TECHNICAL DOCUMENTATION

SSP 283 6-speed Automatic Gearbox 09E in the Audi A8 ’03 – Part 1

PDFEN72 pages5 MB
SSP 283 6-speed Automatic Gearbox 09E in the Audi A8 ’03 – Part 1 - PDF cover

This PDF is currently unavailable.

Read document text
283Service.6-speed automatic gearbox 09E in the Audi A8 '03 - Part 1 Self Study Programme 283For internal use only Speed-change gearboxes are of prime importance with regard to fuel consumption, emission levels, dynamics and comfort in the vehicle. New concepts such as automatic gearshift systems or continuously variable automatic transmission represent alternatives to the conventional multi-step automatic gearbox.For a combination of high torque transmission levels with corresponding ride comfort, the multi-step automatic gearbox remains the uncompromising option in terms of torque conversion. The new 6-speed automatic gearbox 09E represents the logical next stage in the development of the multi-step automatic gearbox concept. It sets new standards in its class as regards economy, dynamics and comfort.2 The 09E was developed and is manufactured by the renowned system supplier ZF. Together with the gearbox development specialists at Audi, the unit was adapted to the quattro drive concept and vehicle-specific requirements. The 09E is the first representative of a new 6-speed gearbox family which is to include further additions to both the top and bottom end of the torque transmission scale.The new 6-speed generation is designed to replace the familiar 5-speed 01V and 01l automatic gearboxes.3 ContentsPart 1 SSP 283GeneralTechnical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Brief description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Sectional view of gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15PageGearbox PeripherySelector mechanism. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Selector lever gate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Selector mechanism kinematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Selector lever/button kinematics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Selector lever locks/emergency release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 tiptronic steering wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 tiptronic/selection strategy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Selector lever position and gear indicator in dash panel insert . . . . . . . . . . . . . .25 Ignition key removal lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Starting lock/starter control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32Gearbox AssembliesTorque converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Torque converter clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Torque converter shift operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Torque converter oil supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Torque converter clutch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 ATF pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 ATF cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 ATF cooling with shutoff valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Oil and lubrication system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Selector elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Dynamic pressure equalisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Overlapping gearshift operations/control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Planetary gearbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Gear description/torque profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 Gearshift matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Hydraulic system diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Parking lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Torque profile/four-wheel drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Transfer case cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Transfer case oil pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70The Self Study Programme contains information on design features and functions. The Self Study Programme is not intended as a Workshop Manual. Values given are only intended to help explain the subject matter and relate to the software version applicable when the SSP was compiled. Use should always be made of the latest technical publications when performing maintenance and repair work.New NoteAttention Note4 Part 2 SSP 284Gearbox ControlPageMechatronik . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrostatic discharge ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Hydraulics module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Description of valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Electronics module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Automatic gearbox control unit J217 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Temperature monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Monitoring of oil temperature population . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 New control unit generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Description of sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Gearbox input speed sender G182 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Gearbox output speed sender G195 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 tiptronic switch F189 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Gear sensor F125. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Gearbox oil temperature sender G93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Explanation of important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 "Brake pressed" information ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 "Kick-down" information ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 "Accelerator pedal position" information... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 "Engine torque" information ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 "Engine speed" information ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Interfaces/additional signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Block diagram/system layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 CAN data exchange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Stationary vehicle decoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Engine torque intervention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Reversing light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Emergency programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Substitute programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mechanical emergency running . