TECHNICAL DOCUMENTATION

SSP 307 The Touran Electrical system

PDFEN60 pages3 MB
SSP 307 The Touran Electrical system - PDF cover

This PDF is currently unavailable.

Read document text
Service.Self-study programme 307The Touran Electrical systemDesign and function The networking technology, used until now only in luxury class vehicles, will be a feature in compact vans, such as the Volkswagen Touran. The control units installed in this system also manage tasks that were previously carried out by relays and switches. In order that these tasks can be fulfilled efficiently, the units have to exchange a great deal of information (data) between each other. Such a high rate of data transfer would only be possible with a large number of cables if standard means were used, such as wiring connections. To keep the number of wiring connections at a manageable level, Volkswagen favours the use of data bus connections on a wider scale.This self-study programme is designed to help you better understand the networking concept of the Volkswagen Touran. It covers the allocation of control units to the various data bus systems, the fitting locations of relay slots, fuses and control units. Furthermore, it describes the various functions of and changes to the diagnosis system.S307_050NEWImportant NoteThis self-study programme explains the design and function of new developments. The contents will not be updated.For the latest testing, setting and repair instructions, please refer to the relevant workshop literature.2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4LIN data bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Onboard power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Data bus diagnosis interface . . . . . . . . . . . . . . . . . . . . . . 24Onboard power supply control unit . . . . . . . . . . . . . . . . . 28Windscreen wiper system. . . . . . . . . . . . . . . . . . . . . . . . . . 38Rear window wiper system . . . . . . . . . . . . . . . . . . . . . . . . 44Dash panel insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Immobiliser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Convenience and infotainment settings . . . . . . . . . . . . . . 54Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Test yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 583 IntroductionFuse boxes and relay slots in vehicle's electrical systemFitting locations The onboard power supply of the Touran is decentralised. For this reason, the fuse boxes and relay slots are installed at various locations in the vehicle. The adjacent diagram shows the various fitting locations.Electrics box on left in engine compartmentBack-up fuse box on left in engine compartment4 Relay carrier on left under dash panelRelay carrier on onboard power supply control unit on left under dash panelFuse box on left under dash panelS307_0015 IntroductionThe networking conceptOverview of networked control units In order that data can be transferred between the control units, these are networked via various data bus systems. The data bus diagnosis interface J533 (gateway) provides the interface for the data buses:J431 T16 J220-Drive train CAN data bus Convenience CAN data bus Infotainment CAN data bus Dash panel insert CAN data bus Diagnosis CAN data busJ533J285Drive train CAN data bus Convenience CAN data bus Infotainment CAN data bus LIN data busCAN data bus line Communications line LIN data bus lineJ503 R J345J412 J519CAN data bus Sensor Dash panel insert CAN data bus Diagnosis CAN data busS307_049J525J255 J162In addition to the CAN data bus, a number of electric components are networked via the LIN data bus.R78J136The data protocols have been changed. Therefore, these control units cannot be exchanged with those of other vehicle models e.g. Touareg or Phaeton.J604J3886 G419J217J104J587J500Key E221 G85 G273 G384 G419 H8 J104 J136 J162 J217 J220 J234 J255 J285 J345 J386 J387 J388 J389 J393 J400 J412 J431 J446 J500 J503 J519 J525 J527 J533 J584 J587 J604 R R78 T16J234G85E221J446J527J400J584J386J387Operating unit in steering wheel Steering angle sender Interior monitoring sensor Vehicle inclination sensor ESP sensor unit Anti-theft alarm signal horn ABS with EDL control unit Seat adjustment control unit Heating control unit Autom. gearbox control unit Motronic control unit Airbag control unit Climatronic control unit Control unit with display in dash panel insert Trailer detector control unit Door control unit, driver side Door control unit, front passenger side Door control unit, rear left Door control