TECHNICAL DOCUMENTATION

SSP 282 AUDI A8 ´03 – Technical Features

PDFEN96 pages5 MB
SSP 282 AUDI A8 ´03 – Technical Features - PDF cover

This PDF is currently unavailable.

Read document text
282Service.AUDI A8 ´03 - Technical FeaturesSelf Study Programme 282For internal use only Complete vehicle informationThe design and operation of the Audi A8 ´03 are described in the following Self Study Programmes:SSP 283 – 6-speed automatic gearbox 09E in the Audi A8 '03 - Part 1 SSP 284 – 6-speed automatic gearbox 09E in the Audi A8 '03 - Part 2 SSP 285 – Running gear in the Audi A8 '03 SSP 286 – New data bus systems - LIN, MOST, BluetoothTM SSP 287 – Audi A8 '03 - Electrical components SSP 288 – Audi A8 '03 - Distributed functions SSP 289 – Adaptive cruise control in the Audi A8 '03 SSP 292 – Adaptive air suspension in the Audi A8 '03 SSP 293 – Audi A8 '03 - InfotainmentOther helpful information on the Audi A8 ´03 can be found on the adjacent CD ROMs.Electrical system CAN data bus 2 ContentsPage Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Passenger ProtectionSystem layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Safety systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Engine, MechanicsTechnical data of V8 4.2 l 5V engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical data of V8 3.7 l 5V engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrohydraulic torque reaction support . . . . . . . . . . . . . . . . . . . . . . . . . Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatically controlled starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 25 30 32 33 34 41Gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Running GearFront axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-level air suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adaptive cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 50 51 52 53 54Electrical SystemBus topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Convenience and security electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Lighting system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Heating/Air ConditionerDesign and operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blower unit/air routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block diagram for front air conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . Block diagram for rear air conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 74 76 80 86 88The Self Study Programme contains information on design features and functions. The Self Study Programme is not intended as a Workshop Manual. Values given are only intended to help explain the subject matter and relate to the software version applicable at the time of SSP compilation. Use should always be made of the latest technical publications when performing maintenance and repair work.NewAttention Note3 IntroductionIntroductionThe new Audi A8 is designed to replace its predecessor of the same name which achieved a total production figure of 105,092 since its introduction in June 1994. This was the first standard saloon with aluminium body and epitomised a new philosophy in the luxury vehicle sector. The weight-saving Audi Space Frame ASF represented a major breakthrough in terms of enhanced vehicle dynamics, whilst at the same time solving the problem of increasing weight.Active head restraints for front seats Convenience/infotainment control via multimedia interface (MMI)This body concept was further perfected in the Audi A2 and the design of the Audi A8 ´03 reflects the experience gained from both projects. The aim when developing the Audi A8 ´03 was not merely to surpass its predecessor in terms of technical features and details.3.7 or 4.2 l V8 engine with intake manifold changeover functionAdaptive cruise control (ACC) with radar sensor in front bumper4Headlight with adaptive light function As the Audi flagship, the new Audi A8 is intended to symbolise the product identity of the next Audi generation.An uncompromising sporty character, clearcut design, innovative technological systems and the highest possible quality level combine to provide an unforgettable driving experience. In other words:Automatic boot lid opening and closing function (optional)Audi at its proverbial best.LED-type tail lights4-level air suspensionElectric parking brake"Advanced Key" entry and start authorisation system SSP282_0256-speed automatic gearbox 09E 5 BodyBrief outline14449761629 18941615 20289711252944 50511136SSP282_026Kerb weight Turning circle Tank capacity61,780 kg 12 m approx. 90 litresGross weight Luggage compartment volume Drag coefficient2,380 kg approx. 500 l 0.27 Cd714 Body The Audi A8 ´03 sets new standards in its class by combining lightweight construction with outstanding stability. This is achieved through the use of innovative Audi Space Frame technology for the body design of the Audi A8. The technical progress reflected by the unique body concept stems from the consistent implementation of experience gained from the aluminium Audi A8 and A2 models. Based on the findings obtained from these vehicles, it was possible to further reduce the number of body components and significantly increase the level of automation in the production process as compared to the Audi A8 predecessor model.SSP282_027The static torsional rigidity of the new Audi A8 body is 60 % higher than that of the previous Audi A8 body. A crucial contribution is made to the increased rigidity level by the advanced Audi Space Frame structure.Characteristic features of the new structure: – Large castings with numerous integrated functions and a high degree of joint strength – IHF* sections – optimum cross sections at all locations, for example at side of roof frame – Sheet metal panels with high levels of local rigidity thanks to the use of special technologies designed to achieve differing functional cross sections and structures*IHF = Internal high-pressure forming7 BodyA-pillar The A-pillar is made of two cast shells connected by rivets and welds. The shells enclose the sill panel at the bottom and the continuous roof frame at the top.SSP282_029Sill panel Use is made for the sill panel of a 3-piece extruded section. The extruded section must be replaced in the event of sill panel damage. Depending on the nature of the damage, either the entire section has to be replaced or parts of it by way of three separating sleeves.SSP282_0308 Rear end The rear end has been completely redeveloped. The two large central castings are the one connecting the sill panel/ longitudinal member and the C/D-pillar connecting element. The sill panel/longitudinal member connecting element is the largest casting. It supports the entire rear sub-frame and links the rear longitudinal member to the sill panel. Its great rigidity is designed to protect the tank in between in the event of a rear-end collision.SSP282_032Large upper castings Extruded sectionsThe C/D-pillar connecting element (large upper casting) accommodates the suspension strut at the top and the seat belt at the front, in addition to forming the terminating side section of the roof frame. The large upper and lower castings are interlinked by way of two straight extruded sections and form the framework for the air suspension strut holder.Large lower castingsSSP282_0339 BodyBoot lidFoam encasing Electronic boot lid lock with microswitchSSP282_035 Motor for automatic closing aid Bowden cable CatchA standard feature is an automatic closing aid, which is actuated by a Bowden cable separately from the catch. After the latch has closed, a mechanism pulls the catch downwards, overcoming the build-up of pressure occurring. On locking, a microswitch in the boot lid lock transmits a signal to the control unit to activate the automatic closing aid.The drive unit is only encased in foam and inserted between side panel and battery.10 Automatic boot lidHinge mechanism (open)Boot lid control unit J605Button