TECHNICAL DOCUMENTATION

SSP 300 09D 6 Speed Auto Transmission

PDFEN56 pages5 MB
SSP 300 09D 6 Speed Auto Transmission - PDF cover

This PDF is currently unavailable.

Read document text
Service.Self-Study Programme 3006-speed automatic transmission 09DDesign and function Compared to the 5-speed automatic transmission, the 09D 6-speed automatic transmission provides: – a reduction in fuel consumption, – a reduction in exhaust emissions, – improved acceleration values and – a reduction in noise.300_U2This self-study programme provides you with the design and function of the new 6-speed automatic transmission which is installed in the Touareg.NEWCaution NoteThe Self-Study Programme describes the design and function of new developments! The contents are not updated.Please always refer to the relevant service literature for up-to-date inspection, adjustment and repair instructions.2 At a glanceIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Selector lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Design of gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Check your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Operational diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Self-diagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553 IntroductionThe 09D 6-speed automatic transmissionwas developed at the famous Japanese manufacturer of automatic transmissions, AISIN Co., LTD, where it is manufactured. In the development of the control unit software, the years of experience that Volkswagen engineers have had with fuzzy logic-controlled driving programmes that depend on driving situations and hindrances has been a determining factor. This 6-speed automatic transmission, which has a very compact construction, is being used for the first time in the Volkswagen Touareg.Gearbox ventilation300_002Spare parts number AISIN model number Manufacturer Production date Gearbox codes300_081Serial number of the manufacturer4 Special gearbox features include: • fuzzy logic-controlled switching programmes that depend on driver and driving situations as well as switching programmes that depend on driving impedance • a controlled converter bypass coupling • lifetime ATF filling • The hill-holder function secures the vehicle from rolling back and permits hills to be approached comfortably. • selector lever and steering wheel Tiptronic switchesGearbox ventilationElectrical connections300_001.1ATF cooler connectionsMultifunction switchTechnical dataVolkswagen designation Gearbox codes ATF ATF filling amount Maximum torque transmission Weight Emergency run depending on engine including ATF in case of defective control unit with V10-TDI-engine with V6 engine with V10-TDI-engine with V6 engine AG6 - 09D EXG EXL Lifetime filling 12 litres 9.6 litres 750 Nm 97 to 110 kg 3rd gear and R gear5 Selector leverThe selector lever positionsP - Park Before the selector lever can be moved out of the Park position, the ignition must be switched on. In addition, the foot brake and the locking button on the selector lever must be pressed. R - Reverse The locking button on the selector lever must be pressed to switch into reverse. N - Neutral The gearbox is idling in this position. No power is being transmitted to the wheels. If the selector lever is in this position for a long time, the foot brake must be pressed again to activate the lever. D - Drive In the Drive position, the forwards gears are switched automatically.300_003Locking buttonS - Sport The control unit selects gears automatically according to a ”sporty” switching characteristic curve. The individual gears are extended further.Selector lever position and gear display in dash panel insert After the ignition is switched on, the current selector lever position is displayed in the dash panel insert. In positions ”D” and ”S”, the gear selected in the gearbox is also displayed.P R N D3 S123,4 km 12,3°C 123456 km300_0046 The Tiptronicin the Touareg is available as a selector lever as well as a steering wheel switch. Selector lever Tiptronic”+” Move up a gear ”-” Move down a gearThe Tiptronic channel is reached by moving the selector lever to the right out of the ”D” position. The control unit for the automatic gearbox thus enters the Tiptronic mode. The driver can now actively select gears.Tiptronic channel Steering wheel switches300_006Steering wheel - Tiptronic switches The steering wheel switches offer an optimal ergonomic actuation for gear selection. Here you use: – the switch on the right to move up a gear. and – the switch on the left to move down a gear. If the selector lever is in the ”D” or ”S” position when the steering wheel switches are pressed, the automatic transmission control moves into Tiptronic mode. Control automatically reverts to the previously selected ”D” or ”S” programme if the steering wheel switches are not pressed again.300_036Gear display in the dash panel insert6 5 4 3 2 1123,4 km 12,3°C 123456 kmThe current gear is displayed in Tiptronic