TECHNICAL DOCUMENTATION

SSP 293 Audi A8 ´03 – Infotainment

PDFEN72 pages1 MB
SSP 293 Audi A8 ´03 – Infotainment - PDF cover

This PDF is currently unavailable.

Read document text
293Service.AUDI A8 ´03 - InfotainmentSelf Study Programme 293For internal use only Definition of terms Data bus network (topology) The topology provides a general outline of the way in which control units fitted in the vehicle are interlinked by way of data bus systems. It thus becomes clear which bus systems are used by the control units to exchange data. Distributed functions Function masterThis Self Study Programme contains information on the infotainment system and the associated distributed functions in the Audi A8 ´03. With distributed functions, one control unit is always responsible for the entire sequence of operations. The function master control unit gathers all input information. The requests resulting from this are then transmitted in the form of a message on the data bus system and read into the control units concerned for corresponding actuation of the appropriate connected components. Substitute masterThis introduction contains explanatory notes to clarify the meanings of certain terms, designations and symbols used in this Self Study Programme.An understanding of the interaction of the components and distributed functions forms the necessary basis for successful faultfinding.More detailed information can be found in the following Self Study Programmes:– SSP 282 – Audi A8 ´03 Technical Features – SSP 286 – New Data Bus Systems – LIN, MOST, BluetoothTM – SSP 287 – Audi A8 ´03 Electrical Components – SSP 288 – Audi A8 ´03 Distributed Functions – SSP 289 – adaptive cruise control in the Audi A8 '03 This term indicates that several control units are required to exchange information in order to implement a function.WiringConvenience CANComponents and symbolsDrive system CAN Example: Opening up displayAdaptive cruise control CAN1In the event of function master failure affecting major functions, the task of the function master is assumed by a control unit provided for this purpose and designed to maintain the sequence of operations (possibly with certain restrictions).Dash panel insert CANMOST busA number is used to designate the information sequence described in the corresponding text. The green circle symbolises the start of an information sequence.E462LIN bus The green arrow indicates input information.Diagnosis CANBidirectional wireV301Reception wire The blue arrow indicates output information.E380 J523Transmission wireDiscrete wireWireless transmission – transmission signalJ520 SSP293_058 J533Wireless transmission – reception signalFollow-up functionThe layout of the individual components such as control units, switches or control elements as illustrated corresponds to the actual arrangement in the vehicle. Component designations are explained on the basis of their identifiers in the relevant text.Prerequisite Components marked in red indicate the function master within a sequence of operations.1 Pressing the open/close button for front display E462 transmits a signal to the multimedia operating unit E380. 2 The multimedia operating unit relays the signal to the front information display and operating unit control unit J523. 3 This signal is transmitted via the MOST bus to the data bus diagnostic interface J533.4 The data bus diagnostic interface transmits the signal via the convenience CAN to the onboard power supply control unit 2 J520. 5 The open/close display motor V301 receives the "Open display" signal via a discrete wire. The display is opened up.Components marked in yellow indicate the substitute master. ContentsPage Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 InfotainmentSystem layout of CAR functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Infotainment system layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Multimedia interface (MMI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Front information display and operating unit control unit J523. . . . . . . . . . . . . . 17 Front information and display and operating unit control unit J685 . . . . . . . . . . 20 Multimedia operating unit E380 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Multi-function steering wheel and display in dash panel insert. . . . . . . . . . . . . . 32Sound SystemIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Digital Bose® Surround sound system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Radio ModuleRadio module R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Dialog system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Telephone/Telematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63The Self Study Programme contains information on design features and functions. The Self Study Programme is not intended as a Workshop Manual. Values given are only intended to help explain the subject matter and relate to the software version applicable at the time of SSP compilation. Use should always be made of the latest technical publications when performing maintenance and repair work.NewAttention Note3 IntroductionSummary of media and functions in the Audi A8 ´03Both in the modern business world and in the private domain, mobile information and entertainment are becoming ever more important. In other words, vehicle occupants are becoming increasingly interested in enjoying the benefits of modern media. With this in mind, the Audi A8 ´03 is fitted with an infotainment system. The infotainment system offers a wide range of modern media (see Fig.).DVD - VideoDAB - Digital radioTelephone TelematicsCentral display and controlTV receptionCD/DVD navigationInternet Email Minidisc/CD audio SSP293_0014 Utilisation of the media can only be achieved by the installation of a distributed system. This means that a function, such as listening to a radio station, demands the interaction of several control units.An understanding of the way in which the control units are interlinked forms the basis for successful fault-finding.Example:Front information and display and operating unit control unit J685Front information display and operating unit control unit J523MOSTMultimedia operating unit E380Radio module RDigital sound package control unit J525Speakers SSP293_002 Rear window aerial module with aerial amplifier R245 InfotainmentSystem layoutCAR functions The multimedia interface (MMI) enables the driver to make settings for various vehicle systems. The illustration shows the control units interlinked for implementation of the CAR functions.Driver identification control unit J589Adaptive suspension control unit J197Front passenger seat adjustment with memory control unit J521Distance regulation control unit J428Wiper motor control unit J400 6 Sunroof electronics control unit J528Convenience system central control unit J393Parking aid control unit J446Tyre pressure monitor control unit J502Seat adjustment with memory control unit J136Entry and start authorisation control unit J518 Onboard power supply control unit J519 SSP293_003 7 InfotainmentSystem layoutInfotainmentFront roof module: - Microphone unit R164 - Telematics operating unit E264 Data bus diagnostic interface J533 Centre speaker Front information display and operating unit control unit J523Front information and display and operating unit control unit J685 Dash panel speaker Control unit with display in dash panel insert J285Operating unit in steering wheel E221Bass speaker in front doorTelephone/telematics control unit J526 Treble speaker in rear door Multimedia operating unit E380Bass speaker in rear doorTelephone handset R37 and telephone bracket R1268 CD single drive R92Aerial amplifier R24 Telephone aerial R65 CD changer R41 Navigation aerial R50Additional loudspeaker for telematics R91Subwoofer R148Surround speakers in rear shelfAdditional aerial for telematics R90Digital sound package control unit J525 Navigation system control unit J401 TV tuner R78 Radio module R and language input control unit J507 SSP293_004 9 