in driver's doorButton on boot lidVehicle key SSP282_036Pressing the button in the driver's door or on the boot lid, or remote control actuation, effects release and motor-driven opening of the boot lid. Automatic boot lid closing can only be implemented by way of the boot lid button. An electric motor flanged directly to the swivel joint of the right boot lid hinge opens or closes the boot lid.In the event of manual boot lid actuation, the electric motor is disconnected by way of a magnetic coupling, thus permitting the boot lid to be moved by hand. On closing the boot lid, the drive is deactivated via a microswitch at the latch and the automatic closing aid activated.As a general rule, interruption of automatic actuation always causes the boot lid to be disconnected from the drive unit and thus set to manual mode.11 BodyFront doors The doors are made up of a combination of aluminium panels, aluminium sections and aluminium castings. Optimised rib geometry and wall thickness in the hinge and lock mounting castings formed the basis for ideal implementation of the lightweight construction concept. Door shell and door frame are connected at the door pre-assembly stage by means of fitted bolts to ensure the accurate assignment of both components. Window lifter frame, window lifter motor/gear mechanism, door control unit and speaker are pre-assembled on a base plate and bolted to the door subframe.SSP282_039Rear doors Large, high-strength side impact members are integrated into the door to provide even load distribution in the event of side impact.12 SeatsBackrest adjustment – The angle of the top 1/3 of the backrest can be adjusted by 15° for enhanced shoulder comfort.Crash-active, electronic head restraint with 70 mm height adjustmentLumbar support with massage function over a length of 60 mmThorax/pelvis side airbag Backrest fanSSP282_116 Electric seat depth adjustment – As the structure moves forwards it pulls the padding with it and so extends the seat area by 50 mm.Seat cushion fanA new seat concept was developed for the Audi A8 ´03. The basic seat features the following standard functions: – Electric seat length, height and angle adjustment – Electric backrest angle adjustment – Front crash-active head restraints (refer to Page 21) The basic seat can additionally be fitted with – Four-way lumbar support – Seat memory for driver and front passenger – Electrically adjustable head restraints – Electric belt height adjustersExtra features of sports and comfort seats: – Electric top 1/3 backrest adjustment – Electric seat depth adjustment Optional extras for comfort seat: – Climate function (refer to Page 85) – and/or massage function The massage function is implemented by way of rhythmic action of the electromechanical lumbar support, thus massaging and relaxing the back muscles. The fixed rear seat bench versions correspond to those of the front seats, with the third head restraint being fully retractable. Electric individual seats are however only available as "Basic" and "Comfort" versions.13 Passenger ProtectionSystem layoutG 283G 284K145 J623 J285/K75AIRBAGAIRBAGOFFE224AUS EINT16 J533N95/G85 N131J234E24 J526 N199E25 N200G179N153N154G180N201N202N251 G 256N196N198N197N252 G 257J393J65514SSP282_068 Use is made in the Audi A8 ´03 of the 8.4E+ The wide range of sensors permits detection airbag system with the aim of attaining greater not only of head-on collision and side impact, occupant safety whilst reducing the impact. but also of rear-end collisions. This was achieved, for example, by way of twostage front airbag triggering, active front head restraints and a battery cut-off element.Key E24 Driver side belt switch E25 Front passenger side belt switch E224 Airbag disabling key switch, front passenger side G85 Steering angle sender G179 Side airbag crash sensor, driver side (B-pillar) G180 Side airbag crash sensor, front passenger side (B-pillar) G256 Rear side airbag crash sensor, driver side G257 Rear side airbag crash sensor, front passenger side G283 Front airbag crash sensor, driver side G284 Front airbag crash sensor, front passenger side J234 Airbag control unit J285 Control unit with display in dash panel insert J393 Convenience system central control unit J526 Telephone/telematics control unit J533 Data bus diagnostic interface (gateway) J623 Engine control unit J655 Battery cut-off relay K75 Airbag warning lamp K145 Airbag disabled warning lamp, front passenger side N95 N131 N153 N154 N196 N197 N198 N199 N200 N201 N202 N251 N252 Driver side airbag igniter Airbag igniter 1, front passenger side Belt tensioner igniter 1, driver side Belt tensioner igniter 2, front passenger side Rear belt tensioner igniter, driver side Rear belt tensioner igniter, front passenger side Rear belt tensioner igniter, centre Side airbag igniter, driver side Side airbag igniter, front passenger side Rear side airbag igniter, driver side Rear side airbag igniter, front passenger side Curtain airbag igniter, driver side Curtain airbag igniter, front passenger side 16-pin connector (diagnostic connection)T1615 Passenger ProtectionBlock diagram1513G283 J655G284G179E224 2J234F138N95N131N199N200N201N202Key E24 Driver side belt switch E25 Front passenger side belt switch E224 Airbag disabling key switch, front passenger side F138 Airbag coil connector/return spring with slip ring G179 Side airbag crash sensor, driver side G180 Side airbag crash sensor, front passenger side G256 Rear side airbag crash sensor, driver side G257 Rear side airbag crash sensor, front passenger side G283 Front airbag crash sensor, driver side G284 Front airbag crash sensor, front passenger side J234 Airbag control unit J655 Battery cut-off relay N95 N131 N153 N154 N196 N197 N198 N199 N200 N201 N202 Driver side airbag igniter Airbag igniter 1, front passenger side Belt tensioner igniter 1, driver side Belt tensioner igniter 2, front passenger side Rear belt tensioner igniter, driver side Rear belt tensioner igniter, front passenger side Rear belt tensioner igniter, centre Side airbag igniter, driver side Side airbag igniter, front passenger side Rear side airbag igniter, driver side Rear side airbag igniter, front passenger side16 G180G256G257E24E254567N251N252N153N154N196N198N197SSP282_069Additional signals N251 Curtain airbag igniter, driver side N252 Curtain airbag igniter, front passenger side 1 2 Battery A (positive) Positive connection to starter B and alternator C Terminal 58s Drive system CAN (High) Drive system CAN (Low) Crash signal Airbag disabled warning lamp, front passenger side K1453 4 5 Colour code 6 = Input signal = Output signal = Positive supply = Earth 717 Passenger ProtectionSafety systems2-stage front airbags The 2-stage triggering of the front airbags provides optimum restraint in crash situations at around 30 km/h. There is a separate firing pellet for each stage in the driver's and front passenger's airbag. These ignite successively at specified time intervals.Ring airbagSSP282_070A so-called "ring airbag", which inflates like a life belt, is used on the driver's side. This radial inflation method affords particular protection to drivers sitting very close to the steering wheel. The centre of the steering wheel does not move as the airbag unfolds and is inflated in the form of a ring. A rectangular fabric layer is additionally sewn to three sides of the ring. One side is left free to allow the airbag to slide over the nonmoving centre section of the steering wheel.This airbag design satisfies the requirements of the latest American legislation and involves compliance with biomechanical values for so-called "Out Of Position" (OOP) driver posture. If the driver's head or upper part of the body is very close to the steering wheel at the time of airbag unfolding (OOP), this airbag concept can prevent serious injury.18 Front passenger's airbag deactivation An optional feature of the Audi A8 ´03 is a new airbag disabling key switch for