mode.300_0057 Selector leverSelector lever lock and ignition key removal lockMagnet for selector lever lock N110 This is located in the front on the selector lever frame. It prevents the actuation of the selector lever from the positions ”P” and ”N” when the brake is not being applied.N110How it works Once the ignition has been turned on, the magnet for the selector lever lock is put under current by the control unit for automatic transmission, thus blocking the selector lever. If the control unit receives the signal ”brake applied” via the CAN data bus, it cuts off current to the magnet and the selector lever can be moved.300_021Selector lever frameEffects of a signal drop-out If one of these two signals fails or if the magnet is faulty, the selector lever can be moved out of ”P” and ”N” without applying the brake – assuming the ignition is turned on.30 31 E415 E408 N376 J217 J518 Kl.15 N110 F319 N380E408 - button for starting/stopping the engine E415 - switch for access and start authorisation F319 - switch for selector lever locked in P J217 - control unit for automatic gearbox J518 - switch for access and start authorisation N110 - magnet for selector lever lock N376 - magnet for ignition key removal lock N380 - magnet for selector lever lock P300_0418 The magnet for selector lever lock ”P ” N380 is at the selector lever frame, as is the magnet for the selector lever lock. It prevents the selector lever from moving out of the ”P” position when the ignition is switched off. The ignition must be switched on to activate the lock button.Switch F319How it works The magnet N380 is without power when the ignition is switched off, thus disabling the selector lever in the ”P” position. After the ignition is switched on, the magnet N380 receives power from terminal 15 and the lock is lifted. The switch F319 signals to the access and start authorisation control device that the selector lever is in the ”P” position.Magnet N380300_02130 E415 E408 N376Effects of a signal drop-out If one of the signals fails or the magnet for selector lever lock ”P” is defective, then the selector lever cannot be moved out of the ”P” position. The disablement has to be manually unlocked for towing the vehicle. For this purpose the centre console covering is to be removed and the magnet actuated by hand. The selector lever has to be simultaneously moved out of the ”P” position.J217 J518Kl.15N110 F319 N380300_042”Press”300_0219 Selector leverThe magnet for ignition key removal lock N376 is located within the switch for access and start authorisation E415 and prevents the ignition key from being removed when the selector lever is in a driving position. The ignition key removal lock works electromechanically.Inside tract300_080How it works The magnet for the ignition key removal lock N376 contains two spring-loaded locking pins which engage into the inside tract of the inserted ignition key if the selector lever is not in the ”P” position (N376 without power). The ignition key cannot be withdrawn.300_038N376 without power300_039Locking pins locked in placeN376 with powerWhen the selector lever is in the 'P' position, a signal travels from the switch for the selector lever in ”P” F319 to the access and start authorisation control unit J518. The control unit then sends current to the magnet for the ignition key removal lock N376. The locking pins are pulled out by the magnets and thus removed from the extended inside tract of the ignition key.Locking pins removed300_040The ignition key can be withdrawn.10 Electric circuitry If the ignition is switched off and the selector lever is in the ”P” position, a signal travels from the switch F319 to the access and start authorisation control unit J518. The control unit then sends current to the magnet for the ignition key removal lock N376. The locking pins are removed. The ignition key can be withdrawn. If the selector lever is not in the ”P” position when the engine of a vehicle with start/stop buttons is switched off, the dash panel insert emits an optical and acoustical warning. The driver is thus informed that the selector lever is not in the ”P” position.30 31 E415 E408N376J217 J518Kl.15 J285 N110 F319 N380300_043Effects of signal drop-out The electromechanical lock cannot be released if either the signal from the selector lever to the control unit J518 or the signal from the control unit to the switch for access and start authorisation E415 fails. The key cannot be withdrawn. In these circumstances, the ignition lock has an ... emergency release for the ignition key. Press the emergency release button with a pen or similar object to activate the emergency release for the ignition key. While keeping the button pressed, turn the ignition key to the left and remove it.”Press”300_037Emergency release button11 Design of gearboxFitting position of partsTorque converter Coupling K3 Simple planetary gear setConverter bypass couplingDrive sideStarter ring gearGearbox input shaftATF pump driveATF pumpGearbox