unit, rear right Convenience system central control unit Wiper motor control unit Cellphone electronics control unit Headlight range control, control unit Parking aid control unit Power steering control unit Control unit with display for radio and navigation Onboard power supply control unit Digital sound package control unit Steering column electronics control unit data bus diagnosis interface Wiper motor control unit front passenger side Selector lever sensors control unit Auxiliary air heater control unit Radio TV tuner Diagnosis connectionJ393J389G273H8G384S307_0027 IntroductionControl units in drive train CAN data busControl units and fitting locations The adjacent diagram shows the control units that belong to the drive train CAN data bus and associated fitting locations. The data is transferred at a speed of 500 kbit/s. Transfer is made via the orange/black CAN high line and orange/brown CAN low line. To make data transfer more efficient, the CAN lines are entwined.Airbag control unit J234 under centre consoleABS with EDL control unit J104 under bulkhead in engine compartmentMotronic control unit J220 under plenum chamber cover8 Control unit for headlight range control J431 on left under dash panel, on tunnel supportdata bus diagnosis interface J533 under dash panel, above relay carrierS307_003Automatic gearbox control unit J217 in wheel housing9 IntroductionThe control units in the drive train CAN data busControl units and fitting locations Shown in the diagram are the control units of the convenience CAN data bus and their fitting locations. The speed of data transfer is 100 kbit/s. The data is transferred via the orange/green CAN high line and orange/brown CAN low line. Both CAN lines are entwined together.Steering column electronics control unit J527 on steering column switchConvenience system central control unit J393 on right under dash panel, near centre consoleClimatronic control unit J255 in centre console10 Parking aid control unit J446 in rear right side partTrailer detector control unit J345 in rear right side partOnboard power supply control unit J519 under dash panel, on relay carrierDoor control units J386, J387, J388, J389 in doorsS307_004data bus diagnosis interface J533 under dash panel, above relay carrier11 IntroductionThe control units in the infotainment CAN data busControl units and fitting locations The control units of the CAN data bus and fitting locations are shown in the adjacent diagram. The infotainment CAN data bus transfers data at a rate of 100 kbit/s. The CAN high line is orange/purple and the CAN low line is orange/brown. Both CAN lines are entwined together.Cellphone operating electronics control unit J412 on front right in footwellHeater control unit J162 on front right under wing12 Control unit with display for radio and navigation J503 or Radio R in centre consoleS307_00513 IntroductionThe control units in the dash panel insert CAN data bus and in the diagnosis CAN data busThe dash panel insert CAN data bus and the diagnosis CAN data bus are new data bus connections in the Volkswagen Touran.Dash panel insert CAN data bus The data bus transfers data from the dash panel insert to the data bus diagnosis interface. The control unit with display unit in the dash panel insert and the data bus diagnosis interface are the only control units attached to this data bus.Control unit with display unit in dash panel J285Diagnosis CAN data bus Data transfer between the diagnosis connection T16 and the data bus diagnosis interface is via the diagnosis CAN data bus.Rate of data transfer The rate at which data is transferred is 500 kbit/s for both CAN data buses.14 data bus diagnosis interface J533 under dash panel, above relay carrierS307_006T16 Diagnosis connection on left in footwell15 LIN data busThe LIN data bus as sub data bus systemGeneral description A sub data bus system connects control units with their electrical components. Among these components are, for example, control units, switches, sensors, actuators etc. This type of connection and data transfer is used in the Volkswagen Touran for a number of systems. As a sub data bus system, the LIN data bus has an advantage in cost. The designation LIN stands for local interconnect network, and it means that all the associated electrical components are within a set and limited area of the vehicle. It is possible for a number of LIN data bus systems to be installed in a vehicle. They will each have different functions to perform. A LIN data bus system consists of a master control unit and one or more