TECHNICAL DOCUMENTATION
SSP 285 Running Gear in the Audi A8

This PDF is currently unavailable.
Read document text
285Service.Running Gear in the Audi A8Self Study Programme 285For internal use onlyThe requirements to be met by the new A8 running gear were highly diverse and thus led to a whole series of conflicting technical aims. The remedy to these complex problems was found in the introduction of new concepts alongside progressive improvements to existing ideas and the close coordination of all sub-systems.This approach meant that it was possible to raise the high level of active road safety of the predecessor model still further and thus to again set new standards in the luxury segment.ContentsPage Front AxleSummary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Rear AxleSummary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Wheel AlignmentGeneral procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Front axle settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Rear axle settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Steering SystemSummary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Electrical steering column lock (ESCL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28Brake SystemSummary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31Electromech. Parking BrakeSummary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Operation and display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Electromechanical parking brake CAN data exchange . . . . . . . . . . . . . . . . . . . . . .45ESPSummary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48Tyre Pressure Monitoring SystemSummary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Tyre pressure monitoring system CAN data exchange . . . . . . . . . . . . . . . . . . . . . .56Run Flat System - PAXSummary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58The Self Study Programme contains information on design features and functions. The Self Study Programme is not intended as a Workshop Manual. Values given are only intended to help explain the subject matter and relate to the software version applicable when the SSP was compiled. Use should always be made of the latest technical publications when performing maintenance and repair work.New!Attention! Note!3Front AxleSummaryThe new A8 is fitted with the familiar four-link front axle (refer to SSP 161). A significant new feature is the air suspension in combination with electronically controlled dampers (refer to SSP 292). All axle components are new on account of the geometric and kinematic modifications as compared to the predecessor model, as well as the air suspension and the weight reductions achieved. Wherever technically feasible, use is made of identical components for the VW Phaeton and Audi A8.Mounting bracketUpper link Wheel bearing housingSuspension/damper strutWheel bearing Wheel hubSubframe Anti-roll bar Subframe bushes (4x) Track control link Anti-roll bar connecting link Guide linkVW Phaeton / Audi A8 identical components 285_0014System componentsWheel bearing housing The wheel bearing housing is a forged aluminium component. The guide and track control link mounts take the form of press-fit zinc-iron coated bushes.Wheel bearing housingLink mounting bushes285_002Wheel bearing Use is made of a 2nd generation wheel bearing (flange bearing). A Ø 92 mm bearing is employed for all engines. The wheel speed sensor ring forms part of the wheel bearing (refer to ESP).Wheel hubWheel bearing285_076 5Front AxleMounting bracket The mounting bracket is made of Poral cast aluminium. It is bolted to the body and designed to support the upper transverse links and the spring/damper unit.Pay attention to body bolted joint tightening sequence! (refer to current Workshop Manual).285_003Links The upper and lower links are made of forged aluminium. To minimise road noise and tyre vibration, the guide link is connected to the subframe by means of a large hydraulically cushioned bush.Heed installation positioning! (refer to current Workshop Manual).285_0046Spring/damper unit Details of the design and operation of the air suspension system components can be found in SSP 292.285_0777Front AxleSubframe The subframe takes the form of a welded stainless steel shell. To increase rigidity, the U-shape is completed by a bolted cross member at the rear.Engine supportSubframeCross member 285_005Engine support A new feature is an engine support bolted to the front attachment points of the subframe.8Anti-roll bar For weight-saving reasons, the vehicle is fitted with a tubular anti-roll bar. The anti-roll bar joins the two track control links by way of connecting links. A new development is the method of mounting the anti-roll bar at the engine support. The bushes are vulcanised onto the tubular bar and can no longer be replaced separately when performing service work.285_006285_007All mounting elements are to be attached in basic level setting ("Automatic" mode, refer to SSP 292).9Rear AxleSummaryThe rear axle is a more advanced version of the familiar A8' 02 trapezium-link axle. All axle components are new on account of the geometric and kinematic modifications as compared to the predecessor model, as well as the air suspension and the weight reductions achieved. Wherever technically feasible, use is made of identical components for the VW Phaeton and Audi A8.Subframe Upper transverse linkAnti-roll bar connecting linkTrapezium link Wheel hub Anti-roll bar Wheel bearing Link connecting rod Track rodVW Phaeton / Audi A8 identical components285_00810Principal new features compared to A8 `02 – Use of air suspension in conjunction with electronically controlled damping – Aluminium subframe to help reduce weight – Joint arrangement of spring and damper at upper transverse link – Connection of anti-roll bar to trapezium link – Use of modified track rod to reduce change in toe on compression and extension of suspension – Use of ball studs to connect wheel bearing housing and track rod, thus reducing secondary spring rate – Use of slotted bonded rubber bushes in upper transverse link