TECHNICAL DOCUMENTATION
SSP 284 6-speed Automatic Gearbox 09E in the Audi A8 ’03 – Part 2

This PDF is currently unavailable.
Read document text
ProCarManuals.com284Service.6-speed automatic gearbox 09E in the Audi A8 '03 - Part 2 Self Study Programme 284For internal use onlyContentsPart 1 SSP 283GeneralTechnical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Brief description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Sectional view of gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15PageGearbox PeripherySelector mechanism. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Selector lever gate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Selector mechanism kinematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Selector lever/button kinematics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Selector lever locks/emergency release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 tiptronic steering wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 tiptronic/selection strategy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Selector lever position and gear indicator in dash panel insert . . . . . . . . . . . . . .25 Ignition key removal lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Starting lock/starter control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32ProCarManuals.comGearbox AssembliesTorque converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Torque converter clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Torque converter shift operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Torque converter oil supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Torque converter clutch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 ATF pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 ATF cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 ATF cooling with shutoff valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Oil and lubrication system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Selector elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Dynamic pressure equalisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Overlapping gearshift operations/control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Planetary gearbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Gear description/torque profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 Gearshift matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Hydraulic system diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Parking lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Torque profile/four-wheel drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Transfer case cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Transfer case oil pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70The Self Study Programme contains information on design features and functions. The Self Study Programme is not intended as a Workshop Manual. Values given are only intended to help explain the subject matter and relate to the software version applicable when the SSP was compiled. Use should always be made of the latest technical publications when performing maintenance and repair work.New NoteAttention Note2Part 2 SSP 284Gearbox ControlPageMechatronik . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrostatic discharge ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Hydraulics module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Description of valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Electronics module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Automatic gearbox control unit J217 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Temperature monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Monitoring of oil temperature population . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 New control unit generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Description of sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Gearbox input speed sender G182 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Gearbox output speed sender G195 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 tiptronic switch F189 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Gear sensor F125. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Gearbox oil temperature sender G93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Explanation of important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 "Brake pressed" information ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 "Kick-down" information ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 "Accelerator pedal position" information... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 "Engine torque" information ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 "Engine speed" information ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Interfaces/additional signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Block diagram/system layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 CAN data exchange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Stationary vehicle decoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Engine torque intervention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Reversing light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Emergency programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Substitute programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Mechanical emergency running . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Gear monitoring with symptom recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Dynamic Shift Program DSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Operational structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Driving style factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Situation-based drive program selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Gear selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42ProCarManuals.comServiceSelf-diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Snapshot memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Update programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Special tools/workshop equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Note on repair work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Cutaway model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503Gearbox ControlMechatronikA particularly noteworthy new feature of the 09E is the so-called "Mechatronik". This combines the hydraulic control system (hydraulics module), the electronic control unit and the sensors (electronics module) in one coordinated assembly. The Mechatronik is located in the gearbox in the vicinity of the sump. Manufacturing tolerances of the hydraulics module (valves and pressure regulator) as well as of the output stages of the electronic control unit are established on a test bench and compensation is provided by way of the electronic control unit basic programming. There is no provision for basic programming as part of service work and the Mechatronik can therefore only be replaced as a complete unit.View from belowProCarManuals.comHydraulics moduleElectronics module284_007View from aboveElectronics moduleMechatronik The term "Mechatronik" covers all components responsible for Detection of input signals required for gearbox control Evaluation of input signals Implementation of control and regulation algorithms Actuation of control elements Communication with periphery and establishment of electrical and mechanical link with signal generators and control elementsHydraulics module 284_1124Advantages of Mechatronik: Less space required thanks to compact design. Low-cost manufacture due to integration of components and compensation for the manufacturing tolerances of hydraulic components by appropriate programming of electronic control unit following assembly. Lower weight due to reduction in number of pipes and housing components.Sealing element/adapter (connection to oil pump) Electronics moduleIncreased reliability thanks to great reduction in number of interfaces (contacts). Mechatronik can be calibrated and checked as one unit, thus ensuring a constant, previously unsurpassed gearshift quality.ProCarManuals.com*Valve plate *Check valve for clutches *Dampers for EDS valves*Holding valve for torque converter pressure *Valve housing Intermediate plate Connector to vehicle wiring harnessWiring harness *Hydraulics moduleConnector to electronics module 284_132 5Gearbox ControlElectrostatic discharge ESD Particular attention must be paid to ESD protection on account of the use of microelectronics and the fact that some of the electronics module interfaces are open. Before handling the Mechatronik (e.g. storage, transportation or repair), take care to discharge static by touching an earthed object or the vehicle earth when working on the vehicle. Never touch the plug contacts of the electronics module connector. The same applies to the contacts of the test adapter, e.g. when performing electrical checking. The protective cap at the electronics module connector is only to be removed immediately prior to connection of the vehicle wiring harness so as to avoid unintentional touching of contacts. The Mechatronik is always to be stored and transported in its genuine replacement part packaging. Do not remove the Mechatronik from its packaging before discharging static by touching an earthed object (e.g. water pipe, lifting platform ... ).ProCarManuals.com284_069This symbol always indicates the presence of components or assemblies in the vicinity which are susceptible to electrostatic charging. The applicable safety precautions are therefore always to be heeded.6ProCarManuals.comGearbox ControlDescription of valvesDr.Red.V Pressure reduction valve The pressure reduction valve regulates the system pressure to approx. 5 bar. This pressure (pilot pressure) is used to supply the electrically switched solenoid valves, as these require a constant pilot pressure to function accurately.HV-A HV-B HV-D1 HV-D2 HV-EHolding valve/Clutch A Holding valve/Clutch B Holding valve/Brake D1 Holding valve/Brake D2 Holding valve/Clutch EProCarManuals.comThe holding valves switch the clutch valves, i.e. the control function (control phase) of the clutch valve during the gearshift operation is deactivated by the holding valve at the appropriate time, thus causing the clutch pressure to increase to system pressure. Both valves (clutch and holding valves) are regulated by the corresponding pressure control valve.KV-A KV-B KV-C KV-D1 KV-D2 KV-EClutch valve/ Clutch A Clutch valve/ Clutch B Clutch valve/ BrakeC Clutch valve/ Brake D1 Clutch valve/ Brake D2 Clutch valve/ Clutch EThe clutch valves are variable pressure reduction valves. They are regulated by the corresponding electronic pressure control valve and determine the clutch pressure during the gearshift operation.Sch.VLubrication valveThe lubrication valve reduces and safeguards the pressure required for lubrication. It also provides an upper pressure limit.284_0798SV1Selector valve 1The function of SV1 is to maintain the current gear setting in the event of power failure whilst driving. A specific gear is accordingly selected for starting and mechanical emergency operation (solenoid valves deenergised). SV1 has a self-holding function which is cancelled on starting and re-activated by the electronic control unit. SV2 routes the system pressure to the corresponding clutch/brake controls. It is regulated by solenoid valve N88.SV2Selector valve 2SPVCompensation valveProCarManuals.comThe SPV is located in parallel to the control circuit of N88. N88 is a so-called "ON-OFF valve" which implements the corresponding setting at high speed. The function of the SPV is to cushion the increase/decrease in control pressure and provide smooth gearshift operations.Sys. Dr.VSystem pressure valveThe system pressure valve is a variable pressure limiting valve which regulates the oil pressure generated by the oil pump. It is actuated by N233. The torque converter pressure valve reduces the system pressure and maintains the pressure required for torque converter flow and for the torque converter clutch. It also provides an upper limit for the torque converter pressure to prevent operating problems. Corresponding actuation of N371 vents the oil duct to the torque converter clutch chamber.WDVTorque converter pressure valveWKVTorque converter clutch valveThe torque converter clutch valve is actuated together with the torque converter pressure valve by N371. This function involves reversal of the oil flow direction. The torque converter pressure valve (WDV) vents the torque converter clutch chamber, while the WKV applies torque converter pressure to the turbine chamber.WSSelector slideThe selector slide is actuated mechanically by the selector lever via a cable, directs the oil pressure for forward and reverse travel and provides the neutral positions.284_080 9Gearbox ControlSolenoid pressure control valves EDS 1-6 (N215, N216, N217, N218, N233 and N371) The EDS convert an electrical control current into a proportional hydraulic control pressure. They are actuated by the automatic gearbox control unit J217 and operate the valves assigned to the selector elements. Two different types are fitted: EDS 1, 3 and 6 have a rising characteristic. In other words, the control pressure increases with increasing control current. Deenergised = no control pressure (0 mA = 0 bar) EDS 2, 4 and 5 have a falling characteristic. In other words, the control pressure decreases with increasing control current. Deenergised = maximum control pressure EDS valves with rising characteristicProCarManuals.com284_130N215 (EDS1) Clutch A N217 (EDS3) Brake C N371 (EDS6) Torque converter clutchP = Pressure I = CurrentEDS valves with falling characteristic284_131N216 (EDS2) Clutch B N218 (EDS4) Brake D and clutch E N233 (EDS5) System pressureP = Pressure I = Current10Solenoid valve MV1 (N88)N88 is an electrically switched solenoid valve of the so-called 3/2 type, i.e. 3 connections and 2 switch positions (open/closed or on/ off).It is actuated by the automatic gearbox control unit J217 and its function is to provide corresponding hydraulic valve switching.ProCarManuals.com284_12911Gearbox ControlElectronics moduleThe electronics module combines the electronic control unit and sensors in one nonseparable unit.G195 Gearbox output speed senderJ217 Automatic gearbox control unitG93 Gearbox oil temperature senderProCarManuals.comG182 Gearbox input speed sender F125 Gear sensor 284_139The electronics module cannot be replaced separately. The entire Mechatronik assembly has to be replaced in the event of a component fault.G182 Gearbox input speed sender Plug connection fo EDS valvesF125 Gear sensor Plug connection for wiring harness284_13312Electrostatic discharge ESD Particular attention must be paid to ESD protection on account of the use of microelectronics and the fact that some of the electronics module interfaces are open. Refer to description and notes on Page 6.284_069Automatic gearbox control unit J217ProCarManuals.comThe electronic control unit is of the LTCC (low temperature cofiring ceramic) type and located in a hermetically sealed metal housing. The defined heat dissipation of the electronics is achieved via the ATF.The extremely compact design of