InfotainmentMultimedia interface (MMI)The multimedia interface enables users of the infotainment system in the Audi A8 ´03 to implement a wide range of functions and settings with the aid of a central control element. The selection menues and settings can be viewed on an additional display in the dash panel. Users merely have to be familiar with four different control elements to be able to implement menu-driven activation of the required function. MMI control elements 1 Main function buttons Pressing the main function buttons calls up the main menu for the corresponding function group on the display. This permits rapid access to the desired function irrespective of the sub-menu currently being displayed. The SETUP button is an exception to this. The content of the menu which appears after pressing the SETUP button depends on the function group previously selected. The air conditioning system is operated by way of the Climatronic control unit J255. The setting and selection menues are however displayed in the MMI.Entertainment RADIO CD/TV/DVD Communication Internet Telephone SSP293_045Information Navigation INFO/telematics Control CAR SETUPThe internet (NET) + telematics functions will not be available until a later date.10 2Softkeys The functions of the softkeys differ depending on which menu is active. The softkey functions appear in the corresponding corners of the display.MemoryCD 1 Dire Straits - Brothers in …ForwardSourceTr. 12 10:56ManualTP TMC D2 PrivateSoundSSP293_0433Central control knob Turning the control knob effects selection of a menu item or setting. Pressing the control knob confirms the selection or setting.4RETURN button Pressing the RETURN button causes the higher-ranking menu to be displayed.11 InfotainmentList of functionsMemoryRadio FMHR 2 HR 3 SWR 3 RPR Eins Bayern 4 B 5 Akt Culture Pop Pop Pop Classical NewsTapeChangerCD 3Dire Straits - Brothers in … 6 - Ride across the river 7 - The man´s too strong 8 - One world 9 - Brothers in arms 03:55SourceManualTP TMC D2 PrivateSoundManualTP TMC D2 PrivateSoundRADIO central menu – Dynamic station list Memory – Memory list Tape – FM (VHF) – MW (medium wave) – LW (long wave) – DAB* (digital radio) Sound – See Setup - softkey sound Manual – Manual forward – Forward search – Store station – Play station – Search back – Manual back Radio setup – Traffic news – Regional setting – Station reception – Station display – Alternative frequency – PTY filter – Erase last stationsCD/TV central menu – CD track – TV station Changer – CD list Source – CD – TV – External AV source Sound – See Setup - softkey sound Manual – Forward – Back – Track back – Track forward – Track mix – Play track – Name CD CD/TV setup CD – Repeat – Display CD text TV – Brightness – Contrast – Colour – Picture format – TV standard* Not yet available12–Hardkey Softkey Sub-menu Function TP-MemoInfo5 3 3Kassel → FrankfurtSourcesMemoryNavigationCountryTown/ post codeRouteGermany Etting/Ingolstadt Ingolstädterstraße 10Between Alsfeld-West … Frankfurt → Cologne Between Bad Camberg Trunk road B 3 between Borken and …ServicesTP TMC D2 PrivateRoadSpecial destination Start navigationNav infoTP TMC D2 PrivateMapInfo central menu – TMC message list TP-Memo Message call Sources – Radio – Telephone* Services – Emergency call – Breakdown call Info setup – TP-Memo Timer – TMC display filterNavigation central menu – Single destination mode – – – – – Country Town/post code Road Special destination Start navigation– Route planning mode – Int. destinations 1…3 – Destination Memory – Last destinations – Top special destinations – Destination from address book – Store current destination – Store route* Not yet available– Load route Route – Route criteriaNavigation setup – Map colours – Alignment – Junction zoom – Map type – Map content – Voice messages – Demo mode– Route list – Route with intermediate destinations – Route without intermediate destinations – Block route as of here Map – Zoom – Map menu Nav info– Erase last destinations – Location, manual – Version information– Destination – Location – GPS data 13 InfotainmentUserCar adaptive air suspensionlift comfort automatic dynamicLogbookAddress bookRadio setupactive auto local variable possibleSettingsTraffic news Regional setting Station reception Station display Altern. frequency PTY filterSystemsTPMaintenanceDisplayTP TMC D2 PrivateSoundCAR central menu – Air suspension Users – Users 1 - 4 – User management Logbook – Brief instructions – Operating manual – Audi MMI Maintenance Systems – "Ambiente" lighting – Acoustic Parking System – Exterior lighting – Battery charge – Vehicle ID number – Windows – Dash panel insert – Tyre pressure monitoring system – Wipers – Seat setting – Mirror setting – Central locking CAR setup – Trailer mode – Jacking modeSETUP central menu – Radio setup Address book – Find entry – View list – New entry – Erase address book Settings – Menu language – Units – Time setting – System sound – Voice control – Factory settings Sound – Balance – Fader – Treble – Bass – Subwoofer DSP (Digital Signal Processing) – Standard – Bose® – Volume settings – – – – Navigation info Traffic bulletin Dialog system Telephone volumeDisplay – Brightness 14 MemoryTelephone6 7 8 9 0 + #SMSDistributionClimate control driverSeat ventilation4 3 2 15Number850434DEL A-Z*21,5° C6low high3Replace rec. TP TMC D2 PrivateDialBlowerSeat heatingTelephone central menu – Enter PIN – Telephone menu Memory – Address book – Numbers dialled – Calls accepted – Calls during absence – Number of SIM card – Store current number SMS – New SMS – Standard – SMS in – SMS out – SMS memory – Erase all SMS read – Erase all SMS Dial Replace receiver Telephone setup – Telephone settings – Call options – Security settings – Mailbox – Call re-routing – Network selectionClimate control central menu – Driver – Front passenger Distribution – Driver – Front passenger Seat ventilation – Driver – Front passenger Seat heating – Driver – Front passenger Blower – Driver – Front passenger Climate control setup – Econ – Automatic air recirculation – Synchronisation – Centre vent Rear control – Solar operation – Auxiliary heating – Auxiliary ventilation – Timer setting – Operating time15 InfotainmentDesignJ285J685MOST J527 J533J523E380 E221 SSP293_008The multimedia interface (MMI) consists of the following: – Front information display and operating unit control unit J523 – Front information and display and operating unit control unit J685 – Multimedia operating unit E380 – Operating unit in steering wheel E221 – Control unit with display in dash panel insert J285Data are transferred from the steering wheel operating unit via the steering column electronics control unit J527 and data bus diagnostic interface J533 to the corresponding control units.16 Front information display and operating unit control unit J523Control unit J523 is the infotainment system master control unit.Functions – Reception of user function requests with the aid of the multimedia operating unit E380 and dialog system (SDS, optional) – Control of communication on MOST bus (it thus represents the MOST bus system manager; for information on MOST bus, refer to SSP 286 – New Data Bus Systems – LIN, MOST, BluetoothTM) – Actuation of front information and display and operating unit control unit J685 for displaying information – Actuation of control unit with display in dash panel insert J285 for displaying MMI information – Diagnosis for multimedia operating unit E380 and front information and display and operating unit control unit J685SSP293_030Fitting location Front information display and operating unit control unit is fitted at module carrier behind glove box.SSP293_02317 InfotainmentInput and output signalsMultimedia operating unit E380RS232 RS232Front information display and operating unit control unit J523MOST busTV tuner R78FBAS FBASMedia player, position 1 R118Front information and display and operating unit control unit J685Convenience CAN Drive system CAN Adaptive cruise control CAN Dash panel insert CANLVDSData bus