TECHNICAL DOCUMENTATION

SSP 255 The 2,0 l R4 and the 3,0 l V6 engines

PDFEN40 pages2 MB
SSP 255 The 2,0 l R4 and the 3,0 l V6 engines - PDF cover

This PDF is currently unavailable.

Read document text
255Service.The 2.0 l R4 and the 3.0 l V6 engines Self-study programme 255For internal use only. 2 ContentsPage The 2.0 l-5V engineOverview – Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Balancer shaft module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 New cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Map-controlled cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Functional diagram for the 2.0 l-5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12The 3.0 l-5V engineOverview – Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crankcase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Balancer shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air intake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vacuum system overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exhaust system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensors/Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional diagram for the 3.0 l-5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 15 17 18 20 27 29 32 33 33 34 36New The self-study programme will provide you with information on design and functions. The self-study programme is not intended as a workshop manual. For maintenance and repair work it is essential that you refer to the current technical literature.Important: Note3 OverviewThe 2.0 l-5V engineTorque [Nm]SSP254_038Engine speed in rpmSSP254_060Technical data Engine code: Capacity: Bore: Stroke: Compression: Power output: Torque: Valve timing: Adjustment range Inlet camshaft: Engine management: Exhaust emissions class: Capacities: 10.3 : 1 Consumption: 96 kW (130 PS) 195 Nm at 3300 rpm bucket tappets with hydraulic valve lifters 5 per cylinder Weight: inlet opens 26° CA after TDC inlet closes 48° CA after BDC exhaust opens 32° CA before BDC exhaust closes 8° CA before TDC Acceleration from 0 to 100 km/h: Fuel: Valves: 9.9 s 4-star petrol, unleaded, 95 (91) RON 129 kg urban 11.4 l/100 km non-urban 5.9 l/100 km average 7.9 l/100 kmALT 1984 cm3 82.5 mm 92.8 mm42° CA (Crank Angle) ME 7.5EU 4 Engine oil (incl. filter) 4.2 lValve timing:4Power output [kW] EngineEngine blockThe engine block is made of aluminium alloy and, with a cylinder spacing of 88 mm and a length of only 460 mm, is the most compact unit in its class. For reasons of rigidity, the aluminium crankcase is designed as a “closed deck” construction.“open deck” means that the cylinder liners are installed with only small cast connections to the block. “closed deck” means that the cylinder linings are cast in one piece with the block.SSP255_004In order to ensure sufficient cooling between the cylinder liners, cooling ribs of 0.8 mm in width are provided.The oil return ducts on the inlet side are arranged such that the oil (dark green) is guided to the sump via a collection channel from the cylinder head through an inlet pipe below the oil level. On the exhaust side, the oil (light green) runs down the crankcase wall due to the angle of the engine in the installation position.SSP255_0535 EngineBalancer shaft moduleBalancing weights Ratio 1 : 2Drive from CrankshaftSSP255_005 Oil pumpThis module is intended to compensate the inertia forces that occur and hence reduce drive unit vibration.To further improve running smoothness of the 4-cylinder engine, two counter-rotating balancer shafts rotating at double crankshaft speed are integrated in an oil pump/balancer shaft module. The drive chain sprocket on the balancer shaft unit is driven via a three-point chain drive (crankshaft/balancer shaft/oil pump).The initial ratio of the crankshaft to the drive shaft on the balancer shaft module is 1 : 1. The stepping up to double crankshaft speed takes place in the 1st drive stage via a helical gear pair. The balancing weights are integrated into the gears of the 2nd stage. Here, the rotational direction of the second balancer shaft is reversed. The second degree inertia forces are 100 % compensated.6 New cylinder headThe cylinder head is designed as a laddertype frame for better rigidity and optimum acoustics (see diagram SSP255_018 on page 20). This means that the camshafts are installed in the cylinder head with greater bending resistance. Individual bearingcaps are not required. The exhaustcamshaft is driven by the toothed belt. The inlet camshaft is driven by a roller chain from the exhaust