the control unit makes it suitable for integration into the Mechatronik and installation in the gearbox.Temperature monitoring The fact that the electronics are integrated into the gearbox (surrounded by ATF) means that greater significance is now attached to monitoring of the control unit temperature and thus also the gear oil temperature. High temperatures have a crucial influence on the service life and proper functioning of electronic components. Temperatures above 120°C have a detrimental effect on the service life of the electronic control unit components. As of 150°C, component damage and thus malfunctioning of the entire system can no longer be ruled out. A so-called substrate temperature sensor is integrated into the substrate of the semiconductor components to record the temperature of the microprocessor (main computer of J217) as accurately as possible. Explanatory note: The term "substrate" refers to the ceramic base of the semiconductor components/ microprocessor. The substrate temperature sensor is situated directly in the substrate next to the microprocessor and records its temperature at the exact location.13Gearbox ControlMeasures are taken to prevent overheating on exceeding defined temperature threshold values (hot mode). There are 3 hot mode stages: 1st stage 124°C substrate temp. (126°C G93) In conjunction with the DSP function the shift points are moved to higher engine speeds. The operating range in which the torque converter clutch is closed is extended. For more details refer to Section on DSP, Page 36. 2nd stage 139°C substrate temp. (141°C G93) The engine torque is significantly reduced (statically, up to 60 %) as a function of the further increase in temperature. 3rd stage 141°C substrate temp. (147°C G93) The solenoid valve power supply is deactivated to prevent overheating of the control unit (malfunction, component damage). The gearbox switches to mechanical emergency running mode (refer to Page 34). Fault "17018 Temperature-related control unit deactivation" is set in the fault memory. In addition to accurate recording of component temperature, the substrate temperature sensor is used for diagnosis evaluation (plausibility checking) of the gearbox oil temperature sender G93 and provides a substitute value in the event of G93 failure.ProCarManuals.comAll temperature data are referenced to the software version 0050 applicable at the time of compilation of the SSP. The temperature data may differ for other software versions.Monitoring of oil temperature population By way of G93, the automatic gearbox control unit J217 regularly checks the current gearbox temperature range. These values are stored. Corresponding evaluation provides a long-term record of the gearbox thermal load. The service life (ageing) of the ATF is highly temperature-dependent. Sustained high ATF temperatures considerably accelerate the ATF ageing process. Gearbox damage caused by prematurely aged (used) ATF can thus be prevented by changing the ATF. If the oil temperature population reaches a defined count, the fault "18167 Multiple gear oil temperature overshoot" is set. If this fault is detected during service work, the ATF and ATF filter are to be replaced. Precise details are given in the "assisted faultfinding" routine and the appropriate Workshop Manual. Explanatory note: The term "population" refers to any group of measured values or counter data permitting statistical analysis by means of weighting and corresponding evaluation.14New control unit generation A higher performance control unit is to be introduced in the first quarter of 2003 in the course of further development. This will extend the range of functions to include: – Engine torque increase on change-down – Introduction of variant encoding This will further include extension of certain software functions such as the DSP. Further details of the new control unit generation cannot be given at present as the exact definition of the functions had not yet been finalised at the time of compilation of the SSP.ProCarManuals.comDescription of sensorsThe speed sensors and gear sensor are designed to operate on the Hall principle. Such sensors are not susceptible to mechanical wear and their signals are not affected by electromagnetic influences, thus enhancing reliability. The sensors G93, G182, G195, F125 form part of the electronics module. This cannot be replaced separately. The entire Mechatronik assembly has to be replaced in the event of a component fault. For more details on the mode of operation of Hall-type speed sensors refer to SSP 268, Page 34 onwards.15Gearbox ControlGearbox input speed sender G182 Due to the torque converter slip, the gearbox input speed does not correspond to engine speed (except when the torque converter clutch is completely closed). The electronic gearbox control system requires the exact gearbox input speed (also referred to as turbine speed) for the following functions: – Control and monitoring of gearshift operations – Control of torque converter lock-up clutch – Control of stationary vehicle decoupling – Selector element diagnosis and plausibility checking of engine speed and gearbox output speed Safety/substitute function in the event of failure: – 4th gear electrical emergency program – Pressure-modulated, controlled gear engagement – Deactivation of stationary vehicle decoupling – Opening of torque converter clutch – Deactivation of sports program "S" – Deactivation of tiptronic function Fault display: YesClutch A outer plate carrier sender wheel (connected to planet carrier PT1)ProCarManuals.comThe gearbox input speed sender G182 records the speed at the outer plate carrier of clutch A, which is connected to the planet carrier P1. The planet carrier P1 always rotates at the same ratio with respect to the turbine shaft (1 : 0.657). The speed of the planet carrier P1 can therefore be used to calculate the turbine speed (gearbox input speed).Clutch A outer plate carrier sender wheel (connected to planet carrier PT1)284_102 G182 Gearbox input speed sender284_103 16Gearbox output speed sender G195 The gearbox output speed is one of the most important electronic gearbox control signals. The gearbox output speed, with its defined ratio in relation to vehicle speed, is required for the following functions: – Selection of shift points – DSP functions (e.g. driving situation assessment) – Control of stationary vehicle decoupling (refer to Page 30) – Selector element diagnosis and plausibility checking of engine speed and gearbox input speedRing gear H2 (connected to planetary gearbox output) Sender wheel (welded to ring gear H2)Planetary gearbox output (to primary drive)ProCarManuals.comG195 Gearbox output speed senderThe gearbox output speed sender G195 records the speed at the ring gear H2 of the secondary planetary gear train. The ring gear is connected to the output shaft and there is thus a defined ratio between ring gear and vehicle speed. Safety/substitute function in the event of failure: The current gear/target gear is retained. An output speed is derived from the speed of all 4 wheels. Fault display: Yes284_105 Sender wheel (welded to ring gear H2)Ring gear H2G195 Gearbox output speed sender284_104 17Gearbox Controltiptronic switch F189 The tiptronic switch F189 is integrated into the printed circuit board of the selector lever gate. It consists of three Hall sensors actuated by the permanent magnets on the masking panel. F189 generates a square-wave signal with a fixed frequency at pins 6, 7 and 8 of the selector mechanism. In the corresponding switch setting, the voltage level is changed/ switched to positive or negative. Magnet 2 is used for continuous tiptronic switch F189 diagnosis in selector lever