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Gear monitoring with symptom recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Dynamic Shift Program DSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Operational structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Driving style factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Situation-based drive program selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Gear selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42ServiceSelf-diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Snapshot memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Update programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Special tools/workshop equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Note on repair work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Cutaway model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505 GeneralTechnical dataDesignation Audi factory designation ZF factory designation Code letters 2) 09E AL 600-6Q 6HP-26 A61 GNT (V8 3.7 l) GNU (V8 4.2 l) GKY (V8 4.0 l TDI) Electrohydraulically controlled 6-speed planetary gearbox (multi-step automatic gearbox) with hydrodynamic torque converter and slip-controlled torque converter lock-up clutch Four-wheel drive with integrated Torsen centre differential and front-axle differential in front of torque converter Mechatronik (hydraulic control unit and electronic control integrated into one unit) Dynamic shift program DSP with separate sports program in "Position S" and tiptronic shift program for manual gear change Up to 650 Nm 320 kW/5800 rpmGearbox typeControlMax. torque/power transmission 2)Torque converter (2WK stands for two-lining torque converter clutch) 1) Torque converter multiplication 1) (torque increase)Hydrodynamic torque converter with controlled torque converter clutch W 280 S - 2WK (650 Nm version) W 260 S - 2WK (440 Nm version) 1.66 (GNT) 1.70 (GNU)1) 2)3)These values depend on the version concerned. Two versions are currently available: Up to 440 Nm for the V8 5V 4.2 l/3.7 l Up to 650 Nm for the V8 TDI 4.0 l and W12 6.0 l The differences in weight result from the different torque converters, clutches and planetary gear train design.6 Transmission ratios Planetary gearbox1st 2nd 3rd 4th 5th 6th Rgear gear gear gear gear gear gear4.171 2.340 1.521 1.143 0.867 0.691 3.403Primary drive Front-axle spur gear unit Front-axle bevel gear unit Rear-axle bevel gear unit i constant (front/rear axle)32Z/30Z 1.067 31Z/29Z 1.069 32Z/11Z 2.909 31Z/10Z 3.100 3.317 / 3.307 (data apply to GNU only)Spread Front/rear axle torque distribution Gear oils ATF specification6.04 Torsen centre differential type A 50/50 Lifetime fill G 055 005 A2 Shell ATF M-1375.4 G 052 145 A1/S2 (Burmah SAF-AG4 1016)Front-axle differential and transfer case specificationGear oil quantities ATF Front-axle differential Transfer case Total weight (incl. oil and ATF cooler) 3) approx. 10.4 l (fresh fill) approx. 1.1 l (fresh fill) approx. 1.1 l (fresh fill) approx. 138 kg (440 Nm version) approx. 142 kg (650 Nm version) Length (from engine flange to rear-axle flange shaft) approx. 98 cm (95 cm with 01L gearbox)7 GeneralBrief descriptionThe development aims....– Improved performance – Reduced consumption and emissions – Greater efficiency – Better weight distribution of drive system components – Less weight – High degree of gearshift spontaneity with outstanding shift comfort – Minimisation of manufacturing costs with increased reliability and durability....were implemented as outlined in the following.One of the main factors in achieving the development goals in the fields of consumption, emissions and performance was the increase in gear ratio steps to include 6 forward gears in conjunction with a greater overall spread. With a spread of 6.04, the 09E attains levels which were previously the sole domain of continuously variable transmission systems.The 6-speed planetary gearbox is based on the Lepelletier principle. This concept is characterised by harmonic gear ratio steps and the implementation of six forward gears and one reverse gear with only five selector elements.Explanatory note: The gear train configuration used here was designed some 10 years ago by the now 75-year old engineer M. Lepelletier, the owner of the patent for this design which now bears his name.8 01L / 09E transmission ratio comparisonGear 1 1 Engine speed 2 2 3 3 4 4 5 5 6V max. limitationVehicle speed 09E 01L 283_092Transmission ratio comparison / spreadTransmission ratio 01L / spread 4.44Gear09E / spread 6.04283_086Petrol and diesel engines attain maximum speed in 5th and 6th gear respectively.9 GeneralOptimisation of a wide range of details and technical concepts resulted in enhanced gearbox efficiency:– The fact that there are only five selector elements reduces the friction torque in the clutches with no power transmission. – A new, optimised gear oil with lower viscosity particularly at low gearbox temperatures reduces the friction loss. – Improved internally geared oil pump with smaller delivery volume and reduced leakage. – Optimisation of oil supply with reduced leakage in hydraulic control system.– Increase in gearing efficiency to greater than 99% through optimisation of gear trains. – Increase in permissible friction power of controlled torque converter clutch, thus extending the operating range (for more details, refer to Page 34 onwards). – The "stationary vehicle decoupling" function reduces engine output when the vehicle is stopped with a gear engaged by interrupting power transmission. In addition to reducing consumption, ride comfort is enhanced due to the fact that less braking force is required (for more details refer to Part 2 SSP 284, Page 30 onwards).01L09EEfficiency [%]Gear 283_136 10 A special feature of particular note with regard to the 09E automatic gearbox is the location of the front axle differential (flange shaft) in front of the torque converter.The distance between flange shaft and engine flange is now only 61 mm (01L = 164 mm).01L164 mm09E61 mm 283_00411 GeneralThe method of bolting the torque converter to the drive plate by means of a profiled plate meant that it was possible to move the torque converter to the rear and create space for the flange shaft. Thanks to this sophisticated concept, the entire drive unit is now closer to the centre of the vehicle. The resultant more even weight distribution between front and rear axle is of significant benefit to vehicle handling. To make optimum use of this advantage for all engine versions, various spacers are fitted between engine and gearbox to adapt each engine type to the given installation situation.Profiled plate / bolted connection to drive plate Flange shaft 283_006 Torque converter housingFlange shaft 283_157Spacers: W12 6.0 l 13 mm 4.2 l / 3.7 l with toothed belt drive 23 mm V8 TDI 4.0 l None283_111 12 The Mechatronik integrated into the gearbox housing is a new development. It combines the hydraulic control unit, sensors/actuators and electronic gearbox control unit in a coordinated assembly (for more details refer to Part 2 SSP 284, Page 4 onwards).283_007283_112All data exchange with the vehicle periphery takes place via the drive system CAN, thus reducing the number of vehicle periphery interfaces to a minimum (13 pins) and at the same time enhancing operational reliability (for more details refer to Part 2 SSP 284, Page 25 onwards).283_113 13 Transfer case oil pumpFlange shaft ATF pump Primary planetary gear train (single planetary gear train) Secondary planetary gear train (Ravigneaux gear train) Front-axle spur gear unitPrimary driveTorsen differentialFlange shaft Mechatronik Vehicle wiringharness connector Front-axle spur gear unit Permanent magnetATF heat exchangerATF filter283_00214 Sectional view of gearboxFront axle differentialATF heat exchangerFlange shaft 283_003Colour codingHydraulic components / control Planetary gear train components Shafts / gears Electronic components / control unit Multi-plate clutches, bearings, washers, circlips Plastic, gaskets, rubber, washers Selector element components, cylinders / pistons / baffle plates Housings, bolts, pins15 Gearbox PeripherySelector mechanismThe selector lever forms the mechanical link between the driver and the selector slide of the hydraulic control system. The selector lever permits "mechanical" selection of the following positions: *P = Park position for actuation of parking lock and interruption of power flow (neutral) The ignition key can only be removed in this position (for more details refer to Ignition key removal lock, Page 26 onwards). It is only possible to move out of P position with ignition