and connection between trapezium link and subframe11Rear AxleSystem componentsWheel bearing housing The wheel bearing housing is made of gravity die cast aluminium.Wheel bearing Wheel hub Wheel bearing housingWheel bearing and wheel hub Use is made of a Ø 85 mm 2nd generation wheel bearing (flange bearing). The wheel speed sensor ring forms part of the wheel bearing (refer to ESP).285_009Trapezium link The trapezium link is made of sand cast aluminium. It acts as lower connecting element between wheel bearing housing and subframe. The anti-roll bar connecting link is now attached to the trapezium link. The subframe mount takes the form of an asymmetrically split bush. This helps to enhance self-steering action in the event of load changes (e.g. braking and cornering).Split bush285_010Upper transverse link The transverse link is a forged aluminium component. It forms the upper connection between wheel bearing housing and subframe. Body support at the transverse link is provided by the suspension strut. This is the first time new mounting elements have been used by Audi. The bonded rubber bushes are axially slotted to enable them to absorb great axial forces with minimum deformation. They nevertheless retain their torsional flexibility and the link can thus turn without any great resistance.Suspension/damper strut attachmentSlotted bush 285_011Refer to current Workshop Manual for information on Disassembly/Assembly.12Subframe For the first time use is made of an aluminium subframe, thus achieving a weight reduction of approx. 9 kg as opposed to a steel construction. Mounting at the body is provided by four identical hydro-bushes.The bushes have a specified installation position in the subframe (refer to current Workshop Manual)!285_012Anti-roll bar The anti-roll bar is mounted at the subframe and attached to the trapezium links by means of connecting rods.285_013285_01413Wheel AlignmentGeneral procedureThe basic principles of wheel alignment and adjustment have been retained. Main changes over A8 `02 – The toe constant is now set in vehicle basic position (B=1). – Balancing out of front axle toe values involves adjusting subframe together with engine support. – On vehicles with adaptive cruise control, the distance sensor has to be checked/ adjusted after changing rear axle toe values."Automatic" mode must be set shortly prior to wheel alignment. Vehicle must be at a settled level at the start of wheel alignment. For details, refer to wheel alignment computer user prompting.Front axle settingsAs in the past, individual toe values and the toe change profile on suspension compression/extension (= "toe-in curve") can be set for the four-link front axle. The camber values can be balanced out between the right and left side of the axle. This is achieved by moving the subframe sideways together with the engine support (for detailed information, refer to current Workshop Manual).285_078 14Rear axle settingsThe camber is set by means of an eccentric at the transverse link/wheel bearing housing bolted joint. The toe is set at the track rod/subframe bolted joint. (For detailed information, refer to current Workshop Manual).Eccentric bolt for setting camberEccentric bolt for setting toe 285_07915Steering SystemSummaryCustomers can choose between mechanical and electrical steering column adjustment, as well as between power steering and Servotronic.Principal new features compared to A8 `02 – Electrical steering lock – Spindle-driven electrical steering column tilt adjustment – Rigid track rods – Variable steering ratio – Servotronic II – Larger steering mechanism piston diameter – More detent positions at steering column splinesSystem componentsSteering pump Use is made for all petrol engines of the FP6 vane pump with a delivery volume of 15 cm3 per revolution. The maximum system pressure is limited to 125 bar. For all diesel engines, use is made of the FP4 vane pump with a delivery volume of 11 cm3 per revolution. The maximum system pressure is again limited to 125 bar.285_08016Steering mechanism Design: The rack and pinion steering mechanism essentially consists of a rack and pinion with mounting elements, piston and rotary slide valve.285_017Principal differences compared to A8 `02 – Manufacturing the rack splines with different modules and meshing angles permits variable translation of steering wheel movements into rack travel. This variable ratio achieves a more direct response with larger steering angles. – The piston diameter was increased from 43 mm to 45 mm on account of the higher axle load on vehicles fitted with the full range of equipment. – The rotary slide now has 10 grooves instead of 6, thus increasing the number of helices at the rotary slide. This produces a larger cross-section for the flow of fluid and lowers the sound level by reducing flow noise.Rack travel per steering wheel turn [mm]Steering wheel angle 285_01817Steering SystemA torsion bar in the rotary slide valve is directly connected to the steering column shaft by way of a universal joint. The upper end of the torsion bar is rigidly linked to the rotary slide by means of a pin connection. The lower end is pinned to the rack pinion and pilot bushing. Driver-induced steering motion causes a force to act on the torsion bar. The torsion bar is turned (= twisted) in a manner comparable to anti-roll bar torsion at an axle subjected to one-sided suspension compression.The rotary slide is turned together with the torsion bar relative to the pilot bushing. This results in a change in the relative positions of the grooves and bores in the rotary slide and pilot bushing. Specific fluid ducts can thus be opened and others closed depending on the angular offset between rotary slide and pilot bushing.Torsion barPin connection Rotary slidePilot bushingRack pinion285_01918Neutral position If force is not being applied to the steering wheel, the operating cylinder and pressure pipe are connected to the fluid reservoir and no pressure is built up in the system.285_021In the interests of clarity, the rotary slide is illustrated with 6 instead of 10 grooves.19Steering