positions D and S. The need for this additional safety function arose from the fact that the gearbox no longer features selector lever positions 4, 3 and 2. With the new selector lever gate, prevention of change-up must be selected if required using the tiptronic function (by shifting selector lever to "tip" gate). To safeguard this function, any problems with F189 operation are now indicated to the driver even without prior tiptronic actuation.ProCarManuals.comF189 tiptronic switch (3 Hall sensors)Magnet 1Magnet 2284_009 18Safety/substitute function in the event of failure: – Deactivation of sports program "S" – Deactivation of tiptronic function (refer to note) Fault display: YesAt present, the tiptronic steering wheel function is also deactivated in position D/S. With introduction of the next control unit generation (1st quarter of 2003) it is planned to maintain the tiptronic steering wheel function in the event of F189 failure.Tip+ or Tip- signals or "tip" gate recognition at pin 5, 4 or 1 (at gearbox)Signal profile in selector lever positions D, S and DNRProCarManuals.comVoltage level Ubatt in selector lever positions P and PRNVoltage level Uapprox. 0.5 V in selector lever positions Tip+ (pin 5) or Tip- (pin 4) or gate (pin 1)DSO connection: Test prod DSO1 Test prod DSOred blackto pin 5/4/1 (at gearbox) to pin 13 (at gearbox)Conditions: Ignition ON (engine not running)284_084 19Gearbox ControlGear sensor F125 The selector lever position information is required for the following functions: – Control of starting lock (refer to Part 1 SSP 283, Page 32 onwards) – Control of reversing lights (Page 32 onwards) – Control of P/N lock (selector lever lock) (refer to Part 1 SSP 283, Page 22 onwards) – Information on driving situation (forwards/ reverse/neutral) e.g. for stationary vehicle decoupling and as information for other control units by way of bus link The Hall sensor signals are interpreted in the same way as the positions of mechanical switches. A high level signifies: Switch closed (1). A low level signifies: Switch open (0). One "switch" (Hall sensor) thus generates the two signals 0 and 1. 16 different switching combinations can be generated with 4 "switches". 5 switching combinations for recognition of selector lever positions P, R, N, D and S 4 switching combinations which are recognised as intermediate positions (P-R, R-N, N-D, D-S) 7 switching combinations which are diagnosed as not OKProCarManuals.comThe gear sensor F125 consists of 4 Hall sensors switched by a permanent magnet. The permanent magnet is actuated directly by the selector slide of the hydraulic control unit.Safety/substitute function in the event of failure: Mechanical emergency running (refer to Page 34 onwards) Fault display: YesThe gear sensor F125 indicates the position of the selector slide in the hydraulic control unit. This is used to derive the selector lever position. If the selector lever cable is not set correctly, the selector lever position does not coincide with that of the selector slide. The gear selection indicator in the dash panel insert then does not correspond to the selector lever position.To avoid misunderstandings regarding the functions of F125, it is no longer referred to in this SSP as multi-function switch but rather as gear sensor. With the 09E gearbox, F125 has no direct multiple functions.20284_008Gearbox oil temperature sender G93 G93 is integrated into the electronics module of the Mechatronik. The ATF temperature is required for the following functions: – Adaption of shift pressures (system pressure) and pressure build-up/reduction during gearshift operations – Activation/deactivation of temperaturedependent functions (warm-up program, torque converter clutch, stationary vehicle decoupling etc.) – Determination of oil temperature populationProCarManuals.com– Substitute signal for substrate temperature sender for implementation of action to reduce ATF temperature (refer to Page 13 onwards) Safety/substitute function in the event of failure: None Fault display: None284_01021Gearbox ControlExplanation of important information"Brake pressed" information ... ... is determined from switches F and F47 (refer to block diagram, Page 26 onwards). ... is supplied to J217 by way of drive system CAN by engine control unit J623 (refer to CAN data exchange, Page 28 onwards). ... is required for P/N lock and "stationary vehicle decoupling" function. The brake test switch F47 is supplied with voltage from terminal 15NL. Terminal 15NL is generated by the entry and start authorisation control unit J518. It is activated when the ignition is switched on (term. 15 normal) and remains active after switching off ignition (term. 15 OFF) until J518 receives sleep acknowledgement for the drive system CAN from the gateway J533 or until the maximum run-on time (approx. 15 minutes) has elapsed. Sensors and actuators (e.g. brake light switch) linked to control units involved in the run-on process are connected to terminal 15NL. This maintains the function and prevents misinterpretation of self-diagnosis.Safety/substitute function in the event of failure:ProCarManuals.comDeactivation of P/N lock Deactivation of stationary vehicle decouplingFault display: NoneDiagnosis evaluation:Signal statusInterpretation in control unit J217 Brake not pressedCAN information Brake not pressed Switch position Implausible Brake pressedImplausibleBrake pressedBrake pressedBrake pressed 284_14822"Kick-down" information ... ... is supplied to the engine control unit J623 by the separate kickdown switch F8. J623 evaluates the F8 switching information and transmits it to the drive system CAN (refer to CAN data exchange, Page 28 onwards). F8 also acts as accelerator pedal stop (full throttle and kickdown positions must be set accordingly).Safety/substitute function in the event of failure: Self-diagnosis can only detect a short to earth.Accelerator pedal module with accelerator pedal position senders G79 and G185ProCarManuals.comIn the event of short to earth, the kickdown signal is always applied. Kickdown takes place as a function of accelerator pedal position in line with a defined kickdown characteristic curve.F8 Kickdown switchFault display: None284_134"Accelerator pedal position" information... ... is supplied to the engine control unit J623 by the accelerator pedal position senders G79 and G185. J623 evaluates the signals and transmits the accelerator pedal position as information to the drive system CAN (refer to CAN data exchange, Page 28 onwards). ... forms an important item of information for shift point selection in addition to gearbox output speed. ... is used by the DSP function for evaluation of driving situations and driving style factor (sportiness rating). Refer to Page 36 onwards for more details on DSP. Safety/substitute function in the event of failure: Deactivation of stationary vehicle decoupling Fault display: None23Gearbox Control"Engine torque" information ... ... is supplied to the gearbox control unit by way of CAN data bus (drive system CAN). ... is used for regulation of system pressure, control of torque converter clutch and calculation of motion resistance in DSP. ... is used for calculation of torque request during gearshift operation. Safety/substitute function in the event of failure: 4th gear electrical emergency program. Pressure-modulated, controlled gear engagement. Opening of torque converter clutch. Fault display: YesProCarManuals.com"Engine speed" information ... ... is supplied to the gearbox control unit by way of CAN data bus. ... is used to control the torque converter clutch. ... is used to control stationary vehicle decoupling. Safety/substitute function in the event of failure: 4th gear electrical