switched on (for more details refer to Selector lever lock emergency release, Page 22 onwards). R = Reverse gear Reverse gear can still be engaged in gearbox emergency operation (for more details refer to Control of reversing lights in Part 2 SSP 284, Page 32 onwards). *N = Neutral position Interruption of power flow (neutral) D = Drive position Automatic gearbox drive position, automatic selection of gears 1-6 with dynamic shift program DSP (for more details refer to Part 2 SSP 284, Page 36 onwards). S = Sports program Selector lever position "S" provides drivers with a power-oriented shift program. On receiving the information "Selector lever position S", the electronic control unit moves the characteristic shift curves to higher engine speeds, thus providing a higher level of vehicle dynamics. The DSP also ensures adaption to driver inputs (driving style factor) and driving situations in position "S".Special features of "S" program: – Moving the selector lever to "S" whilst driving with the accelerator pedal held constantly in the same position results in change-down within defined limits. – To achieve more direct vehicle reaction to accelerator pedal movement, the torque converter clutch is kept closed wherever possible whilst driving. – If 6th gear is designed for overdrive in the overall transmission ratio, only gears 1-5 are selected.Note on *N and *P for vehicles with entry and start authorisation button E408 (with advanced key system) For safety reasons, the engine can only be switched off using button E408 (stop button) in selector lever position N or P.16 Comparison of D/S characteristic shift curvesThrottle valve angle [%)]The sports program significantly extends the effective shift range between economical and sporty (for more details refer to Part 2 SSP 284, Page 39 onwards).Gearbox output speed [rpm]283_152In terms of the following functions, there are interesting new aspects to the selector mechanism in the new Audi A8: – Selector mechanism kinematics – Selector lever lock – Selector lever lock emergency release – Selector lever/lock button kinematics – Ignition key removal lock283_011 283_115 17 Gearbox PeripherySelector lever gate The selector lever gate is illuminated by means of correspondingly controlled LEDs. The PC board of the selector lever gate is provided with 7 LEDs, one for each selector lever position as well as for the + and symbols of the tiptronic gate. One separate Hall sensor each controls the corresponding selector lever position LED. The appropriate Hall sensors are switched by way of the permanent magnet 1 positioned on the masking panel (for more details refer to tiptronic switch F189 in Part 2 SSP 284, Page 18 onwards).Hall sensorLEDMagnet 1Magnet 2283_009 18 Selector mechanism kinematics The installation situation in the new Audi A8 makes it possible to achieve selector mechanism kinematics involving pulling rather than pushing of the selector lever cable on "Shifting out of position P". This permits a highly flexible selector lever cable design, thus reducing the transmission of vibration to the passenger compartment and at the same time improving noise levels. Cables are capable of withstanding high tensile force. In the opposite direction however (thrust) they are highly susceptible to kinking for physical reasons. To be able to transmit the required level of thrust, selector lever cables therefore had to be sufficiently thick and thus rigid in design. A rigid selector lever cable transmits vibrations to a far greater extent than a flexible one. If the selector lever cable is subject to tension in its installation position, vibration from the drive system is transmitted to the passenger compartment and often leads to a noise nuisance. Tension-free routing of the cable is of great importance in terms of passenger compartment noise levels.283_01119 Gearbox PeripherySelector lever/button kinematics To prevent inadvertent shifting into selector lever position "S", a change has been made to the selector lever kinematics such that switching to "S" involves pressing the button in the gearstick knob. A small gear mechanism is provided in the gearstick knob to reduce the required button operating force. The locking rod is actuated by the application of pressure, which means changes have also been made to kinematics and gearstick knob assembly (refer to Workshop Manual).Locking pawl283_018283_01720 Selector lever locks (P lock + P/N lock)Locking gateA basic distinction is made between the P/N lock whilst driving/with ignition switched on and locking of the selector lever in position P with the ignition key removed (P lock). In the past, the P lock function was implemented by the steering column lock by means of a cable to the selector mechanism. On account of the new "electronic ignition/ starter switch" (entry and start authorisation switch E415) and the electrical steering column lock control element N360, there is now no cable and thus also no mechanical link. On the A8’03, the P lock function is assumed by the locking pin of N110. To achieve this, the locking gate of the selector lever and the locking pin of N110 are designed such that locking is possible both with N110 deenergised (P) and energised (N).N110 Selector lever lock magnet Locking pin Spring force / deenergised 283_051Locking pinMagnetic force / energised 283_052Spring force / deenergised 283_05321 Gearbox PeripherySelector lever lock emergency release As a result of this modified function, the selector lever remains locked in position "P" in the event of problems with or failure of the power supply (e.g. battery flat). An emergency release mechanism is provided for the selector lever lock to enable the vehicle to be moved in such circumstances (e.g. towing). Access to the emergency release mechanism is provided by removing the ashtray insert. Actuation of the rocker causes a small cable mechanism to pull the locking pin of N110 out of the P lock, overcoming the spring force.RockerCable283_016CableLocking pin 283_015 22 tiptronic steering wheelThe tiptronic steering wheel controls have been re-designed. One paddle each for change-up (+ right) and change-down (- left) is provided on the back of the steering wheel on either side. In combination with the tiptronic steering wheel, the "tiptronic" function is also available in selector lever position "D" or "S". The tiptronic function is selected by actuating one of the two one-touch paddles on the steering wheel (selector lever in position "D" or "S"). The system then switches to the tiptronic function for roughly 8 seconds. Any gear can be selected in the permissible engine speed ranges. Gears can be skipped by tapping several times, e.g. to change down from 6th to 3rd gear. Return to normal automatic gearbox operation takes place approx. 8 seconds after the last one-touch shift request. Special feature: The approx. 