TECHNICAL DOCUMENTATION
SSP 248 The W Engine Concept

This PDF is currently unavailable.
Read document text
Service.Self-Study Programme 248The W Engine ConceptDesign and FunctionIntroductionThe constantly rising demands regarding performance, running comfort and fuel economy have led to the advancement of existing drive units and the development of new drive units. The new W8 as well as the W12 engine by VOLKSWAGEN are representatives of a new engine generation - the W engines. The W engines set exacting demands on design. Large numbers of cylinders were adapted to the extremely compact dimensions of the engine. In the process, more attention was paid to lightweight design. This Self-Study Programme will familiarise you with the engine mechanicals of the W engine family.S248_101NewImportant NoteThis Self-Study Programme explains the design and function of new developments. The contents will not be updated!Please always refer to the relevant Service Literature for current inspection, adjustment and repair instructions.2At a glanceIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Engine mechanicals . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 The crankshaft drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 The engine in detail . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 The chain drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 The camshaft timing control . . . . . . . . . . . . . . . . . . . . 29 The belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 The oil circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 The coolant circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 The air supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 The exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Sealing concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Engine timing overview. . . . . . . . . . . . . . . . . . . . . . . . . 54 Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563IntroductionW engines - what does the W stand for?With the aim of building even more compact units with a large number of cylinders, the design features of the V and VR engines were combined to produce the W engines. As with the V engines, the cylinders are distributed to two banks. In the W8 and W12 engines, these banks of cylinders are aligned at a V-angle of 72° in relation to one another. As in the VR engine, the cylinders within each bank maintain an angle of 15°. When the W engine is viewed from the front, the cylinder arrangement looks like a double-V. Put the two Vs of the right and left cylinder banks together, and you get a W. This is how the name "W engine" came about.72°15°S248_10415°S248_002S248_0014The W principleTo illustrate the principle of the W engine cylinder arrangement, we will first show you conventional engine types.The inline engine Represents the earliest development level in engine development. The cylinders are arranged in-line vertically above the crankshaft. Advantage: Simple design Drawback: Large numbers of cylinders result in very long units unsuitable for transverse mounting.S248_003S248_004The V engine To make engines shorter, the cylinders in the V engines are arranged at an angle of between 60° and 120°, with the centre lines of the cylinders intersecting with the centre line of the crankshaft. Advantage: Relatively short engines60 - 120°S248_005Drawback: The units are relatively wide, have two separate cylinder heads, and therefore require a more complex design and a larger engine compartment volume.S248_0065IntroductionVR engines The need for a powerful alternative suitable for transverse mounting for use in lower mid-range vehicles saw the development of the VR engine. Six cylinders, offset at a V-angle of 15°, are accommodated in a fairly slender and very short engine block. Unlike previous designs, the engine only has one cylinder head. This made it possible to supply the Golf with a compact VR6 cylinder engine, for example.15S248_007S248_008W engines The engines of the W family are a combination of two "VR banks" based on a modular design principle. The cylinders of one bank have an angle of 15° relative to each other while the two VR banks are arranged at a V-angle of 72°.S248_00972°15S248_0106The modular design principle of the W enginesProven, serial-produced components from the modules of the VR engine family were integrated into the new W engine concept. The principle is very simple. Two compact VR engines from the VR series are combined to produce a W engine. The result is a series of compact petrol engines ranging from the W8 to the W16. Numerous components of the VR and W series are identical, e.g.: - valves, valve springs and valve seat inserts - roller rocker fingers - valve clearance compensating elements This allows us to manufacture many parts in series and achieve high volumes.6 cylinder V engine6 cylinder VR engine6 cylinder inline engine72°W16 W12 W16 2xW82xVR6W12S248_105S248_011With regard to the evolution of the 6-cylinder engine, the VR6 engine stands out due to its compactness. It is much shorter than the comparable inline engine, and narrower than the V engine. Combining two VR6 engines