emergency program. Pressure-modulated, controlled gear engagement. Opening of torque converter clutch. Fault display: Yes24Interfaces/additional signalsPin assignment at connector to gearbox Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Signal for tiptronic gate/recognition (refer to Page 18) Drive system CAN-L Self-diagnosis K-wire (refer to Page 44) Signal for tiptronic change-down (refer to Page 18) Signal for tiptronic change-up (refer to Page 18) Drive system CAN-H Not used Shutoff valve N82 actuation (refer to Part 1 SSP 283, Page 44 onwards) Term. 15 P/N signal for start control (refer to Part 1 SSP 283, Page 32 onwards) P/N actuation N110 Not used Earth Term. 30 Term. 30 is required to keep drive system CAN activated until it is instructed by the gateway (sleep acknowledgement) to switch to sleep mode Not used EarthProCarManuals.comPin 11 Pin 12 Pin 13 Pin 14Pin 15 Pin 16284_15825Gearbox ControlBlock diagram / system layoutD1 Inhibitor reading unit J53 J104 J197 J217 J285 Starter motor relay ESP control unit Adaptive suspension control unit Automatic gearbox control unit Control unit with display in dash panel insert (selector lever position indicator FIS) Terminal 15 voltage supply relay Distance regulation control unit Multi-function steering wheel control unit Entry and start authorisation control unit Steering column electronics control unit Data bus diagnostic interface (gateway) Electric park and handbrake control unit Engine control unit Terminal 75x voltage supply relay Starter relay -2-E389 tiptronic switch in steering wheel E408 Entry and start authorisation button E415 Entry and start authorisation switch (electronic ignition switch) F F8 F47 F125 F189 F305 G85 G93 G182 G195 N82 N88 N110 N215 N216 N217 N218 N233 Brake light switch Kick-down switch Brake pedal switch (test switch) Gear sensor tiptronic switch Gear selector position P switch Steering angle sender Gearbox oil temperature sender Gearbox input speed sender Gearbox output speed senderJ329 J428 J453 J518 J527 J533 J540 J623 J694 J695ProCarManuals.comCoolant shutoff valve Solenoid valve 1 Selector lever lock magnet Solenoid pressure control valve -1Solenoid pressure control valve -2Solenoid pressure control valve -3Solenoid pressure control valve -4Solenoid pressure control valve -5(system pressure) N371 Solenoid pressure regulating valve -6(torque converter clutch) N376 Ignition key withdrawal lock magnet (in E415)Output InputSpecial terminals: Terminal 15NL Terminal 50R = 15 run-on (refer to Page 22) = 50 feedback, used for starter actuation feedback informationTerminal 58PWM = Pulse-width modulated dimming of switch illumination26Convenience CAN Drive system CANSignal TERM. 50 ONSignal Start releaseTo starter term. 50ProCarManuals.comDiagnosis CANV8 TDI and W12 only Signal Tip+ Signal TipSelector mechanismDrive system CANDiagnostic connectionRefer to Page 32 onwards for description of reversing light actuation functionTip- gate recognition signalRefer to Part 1 SSP 283, Page 23 onwards for description of tiptronic steering wheel operationConvenience CAN Drive system CAN Dash panel insert CANRefer to Page 28 onwards for more details on CAN data exchangeSubstrate temperature senderExtended drive system CANDiagnosis CAN284_02227Gearbox ControlCAN data exchangeJ217 Automatic gearbox control unit System status (all) Fault memory entry (10) Converter torque loss (1, 10) Gearshift active (1, 2, 10) Encoding in engine control unit (2) Current gear/target gear (1, 2, 3, 10) Selector slide position (1, 2, 3, 10) Motion resistance index (1) Emergency operation and self-diagnosis info OBD status (1) Fault memory status (10) Specified idling speed (1) Torque gradient limitation (1) (torque converter/gearbox protection) Torque converter/gearbox protection status (1) Gear selection indicator (9) Specified engine torque/gearshift (1) Gear engaged (10) CAN sleep indication (10) Torque converter clutch status (1, 10) Self-diagnosis/measured values (12)ProCarManuals.comJ428 (ACC) Distance regulation control unit (8) ACC active System status Specified accelerationDrive system CAN Extended drive system CANDiagnosis CANJ285 Control unit with display in dash panel insert (9) Tyre circumferenceDiagnostic connection (12) Dash panel insert CAN28J623 Engine control unit (1) Accelerator pedal value Kickdown Engine torque data (specified/actual) Engine speed Driver input torque Coolant temperature Brake light/brake pedal switch Air conditioner actuation Cruise control status Altitude info System status Encoding Gearbox control unit encoding Air conditioner actuationJ104 ESP control unit (2) Lateral acceleration ESP intervention TCS gearshift intervention Wheel speeds FL, FR, RL, RR System statusJ527 Steering column electronics control unit (6) J527 acts as LIN master for control unit J453 G85 Steering angle sender (4)ProCarManuals.comJ540 Electric park and handbrake control unit (3) System status GradientSteering angle Steering angle/vehicle speed System statusLIN data bus Convenience CAN J533 Gateway (10) Mileage Time, date CAN sleep acknowledgement J453 Multi-function steering wheel control unit (7) Tiptronic status Tiptronic shift request + Tiptronic shift request -J518 Entry and start authorisation control unit (5) Status and recognition of term. 15, term. 15NL, term. P, term. S, term. XJ197 Adaptive suspension control unit (11) Front and rear axle level for correction of gradient from (3)284_11429Gearbox ControlFunctionsStationary vehicle decoupling Stationary vehicle decoupling is a special feature of the 09E. With the vehicle stationary (engine idling) and a gear engaged, the torque converter already transmits a certain torque level. With the brake released, this results in the vehicle "creeping forward". With the brake pressed, the torque transmitted represents a certain loss, as the idling speed has to be kept constant by adjusting the idling torque (further opening of throttle valve). As well as increasing fuel consumption, constant brake application (a certain pedal force is required to hold the vehicle) results in a loss of comfort. The stationary vehicle decoupling function reduces the torque converter power flow to the planetary gearbox with the vehicle stationary and the brake applied ("Brake pressed" info from F and F47) by regulating the clutch A. In addition, stationary vehicle decoupling reduces the noise level with the engine idling as the engine load is lower. Stationary vehicle decoupling is not activated in reverse gear. With the current design philosophy, stationary vehicle decoupling is only activated at present in the ATF temperature range between approx. 15°C and 50°C. Functional description: Stationary vehicle decoupling is controlled by calculating the converter torque from engine and turbine speeds (speed difference). Further factors in the calculation are the ATF temperature and gradient.Stationary vehicle decoupling not active: Vehicle stationary, engine idling and turbine shaft not turning; 100 % speed difference/slip Stationary vehicle decoupling active: Vehicle stationary, engine idling and turbine shaft turning at a defined speed difference (approx. 120 rpm); slip approx. 20 %ProCarManuals.comTo ensure immediate, smooth starting, the power flow is not completely interrupted. A low converter torque level is always transmitted, thus eliminating meshing cycles and improving clutch control action. Stationary vehicle decoupling is deactivated immediately if a gearbox output speed (G195) is detected while the decoupling function is active. The power flow is established before the driver accelerates, thus largely preventing vehicle rollback on slopes. Brake release ("Brake not pressed" info) also deactivates stationary vehicle decoupling irrespective of other parameters. Exceeding a defined accelerator pedal value (with brake pressed) deactivates stationary vehicle decoupling. This permits checking of the stall speed (stall test).30As of a gradient of approx. 