input speed sender G182Brake B112 Coupling K1Dual planetary gear setCoupling K2Drive shaftParking lock wheel300_022Free-wheelBrake B2Oil panGearbox output speed sender G195Parking lock13 Design of gearboxIntroductory description of functionsThe gearbox housing consists of an aluminium alloy. The six forwards gears and the reverse gear are switched using a Lepelletier arrangement of the planetary gear sets. To switch the gears, – three multi-disc couplings, – two multiple disc brakes and – a free-wheel are switched on or off using the electromechanic-hydraulic control unit in the control valve assembly. The control unit for the automatic gearbox starts the switching of the gears and monitors the process for problems. After the signals of the information senders (sensors), the actuators are activated. Activation takes place depending on driver, driving situation and driving impedance switching programmes. The gearbox is adapted to use with different engines (V10 or V6) in the Touareg using – the number of installed disc pairs for the brakes and the couplings, – the size of the torque converter and – the geometric adaptation of the torque converter housing. The transmissions of the individual gears remain the same for both engines. A transfer gearbox flanged onto the gearbox distributes the torque to the axle drives.Torque converter with converter bypass coupling and ATF pumpThe hydromechanical torque converter serves as a starting element and increases the torque in the transforming area. It is equipped with a converter bypass coupling. Starting at an engine speed of 1000 rpm, the control unit for the automatic gearbox can close this coupling. This transfers the engine torque directly to the drive input shaft.300_022aATF pump Torque converter Converter bypass coupling Starter ring gear14 Starter ring gearATF pump driveThe figure shows the torque converter of the V10-TDI.300_063Torque converter Converter bypass couplingConverter bypass coupling Function The control unit for the automatic gearbox controls the solenoid valve N91. The solenoid valve opens or closes the converter bypass coupling depending on the engine's speed and torque.”Closed” Solenoid valve N91If the converter bypass coupling is to be closed, the solenoid valve opens the oil reservoir upstream of the converter bypass coupling. As a result, the oil pressure in this reservoir decreases; the oil pressure downstream of the converter bypass coupling closes the converter bypass coupling.300_034”Open” Solenoid valve N91When the solenoid valve N91 closes the oil flow again, the pressure upstream of the converter bypass coupling builds up again and the converter bypass coupling opens.300_03315 Design of gearboxThe ATF pumpis a gear pump and is driven by the ATF pump drive (pump gear shaft) of the torque converter. It suctions the ATF from the oil pan of the gearbox through the oil sieve. The ATF pump generates the working pressure for: – the multi-disc couplings and multiple disc brakes, – the lubrication circulation system and – the coolant circulation system. The ATF is cooled in a cooler. This cooler is located in front of the engine cooler (as seen in the driving direction).300_064ATF coolerEngine coolerDrive300_035300_062Pressure sideSuction sideEngineATF pump in automatic transmission16 The Lepelletier arrangementis based on a simple planetary gear set and a subsequent dual planetary gear set according to Ravigneaux. Lepelletier's brilliant idea was to drive the sun wheels and the planetary carriers of the dual planetary gear set at different speeds. Due to these different input speeds in the dual planetary gear set, the potential transmission doubles compared to a five-gear automatic gearbox to ten gears minus one gear. The sun wheels of the dual planetary gear set are driven with the transmitted output speed of the simple planetary gear set. The planetary carriers of the dual planetary gear set are driven with the gearbox input speed. As a result, the sun wheels and the planetary carriers have different speeds. In this automatic gearbox, six forwards and one reverse gear bring Lepelletier's brilliant idea to life.Simple planetary gear set Gearbox input shaftDual planetary gear set Drive shaft300_022kOutput speed, simple planetary gear setSun wheelPlanetary carrier17 Design of gearboxThe simple planetary gear setconsists of: – a sun wheel, – an internal gear and – 5 planetary wheels with V10-TDI engine and 3 planetary wheels with V6 engine, which are – guided by the planetary carriers. The input torque is guided through the simple planetary gear set on two paths: – from the gearbox input shaft without transmission via the coupling K2 on the planetary carrier of the dual planetary gear set and – through the simple planetary gear set with transmission to couplings K1 and K3.Planetary gearPlanetary carrierSun wheel Internal gear300_072K3 Gearbox input shaftK1K2300_022kSimple planetary gear set18 The dual planetary gear set,also known as the Ravigneaux