slave control units. The master control unit is also networked with other control units (apart from slave control units) in the vehicle via the CAN data bus. This permits the transfer of data to other LIN data bus systems and other CAN data bus control units.LIN data bus system data bus diagnosis interface J533CAN busLIN data busAnti-theft alarm system horn H8 LIN slaveInterior monitoring sensor G273 LIN slaveConvenience system central control unit J393 CAN user and LIN masterVehicle inclination sender G384 LIN slaveS307_00716 Data transfer The data is transferred at a speed of 1 kbit/s to 20 kbit/s. The rate of data transfer is therefore a maximum of 20% of the rate for convenience or infotainment CAN data buses and is fixed in the software of the LIN master. This transfer is made via data leads that are violet in basic colour with a white identification mark. The cross section of the wire is 0.35 mm2. The LIN data bus is a single wire bus. The data lead is not screened.S307_008Signal level The signal level of the LIN data buses is either close to battery voltage (UB) (recessive level) or earth (0 Volt) (dominant level).U UBRecessive level0Dominant leveltS307_00917 LIN data busMaster control unit The control unit connected via the CAN data bus system performs the master functions in the LIN data bus system. Among these master functions are: - Data conversion of LIN data bus messages to the data format used by the CAN data buses, if and when these messages are required. - The control of data transfer in the LIN data bus and monitoring of the data transfer rate. - The transfer of diagnosis data to the LIN slave control unit. The transfer of data between master and slave is always initialised by the master. A slave is not capable of communicating independently.Master control unitSteering column electronics control unit J527 Users of convenience CAN data bus and master control unit in the LIN data bus18 Slave control unit The slave function could be taken on by control units such as the multi-function steering wheel, actuators such as the anti-theft alarm horn or sensors such as the vehicle altitude sensor. The electronics integrated in the slave control unit evaluate the driver's input via the operating unit buttons in the steering wheel, they convert the input into digital information e.g. "radio louder" and send it when required to the master control unit via the LIN data bus. The sensors also have electronics that transfer the measured values digitally to the master control unit.Slave control unitSteering wheel operating unit E221 Slave control unit in LIN data busS307_01019 Onboard power supplyThe electrics boxFitting location The electrics box can be found on the left in the engine compartment. Description All fuses and relays that safeguard or control components in the engine compartment, are housed in the electrics box (E box). A wiring guide to the interior and back is therefore no longer necessary. Fault finding is simplified, safeguarding is adapted more effectively to the consumers and multiple assignment of fuses is largely avoided.Electrics boxS307_01220 Electrics box In addition to the fuses for components in the engine compartment, the electrics box has the following relays:● ● ● ● ●Power supply relay terminal 15 J329 Power supply relay terminal 50 J682 Glow plug relay J52 Motronic power supply relay J271 Power supply relay J317S307_052Back-up fuse box The back-up fuse box houses fuses for the following:● ● ● ●alternator, electro-mechanical power steering, radiator fan, auxiliary heater.S307_05321 Onboard power supplyThe relay carrier and the fuse box in the interiorFitting location In the interior, on the left under the dash panel, you can find the relay carrier, the relay carrier on the onboard power supply control unit and the fuse box.Relay carrier and fuse box in interiorS307_01322 Relay carrier The relay carrier accommodates additional relays and fuses from optional extras in the vehicle.S307_054Relay carrier on onboard power supply control unit The following relays can be found on the onboard power supply control unit relay carrier.S307_055● ● ● ● ● ●Power supply relay terminal 30G Heated rear window relay J9 Horn relay J413 Double washer pump relay 1 (front) J729 Double washer pump relay 2 (rear) J730 X contact relief relay J59Fuse box Included in the fuse box are the fuses for the electrical components in the vehicle.S307_056For the latest terminal assignment details about the fuse box, please refer to ELSA.23 Data bus diagnosis interfaceThe data bus