diagnostic interface J533SSP293_009The front information display and operating unit control unit J523 uses a great number of input signals and controls a wide range of functions. For the sake of clarity, the input and output signals of the front information display and operating unit control unit are explained in greater detail in the descriptions of the individual components and functions contained in this Self Study Programme. The illustration shows the layout of the components connected to the front information display and operating unit control unit.18 Diagnosis Address word 07 - Control and display unit The self-diagnosis monitors – Communication with other control units via MOST bus/data bus diagnostic interface/CAN bus – Power supply – Temperature of Fibre Optical Transmitter (FOT) (refer to SSP 286 - New Data Bus Systems) – Operation of MOST busCorresponding fault memory entries are made in the event of malfunction.Encoding The encoding sets the MMI language version.Measured value blocks The following measured values are displayed in the measured value blocks: – – – – – Power supply Status of terminals S, 15, X, 50 MOST address (position in ring) MOST identifier (type of unit) Status of diagnosis wireAdaption The following settings can be made in adaption mode: – List of control units fitted for implementation of CAR functions – RHD/LHD – Time span for automatic closing of info menu – Speed shutoff threshold for TV picture, CAR menu, adaption process for one touch memory – Reduction of optical power of FOT for test purposes19 InfotainmentFront information and display and operating unit control unit J685The display unit is concealed when switched off. It is opened up on activating the MMI system with the aid of an electrically actuated mechanical unit in the centre section of the dash panel. Mechanical unit Design Milled rupture joints are provided in the housing for crash safety.Open/close display motor V301Open display limit switch F330Close display limit switch F331SSP293_013 Open/close button for front display E462 Emergency release cableOperation The display unit is opened up after activating the MMI or by way of the open/close button for front display E462. When the ignition is switched on, the display unit is returned to the status prior to switching off the ignition.20 Operation The motor for opening up the display unit is actuated by the onboard power supply control unit 2 J520 with the aid of a regulated voltage. The voltage level influences the opening up and closing speed and can be set in adaption mode. The onboard power supply control unit 2 recognises full opening up/closing of the display unit by way of the display unit open/ closed limit switches. When the display has been opened up, two spring-loaded balls engage in the display unit mount. After reaching the end position, reduced voltage is still applied to the motor for a brief period to ensure firm positioning against the stop. This prevents rattling.Obstruction safeguard The obstruction safeguard takes the form of a dog clutch integrated into the motor.Emergency release Removing the chest vent provides access to the cable-operated emergency release. Pulling the cable disengages the dog clutch in the motor and the mechanism is free to move.uStart-upDisplay is openedReductionHolding of reduced voltagetSSP293_015Opening up and closing of display Address word 4E - Electronic central electrics 2 The holding time and voltage level can be set in adaption mode.The statuses of the limit switches are displayed in the measured value blocks.21 InfotainmentDisplay The display has dimensions of 154 x 87 mm and a resolution of 480 x 240 pixels. Thin-film transistor (TFT) technology as used for flat screens, notebooks and notepads provides high quality image representation. Display options:Input and setting menuesMemoryRadio FMHR 2 HR 3 SWR 3 RPR Eins Bayern 3 Bayern 4 Culture Pop Pop Pop Pop ClassicalTapeAddress bookRadio FMBalanceSettingsLeftRightManualTP TMCD2 PrivateSoundDisplayTP TMCD2 PrivateSoundNavigation system map displayMemoryPC interfaces (internet, email)Route MemoryNavigationInternetWWWAudi Online servicesIngolstadtStart Nav infoTurn for zoomMapE-MailTP TMCWapTV and video images in 16 : 9 format22SSP293_016 Input and output signals The front information and display and operating unit control unit J685 is directly linked by way of a 22-core wire to the front information display and operating unit control unit J523.Low Voltage Differential Signalling (LVDS) image dataDiagnosisDisplay temperatureDisplay luminosity J523 Status of tubular discharge lamp inverter J685Switched 12 V power supplySSP293_017The wire is not intended to be repaired. It must be replaced complete. Take care to ensure clearance from opening-up/closing mechanism when laying wire.23 InfotainmentLow Voltage Differential Signalling (LVDS) The LVDS signal is used in modern communication equipment such as computers for digital transmission of the image data from the processor unit to the display. To ensure electromagnetic compatibility (EMC), the signal requires twisted wire pairs similar to CAN bus technology. In other words, opposing voltage signals are transmitted on the two wires to prevent interference with other electronic systems. The voltage difference between the recessive and dominant bit is only 0.5 V, hence the designation Low Voltage Differential Signalling (LVDS) for this technology. In contrast to a CAN bus, LVDS is not used to transmit data packets. The bits are transmitted continuously. The transmission frequency is 210 MHz. Service checking of this signal is not possible with the measuring instruments currently available. The function of the LVDS signal is therefore monitored in the Audi A8 by the front information display and operating unit control unit J523 by way of comprehensive selfdiagnosis. Whenever the system is switched to standby mode (refer to SSP 286 – New Data Bus Systems), the front information display and operating unit control unit J523 transmits data to the front information and display and operating unit control unit J685 for checking the LVDS link. The incoming data are checked in the display unit for completeness and plausibility by way of a computer operation. If the display unit establishes that the LVDS signal is not OK, it uses a diagnosis wire to transmit a fault message back to the control unit.Display temperature The display is fitted with an NTC temperature sensor. The temperature sensor permits checking of the current display temperature. Proper operation is guaranteed over a broad temperature range. Exceeding the display operating temperature can damage the display unit. This can initially be seen from bright areas at the corners of the display but ultimately leads to total failure.24 Status of tubular discharge lamp inverter The display unit is fitted with two tubular discharge lamps to illuminate the viewing points. Voltages of up to 1300 V are applied to the tubular discharge lamps. This high voltage has to be generated by an inverter integrated into the display unit. In addition, the inverter recognises the failure of one or both tubular discharge lamps. The display unit relays this information by way of an additional wire to the control unit J523.Display luminosity In the Audi A8, the control unit with display in dash panel insert J285 sets the degree of switch and display dimming. The dimming level is transmitted as a percentage value to the corresponding control units by way of the data bus systems. In order to adjust the illumination of the display unit to the specified degree of dimming, the control unit J523 has to be provided with the current luminosity as feedback. This measured value is determined by a photodiode installed in the display and transmitted on an additional wire from the display to the control unit J523.25 InfotainmentDiagnosis Address word 07 - Control and display unit The current temperature and luminosity of the display unit are indicated in the measured value blocks.The display unit fault