SystemLeft wheel lock Turning the steering wheel to the left causes the torsion bar and rotary slide to be turned on account of the resistance exercised by the tyres and road surface to turning. This action opens up a fluid duct from the pressure pipe to the right operating cylinder. The left operating cylinder is connected to the return pipe to the fluid reservoir. The piston is subjected to a force acting in the direction of left wheel lock. The rotary slide continues to turn until the total piston and steering force is sufficient to move the wheels to left lock. The associated movement of the rack pinion also causes the lower part of the torsion bar to be turned with the pilot bushing. This movement is maintained until there is no longer any turning of the torsion bar and thus no angular offset between the rotary slide and the pilot bushing (= neutral position). The return pipe to the fluid reservoir is re-connected to the operating cylinders and pressure pipe and the system is virtually depressurised again. Each time force is applied to the steering wheel, the torsion bar is turned and the above-mentioned sequence is implemented again.285_08120In the event of forces acting in the opposite direction, e.g. as a result of an uneven road surface, the power steering has a cushioning effect. This results in turning of the torsion bar due to the force of the rack acting on the pinion and torsion bar.The rotary slide and pilot bushing are turned towards one another out of the neutral position. Fluid under pressure is then conveyed to the operating cylinder chamber, where it counteracts the rack movement.285_022Example: A bump in the road exerts force FA on the front wheels, causing the wheel to turn about point D (to the right). The resultant force at the rack (FZ) causes the pinion and torsion bar to turn. The fluid supply to the right cylinder side is then opened up and the left side is connected to the return. The reaction force FR at the piston and rack equalises the action of force FZ and thus prevents turning of the wheel.21Steering SystemServotronic solenoid valve N119 The solenoid valve acts as electrohydraulic converter for implementing the Servotronic function. It is of the proportional type and open when deenergised. The higher the current level actuating the valve, the smaller the opening cross-section.285_023Servotronic operation The higher the vehicle speed, the lower the force which has to be exerted by the driver on the steering wheel when changing direction. This basically applies to all steering systems (with and without servo action). Certain compromises therefore have to be made when designing the steering. It is important to avoid an impression of overlight steering at high vehicle speeds. This is remedied by Servotronic. The Servotronic regulates the actuating torque at the steering wheel as a function of vehicle speed. The maximum servo action is provided when the vehicle is stationary or moving very slowly (e.g. when parking).Pressure p (bar)Actuating torque (Nm)120 km/h 50 km/hLow vehicle speed (e.g. when parking)285_02522The Audi A8 `03 is fitted with the newly developed Servotronic II. This again operates on the active hydraulic reaction principle. The reaction piston is located above the pilot bushing. The piston is connected to the rotary slide and thus also to the torsion bar and is supported by way of balls on the centring element linked to the pilot bushing. When the steering wheel and thus also the torsion bar are not being turned, the balls are located in a guide collar. Fluid is applied to the chamber above the reaction piston. The force exerted by the reaction piston on the balls and thus on the pilot bushing varies in line with fluid pressure.The higher the fluid pressure, the greater the force applied and thus the higher the actuating torque to be exerted by the driver on the steering wheel. The pressure control element is the Servotronic solenoid valve N119. The valve is actuated by the onboard power supply control unit -2- J520. The input signal for the control unit is the vehicle speed signal from the ESP control unit J104. The larger the opening cross-section of the valve, the smaller the drop in pressure at the valve and thus the higher the pressure in the chamber above the reaction piston. Different characteristic curves for steering wheel actuating torque and steering system pressure are thus obtained depending on vehicle speed.In addition to its actual function, the method of operation of the Servotronic II offers two further advantages: – The guide collar for the balls provides additional steering centring. Straight ahead stability is enhanced particularly at high speeds. – Fluid pressure and volumetric flow rate are not reduced. This ensures that there is always a safety margin for dealing with emergency situations (e.g. in the event of abrupt, unforeseeable steering correction).From control unit J104Control unit J520 Torsion barSolenoid valve N119Reaction pistonBallsCentring element285_02423Steering SystemSteering column As regards basic design, there is no difference between the principal components of steering columns with mechanical and electrical adjustment. Both are equipped with the electrical steering lock. The steering wheel mounting splines now have 72 detent positions instead of 6.285_026Steering column with mechanical adjustment The steering column is fixed in position by means of two sets of plates with eight steel plates each. Four plates each permit axial adjustment. The recesses in the plates for adjustment are arranged axially. The other four plates on each side are arranged vertically and permit vertical adjustment. Clamping is achieved by two rollers which run up a ramp on a cam plate during the locking process. The lever is fixed in position by an overcentre spring.EccentricLever285_02724Steering column with electrical adjustment Axial adjustment The electric motor with gear unit and spindle is permanently connected to the box rocker. The guide box with steering unit is permanently connected to the adjuster. The spindle is screwed into the internal