8 second countdown before returning to normal automatic gearbox operation is interrupted while ever cornering is detected or if the vehicle is in overrun mode. The period is extended as a function of vehicle dynamics. Switching from one-touch function to automatic mode is however implemented after 40 seconds at the latest.The steering wheel tiptronic function in selector lever position D or S is not authorised for the USA.Paddle Tip -E221 Operating unit in steering wheel PC boardE221 Operating unit in steering wheel J453 Multi-function steering wheel control unit283_020 23 Gearbox Peripherytiptronic function with multi-function steering wheelThe shift pulse of the paddles (earth signal) is evaluated in the multi-function steering wheel control unit J453 and transmitted via the LIN data bus to the steering column electronics control unit J527.J527 transmits the information via the convenience CAN to the data bus diagnostic interface J533, from where the data are transmitted to the drive system CAN and thus relayed to J217.Convenience CAN Paddle Tip Coil connector Paddle Tip +283_021E221 E389 G189 H J453 J527 Z36 58PWM LINOperating unit in steering wheel tiptronic switch in steering wheel (left- = change-down, right+ = change-up) Overheating sensor Horn plate Multi-function steering wheel control unit Steering column electronics control unit Heated steering wheel Pulse-width modulated dimming of switch illumination LIN one-wire bus systemThe Audi A8’03 is fitted as standard with a multi-function steering wheel.24 tiptronic/selection strategyThe automatic gearbox selects the next gear up before the maximum engine speed is exceeded. Change-down to the next lowest gear is implemented on dropping below a minimum engine speed. Kick-down results in change-down to the lowest possible gear. Driving off always takes place in 1st gear. In addition to permitting manual gearshift, the tiptronic function offers a further application: As positions 4, 3, 2 no longer exist (new selector lever gate with positions D and S), prevention of change-up must be selected if required using the tiptronic function (by shifting selector lever to "tip" gate). For more details, refer to tiptronic switch F189 in Part 2 SSP 284, Page 18 onwards.Selector lever position and gear indicator in dash panel insertMost gearbox control faults and malfunctions are covered by the comprehensive selfdiagnosis function. Depending on their effect on the gearbox and road safety, faults are indicated to the driver by means of an inverted segment display in the selector lever position indicator. The vehicle should be taken to an Audi Service workshop without delay to have the fault rectified.Automatic mode 283_117tiptronic mode 283_118Fault display 283_119 25 Gearbox PeripheryIgnition key removal lockMajor modifications have been made to operation of the ignition key removal lock and selector lever lock (shiftlock). On account of the new "electronic ignition/starter switch" (entry and start authorisation switch E415) and the electrical steering column lock control element N360, there is now no mechanical link between the selector mechanism and the steering column lock (cable). Release of the ignition key removal lock is controlled by the entry and start authorisation control unit J518 and implemented by the ignition key withdrawal lock magnet N376 integrated into the entry and start authorisation switch E415. The selector lever position "P" information is supplied by the gear selector position P switch F305 (mechanical microswitch). In parallel to this, the shift position is transmitted from the gear sensor F125 by way of CAN data exchange and from the automatic gearbox control unit J217 to the control unit J518. In selector lever position P, the control unit J518 switches voltage to E415, as a result of which the ignition key withdrawal lock magnet N376 cancels key locking.If the selector lever is not set to "P" in switch position "OFF", the driver is informed of this situation on opening the driver's door by way of an acoustic signal and a visual display in the dash panel insert.Please select position P283_12126 Convenience CANSelector mechanism283_120D1 E408 E415 F305 J217 J518 N110 N376Inhibitor reading unit Entry and start authorisation button Entry and start authorisation switch Gear selector position P switch Automatic gearbox control unit Entry and start authorisation control unit Selector lever lock magnet Ignition key withdrawal lock magnet (in E415)27 Gearbox PeripheryIgnition key removal lock function There are two spring-loaded locking slides with one locking pin each behind the opening for the ignition key. On inserting and removing the ignition key, the locking pins slide through the internal profile of the ignition key on both sides. In this process the two locking slides move axially in opposite directions. If the ignition key is fully inserted, the locking slides/locking pins are in basic position (as when key is not inserted).Locking pins N376Lower internal profileUpper internal profileLocking slides283_089283_094283_09328 Engaging removal lock: When the ignition is switched on (clockwise turn to pos. 1), a mechanical locking mechanism prevents axial movement of the locking plates. The locking pins are blocked and cannot follow the contour of the internal profile. The ignition key is thus locked and cannot be removed.Locking mechanism, unlocked positionActuator pinLocking mechanism, locked position-1 = 0= 1= 2=Ignition off Basic position Ignition on Starting283_09029 Gearbox PeripheryReleasing removal lock: When ignition is switched off and selector lever is set to position "P", the entry and start authorisation control unit J518 energises the ignition key withdrawal lock magnet N376 briefly. The lever mechanism of N376 then releases the locking mechanism of the locking plates and the ignition key can be removed.Lever mechanism-1 =Ignition off 0 = Basic positionLocking mechanismN376Locking plate283_095283_156 30 Removal lock emergency release In the absence of electrical system voltage or in the event of malfunction, an emergency release mechanism permits removal of the key from the switch E415. This involves pressing the release knob with a ballpoint pen, for example, in "OFF" position. The locking mechanism is thus released and the key can be removed.0= -1 = 1= 2=Basic position Ignition off Ignition on StartingEmergency release mechanism Release mechanism 283_096The entry and start authorisation switch E415 is not assigned to any particular key. In other words, E415 can be actuated by inserting various keys.An authorised key is recognised electronically by means of reader coil and transponder.31 Gearbox PeripheryStarting lock/starter control(Audi A8 ‘03) As has always been the case, the starting lock function only permits starter operation in selector lever position P or N. A new feature is automatic implementation of starter control (actuation of term. 50) by the engine control unit J623. Release for starter actuation is always transmitted by the entry and start authorisation control unit J518 to the engine control unit J623. One of the release requirements is that control unit J217 transmits the selector slide position information P or N to the control units J623 and J518. A further requirement when starting with button E408 is that the brake pedal is pressed (brake light switch F signal via separate interface to J518). The ignition key must not be inserted in E415. The gear sensor F125 detects the positions of the selector slide and relays this information to the gearbox control unit J217. The information P/N is transmitted by J217 via separate interfaces to J623 and J518 (earth signal with P/N). J217 also transmits the selector slide position information via the drive system CAN. The information is passed by means of the data bus diagnostic interface J533 to the entry and start authorisation control unit J518. This permits plausibility checking and thus diagnosis of the separate interfaces.Refer also to block diagram in Part 2 SSP 284, Page 26 onwards (general view).E408 E415 F F125 J217 J518 J533 J623Entry and start authorisation button Entry and start authorisation switch (electronic ignition switch) Brake light switch Gear sensor Automatic gearbox control unit Entry and start authorisation control unit Data bus diagnostic interface (gateway) Engine control unit32 Convenience CANDrive system CANStart release signal Signal TERM. 50 ON To starter term. 50Convenience CAN283_022OutputDrive system CANInput33 Gearbox AssembliesTorque converterTorque converter clutch Torque converters operate on the basic fluid