planetary gear set, consists of: – an internal gear – a planetary carrier – two sun wheels with different diameters and – short and long planetary wheels. The multi-disc coupling K1 provides the connection between the internal gear of the simple planetary gear set and the large sun wheel of the dual planetary gear set. The multi-disc coupling K3 provides the connection between the planetary carrier of the simple planetary gear set and the small sun wheel of the dual planetary gear set. The multi-disc coupling K2 provides the connection between the transmission input shaft and the planetary carriers of the dual planetary gear set.Long planetary gear Planetary carrierLarge sun wheel Small sun wheel Short planetary gearInternal gear300_073Planetary carrier300_022kSmall sun wheelDual planetary gear setLarge sun wheel19 Design of gearboxThe multi-disc couplingsdrive the two sun wheels and the planetary carriers of the dual planetary gear set when they are closed. Depending on the gear to be switched, they are placed under ATF pressure by the control unit for the automatic gearbox via a solenoid valve in the control valve assembly; this closes them. Each multi-disc coupling is supplied with ATF pressure by another solenoid valve. The number of installed disc pairs per coupling varies with the maximum torque that can be transmitted. The multi-disc coupling K1 is closed in gears 1 to 4 and is controlled by the solenoid valve N90. It is compensated for centrifugal pressure. In the V10-TDI, for example, seven multi-disc pairs are installed.300_065300_022eThe multi-disc coupling K2 is closed in gears 4 to 6. It is controlled by the solenoid valve N282. It is compensated for centrifugal pressure. In the V10-TDI, for example, seven multi-disc pairs are installed.300_022d300_06620 The multi-disc coupling K3 is controlled by the solenoid valve N92 and is closed in gears 3, 5 and R. It is compensated for centrifugal pressure. In the V10-TDI, for example, five multi-disc pairs are installed.300_022cMulti-disc pairs300_067Information regarding the design and function of couplings that are compensated for centrifugal pressure can be found in SSP 172.21 Design of gearboxThe multiple disc brakessecure parts of the planetary gear sets when they are closed. To do this, they are submitted to ATF pressure by the control unit for the automatic gearbox via a solenoid valve or via the manual slider. The multiple disc brakes are supported on the gearbox housing by their exterior discs.300_022bThe multiple disc brake B1 brakes the small sun wheel of the dual planetary gear set. It is closed in gears 2 to 6 and is controlled by the solenoid valve N283. In the V10-TDI, for example, six multi-disc pairs are installed.300_069Exterior discsThe multiple disc brake B2 brakes the planetary carriers of the dual planetary gear set. It is controlled without a solenoid valve using the selector lever via the manual slider. It is closed in Reverse and, in the Tiptronic mode, in 1st gear. In the V10-TDI, for example, seven multi-disc pairs are installed.300_022fInterior discs300_06922 The free-wheelconnects the planetary carriers of the dual planetary gear set with the gearbox housing. If the exterior ring turns clockwise when the interior ring is braked, the bodies stand up and form a torsion-free connection between the interior and exterior rings. Free-wheeling is ”locked”. If the turning direction switches to anticlockwise, this connection breaks down. Free-wheeling works in ”D”- 1st gear and ”S” – 1st gear, ”tension” in the locking direction. In Tiptronic mode, 1st gear ”thrust” secures freewheeling of the multiple disc brake B2. This permits ”engine braking”.300_022h”free””locked”Interior ringExterior ring300_068 300_08223 Design of gearboxThe parking lockmechanically secures the vehicle from rolling away. The parking lock is activated purely mechanically using the selector lever cable when the vehicle is at a standstill. It engages in the parking lock wheel on the driveshaft and prevents turning of the driveshaft and thus of the vehicle wheels. The clamp pushes the parking lock in the gear teeth of the parking lock wheel and secures it.300_022gSelector lever cable connectionConnecting rods for parking lockParking lockConnecting rods for parking lock Clamp300_061300_018Selector shaftParking lock wheel24 Hillholder functionThe hill-holder function secures the vehicle from rolling back and permits hills to be approached comfortably. How it works If the control unit for the automatic gearbox detects an incline due to the driving impedance while simultaneously detecting a driving speed of ”zero”, it switches into 2nd gear. In 2nd gear, the vehicle cannot roll back because the internal gear of the dual planetary gear set would have to turn in reverse against the locking free-wheel. Free-wheeling is released and the vehicle starts comfortably only after the starting torque is greater than the slope descending force.Assignment tableThe following table