thread of the adjuster. The rotation of the spindle is converted into axial movement of the adjuster with guide box and steering unit. A Hall sensor in the electric motor measures the number of revolutions. The control unit uses this information to determine the current position in the steering column adjustment range.Electric motor with gear unitBracket Box rockerSpindle AdjusterSteering unitGuide box285_02825Steering SystemVertical adjustment The box rocker with guide box and steering unit is swivel-mounted in the bracket. The electric motor with flexible shaft, spindle and gear unit is permanently connected to the box rocker. A threaded bush into which the spindle engages is mounted in the bracket. Rotation of the spindle produces vertical movement of the threaded bush. The rocker with guide box and steering unit is turned about the joint pivot point. The other end of the spindle is permanently connected to a spur gear. A toothed belt transmits the rotation to a spindle on the other side of the steering column, where adjustment takes place with identical components. The two-sided mounting system provides far more rigid attachment of the steering column. A Hall sensor in the electric motor measures the number of revolutions. The control unit uses this information to determine the current position in the steering column adjustment range.Bracket Guide boxPivot pointElectric motor Threaded bush Spindle Flexible shaft 285_029Threaded bushSpur gear Toothed belt Spindle 26 285_030Steering column adjustment: Block diagram Following initial assembly, the end positions are approached in Z (vertical adjustment) and X (axial adjustment) directions. These values are stored in the onboard power supply control unit J519. Each time any further adjustment is made, the Hall senders record the number of revolutions of the corresponding adjustment motor. The control unit J519 uses these values and the stored end positions to determine the current position of the steering column in the adjustment range.Switch for steering column adjustment ± Z, ± XSteering column electronics control unit J527Hall sender for steering column position ZMotor for steering column adjustment ZOnboard power supply control unit J519Hall sender for steering column position XMotor for steering column adjustment XConvenience CAN Discrete wire285_031 27Steering SystemElectrical steering column lock (ESCL) SummaryThe A8 `03 is the first Audi vehicle to be fitted with an electrical steering column lock. Significant advantages have been achieved by installing the ESCL unit and the locking mechanism at different locations: – Passive vehicle safety: Space for additional knee guards – Anti-theft protection: Components less accessible – Costs: Arrangement of control unit, motor and gear unit in one assemblyDesign: The detent wheel with bevelled outer splines is connected by means of a friction clutch to the steering column tube. The axially adjustable locking slide with bevelled inner splines is mounted in the guide box. The electric motor drives the spur gear by means of worm gearing. The axially adjustable reversing lever is mounted in the ESCL unit and linked by way of the connecting rod to the locking slide.Locking slide Detent wheel Guide box Steering column tubeElectric motorConnecting rodReversing leverSpur gear285_03228Operation: Actuation of the motor turns the spur gear. The side face of the spur gear takes the form of a ramp. The reversing lever runs on this ramp and is axially adjusted in line with the position of the spur gear and ramp position. The movement of the reversing lever is transmitted directly to the locking slide. Meshing of the locking slide and detent wheel mechanically locks the steering column.The ESCL unit is connected to the steering column by way of shear bolts and can only be replaced together with the steering column. For information on operation and electrical function refer to SSP 287 Control Units.Service: The ESCL function can be checked with VAS 5051 using the control element test. Matching is performed with the adaption function.For details, refer to current Workshop Manual and assisted fault-finding.29Brake SystemSummaryUse is made of two new brake systems: A 16-inch system for 6-cylinder engines and a 17-inch system for all larger engines. The principal new feature is the electrically actuated parking brake.Front axle Engine Min. wheel size Type of brake V6 engines 16" 16" FNRG 60 Aluminium floating frametype caliper V8 engines 17" 17" 2FNR 42 AL Two pistons Aluminium floating frametype caliper 2Rear axle V6 engines 16" 16" C II 43 EPB Aluminium floating caliper V8 engines 17" 17" C II 43 EPB Aluminium floating caliperNumber of pistons Piston diameter (mm) Brake disc diameter (mm)111602 x 42434332336028031030System componentsFront axle brake caliper A new design principle has been employed (floating frame type FNR). In this case the floating caliper is designed as a frame, thus permitting a considerable reduction in material thickness at the caliper bridge. For the first time it was possible to integrate a brake disc of 360 mm diameter into 17" wheels. In the past, 18" wheels were required for this brake disc dimension.285_034Caliper bridge HolderRim Øsc DiØFNRim Øsc DiØFNDisc Ø FNR285_035Comparison of technologies: FN and FNR disc brake in the same wheelRear axle brake caliper Use is made of an advanced aluminium floating-caliper brake. Brake disc diameter and pad area were enlarged to adapt them to the front brake dimension. This resulted in greater braking power and a longer pad service life. Corrosion resistance was improved by the introduction of stainless steel pad springs and greater pad clearance in the pad guides. Further details were modified to optimise noise level, braking comfort and environmental compatibility. The caliper concept was designed for use with the electromechanical parking brake.31Brake SystemBrake servo Use is made of a tandem vacuum-type brake servo (8+9 inch, basic design as for A4 and A6). In comparison to the A4 and A6, the transmission ratio has been increased to 7:1. The inlet valve flow