coupling prinicple. This automatically leads to a difference in speed between pump and turbine impellers. This is referred to as converter slip, which causes a reduction in efficiency. The torque converter clutch (TCC) eliminates converter slip and thus contributes towards achieving optimum consumption. Modern torque converters have therefore been fitted with a TCC for many years. Closing and opening of the TCC is regulated in the interests of ride comfort. A basic distinction is made between three operating statuses: TCC open TCC control mode TCC closed Power transmission via the TCC used to be subject to relatively tight limits. For this reason, the TCC was only closed in the higher gears and operated on a controlled basis at low engine torques. The permissible friction power of the TCC was increased with the 09E automatic gearbox, thus considerably extending the operating range and enhancing the overall efficiency of the drive system.The TCC ... ... can be engaged in all gears ... can be engaged with any engine torque ... is engaged as of 40°C ATF temperature To achieve constant transmission of the high torque levels, the TCC has two friction surfaces. The TCC has a separate lining plate. This plate is provided on both sides with a clutch lining, thus creating two friction surfaces. The lining plate is located between the torque converter cover (converter housing) and the TCC piston. These two components are mutually friction locked. The lining plate is positively connected to the turbine impeller. On closing the TCC, the torque is transmitted from both sides to the lining plate and thus to the turbine impeller. In line with physical principles, doubling the number of friction surfaces also doubles the amount of force which can be transmitted. To ensure TCC durability and a long service life, the new ATF G 055 005 A2 was specially developed to suit the exacting requirements involved. The torque converter is matched to the power output and characteristics of the engine. In the event of complaints and when replacing the torque converter, particular attention should be paid to correct assignment to the engine/gearbox. The torque converter multiplication can be read out by way of selfdiagnosis function 08 "Reading measured value block".34 2-lining torque converter clutchWhen installing the torque converter, particular care is to be taken to ensure that the grooves of the converter hub engage in the oil pump drivers (refer to Workshop Manual).Roller bearing mountingThe mounting of the torque converter in the oil pump housing takes the form of a wear-resistant roller bearing. This design ensures a long mounting service life, particularly under operating conditions with restricted oil supply (on cold initial starting).283_013The basic mode of operation of the torque converter is explained in the Multimedia Training Programme "Power Transmission 2" (000.2700.21.20).35 Gearbox AssembliesTorque converter shift operations The torque converter multiplication is not only used for driving off, but also as a substitute for the gearshift operation under specific loads and at certain operating points. Thus for example on accelerating in certain load situations, the torque converter clutch is opened instead of change-down taking place, resulting in an increase in engine speed in a similar manner to changedown. The difference in speed between the pump and turbine impellers produces an increase in torque by the converter, corresponding to a gearshift operation, and at the same time the increase in speed causes the engine to be operated in a higher power range. Example of torque converter shift operation The advantage of this "strategy" is that "torque converter shifting" is smoother than shifting between gears on account of the damping effect of the torque converter and the relatively simple torque converter clutch control action. In conjunction with the 6-speed gearing, the additional "torque converter shift operations" provide corresponding intermediate stages and thus a level of handling approaching that attained with continuously variable transmission.Change-down characteristic curveChange-up characteristic curveExample of operating point shift (driver presses accelerator) Previous operating point Torque converter clutch open 283_10636 Torque converter oil supply The torque converter is constantly supplied with oil by means of a separate hydraulically controlled circuit. The heat (produced by the hydrodynamic torque transmission and the friction power of the TCC) is dissipated by the continuous supply of ATF. The TCC is controlled electrohydraulically by regulating the direction of flow and the pressure applied to each side of the TCC piston. TCC control is based on the following parameters: – – – – – – Engine speed Engine torque Turbine speed Current gear Output speed ATF temperature The gearbox control unit uses these to calculate the specified TCC status and establishes a corresponding control current for the pressure regulating valve N371. N371 converts an electrical control current into a defined proportional hydraulic control pressure. This control pressure regulates the torque converter pressure valve and the torque converter clutch valve, which determine the direction of flow and the pressure for the TCC.Lubrication valveNon-return valveATF coolerTo lubrication circuitTorque converter clutch valveTorque converter pressure valveSolenoid pressure control valve EDS6283_100 37 Gearbox AssembliesTorque converter clutch operation TCC_open When open, the oil pressure is equal on both sides of the TCC piston. The ATF flows from the piston chamber past the lining plate and friction surfaces to the turbine chamber. The warm ATF is routed by means of the torque converter clutch to the ATF cooler for cooling. This design ensures adequate component and ATF cooling both during torque converter operation and with torque converter clutch control action.Sch.-VRSVATF coolerWKVWDVSch.-V RSV WKV WDV= = = =Lubrication valve Non-return valve Torque converter clutch valve Torque converter pressure valveDepressurised Torque converter pressure System pressure Pilot pressure283_10038 TCC_control mode/_closed To close the TCC, the direction of ATF flow is reversed by actuating the torque converter pressure valve and torque converter clutch valve. The oil pressure in the piston chamber is dissipated. The pressure in the torque converter then acts on the turbine end of the TCC piston, thus causing the TCC to close. The clutch torque is increased or decreased in line with actuation of the valves. The following applies: – Low N371 control current corresponds to low clutch torque – High N371 control current produces a high clutch torque Adequate attenuation is provided in TCC control mode for engine torsional vibration, thus obviating the need for additional torsion dampers.Safety/substitute function in the event of failure: On exceeding a certain TCC specified pressure (control current), use is made of transmission capacity curves to check whether there is a difference between turbine and engine speed. If this is the case, a fault is stored and the torque converter clutch no longer closed. Fault display: NoneLubrication valveNon-return valveATF coolerTorque converter clutch valveTorque converter pressure valveDepressurised Torque converter pressure System pressurePilot pressure Control pressure283_101 39 Gearbox AssembliesATF pumpOne of the most important components of an automatic gearbox is the oil pump. An adequate oil supply is absolutely essential for proper operation. The oil pump takes the form of an internally geared (crescent) pump. Optimisation of the oil supply and the reduction of leakage throughout the entire hydraulic control system as well as