shows in which gear the individual multi-disc couplings and multiple disc brakes are closed.Component Gear 1st gear 2nd gear 3rd gear 4th gear 5th gear 6th gear R gear K1 X X X X X X X X X X X X X K2 K3 B1 B2 F X** ”Engine braking”The braking force of the ”pushed” engine in particular driving situations – such as steep downhills – can be taken advantage of by applying the 1st gear in Tiptronic mode. The multiple disc brake B2 is closed in 1st gear only in Tiptronic mode.25 Design of gearboxEmergency runAfter certain components fail, normal operation of the automatic gearbox is no longer possible. In this case, the automatic gearbox can be operated only in emergency run. In emergency run, the converter bypass coupling is no longer closed and the gearbox is in 3rd gear in all forwards driving stages. When the selector lever is switched to the ”R” position, the manual slider is shifted, thus applying the Reverse gear. The emergency run mode is indicated by a different display in the dash panel insert. The ”Effects of signal drop-out” section in the Sensors and Actuators chapter describes which components must fail to lead to emergency run.300_075Manual slider26 Torque transmission in the TouaregThe torque of the engine is transferred to the automatic gearbox using the torque converter. As there is no axle drive within the automatic gearbox, a transfer gearbox is flanged onto the automatic gearbox. The engine torque is transferred from the driveshaft of the gearbox to the transfer gearbox. In the transfer gearbox, the torque is distributed between the front and rear axles, depending on the load. The transfer gearbox can be locked. This fixes the torque distribution between the front and rear axles. Each axle receives 50 % of the torque. In addition, there is a switchable reduction in the transfer gearbox. If this is switched on, the drive speed of the wheels is reduced by a factor of 2.7, thus increasing the drive torque. In the transfer gearbox, the torque is transferred further between the front and rear axles using cardan shafts. The differential of the rear axle to the transfer gearbox can also be locked using an electromechanical multi-disc coupling.EngineFront axle driveTransfer gearbox Automatic gearboxRear axle drive300_00827 System overviewSensorsGearbox input speed sender G182Gearbox output speed sender G195Multifunctional switch F125Gearbox oil temperature sender G93Sender 1 G193 and sender 2 G194 for hydraulic pressureSwitch for Tiptronic F189Switch for Tiptronic in steering wheel E438 and E439 Diagnostic connector28 CAN data busActuatorsControl unitsSolenoid valves in control valve assembly N88, N89Engine control unitSolenoid valves in control valve assembly N90, N91, N92, N93, N282, N283Control unit for transfer gearboxMagnet for selector lever lock N110ABS control unitControl unit with display unit in dash panel insert3 2 1 045 6 7 870 60 50 40 30 20 km/h 080 90 100 110 120 130 140 150 160 170 180 23 : 54 23 : 5423 : 54300_03129 SensorsThe gearbox input speed sender G182 is located within the gearbox. It is inserted in the housing of the ATF pump and uses a ring gear on the turbine shaft to determine the gearbox input speed. It works according to the Hall principle. Within the sender, there is an IC switch which activates the Hall sender.300_009Signal utilisation The control unit for the automatic gearbox uses the signal to detect the difference between the engine speed and the gearbox input speed. Using this speed difference, the slip of the converter bypass coupling is controlled up to a speed of 2000 rpm using the solenoid valve N91.Effects of signal drop-out The converter bypass coupling is closed without slip. The engine speed is used as the replacement speed.300_013kSender G18230 Turbine shaftSender G182Ring gear on turbine shaft300_011Electric circuitryG182G182 - gearbox input speed sender J217 - control unit for automatic gearbox+J217300_04431 SensorsThe gearbox output speed sender G195 is located above the control valve assembly and is screwed onto the gearbox housing. It determines the working speed of the automatic gearbox. It scans the outer teeth of the internal gear on the rear planetary gear set. It works according to the Hall principle. Within the sender, there is an IC switch which activates the Hall sender.300_010Signal utilisation The control unit uses the gearbox output speed to start switching the gears according to the switching plan.Effects of signal drop-out The speed signal of the ABS control unit is used as the replacement speed.32 Sender G195300_012Electric circuitry G195 - gearbox output speed sender J217 - control unit for automatic gearbox+ G195J217300_04533 SensorsThe multifunction switch F125 is screwed onto the exterior of the gearbox. Its duty is to further transfer the selector lever settings in automatic operation to the control unit for the automatic gearbox. The multifunction switch is connected with the selector shaft and the selector lever cable. If the