, N282Starter inhibitor relay J226Selector lever display illumination L101 Selector lever position P/N warning lamp K142from the ABS control unit to the air conditioning system control unit (if fitted)Road speed signal to control unit with display unit in dash panel insert J285232_01535Electronic components - The control unitAutomatic gearbox control unit J217This is the brain of the gearbox. It controls the output signals as well as the actuators, based on the information received from the sensors. The driving programs The control unit has a driver/situation-dependent driving program based on the information processing fuzzy logic (refer to SSP172). An additional program recognises and makes allowance for tractive resistance, e.g. when driving uphill or downhill, as well as the influencing factors when driving into headwind or towing a trailer. Emergency running mode If the gearbox control unit fails, - fourth gear and - reverse can still be selected. These gears are mechanically shifted in the valve body by the selector lever via the manual selector valve.232_081232_16236Torque signal from engine control unitIn all vehicles with an electronic accelerator pedal control (EPC), the main input variable in the gearbox control unit is the torque signal from the engine control unit. The gearbox control unit receives this signal via the CAN bus. It replaces the signal from the throttle valve potentiometer used in previous automatic gearboxes. Due to the new functional structure the engine control units, where engine torque is used as the central reference variable, the signal from the engine control unit now refers directly to the actual torque. This allows the gearbox control unit to adapt the shift pressures to the actual engine torque with much greater accuracy and to execute gearshifts more precisely and smoothly.Automatic gearbox Control unit Engine control unitEngine speed, load signal, ignition advance angle 232_173Signal utilisation On the basis of the torque signal, the gearbox control unit determines what shift pressures are required. The gearshift sequence is structured in such a way that the gearbox control unit first sends a signal to the engine control unit indicating that it wishes to execute a gearshift. The engine control unit then reduces engine torque so as to allow the gearbox control unit to close the clutches at low pressure. This results in soft, jolt-free gearshifts.Effects of signal failure Gearshifts are harsher as shift pressure cannot be adapted by the gearbox control unit.Electrical circuitCAN high CAN lowThis modification will also be made to the Polo with electronic accelerator pedal control and automatic gearbox.J217232_16437Electronic components - The sensorsData is transferred directly to the control unit (and not via the CAN bus)The engine speed sensorThere are three engine speed sensors in the automatic gearbox. All three sensors are housed in the gearbox and are not accessible from outside. They are all inductive senders and are of identical design.Gearbox input speed sender G182detects the speed of the gearbox input shaft by sampling the teeth on the outside of clutch K2.232_116232_212 232_209Signal utilisationThe control unit uses this signal to: - control the torque converter lock-up clutch and - calculate the slippage of the torque converter lock-up clutchEffects of signal failureThe gearshifts are harsher. The stationary decoupling function is de-activated and the lock-up clutch can no longer be closed.38Intermediate shaft speed sender G265232_116This sender picks up a signal corresponding to the number of teeth on spur gear A at the torque output of planetary gears I and II.232_208 232_210Signal utilisationThe control unit requires this signal to determine the opening and closing times of the clutches.Effects of signal failureThe stationary decoupling function is de-activated. The gearshifts are harsher.39Electronic components - The sensorsRoad speed sender G68232_116detects the speed of the parking lock gear.232_207 232_211Signal utilisationThe control unit requires this signal: - to calculate vehicle speed, - to select the gears and - to control the torque converter lock-up clutchEffects of signal failure5th gear is no longer engaged. The gearshifts are harsh, the stationary decoupling function is de-activated and the shift points are displaced.Electrical circuitJ217232_180G68G182G265The vehicle speed signal is sent to the control unit with a display unit in the dash panel.40Gearbox oil (ATF) temperature sender G93It is also located inside the gearbox housing. It continuously monitors the temperature of the ATF oil and sends a