5 %, stationary vehicle decoupling is no longer activated. The gradient is determined by the tilt sensor of the electric parking brake EPB, which is located in the electric park and handbrake control unit J540. The gradient information is transmitted by way of the CAN bus (refer to CAN data exchange, Page 28 onwards). J540 is located in the rear right side panel (refer to information given in SSP 285 Audi A8’03 Running Gear).This has no influence on vehicle behaviour on gradients (possible rollback on releasing brake). Holding of the vehicle without the brake is still governed by idle converter torque, gradient and vehicle weight.ProCarManuals.comEngine torque intervention In addition to the familiar engine torque reduction function during change-up (negative torque intervention), the 09E is the first gearbox to offer a "positive" torque intervention feature. For greater gearshift comfort, the engine torque is increased on overrun change-down. This function will not be available at the start of series production. It is due to be introduced with the control unit generation GS1904, scheduled for calendar week 02 / 03 onwards. A precise description cannot be given at present, as the functions involved have still to be defined.31Gearbox ControlReversing lightOnboard power supply control unit (ILM/driver)ProCarManuals.comConvenience CAN (node)GatewayDrive system CAN (node)Automatic gearbox control unitGear sensor32U10 Trailer socket Trailer reversing lights Trailer detector control unit Trailer detected Deactivation of rear parking aid senders G203-G206Parking aid control unitProCarManuals.comSunroof electronics control unitY7Automatic anti-dazzle interior mirror normal positionMirror tilt down Front passenger side door control unit Mirror normal position Mirror tilt down E168 Adjustment switch for mirror with folding function Mirror normal positionDriver side door control unitConvenience system central control unit (ILM/rear)M16Left and right reversing lightsM17284_135 33Gearbox ControlEmergency programsIn the event of malfunctions, emergency programs enable the gearbox control unit J217 to prevent further gearbox damage and maintain vehicle mobility. A distinction is made between substitute programs (emergency programs) and mechanical emergency running. Substitute programs In the event of failure of a system sensor for example, the gearbox control unit attempts to form a substitute signal from the incoming information of other sensors. If a substitute signal can be formed, use is made of socalled substitute programs to maintain the gearbox functions to the maximum possible extent. If this is not possible or a safe operating status cannot be achieved, the gearbox switches to mechanical emergency running. The effect of a substitute program on vehicle handling differs greatly depending on the fault involved (refer to Description of sensors/ information). Gearbox functions may be restricted (e.g. no gearshift, no kick-down...) or implemented with fixed characteristic values (e.g. hard gearshift). Depending on importance, a fault display appears in the gear selection indicator.ProCarManuals.comMechanical emergency running Mechanical emergency running is the term used to describe the situation when solenoid valves and pressure control valves are not actuated. The power flow is controlled on a purely hydraulic basis (as a function of the position of the selector slide and hydraulic system valves) and this function is thus often referred to as hydraulic emergency running. A distinction is made between two types of mechanical emergency running: A) Control unit still active B) Control unit no longer active (total failure) The following functions remain operative in the case of mechanical emergency running with an active control unit: – Shiftlock – Diagnosis – CAN communicationFault display 284_11734Description of mechanical emergency running function – In the event of faults/malfunctions resulting in mechanical emergency running, 3rd gear is always engaged if 3rd gear or lower had previously been selected. 5th gear is selected if the gearbox is already in 4th gear or higher. – 5th gear remains engaged until either the selector lever is moved to neutral position or the engine is switched off. – A mechanical switching valve is actuated in both cases on account of the drop in hydraulic pressure. On driving off again/ restarting engine, 3rd gear is selected. – Reverse gear is available (reverse gear lock not active). – The maximum system pressure is set, thus causing maximum shift pressure to be applied to the selector elements. Hard jolts occur on engaging gear. – The torque converter clutch remains open.ProCarManuals.comGear monitoring with symptom recognition Switching to the emergency program should be avoided in the event of short-term faults during gearshift operations. If irregularities indicating gearshift problems occur in the course of a gearshift operation (e.g. on account of contamination of the hydraulic control unit), the emergency program is not selected immediately, but rather the target gear is skipped or the current gear maintained depending on the situation. The gearshift operation can be repeated several times before an entry is made in the fault memory and the emergency program thus selected. Gearbox operation is maintained to the greatest possible extent. The driver may not even notice the symptom recognition process. Symptom recognition: In the case of monitoring functions with symptom recognition, once-only recording of a fault does not immediately lead to a fault memory entry. A fault has to be detected n times. Explanatory note: Symptom "Random event; temporary characteristic"35Gearbox ControlDynamic Shift Program DSPThe DSP has been modified in the course of further development. The principal parameters used for evaluation of driving situation and driving style are basically the same as for earlier DSP generations. On account of the increasing degree of networking between gearbox control and other vehicle systems such as engine or ESP, a greater volume of data is now available to provide an even better definition of the current driving situation and driving style. This is accompanied by the substantial refinement of data processing by the gearbox control unit. As well as enhanced gear and shift point selection, the gearbox control system is now capable of implementing additional functions. The operational structure of the DSP is basically organised in three groups: – Driving style factor – Situation-based drive program selection – Gear selectionProCarManuals.com36Operational structureDriving offSESPEngine torqueKickdownLongitudinal accelerationLateral accelerationDriving style factorProCarManuals.comMotion resistance recognitionLow friction recognitionCruise controlWarm-upHigh temperatureDrive program selection Selector mechanismESP (ASC)Selector leverTip modeFast-off recognitionCornering recognitionSVFGear selection284_15037Gearbox ControlDriving style factorThe DSP constantly evaluates the current driving style with a so-called sportiness rating from economical to sporty. Evaluation of the following influences the sportiness rating: Longitudinal acceleration Longitudinal acceleration refers to the rate at which the vehicle switches from its current speed to a different speed. This incorporates both positive (acceleration) and negative (deceleration) acceleration. Lateral acceleration Lateral acceleration is the force with which a vehicle is pressed