with a cylinder angle of 72° produces a W12 engine.A W16 engine is obtained by joining two cylinders to each cylinder bank of a W12 engine. Splitting the W16 in the middle leaves two W8 engines. A W10 engine consisting of two VR5 engines is also a possibility. This covers the complete range of W engines.7IntroductionA comparisonWhen a conventional 8-cylinder V engine (comparable displacement) is compared to an 8cylinder W engine, the latter particularly stands out due to its compact design and very small external dimensions. This is also reflected in a comparison of the crankshafts. The compact design of the 12cylinder W engine is highlighted by the fact that it has even smaller external dimensions than a conventional V8 engine.The W8 engineThe V8 engineS248_014 S248_012W8 crankshaftV8 crankshaft8Comparing the 12-cylinder crankshaft of a conventional V12 engine with that of a 12cylinder W engine emphasises the constructional advantage.Depending on the number of cylinders, the W principle therefore saves material, and hence also weight.The W12 engineThe crankshaft of a V12 engine with the most available space is shown by way of comparisonS248_013S248_150W12 crankshaftV12 crankshaft9Engine mechanicalsSpecifications - the W8 engineS248_017Displacement [cc] Bore [mm] Stroke [mm] Number of cylinders Number of cylinder heads Offset [mm] Bank offset [mm] V-angle of cylinder heads [°] of both banks V-angle of cylinders [°] in a bank Number of valves Splitpin (crankshaft journal offset) Firing order3999 84 90.168 8 2 ± 12.5 13 72° 15 4 / cylinder -18° 1-5-4-8-6-3-7-210Torque and power output [Nm] 500[kW] 200400150300100200 S248_018 100 2000 4000506000 rpm S248_021Torque curve Output curveEngine code Dimensions (l x w x h) [mm] Weight [kg] Max. output [kW] ([bhp]) Max. torque [Nm] FuelBDN 420 x 710 x 683 approx. 193 202 (275) 370 98 RON to DIN EN 228 The engine may also be operated alternatively with 95 RON unleaded premium fuel with a slight reduction in performance and torque. Bosch Motronic ME7.1 in-line 5HP19 4-Motion, C90 6-speed 4MotionEngine management system Installation position Allocated gearbox11Engine mechanicalsSpecifications - the W12 engineS248_019Displacement [cm3] Bore [mm] Stroke [mm] Number of cylinders Number of cylinder heads Offset [mm] Bank offset [mm] V-angle of cylinder heads [°] of both banks V-angle of cylinders [°] in a bank Number of valves Splitpin (crankshaft journal offset) Firing order5998 84 90.168 12 2 ± 12.5 13 72° 15 4 / cylinder +12° 1-12-5-8-3-10-6-7-2-11-4-912Torque and power output [Nm] 800 700 600 500 400 300 200 100 2000 4000 [kW] 400 350 300 250 200 150 100 50 6000 rpm S248_022 Torque curve Output curveS248_020Engine code Dimensions (l x w x h) [mm] Weight [kg] Max. output [kW] ([bhp]) Max. torque [Nm] FuelBAN 513 x 710 x 715 approx. 245 309 (420) 550 98 RON to DIN EN 228 The engine may also be operated alternatively with 95 RON unleaded premium fuel with a slight reduction in performance and torque. Bosch Motronic ME7.1.1 (dual control unit concept) in-line 5HP24 4MotionEngine management system Installation position Allocated gearbox13Engine mechanicalsThe crankshaft driveThe offsetCentre of cylinder Centre of cylinderThe cylinders of a bank are offset in a tandem arrangement and positioned at a very narrow angle of 15°. The compact W engine was made possible by arranging two banks at an angle of 72°. To provide adequate space for the pistons in the bottom dead centre range, it was necessary to offset the crankshaft drive. This means that the cylinders are offset by 12.5 mm outwards relative to the centre of the engine (crankshaft fulcrum).15Offset 12.5 mm leftOffset 12.5 mm rightThe crank pin offset A constant spark gap is maintained by the crank pin offset, or what is known as the 'splitpin'. The layout of the W engine is based on a 10cylinder engine. All cylinders in a 4-stroke engine fire within a crank angle of 720°. W10 engine 720° crankshaft : 10 cylinder = 72° bank angle W8 engine 720° : 8-cylinder = 90° spark gap 72° bank angle - 90° spark gap = Splitpin -18° W12 engine 720° : 12 cylinder = 60° spark gap 72° bank angle - 60° spark gap = Splitpin +12°Middle of crankshaft Point of intersection of centres of cylindersS248_186W12 engine 21.833° 1 7 12° 6 128 2 11 5 4 103 9S248_02614The engine in detailTo familiarise you thoroughly with the mechanical construction of the W8 and W12 engines, we will now describe the main modules of both engines in succession. The following topics will be dealt with: the crankcase with bearing support, the crankshaft with conrods and pistons, the balancing shafts, the cylinder heads, the oil sump and oil pump, the crankshaft drive, the timing chain drive, the belt drive for auxiliary components and the multi-part intake manifoldW8 enginethe multi-part intake manifoldthe cylinder headsthe crankshaft with conrods and pistonsthe crankcase with bearing supportthe split oil sump with oil pump. S248_02515Engine mechanicalsThe crankcase The crankcase comprises two components: the crankcase upper section and the crankcase lower section. The upper section contains, among other things, the cylinders and the upper bearing cover halves