temperature signal to the gearbox control unit.232_208232_174Signal utilisationThe gearbox control unit uses the ATF oil temperature to calculate a hot-engine shift program in order to regulate shift pressures as a factor of gear oil temperature. In simplified terms, a high shift pressure is applied at low oil temperature. This pressures is then continuously reduced as a function of rising ATF oil temperature. To prevent the ATF oil from overheating, the engine is revved for longer in the individual gears and the lock-up clutch is closed more frequently when the oil temperature exceeds 150° Celsius. These measures reduce friction and allow the oil to cool down.41Electronic components - The sensorsEffects of signal failureIf the signal from sender G93 fails, the hotengine shift program is no longer received, with the result that the gearbox performs gearshifts at higher pressures. The control unit utilises the signal from the coolant temperature sender up to a temperature of 70° C. It then utilises a fixed value of 110 °C.Electrical circuitJ217232_182G9342Multi-function switch F125This is located on the exterior of the gearbox housing. It is actuated by the selector lever cable.232_064In previous automatic gearboxes, mechanical circuits were used in the multi-function switch. The mechanical circuits have now been replaced by Hall senders. The non-contact switches are wear free. For inspection and repair work, please refer to the relevant Workshop Manual.Signal utilisation The multi-function switch detects the position of the selector lever and passes this information on to the gearbox control unit. The control unit initiates the required gearshifts and activates the starter inhibitor relay if the selector lever is in »P« or »N« position.Effects of signal failure If the multi-function switch fails, the engine can only be started in selector lever position »P«. If it fails while travelling, the control unit reverts to automatically to selector lever position »D«. In both cases the control unit no longer accepts a forward selector lever position request from the driver. It shifts all forward gears electrically. The driver need only engage reverse gear.SElectrical circuitJ217F125232_17843Electronic components - The sensorsTiptronic switch F189is located on the selector lever mechanism. If the driver engages the selector lever in the right selector gate, the Tiptronic switch is actuated and the automatic gearbox enters Tiptronic mode.232_225Signal utilisationBased on this signal, gears are selected as follows: ● Move selector lever forward (+) to change up one gear ● Move selector lever backward (-) to change down one gear.Effects of signal failureTiptronic mode cannot be activated.Electrical circuit J217 F189 E20 Automatic gearbox control unit Tiptronic switch Switches and instruments - lighting controlF189 E20J217232_18144Brake pressure switch F270This is integrated in the brake circuit. It supplies the automatic gearbox control unit with a signal indicating when brake pressure has been built up.Automatic gearbox Control unit Brake pressure switch232_175Signal utilisationThe gearbox control unit utilises the signal from the brake pressure switch to control the stationary decoupling of the gearbox. At present, stationary decoupling is only performed on diesel engined vehicles. Stationary decoupling suppresses the vehicle's tendency to creep. This improves fuel economy and reduces exhaust emissions. When the vehicle stops (e.g. at traffic lights), the gearbox control unit disengages the gear.Effects of signal failure- No stationary decoupling45Electronic components - The sensorsData transfer via the CAN busEngine speed This is detected by the engine speed sender and transferred to the engine control unit. The engine control unit sends this information to the automatic gearbox control unit via the CAN bus.Automatic gearbox Control unitEngine control unit232_163Engine speed senderSignal utilisationThe gearbox control unit utilises the engine speed to control the torque converter lock-up clutch and stationary decoupling.Effects of signal failure- The lock-up clutch is no longer closed, - no stationary decoupling.46Brake light switch FFor safety reasons, there are two brake light switches on the brake pedal. Both switches send a »brake operated« signal to the engine control unit. The engine control unit then sends this signal to the automatic gearbox control unit via the CAN bus.Automatic gearbox Control unitEngine control unit232_172Brake light switchSignal utilisationWhen the vehicle is stationary, the control unit releases the selector lever lock after it receives the corresponding