multifunction switch is replaced, a position to the selector shaft must be set. If the switch is incorrectly set, the engine cannot be started.300_020Signal utilisation The control unit for the automatic gearbox starts the switch programmes according to the setting of the multifunction switch.Effects of signal drop-out As long as the difference between forwards and reverse gears can be determined, there are no effects on the switch programmes. If the Reverse gear signal is defective, the gearbox enters the emergency run.34 Lever for manual sliderConnection for selector lever cable (lever/selector shaft)Multifunction switchSelector shaft300_029Electric circuitry F41 F125 J217 J518 reverse gear switch multifunction switch control unit for automatic gearbox control unit for access and start authorisationJ518 F41 J21715aF12531300_04635 SensorsThe gearbox oil temperature sender G93 is located in the control valve assembly within the ATF. It checks the ATF temperature and reports this to the control unit for the automatic gearbox. It is an NTC resistor (NTC - negative temperature coefficient), i.e. the electrical resistance of the sender drops with increasing temperature.300_016Signal utilisationExample of an NTC resistor characteristic curvethe Starting at an ATF temperature of 150 torque converter bypass coupling is closed more frequently. If this does not result in cooling of the ATF, reduction of the engine torque is initiated starting at 170 oC. Effects of signal drop-out Harder gear shifts may occur.Ω ResistanceoC,105104103102101 -4004080120160Temperature oC300_07436 Geber G93300_013aElectric circuitryJ217G93 - gearbox oil temperature sender J217 - control unit for automatic gearboxG93300_04737 SensorsThe sender 1 G193 and sender 2 G194 for hydraulic pressure have the same design and are located in the control valve assembly. They monitor the ATF pressure behind the safety slides in the control valve assembly. This prevents couplings that do not correspond to the switch programme from closing. As a result, blocking of the gearbox is hindered. They function as diaphragm pressure senders. If the ATF pressure reaches a critical value, the pressure membranes are bent, closing the electrical circuit.300_015Electrical connectionSignal utilisation The signal is used to monitor the clutch control unit. If the ATF pressure is incorrect, the clutches are not activated.Pressure membraneEffects of signal drop-out Incorrect pressure signals can have effects in the control unit of the shifting unit.300_019Oil pressure38 Sender G194300_013bSender G193Electric circuitry G193 - sender 1 for hydraulic pressure, automatic gearbox G194 - sender 2 for hydraulic pressure, automatic gearbox J217 - control unit for automatic gearboxG193 G194ppJ217300_04839 SensorsThe switch for Tiptronic F189 is located under the selector lever covering on the plate. A ferromagnetic ”contact maker” is attached to each blind of the selector lever. The combination of the contact maker on blind 2 and the three Hall sensors on the plate form the switch for Tiptronic F189. When the blinds are moved, the contact makers change their position under the plate. In this way, a different Hall sensor is always activated – ”switched” – and sends a signal to the control unit for the automatic gearbox.Selector lever coveringHall sensor”Contact maker”Signal utilisation In the Tiptronic channel, tipping ”to the front” results in moving up a gear and tipping ”to the back” results in moving down a gear by the control unit for the automatic gearbox.Blind 2 Blind 1 Plate300_027aEffect of signal drop-out When the signal drops out, the Tiptronic function using the selector lever can no longer be used.Electric circuitry F189 - switch for Tiptronic J217 - control unit for automatic gearbox J519 - control unit for on-board network (The link to the selector lever lighting is required.)F189J519J217300_04940 The switches for Tiptronic in the steering wheel F438 and F439 are located to the left and right behind the steering wheel.The gears are switched by tipping the switches towards the steering wheel. The right switch (E438) is used to move up a gear ”+” and the left switch (E439) is used to move down a gear ”-”.Signal utilisation In Tiptronic mode, these switches can also be used to change gears. The switching signal is sent to the control unit for the automatic gearbox. If the Tiptronic switches on the steering wheel are pressed in the automatic mode, the gearbox control unit enters the Tiptronic mode. If the Tiptronic switches on the steering wheel are no longer pressed, the gearbox control unit automatically enters the Automatic mode.E439 E438300_028E438E439Effect of signal drop-out If the signal drops out, the Tiptronic functions using the steering wheel switch can no longer be used.J527300_050Electric circuitry E438 - switch for Tiptronic in the steering wheel E439 - switch for Tiptronic in the steering wheel J527 - control unit for steering wheel electronics41 ActuatorsSolenoid