of the crankshaft. The crankcase lower section is designed as a bearing support and carries the lower bearing cover halves.W12Crankcase upper sectionW8S248_028Crankcase lower sectionS248_027The crankcase upper section The "aluminium" crankcase upper section is made of a hypereutectic aluminium-silicon alloy (AlSi17CuMg). Hypereutectic means that pure silicon crystals initially precipitate out of the aluminium-silicon melt while it cools before aluminium/silicon crystals form. Due to the presence of these silicon crystals within the metal microstructure, the cooled melt is harder than a eutectic Al-Si alloy. Use of this alloy eliminates the need for additional cylinder liners or a plasma coating for the purposes of cooling and lubricating the cylinder surfaces as the material already has sufficient natural strength and thermal stability.16The crankcase lower section The crankcase lower section is a bearing support with integral bearing seatsBearing coverS248_033S248_030 Cast element in bearing supportW12 bearing supportS248_032W8 bearing supportCasing opening towards drive of balancing shafts S248_029The bearing support is also made of aluminium. It serves as a frame structure for the lower crankshaft bearing covers. These bearing covers are made of grey cast iron and are also embedded when the bearing support is cast.They are located on the pressure side of the crankshaft and give the crankshaft bearing the strength it requires. The bearing support is attached to the crankcase upper section by 4 bolts per bearing cover.17Engine mechanicalsThe crankshaftW8 crankshaftThe crankshafts used in the W engines are manufactured from forged tempered steel. In each case, two conrods run between two main bearings.S248_036Journals for driving the oil pump and the balancing shaftMain bearingConrod journalGears for the doublechains of the chain driveS248_037Crankshaft journal Toothed belt pulley Balancing shafts Main bearing Crankshaft of the W engine family with corner radii S248_043Vibration absorber S248_056 Gear Oil pump S248_045The drive gear of the oil pump, together with the toothed belt pulley for the balancing shafts (on the W8 engine only), is pressed against the outer main bearing and fixed in place by the vibration absorber.The conrod journals are arranged in pairs and in accordance with the crankshaft throw. When the conrods are installed, the bearing cups must not contact the radii or the edge between the two conrod faces (use tool).18Conrods and pistons The conrods are made of forged steel and are only 13 mm thick. They are of a trapezoidal construction and are cut during the production process. To ensure better oil exchange, two grooves are milled in the side faces of the conrod lower sections. The conrod pin is lubricated through two inclined bores in the conrod head.Trapezoidal shapeBoresS248_048S248_047 S248_016 Grooves for oil exchangeDrainage holesThe pistons are made of an aluminium-silicon (Al Si) alloy. The recess in the piston surface is very shallow as the cylinder head takes up most of the combustion chamber volume. The inclined piston surface is necessary because of the V-position adopted by the pistons. Each piston carries 2 piston rings and an oil taper ring. To drain off the oil which collects in the scraper ring, small drainage holes lead into the piston ring groove towards the inside of the pistonS248_049S248_050Iron (Fe) coating for Al Si liners in central crankcase19Engine mechanicalsThe balancing shaft of the W8 engine The W8 engine has two balancing shafts for compensating the forces of inertia. The two shafts are housed in the crankcase. The upper balancing shaft is driven by the crankshaft by means of a toothed belt. A gear located at the end of the upper balancing shaft drives the lower balancing shaft. The balancing shafts are mounted in two location holes on the clutch side of the crankcase.Installation openingsS248_055Drive gear on the crankshaft Tension pulleyAlign marker on balancing shaft drive gear with the marker on the sealing face (TDC of 1st cylinder).S248_057Bearing in bearing bushes of the crankcaseAlign marker on crankshaft drive gear with the joint (TDC of 1st cylinder).Drive gear on the balancing shaft20There is a groove at the gear wheel end of the balancing shaft. The lock plate engages into this groove, locating the balancing shafts axially. During installation, the balancing shafts must be aligned with regard to the TDC position of the 1st cylinder. The balancing shafts must be rotated so that the markings on the balancing shafts are opposite each other.Gears of the balancing shaftsMarkingPosition of balancing shafts at TDC of 1st cylinder Lock plateS248_108Balancing shaft IS248_107 S248_054 Drive Balancing shaft II Locking groovesS248_058S248_059The balancing shaft drive is protected on the belt drive side by a plastic housing cover.On the clutch side, the openings for inserting the balancing shafts, together with the chain drive, are sealed by an aluminium cover.21Engine mechanicalsTwo-mass flywheel with clutchW engines fitted with a manual gearbox generally have a two-mass flywheel. This flywheel prevents torsional vibration from being