camshaft. The roller chain is tensioned via a hydraulic chain tensioner.SSP255_006However, the hydraulic chain tensioner is not responsible for the camshaft timing control.The inlet camshaft is continuously adjusted by a hydraulic swivelling motor. In order to achieve optimum torque characteristics, the inlet camshaft can be map-adjusted by a crank angle of up to 42°.The camshaft timing control function is described for the 3.0 l-V6-5V engine.SSP255_0077 EngineInlet manifold changeover systemThe power and torque characteristics are realised with the aid of a two-stage inlet manifold changeover system, whereby the changeover point from short to long intake path occurs between 2000-3700 rpm at 65 % load. The intake path is selected via a selector cylinder which separates the individual intake ducts via elastic sealing rings and strips. The switch between torque and power positions is electro-pneumatic (load/torque/ temperature dependent).Selector cylinderVacuum reservoirTorque positionPower positionSSP255_0088 Exhaust emissions controlA staged metal catalytic converter is installed close to the engine to allow it to reach operating temperature rapidly after the engine has been started. A fast start is also facilitated by the exhaust manifold which is manufactured in an internal high pressure moulding process (IHM) and has very low heat capacity. As a result, it absorbs less heat energy.SSP255_009The staged catalytic converter is divided into two different metal parts, with a cell density of 400 cpsi and a length of 50.8 mm in the first stage and a cell density of 500 cpsi and a length of 110 mm in the second stage.For more information on the internal high pressure moulding process, please see SSP 239 – Audi A2, Body.Vacuum systemConstantly increasing load requirements (wider opened throttle valve) in some operating statuses, e.g. when the catalytic converter is warming up while the engine is idling after starting up, result in a reduction of the vacuum generated by the engine. To avoid losing any braking efficiency, an electric vacuum pump is used to assist braking in vehicles with automatic gearbox.For further explanations, please see the 3.0 l-V6 engine on page 30.9 EngineMap-controlled coolingThe 2.0 l engine is equipped with map-controlled coolant temperature control. Compared to conventional thermostat-based systems, this improves the thermodynamic efficiency of the engine while also optimising torque. Thermostat-controlled systems work according to the on/off principle. This means: when the coolant reaches a temperature of approx. 100 °C, the wax-filled thermostat activates the large coolant circuit independently of engine load status. This setting is also the standard setting for all loads, except full throttle.SSP255_010At full throttle, current is applied to a thermal pellet in the expanding element and heats up the wax, thereby opening the thermostat wider. This reduces the coolant inlet temperature to 75 – 80 °C. A high coolant temperature of approx. 100 – 105 °C improves thermodynamic efficiency and minimises the friction caused to the engine by the increasing oil temperature. Reducing coolant temperature at full throttle makes the combustion chambers cooler. Cooler combustion chambers allow an earlier ignition point and so provide the desired gain in torque.SSP255_011For more information, please see SSP 222, 1.6 l engine.10 Notes11 EngineFunctional diagram for the 2.0 l-5VF F36 F47 F265 G2 G6 G28 G39 G40 G42 G61 G62 G66 G70 G79 G82 G130 G185 G186 G187 G188 G294 J17 J138 J271 J299 J569 M N N30 N31 N32 N33 N80 N128 N158 N163 N205 N239 Brake light switch Clutch pedal switch Brake pedal switch for cruise control system Thermostat for map-controlled engine cooling Coolant temperature sender Fuel pump Engine speed sender Lambda probe Hall sender Intake air temperature sender Knock sensor 1 Coolant temperature sender Knock sensor 2 Air mass meter Accelerator position sender Coolant temperature sender for engine outlet Lambda probe downstream of catalytic converter Accelerator position sender 2 Throttle valve drive (electronic throttle control) Angle sender 1 for throttle valve drive (electronic throttle control) Angle sender 2 for throttle valve drive (electronic throttle control) Pressure sensor for brake servo Fuel pump relay Control unit for radiator fan run-on Power supply relay for Motronic Secondary air pump relay Brake servo relay Lamp Ignition coil Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4 Solenoid valve 1 for activated charcoal filter system Ignition coil 2 Ignition