messages – LVDS signal failure – Failure of one or both tubular discharge lamps – Maximum permissible temperature exceeded are stored in the fault memory. Test pattern selectionRed screenChequer board patternGrey step pattern SSP293_018The adaption mode can be used to present various test patterns in the display unit. In addition, the brightness of the display unit can be adjusted using the adaption function.Assisted fault-finding Functional test Adaption Type b - Enter adaption valueAudi V05.02 18/06/2002 Audi A8 2003 2003 (3) Saloon BFM 4.2l Motronic / 246 kW+Adaption - Output test pattern on MMI displayCurrent value: Test pattern, 64 grey steps (vertical bars)–Abort2. Functional description+ – AbortNo test pattern Test pattern, chequer board (inverse) Program terminationMeasurementVehicle selfdiagnosisJumpPrintHelpSSP293_034 26 Multimedia operating unit E380Driver identification control unit J589 SSP293_022 Interior aerial 1 for entry and start authorisation R138The following components are integrated into the operating unit: – Buttons and control knob for MMI operation – Electronics for converting button and controller signals into digital data – Aerial for remote control of MMI (optional) – Parking brake contact switch F321 – Entry and start authorization button E408 – Driver identification control unit J589 (optional) – Interior aerial 1 for entry and start authorisation R138The multimedia operating unit E380 converts the button and control knob signals into digital information with the aid of the integrated electronics. This information is transmitted by means of a serial interface (RS232) to the front information display and operating unit control unit J523. In addition, the control unit J523 transmits information back to the operating unit.The parking brake contact switch F321, the interior aerial 1 for entry and start authorisation R138 and the driver identification control unit J589 are independent components. Further information on these components can be found in SSP 287 – Audi A8 ´03 Electrical Components.27 InfotainmentInputs/outputsFront information display and operating unit control unit J523RS232 RS232Open/close button for front display E462Multimedia operating unit E380Onboard power supply control unit 2 J520SSP293_020Serial interface (RS232) signals: Operating unit – – – – – Front information control unitButtons Control knob selection Control knob ON/OFF, volume MMI remote control aerial Open/close button for front display E462Front information control unitOperating unit– Button and controller illumination – Message confirming reception of button and controller signals28 Serial interface (RS232) "Serial interface" is a computer engineering term and means that digital information is transmitted consecutively (serially). The designation RS232 denotes the data transmission standard. The information is only transmitted in one direction per wire. Two wires are therefore required for exchange of data between two control units. The plug connection at the control unit for data reception is abbreviated RX (receive). The plug connection for data transmission is designated TX (transmit). On actuating a button or controller, the serial interface is monitored by the control unit J523 self-diagnosis. An entry is made in the fault memory if the exchange of data is not OK.29 InfotainmentOpen/close button for front display E462 The button is integrated into the operating unit in front of centre console E461. The wake-up process for the MOST and convenience CAN bus systems takes roughly 3 - 4 seconds. This results in delayed opening up of the front display unit if the bus systems are in sleep mode. The operating unit therefore transmits the signal to the onboard power supply control unit 2 J520 on two paths.1. Bus systems activeOpen/close display motor V301 Front information and display and operating unit control unit J685Open/close button for front display E462 Front information display and operating unit control unit J523Serial interface RS232 Multimedia operating unit E380 MOSTOnboard power supply control unit 2 J520Convenience CANData bus diagnostic interface J533SSP293_04730 2. Bus system sleep modeOpen/close display motor V301Open/close button for front display E462Multimedia operating unit E380Onboard power supply control unit 2 J520 SSP293_021Closing of the display by pressing the open/ close button for front display E462 requires data transmission by way of the bus systems. Wake-up wire The wake-up wire is bidirectional. If a button is pressed with the bus systems in sleep mode, the operating unit transmits a once-only wake-up pulse to the front information display and operating unit control unit J523 to start the system. If the infotainment system is activated by a different wake-up procedure, the control unit transmits a wake-up pulse to the operating unit to activate its electronics.Diagnosis Address word 07 - Control and display unitFault memory entries Fault memory entries are made in the event of – Problems with data transmission between operating unit and control unit – Sticking of or short circuit in one or more operating unit buttons – Sticking of or short circuit in "Open/close display unit" button in the fault memory of the control unit J523. Measured value blocks The statuses of the buttons and control knob in the operating unit as well as the "Open/ close display unit" button can be shown in the measured value blocks. Adaption The brightness of the button illumination can be adjusted using the adaption function.31 InfotainmentMulti-function steering wheel and display in dash panel insertThe Audi A8 ´03 is fitted with a multi-function steering wheel as standard. It offers the driver tiptronic® operation as well as voice control and volume regulation. In addition it makes the functions of the dash panel insert display available to the driver. Consequently, there is no need for the driver to take a hand off the steering wheel to make use of functions such as telephone, navigation, audio source selection or driver information system DIS and all the necessary information is provided in the driver's field of vision. This represents a major contribution to increased road safety and convenience.Voice control start/termination buttonDash panel insert display Menu selection controlSSP293_010Volume/navigation message repetition control MODE buttonMODE button The driver selects the appropriate menu by pressing the MODE button several times. Menu selection control The driver selects the required menu item by turning the control. Selection is confirmed by pressing the control.Volume/navigation message repetition control The driver sets the volume by turning the volume control. After pressing the control, the last navigation system voice message is repeated. Display in dash panel insert Depending on steering wheel button operation, the driver is presented with the selection menues for radio station, CD track and telephone address book. Navigation information is also presented on the display.32 Multi-function steering wheel signal transmission The operating unit in the steering wheel is a LIN slave control unit.Menu startMenu selection Start/terminate voice control Button illumination Volume E221tiptronic® +tiptronic® -LINSteering angle sender G85 with coil connectorSSP293_011 Convenience CANJ527The operating unit in steering wheel E221 detects the steering wheel button and control signals and converts these into digital information. The digital information is transmitted with the aid of a LIN bus wire in the coil connector of the steering angle sender G85 to the steering column electronics control unit J527.The steering column electronics transmits the information from the LIN bus to the convenience CAN. The multi-function steering wheel information is distributed by the data bus diagnostic interface J533 to the other bus systems in accordance with the functions concerned. The control units implement the corresponding functions.33 InfotainmentExample: Switching radio station by way of multi-function steering wheelControlE221J523 MODE button J527Radio module RJ533 J285 MOSTSpeakers J525SSP293_0121 The driver presses the MODE button several times to call up the desired selection menu in the dash panel insert display J285. 