signal from the brake light switch. If a travelling vehicle is braked while the lock-up clutch is closed, the gearbox control unit opens the torque converter lock-up clutch.Effects of signal failureIf one of the two signals is received, the functions remain active. If both signals fail, then the selector lever can be operated without depressing the brake pedal.The engine control unit self-diagnostics stores the brake light switch fault.47Electronic components - The sensorsKick-down switch F8This switch is only used in vehicles without electronic accelerator. By operating this switch, the driver indicates to the control unit that he wishes to accelerate at full throttle. The relevant data is transferred over the CAN bus.Automatic gearbox Control unit Engine control unit232_176Kick-down switchSignal utilisationAfter the »kick-down« command is given, the control unit selects a special shifting characteristic which revs the engine for longer in the individual gears. To accelerate the vehicle more quickly, a downshift is executed depending on actual engine speed after the kick-down command is given.Effects of signal failureIf the signal fails, the engine control unit calculates a substitute signal from the position of the accelerator pedal.48Further CAN signals which are used as input variables for the gearbox control unit include:the signal from the ABS control unitIf the driving situation requires the ABS control unit to employ the Traction Control System (TCS) or the Electronic Stability Program (ESP), then the ABS control unit passes this information on to the CAN bus.Automatic gearbox Control unitABS control unit232_177Signal utilisationIf the gearbox control unit is informed that the TCS or ESP have intervened to compensate for loss of traction or instability, the control unit performs no gearshifts during the intervention period.Effects of signal failureIf the automatic control unit does not receive any signals from the ABS control unit, the gearbox continues to perform gearshifts even if TCS or ESP are activated.49Electronic components - The output signalsThe gearbox control unit receives data signals from other control units and sends the same information to the other control units.Signal for selector lever position to engine control unitThe signal for selector lever position is an analogue signal and is supplied to the engine control unit over an electric wire.Automatic gearbox Control unit Engine control unitMulti-function switch F125232_222Signal utilisationThe engine control unit uses the selector lever position signal tode-activate the cruise control system in the »P«, »N« and »R« selector lever positions.Effects of signal failureThe cruise control system is not functional.50The signal from the road speed senderThe signal is sent to other control units via the CAN bus.Automatic gearbox Control unit Engine control unitRoad speed sender G68232_223Signal utilisationThe control unit in the dash panel insert uses the signal for the speedometer.Effects of signal failureThe control unit in the dash panel insert calculates a substitute value from the gearbox speed sender G38 signal.51Electronic components - The actuatorsSolenoid valvesNine solenoid valves are located in the valve body of the automatic gearbox. They are activated for gear changing by the automatic gearbox control unit. There are two types of solenoid valve which have different operating mdoes:yes/no valves andmodulation valves.Six of the nine solenoid valves are yes/no valves. They can either fully open or completely close an oil gallery. Intermediate settings are not possible. These valves are numberedThe other three solenoid valves are modulation valves. They not only have the circuit states »fully open« and »fully closed« but can also be steplessly adjusted. These valves are numbered N91, N93 and N283.N88, N89, N90, N92, N281 and N282.Layout of solenoid valves in the valve bodySolenoid valve N88Solenoid valve N92Solenoid valve N281Solenoid valve N89Solenoid valve N93Solenoid valve N91Solenoid valve N90 Solenoid valve N283 Solenoid valve N282232_08252The yes/no valvesSolenoid valves N88, N89 and N92N88N92They are responsible for gear changingN89232_087The table shows which of the three solenoid valves is activated in the individual gears by the control unit. (+) = activatedSolenoid valve Gear 1. 1. Tip 2. 3. 4. 