the front passenger's side E224. Two resistance paths are integrated into this switch to permit detection of individual faults. A fault in the key switch is indicated by flashing of the front passenger's side airbag disabled warning lamp K145 located in the centre console next to the hazard warning switch.SSP282_081Front knee airbags (USA)SSP282_114The USA version of the Audi A8 ´03 is fitted with driver's and front passenger's knee airbags as standard, thus optimising driver and front passenger movement in a crash situation.In this way, severe impact in the knee zone is avoided. Knee airbags are required by legislation in the USA.19 Passenger ProtectionDetection of rear-end collision Rear-end collisions are detected by way of a sensor in the airbag control unit J234 and a plausibility function involving the driver's and front passenger's front airbag crash sensors G283 and G284.Up-front sensors For the first time, use is made in the Audi A8 ´03 of so-called up-front sensors. These take the form of two additional frontend acceleration sensors on the right and left beneath the corresponding headlight.SSP282_072Lateral acceleration sensors Further acceleration sensors are located at the B and C-pillars.C-pillar sensorB-pillar sensorSSP282_073 20 Active head restraints The front seats of the Audi A8 ´03 are provided with active head restraints. With this system, the head restraints move forwards in the event of a rear-end collision to shorten the distance between head and restraint. The danger of cervical vertebrae injury is greatly diminished by reducing the relative acceleration between shoulder and head. In head-on collision situations, the mechanics of centrifugal weight are neutralised.SSP282_082Belt tensioners Five belt tensioners are fitted as standard. There is no centre belt tensioner if the rear seats are electrically adjustable.21 Passenger ProtectionBattery cut-off relay J655 The battery cut-off relay is a battery isolating element designed to disconnect starter and alternator power from the electrical system in the event of a crash.Terminal 30, battery 87 Terminal 15 Vehicle earth Crash signal DiagnosisPin A B 1 2 3 4Input/output Input (screw connection) Output (screw connection) Input (plug connection) Input (plug connection) Input (plug connection) Input (plug connection)Description Ubat. term. 30/battery Output Positive power supply, interruptible Earth from airbag control unit J234 Crash signal from airbag control unit J234 Diagnostic wire from airbag control unit J234Block diagram J644 Energy management control unit J655 Battery cut-off relay30 154 A +31J655B J644 31 2SSP282_076 22 Fitting location The battery cut-off relay is located in front of the battery.Triggering The airbag control unit J234 provides the battery cut-off element with the triggering command via a discrete wire. Triggering of this element by the airbag control unit causes a white panel to appear in the element window instead of a copper coil. Following isolation, the battery cut-off element can be manually reset by way of the yellow knob.SSP282_083Control element test The control element test in the airbag control unit also triggers the battery cut-off relay. It should be ensured that the relay is manually reset, as otherwise the battery cannot be charged.SSP282_079WindowReset knobSSP282_077 23 Engine, MechanicsTechnical dataV8 4.2 l 5V engine Engine code letters: Capacity: Bore: Stroke: Compression ratio: Power:BFM460 240 220 200 1804,1723 cm440 420 40084.5 mmTorque [Nm]93.0 mm360 340 320 300 280140 120 100 80 60 4011 : 1 246 kW (335 hp) at 6,500 rpm 430 Nm at 3,500 rpmTorque: Camshaft adjustment range: Valves: Engine management: Emission standard: Firing order: Capacities: Consumption:26020004000600022° CS advance 5 per cylinderEngine speed [rpm] SSP282_002ME7.1.1EU 41-5-4-8-6-3-7-2 7.5 l engine oil (incl. filter) Urban: 17.5 - 17.6 l/100 km Non-urban: 8.7 - 8.8 l/100 km Average: 11.9 - 12.0 l/100 kmAcceleration 0 - 100 km/h:0 - 80 km/h – 4.8 s 0 - 100 km/h – 6.3 s Premium Plus Unleaded 98/95 RONFuel:SSP282_012CS = Crankshaft24Power [kW]380160 V8 3.7 l 5V engine Engine code letters: Capacity: Bore: Stroke: Compression ratio: Power:BFL3 3,697 cm460 440 420 400240 220 200 18084.5 mmTorque [Nm]82.4 mm360 340 320 300 280140 120 100 80 60 4011 : 1 206 kW (280 hp) at 6,000 rpm 360 Nm at 3,750 rpmTorque: Camshaft adjustment range: Valves: Engine management: Emission standard: Firing order: Capacities: Consumption:26020004000600013° CS advance 5 per cylinderEngine speed [rpm] SSP282_001ME7.1.1EU 41-5-4-8-6-3-7-2 7.5 l engine oil (incl. filter) Urban: 17.1 - 17.3 l/100 km Non-urban: 8.6 - 8.8 l/100 km Average: 11.7 - 11.9 l/100 kmAcceleration 0 - 100 km/h:0 - 80 km/h – 5.6 s 0 - 100 km/h – 7.3 s Premium Plus Unleaded 98/95 RONSSP282_011Fuel:Power [kW]38016025 Engine, MechanicsV8 5V 3.7 l/4.2 l engine The 3.7 l and 4.2 l V8 engines were adopted from the predecessor model with certain modifications. These modifications relate to the intake and exhaust systems and are described in the following. Design and operation are described in SSP 217.Variable-intake manifold in 4.2 l engine This takes the form of a 2-stage variable-intake manifold made of a die-cast magnesium alloy, bonded and bolted together in four sections. The two-stage design permits the use of two intake paths with large cross section. The intake manifold must be replaced as a complete unit when performing repairs.SSP282_013 26 – Long intake path, 705 mm – Changeover flap closed for high torqueSSP282_014Each of the two splined shafts is fitted with four flaps per cylinder bank. The shape of the rubber-encased flaps ensures unimpeded air flow in the torque position and reliable power position sealing of the duct. This is a prerequisite for utilisation of the gas-dynamic resonance effects. In the power position, the backs of the flaps take on the shape of the duct wall, thus allowing low-resistance intake air flow into the cylinders. Mechanical couplings provide a link with the vacuum units for adjustment of the two shafts and thus the intake manifold flaps.SSP282_016– Short intake path, 322 mm – Changeover flap open for high power with high air throughput Changeover from long to short at 4,480 rpm Changeover from short to long at 4,320 rpmSSP282_01527 Engine, MechanicsVariable-intake manifold in 3.7 l engineChangeover flap, stage 3Intake air (inlet)Vacuum unit Changeover flap, stage 3t nic o ctr e ele valv m e Fro rottl Tho hrttleInjector mountsChangeover flap, stage 2 (open) Vacuum unit Changeover flap, stage 2Resonance tube, cyl. 5 (inlet end)SSP282_017This is the same 3-stage variable-intake manifold as previously fitted in the V8 engine.Due to the piston stroke of only 82.4 mm, three resonance tube lengths are required to achieve resonance effects in the lower engine speed range. Changeover points: – Long to short at 3,280 rpm – Short to long at 3,120 rpm – Short to shorter at 5,120 rpm – Shorter to short at 4,920 rpmOperation of the 3-stage variable-intake manifold is described in SSP 217.28 Air cleaner A round filter is employed instead of a flat filter to achieve a larger filter surface area for more air throughput in view of the different amount of space available.SSP282_018Furthermore, an additional intake air flap in the air cleaner is opened as a function of load at engine speeds as of 3,000 rpm to attain the large volume of air required at full throttle. This flap enables additional air to be drawn in from the engine compartment and reduces the air velocity in the air cleaner.SSP282_01929 Engine, MechanicsSystem layoutActuators/sensorsHot-film air-mass meter G70Engine speed sender G28Hall sender G40 (bank 2) and Hall sender 2 G163 (bank 1) Pedal position sender/accelerator pedal module with accelerator pedal position sender G79 and accelerator pedal position sender 2 G185Lambda probe G39 (bank 1) Lambda probe II G108 (bank 2) Lambda probe after catalyst G130 (bank 