valvesSolenoid valves are used as electrohydraulic switching elements in the electronically controlled automatic gearbox. There are switching solenoid valves (yes/no valves) and control solenoid valves (modulation valves).The solenoid valve N88Solenoid valve N8works as a yes/no solenoid valve, opening or closing an ATF channel. If the solenoid valve is open, the gears 4 to 6 can be activated. The solenoid valve also improves the switching transition from 5th to 6th gear. If it is not under power, the solenoid valve is closed.300_013cEffect of signal or actuator drop-out The gears 4 to 6 can no longer be activated.J217Electric circuitry J217 - control unit for automatic gearbox N88 - solenoid valveN88N89N90N91300_05142 The solenoid valve N89Solenoid valve N89is located in the control valve assembly. It works as a yes/no solenoid valve, opening or closing an ATF channel. When the solenoid valve is opened, the ATF pressure on the converter bypass coupling is increased. If the solenoid valves N88 and N89 are opened simultaneously, the brake B2 closes so that the ”engine brake” is effective in Tiptronic mode, 1st gear.300_013dIf it is not under power, the valve is closed.Effect of signal drop-out If the signal to the solenoid valve N89 drops out, the converter bypass coupling can no longer be subjected to the maximum ATF pressure. Driving with the ”engine brake” is impossible.J217Electric circuitry J217 - control unit for automatic gearbox N89 - solenoid valveN88N89N90N91300_05243 ActuatorsThe solenoid valve N90 is located in the control valve assembly. It is a modulation valve that controls the ATF pressure to the multi-disc coupling K1. If it is not under power, the solenoid valve is closed. In this switching state, the maximum ATF pressure works on the coupling.Solenoid valve N90Effect of signal drop-out If the solenoid valve is defective or if it cannot be activated, switching of gears 1 to 4 may be harder.300_013eElectric circuitry J217 - control unit for automatic gearbox N90 - solenoid valveJ217N88N89N90N91N92300_05544 The solenoid valve N91 is located in the control valve assembly. It is a modulation valve that controls the ATF pressure on the converter bypass coupling. If the solenoid valve N91 is not under power, the converter bypass coupling is open.300_013fSolenoid valve N91Effect of signal drop-out The converter bypass coupling is not closed.J217Electric circuitry J217 - control unit for automatic gearbox N91 - solenoid valveN90N91N92N93300_05745 ActuatorsThe solenoid valve N92 is integrated in the control valve assembly. It is a modulation valve that controls the ATF pressure to the multi-disc coupling K3. If it is not under power, the solenoid valve is closed. In this switching state, the maximum ATF pressure works on the coupling.Solenoid valve N92300_013gEffect of signal drop-out If the solenoid valve is defective or if there is a fault in the circuit, switching of gears 3, 5 and R may be harder.J217Electric circuitry J217 - control unit for automatic gearbox N92 - solenoid valveN90 N91 N92 N93300_05346 The solenoid valve N93 is located in the control valve assembly. It is a modulation valve that controls the main ATF pressure in the gearbox, depending on the engine torque. If it is not under power, the solenoid valve is closed, so that the gearbox works with the maximum ATF pressure.Solenoid valve N93300_013hEffect of signal drop-out If the solenoid valve is defective or if there is a fault in the circuit, switching of all gears may be harder.J217Electric circuitry J217 - control unit for automatic gearbox N93 - solenoid valveN92 N93 N282 N283300_05847 ActuatorsThe solenoid valve N282 is located in the control valve assembly. It is a modulation valve that controls the ATF pressure to the multi-disc coupling K2. If it is not under power, the solenoid valve is closed. In this switching state, the coupling is closed with the maximum pressure.Solenoid valve N282300_013iEffect of signal drop-out If the solenoid valve is defective or if there is a fault in the circuit, switching of gears 4 to 6 may be harder.J217Electric circuitry J217 - control unit for automatic gearbox N282 - solenoid valveN92 N93 N282 N283300_05448 The solenoid valve N283Solenoid valve N283is located in the control valve assembly. It is a modulation valve that controls the ATF pressure to the multiple-disc brake B1.The solenoid valve closes depending on the current strength. If it is not under power, the brake is closed with the maximum ATF pressure.300_013jEffect of signal drop-out If the solenoid valve is defective or if there is a fault in the circuit, switching of gears 2 and 6 may be harder.J217Electric circuitry J217 - control unit for automatic gearbox N283 - solenoid valveN92 N93 N282 N283300_05649 ActuatorsThe magnet for selector lever lock N110 is located in the selector lever frame. It is an electromagnet that prevents the selector lever from moving out of the ”P” position when the ignition is switched on. If the selector