diagnosis interface J533 Description Due to the high level of network functions, a great deal of data is transferred. To assure the effective exchange of data, several data bus systems are necessary that transfer data between each other. The data bus diagnosis interface connects these data buses together as a gateway interface and makes data transfer possible. This function that was perviously integrated in the dash panel insert or onboard power supply control unit, is now an independent control unit.Data transfer data bus diagnosis interfaceDiagnosis CAN data bus Diagnosis connectionDash panel insert CAN data busDrive train CAN data busConvenience CAN data bus24 Fitting location The data bus diagnosis interface can be found on the left next to the dash panel above the fuse box.S307_014Dash panel insertInfotainment CAN busS307_01525 data bus diagnosis interfaceMaster functions The data bus diagnosis interface J533 manages the master functions for terminal 15 run-on on the drive train CAN data bus and control of the sleep and wake-up modes for the data bus systems.Terminal 15 run-on Certain control units in the CAN data bus need to exchange information even when terminal 15 is off. For this reason, a message is sent to the CAN data bus for actuation of the run-on mode. The control units make a connection from terminal 30 to terminal 15 internally, which allows them to communicate further. In this way, the power steering control unit J500, for example, can communicate with the other control units. The run-on mode can last between ten seconds and fifteen minutes. The run-on period depends on the data that is to be sent. To finish the run-on period, the data bus diagnosis interface initiates the sleep command.Control units that participate in terminal 15 run-on J533 Drive train CAN data busTerm. 30J271J500 J220 J587 Internally switched terminal 15 J217 Key G85 J104 J217 J220 J271 J104S307_047G85Steering angle sender ABS with EDL control unit Automatic gearbox control unit Motronic control unit Motronic power supply relayJ500 Power steering control unit J587 Selector lever sensors control unit J533 data bus diagnosis interface26 Sleep and wake-up modes of the data bus systems When all of the control units of the convenience and infotainment CAN data bus have announced their readiness for stand-by, a control unit will give the signal to 'sleep'. The voltage level of the low signal is 12 V and 0 V for the high signal. Furthermore, it also gives the wake-up signal when the data bus has to be activated, for example, when the doors are unlocked. The data bus diagnosis interface monitors the sleep function. If the drive train CAN data bus does not go into sleep mode, the convenience and infotainment CAN data buses do not go into sleep mode either. If the convenience CAN data bus does not go into sleep mode, the infotainment CAN data bus does not go into sleep mode either.S307_048Sleep modeWake-up signalWake-up mode27 Onboard power supply control unitThe onboard power supply control unit J519Fitting location The onboard power supply control unit can be found underneath the dash panel where it forms a unit with the relay carrier.S307_016Variants The onboard power supply control unit is available on the Midline and Highline variants. The Highline variant is installed in vehicles with fog lamps and/or Xenon lights. All other vehicles are installed with the Midline variant. Retrofitting of fog lamps is only possible when the onboard power supply control unit of the Midline variant is exchanged with the onboard power supply control unit of the Highline variant.Onboard power supply control unitS307_017Relay carrier on onboard power supply control unitThe following figures are approximate and may differ depending on country variations and software.28 Tasks: The onboard power supply control unit actuates and controls the following functions: - Electric load management - Functional readiness The onboard power supply control unit activates the function of the electric sliding/tilting sunroof. - Exterior light control - Turn signal control - Windscreen wipers Conveyance of data bus signals to wiper motor control unit - Rear window wiper - Heated rear window Actuation of the heated rear window is via the onboard power supply control unit when the heated rear window button is pressed and if the alternator provides enough voltage. - Interior light control Terminal 30G, via which voltage is supplied to the interior lights, is activated by the onboard power supply control unit. - Backlight The backlight for the