5. R. + + + + N88 + N89 + + + + + + + N92 + +Electrical circuitN88 N89 N92Even if a single valve fails, the gearbox control unit reverts to emergency mode.53Electronic components - The actuatorsSolenoid valve N90is activated to open and close clutch K1 depending on driving conditions. Solenoid valve N90 is also activated if the reverse gear is engaged while the vehicle is moving forwards. This prevents clutch K2 for the reverse gear from closing. When driving away, the main ATF oil pressure is increased by this solenoid valve.N90232_088Effects of signal failure- The control unit does not select 5th gear. - Stationary decoupling is not carried out.Electrical circuitJ217N90232_18854Solenoid valve N281This maintains the ATF oil pressure on brake B3 in gears 1 to 4 and in reverse while the pressure on the other clutches and brakes is reduced during gear changes.N281232_089Effects of signal failureIf this solenoid valve fails, brake B3 is kept closed and this results in slightly harsher downshifts.Electrical circuitJ217N281232_19255Electronic components - The actuatorsSolenoid valve N282This solenoid valve is activated by the control unit when brake B2 is opened or closed. It is closed in 2nd, 4th and 5th gear. Together with solenoid valve N90, this solenoid valve decouples the gearboxes of diesel-engined vehicles when stationary.N282232_090Effects of signal failure- The vehicle can only be driven in 4th gear and in reverse. - Stationary decoupling is not carried out.Electrical circuitJ217N282232_19056The modulation valvesSolenoid valve N93This regulates the main oil pressure for the entire automatic gearbox depending on driving conditions. It ensures smooth running and joltfree gear changes.N93232_091Effects of signal failure- The main oil pressure is not regulated, resulting in harsh gearshifts, - no stationary decoupling.Electrical circuitJ217N93232_19157Electronic components - The actuatorsSolenoid valve N283This regulates the ATF oil pressure of brakes B2 and B3. Brake B2 is closed in 2nd, 4th and 5th gear while brake B3 is closed in 1st, 2nd, 3rd, 4th and reverse gear.N283232_092Effects of signal failure- The maximum main oil pressure is applied to the brakes, resulting in harsh gearshifts - no stationary decoupling.Electrical circuitJ217N283232_18958Solenoid valve N91This regulates the pressure during the opening and closing movements of the torque converter lock-up clutch. To close the torque converter lock-up clutch, the solenoid valve is energised by the control unit.N91232_093Effects of signal failure- The torque converter lock-up clutch is no longer closed.Electrical circuitJ217N91232_19359Electronic components - The actuatorsSelector lever lock solenoid N110It is located in the selector lever mechanism. It prevents the gear lever from being moved from selector lever positions P and N into other positions. The selector lever lock is cancelled when the brake is operated. The lock is activated when the driver turns on the ignition.232_194Effects of signal failure If the solenoid for selector lever lock fails, the selector lever can be engaged in a drive position without the driver having to depress the brake pedal. If both brake light switches fail, the selector lever can no longer be moved. If fault in the brake light switch is stored in the self-diagnostics of the engine control unit.232_195Electrical circuitJ217232_184N11060Selector lever display illumination L101 and selector lever position P/N warning lamp K142are integrated in Tiptronic switch F189. The brightness of the selector lever display illumination can be adjusted by switches and instruments-lighting control E20.232_226232_197The selector lever position P/N warning lamp indicates when the lever is in these two positions. It serves to remind the driver that the brake pedal has to be depressed in order to move the selector lever out of these positions.232_198SElectrical circuit J217 F189 E20 K142 L101 Automatic gearbox control unit Tiptronic switch Switches and instruments - lighting control Selector lever position P/N warning lamp Selector lever display illuminationF189 K142L101N110 J217E20232_19661Function diagramComponents F125 Multi-function switch F189 Tiptronic switch F270 Brake pressure switch G68 Road speed sender G182 Gearbox input speed sender G265 Intermediate shaft speed senderB S SJ217 J226Automatic gearbox control unit Starter inhibitor and reversing light relay Selector lever position P/N warning lampJ226N110K142L101Selector lever display illuminationA CN88 N93 Solenoid valves N110 Selector lever lock solenoid N281N283 Solenoid valves S FuseAuxiliary signals A B C D E F G H I K L to the reversing lights to the ignition switch to the starter Terminal 50 Road speed signal Road speed signal Self-diagnostics CAN - high CAN - low Switches and instruments lighting control Selector lever position to engine control unit Signal for cruise control systemF12562SSSK142L101G68G182G265F189IFGHLJ217DEKG93 