in the gearbox meant that it was possible to have a lower oil pump delivery volume. Both internal pump leakage and oil supply system losses were thus significantly reduced.Roller bearing mounting Pressure pipe Stator shaftPinionRing gearIntake pipe283_12240 The oil pump is driven directly by the engine via the torque converter housing and hub. The mounting of the torque converter in the oil pump housing takes the form of a wearresistant roller bearing. The oil pump draws in the ATF through the filter and conveys the pressurised fluid into the hydraulic control unit, where the system pressure valve (Sys. Dr.V) regulates the required fluid pressure.The surplus ATF is returned to the intake duct of the oil pump and the energy liberated used to charge the intake side. In addition to increasing efficiency, the noise level is reduced by avoiding cavitation.Oil pump/gearbox endOil pump/engine endRing gearPinion DriverRoller bearing mounting 283_137 283_138When installing the torque converter, particular care is to be taken to ensure that the oil pump drivers engage in the grooves of the converter hub (refer to Workshop Manual).41 Gearbox AssembliesATF coolingThe ATF is cooled by means of a coolant/oil heat exchanger flanged directly to the gearbox and incorporated into the engine cooling circuit. Direct attachment of the ATF cooler to the gearbox permits more flexible adjustment of the cooling output. As there are no ATF pipes, this greatly reduces the number of possible sources of leakage. The "closed system" facilitates filling with ATF and checking of the fluid level. Operations arising due to the disconnection of ATF pipes when removing and installing the gearbox no longer apply. The ingress of dirt into the gearbox is thus minimised. The ATF cooler forms part of the scope of delivery of the gearbox. Cleaning of the cooler and oil pipes to remove contamination caused by gearbox damage is no longer necessary on replacing the gearbox.ATF heat exchanger283_04942 Coolant supply Coolant return ATF return ATF supply 283_047Transportation safeguard 283_081 283_082A transportation safeguard is required to protect the ATF heat exchanger on account of its location on the underside of the gearbox.The transportation safeguard is always to be used when handling and setting down the gearbox following removal. The gearbox is never to be set down on the ATF heat exchanger.43 Gearbox AssembliesATF cooling with shutoff valve Use is made of the shutoff valve N82 to warm the engine more quickly after a cold start. N82 is a rotary slide valve driven by an electric motor and actuated by the gearbox control unit J217 as a function of ATF temperature. Up to an ATF temperature of 80°C, the valve is closed and blocks the flow of coolant from the engine to the ATF heat exchanger. The engine heat is thus not dissipated to the ATF and the engine attains its operating temperature more quickly. In addition to heating the engine more quickly, the use of N82 enhances the heat output after a cold start.N82Installation location on V8 TDI283_108Operating settings: 80°C 80°C 75°C actuated (earth) not actuated actuated (earth) closed open closedPIN 8 on connector to gearbox 283_151ATF cooling with the shutoff valve N82 is initially only available for the V8 4.0l TDI and W12 engines.44 Design and operation N82 is supplied with voltage by term. 15 and term. 31. Sliding contacts and a small switching block with integrated switching electronics control the electric motor, which turns the rotary slide valve by means of a small gear unit. In the initial position (power being supplied, no actuation), the rotary slide is open. Application of earth to the signal input of N82 (pin 3) causes the motor (controlled by the sliding contacts and switching electronics) to turn the rotary slide through 90° into closed position. If earth is no longer applied, the motor turns the rotary slide through a further 90°, returning it to open position. The rotary slide always moves by 90° in the same direction. In the event of an open circuit in the signal wire, the shutoff valve remains open. ATF cooling is ensured should this fault occur. The shutoff valve is always closed in the event of short to earth. There is no ATF cooling and the gearbox overheats as a result.Gear unit Electric motorSliding contacts Switching block with switching electronicsRotary slide valve283_107The valve remains closed if the power supply fails during the warm-up phase (valve closed). There is no ATF cooling and the gearbox overheats as a result.45 Gearbox AssembliesOil and lubrication systemThe 09E has three separate oil systems. Separation between the ATF section for the front-axle drive/differential and the transfer case is achieved by way of double radial shaft seals. In the event of double radial shaft seal leakage, the oil escapes from the corresponding leakage oil bore. This rules out intermixing of the oils from the adjacent systems. ATF has to meet with the highest requirements in terms of gearshift quality and reliability and has a crucial influence on the coefficient of friction of a clutch/brake. In addition to lining quality and friction materials, the following factors govern the coefficient of friction: – Gear oil (grade, ageing, wear) – Gear oil temperature – Clutch temperature – Clutch slipFront-axle differential breather (inside torque converter bell housing)Planetary gearbox breatherTransfer case breatherGear oilATF 283_12746 The effect of the ATF on the coefficient of friction of the clutches and brakes is incorporated into development at the design and trial stages. It is thus logical that a special, improved ATF has been developed for the 09E. Use of the prescribed ATF is therefore a prerequisite for proper operation.The approved oils are designed to be a lifetime fill. For further information on this topic, refer to Part 2 SSP 284, Page 14 "Monitoring of oil temperature population".Double radial shaft sealLeakage oil bore283_128 47 Gearbox AssembliesSelector elementsThe selector elements (clutches/brakes) are designed to implement power shift operations under load. Thanks to the special configuration of the Lepelletier planetary gear train, shifting of the 6 forward gears and reverse gear only requires 5 selector elements. – Three rotary multi-plate clutches A, B and E – Two fixed multi-disc brakes C and D All selector elements are actuated indirectly by the solenoid pressure control valves (for further information refer to Part 2 SSP 284, Page 7 onwards). The planetary gearbox has no free-wheel. Engine braking action is provided in all gears. The multi-plate clutches A, B and E channel the engine torque into the planetary gearbox. In this process, the engine torque is supported at the gearbox housing by the multi-disc brakes C and D.B A C E Planetary gearbox output DGearbox input/ turbine shaft E A B C D 283_01448 The selector elements are closed hydraulically. This is achieved by applying oil pressure to the cylinder of the appropriate clutch/brake, thus causing the piston to compress the set of plates/discs. As the oil pressure subsides, the spring plate resting on the piston forces the piston back into its initial position.For optimum matching of gearbox efficiency to the engine, the number of clutch plates is adapted to the engine output, thus minimising the friction losses of open clutches.Clutch E Clutch piston Pressure duct to clutch E Lubricating oil ductClutch platesClutch closedShaft/planet carrier 2Turbine shaftClutch open Clutch cylinder Inner plate carrier Ring gear 1 Spring plate Outer plate carrier283_12349 Gearbox AssembliesDynamic pressure equalisation Due to the rotation at high speeds, the ATF in the clutch cylinder is subjected to considerable centrifugal force. This