coil 3 Ignition coil 4 Valve 1 for camshaft timing control Intake manifold flap changeover valve S V101 V192 Z19 Z29 Fuses Motor for secondary air pump Vacuum pump for brake Heater for lambda probe Heater for lambda probe 1, downstream of catalytic converterColour coding = Input signal = Output signal = Positive power supply = Earth = CAN BUS = Bi-directional Auxiliary signals K diagnostic connection 1 2 Crash signal Cruise Control System ON/OFF PWM signal to radiator fan TD signal (V30 automatic gearbox only) Databus drive Databus information3 45 6Y Z12{XConnection within the functional diagram 3015 YX J17 J271 J299 J569S43 15AS7 10A30aSW 40AS9 15AS32 20AS34 15AS29 20AX S28 20A F F36MY SW 15AZ15ZJ138MMG6F47MN205F265V101V192N30N31N32N33N239N80NP QN128P QN158P QN163P QJ220-++ P G42 G82 G2/G62 G294+G28 G66 G61+MM G187 G188 G185 G79 G70 Z29λG130λZ19 G39G40G186123456Z3131inout OverviewThe 3.0 l-5V engineSSP254_030Engine speed in rpmSSP254_061Technical data Engine code: Capacity: Bore: Stroke: Compression: Power output: Torque: Valve timing: ASN 2976 cm3 82.5 mm Capacities: 92.8 mm Consumption: 10.5 : 1 162 kW (220 PS) 300 Nm at 3200 rpm bucket tappets with hydraulic valve lifters 5 per cylinder inlet opens inlet closes exhaust opens exhaust closes Acceleration from 0 to 100 km/h: Fuel: 6.9 s Super Plus unleaded 98 (95) RON 165 kg urban 13.7 l/100 km non-urban 7.1 l/100 km average 9.5 l/100 km Engine oil (incl. filter) 6.3 l Engine management: Exhaust emissions class: ME 7.1.1EU 4Valves: Valve timing:Weight: 20° CA after TDC 50° CA after BDC 47° CA before BDC 17° CA before TDC14Power output [kW]Torque [Nm] EngineCrankcaseIn terms of lower weight, higher output and higher maximum engine speed, all the experience gained with V8 aluminium crankcases points to only one type of aluminium crankcase, offering the best characteristics in relation to strength, durability and oil system optimisation. The aluminium crankcase with cast iron cylinder liners is manufactured using the Cosworth casting process.SSP255_012The oil returning from the cylinder heads is guided along the bulkhead walls and through the oil baffle plate below the dynamic oil level into the sump. This considerably reduces the gas content of the oil caused by the crank drive.Oil return Bulkhead wallCollection channelOil baffle (Baffle plate)SSP245_04415 EngineCrank assemblyThe crankshaft is mounted on 4 bearings with split crank pins (30° offset), allowing a uniform firing sequence of 120°.SSP255_013Lightweight smooth shaft pistons with a curved box form and closely arranged piston pin eyes have been adapted to the trapezoidal conrod. The piston pins are shorter and have a smaller diameter, allowing a reduction in the weight of the masses moving back and forth (oscillating). The pistons are cooled by oil spray nozzles in the crankcase. The piston shaft has a wearresistant ferroprint running surface which is produced by a screen printing process.SSP255_01416 Balancer shaftThe free inertia forces in V6 engines can be completely compensated with a cylinder angle of 90°.The free moments of inertia (1st degree) cannot be completely eliminated without additional measures and some comfort is lost.To keep up with growing comfort requirements, a balancer shaft has been installed below the crankcase.The oil pump and the balancer shaft are combined into a single aluminium module. The shaft is positioned on plain bearing shells and is supplied with oil from the rear fixed bearing. The front free bearing is lubricated via a bore in the shaft.SSP255_015Drive is provided by a roller chain from the crankshaft to the oil pump shaft. The gear driving the balancer shaft is mounted in front of the chain sprocket, and meshes with the gear on the balancer shaft with a transmission ratio of 1 : 1. Thus the balancer shaft runs counter to the direction of engine rotation. The reversal of rotation direction required to compensate for the “first degree” moment of inertia is realised by the spur pinion.Chain sprocketSSP255_016 17 EngineOil circuitCylinder bank 1Cylinder bank 2Camshaft timing control ExhaustInletOil retention valvesInletCamshaft timing control ExhaustSpray nozzle valveNon-return valve Bypassvalve Oil filter Crankshaft and conrod supports Chain tensionerOil coolerSSP255_026Filter elementOil pressure safety valveOil pressure control valve Oil pressure pumpBalancer shaftNon-pressurised oil circuit Pressurised oil circuit18 Crankcase ventilationLabyrinth separatorto crankcasebreatherEntry of blow-by gasesSSP255_027Similarly to the current V6 engines, the