transmitted by the crankshaft to the gearbox via the flywheel. This would otherwise adversely affect handling performance.S248_060Two-mass flywheelClutch coverClutch discS248_06122A spring damper system within the two-mass flywheel separates the primary inertia mass from the secondary inertia mass so that the torsional vibration produced by the engine is not transmitted to the gearbox. On W engines with automatic transmission, the two-mass flywheel is substituted by a converter plate.S248_061Two-mass flywheelTooth gapPulse sensor wheelS248_062The two-mass flywheel also serves as a sender wheel. Its job is to determine the engine speed and recognise cylinder No. 1 together with the Hall senders of the camshafts. It has a larger tooth gap which serves as a marker point. This point is registered by the engine speed sender located in the gearbox housing during each revolution of the two-mass flywheel.23Engine mechanicalsThe cylinder heads The W engines have two aluminium cylinder heads with two overhead camshafts apiece. The injectors are inserted into the cylinder heads.Cylinder heads of W8 engine Opening for injector Camshaft bearing - intakeCamshaft bearing exhaustS248_063Each of the cylinder heads in the two W engines has an intake camshaft and an exhaust camshaft with camshaft adjusters attached to their end faces.S248_067 Camshaft adjuster Roller rocker finger Camshafts24CamshaftThe 4 valves in each cylinder are actuated by low-friction roller rocker fingers. Valve clearance is compensated by hydraulic support elements.Cam roller Roller rocker fingerValveS248_160 Hydraulic support elementS248_161Due to the cylinder arrangement, short and long valves as well as short and long inlet and exhaust ports alternate with one another.25Engine mechanicalsIntake manifold of W12 engine Air supply intakeCylinder heads of W12 engineS248_170Intake valve Intake portsS248_171Exhaust valveExhaust ports26The secondary air ducting system Beside the coolant and oil ducts, the secondary air is guided via ducts and bores into the exhaust ducts near the exhaust valves. The secondary air flows into a duct in the cylinder head via a secondary air inlet valve. From here the secondary air is guided back into the cylinder head via grooves in the exhaust flange. The secondary air then flows via ducts and bores to the exhaust valves.S248_169 S248_172 Connection for secondary air inlet valve Groove in exhaust flangeBores leading to exhaust valve (internal)Bores leading to exhaust Oil return holes valve (external)Exhaust valves Secondary air duct (external)Exhaust valves (internal)Coolant Oil ducts Secondary air S248_17427Engine mechanicalsThe chain driveThe chain drive is mounted at the flywheel end of the engine. Engine power is transmitted by a gear on the crankshaft to the gears of the central intermediate shaft by means of a double-chain. At this point, each of the camshafts of the two cylinder heads is driven by means of a single chain. Three hydraulic chain tensioners ensure that an optimal chain tension is maintained.Chain drive of W enginesCamshaft adjusterTensioning railChain tensionerSlide railInlet camshaftCentral intermediate shaftExhaust camshaftSingle chain (sleeve type chain) Left bank Single chain (sleeve type chain) Right bank Slide rail Chain tensioner Double chain (roller chain) Tensioning railGear on crankshaftChain tensioner with tensioning railS248_07528The camshaft timing controlLike the W12 engine, the W8 engine has continuous camshaft engine timing control. In this case, "continuous" means that the inlet camshaft can be advanced/retarded relative to its neutral position at any angle within a range of 52°. The camshaft is adjusted by hydraulic camshaft positioners bolted to the end face of each camshaft. The exhaust camshaft of the W8 engine is an exception. It can only be adjusted to the "advance" or "retard" position within a range of 22°. The engine control unit regulates the oil supply to the camshaft positioners via the solenoid valves.Timing caseS248_176Vane adjuster Inlet camshaftSolenoid valve N205Solenoid valve N318Vane adjuster Exhaust camshaftS248_12829Engine mechanicalsSystem design Neutral position When the solenoid valve moves the adjusting piston into a central position, this causes both oil ducts (a+b) - and hence the chambers (A+B) on either side of the inner rotor - to fill with oil. The inner rotor, together with the camshaft which it is rigidly coupled to, now adopts a position in the middle of the adjustment range.Solenoid valve Adjusting pistonOil duct (a) Oil duct (b) Oil duct (aa) Chamber (B) Oil duct (bb)Oil return passage Engine oil pressure Oil return passageInner rotor (rigidly coupled to camshaft)Chamber (A)Outer rotor (coupled to timing chain) Annular ducts S248_135Camshaft neutralStop Retard adjusterInlet camshaft Exhaust camshaftBank IStop Advance adjusterChamber (A)Inner rotor Chamber (B) Outer rotor Direction of rotation of drive S248_13930Retard adjustment The solenoid valve guides the oil into the oil duct (b). The oil flows from channel (b) through the annular groove and camshaft and via the bores (bb) to the chambers (B) of the camshaft adjuster. When the oil