footwell is actuated by the onboard power supply control unit via a pulse width modulated signal depending on the position of the dimmer switch for switches and instruments. - Terminal actuation The onboard power supply control unit controls terminal 75x via an X contact relief relay. Terminal 15 is actuated via the voltage supply relay for term. 15 in the electrics box and on the onboard power supply control unit relay carrier. Terminal 50 is actuated via the power supply relay for terminal 50 in the electrics box. - Dimmer, instrument backlight Term. 58d has a dimming function and supplies the dimmer switches and instruments with voltage. - Fuel pump readiness When the driver's door is opened, the electrical fuel pump is supplied with power by the onboard power supply control unit. As soon as the engine has started, power is supplied by the engine control unit. - Alternator readiness The alternator is made ready by the onboard power supply control unit.29 Onboard power supply control unitElectrical load management The electrical load management assures that there is always enough energy in the battery to turn the engine over. To enable this, the electrical consumers of the convenience system are deactivated. The standard of technical safety remains. To switch off the consumers, the onboard power supply control unit evaluates the engine speed, the battery voltage and the alternator load via the DF signal (dynamo field). From this information and from information about which consumers are switched on with short activation periods, the onboard power supply control unit carries out an evaluation of the onboard power supply load state. Based on this evaluation, the onboard power supply control unit can increase engine speed via the engine control unit. The deactivation of convenience consumers is still possible in the same way. For load management, three different operating modes are recognised. Operating mode 1 Terminal 15 on and alternator activeMeasures: At a battery voltage below 12.7 Volt, the onboard power supply control unit demands an increase in the engine idling speed. At a battery voltage below 12.2 Volt, the following consumers are switched off: Heated seats Heated windscreen Heated exterior mirrors Steering wheel heating Footwell lighting Inner door handle lights Reduction and deactivation of Climatronic Warning and deactivation of infotainment30 Operating mode 2 Terminal 15 on and alternator inactiveOperating mode 3 Terminal 15 off and alternator inactiveMeasures: At a battery voltage below 12.2 Volt, the following consumers are switched off: Reduction and deactivation of air conditioning Footwell lighting Inner door handle lights Entry/exit lights Leaving home Warning and deactivation of infotainmentMeasures: At a battery voltage below 11.8 Volt, the following consumers are switched off: Interior lights Footwell lighting Inner door handle lights Entry/exit lights Leaving home Infotainment, e.g. radioThe differences in deactivation in the various operating modes is in the order of individual consumer deactivation. Furthermore, in operating mode 3, several consumers can be deactivation at once. Deactivation is cancelled when the conditions for deactivation are no longer met.When deactivation takes place, this will be shown in the dash panel insert. In addition, an entry will be made in the onboard power supply control unit fault memory.31 Onboard power supply control unitExterior light control The onboard power supply control unit evaluates the signals directly from the light switch. Information about actuation of the turn signals, main beam and headlight flashing is sent via the steering column electronics control unit J527 to the convenience CAN data bus.Functional diagram FF4 J519 X M25 D E4 Term. 15E19 J527 Convenience CAN data busS307_019Key D E1Ignition/starter switch terminal 15 Light switchE4E19Manual dipped beam and flash switchParking light switchF F4 J519 J527 M25 XBrake light switch Reverse light switch Onboard power supply control unit Steering column electronics control unit High level brake light bulb Number plate light32 Turn signal control If the turn signal switch E2 is pressed once briefly, vehicle direction is indicated by three flashes of the lights. If the switch is pressed again briefly, the three flash sequences are repeated. This is referred to as the lane change function.Pictorial representationFirst actuation Second actuationOperation of turn signal by quick actuation of turn signal switch E2M5 or M7Actuation of turn signal by onboard power