2 Each button signal is converted by the operating unit in steering wheel E221 into digital information. The operating unit transmits this information by way of the LIN bus wire to the steering column electronics control unit J527.3 The steering column electronics control unit J527 integrates the "MODE button pressed" information into a convenience CAN message. 4 The data bus diagnostic interface J533 reads the information on the convenience CAN and transmits it on the MOST bus to the front information display and operating unit control unit J523.34 5 Following reception of each "MODE button pressed" signal, J523 transmits the graphics data for presentation of the next selection menu in the display of the control unit with display in dash panel insert J285 to the MOST bus. 6 The data bus diagnostic interface J533 transmits this information to the dash panel insert CAN. 7 The dash panel insert reads this information and presents the corresponding selection menu in the display. Procedures 1 to 7 are repeated each time the MODE button is pressed until the radio station selection menu appears on the dash panel insert display. 8 The driver selects the desired radio station by turning the left control. Each turn updates the dash panel insert display. Selection is confirmed by pressing the control. Signal transmission from the operating unit in steering wheel E221 to the front information display and operating unit control unit J523 and from the control unit J523 to the dash panel insert is implemented in the manner described above. 9 The front information display and operating unit control unit J523 starts playing of the selected radio station. For further information, refer to Page 52.35 InfotainmentSelf-diagnosis Address word 16 - Steering column electronics When the convenience CAN is active, the steering column electronics control unit J527 checks – communication on LIN bus wire to operating unit in steering wheel E221 – tiptronic® and MMI buttons as well as controls and illumination for short circuit and open circuit A corresponding fault memory entry is made in the event of malfunction.Encoding The steering wheel equipment must be stated in the steering column electronics control unit encoding.Measured value blocks The measured value blocks display – Signal inputs of buttons and controls – Hardware and software version of operating unit in steering wheel E221 – Status of communication on LIN bus – Measured value of heated steering wheel sensor G428Control element test The steering wheel heating and button illumination are switched on by way of the control element test for checking.36 Sound SystemIntroductionEven the standard version of the new digital sound system in the Audi A8 ´03 achieves a quality of sound dynamics and acoustics previously unattained in series systems. The optional Bose® Surround sound system offers an even better overall effect, volume adjustment to compensate for vehicle noise (AudioPilotTM) and unique surround sound. Digital sound system The digital sound system makes use of 5 audio channels. The stereo signals are distributed over 5 channels by the digital system and reproduced by 9 speakers. This dispersion of audio signals gives listeners the impression of being in the middle of a concert hall. Standard sound systemDash panel: Tweeter 36 mm Front door: Bass/mid-range speaker 168 mm In roof module: Two microphone inputs Rear door: Tweeter 36 mm Bass/mid-range speaker 168 mm Tweeter 36 mm Bass/mid-range speaker 168 mm Tweeter 36 mmBass/mid-range speaker 168 mmRear shelf: Subwoofer 225 mm 5-channel DSP amplifier 4 x 40 W + 1 x 70 W (subwoofer) Vehicle Noise CompensationMOST connection Ring fault diagnosis wire Power supplySSP293_036 37 Sound SystemNew sound settings In addition to the familiar sound settings, the user can make certain new adjustments to the sound system with the help of the MMI.MemoryRadio FM Balance Fader Treble Bass Subwoofer DSPTapeManualTP TMCD2 PrivateSoundSSP293_042ChangerTV DSP BOSE Sound setting Surround level Music/speech AudioPilotTM Normal Driver RearSourceManualTP TMCD2 PrivateSoundSSP293_060Sound setting – Normal: The sound system sets the speakers to optimum reproduction for all seats. The sound system is set specially for the driver. The sound reproduction is optimised for the rear seats.Music/speech Clarity of speech reproduction requires different sound settings to those for music reproduction. As an additional service, RDS radio stations transmit the corresponding encoded information together with the signal for spoken broadcasts (news, traffic bulletins). If the music/speech changeover function is active, the sound system reproduces the spoken broadcasts with a special speech tuning stored in the software.– Driver:– Rear:38 New feature: Speed-dependent volume adaption (GALA) The digital sound system in the Audi A8 ´03 is fitted with an advanced version of the familiar speed-dependent volume adaption function (GALA). The new GALA function is integrated into the digital sound package control unit J525. It uses the vehicle speed to calculate the typical background noise level. On the basis of the background noise level established, the control unit only increases the volume of the frequency bands affected.As the typical background noise level differs depending on whether a vehicle is fitted with a petrol or diesel engine, the engine version must be set in the encoding.39 Sound SystemDigital Bose® Surround sound system (optional)Dash panel: Left main channel 70 mm Centre (mid-range/treble/ bass speaker) 70 mm Front door: Woofer 200 mm In roof module: Two microphone inputs Rear door: Tweeter 36 mm Tweeter 36 mm Woofer 200 mm Right main channel 70 mmBass/mid-range speaker 168 mmBass/mid-range speaker 168 mmRear shelf: Subwoofer 300 mm 2 x Surround (mid-range/treble/ bass speaker) 8 mm8-channel DSP amplifier 6 x 25 W + 2 x 50 W (front woofer) + 1 x line-out output for active subwoofer, AudioPilot TMMOST connection Ring fault diagnosis wire Power supplySSP293_03740 The digital Bose® Surround sound system in the Audi A8 ´03 makes use of 8 audio channels. Front main channel speakers R26, R27 The left and right main channel speakers in the dash panel transmit – the mid-range and high frequencies – the music and all video mode sounds intended to be emitted from the front but not directly from the centre Centre channel speaker R158 The function of the centre channel speaker R158 is visual and audio harmonisation in video mode. In other words, it permits the assignment of sound to images, thus creating the impression that the actors' voices are coming from the centre of the screen. For music reproduction, the digital Bose® Surround sound system uses the centre speaker to achieve the all-round effect. Listeners have the impression of being in the centre of a concert hall regardless of whether they are on the right or left side. Bass channel in front doors R21 and R23 The passive woofers in the front doors reproduce the low audio frequencies in the front area of the passenger compartment and thus amplify the full bass effect in the vehicle. Two main channels at rear The rear-door mid-range/bass speakers R15, R17 and the tweeters R14, R16 act in the same way as the front main channels to reproduce music and sound for the rear area of the passenger compartment. Surround channel The two mono surround speakers R150 achieve the all-round acoustic effects. They are installed beneath the rear shelf on the right and left. As both speakers reproduce exactly the same sound, they are connected in series. Rear subwoofer The active rear subwoofer reproduces the bass tones and thus reinforces the full bass impression during music reproduction. The subwoofer is actuated via a line-out output. The external subwoofer amplifier boosts this