enters the chambers (B), the inner rotor is rotated against the direction of rotation of the drive, thus adjusting the camshaft in the retard direction. The oil is forced out of the chambers (A) through the bores (aa). It flows back into the cylinder head via the camshaft and duct (a).Bank ICamshaftRetard stopIntake camshaftExhaust camshaftChamber (A)Inner rotor Chamber (B) Outer rotor S248_138Advance adjustment To rotate the inner rotor forwards, the adjusting piston housed within the solenoid valve adjusts itself so that the oil duct (a) is put under oil pressure. As a result, the oil flows in the chamber (A), thus advancing the inner rotor. Chamber B is simultaneously bled via the solenoid valve so as to ensure a quick response.Bank ICamshaft Advance stop Intake camshaft Exhaust camshaftChamber (A)Inner rotor Chamber (B) Outer rotor S248_13731Engine mechanicalsThe belt driveThe following units and devices are driven by the belt drive: the coolant pump the alternator the power steering pump the air conditioner compressorThe poly-V-ribbed belt is tensioned by a hydraulic tensioning and deflection pulley. 2 deflection pulleys ensure that all units to be driven can be reached.Belt drive of the W8 engine and W12 engine in the VW "D1"Water pumpHydraulic belt tensioner with deflection pulleyDeflection pulleyAir conditioner compressorAlternatorDeflection pulleyVibration absorberPower steering pumpS248_07732In the W12 engine, the hydraulic belt tensioner and deflection pulley are fixed to the air conditioner compressor bracket.Belt drive of the W12 engine in the Audi A8Coolant pumpDeflection pulleyDeflection pulleyHydraulic belt tensionerAir conditioner compressorAlternatorCrankshaft disc with vibration absorberTension pulleyPower steering pump S248_07833Engine mechanicalsThe oil circuitThe oil is drawn out of the oil pan by the oil pump and flows to the central oil passage via the external oil filter/cooler module. The main crankshaft bearings are supplied with pressurised oil via the central oil passage; the central oil duct is supplied with pressurised oil via a riser. The oil from flows from the central oil duct to the spray jets for piston cooling, and then from there to the cylinder heads via risers fitted with nonreturn restrictors. The oil also flows to the intermediate shaft, to the entire engine timing gear and to the chain tensioner. In the cylinder heads, the oil flows along ducts to the camshaft adjusters and the camshaft bearings. The return lines guide the oil back into the oil sump.Oil circuit of the W12 engineSolenoid valve Camshaft timing controlHydraulic elements Camshaft bearing Camshaft adjusterRiser Central oil duct Crankshaft bearing Spray jets for piston coolingReturn ducts Oil sump upper sectionS248_091 Oil pump drive gear Central oil passage Oil sump lower section34Schematic diagram of the oil circuit of the W enginesCamshaft adjusterIntermediate shaftSolenoid valveTiming belt gear 3 chain tensioners with chain oil spray Spray jetReturn line S248_094 Chain Oil pump Oil sumpOil filter/cooler moduleOil sump of the W8 engine Central oil passageS248_08335Engine mechanicalsThe oil circuit based on the wet-sump principle The W8 and W12 engine for VW models have a wet-sump lubrication system. The W12 engine for Audi models has a dry-sump lubrication system.Wet-sump lubrication system of the W8 engineS248_084Oil filter and cooler moduleSingle-stage oil pumpIn the case of the wet-sump lubrication system, the entire oil supply is retained in the oil sump. The single-stage oil pump draws the oil out of the wet sump via the intake line and immediately returns it to the engine after it has cooled down and has been filtered.In contrast to the dry-sump, the job of the oil sump with wet sump is to retain the entire oil supply. As a result, it has a larger volume which affects the overall height of the engine.36The oil circuit based on the dry-sump principleDry-sump lubrication system of the W12 engine in the Audi A8ReservoirThree-stage oil pumpFilterCoolerS248_088In the case of the dry-sump lubrication system, the entire oil supply is retained in an additional, external reservoir, and not in the oil sump. To facilitate this, the oil pump is of three-stage design. Two stages draw the oil out of the oil sump at various points and pump it into the reservoir.The third stage (discharge stage) returns the oil from the reservoir to the engine via the oil cooler and the oil filter. The oil sump can be kept small and flat due to its lower oil volume, with the result that the engine has a smaller overall height. This requires a slightly more complex design.37Engine mechanicalsThe oil sump The oil sump comprises two diecast aluminium parts. The oil sump lower section forms the oil sump. The central oil passage is accommodated in the upper section of the oil sump. Special baffles settle the oil in the oil sump. The sender which informs the engine control unit of the oil level is inserted into the oil sump lower section from below near the oil drain screw, and then bolted.Oil sump upper sectionCentral oil passageS248_079Baffles (swash plates) Oil level senderOil sump lower sectionOil drain screwThe