supply control unit M6 or M8S307_018Key E2Turn signal switchM5 M6 M7 M8Turn signal bulb, front left Turn signal bulb, rear left Turn signal bulb, front right Turn signal bulb, rear right33 Onboard power supply control unitMonitoring of light switch positions Light switch E1 is supplied with power directly from the battery. Therefore, it sends a fixed plausible signal in every position to the onboard power supply control unit. By way of independent signal input, the onboard power supply control unit can detect whether ignition is switched on or not. If the fixed plausible signal is changed by a fault, such as an open circuit in the wiring, it will change to implausible. The onboard power supply control unit will switch to emergency light control.Signal sequence HeadlightsTerm. 15 Term. NSL Term. NL Term. TFL Term. 56 Term. 58J519E1Term. 30Rear light cluster Key E1 J519 Term. 56 Term. 58 Term. TFLS307_020NSL NLLight switch Onboard power supply control unit Driving lights Side lights Daylight driving lights Function must be coded in onboard power supply control unit Coding differs in each country. Rear fog lamp Fog lights34 Emergency light controlIf the onboard power supply control unit detects a fault with the ignition switched on, the side lights and the dipped beam lights are switched on.Example of light switch plausibility with ignition switched onSwitch position Off Side lights on Driving lights on OffTerminal 58 0V 12 V 0V 0VTerminal 56 0V 0V 12 V 12 VTerminal TFL 12 V 0V 0V 12 VSignal Plausible Plausible Plausible Implausible fault detection Implausible fault detection Implausible fault detection Implausible fault detectionOff0V0V0VOff12 V12 V0VOff12 V12 V12 VIn the case of all faults, an entry is made in the fault memory.35 Onboard power supply control unitBulb monitoringThe function of the bulbs is monitored constantly. This monitoring takes place when the ignition is off (cold monitoring) and when the ignition is switched on (warm monitoring).Cold monitoring The individual bulbs are supplied with a minimal charge four times for 500 ms when the ignition is switched on. This level of voltage enables the onboard power supply control unit to detect whether any of the bulbs are blown.mAS307_021Warm monitoring The actuation of the individual bulbs is via semi-conductor components that are housed in the onboard power supply control unit. They can detect overloads, short circuits or open circuits.mAS307_022Fault detection With both types of monitoring, once a fault is detected an entry is made in the fault memory and a fault warning is also displayed in the dash panel insert. A new bulb will be detected by the monitoring system once installed, the fault will be erased and the display cancelled.S307_02336 Additional bulb functionsVarious bulbs are dimmed to take on additional functions. If their proper function is needed, this is given priority.Bulb Dipped beam, left and rightAdditional function Dimmed daylight driving lights, left and rightBulb Brake light, left and rightAdditional function Dimmed rear lights, left and right approx. 18 %Rear fog lamp left and right country-specificDimmed rear lights, left and right approx. 12 %Additional function: Brake light as rear light Dimmed actuation of brake lightsOnboard power supply control unitActuation of brake lights for brakingRear light clusterS307_024Please observe the country-specific variations in the rear fog light function.37 Windscreen wiper systemWiper motor actuationWindscreen wiper motor actuation The wiper system consists of a twin motor opposing action system without a mechanical connection between the wiper arms. The switch position of wiper switch E is sent directly to the steering column electronics control unit J527 and then via the convenience CAN data bus to the onboard power supply control unit J519. Information about the selected wiper stage is sent from the onboard power supply control unit via the LIN data bus to the wiper motor control unit J400 and from there to the wiper control unit, front passenger side J584. Both control units are located directly on the wiper motors. The wiper motor control unit J400 manages control of the wiper motion and regulates the wiper control unit, front passenger side J584.Actuation of wiper motorsDrive train CAN data Dash panel insert bus CAN data bus Ambient temperature Road speedDJ584 Term. 15 J400 LIN data busF266 E J519J527 J533 Convenience CAN data bus Key D E F266 J400 J519 Ignition/starter switch Wiper switch Bonnet contact switch Wiper motor control unit Onboard power supply