characteristics have been optimised and the valve closing distance shortened. This results in far quicker and more precise servo response accompanied by a greatly improved operating feel. With V8 petrol engines, vacuum is supplied by a suction jet pump driven by the intake manifold vacuum. An electric vacuum pump is employed for the V6 petrol engine. Brake master cylinder Use is made of a tandem brake master cylinder. As compared to the A4 and A6, the piston diameter was increased to 26.99 mm with a total stroke of 36 mm (18/18). The central valves of both brake circuits (diagonal configuration) have been designed for optimum flow. This permits the use of a self-priming ESP unit without a separate charging pump. These changes and the above-mentioned modifications to the brake servo result in a significant reduction in pedal travel prior to brake response in conjunction with less pedal force. Active safety is thus enhanced by shortening the stopping distance.Brake fluid reservoir The brake fluid reservoir is a separate component fitted into the brake master cylinder. For design reasons, the brake fluid reservoir is never to be completely drained, as this would permit the ingress of air into the pipes on account of the position of the connections. Refer to the current Workshop Manual for procedure for changing brake fluid.Brake fluid reservoirBrake servoBrake master cylinder285_036 32Notes33Electromech. Parking BrakeSummaryRight parking brake motor V283Electromechanical parking brake control unit J540Parking brake pressure switch F234Left parking brake motor V282Control unit with display in dash panel insert J285 285_091 34Operation and displayThe parking brake is actuated by the pressure switch F234 in the centre console. The brake is applied by pulling the switch. It is released by pressing the switch and at the same time pressing the brake or accelerator pedal.The electromechanical parking brake can still be applied by pulling the switch even when the ignition is off. The ignition must however be switched on for the brake to be released.285_041Application of the parking brake is indicated by the parking brake display in the dash panel insert and a lamp in the switch.Parking brake display 285_042 35Electromech. Parking BrakeSystem componentsControl unit J540 The control unit is fitted beneath the battery on the right side of the luggage compartment. From the battery, the left and right parking brake motors V282/283 are actuated separately. There are two processors in the control unit. Release decisions are taken by both processors. Data transfer is by way of the drive system CAN (refer to "Data transfer"). The control unit contains an integrated micromechanical tilt angle sensor.285_043Parking brake motors V282/283 Design: The brake pads are mechanically tensioned by way of a spindle mechanism. The thread on the shaft is self-locking. The spindle is driven by a swash plate mechanism. The mechanism is driven by a DC motor. The mechanism and motor are flanged to the brake caliper.285_07236Operation: Implementation of the parking brake function involves translating the rotation of the drive motor into a very short brake piston stroke. This is achieved through the use of a swash plate mechanism in conjunction with the spindle drive. There are three transmission stages. The first reduction stage (1:3) is achieved by the motor/gear mechanism input toothed belt drive. The swash plate mechanism is responsible for the second stage. A speed reduced by a factor of 147 with respect to the electric motor drive speed is available at the gear mechanism output.Toothed beltToothed beltGear mechanismElectric motor 285_04437Electromech. Parking BrakeA spindle which drives the brake piston is responsible for converting the rotation into a stroke. The spindle is driven directly by the swash plate mechanism. A cylinder is mounted such that it can slide axially in the brake piston. Two plane surfaces stop the cylinder turning. The flared section at the end of the cylinder is provided with a forcing nut. Rotation of the spindle moves the forcing nut on the spindle thread. The number of motor revolutions is measured by a Hall sensor. This enables the piston stroke to be calculated by the control unit.Brake pistonSpindleCylinderBrake disc 285_045Parking brake application: The nut moves forwards on the spindle. The cylinder makes contact with the piston. Cylinder and piston are pressed against the brake disc.Parking brake release: The nut is screwed back on the spindle, thus relieving the load on the cylinder. The recovery of the sealing ring moves the piston back and releases the brake disc.285_046 38Mode of operation of swash plate mechanism A wheel (swash plate) with bevelled splines is mounted on the input gear. It is mounted obliquely with respect to the input gear shaft. This causes the plate to wobble as the input gear rotates. The plate is fixed in position by keyways in the gear housing. It cannot turn freely.Electric motor Output gearSwash plateToothed beltInput gear 285_047The swash plate has 51 teeth, the output gear 50 teeth. As a result of this so-called "pitch error", the swash plate teeth always make contact with the flanks of the output gear and never coincide with the tooth spaces. Consequently, the output gear is moved on by a small angle of rotation.Swash plate285_048 39Electromech. Parking BrakePosition 2 Swash plateTwo output gear teeth are meshed with two swash plate teeth in the course of one revolution of the input gear. The wobble causes the second pair of teeth (position 2) to be meshed after half a revolution of the swash plate. In position 1, the output gear is moved on such that the tooth of the swash plate again makes contact with an output gear flank in position 2. As a result of this sequence, each half revolution moves on the output gear and the spindle connected to it by half a tooth face width.Position 1285_049FunctionsThe following functions are provided by the electromechanical parking brake: – – – – Parking brake function Dynamic emergency braking function Adaptive starting-off assistant Brake pad