incoming signal to 100 W.The surround sound function is only available for purely stereo sources such as CD and DVD. The surround sound function is not activated in radio and TV mode, as the input signals are sometimes only mono. The acoustic coordination of all speakers is essential to the reproduction of surround sound. If one of the speakers does not reproduce the correct tones due to malfunction, the surround sound effect will be considerably impaired.41 Sound SystemAudioPilotTM The AudioPilotTM function provides compensation for vehicle background noise by increasing the volume of the frequency band affected.Noise level Too loudMusic with AudioPilotTM Music without AudioPilotTMBackground noise SSP293_039 TimeThe background noise is picked up by the microphones in the roof module and evaluated by the digital sound package control unit J525. The problem with background noise detection is to distinguish this from music or speech. Example: The noise of the AC fresh-air blower cannot be distinguished by the AudioPilotTM from the sound patterns of music. The digital sound package control unit J525 thus requires the following additional information: – Speed of AC fresh-air blower – Engine versionThe speed of the fresh-air blower enables the digital sound package control unit J525 to recognise the sound picked up by the microphones as background noise and provide compensation for this. The engine version enables the digital sound package control unit to recognise the engine background noise picked up by the microphones and to increase the volume of the frequency bands affected. As with series equipment, the engine version – diesel/petrol engine – must be set in the encoding.42 Bose® Surround sound system settings In addition to the sound settings described above, the Bose® Surround sound system features sound level adjustment. With this function, users can select the area of the passenger compartment for which surround sound reproduction is to be adjusted.MemoryTV DSP BOSESound setting Surround level Music/speech AudioPilotTM On On TP TMC NormalSourceManualSoundSSP293_04143 Sound SystemAudio management distributed function The front information display and operating unit control unit J523 is the audio master in the infotainment system of the Audi A8 ´03. This means that the volume and sound settings made by the user are stored separately for the individual modes in control unit J523. The sound settings are made by the user either with the corresponding mode activated or with the aid of the "Sound/volume settings" setup menu in the MMI. These settings are stored on a personalised basis (optional) when the infotainment system is switched off. The key-specific settings are activated by way of the remote control key recognition function in the entry and start authorisation control unit J518. In vehicles with one touch memory (fingerprint, optional), the personalised settings are activated by way of the driver's fingerprint. Further information can be found in SSP 287 – Audi A8 ´03 – Electrical Components.The illustration shows the different modes and the transmission paths for the information required for volume control.Radio bulletins, navigation system voice messagesJ446 E380 J527 MOST J523 PTT buttonJ533J526 J104J525 Speakers J528 44 SSP293_040 The audio signals are transmitted directly by way of the MOST bus from each audio source to the digital sound package control unit J525. 1 Entertainment: The volume and sound settings for the entertainment functions can be made by the user on the multimedia operating unit E380 and are stored separately and on a personalised basis (optional) for each mode. 2 Information: In the event of emergency and traffic messages, the entertainment functions and voice control system are interrupted. Traffic messages are output on the driver's side, emergency announcements on all speakers. 5 Control: Activation of the dialog system (SDS) by way of the PTT button in the steering wheel reduces the volume of the entertainment functions. Active traffic or emergency messages are terminated. Output is on the driver's side. 6 Communication: When telephoning via the telephone/ telematics control unit, the volume of the entertainment functions is reduced. The driver has the option of setting the telephone output as required between front and rear.During navigation messages, the volume of the entertainment functions is reduced. 7 Microphone module: Navigation messages are output on the The microphones are used for the driver's side. AudioPilotTM function (optional). 3 Acoustic Parking System (APS): The microphone signals are transmitted When the APS system is active (parking aid in the form of digital information to the control unit J446), the volume of the MOST bus. entertainment systems is reduced. The number of microphones depends on 4 Vehicle speed: vehicle equipment. The "vehicle speed" information is transmitted by the ABS with EDL control unit J104 with the aid of the drive system CAN via the data bus diagnostic interface J533 and the MOST bus to the front information display and operating unit control unit J523. This information is required for the GALA function. Further information on the microphones can be found in the following.45 Sound SystemMicrophonesDriver's side Front passenger's sideMicrophone 3Microphone 2Direction of travelMicrophone 1 SSP293_035An Audi A8 ´03 with the full range of equipment has three microphones accommodated in a unit in the front roof module. The number of microphones depends on vehicle equipment and must be observed on component replacement.Depending on equipment version, the analog microphone signals are converted into digital signals in the digital sound package control unit J525 or telephone/telematics control unit J526 and transmitted by way of the MOST bus. The table lists the available options.SDS NoTelephone/ telematics NoMicrophone connected to DSP: No microphone fitted Bose® DSP: Microphone 2 connected to DSPMicrophone audio data MOST bus NoneNoYesDSP: Microphone 1 connected to telephone/telematics Bose® DSP: Microphone 1 connected to telephone/telematics; Microphone 2 connected to DSPWith Bose® DSPTELYes YesNo YesMicrophones 1 and 2 connected to DSP Microphones 2 and 3 connected to DSP Microphone 1 connected to telephone/telematics Microphone signals following processing by echo suppression in SDS control unitDSP DSP TELSDS SDS SDSSDSTEL46 Diagnosis Address word 47 - Digital sound packageFault memory entries The following result in corresponding fault memory entries – Supply voltage undershot/exceeded – Open circuit/increased attenuation in MOST bus – Short circuits or open circuits in speakers – Short circuits or open circuits in microphones (optional) – Loss of communication with control units by way of bus systems – Activation of component protection in the digital sound package control unit J525.Measured value blocks The measured value blocks display – – – – – – – – – – Power supply MOST address MOST identifier (type of unit) Status of ring fault diagnosis wire Status of AF mute connection Vehicle speed Speed of cooling blower (only Bose®) Amplifier temperature Manufacturer's data (serial number, etc.) Voltages at microphone inputs (optional)47 Radio ModuleRadio module RThe radio module contained in the basic equipment of the Audi A8 ´03 permits integration of additional systems into the infotainment system. Plug-in positions are additionally provided for three modules, one of which is used for the language input control unit J507 plug-in module. The function of the radio module is to ensure analog radio station reception, to convert aerial signals into digital audio signals and to transmit these by way of the MOST bus to the digital sound system. As with the second generation symphony radio, the radio module has two integrated radio tuners. Information on this topic can be found in SSP 254 – Audi A4 ´01 Technical Features.Radio module RUnused plug-in positions Language input ontrol unit J507 SSP293_025Fitting location The radio module is