control unitS307_025J527 Steering column electronics control unit J533 data bus diagnosis interface J584 Wiper control unit, front passenger side38 Wiper functions The wiper system features the following functions: Service and winter position Alternating rest position Speed dependent wiper stage reset Speed dependent intermittent delay Bonnet contact Synchronisation function Tip wiping stage 2 Prewash Follow up wash after wash/wipe function Trickle wipe Anti-blocking function Wiper control for rear windowService and winter position If within 10 seconds after switching off the ignition, and with the vehicle stationary, the wiper switch is switched to the tip wiping position, the wipers move to the upper arc position. This function cannot be selected when the bonnet is open.S307_026Service and winter position39 Windscreen wiper systemAlternating rest position In order to prevent a permanent deformation of the wiper blades, the wiper arms move upwards slightly every second time they are switched off. In this way, the position of the wiper blades is changed. In addition, the rest position can also be altered by switching the ignition off several times.S307_027Rest position after switching off first timeRest position after switching off second timeSpeed dependent wiper stage reset If the road speed drops below 4 km/h, the selected wiper speed will be reduced by one stage. When road speeds increases above 8 km/h, the wiper speed is reset to the selected stage. Resetting: Stage 2 to stage 1 - Terminal 15 on - Wiper switch at stage 2 - Road speed 4 km/hS307_028For reasons of clarity, only the driver's wiper is shown.Stage 1 to intermittent operation stage - Terminal 15 on - Wiper switch at stage 1 - Road speed 4 km/h (Intermittent delay 4 s)40 Speed dependent intermittent delay The speed of the four adjustable intermittent phases is dependent on the road speed of the vehicle. The delays between the individual wiper movements vary from 1.28 seconds in stage 1 at approx. 150 km/h to 24 seconds in stage 4 at approx. 4 km/h.S307_0294th stage 3rd stage 2nd stage 1st stageBonnet contact switch F266 If when the vehicle is stationary the bonnet is opened, the wiper motor control unit J400 switches the wipers off. If the bonnet was not closed correctly and opens at a speed of 2 km/h to 16 km/h, the wiper motor control unit J400 switches the wipers off in the same way. The isolation function can be cancelled again by operation of the wiper switch. At speeds greater than 16 km/h, the isolation function is not active. The signal is sent from the bonnet contact switch directly to the onboard power supply control unit and is then sent on further via the LIN data bus to the wiper motor control unit.Bonnet contact switchS307_03041 Windscreen wiper systemSynchronisation function If the windscreen wipers are not in their rest position when the ignition is switched off, these will be moved automatically to the rest position when the ignition is switched on and when the wiper switch E4 is actuated. This is either a parallel or individual movement. A system with an unsynchronised rest position is set straight with this procedure.S307_031Wiper paths during synchronisationTip wiping stage 2 If the tip wiping function is actuated for longer than two seconds, the wiper is switched to the second stage.S307_03242 Prewash When the wash/wipe function is actuated at speeds less than 120 km/h, the wiper will begin to operate after a prewash period of approx. 0.8 seconds, during which only the washer pump is active.Follow up wash after wash/wipe function If the wash/wipe function is actuated for longer than 0.5 seconds, the follow up wiping function is actuated three times. If actuation time is less, follow up wiping is actuated twice.Trickle wiping If the road speed of the vehicle is greater than 2 km/h, the wiper function is actuated once more 5 seconds after the last follow up wash (follow up wiping cycle).S307_033Anti-blocking function The wiper system detects if the wipers are blokked by the amount of current that is drawn. If there is a blockage in area A, it will attempt to remove this a total of five times. If it is unable to move the blockage, the wipers will remain in the rest position. The blockage will have to be removed manually. If the wiper blades are frozen to the bottom part of the windscreen, the wipers will attempt to break free a total of five times. After the fifth attempt, there will be no wiper motion.BlockingAS307_03443 Rear window wiper systemRear window wiper control Rear window wiper