wear recognition and play correctionParking brake function The tensioning force set by the system is sufficient for all driving situations. A text message in the dash panel insert centre display warns the driver in the event of gradients exceeding 30 %. Activated status is indicated by lamps in the switch and dash panel insert. The brake is automatically re-tensioned if the disc cools down after parking the vehicle. For this purpose, the current disc temperature is constantly established by way of a simulation model in the control unit.40Dynamic emergency braking function Pulling the parking brake pressure switch F234 slows the vehicle at a maximum deceleration rate of 8 m/s2. Operation corresponds to that of the handbrake lever. The vehicle is braked as long as the switch is pulled. Braking action is terminated on releasing the switch. If the vehicle is travelling at a speed of more than 8 km/h, braking is implemented by the ESP. With the accelerator pedal still pressed, engine torque is reduced to idling level and brake pressure is built up by the ESP assembly at all four wheel brakes. The cruise control system is deactivated if in operation. Actuation of the switch at vehicle speeds below 8 km/h causes the parking brake to be applied. To prevent possible incorrect operation (triggered for example by the front passenger), active emergency braking function is deactivated as soon as the accelerator is pressed again.Activation of emergency braking function8 km/hVehicle haltElectromechanical parking brakeESP (ECD)285_050 41Electromech. Parking BrakeAdaptive starting-off assistant This function permits smooth hill starting and stops the vehicle rolling back. The function is only activated if seat belt is fastened. The tilt angle is measured by a sensor in the control unit. In addition, the control action makes allowance for engine torque, accelerator pedal position and gear selected. The parameters listed above govern the point at which the parking brake is released when driving off. Automatic calibration of the tilt angle sensor and starting-off parameters takes place constantly. Whenever the vehicle is started on the flat, its acceleration behaviour is evaluated and adjusted for control purposes to the parameter set stored in the control unit. The function can be deactivated at the workshop but not by the driver.V282 Left parking brake motorV283 Right parking brake motorTilt angle Accelerat or pedal value Engine torque Engine speedTilt angle sensor (integrated into control unit)J540 Electromechanical parking brake control unitDrive system CAN J234 Airbag control unit (belt interrogation)Selector lever position J220 Motronic control unit J217 Automatic gearbox control unitAccelerator pedal value42F125 Multi-function switch285_051Brake pad wear recognition and play correction The pad thickness is automatically determined cyclically (approx. every 500 km) with the vehicle stationary and the parking brake not applied. For this purpose the brake pad is moved out of neutral position (= end position) towards the brake disc. The control unit uses the value measured by the Hall sender to calculate the brake pad travel and thus the pad thickness. Measurement is performed with the vehicle parked, the ignition lock applied and the parking brake released. If drivers regularly use the parking brake, the wear measurement may be less precise than if the parking brake is seldom applied.Special system functions Pad change mode Pad change is performed using the diagnosis tester VAS 5051 with the parking brake not applied. In basic setting function 5, the cylinder is fully retracted by the spindle drive (refer to Releasing parking brake on Page 38). The pad can be replaced after resetting the brake piston with the special tool VAS T10145. In basic setting function 6, the cylinder is moved back towards the piston (refer to Applying parking brake on Page 38). The pad thickness is entered in adaption function 6 (for detailed information, refer to current Workshop Manual).Roadworthiness test mode Metered braking on a dynamometer is necessary for checking parking brake operation. Roadworthiness test mode is recognised after 3 seconds if the rear wheels are turning at a constant speed of between 3 and 9 km/h on the dynamometer roller. Terminal 15 must be on for this purpose. The parking brake application action is modified by the control unit: Each time the switch is actuated, the piston is moved by a defined small amount and the brake applied slightly more.43Electromech. Parking BrakeEmergency release An applied parking brake can be released mechanically if electrical actuation is no longer possible or in the event of mechanical problems with parking brake components. An emergency key is provided for this purpose in the vehicle tool kit. The vehicle is to be jacked up and the appropriate wheel removed. The Torx head at one end of the key is used to remove the actuator from the brake caliper. The spindle can then be turned with the opposite end of the emergency key until the brake is released.285_085Fault displays Flashes constantly if parking brake has not been properly applied. Flashing on actuating parking brake pressure switch F234 indicates a wiring fault.285_086Fault detected by control unit restricting operation.285_087System fault; vehicle should no longer be driven for safety reasons.285_088 44Electromechanical parking brake CAN data exchangeJ540 Electromechanical parking brake control unit – Parking brake status (2) – Tensioning force attained (2) – Deceleration request (2) – Deceleration request release (2) – Terminal 15 status (2) – Parking brake fault message (2) – Fault lamp (6) – Acoustic warning (6) – Wear display (6) – EPB text messages (6) J255 Front climate control unit (7) – Ambient temperatureJ518 Entry and start authorisation control unit (5) – Status of steering wheel lock – Terminal 15 on – S-contactConvenience CAN Diagnosis CANJ533 Gateway (1) – Mileage (old) – Time (old) J285 Control unit with display in dash panel insert (6) – Displays – Acoustic signals (gongs) – Mileage – Date – Time – Standing timeJ104 ESP