1) Lambda probe II after catalyst G131 (bank 2)Brake light switch F and Brake pedal switch F47Throttle valve control part J338 with Throttle valve drive G186 (electric power control) Throttle valve drive angle sender 1 G187 Throttle valve drive angle sender 2 G188Clutch pedal switch F36 (manual gearbox only)Coolant temperature sender G62Dash panel insert CANKnock sensor I G61 (bank 1) and Knock sensor II G66 (bank 2)Control unit with display in dash panel insert J285Additional signals: – Air conditioner requirement – Cruise control switch – Term. 50, stage 1 – Automatic gearbox selector lever position 30 Fuel pump relay J17 Fuel pump G6Engine control unit J623Fuel pump II relay J49 Fuel pump G23Injectors N30, N31, N32, N33 (bank 1)Steering angle sender G85Intake manifold changeover valve N156 and Intake manifold changeover valve 2 N261Injectors N83, N84, N85, N86 (bank 2)Ignition coils N (no. 1 cyl.), N128 (no. 2 cyl.), N158 (no. 3 cyl.), N163 (no. 4 cyl.)Automatic gearbox control unit J217Left electrohydraulic engine mounting solenoid valve N144 and Right electrohydraulic engine mounting solenoid valve N145Ignition coils N164 (no. 5 cyl.), N189 (no. 6 cyl.), N190 (no. 7 cyl.), N191 (no. 8 cyl.)Activated charcoal filter system solenoid valve 1 N80 ESP control unit J104 Torque rod valve N382 Secondary-air pump relay J299 and Secondary-air pump motor V101Secondary air inlet valve N112 Data bus diagnostic interface J533 Airbag control unit J234 Lambda probe heater Z19 (bank 1) and Lambda probe 2 heater Z28 (bank 2)Throttle valve control part J338 With throttle valve drive G186Drive system CANLambda probe 1 heater after catalyst Z29 Lambda probe 2 heater after catalyst Z30 Additional signals: – Starter relay term. 50, stage 2 – Tank leakage pump (USA only) – Air conditioner compressor (out)Inlet camshaft timing adjustment valve 1 N205 (bank 1) and N208 (bank 2) SSP282_091Diagnosis CAN Engine, MechanicsElectrohydraulic torque reaction supportStress-free alignment of the torque reaction support is implemented by way of the lock nut.Lock nut Isolation diaphragm Shell Top section Plastic ring with sheet metal ring Connecting pipe Bellows cap Solenoid Upper section of nozzle plateSSP282_020 Bottom sectionThe purpose of torque reaction support is to cushion the drive shaft and propshaft torque. The position of the support bearing at the front right of the engine is ideal, as this is where the engine motion resulting from drive shaft and propshaft torque accumulates. The torque reaction support is divided into two halves by the plastic ring, the sheet metal ring and the isolation diaphragm. Both halves are filled with fluid (glycol). The isolation diaphragm is flexibly linked to the plastic and sheet metal rings. If the torque reaction support is subjected to load, the fluid can be displaced between the top and bottom section by way of a connecting pipe, the dimensions of which are such that it acts as a restrictor as of a defined frequency.When the solenoid is deenergised, vibration causes the plastic ring with sheet metal ring and isolation diaphragm to oscillate as well. The moments are damped slightly and thus transmitted to a lesser extent to the body. As of an engine speed of approx. 1,100 rpm and a vehicle speed of 5 km/h, the solenoid is energised and attracts the sheet metal ring together with the plastic ring. This restricts the movement of the isolation diaphragm, which can then only vibrate slightly. In this case there is a high level of vibration damping and the torque reaction support is "hard".32 Exhaust systemExhaust manifold Lambda probe G39, cylinder bank 1 Two-stage catalytic converterLambda probe after catalyst G130Connecting pipe Lambda probe II G108, cylinder bank 2 Lambda probe II after catalyst G131SSP282_028With the 4.2 l and 3.7 l engines, the exhaust system is of the dual-flow type. It consists of two underbonnet catalytic converters, two flexible decoupling elements, two reflection-type front silencers, an absorption-type centre silencer and two reflection-type rear silencers with visible tail pipes. The catalytic converters are of the twostage type and fitted with a ceramic monolith.Thin-walled ceramic monoliths are used to improve cold starting behaviour. On environmental grounds, the centre silencer is fitted with long-fibre glass wool instead of basalt wool. A connecting pipe is located directly upstream of the centre silencer. This forms the joint between the two exhaust pipes required for acoustic reasons.33 Engine, MechanicsFuel tankThe fuel tank capacity is approximately 90 litres. The basic unit consists of two plasma-welded stainless steel shells. There are no differences between petrol and diesel engine versions. The filler neck is a single piece and welded to the basic unit. For reasons of crash safety, the centre section of the filler neck takes the form of a corrugated tube. In crash situations, this section is subject to defined deformation to prevent cracks and fuel spillage. To create the best possible ergonomic conditions for the rear passengers in combination with maximum luggage compartment volume, the two tank compartments are shallower than in the predecessor model. The additional expansion tank has been taken out of the filler pipe and moved to the fuel tank.Activated charcoal filterThe tubing system for the tank breather at the filler pipe has been considerably simplified as compared to the predecessor model. With the exception of diesel vehicles, the pipe connections have been converted to quickrelease couplings. A new feature is the use of a 2-stage delivery pump for each tank chamber in separate reservoirs. The fuel level is measured by two immersion tube senders combined with two angle senders.Fuel filler neckThe switch from plastic to stainless steel was necessary for compliance with American LEV II legislation, which demands a further significant reduction in permissible emission levels.Tank compartment breatherDiagnostic connection SSP282_007 34 Interior of fuel tank (filling)Float-type shutoff valve Filler pipeBreather pipe to filler pipeReservoir with pump unit, rightReservoir with pump unit, leftBaffle housing of expansion tankSSP282_006 Overflow channelThe fuel is conveyed via the filler pipe into the right tank chamber (as viewed in direction of travel). The fuel passes via an additional overflow channel at the end of the filler pipe predominantly into the right pump reservoir. Use of the small overflow channel ensures that even small quantities of fuel (e.g. filling from canister) pass directly into the pump reservoir. The breather function for the side compartments is provided by two breather pipes to the main chamber.Routing the filler pipe beneath the longitudinal member means that the lowest point of the pipe is not at the connection to the fuel tank, thus producing a siphon effect. A residual quantity of fuel remains in the filler pipe. This necessitates a separate pipe to the filler neck for the main chamber breather function and for OBD II leakage diagnosis. When the tank is full, the filler hose is closed by a float-type shutoff valve at the end of the filler pipe.35 Engine, MechanicsExpansion tankInlet pipe from tank filler neckFloat-type rollover valve Breather pipeSuction jet pump intake connectionFloat-type shutoff valveSSP282_009The expansion tank (capacity approx. 