outwards when cornering. The magnitude of the force is governed by vehicle speed and steering angle. The vehicle has to exceed a defined threshold value for the evaluation function to recognise and assess high-speed cornering. The weighting with regard to the sportiness rating depends on the maximum value occurring during cornering. Evaluation of longitudinal and lateral acceleration takes place in the background and is always active (refer to Section on Gear selection, Page 42 onwards). Driving off On driving off, this function evaluates the situation by way of the maximum engine torque. Driving off from a standstill with high load application immediately results in allocation of a more sporty drive program. Kick-down If kick-down is constantly maintained, the sportiness rating is increased cyclically and this remains active for a certain period following termination of kick-down (depending on further driving style). Spontaneous increase in sportiness rating (SESP) Abrupt high acceleration (high positive accelerator pedal gradient) causes the counter to be set immediately to the maximum sportiness rating. Change-down takes place. The maximum value is only maintained for a few seconds and then returns to its initial level. Change-up takes place when acceleration is reduced.ProCarManuals.comAt present, the sportiness rating is only determined for the drive program "S". As part of conversion to the new gearbox control system it is planned to make use of the sportiness rating for drive program "D" as well.38Situation-based drive program selectionMotion resistance recognition Motion resistance recognition is one of the basic functions for drive program selection. This basic function commences as soon as the vehicle is driven off with an analysis of the equilibrium between drive power (engine torque) and the motion resistance at the drive wheels (analysis of vehicle speed and speed changes). The following factors are incorporated: – – – – Vehicle weight (and inertia) Aerodynamics (drag) Climbing resistance Rolling resistance of tyres 25 26 27 28 29 30 31 34 - 38 39 ESP1/Flat road ESP2/Hill tiptronic mode Hot mode/hill Hot mode/flat road Warm-up 1 Warm-up 2 As drive programs 4, 9, 14, 19, 24 As drive program 28 One of 15 drive programs is selected on the basis of the sportiness rating and motion resistance index. In addition to this matrix, driving situations (e.g. warm-up, hot mode) or a vehicle system (e.g. cruise control CCS/ACC) may be definitive for the selection of a special drive program.ProCarManuals.comThe end product is a motion resistance index which defines the uphill, downhill and flat road drive program.Drive programsSelector lever position "D" S0 20 15 10 5 0 "S" (S1 or S2 depending on driving style) S1 21 16 11 6 1 S2 22 17 12 7 2 Vehicle systems ACC S3 23 18 13 8 3 CCS S4 38 (24) 37 (19) 36 (14) 35 (9) 34 (4) 284_153Motion resistance index Sportiness Steep uphill Moderate uphill Slight uphill Flat road DownhillThe current drive program can be read out using the diagnosis testers in measured value block 2, 1st display value.CCS column: For technical reasons the values displayed differ from the drive programs actually used (in parentheses).39Gearbox ControlCruise control CCS or ACC mode (refer to matrix for drive programs) The function of the CCS and ACC drive programs is to minimise the gearshift frequency in the respective system mode. To further improve shift point selection in CCS/ACC mode, drive program selection was linked to the motion resistance recognition function (refer to matrix). 5 drive programs are available for each system. This permits more precise definition of the appropriate shift point and prevents repeated shifting between two gears. Warm-up program (drive programs 30 and 31) The purpose of the warm-up program is to reduce pollutant emissions after a cold start and in the warm-up phase. The warm-up program is activated at engine temperatures below 30°C. It is a static drive program, i.e. neither motion resistance recognition nor driving style factor are incorporated. All shift points are moved to higher engine speeds. Petrol engines: With petrol engines, the higher speed level achieves rapid warm-up of the catalytic converters, thus considerably shortening the response time. The warm-up program is currently not required for V8-5V engines and is therefore not implemented. Diesel engines: The higher speed level reduces the engine load and fewer pollutant emissions are produced. The engine response behaviour is also improved. At present the warm-up program is only used with diesel engines.ProCarManuals.com40Hot mode program (drive programs 28 and 29) The hot mode program is activated at high gearbox temperatures. It is basically a gearbox protection program designed to return the gearbox to a sub-critical temperature range. The significant factors governing shift point selection are temperature level and motion resistance recognition. The hot mode program is characterised by shift points at higher engine speeds and early closing of the torque converter clutch. The associated decrease in torque converter slip results in reduced warming of the ATF. The higher engine speeds ensure a greater coolant throughput in the ATF cooler and thus better cooling of the ATF. (For more details refer to Section on Temperature monitoring, Page 13)Low friction recognition (not activated at present) A basic function of the ESP is the constant determination of road surface friction. This data is now also used by the gearbox control system. In the event of low road surface friction (e.g. ice/snow, rain or non-compacted surfaces), drive programs are selected which reduce the torque at the drive wheels by way of higher gears and early change-up. Change-down which could lead to wheel slip is largely avoided.Sports program (refer to matrix for drive programs) In the sports program the driving style factor is one of the principal criteria affecting drive program selection. 10 sports programs are available depending on driving style factor and driving situation assessment (for further details on the sports program refer to Part 1 SSP 283, Page 16 onwards).ProCarManuals.comElectronic stability program intervention (drive programs 25 and 26) The action involved with various electronic stability program functions (ABS, TCS, ESP) is assisted by way of special drive programs or by gearshift prevention. Impermissible engine speeds are prevented.tiptronic mode (drive program 27) Information on this topic can be found in Part 1 SSP 283, Page 23 onwards.41Gearbox ControlGear selectionSelection of the required gear is always governed by the current drive program. Irrespective of this principle, the evaluation of sudden events or special short-term ambient conditions has a direct influence on gear selection. This evaluation generally has the effect of suppressing undesirable change-up/changedown operations and prevents repeated shifting between two gears. Fast-off recognition (rapid load reduction) This function is based on evaluation of the position and movement (highly negative pedal gradient) of the accelerator pedal and detects rapid load reduction by the driver. Rapid load reduction is very often the result of a hazardous situation in which the driver abruptly releases the accelerator pedal (fastoff) to press the brake as quickly as possible. Following detection of fast-off, change-up is suppressed until the driver presses the accelerator pedal again. Fast-off from accelerator pedal positions close to full throttle always has this effect, whereas fast-off from a part throttle position does not automatically prevent change-up. At present, fast-off recognition is only implemented in the "S program". Cornering