oil from the V-chamber cover and the two cylinder head covers is fed into the oil circuit and vented via the integrated labyrinth separator. The blow-by gases for combustion are introduced directly into the intake manifold and not upstream of the throttle valve. A differential pressure controlled diaphragm valve regulates the required vacuum level for the crankcase.ASSP255_052 A differential pressure controlled diaphragm valve 19 EngineCylinder headFor reasons concerning rigidity and acoustics, the camshaft supports have been changed from single bearing caps to a one-piece pressure-cast aluminium ladder-type frame.The front faces and the bearings for the ladder-type frame are machined after assembly. This means that plane sealing surfaces between cylinder head cover and ladder frame and the attached module housings are designed as axial sealing surfaces.The cylinder head features a Tumble inlet duct (bi-turbo) in order to achieve a high internal exhaust gas recirculation rate even in the low rpm and load range.SSP255_017The cylinder head cover with a welded bulkhead provides better acoustics and a more rigid connection. This bulkhead with integrated labyrinth separators is used as a cover for the extended ventilation area and as an additional oil separator for the vent gases. The oil separator volume has been increased.Pressure oil supply Inlet OutletThanks to the ladder frame design, the pressure oil required for continuous camshaft timing control is supplied by an oil supply unit bolted to the front face.The ladder frame has bores on both sides to supply pressure oil. This allows the cylinder head to be used on the left or right cylinder bank by rotating the cylinder head through 180°.SSP255_01820 Cylinder bank 1Cylinder bank 2SSP255_050 Exhaust swivelling motor (with damper) Inlet swivelling motor Inlet swivelling motorSSP255_051 Exhaust swivelling motor (without damper)The central, low-throttle i.e. block-oil pressure driven oil supply was a prerequisite for the use of the oil pressure driven camshaft timing control. The four camshafts are driven directly by the toothed belt. Thermodynamic tests indicated an adjustment range of up to 42° crank angle on the inlet side and up to 22° on the exhaust side. Adjustment is made by four hydraulic swivelling motors, and occurs on the – inlet side continuously from 20° CA after TDC (retard) up to 22° CA before TDC (advance) and on the – exhaust side with on/off controls (advance/retard). The inlet swivelling motors of cylinder banks 1 and 2 are in the rest position (no pressure) in the retard position. The exhaust swivelling motors of cylinder banks 1 and 2 are in the rest position in the advance setting.21 EngineContinuous camshaft timing controlFigure shows standard setting: 4/2-way valve Differential pressure pins Intake advance positionRotorPressure oil-feed Stator SSP255_019 Intake retard positionThe swivelling motor adjusters are supplied by the engine oil pump via the pressure line in the cylinder head. Adjustment of the inlet camshafts is made by means of two pulse-width modulated 4/2 way proportional valves. In contrast, adjustment of the exhaust camshafts is made via two black-white 4/2 way solenoid valves. The solenoid valves are actuated by the engine control unit.The maximum valve overlap is set at 1900 rpm to achieve the highest possible torque or to perform internal exhaust gas recirculation.22 Oil supply module4/2 solenoid valvesPressure oil feed Oil return duct SSP255_020 Oil ring ductReturn holes for swivelling motorThe pressure oil required for adjustment is fed through the camshaft to the adjuster via an oil ring duct. The inner ring (rotor) of the swivelling motor is connected to the camshaft. The outer ring (stator) is connected securely to the toothed belt sprocket. The camshaft is adjusted in relation to the crankshaft by filling the working area between rotor and stator with oil.In order to move to each position (0 - 42°) between stops, the 4/2 way proportional valve is regulated by the engine control unit. Regulation depends on speed, load and coolant temperature.23 EngineInlet camshaft driving control (no pressure) The 4/2 way valve has no power supply. The spring-loaded differential pressure pin locks into a bore, thus preventing the camshaft from being adjusted during the start procedure. It is locked into position by a selective return to the retard position when the engine is switched off. The exhaust camshaft timing control is in the advance position.Camshaft timing control (rotor) with connection to