2 litres) consists of a plastic housing clipped to the upper shell of the tank. The internal expansion tank houses a floattype rollover valve and a small suction jet pump which constantly pumps the tank empty whilst driving.Function The main functions of the float-type rollover valve are as follows: – Closing-off of pipe to filler neck in the event of rollover – Closing in dynamic driving mode – Closing by rising of float in valve in the event of a brief excess of fuel in the tank due to sloshing Closing-off of the pipe to the activated charcoal filter stops fuel overflowing into it.36 Two-stage fuel pumpsMain stage delivery endMain stage suction end ReturnOverflowMain stage pump unit Pre-stage pump unit Pre-stage suction endReservoirPre-stage delivery end Fuel tank Main stage suction endSSP282_003The two fuel pumps (petrol engine) are of the two-stage flow type. The first stage (pre-stage) pump unit draws in fuel from the bottom of the tank and conveys it into the reservoir. This ensures that even small residual quantities can be transported. The second stage (main stage) pump unit draws in fuel directly from the reservoir.The reservoirs with pumps and immersion tube senders rest on and are clipped to the bottom of the tank. Flanged covers provide access to the components. Single-stage pumps are used for diesel engines (Common Rail). On account of the higher viscosity of diesel fuel, pre-delivery (extraction from bottom of tank) is not implemented by way of separate pump units, but rather by suction jet pumps.37 Engine, MechanicsFuel system (hydraulics)Pressure regulator (4 bar)Fuel pump G23Fuel pump G6Suction jet pumpSSP282_005When the ignition is switched on (terminal 15), the fuel pump G23 conveys a maximum volume to the pressure regulator at the fuel rail to achieve short starting times. The pump G6 also conveys fuel to the pressure regulator and additionally into the pipes for the two suction jet pumps in the side tank compartments. The suction jet pumps convey the fuel from the side compartments "diagonally" into the pump reservoirs.Such pipe routing prevents dry running of a pump in critical driving situations such as cornering or if the vehicle is at an extreme angle. The return pipe is shared by both reservoirs. If one reservoir is full, the pipe is closed by a non-return valve and the entire return volume runs into the second reservoir. If both reservoirs are full, the non-return valves are overridden and the fuel runs into the tank.38 Tank senders The fuel level is sensed by two immersion tube senders and two angle senders. A new feature is the design of the angle sender, which is equipped with a magnetically passive position sensor. The ceramic substrate is provided with 51 series-connected film resistors with individual pick-off. Fitted with a small clearance on top of this is a magnetically soft foil with the same number of spring contacts. The magnetic position sensor beneath the ceramic substrate pulls the spring contacts onto the pick-offs. The electrical output signal varies proportionally as a function of the position of the magnet. Thanks to the magnetic coupling it was possible to provide a hermetic seal for the measurement system.Magnetically soft foilCeramic substrate with film resistorsSSP282_010 Magnetic position sensorAdvantages: – Longer service life thanks to noncontacting measurement system – Protection against dirt and deposits – Low contact currentsFuel gauge sender 3 G237 (immersion tube sender, 70 - 158 W)Fuel gauge sender G (immersion tube sender, 70 - 158 W)Fuel gauge sender 2 G169 (angle sender, 50 - 300 W)Fuel gauge sender 4 G393 (angle sender, 50 - 300 W) Fuel pump G23 Fuel pump G6Direction of travelSSP282_008 Control unit with display in dash panel insert J285 Fuel gauge G1Characteristic curve adaption39 Engine, MechanicsDetermining fuel levelbc aSSP282_004The fuel level is determined by way of a logical system of immersion tube and angle sender signals.The sender signals are evaluated by the dash panel insert. All senders are connected in parallel. The wires are bunched beneath the fuel tank, thus enabling resistance measurements to be taken without the need for further dismantling.a - Low levels are determined exclusively by way of the angle sender measured values b - High levels are determined exclusively by way of the immersion tube sender measured values. c - Medium levels are determined by a combination of all sender signals40 Automatically controlled startingThe automatic start control is integrated into the engine control unit. A new feature is that starter control is no longer implemented by way of the ignition/ starter switch D (switching of terminal 50), but rather it is performed automatically by the engine control unit. Release for starter actuation is always transmitted by the entry and start authorisation control unit J518 to the engine control unit J623. In addition to general release by the immobilizer, the following start release conditions also have to be satisfied: – Start signal from entry and start authorisation switch E415 or entry and start authorisation button E408 – 1 Clutch pedal pressed, signal from clutch pedal switch F194 (manual gearbox only) – 1 Selector lever position P or N (automatic gearbox control unit J217) – 2 In the event of start signal via entry and start authorisation button E408, brake must be pressed (signal from brake light switch F via separate interface)1As a safeguard, P/N signal or signal from clutch pedal switch F194 must be applied to the separate interfaces of the two control units (J623 and J518).2Additional safeguard, as entry and start authorisation button E408 can be actuated by front passenger.41 Engine, MechanicsSequence of operations 1 Entry and start authorisation switch E415/ entry and start authorisation button E408 The driver triggers a brief start signal (min. 20 ms) by turning the ignition key to start position or by pressing the entry and start authorisation button E408.2 Entry and start authorisation control unit J518 The entry and start authorisation control unit checks for authorisation – in the form of information on selector slide position N or P – from the automatic gearbox control unit J217 and for brake application in the case of a start signal from the entry and start authorisation button E408. If the start prerequisites have been satisfied, the entry and start authorisation control unit J518 transmits a start request – terminal 50 ON – to the engine control unit J623. The entry and start authorisation control unit J518 also controls the terminal 15 and terminal 75x circuits.3 Engine control unit J623 Application of selector slide position P/N or "clutch pressed" information to the engine control unit (separate interface) causes the two starter relays J53 and J695 to be actuated simultaneously. The relays then switch terminal 50 for starter actuation. The starter operates and cranks the engine. On exceeding a defined engine speed, the engine control unit J623 recognises that the engine has started and the relays are deenergised (thus terminating starting process). As a safeguard, two relays are connected in series. In the event of fusion welding of the make contacts (relay remains closed following deenergisation), the engine control unit J623 can thus interrupt the circuit (terminal 50) by way of the other relay in each case. The two relays are deenergised alternately in order to ensure even make contact wear (break spark) in both relays. The deenergisation sequence alternates. Relay operation is monitored and faults diagnosed by evaluating the alternating deenergisation with the aid of the terminal 50R interface. The terminal 50R interface represents a link with terminal 50 and provides the engine control unit J623 with feedback for start control/diagnosis. Automatically controlled starting is not permitted in the event of undervoltage or a system fault. The engine can however be started manually by way of corresponding start signal actuation. To relieve the load on the starter and battery, the relay actuation time is limited to approx. 