installed on a base plate on the left of the luggage compartment.SSP293_02648 Input/output signalsHF signalMOSTAerial amplifier R25 IF signalRadio module RRing fault diagnosis via bidirectional wireSSP293_027Radio stations are received by way of four FM aerials integrated into the rear window and one AM aerial. The mode of operation of the aerial amplifier R25 with integrated aerial diversity corresponds to that of the aerial module in the Audi A4 ´01. All the control signals and the audio signals converted into digital information are transmitted by way of the MOST bus.49 Radio Module"Radio listening" distributed functions The front information display and operating unit control unit J523 is the master control unit for this function. The reception data of up to 20 radio stations are stored in the control unit and listed in the RADIO main menu in the front information display unit. Radio stations which have been stored but are not currently being received appear in grey. 6 radio stations which have been listened to for at least 45 seconds are displayed at the top of the list and stored on a user-specific basis. New radio stations received replace those which have not been listened to for the longest. The display sequence is based on the Programme Identifier (PI) code. This enables radio stations belonging to one group to be displayed in direct succession. Information on the PI code can be found in SSP 147 – Radio Systems ´94. The station category (PTY code) is also shown in the list. Users can select the desired station categories in the radio function setup menu. Like the PI code, the PTY code is integrated into the RDS data and contains additional information on the set radio station.Station group Hessischer RundfunkMemoryRadio FMTapeHR 2 HR 3 SWR 3 RPR Eins Bayern 3 Bayern 4Culture Pop Pop Pop Pop ClassicalManualTP TMC D2 PrivateSoundSSP293_038 Station category using PTY code50 51 Radio ModuleThe front information control unit retains the last user-specific status (display open/closed; radio/CD/TV etc.) prior to switch-off. When switched on again, the stored status is reactivated. The illustration shows the sequence of operations when switching on the infotainment system in radio mode in a vehicle with one touch memory system (optional).J589 J685J523J533 MOSTJ525 Radio module RSpeakersAerial amplifier R25Aerials FM1 - FM4 52SSP293_024 1 The user provides identification by way of the entry and start authorisation button E408. 2 The last user-specific status before switching off the system is stored in the front information display and operating unit control unit J523. 3 The "driver identification" information is transmitted by the driver identification control unit J589 to the convenience CAN. By way of the data bus diagnostic interface J533, this information is also available to all other control units involved in memory control. In the example shown, "RADIO" had been the last active mode for this user and the display unit had been open. Opening of the display unit is as described in the "Open/close display unit button" Section. 4 The front information display and operating unit control unit J523 transmits an enquiry to the radio module R: – Which radio stations are currently being received? – Which transmission channels are being used for audio transmission? 5 The radio module responds with the required information and starts to transmit the synchronous data for audio transmission to the MOST bus.6 The front information control unit transmits the graphics data to the front information display unit. The corresponding station list is presented in the display unit. In addition, the front information control unit transmits the following information – Command for reproduction of radio transmission channels – Volume (user-specific) – Sound setting (user-specific) – Muting OFF to the digital sound package control unit J525. 7 The digital sound package control unit converts the digital audio transmission data into analog signals and reproduces these via the speakers. The user hears the radio station.53 Radio ModuleDiagnosis Address word 56 - RadioEncoding The encoding is used to set – The country version for adaption of frequency bands – The infotainment system configuration to ensure communication by way of the data bus systemsControl element test In the control element test, a test tone with a frequency of 100 Hz is transmitted by the radio module R to the digital sound package control unit J525. The digital sound system reproduces the test tone via the speakers. This permits checking of the audio data transmission by way of the MOST bus.Fault memory entries The following situations – Power supply undershot/exceeded – MOST bus open circuit/increased attenuation – Loss of communication with navigation system control unit J401 – Open circuit/short circuit in HF wire – Open circuit/short circuit in IF connection result in corresponding fault memory entries in the radio module.Measured value blocks The measured value blocks display – – – – – Power supply MOST address (position in ring) MOST identifier (type of unit) Status of diagnosis wire Power supply and current input of aerial amplifier and aerial diversity – Strength of current radio station reception54 Dialog system (SDS)The language input control unit J507 is fitted in the radio module in the form of a plug-in module. It is a self-contained control unit with separate MOST address and address word for self-diagnosis. The functions of the familiar voice control system have been considerably extended in the Audi A8 ´03 SDS. The table provides a summary of the SDS functions. The "Help" command informs the driver of the commands available on the current level. This represents a major contribution to increased road safety and ride comfort.RADIO VHFCD Next CDNavigation Start/stop navigation Destination entry Go to address book entry Map settingsAddress book Specify nameTelephone Enter PINNext stationPrevious CDRead out nameCall nameStation number 1 … 99 87.5 … 108.0 (direct frequency input) Play station station name Station name (specify)CD number NFind entry and make call NavigatePrivateNext trackOfficePrevious trackTraffic news ON/OFF Traffic news (read out)EraseFixed networkTrack number 1 … 99Call name (private/office/ fixed/mobile) Navigate to nameMobileStation list (read out + select)Specify CD nameNumber 0123456789CD name (play) CD list (read out + select)CorrectDialRedial55 Radio ModuleVoice control input/output signalsPTT button in steering wheelJ528E221J523 J526 MOSTJ527J533 J525J507 in radio module RSpeakersSSP293_029E221 J507 J523 J525 J526 J527 J528 J533Operating unit in steering wheel Language input control unit Front information display and operating unit control unit Digital sound package control unit Telephone/telematics control unit Steering column electronics control unit Sunroof electronics control unit Data bus diagnostic interfaceThe plug-in contacts in the radio module are used for all input and output signals, as well as the power supply. MOST bus data transmission in the radio module is by way of electrical pulses. This is made possible by – Screening against electromagnetic interference by way of the metal case – Short transmission path56 The illustration on the left shows the input and output signal paths. 1 The SDS is activated by pressing the PTT button in the operating unit in steering wheel E221. 1a As shown, the button signal is transmitted to the language input control unit J507. 2 The digital sound package J525 and telephone/telematics J526 control units convert the signals from the microphone unit in the roof module into digital information and transmit this by way of the MOST bus to the language input control unit. 3 The dialog system speech output is achieved in the reverse direction using the digital sound package control unit. 4 The user requests are transmitted by the dialog system by way of the MOST bus to the front information display and operating unit control unit J523. 