camshaftDifferential pressure pins (locked)StatorToothed belt ringCamshaft sprocket SSP255_021Inlet camshaft timing control in retard position (Engine running) The springloaded differential pressure pin is unlocked by the engine oil pressure.Working area BDifferential pressure pins (unlocked)The solenoid valve opens the access to the working area B and holds the rotor in working area A. The inlet camshaft is in the retard position. In the idling range, there is as little valve overlap as possible. This results in a low proportion of exhaust gas and therefore smooth and stable idling. The exhaust camshaft is in advance position (solenoid valve off).Rotor in working area ASSP255_02224 Inlet camshaft in control position The solenoid valve is actuated by the engine control unit with a pulse-width modulated signal. The solenoid valve piston is set such that both working areas are under oil pressure. The rotor, and as a result the camshaft, moves in the direction of advance or retard in accordance with the oil pressure conditions in working areas A and B. The pulse-width modulated actuation allows continuously variable adjustment of the camshaft. The valve opening times are adjusted to the charge changing process depending on engine speed and load.Working area A Working area BSSP255_023Inlet camshafts in advance position The oil pressure enters working area A via the solenoid valve pistons; the rotor moves in the direction of working area B. The exhaust camshaft is in the retard position (solenoid valve on). As much overlap as possible results in internal exhaust gas recirculation and optimum torque usage.SSP255_02425 EngineToothed belt driveCylinder bank 1Cylinder bank 2Exhaust swivelling motor with vibration damperhydraulically damped tensioning rollerSSP255_049The drive of the inlet and exhaust camshafts with four camshaft timing controls required a hydraulically damped toothed belt tensioning system. This was developed in conjunction with a vibration damper on the exhaust camshaft of the right cylinder bank and the latest generation of toothed belt.The toothed belt is installed using several special tools: – T40026 – 3299/1 – T40030 – T40028 Crankshaft clamping bolt Clawed tensioning element (ribbed belt) Camshaft setting gauge Camshaft timing control socket insertThe exhaust swivelling motor of cylinder bank 1 has a damper to compensate for combustion pulses.26 Air intakeThe previous air filter housing had to be re-designed because of the new headlight housing. The air filter housing is now narrower with the same air volume as its predecessor, but the air intake has been increased by around 50 %. Air is taken in through the front end and the wheel housing in order to reduce the intake speed. The intake noise is damped by a Helmholtz resonator. This has a volume of 250 cm3 and it opens directly into the most effective part of the air scoop. This dampens excessive noise at speeds between 4000 and 5000 rpm.Outside air intake Front end Air filterWheel housing intakeAirmass meter Ribbed tubeAir scoopHelmholtz resonatorSSP255_028Electronic throttle positionerIntake moduleThe design provides two intake manifold lengths by means of a selector cylinder.SSP255_03127 EngineSelector cylinder Sealing ringSealing stripSSP255_030The selector element is a plastic rotary port running on 2 bearings which is activated by two vacuum units (in order to achieve equal distribution of the load on the cylinder). It is returned to the initial position via a spring. Pre-tensioned sealing rings on the cylinder for each duct provide significantly improved leakage values compared to earlier designs. This contributes to the development of more than 300 Nm of torque.The spring-loaded connection of the two sealing strips to a sealing element ensures an optimum seal at any load and any tolerance.Torque settingPower settingSSP255_029The selector cylinder enables 2-stage longitudinal swivel-tube switching. In the torque position, the duct length is 640 mm, in the power position it is 287 mm. The switching point from long to short is at approx. 