results in an increase in pressure in the clutch cylinder towards the largest radius. This is referred to as "dynamic pressure build-up". Dynamic pressure build-up is undesirable, as it increases the contact pressure unnecessarily and impedes defined pressure build-up and reduction in the clutch cylinder. Clutches A, B and E feature pressure equalisation to ensure reliable opening and closing of the clutches in all speed ranges. The gearshift operation can thus be precisely regulated, considerably enhancing gearshift comfort.Mode of operation taking multi-plate clutch E as an example Oil is applied to both sides of the clutch piston. This is achieved by the baffle plate, which forms a sealed chamber with respect to the piston for dynamic pressure equalisation purposes. Only low pressure from the lubricating oil duct is applied to the pressure equalisation chamber. The oil contained in the pressure equalisation chamber is subjected to the same forces (dynamic pressure build-up) as in the clutch cylinder, thus equalising the contact pressure of the clutch piston.Clutch piston Cylinder chamber Baffle plateLubricating oil ductPressure equalisation chamber Supply boreBaffle plate283_124 50 Notes51 Gearbox AssembliesOverlapping gearshift operations/control All gearshift operations (from 1st to 6th gear and from 6th to 1st gear) are so-called overlapping gearshift operations. In other words: During gearshift, the clutch in the process of transmitting power retains its transmission capacity with reduced pressure until the corresponding clutch cutting in assumes the torque being applied. The gearshift operation is assisted by a brief reduction in engine torque on changing up or an increase in engine torque on changing down (with effect from new control unit generation, refer to Part 2 SSP 284, Page 15).Engine torque interventionEngine torqueTorqueCutting-in clutchCutting-out clutchTime Torque assumption overlap 283_03252 By using overlapping gearshift operations, it is possible to effectively replace freewheeling by electrohydraulic clutch control, leading to great savings in terms of weight and space. The gearshift operations are monitored by evaluating the gearbox input speed profile (G182), enabling appropriate action to be taken as necessary (e.g. shift pressure increase, gear retention or implementation of emergency operation).Evaluation of the speed profile during the gearshift operation permits continuous adaption of the overlap control. Charging and the pressure build-up process in the clutch are influenced by appropriately adapting the control current of the pressure regulating valves. For further information, refer to Part 2 SSP 284, Page 7 onwards.Rapid charging Overlap Cutting-in clutch pressurePressureCutting-out clutch pressure Time 283_05553 Gearbox AssembliesPlanetary gearboxA new feature is the use of the so-called Lepelletier planetary gear train. This permits the implementation of six forward gears and one reverse gear employing only five selector elements (three clutches and two brakes).Principle: A single planetary gear train is fitted upstream of the Ravigneaux double planetary gear train and provides 2-speed drive for the Ravigneaux gear train. Output is always via the ring gear of the Ravigneaux gear train. A further feature is multiple utilisation of brakes and clutches.Primary planetary gear train, single planetary gear trainRing gearSecondary planetary gear train, Ravigneaux gear trainRing gearPlanet gears Planet gear Planet carrier 283_036 Planet carrier 283_126Advantages of Lepelletier planetary gear train: – The extremely compact design allows for a reduction in overall length despite a greater spread, more gear ratio steps and high torque transmission. – The use of far fewer components not only significantly reduces weight but also lowers manufacturing costs. Power flow and the different ratios of the individual gears are achieved by torque being channelled via various elements of the planetary gear trains with the other elements in each case being held stationary or two elements of a gear train being connected with one another.54 Block diagram of Lepelletier planetary gear train in the 09E gearboxTCCTo primary drive Flange shaft283_125Single planetary gear train: Sun gear (S1) Planet carrier (PT1) Ring gear (H1) = = = Stationary Clutch A/B Turbine shaft/ clutch E InputRavigneaux gear train: Large sun gear (S2) Small sun gear (S3) Planet carrier (PT2) Ring gear (H2) = = = = Clutch B Brake C Clutch A Clutch E Brake D OutputExplanation of block diagram 283_125 based on section with grey backgroundH1 S1 P1 PT1H1 P1PT1H1 P1S1S1P1 283_087P1 P1 H1 PT1 283_057 283_059 55 Gearbox AssembliesGear description/torque profilePower flow in 1st gear Selector elements: Clutch Brake A D The brake D blocks the planet carrier PT2. The torque is transmitted from the sun gear S3 to the short planet gears P3 and from there to the long planet gears P2. Supported by the planet carrier PT2, the torque is transmitted to the ring gear H2, which is connected to the output shaft.The turbine shaft drives the ring gear H1 of the primary planetary gear train. The ring gear H1 drives the planet gears P1, which roll around the stationary sun gear S1, thus driving the planet carrier PT1. The clutch A connects PT1 to the sun gear S3 and thus channels the torque into the secondary planetary gear train.In the interests of clarity, the torque profile is shown in the form of a block diagram. The following illustrations only show the upper half of the planetary gearbox in each case.P2 = 0.886 rpmH2 = 0.239 rpm PT1 = 0.657 rpmP3 = 0.849 rpmH1 = 1 rpm P1 = 1.520 rpmS1 = 0 rpmn/engineTurbine shaft = 1 rpmS2 = 0.536 rpmS3 = 0.657 rpmPT2 = 0 rpm283_070 56 Power flow in 2nd gear Selector elements: Clutch Brake A C The clutch A connects PT1 to the sun gear S3 and thus channels the torque into the secondary planetary gear train. The brake C blocks the large sun gear S2. The torque is transmitted from the sun gear S3 to the short planet gears P3 and from there to the long planet gears P2. The long planet gears P2 roll around the stationary sun gear S2 and drive the ring gear H2.The turbine shaft drives the ring gear H1 of the primary planetary gear train. The ring gear H1 drives the planet gears P1, which roll around the stationary sun gear S1, thus driving the planet carrier PT1.P2 = 0.488 rpmH2 = 0.427 rpm PT1 = 0.657 rpmP3 = 0.468 rpmH1 = 1 rpm P1 = 1.520 rpmS1 = 0 rpmn/engineTurbine shaft = 1 rpmS2 = 0 rpmS3 = 0.657 rpmPT2 = 0.295 rpm283_07157 Gearbox AssembliesPower flow in 3rd gear Selector elements: Clutch Clutch A B The clutch A connects PT1 to the sun gear S3 and thus channels the torque into the secondary planetary gear train. The clutch B also channels the torque to sun gear S2 in the secondary planetary gear train. Closing of the two clutches A and B blocks the secondary planetary gear train. The torque is then transmitted directly from the primary planetary gear train to the output shaft.The turbine shaft drives the ring gear H1 of the primary planetary gear train. The ring gear H1 drives the planet gears P1, which roll around the stationary sun gear S1, thus driving the planet carrier PT1.P2 = 0 rpmH2 = 0.657 rpm PT1 = 0.657 rpmP3 = 0 rpmH1 = 1 rpm P1 = 1.520 rpmS1 = 0 rpmn/engineTurbine shaft = 1 rpmS2 = 0.657 rpmS3 = 0.657 rpmPT2 = 0.657 rpmSecondary planetary gear train is blocked283_07258 Power flow in 4th gear Selector elements: Clutch Clutch A E The clutch A connects PT1 to the sun gear S3 and thus channels the torque into the secondary planetary gear train. The clutch E connects the turbine shaft to the planet carrier of the secondary planetary gear train PT2 and thus also channels the torque into the secondary planetary gear