10 seconds per starting operation (automatic or manual starting).42 Block diagramD1 E4082 1 0 2 1 0E415 N3766xSTOPSTART12 58sJ51850R 15 75x 30 50R 3 J623 1 2J329J694J53J695SSP282_024D1 E408 E415 J53 J329 J518Inhibitor reading unit Entry and start authorisation button Entry and start authorisation switch Starter motor relay Terminal 15 voltage supply relay Entry and start authorisation control unitJ623 J694 J695 N376Engine control unit Terminal 75x voltage supply relay Starter relay 2 Ignition key withdrawal lock magnetAdditional signals Colour code = Input signal = Output signal = Positive supply = Earth 3 1 2 F - Brake light switch Manual gearbox - F194 Clutch pedal switch Automatic gearbox - Selector lever position from automatic gearbox control unit J217 Terminal 50/starter43 Engine, MechanicsExplanatory notes on internal control unit sequence chart Request for starting (terminal 50 ON from entry and start authorisation control unit J518) energises the two relays. Locking-in takes place during the initialisation phase of engine control unit J623. After initialisation, the engine control unit assumes further starter control tasks as described under item 3.Term. 15 Start request from driver authorisation system Engine start recognition (engine speed) Relay deenergisation by engine control unit Term. 50R/diagnosis Engine control unit initialisation Engine control unit active Starting Ignition onStart request retained manuallyStart request briefly activated Engine speed increases Starter speed Relay deenergisationStarter operation feedback signalLocking-inEngine control unit active Engine runningSSP282_06444 GearboxTo satisfy high comfort requirements, the Audi A8 ´03 features a new 6-speed automatic gearbox capable of handling a high engine torque of max. 600 Nm. Two different versions are available: – 420 Nm for the V8 5V 4.2 l or 3.7 l engine and – 600 Nm for the V8 TDI 4.0 l or 6.0 l W12 engine Design and operation of the 09E gearbox are described in SSP 283 (Part 1) and SSP 284 (Part 2).SSP282_043Technical data Designation: Factory designation: ZF designation: Type: 09E AL 600-6Q 6HP-26 A61 6-speed planetary gearbox, featuring electrohydraulic control with hydrodynamic torque converter and slip-controlled lockup clutch Via mechatronic system (integration of hydraulic control unit and electronic control to form one unit) Front/rear axle torque distribution: Gear oil capacity (total): Gear oil capacity (replacement): Total weight: Max. torque transmission:420 Nm for V8 5V 4.2 l /3.7 l engine 600 Nm for V8 TDI 4.0 l /W12 6.0 l engine 50/50 10.4 litres ATF 10 litres ATF approx. 138 kg (420 Nm version) approx. 142 kg (600 Nm version)45Control: GearboxHighlights of automatic gearbox 09E (AL 600-6Q) The 6-speed planetary gearbox is based on the Lepelletier principle. This concept is characterised by harmonic gear ratio steps and the implementation of six forward gears and one reverse gear with only five selector elements.SSP282_044Use is made in this gearbox of a new internal gear oil pump featuring a lower delivery volume and reduced leakage. In addition, it was possible to achieve optimisation of the oil supply with lower leakage rates in the hydraulic control system. The "stationary disconnection" function reduces engine output when the vehicle is stopped with a gear engaged by interrupting power transmission.A particularly noteworthy feature of the 09E automatic gearbox is the relocation of the front-axle differential (flange shaft) to in front of the torque converter. The distance between flange shaft and engine flange is now only 61 mm (01L = 164 mm).SSP282_04546 The mechatronic system integrated into the gearbox housing is a new development, combining the hydraulic control unit, sensors, actuators and electronic gearbox control unit in a coordinated assembly.All data exchange with the vehicle periphery takes place via the drive system CAN, thus reducing the number of vehicle periphery interfaces to a minimum (11 pins) and at the same time enhancing operational reliability.SSP282_04647 GearboxIn terms of the following functions, there are interesting new aspects to the shift mechanism in the new Audi A8 '03: – – – – – Shift mechanism kinematics Ignition key removal lock Selector lever lock Selector lever lock emergency release Selector lever/lock button kinematicsIgnition key removal lock Major modifications have been made to operation of the ignition key removal lock and selector lever lock (shiftlock). On account of the new entry and start authorisation switch E415, there is no mechanical link between the shift mechanism and ignition lock (locking cable).Selector lever/button kinematics To prevent inadvertent shifting into selector lever position "S", a change has been made to the selector lever kinematics such that switching to "S" involves pressing the button in the gearstick knob. A small gear mechanism is provided in the gearstick knob to reduce the required button operating force.Selector lever lock emergency release The locking rod is actuated by the application This modification means that the selector lever of pressure, which means changes have also remains locked in position "P" in the event of been made to kinematics and gearstick knob malfunctions or power supply failure assembly (refer to Workshop Manual). (e.g. battery flat). Selector lever lock emergency release is provided to enable the vehicle to be moved (e.g. towed) in such situations.SSP282_048 48SSP282_049 Running GearFront axleThe familiar four-link front axle was retained for the Audi A8 '03. A significant new feature is the air suspension in combination with electronically controlled dampers (refer to Section on air suspension). All axle components are new on account of the geometric and kinematic modifications as compared to the predecessor model, the air suspension and the weight reductions achieved.Front axle highlights – – – – – – Subframe Auxiliary frame Anti-roll bar Wheel bearing housing Wheel bearing with wheel speed sensing Mounting bracket for damper unitFront axle design and operation are described in SSP 285.SSP282_050 49 Running GearRear axleThe rear axle is a more advanced version of the familiar Audi A8 trapezium-link axle. All axle components are new on account of the geometric and kinematic modifications as compared to the predecessor model, the air suspension and the weight reductions achieved.Rear axle highlights – Use of air suspension in conjunction with electronically controlled damping – Aluminium subframe to help reduce weight – Connection of anti-roll bar to trapezium link – Use of shorter track rod to reduce change in toe on compression and extension of suspension – Use of ball studs to connect wheel bearing housing and track rod, thus reducing secondary spring rate – Use of slotted bonded rubber bushes in upper transverse link and connection between trapezium link and subframeRear axle design and operation are described in SSP 285.50SSP282_051 4-level air suspensionThe introduction of the Audi A8 ´03 is accompanied by a system featuring new technical details and functions. The major differences with respect to the familiar Audi allroad quattro® system are as follows: EDC instead of PDC damping The control system makes allowance for the currently applicable driving status. Wheel movement (unsprung masses) and body movement (sprung masses) are detected. Various damping characteristic curves are implemented within the scope of three selectable programs (modes) and each damper can be controlled individually. Optimal comfort and road safety are thus always guaranteed whichever mode is set (comfort or sports). The term "mode" thus describes a coordinated combination of adaptive suspension program and damping map.Control concept Integration into the MMI makes for convenient, logical and easy to remember control action.Extended range of sensors Use is made of three acceleration sensors to detect body movement.SSP282_052External air springs The air spring not only replaces the steel spring, it also offers major advantages (refer to SSP 242). The new external routing of the air spring through an aluminium cylinder permits the use of thinner-walled bellows. This results in an even more sensitive response to road surface irregularities.SSP282_053 51 Running GearSystem layoutRear axle acceleration sensors Control unit with display in dash panel insert J285 Front information