5 As infotainment master, the control unit J523 actuates the appropriate control units to implement the required functions.The digital microphone signals are filtered by means of an elaborate software function in the language input control unit and mixed to improve recognition of voice commands. Microphone signal processing is also active in telephone hands-free mode. The language input control unit J507 provides the telephone/telematics control unit J526 with the processed microphone signals by way of the MOST bus. This considerably enhances hands-free quality.Component protection The language input control unit J507 is incorporated into the component protection system. In other words, activated component protection results in restricted dialog system operation.57 Radio ModuleDiagnosis Address word 67 - Voice controlFault memory entries The following situations – Power supply undershot/exceeded – MOST bus open circuit/attenuation – Loss of communication with entry and start authorisation control unit J518 – Activated component protection result in corresponding fault memory entries in the radio module.Measured value blocks The measured value blocks display – – – – – – Power supply MOST address (position in ring) MOST identifier (type of unit) Status of diagnosis wire PC board temperature Reception level of microphones during last command – Last command recognised, for example "RADIO"Control element test The language input control unit performs an internal self-test in "control element test" mode. Any faults occurring are displayed.58 NavigationIntroductionMemoryNavigation destinationCountry Germany Town/ Etting/Ingolstadt post code Road Ingolstädterstraße 10 Special destination Start navigationRouteMemoryNavigationLast destinations Top special destinations Destination from address book Info items Store current destination LogbookRouteNav infoTP TMCD2 PrivateMapNav infoTP TMCD2 PrivateMapMemoryNavigationRouteMemoryLMNavigation destinationK NOPQR SRouteTown/post codeT U ETTI V W X Ettikon Y Z Ettikoner HofIngolstadtJ I H G F E D C B0-9A0..9Etting EttingenLISTDELNav infoTurn for zoomMapNav infoMapSSP293_048The navigation system in the Audi A8 ´03 permits the use of Digital Versatile Discs (DVD) as navigation system information source. A DVD is capable of storing up to 4.7 gigabytes of data. This corresponds to roughly seven times the storage capacity of a CD-ROM. Navigation data for several countries and additional information such as travel guide, restaurant guide and sports guide can thus be stored. The destination input menu has been extended to include the box "Country".Users can still also select destinations by entering the post code. Destination entries using the dialog system are an optional feature. With this function, the name of the place or road can be given as voice command. Address book The "Memory" function enables users to make entries in an address book. The following data – Surname – First name – Category and the navigation data relating to the entry are stored.59 NavigationInput/output signals Navigation system control unit J401G47 G45J285R50 J685 J104 J401 J523 J533J525MOSTE380Driver's side speakers J526 Radio module R J507 R24 R65 SSP293_049Signals for calculating current vehicle location 1 Satellite navigation Design and operation of the GPS navigation aerial R50 correspond to those of the GPS aerial installed in the Audi A4 ´01. The aerial is located at the top of the rear window. Dead reckoning Front wheel travel pulses2 The navigation system in the Audi A8 ´03 uses the number of front wheel travel pulses for dead reckoning. The number of front wheel travel pulses is calculated by the ABS with EDL control unit J104 on the basis of the front left G47 and front right G45 speed sensor signals and transmitted to the drive system CAN. The data bus diagnostic interface J533 reads the information in the drive system CAN and transmits it by way of the MOST bus to the navigation system control unit J401.60 Yaw rate 3 As with familiar navigation systems, a yaw rate sensor is integrated into the navigation system control unit J401. 7 The navigation system control unit J401 transmits the audio data in a synchronous MOST bus transmission channel. As instructed by the front information display and operating unit control unit J523, the digital sound package control unit J525 reduces the volume of the entertainment functions and reproduces the audio data by way of the speakers on the driver's side. The telephone/telematics control unit J526 and the radio module R transmit the traffic news data by way of the MOST bus to the navigation system control unit J401. This makes allowance for the reported traffic hold-ups in the dynamic navigation process. On the navigation map display, traffic hold-ups take the form of graphic symbols. A new feature is that the traffic hold-up symbols relating to the opposite direction and thus not affecting the navigation process are shown in grey. In addition, users can have traffic information displayed in text form by way of the multimedia interface after pressing the INFO button.Front information display and operating unit control unit J523 4 As infotainment system master, the control unit J523 controls - Destination input and selection with the aid of the MMI and dialog system - Presentation of navigation displays in the front information display unit and dash panel insert display - Reproduction of voice messages via speakers8Language input control unit J507 5 The language input control unit J507 transmits the voice inputs for destination entry and navigation activation converted into digital information to the front information display and operating unit control unit J523 by way of the MOST bus. J523 accepts the entries and controls the navigation system accordingly.6 By way of the MOST bus, the navigation system control unit J401 transmits the information - For presentation of navigation displays to the front information display and operating unit control unit J523. This makes use of the information to set up the presentations which are then shown on the two displays. The map display images are an exception to this. These images are set up by the navigation system control unit. - For reproduction of voice messages to the digital sound package control unit J525.61 NavigationDiagnosis Address word 37 - Navigation Measured value blocks As with the previously described systems, the MOST communication statuses are displayed in the measured value blocks. New measured value blocks as compared to familiar navigation systems are – – – – – – Temperature of CD/DVD drive Direction of travel Status of satellite reception Status of CD/DVD drive Status of EJECT button Current longitude and latitude based on GPS signal – GPS dataFault memory entries The following situations – Incorrect loading and ejection of CD/DVD-ROM – Exceeding of max. perm. temperature of CD/DVD drive – Access problems with navigation CD/DVD data – Implausible yaw rate sensor signal – Sticking of EJECT button – MOST bus open circuit or increased attenuation result in fault memory entries in the navigation system control unit J401.Adaption In addition to adaption of the familiar navigation systems, the adaption function permits – Self-testing of processor unit – Self-testing of CD/DVD drive – Ejection of CD/DVD62 Telephone/TelematicsIntroductionMemoryTelephone5 6 7 8NumberSMS4 3 2 19 0 + #85044DEL A-Z*Replace rec. TP TMCD2 PrivateDialSSP293_051In addition to the multimedia interface, the Audi A8 ´03 has been fitted with a completely new communications platform for telephone and telematics applications. The communications platform features dualband capability. In other words, the telephone and data link can be established by way of the carrier frequencies 900 (D-network) and 1800 (E-network) MHz. The MMI and hands-free unit are used for control and operation of the communications platform. A cordless handset is also available as an option.BluetoothTM technology is employed for the exchange of data between handset and communications platform. Inform