recognition Releasing the accelerator pedal whilst cornering may lead to change-up in line with the drive program. Subsequent acceleration out of the bend then involves changing back down again (two undesirable/unnecessary gearshift operations). The cornering recognition function suppresses such undesirable change-up operations when cornering at high speed. The parameters governing this evaluation function are lateral acceleration, steering angle and wheel speed. A bend is recognised if the instantaneous lateral acceleration exceeds a defined value. The threshold is defined such that only bends negotiated in a sporty manner or incorrectly judged bends are registered.ProCarManuals.com42Spontaneous vehicle deceleration (SVF) Spontaneous deceleration is recognised by way of brake pedal actuation and corresponding slowing of the vehicle (negative longitudinal acceleration). If this is the case (only with great deceleration), the change-down point is shifted so as to implement change-down together with brake assistance at an early stage. This takes the form of change-down being advanced in closed throttle position and taking place at a higher vehicle speed than usual. The effect of the SVF function is more pronounced on long downhill stretches. The brake then only has to be pressed gently to implement change-down. The engine braking effect is put to better use by shifting the change-down points in the downhill drive program. The change-up prevention function (HSV) remains active for the duration of brake actuation or closed throttle position. Only renewed acceleration cancels HSV and results in normal change-up in line with the current drive program.ProCarManuals.comThis has the advantage that change-down is already in progress whilst the driver is still pressing the brake. The required gear is already engaged if the vehicle is then immediately to be accelerated again.43ServiceSelf-diagnosis The automatic gearbox control unit J217 and the diagnosis tester communicate by means of the K-wire or by way of the CAN data bus interface. Depending on the diagnosis tester generation used (VAG1551 or VAS 5051), data are transferred with the data log KWP 2000 on the K-wire (e.g. VAS 1551) or by means of the CAN transport protocol TP 2.0 with the data log KWP 2000 (VAG 5051). Using the CAN data bus for the transfer of self-diagnosis data is far faster than via the conventional K-wire. New, inter-system functions are now only available with CAN diagnosis. Snapshot memory The snapshot memory is used to store a wide range of gearbox control unit measured values (ambient conditions) applying at the time of the initial fault memory entry. A new feature is that these ambient conditions can be read out in the measured value block function 08 (measured value blocks 40-48). This considerably enhances the reproduction of faults and facilitates fault-finding, particularly in the case of sporadic faults (refer to "Assisted fault-finding").ProCarManuals.comThe K-wire is still required for control units of relevance to OBD.44Update programmingIntegration of the electronic control unit into the gearbox (Mechatronik) has created the means to update the software version without replacing the control unit. The control unit requires programs, characteristic curves and data (software) for the calculation of output signals. These are permanently stored in a so-called flash EPROM (erasable programmable read-only memory) and are thus always available to the control unit. The EPROMs fitted to date could not be erased or programmed when installed. To rectify problems requiring software modification, the control unit had to be replaced. The Mechatronik control unit of the 09E features a so-called "Flash EPROM". A flash EPROM can be re-programmed in situ. This process is known as "flash programming" or "update programming". Flash programming requires the use of the diagnosis tester VAS 5051 equipped as follows: – Tester software Basic CD V.02.00 or higher – Audi CD as of version V.02.22 – Current flash CD Programming is performed either by way of the diagnosis CAN interface (CAN transport protocol TP 2.0) or using the K-wire. Explanatory note: "In a flash" = "as quick as possible" In terms of "flash programming" this means "high-speed programming". The word "flash" is also used in a variety of terms relating to flash programming (e.g. flash CD). "Update" = "Bring up to date, i.e. latest status"ProCarManuals.comFlash programming is only necessary if problems can be rectified by means of software modification.45ServiceSequence of operations After inserting the current flash CD and entering into gearbox electronics diagnosis mode (address word 02), the VAS 5051 recognises whether the control unit can be programmed on the basis of the control unit identification. VAS 5051 uses the flash CD data to determine whether a new software version is available for the gearbox control unit part number concerned. If this is the case, "update programming" appears in the list of diagnosis functions. Programming commences after selecting the diagnosis function "update programming".Vehicle self-diagnosis 02 - Gearbox electronics 4E0910156 AG6 09E 4.2l5V RoW 0050 Code 00001 Dealership number 12345Select diagnosis function Supported functions 02 - Interrogating fault memory 03 - Final control diagnosis 04 - Basic setting 05 - Erasing fault memory 06 - End of output 07 - Encoding control unit Encoding sub-bus system 08 - Reading measured value block 10 - Adaption 11 - Encoding II 16 - Authorisation Challenge readout WFS iV Release WFS IVMeasurement JumpPrintHelp284_142ProCarManuals.comVehicle self-diagnosis Update programming Programming can be implemented02 - Gearbox electronics 4E0910156 AG6 09E 4.2l5V RoW 0050 Code 00001 Dealership number 12345ATTENTION Program version stored in control unit will be erased. New version xxxx will be programmed. Erasing and programming will take approx. 8 minutes. The part number in the control unit identification may change. The vehicle-specific data (encoding, adaption etc.) may be lost and may have to be updated on completion of programming. Procedure can no longer be terminated after pressing "Continue" key. Control unit may have to be replaced if ignition is switched off or diagnosis connector unplugged during programming.MeasurementJumpPrintHelpIf the update programming function is not displayed, either the flash CD is not applicable to the vehicle or the current software version already corresponds to that of the flash CD.284_14346Programming is controlled by the flash CD and takes place automatically. The programming sequence is indicated on the display, provides information on the steps in progress and issues input prompts. Programming takes approx. 5-10 minutes.Vehicle self-diagnosis Update programming Programming in progress02 - Gearbox electronics 01J927156J V30 01J 2.8l 5V RoW 1000 Code 00001 Dealership number 12345Data transferred in %284_144A programming log is displayed on completion of programming.Vehicle self-diagnosis Update programming Programming logProCarManuals.com02 - Gearbox electronics 4E0910156 AG6 09E 4.2l5V RoW 0050 Code 00001 Dealership number 12345 Extended identification new 4E0910156 AG6 09E 4.2l5V RoW 0051 Code 00001 Dealership number 12345 Unit number 128 Importer number 111Extended identification old 4E0910156 AG6 09E 4.2l5V RoW 0050 Code 00001 Dealership number 12345 Unit number 128 Importer number 111 Programming status Status Programming attempt counter Successful attempt counter Programming prerequisitesNo faults 1 1 SatisfiedMeasurementJumpPrintHelpAs CAN data exchange is interrupted during programming, faults are entered in the fault memories of the control units linked to the CAN. After progra