F270N88 - N93 N281 - N283232_01463Self-diagnosticsThe self-diagnostic function of the automatic gearbox independently monitors the signals from the sensors as well as the actuator activation signals, and checks the control unit. If faults occur, substitute functions are made available and the fault is stored in the control unit's fault memory. The control unit has a non-volatile fault memory. The means that the contents of the fault memory are kept even if the control unit is temporarily disconnected from the power supply.The new vehicle diagnostic, testing and information system VAS 5051 is used for faultfinding and reading out the fault memory. This device includes all the tools required for fault-finding in electronic vehicle systems. The user can run the guided fault finding routine or carry out test procedures using the test instruments.210_102The following functions can be invoked in the self-diagnostics under the address word 02 »Gearbox electronics«: 01 02 04 05 06 08 »Interrogate control unit version«, »Read out fault memory«, »Start basic adjustment«, »Clear fault memory«, »End of output« and »Read data block«.64Function 01Interrogate control unit versionSpare part No. of control unit 09A927750 Gearbox designation AG5 gearbox 09A Program version 0004WSC 0000Workshop codeFunction 02Interrogate fault memory The colour-coded sensors and actuators are detected by the self-diagnosis function and stored in the fault memory.G265 J217 G68 N110 G182 N88, N89, N90, N92, F125 N281 N91, N93, F189 N282G93L101 K142F270 210_20065Self-diagnosticsFunction 04Basic setting On completion of repair work on the accelerator pedal sender or after replacing the engine control unit, carry out a basic setting procedure. As with the 4-speed automatic gearbox, iyou must carry out the basic setting procedure after you replace the control unit.Function 08Read data block Signals from the components highlighted in colour can be tested in the measured value block.G265 J217 G68 N110 G182 N88, N89, N90, N92, F125 N281 N91, N93, F189 N282G93L101 K142 ABSF270J285210_19966ServiceSpecial tools In keeping with the care concept for the 5-speed automatic gearbox, the following new special tools are required to carry out repair work.Pressure piece T 10087for installing the shaft oil seal210_205Pressure piece T10088for installing the left and right flange shafts210_204Pressure piece T10089for fitting the oil seal on the torque converter210_203Pressure piece T10090for fitting the oil seal on the selector shaft210_202Adjustment plate 3282/32for removing the gearbox from the vehicle210_201T10091for adjusting the multi-function switch210_22467Test your knowledge1. In what selector lever position does 1st gear use the engine brake? a) 1st gear always uses the engine brake. b) in selector lever position "D" only c) in the Tiptronic selector gate only2.How many planetary gears are there in the AG5? a) 2 Ravignaux planet gear sets b) 3 planetary gears c) 4 planetary gears3.Via which components is torque transmitted to the planetary gears? a) via the sun gear of planetary gear II and via clutch K3 b) via clutch K1 and clutch K2 c) via clutch K3 only4.What clutches equalise centrifugal force in the AG5? a) clutch K4 only b) clutches K2 and K4 c) clutches K1 and K35.Are there different types of brake in the AG5? If yes, name them. a) no b) yes 1. _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2. _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _686.Identify the components!232_060697.What is the task of the pressure accumulators? a) They regulate the main oil pressure of the automatic gearbox. b) They are responsible for ensuring the soft closing of clutches K1, K3 and K4 as well as brake B2 . c) B3 is activated by the pressure accumulators.8.How many solenoid valves are located in the valve body of the automatic gearbox? a) 7 b) 8 c) 99.Gearshifts are initiated by the different solenoid valve closing combinations. What are the electrical designations of the 3 solenoid valves? a) N88, N89 and N92 b) N91, N93 and N28210.Three engine speed sensors with identical design and operating principles are located in the automatic gearbox. According to what electrical operating principle do they work? a) their function is based on the Hall principle. b) their function is based on the induction principle.7071Solutions 1.) c 2.) b 3.) a 4.) c 5.) b 6.) see page 16 7.) b 8.) c 9.) a 10.) b232For internal use only © VOLKSWAGEN AG, Wolfsburg All rights reserved. Technical specifications subject to change without notice. 040.2810.51.20 Technical status: 5/00❀ This paper is produced fromnon-chlorine-bleached pulp.