control unit (2) – Vehicle speed – Wheel speed – TCS/MSR request – ABS braking – ESP/EBPD intervention – Brake pressure – Front brake temperature/EPB – Deceleration available – EPB message plausible – Quattro driveDash panel insert CANJ220 Motronic control unit (3) – Engine speed – Closed throttle position information – Accelerator pedal value – Engine torque loss – Driver input torque – Clutch switch statusDrive system CANJ217 Automatic gearbox control unit (4) – Gearbox status – Target gear/gear engaged – Selector lever position – Torque converter lock-up clutch statusJ234 Airbag control unit – Driver's belt buckle interrogation285_089 45ESPSummaryThe Audi A8 `03 is fitted with the ESP 5.7 already used in the Audi A4. In addition to the necessary software adaptation to the new vehicle, the main new features are as follows:Communication interface ECD (electronically controlled deceleration) The interface enables other vehicle systems to actuate the ESP. The ESP control unit J104 can be informed directly of deceleration requests. The ECD request involves deceleration of the vehicle at a maximum rate of 8 m/s2. Brake pressure is built up evenly at all four wheels. The interface in the A8 is used by the electromechanical parking brake and adaptive cruise control functions.J428 Distance regulation control unitJ104 ESP control unitWheel brakeWheel brakeWheel brakeWheel brake285_05246Active speed sensors The new sensors detect the corresponding wheel speed directly at the wheel bearing by way of magnetic multipoles. Direction of rotation and size of air gap are also determined (refer to System components for design and operation).285_053New software modules The TCS function has been upgraded to include improved traction on non-compacted surfaces (e.g. deep snow). Greater wheel slip values are accepted for acceleration when travelling straight ahead or with small steering angle. Directional stability has priority when cornering. The permissible slip values are reduced. ESP control action is reduced if a sporty driving style is required. Directional stability is maintained but larger float angles are permitted, leading to higher wheel slip values in transverse vehicle direction. A sporty driving style is recognised from evaluation of accelerator pedal actuation.47ESPSystem componentsHydraulic modulator The basic version of the hydraulic modulator corresponds to that in the Audi A4. Compliance with noise level requirements with adaptive cruise control action necessitates the use of integrated suction dampers. These take the form of small chambers which dampen brake fluid pulsation by way of rubber diaphragms. This modified modulator is used exclusively in vehicles fitted with adaptive cruise control. Attainment of a high level of braking comfort requires the use of the linear solenoid inlet and switching valves developed for the ESP 5.7.285_090Solenoid switching valveSolenoid intake valve Return pumpSolenoid inlet valveSolenoid outlet valve285_055ECD request not active: Valves deenergised Driver can regulate brake pressure by way of open solenoid switching and inlet valves.Pressure build-up in response to ECD request: Solenoid switching and intake valves energised, return pump suction action via open solenoid intake valve and pump regulates brake pressure.48Mode of operation of linear solenoid valves Application of current to the coil of the solenoid valve causes a magnetic force FM to act on the sealing element. The sealing element is pressed onto the seat in the valve housing. The forces exerted by the spring (FF) and the hydraulic fluid (FH) act in opposition to the magnetic force. If FF+FH becomes greater than FM, the sealing element is lifted off the seat and the valve opens. The higher the valve actuation current, the greater the hydraulic fluid pressure must be to open the valve.Varying the current level makes it possible to set different opening pressures. In addition, the valve stroke (= valve opening cross-section) can be set in the range between valve closed and valve fully open. This mode of operation enables the brake pressure to be varied as required. Such action is a prerequisite for comfortable vehicle deceleration.FMCoilSealing element SpringSeatFF + FH285_05649ESPSpeed sensors G44-47 Design: The measuring element is a Hall sensor consisting of three Hall elements. The conventional sensor ring is replaced by a magnetised wheel bearing seal carrying 48 pairs of north/south poles (multipole).285_057Operation The sensor detects changes in magnetic flux density. The three Hall elements are in offset arrangement. The gap between the elements is selected such that element A senses a magnetic maximum when C detects a magnetic minimum.Element A Element BElement C285_05850A difference signal A-C is formed in the sensor.285_057Signal A Signal C Difference signal A-C285_07451ESPHall element B is located centrally between A and C. Element B detects a magnetic maximum if signals A and C and thus also the difference signal are at zero. The point at which signal B reaches its maximum value (positive or negative) is evaluated for detection of direction of rotation. If, for example, zero crossing of the difference signal A-C is reached by a trailing signal edge and the signal B maximum is then negative, anti-clockwise rotation is recognised.Trailing signal edgeNegative maximumDifference signal A-C Signal B285_075Electrical configuration The speed sensor is connected by way of a current interface to the ESP control unit, which is fitted with a low-impedance shunt R. The speed sensor has two electrical connections and forms a voltage divider together with the shunt. Battery voltage UB is applied between connections 1 and 2. The sensor signal produces a drop in voltage US at the shunt. This signal voltage is evaluated by the control unit.521 Sensor IS 3 UB R US2 285_061The output signal of the speed sensor is a PWM signal (PWM = pulse width modulation). The number of pulses in a specific time unit provides the – speed information.The following information is encoded by means of the pulse width: – Direction of rotation – Size