4200 rpm.28 Vacuum system overviewN239AACBN80D E N112 FG H H SSP255_032AVacuum units for register intake manifold changeover Vacuum reservoirF GSuction jet pump Brake servo Combi valve for secondary air Solenoid valve for activated charcoal filter Secondary air inlet valve Intake manifold flap changeover valve29B CH Fuel rail with pressure control valve Activated charcoal filter N112 E Non-return valve N239 N80D EngineVacuum system (vehicles with automatic gearbox)Motronic control unit J220Differential pressure sensor G294 Brake servoNon-return valveAuxiliary consumersExhauster with flanged electric motorSSP255_033The relay is activated by the engine control Constantly increasing load requirements (wider opened throttle valve) in some operating unit when a drop in the vacuum in the brake servo is detected. statuses, e. g. when the catalytic converter is warming up while the engine is idling after starting up, result in a reduction of the vacuum generated by the engine. To avoid losing any braking efficiency, an electric vacuum pump is used to assist braking in vehicles with automatic gearbox.30 Activation of the vacuum pump The vacuum pump is activated under the following conditions: • PBS* Pswitch-on pressure approx. 500 mbar The vacuum pump is deactivated under these conditions: • PBS* Pswitch-off pressure approx. 300 mbarP BS* P switch-on pressurePswitch-off pressure Time [t]onPump statusoffSSP255_034Altitude correction The altitude value calculated in the control unit is compared with the pressure of the brake servo sender G294. The electric vacuum pump is activated if there is a relevant difference in pressure. Self-diagnosis Final control diagnosis: the vacuum pump should run for approx. 10 seconds. Measured value block: Channel 08Byte 1 Brake actuated/ brake not actuatedByte 2 Voltage supply (V)Byte 3 pump on/ pump offByte 4 brake servo pressure (mbar)*Brake servo31 EngineExhaust systemAn air-gap-insulated manifold in monocoque design has been developed for the 3.0 l engine. This manifold consists of three separate internal pipes, so-called inliners, for conducting the gas, and a temperature-insulated outer shell.The inliners, which are manufactured using the IHM (internal high pressure moulding) process owing to their compact geometry, join into a “3 in 1” outlet flange.SSP255_035For more information on the IHM process, please see SSP 239 – Audi A2, Body.Cylinder 5This joining of the inliners enables a precise inflow to the primary catalytic converters, allowing the catalytic converter to start up quickly thanks to an optimisation of the pipe geometry and modification of the monolith. The engine has 2 ceramic primary catalytic converters installed close to the engine with a cell density of 600 cpsi each and a coating of three precious metals. This achieves a quick start-up of the catalytic converter. The two main catalytic converters in the underbody area with a cell density of 400 cpsi and coated in three precious metals ensure long-term stability of exhaust emissions at optimum exhaust back pressure.Cylinder 4 Cylinder 6SSP255_036The three precious metals in the coating are: – platinum – palladium – rhodiumcpsi = cells per square inch 600 cpsi = 600 cells per 6.452 cm232 Engine managementThe ME 7.1.1 engine control unit is a torque driven electronic throttle system with constant lambda control, two broadband probes upstream of the catalytic converter and two two-point probes downstream of the catalytic converter. The focus during development was fillinglevel monitoring and torque co-ordination. Adjusting four camshafts, two of them continuously, demands a considerable amount of computing capacity and speed. In order to achieve this computing performance, the engine control unit has a 32 MHz processor. It is imperative that both cylinder banks are synchronised. Because of component tolerances it is possible that the inlet camshaft timing controls perform adjustments at different speeds, especially when the oil is cold or extremely hot. For this reason, a bank equaliser has been created with four Hall senders for the first time on a two-bank system with a control unit. Equalisation is performed according to the master-slave principle. The retarded camshaft timing control on one cylinder bank (master) determines the nominal values for the other cylinder bank (slave). This ensures correct pre-control of the fuel quantity and ignition for dynamic processes under any road conditions.Sensors/ActuatorsPhase sensors 1 - 2 - 3 - 4 Four phase sensors are required to monitor the individual positions of the camshafts in relation to the crankshaft. If one or more sensors fail, the swivelling motors are mechanically locked by the differential pressure pins. The engine will still start despite loss of signal, permitting emergency running.SSP255_03733 EngineOverview of systemSensorsHot film air mass meter G70Engine speed sender G28Control unit for Motronic J220Hall sender G40 Hall sender 2 G163 Hall sender 3 G300 Hall sender 4 G301 Lambda probe upstream of catalytic converter G39 