and display and operating unit control unit J685 Rear axle air suspension strutsPressure accumulator Adaptive suspension control unitFront axle air suspension strutsSSP282_054Rear axle level sensorsFront axle level sensors CompressorSolenoid valve blockFront axle acceleration sensorsDesign and operation of 4-level air suspension are described in SSP 292.52 Electric parking brakeThe brake pads are applied by way of a spindle mechanism. Gear unit and motor are flanged to the brake caliper. Implementation of the parking brake function involves translating the rotation of the drive motor into a very short brake piston stroke. This is achieved through the use of a swash plate mechanism in combination with the spindle mechanism. The emergency braking function is initiated via the parking brake button and transmitted to all four wheels by the brake hydraulics. The following functions are provided by the electric parking brake: – – – – Parking brake function Emergency braking function Holding function when driving off on a hill Brake pad wear indicatorDesign and operation of the electric parking brake are described in SSP 285.Brake caliperBrake pistonElectric motorElectrical connectionToothed beltSwash plate mechanismSpindleSSP282_055Brake disc53 Running GearACC (Adaptive Cruise Control)Adaptive Cruise Control is a new system designed to assist drivers and offers a much wider range of functions than the conventional Tempomat. Driver convenience is further enhanced, as fewer accelerator and brake pedal operations are required. Speed restrictions and safety factors are reliably observed and the flow of traffic thus better regulated.SSP282_057Summary of Adaptive Cruise Control (ACC) The basic Adaptive Cruise Control function is to maintain a driver-selectable distance from the vehicle in front. ACC thus represents the logical next step on from the original cruise control system. The distance from and speed of the vehicle in front are determined by a radar sensor. If the distance is greater than desired, the vehicle is accelerated until the required speed input by the driver is achieved. If the distance is less than desired, the vehicle is decelerated by reducing power, changing gear and if necessary applying the brakes. In the interests of comfort, maximum possible braking is restricted to approx. 25 % of the maximum deceleration potential of the brake system (full braking). The control action is designed to assist the driver and thus contributes to greater road safety. In certain traffic situations, active braking by the driver may still be necessary.54 ACC system limits – ACC is designed to assist the driver and is not a safety system. – ACC is not a fully autonomous driving system. – ACC provides control in a speed range of 30 - 200 km/h. – ACC does not react to stationary objects. – Radar operation is impaired by rain, spray and slush. – Tight bends may restrict operation on account of the limited radar detection range.Radar sensor An adapter plate permits fitting and adjustment at a holder bolted to the centre of the bumper bracket. For details, refer to current Workshop Manual. Design Sender and control unit are integrated into one housing - the distance regulation control unit J428. The entire assembly has to be replaced if the control unit is defective.HolderVertical adjusting screwDistance regulation control unit J428 with radar sensorMounting holeSSP282_058 Horizontal adjusting screw 55 Running GearSetting desired speed The desired speed is the maximum speed to be controlled by the ACC on an open road (corresponds to cruise control system function). Pressing the SET button stores the current speed as desired speed.SSP282_061The set speed is displayed by a bright red LED in the speedometer rim and the "ACC active" symbol appears in the speedometer. The "ACC active" status is indicated by faint red illumination of all LEDs in the range between 30 and 200 km/h.SSP282_06056 Setting desired distance The desired distance from the vehicle in front can be set by the driver in four stages. The distance set by the ACC is governed by the respective vehicle speed. The distance increases with increasing vehicle speed. The minimum setting ensures compliance with the permissible safety distance when travelling at a constant speed in traffic. The desired distance from the vehicle in front is set by means of the sliding switch on the stalk. Actuation of the switch increases or reduces the distance by one stage each time. The desired distance selected determines the vehicle acceleration dynamics.SSP282_059The chosen distance is briefly indicated on the info line in the speedometer centre display. The centre display is activated the first time the button is pressed. The number of bars between the vehicles displayed corresponds to the distance stage selected in each case. The distance stage can be set for each driver.Design and operation of the ACC are described in SSP 289 – Adaptive Cruise Control. Pay attention to operating instructions and manuals.SSP282_06257 Electrical SystemBus topologyThe increasing demand for additional functions and convenience in the vehicle calls for the use of ever more wide ranging electronics. The increased use of electronics also requires a new approach to data transfer between the individual control units. This also applies to the Audi A8 ´03, in which more than 70 control units have to communicate.Control unit with display in dash panel insert J285Dash panel insert CANDiagnosis CAN Drive system CANDiagnostic connection T16Electric park and handbrake control unit J540Headlight range control unit J431Airbag control unit J234ABS with EDL control unit J104Engine control unit J623Engine control unit 2 J624Adaptive suspension control unit J197Automatic gearbox control unit J217Internal bus linkAnti-theft/ tilt system control unit J529Boot lid control unit J605Wiper motor control unit J400Garage door operation control unit J530Multifunction steering wheel E221LINConvenenience system central control unit J393 On-board power supply control unit J519On-board power supply control unit 2 J520Steering column electronics control unit J527Steering angle sender G85Driver side door control unit J386Front passenger side door control unit J387Rear left door control unit J388Rear right door control unit J389Seat adjustment control unit J136Front passenger seat adjustment control unit J52158Convenience CANAdaptive cruise control CANDistance regulation control unit J428 Rear DVD changer R162 Control unit for rear right information display and operating unit J649Telephone/ telematics control unit J526BluetoothTMTelephone handset R37Control unit for rear left information display and operating unit J648Front information display and operating unit control unit J523DSP control unit J525Data bus diagnostic interface J533MOST busNavigation system control unit J401CD ROM drive R92TV tuner R78CD changer R41Digital radio R147Chip card reader control unit J676Radio module RFresh-air blower control unit J126Heated windscreen control unit J505Rear left footwell heater element Z42Rear right footwell heater element Z43Driver seat ventilation control unit J672Front passenger seat ventilation control unit J673LINClimatronic control unit J255 Rear seat adjustment with memory control unit J522 Trailer detector control unit J345 Energy management control unit J644 Entry and start authorisation control unit J518 Parking aid control unit J446Rear Climatronic control and display unit E265Tyre pressure monitor control unit J502Sun roof electronics control unit J528Additional heater control unit J364Driver identification control unit J589LINDriver side rear seat ventilation control unit J674 Front passenger side rear seat ventilation control unit J675 Sliding sun roof motor V1 Auxiliary heating radio controlled receiver R64SSP282_06359 Electrical SystemThe familiar CAN bus (two-wire bus) is supplemented by the following bus systems: – LIN bus (single-wire data bus) – MOST bus (optical data bus) – BluetoothTM (wireless data bus)LIN bus LIN stands for Local Interconnect Network. Local Interconnect means that all control units are located within a limited structural space (e.g. roof). This is also referred to as "local sub-system". Data are exchanged between the individual LIN bus systems in a vehicle by one control unit in each case using the CAN data bus. The LIN bus system is a single-wire data bus. The wire has a basic colour (violet) and a code colour. The wire cross-section is 0.35 mm2. A screen is not necessary. The system permits data exchange between one LIN master control unit and up to 16 LIN slave control units.LOCAL INTERCONNECT NETWORKDesign and operation of the LIN bus are described in SSP 286 – New data bus systems.Data bus diagnostic interface (gateway) LIN master LIN slave 1Diagnosis CANSSP282_031 Diagnostic connection 60 LIN slave 2 MOST bus The term "Media Oriented Systems Transport" signifies a network featuring media-oriented data transport. This means that, in contrast to the CAN data bus, address-oriented messages are transmitted to a specific receiver. This technique is used in Audi vehicles for the transfer of infotainment system data. The infotainment system offers a wide range of modern information and entertainment media. In addition to the familiar CAN bus systems, use has been made for the first time in the Audi A8 ´03 of an optical data bus system. The name of this data bus system is derived from "Media Oriented Systems Transport (MOST) Cooperation". This is an association formed by various motor vehicle manufacturers, their suppliers and software companies with a view to developing a standard high-speed data transfer system.RMedia Oriented Systems TransportDesign and operation of the MOST bus are described in SSP 286 – New data bus systems.System managerSound systemOperating unitSSP282_034Display 61 Electrical SystemBluetoothTM BluetoothTM is an internationally standardised remote control data interface. It permits control or monitoring of even minute units using radio waves. The primary aim when developing this new type of interface was to create a wireless alternative to cable links, which used to be susceptible to interference and inconvenient and frequently featured incompatible connectors. More and more manufacturers are making use of "BluetoothTM" radio wave technology for example for wireless interconnection of notebook and mobile phone accessories. As initiator and main contributor to the development of this new transmission technology, the Swedish company Ericsson chose the name "Bluetooth". The name originates from the Viking king Harald Blåtand II (Danish, literally meaning "Blue Tooth"), who lived around 1000 years ago in Denmark and Norway. Design and operation of the BluetoothTM are described in SSP 286 – New data bus systems.Motor vehicle applications – – – – – Wireless telephone receiver Wireless mobile phone Hands-free unit with no additional adapters Wireless internet access Access for PCs and NotepadsSSP282_037 62 Vehicle electrical system A major factor in terms of vehicle reliability is one which is never even seen: the electrical system. Use is made for the Audi A8 ´03 of a customerspecific one-piece modular wiring harness. "One-piece" means that power is supplied for all essential electrical functions from a single continuous wiring harness. The only isolating points are at the doors, roof module and engine. "Customer-specific" means that each wiring harness is designed to serve exactly the equipment ordered by the customer. The wiring harness is subdivided into individual logic modules, each of which is responsible for a clearly defined range of functions. A plastic optical fibre is fitted for the transmission of optical communication and infotainment signals. Its advantages as compared to a copper conductor are its insusceptibility to electromagnetic interference, a high transmission capacity and less weight. To achieve greater headroom, the wiring harness to the roof module has been extended to include the flexible flat cable (FFC). This represents a new method of solving the wiring problem in extremely confined spaces (max. 2 mm between headliner and body outer skin).Design and operation of the optical fibre are described in SSP 286 – New data bus systems.SSP282_038 63 Electrical SystemConvenience and security electronics"Advanced Key" entry and start authorisation system "Advanced Key" can be taken to mean an "advanced locking and security system". It takes the form of a non-contacting key recognition system. With the "Advanced Key" package, the "Vehicle unlocking" and "Vehicle locking" functions by way of a mechanical or remote control key are supplemented by the noncontacting functions "Vehicle unlocking" and "Vehicle locking". Functions Advanced Key "unlocking" The key owner enters the key detection zone next to the vehicle (less than 1.5 m from door handle) and reaches into the recessed handle moulding. A proximity sensor starts a key scan by way of an aerial. The key responds by way of radio waves and the vehicle is unlocked if authorised. Advanced Key "starting" The driver presses the start button, which again initiates a key scan via the passengercompartment aerials near the selector lever, at the rear centre vents and at the rear centre armrest. The remote control key provides confirmation, with the result that the ignition is switched on on depressing the first stage of the start button and the engine started on depressing the second stage. The engine is switched off with the STOP button. Advanced Key "locking"SSP282_094 SSP282_093Design and operation are described in SSP 287 – Audi A8 ´03 Electrical Components. In addition, the driver can start the engine with the START/STOP button (START/STOP function) without inserting the ignition key in the electronic ignition lock.If the vehicle is to be locked from the outside, it is sufficient to press the locking button in one of the door handles. Actuation of the locking button triggers a key scan via the door handle aerial and the vehicle is locked on confirmation of the remote control key.64SSP282_095 Multifunction steering wheel A new multifunction steering wheel has been introduced as standard. This is equipped with special paddles (as used in formula 1 and for the Le Mans R8) for manual shifting of the 6-speed Tiptronic®. The voice control option for radio, CD changer, telephone, navigation system and MMI address book can also be operated by way of the multifunction steering wheel.Dash panel insert display Selection menu for: – Radio station – CD track – Telephone address book – Navigation system information displayPaddle –Paddle +Menu selection controlVolume level/navigation message repetition controlMODE button SSP282_086Voice control start/termination buttonPress MODE button: For telephone, navigation system and radio/CD menu selection Turn left function control: To select menu item Press left function control: For selection within chosen menu item To accept a telephone callPress PTT (push to talk) button: To activate/deactivate voice control Turn right function control: To regulate volume Press right function control: To repeat last navigation system message65 Electrical SystemInfotainmentDVD - VideoDAB - Digital radioTelephone TelematicsCentral display and controlTV receptionCD/DVD navigationInternet Email Minidisc/CD audio SSP282_090Both in the modern business world and in the private domain, mobile information and entertainment are becoming ever more important.In other words, vehicle occupants are becoming increasingly interested in enjoying the benefits of modern media.66 With this in mind, the Audi A8 ´03 is fitted with an infotainment system offering a wide range of modern media.MemoryCD 1 Dire Straits - Brothers in …ForwardSourceTr. 12 10:56ManualTP TMC D2 PrivateSoundSSP282_096Design and operation are described in SSP 293 - Audi A8