of air gap – Installation position – Detection of stop The correct air gap size is important for system operation and is detected and evaluated for system self-diagnosis.North WidthSouthNorthSpeed information 285_062Diagnosis Within the scope of self-diagnosis the system is monitored for mechanical faults, electrical faults and implausible signals. The most important system data are stored in the measured value blocks and can be read out with the diagnosis tester VAS 5051. Detailed information can be found in the relevant Workshop Manual.53Tyre Pressure MonitoringSummaryThe Audi A8`03 is fitted with a new version of the tyre pressure monitoring system, the principal new features of which are described in the following. Aerials Use is made of active aerials. The radio signals transmitted by the tyre pressure sensors are converted by the aerials into digital signals. There are two aerial versions which differ in terms of the carrier frequency (433/315 MHz) to be processed.Data transfer The digital signals are transferred from the aerials to the tyre pressure monitoring control unit via the LIN bus. The major advantage of this method is the minimal susceptibility to electromagnetic interference.Tyre pressure monitoring control unit The control unit is located beneath the rear seat bench. There is no sensor signal conditioning in the control unit. Only one control unit frequency version is required as the signals are already conditioned in the aerials.SensorSensor Aerial/ receiver LIN busAerialHF cableControl unit/ receiverControl unit285_063285_0641st generation components and networking (Audi A8 up to `03)542nd generation components and networking (Audi A8 as of `03)Control concept System operation forms part of the MMI control concept. Pressing the CAR button and selecting "Systems"- "Tyre pressure monitoring system" provides a display of the current tyre pressures and temperatures or enables the following settings to be made: – System activation/deactivation – Storage of tyre pressures (Refer to operating manual for detailed information)285_065Warning displays Warnings continue to be displayed in the dash panel insert. The two-stage warning priority system has been retained (refer to operating manual for detailed information).55Tyre Pressure MonitoringTyre pressure monitoring system CAN data exchangeJ502 Tyre pressure monitor control unit – Allocation of identifiers to aerials (1) – Request for aerial messages (1) – System status (all) – Output of information (warnings, system faults, pressure, temperature) (2, 3) LIN R59...R62 Tyre pressure monitoring aerials (1) – Tyre pressure, temperature, battery status of sensors – Level of signals receivedJ518 Entry and start authorisation control unit – Terminal 15 status Convenience CANJ644 Energy management control unit – Load deactivation (LIN driver) J533 Gateway J285 Control unit with display in dash panel insert (2) Dash panel insert CAN – Status of warning and system fault displaysMOSTDrive system CAN J220 Motronic control unit – Engine speed J104 ESP control unit – Vehicle-speed signalJ523 Front information display and operating unit control unit (3) – User request285_067 56Service The range of service diagnosis options has been extended. Aerial diagnosis is performed constantly and does not have to be started separately. (For details, refer to current Workshop Manual and assisted fault-finding)57Run Flat System - PAXSummaryFor the first time in the luxury class, a "run flat" wheel system is available as an option for the Audi A8 `03. As compared to other systems, the PAX run flat system represents an optimum compromise between handling, comfort and durability requirements. Both a summer and a winter version are available.Design: The system consists of rim, support ring, tyre and tyre pressure sensor. All components have been newly developed. The rim is of a completely new geometrical design. The support ring is fitted onto the centre of the rim and is made of a heavy-duty plastic with honeycomb structure. The tyre is no longer tensioned behind the rim flange by means of its bead, but rather inserted in the rim seat. The geometrical and structural design of the PAX tyre differs considerably from conventional tyres, above all in the area of the side wall and bead. A glycerine gel is applied to the inner surface of the tyre to reduce the friction between support ring and tyre in run flat mode.Support ring Tyre Glycerine gelSupport ring Wheel285_06858Operation: In the event of partial or total loss of pressure, the tyre rests on the support ring. The special design of the bead seating on the rim stops a flat tyre coming off. This is particularly critical in situations involving cornering with the tyre side wall subject to tensile load. The tensile force Fz causes the tyre bead to rotate about the bead core, thus producing a force Fw in the outer bead area which presses the bead more firmly onto its seat.FzFw285_069PAX enables a fully laden vehicle to be driven for a maximum of 200 km at a speed of max. 80 km/h even with a completely flat tyre. Despite the use of the gel, component temperature and hence wear increase, in particular on account of the friction between tyre and support ring. A high degree of ride comfort is maintained even in run flat situations. A loss of pressure is thus not always immediately apparent. For this reason, PAX always includes the tyre pressure monitoring function. Run flat mode is indicated on the dash panel insert centre display.285_07059Run Flat System - PAXNew tyre designation PAX tyres have a new designation. Arithmetically, the wheel used for the A8 corresponds to a wheel size of 18.3".Tyre width [mm]Speed symbol Load indexTyre diameter [mm] Wheel diameter [mm]285_068Service Tyre removal/fitting involves completely new procedures. New tyre fitting machines and PAX attachments for conventional fitting machines are available.60All rights reserved. Subject to technical modification. Copyright* 2002 AUDI AG, Ingolstadt Department I/VK-35 D-85045 Ingolstadt Fax 0841/89-36367 000.2811.05.20 Technical status as at 07/02 Printed in Germany285