Lambda probe downstream of catalytic converter G130 Lambda probe 2 G108 Lambda probe 2 downstream of catalytic converter G131 Throttle valve control unit J338 with throttle valve drive G186 (electronic throttle control) Angle sender 1 for throttle valve drive G187 Angle sender 2 for throttle valve drive G188 Coolant temperature sender G2 and G62 Knock sensor 1 G61 (Bank 1) and Knock sensor 2 G66 (Bank 2) Sender for steering angle G85Pressure sensor for brake servo G294Control unit for ESP J104Pedal value sender/accelerator pedal module with accelerator position sender (1) G79 and accelerator position sender (2) G185Automatic gearbox control unit J217Brake light switch F and brake pedal switch F47 Combination processor in dash panel insert J285Clutch pedal switch F36 Auxiliary signals – Air conditioner ready – air conditioning compressor bi-directional – Crash signal – CCS switch 34Operation and display unit for air conditioner E87 ActuatorsFuel pump relay J17 and fuel pump G6Injectors N30, N31, N32Injectors N33, N83, N84Ignition coils N (Cyl. 1), N128 (Cyl. 2), N158 (Cyl. 3.)Ignition coils N163 (Cyl. 4), N164 (Cyl. 5), N189 (Cyl. 6.)Vacuum pump with electric motor Solenoid valve for activated charcoal filter N80Intake manifold flap changeover valve N239Secondary air pump relay J299 and secondary air pump motor V101Secondary air inlet valve N112 Throttle valve control unit J338 with throttle valve drive G186 (electronic throttle control)Valve for camshaft adjustment N205 (Bank 1) and N208 (Bank 2) Control unit for Lambda probe heater J208 Heater for lambda probe Z19 (Bank 1) Heater for lambda probe Z28 (Bank 2) Heater for lambda probe 1, downstream of catalytic converter Z29 Heater for lambda probe 2, downstream of catalytic converter Z30 Auxiliary signals – Air conditioning compressor SSP255_046 35 EngineFunctional diagram for the 3.0 l-5VF F36 F47 G2 G6 G28 G39 G40 G61 G62 G66 G70 G79 G82 G108 G130 G131 G163 G185 G186 G187 G188 G294 G300 G301 J17 J138 J220 J271 J299 J496 J569 M N N30 N31 N32 N33 N80 N83 N84 N112 N12836Y Z{Brake light switch Clutch pedal switch Brake pedal switch for cruise control system Coolant temperature sender Fuel pump Engine speed sender Lambda probe Hall sender Knock sensor 1 Coolant temperature sender Knock sensor 2 Air mass meter Accelerator position sender Coolant temperature sender for engine outlet Lambda probe 2 Lambda probe downstream of catalytic converter Lambda probe 2 downstream of catalytic converter Hall sender 2 Accelerator position sender 2 Throttle valve drive (electronic throttle control) Angle sender 1 for throttle valve drive (electronic throttle control) Angle sender 2 for throttle valve drive (electronic throttle control) Pressure sensor for brake servo Hall sender 3 Hall sender 4 Fuel pump relay Control unit for radiator fan run-on Control unit for Motronic Power supply relay for Motronic Secondary air pump relay Auxiliary coolant pump relay Brake servo relay Lamps Ignition coil Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4 Solenoid valve 1 for activated charcoal filter system Injector, cylinder 5 Injector, cylinder 6 Secondary air inlet valve Ignition coil 2N158 N163 N164 N189 N205 N208 N239 S V51 V101 V144 V192 Z19 Z28 Z29 Z30Ignition coil 3 Ignition coil 4 Ignition coil 5 Ignition coil 6 Valve 1 for camshaft adjustment Valve 2 for camshaft adjustment Intake manifold flap changeover valve Fuses Pump for coolant run-on Motor for secondary air pump Diagnosis pump for fuel system Vacuum pump for brake Heater for lambda probe Heater for lambda probe 2 Heater for lambda probe 1, downstream of catalytic converter Heater for lambda probe 2, downstream of catalytic converterColour coding = Input signal = Output signal = Positive power supply = Earth = CAN BUS = Bi-directional Auxiliary signals K diagnostic connection 1 2 3 4 DF signal Crash signal PWM signal to radiator fan TD signal (V30 automatic gearbox only) Databus drive Databus information5 6 XConnection within the functional diagram 3015 YX J17 J271 J496 J299 J569S43 15AS7 10A30aSW 40AS9 15AS32 20AS29 20AX S28 20A F F36MY SW 15AZ15ZJ138MMMG6F47MN205N208V51V101V192N30N31N32N33N83N84NP QN128P QN158P QN163P QN164P QN169P QJ220-++ P G82 G2/G62 G294++++G28 G66 G61J338+MMλG70 Z29 G130λZ19 G39 Z30λG131λZ28 G108N112G40 G163 G300 G301 G186 G187 G188 G185 G79 V144N80N239 1 2 3 4 5 6Z3131inout Notes38 Notes39 All rights reserved, including the right to make technical changes. AUDI AG Dept. I/VK-5 D-85045 Ingolstadt Fax 0841/89-36367 040.2810.74.20 Technical status 03/01 Printed in Germany255