lever is to be moved from this position, the foot brake must be pressed. If the ignition is switched on, the control unit for the automatic gearbox supplies the magnet with power. The magnet blocks the selector lever. If the foot brake is pressed, the control unit switches off the power to the magnet so that the selector lever can be pressed.300_021aMagnet for selector lever lock N110Effect of signal drop-out If the solenoid valve is defective or if there is a fault in the circuit, the selector lever can be pressed without having to press the foot brake.J217Electric circuitry J217 - control unit for automatic gearbox N110 - magnet for selector lever lockN110300_05950 Check your knowledgeWhich answers are correct? One, several or all answers can be correct.1.Name two types of solenoid valves that are used for the gearbox control unit. ...............................................................................................................................................................................2.On which part(s) of the automatic gearbox are brakes B1 and B2 supported? ...............................................................................................................................................................................3.Name the components of a simple planetary gear set. ...............................................................................................................................................................................4.What is the replacement interval for the ATF filling of the automatic gearbox? a) b) c) 20,000 km 2 years none (lifetime filling)...............................................................................................................................................................................5.On which principle is the Lepelletier arrangement based? a) b) c) two series-connected simple planetary gear sets one simple and one subsequent dual planetary gear set two series-connected dual planetary gear sets1. Yes/no valves and modulation valves; 2. On the gearbox housing; 3. Internal gear, planetary wheels, sun wheel and planetary carrier; 4. c; 5. b Solutions 51 Operational diagramComponent E438 E439 F125 F189 F319 - switch for Tiptronic in the steering wheel - switch for Tiptronic in the steering wheel - multifunction switch - switch for Tiptronic - switch for selector lever in P15G93 - gearbox oil temperature sender G182 - gearbox input speed sender G193 - sender 1 for hydraulic pressure, automatic gearbox G194 - sender 2 for hydraulic pressure, automatic gearbox G195 - gearbox output speed sender J217 J527 N88 N89 N90 N91 N92 N93 N110 N282 N283 N380 - control unit for automatic gearbox - control unit for steering wheel electronicsE438E439F189J527-solenoid valve 1 solenoid valve 2 solenoid valve 3 solenoid valve 4 solenoid valve 5 solenoid valve 6 magnet for selector lever lock solenoid valve 9 solenoid valve 10 magnet for selector lever lock PJ519a J518 F41aJ518Additional signals F41 J518 J519 1 2 3 - reverse gear switch - control unit for access and start authorisation - control unit for on-board network Self-diagnosis CAN data bus high CAN data bus lowF125 N380 F3193152 30G182G195G193G194p + +p123J217N110G93N88N89N90N91N92N93N282N283300_03253 Self-diagnosisDiagnosticsFor vehicle diagnostics, measurement and information systems VAS 5051 and VAS 5052, the operating modes – Guided error search and – Mobile vehicle self-diagnosis are availableThe operating mode ”Guided error search” carries out a vehicle-specific check of all installed control units for incorrect entries and automatically compiles an individual checking plan from the results. Together with the ELSA information, such as circuit diagrams or repair guidelines, this provides a specific target for trouble-shooting. Independent of this, you can compile your own checking plan. The function and component selection incorporates the checks that you select into the checking plan; these can be processed in the continued diagnostics procedure in any order.VAS 5051300_060Although the ”Vehicle self-diagnosis” operating mode can still be used, ELSA no longer provides any additional information.IrDAWO R KS H O P EQUIPMENT+-VAS 5052300_084VAS 505254 ServiceNew tools Setting gauge for multifunction switch T10173 This is required to set the multifunction switch when repairs are completed.300_076Pressure piece T10174 This is required to knock in the gaskets on the shaft for the multifunction switch.300_077Pressure piece T10180 This is required to knock in the gaskets of the drive shaft.300_078Sleeve T10186 This must be placed on the serration of the drive shaft before the gasket is attached to prevent damage during attachment of the gasket.300_07955 Service.300For internal use only © VOLKSWAGEN AG, Wolfsburg All rights reserved. Technical specifications subject to change without notice. 000.2811.20.20Technical status 08/02❀ This paper was produced fromchlorine-free chemical pulp.