oil pumpDriveIntake lineOil sump lower section S248_082The oil is extracted from the sump by the oil pump via the intake line, and pumped into the oil circuit.The single-stage oil pump is driven by the crankshaft by means of a separate chain in the crankcase.38S248_081The oil pump is mounted from below and bolted to the bearing support.The oil filter and cooler moduleThe oil circuit of the W engine has an external oil filter and cooler module. This allows the engine to be more easily adaptable to the varying amounts of space available in the various vehicle models. The oil filter is designed so that a filter element can be replaced by service personnel.Oil filter/cooler module of the W8S248_09539Engine mechanicalsThe lubrication system The oil in the oil circuit has a lubricating and cooling function. The W engines are filled with type 0W30 3.5 engine oil.The piston spray jets The oil is guided from the central oil duct of the crankcase upper section to small nozzles on the underside of the cylinder bores. Here, the oil is sprayed below the pistons in order to lubricate the piston contact faces and piston pins as well as to cool the pistons.S248_093The crankshaft bearing lubrication system The oil is ducted through bore holes from the central oil passage to the crankshaft. Then it is pumped via a groove on the back of the bearing cups to the upper bearing cup. There it reaches the crankshaft through five bores in the upper bearing cup.CrankshaftUpper bearing cupS248_092 Bearing supportOil supply Groove on the back of the bearing cups40Lubrication of the conrod bearingsS248_175Bore from main bearing to conrod bearingGroove in crankcaseInner groove of bearing cup (in upper bearing only) Inflow to conrod bearingS248_177 Transitional pockets Inflow to main bearingThe oil flows from the outer circumferential groove into the inner groove of the upper bearing cup through five bores. The bore ensures that an even oil film forms. Integrated pockets at the transition to the lower bearing cup ensure a steady supply of oil to the conrod bearings via bores in the crankshaft.41Engine mechanicalsThe coolant circuitThe coolant circuit is filled with VW G12 coolant. The coolant is channelled out of the central coolant duct in the crankcase upper section and into the cylinder heads. Baffles ensure that all cylinders are swept evenly. At the same time, the coolant flow is redirected from the exhaust side of the combustion chambers towards the intake side. The coolant circuit is subdivided into a small circuit, in which the coolant is only ducted within the engine block. An outer circuit is located above the radiator.Coolant circuit of W8 engineHeatingRibbed V-beltCoolant temperature senderRadiatorCoolant pumpThermostat valveS248_098 Oil cooler Alternator Coolant temperature sender at radiator outlet Small cooling circuit Large cooling circuit Equalising vessel42Coolant circuit of W12 engineRight heat exchangerLeft heat exchangerAuxiliary heaterCyclical valve Coolant temperature sender Radiator Auxiliary RadiatorCoolant pumpThermostat valveS248_099 Gearbox oil cooler Alternator Engine oil cooler Small cooling circuit Large cooling circuit Equalising vessel Coolant temperature sender at radiator outlet43Engine mechanicalsThe coolant flow flows from the coolant duct to the crankcase and into the two cylinder heads. In the process, two thirds of the volumetric flow is guided to the outside and one third to the inside of the cylinder head in question. This principle helps to provide even cooling, and is known as cross-cooling.S248_114 Coolant flows into the cylinder headsS248_115Coolant flows through the cylinder heads from the exhaust side to the intake side. This results in very good temperature equalisation as well as effective cooling of the outlet webs and spark plugs.44In both W engines, the coolant pump is located in the cylinder block at the face end. It is mounted directly upstream of the central coolant duct and is driven by the ribbed V-belt.S248_110 Coolant pump with pump gearSwitching over is affected by an electrically actuated thermostat valve. In the W8 and W12 engine, this valve is installed in the crankcase upper section from above. To replace this valve, it is necessary to remove the intake manifold. By electrically activating the thermostat valve, it is possible to control the switching point and coolant temperature. Characteristic maps are stored in the engine control unit. They make it possible for the engine to reach the desired temperature in accordance with the engine's operating requirements.S248_111S248_112For detailed information, please refer to SSP 222.Heating resistorS248_179Wax thermo-coupleElectrical thermostatic valve for mapped coolingLifting pin45Engine mechanicalsThe air supplyAir is supplied through a tapered intake pipe. It is of a four-part design and is made of an aluminium alloy. The intake manifold lower section is bolted to the cylinder heads between the two cylinder banks. The larger intake manifold upper section is mounted to the lower section. The intake manifold upper section is designed so that the manifolds for bank I and II can be detached separately. The makes