train. The long planet gears P2, meshed with the short planet gears P3, drive the ring gear H2 together with the planet carrier PT2.The turbine shaft drives the ring gear H1 of the primary planetary gear train and the outer plate carrier of clutch E. The ring gear H1 drives the planet gears P1, which roll around the stationary sun gear S1, thus driving the planet carrier PT1.P2 = 0.462 rpmH2 = 0.875 rpm PT1 = 0.657 rpmP3 = 0.443 rpmH1 = 1 rpm P1 = 1.520 rpmS1 = 0 rpmn/engineTurbine shaft = 1 rpmS2 = 1.279 rpmS3 = 0.657 rpmPT2 = 1 rpm283_07359 Gearbox AssembliesPower flow in 5th gear Selector elements: Clutch Clutch B E The clutch B connects PT1 to the sun gear S2 and thus channels the torque into the secondary planetary gear train. The clutch E connects the turbine shaft to the planet carrier of the secondary planetary gear train PT2 and thus also channels the torque into the secondary planetary gear train. The long planet gears P2 drive the ring gear H2 together with the planet carrier P2 and the sun gear S2.The turbine shaft drives the ring gear H1 of the primary planetary gear train and the outer plate carrier of clutch E. The ring gear H1 drives the planet gears P1, which roll around the stationary sun gear S1, thus driving the planet carrier PT1.P2 = 0.566 rpmH2 = 1.153 rpm PT1 = 0.657 rpmP3 = 0.542 rpmH1 = 1 rpm P1 = 1.520 rpmS1 = 0 rpmn/engineTurbine shaft = 1 rpmS2 = 0.657 rpmS3 = 1.420 rpmPT2 = 1 rpm283_07460 Power flow in 6th gear Selector elements: Brake Clutch C E The long planet gears P2 roll around the stationary sun gear S2 and drive the ring gear H2. Clutches A and B are open. The primary planetary gear train is not involved in power transmission.The brake C blocks the sun gear S2. The clutch E connects the turbine shaft to the planet carrier of the secondary planetary gear train PT2 and thus channels the torque into the secondary planetary gear train.P2 = 1.652 rpmH2 = 1.447 rpm PT1 = 0.657 rpmP3 = 1.583 rpmH1 = 1 rpm P1 = 1.520 rpmS1 = 0 rpmn/engineTurbine shaft = 1 rpmS2 = 0 rpmS3 = 2.226 rpmPT2 = 1 rpmPrimary planetary gear train just free-wheels283_07561 Gearbox AssembliesPower flow in reverse gear Selector elements: Clutch Brake B D The clutch B connects PT1 to the sun gear S2 and thus channels the torque into the secondary planetary gear train. The brake D blocks the planet carrier PT2. The torque is transmitted from the sun gear S2 to the long planet gears P2. Supported by PT2, the torque is transmitted to the ring gear H2, which is connected to the output shaft. The ring gear H2 is driven in the direction opposite to that of engine rotation.The turbine shaft drives the ring gear H1 of the primary planetary gear train. The ring gear H1 drives the planet gears P1, which roll around the stationary sun gear S1, thus driving the planet carrier PT1.P2 = 1.086 rpmH2 = 0.294 rpm PT1 = 0.657 rpmP3 = 1.041 rpmH1 = 1 rpm P1 = 1.520 rpmS1 = 0 rpmn/engineTurbine shaft = 1 rpmS2 = 0.657 rpmS3 = -806 rpmPT2 = 0 rpm283_07662 Gearshift matrixGear N88 P/N Reverse gear 1st gear 2nd gear 3rdgear 4thgear 5thgear 6thgearSolenoid valve logic N215 N216 N217 N218 N233 N371 AClutch logic B C D EActuation governed by operating status Actuated283_149Brake/clutch D/ETorque converter clutchSystem pressureSelector valve 1Clutch AClutch BBrake C63 HV-AHV-BHV-D1HV-D2HV-EWS Sys.Dr.V Dr.Red.V KV-C KV-D1SPVKV-BKV-D2KV-EKV-ASV1 RSVSch.V ATF cooler SV2WKVWDV283_088 64 Hydraulic system diagramDr.Red.V EDS1 (N215) EDS2 (N216) EDS3 (N217) EDS4 (N218) EDS5 (N233) EDS6 (N371) HV - A HV - B HV - D1 HV - D2 HV - E KV - A KV - B KV - C KV - D1 KV - D2 KV - E MV1 (N88) RSV Sch.V SPV SV1 SV2 Sys. Dr.V WDV WKV WSPressure reduction valve Solenoid pressure control valve 1 Solenoid pressure control valve 2 Solenoid pressure control valve 3 Solenoid pressure control valve 4 Solenoid pressure control valve 5 Solenoid pressure control valve 6 Holding valve - Clutch A Holding valve - Clutch B Holding valve - Brake D Holding valve - Brake D2 Holding valve - Clutch E Clutch valve - Clutch A Clutch valve - Clutch B Clutch valve - Brake C Clutch valve - Brake D1 Clutch valve - Brake D2 Clutch valve - Clutch E Solenoid valve 1 Non-return valve Lubrication valve Compensation valve Selector valve 1 Selector valve 2 System pressure valve Torque converter pressure valve Torque converter clutch valve Selector slideDepressurised Torque converter pressure System pressure Control pressure Pilot pressure65 Gearbox AssembliesParking lockThe parking lock is designed to stop the vehicle rolling away. It is of conventional design, i.e. it is actuated (purely mechanically) by the selector lever with a Bowden cable. The parking lock gear is connected to the ring gear 2 and the output shaft. The ratchet which engages in the toothing of the parking lock gear thus blocks output to the transfer case. Front and rear axle are locked. If one axle is raised, compensation can be achieved via the Torsen differential if the raised wheels are free to turn. This does however result in destruction of the Torsen differential when towing the vehicle, for example. To facilitate release of the parking lock, the handbrake should be applied before engaging the parking lock.Selector lever shaftLinkageTapered slide283_034Position PParking lock gearPositions R, N, D, SRatchet Tapered slide283_085 66 Torque profile / Four-wheel driveFront-axle bevel gear unit Side shaft Front-axle differential Rear-axle bevel gear unitFlange shaftTorque converter clutchFront-axle spur gear unitTorsen differentialRear-axle differentialPrimary driveTo rear left wheel Torque flow Bevel spur gearDirection of rotation/forward travelRotation in opposite direction to engine rotation Planetary gearbox To front left wheel Torque converter Parking lock gear Planetary gearbox 283_038 Rotation in direction of engine rotationParking lock gearPrimary driveA special feature of the 09E gearbox is the angled position of the input shaft (side shaft) with respect to the front axle. The torque is transmitted by a bevel spur gear (beveloid teeth) at an angle of 8° to the side shaft spur gear.Torsen differentialSide shaft Front-axle spur gear unit 283_058 67 Gearbox AssembliesTransfer case coolingTo accommodate future versions, the 09E is already designed with connections for transfer case oil cooling. For such purposes, the transfer case oil pump is not only responsible for lubricating the transfer case but also for the flow through an optional heat exchanger.Return SupplyTransfer case oil heat exchanger283_050The transfer case oil cooling diagram shown does not correspond to the final series status, as the design had still to be finalised at the time of compilation of this SSP.68 From heat exchangerTo heat exchangerWith transfer case oil coolingPressure relief valve To sump Primary drive bearing housingWithout transfer case oil coolingPrimary drive Torsen differentialHollow shaft with front-axle spur gear unitOil funnelSumpNeedle bearing Planetary gearbox housing Transfer case housing 283_14069 Gearbox AssembliesTransfer case oil pumpPrimary drive bearing housing Collector Pressure relief valveHexagonOil pump Transfer case housingSumpThe oil pump (rotor-type pump) provides efficient lubrication of all transfer case components. The pump is located in the front housing section of the transfer case and is driven by the side shaft by means of a hexagon connection. From the sump, the pump conveys the oil into a collector. The oil is routed via a duct in the primary drive bearing housing to the lower primary drive mount and some of the oil is returned to the sump. The pressure relief valve in the oil pump protects the components against excessive pressure.From the collector, the oil is conveyed in a further duct to the oil funnel, which ro