it easier to gain access to the individual ignition coils and spark plugs, for example. In the W8 engine, the intake air for both manifolds is guided by a throttle valve control unit.W8 engine Intake manifold upper sectionManifold, bank IManifold, bank IIIntake manifold lower sectionS248_116S248_117Throttle valve control unitS248_11846W12 engine Intake manifold upper sectionThe intake manifold used in the W 12 engine is made of magnesium alloy. Unlike the W8 engine, each of the manifolds is coupled to a throttle valve control unit.Manifold, bank I Intake manifold lower sectionManifold, bank II S248_119S248_120Throttle valve control unitS248_12147Engine mechanicalsThe crankcase breatherThe diaphragm valve limits the vacuum in the crankcase irrespective of the intake pipe vacuum, allowing the cleaned crankcase exhaust gases (blow-by) to be abducted continuously into the intake manifold and burnt in the engine. No oil is entrained in the process. The oil separator segregates the oil particles from the blow-by gas. The separated oil is then returned to the oil sump.W8 engine Diaphragm valveS248_122 Oil separator48W12 engine Diaphragm valve, leftOil separatorS248_123Diaphragm valve, rightOil separatorS248_129As the W12 engine has a double flow intake manifold, each bank has a side diaphragm valve and an oil separator.49Engine mechanicalsThe exhaust systemThe W8 engine has an exhaust manifold with a permanently assigned catalytic converter for each cylinder head. A total of four lambda probes are therefore required for emission control. The exhaust system has primary silencer and a rear silencer for each bank, as well as a common central silencer.Lambda probe Rear silencer Central silencer Primary silencerManifoldCatalytic converter TailpipesExhaust system of W8 engineS248_124S248_12550Primary silencer Rear silencer Central silencerLambda probe after catalytic converterLambda probe before catalyticconverter Primary catalytic converterManifoldMain catalytic convertersTailpipesLambda probe dowstream of catalytic converter Primary catalytic converter Lambda probe upstream of catalytic converterExhaust system of W12 engine S248_126The W12 engine has two exhaust manifolds for each cylinder head. Each of these exhaust manifolds is connected to its own primary catalytic converter located near the engine. The two exhaust pipes of each bank then merge on a main catalytic converter. The exhaust system has a primary silencer, an intermediate silencer and a rear silencer for each bank. Four primary catalytic converters and two main catalytic converters help to achieve an effective reduction in emissions. To monitor mixture combustion and to optimise pollutant emission reduction, use is made of four lambda probes before the catalytic converter and after the catalytic converterExhaust manifoldS248_12751ServiceSealing conceptEach of the cylinder heads is sealed off from the valve covers by a rubber gasket, from the contact faces of the intake manifold by an elastomer gasket, from the exhaust manifolds by a two layer embossed metal gasket and from the crankcase by a multilayer embossed metal gasket. The gasket between the bearing support and the oil sump upper section is also designed as a single layer embossed metal gasket. The oil pan upper section and lower section as well as the crankcase upper section and the bearing support are sealed by means of a liquid gasket.Multilayer metal/elastomer composite gasket between cylinder head and intake manifold contact face Rubber gasket between cylinder heads and valve covers Two-layer embossed metal gasket between cylinder heads and exhaust manifoldMultilayer embossed metal gasket between cylinder heads and crankcaseLiquid gasket between crankcase upper section and bearing supportCoated embossed metal gasket S248_148 Liquid gasket between oil sump upper section and lower section between oil sump upper section and bearing support52Liquid gaskets Application of the liquid gasket sealant is CNCcontrolled in order to ensure a constant sealant supply. The liquid gasket between the lower timing case cover and the upper timing case cover is applied according to a different principle. In this case, the parts are first bolted, then the sealant is injected into the groove in the upper timing case cover via screw nipples (Sealing Injection System). When enough liquid sealant has been injected, the excess sealant is discharged from the openings on the end of the timing case cover. The screw nipples remain in the housing after injecting the sealant. However, they have to be replaced when repairing the gasket.Screw nippleScrew nipple for liquid gasket installation Upper timing case cover S248_152S248_151 Groove for sealantUpper timing case cover S248_140 Lower timing case cover (sealing flange) Outlet S248_153 (covering part)53ServiceEngine timing overviewIf it is necessary to disassemble the cylinder heads, the engine timing must be reset. These are the important markers when the piston of the first cylinder is at top dead centre.Put copper coloured chain link on arrow of bank IIS248_192Put copper coloured chain link on arrow of bank IIS248_144Adjust exhaust camshaft to advanceAdjust inlet camshaft to retardBank IIPosition the marker on the vibration damper on the housing joint: piston in 1st cylinder at top dead centre.Insert the mandrel for fixing the crankshaft into the threaded hole in the housing: piston in 1st cylinder at top dead centre.S248_191S248_19054Insert camshaft rule for aligning the camshafts.Place the copper coloured chain link on the marked tooth of the intermediate shaft and the bore hole in the housing Place copper coloured chain link on arrow of bank IS248_193Place copper coloured chain link on arrow of bank IIInlet camshaft advance adjustmentExhaust camshaft retard adjustmentBank IWhen placing on the lower timing chain copper, set the coloured chain link on the marked tooth and the marked tooth on the housing joint: piston in 1st cylinder at top dead centre.S248_178For a description of the exact procedure for setting the engine timing, please refer to the relevant Workshop Manual.S248_194 Normal tooth Marked tooth55ServiceSpecial toolsDesignation Camshaft alignment rule Tool No..: T 10068ToolUse For aligning the camshafts when setting the engine timingS248_187Mandrel Tool No.: 3242For locating the crankshaftS248_188Engine and transmission holder Tool No.: VAS 6095For removing and installing engines and gearboxesS248_19556Notes57Test your knowledge1. a. b. c. The cylinders in the W engine are arranged according to the follow principle: two in-line engines arranged in tandem two in-line engines arranged side by side two V engines arranged side by side2. The W engine has left and right cylinder banks. They are aligned at an angle of: a. b. c. d. 15° 60° 72° 120°3. a. b. c. d. e.The maximum possible number of cylinders in an engine based on the W engine principle is: W18. W16. W12. W10. W8.4. What does splitpin mean? a. b. c. an offset amounting to 12.5 mm. a crank pin offset which facilitates a regular firing interval. The centre of the crankshaft (fulcrum) is located below the point of intersection of the intersecting centres of the cylinders.585. a.Why does the W8 engine have a balancing shaft? to prevent rotary vibrations being transmitted from the crankshaft to the gearbox to compensate for torsional vibration to compensate for forces of inertia to determine the engine speedb. c. d.6. A pulse sensor wheel is used to determine the engine speed a. b. c. it is press-fitted onto the crankshaft. it is integrated in the two-mass flywheel. it is located on the gear side of the balancing shafts7.Which ducts are routed through the cylinder heads?1.) __________________________________________________________________________ 2.) __________________________________________________________________________ 3.) __________________________________________________________________________8. How are the camshafts adjusted? a. b. c. pneumatically hydraulically mechanically59Test your knowledge9. The adjustment ranges of the camshaft adjuster between the inlet camshaft and the exhaust camshaft are different. The exhaust camshaft of the W8 engine can be adjusted continuously! only be adjusted to the advance or retard position!a. b.10. The following units are driven by the pulley drive: a. b. c. d. e. the coolant pump the alternator the fuel pump the power-steering pump the air-conditioning compressor11. Which of the following statements is true? a. b. c. the W8 engine has a wet-sump lubrication system. the W12 engine for VW models has a dry-sump lubrication system. the W12 engine for VW models has a wet-sump lubrication system.12. Characteristic maps which allow the desired engine temperature to be reached in accor dance with theengine's operating requirements are stored in the engine control unit. Which of the following statements is applicable? a. b. c. There is only one temperature sensor in the cooling circuit, and it is located at the radiator outlet. There are two temperature sensors in the cooling circuit. there is only one temperature sensor in the cooling circuit, and it is located at the engine block outlet.6013. Which of the following statements is true? a. The coolant flows through the cylinder heads from the exhaust end to the intake end. This ensures very good temperature equalisation as well as effective cooling of the outlet webs and spark plugs.b.Coolant flows through the cylinder heads from the intake side to the exhaust side. This ensures very good temperature equalisation as well as effective cooling of the outlet webs andspark plugs.14. A new liquid sealing method is used to seal the upper timing case cover. The liquid gasket is injected through screw nipples. a. b. c. The screw nipples have to be replaced when repairing the gasket. The screw nipple can be reused any number of times. The screw nipples must be unscrewed after repairing the gasket.61Notes6263Solutions 1.) c 2.) c 3.) b, c, d, e 4.) b 5.) c 6.) b 7.) 1 Oil ducts 2 Coolant ducts 3 Secondary air ducts 8.) b 9.) b 10.) a, b, d, e 11.) a, c 12.) b 13.) a 14.) a248For internal use only © VOLKSWAGEN AG, Wolfsburg All rights reserved. Technical specifications subject to change without notice. 140.2810.67.20 Technical status: 08/01❀ This paper is produced fromnon-chlorine-bleached pulp.