actuation features three operating modes: - Reverse wiping - Rear intermittent wiping - Rear window wash/wipe operation Conditions for activation: - Ignition switched on - Windscreen wiper is in intermittent stage 1 or stage 2 Recognition of the selected stage is via the convenience CAN data bus. The signal comes from the steering column electronics control unit. - Reverse gear or R selected Recognition is via the reverse light switch or via the gear selector position, the automatic gearbox control unit, the drive train CAN data bus, the data bus diagnosis interface and the convenience CAN data bus. - Tailgate closed Recognition is via the convenience system central control unit.Reverse wiping The reverse wiping function actuates the rear window wiper to clear the screen if, when the front windscreen wiper is switched on, reverse gear is selected. Intermittent stage Stage 1 or 2 One wipe Rear intermittent wipeSignal pattern of rear window wiperDrive train CAN data bus D Information about selected reverse gear Term. 15 J519 EV12J393J527 J533 Convenience CAN bus Key D E J393 J519S307_035Ignition/starter switch Wiper switch Convenience system central control unit Onboard power supply control unitJ527 Steering column electronics control unit J533 data bus diagnosis interface V12 Rear window wiper motor44 Rear intermittent wiping If the rear intermittent wiper stage is selected, the rear window wiper operates in delayed stages. Conditions for activation: - Ignition switched on - Rear window intermittent wiper stage on: Recognition is via the wiper switch, the steering column electronics control unit and the convenience CAN data bus. - Tailgate closed Recognition is via the convenience system central control unit.S307_036Rear window wash/wipe operation In rear window wash/wipe operation, the double washer pump delivers washer water to the rear window and the rear window is cleared. Conditions for activation: - Ignition switched on - Rear window wash/wipe operation stage on: Recognition is via the wiper switch, the steering column electronics control unit and the convenience CAN data bus. - Tailgate closed: Recognition is via the convenience system central control unit.S307_03745 Dash panel insertControl unit with display unit in dash panel J285Control lamps and displays The control unit with display unit in the dash panel insert actuates the display, the analogue display instruments and the control lamps.Dash panel insert LED control lamps Display, digital screenS307_038Rev counter, analogue display Coolant temperature, analogue displaySpeedometer, analogue display Fuel gauge, analogue displayThe coolant temperature display on vehicles with map controlled cooling is at a constant 90 °C at coolant temperatures between 75 °C and 107 °C. The display on vehicles without map controlled cooling is at a constant 90 °C at coolant temperatures between 75 °C and 115 °C. This way, a continually changing figure in the display is avoided.46 Display The following variants are designed for the display: Lowline with displays forLowline variant20:14km trip-Clock Mileage reader Trip counter Selector lever position20375167.5PRN DSMidline variant3S307_039Midline with additional displays to Lowline variant - Ambient temperature - Multi-function display or - Warning messages instead of multi-function display and ambient temperature20:14 7.8 ltr./100 km 13.5 C°km trip20375Highline with additional displays to Midline variant - Sender display - Warning symbols instead of multi-function display and ambient temperatureHighline variant167.5P R N D S 2S307_04020:14 7.8 ltr./100 km 13.5 C°km trip20375167.5PRN DS3S307_04147 Dash panel insertEquipment with control lampsSymbol Control lampAirbagLowlineXMidlineXHighlineXWarning message or warningAirbag fault Airbag belt tensioner deactivatedABSXXXABSBrake pad wearXXPictogramCheck brake padLow brake fluid levelXXXStop - Brake fluid See manualPreglow period (diesel engines) Dynamic oil pressure warning Electronic power control EPC Electronic power steering Electric brake pressure distribution Parking brake systemXXXTurn signalTurn signalTurn signal pictogram XStop - Oil pressure - Engine off See manualXXXXXXXXWarning buzzer (3 times)XXXHandbrake appliedESP TCS Left turn signalXXXXXXAcoustic checkRight turn signalXXXAcoustic checkTrailer turn signalsXXXMain beam headlightsXXX48 SymbolControl lampCruise control systemLowlineXMidlineXHighlineXWarning message or warningBulb failureXXXe.g. Front left dipped beam light defective e.g. Tailgate openTailgate door open Fuel reserveXXPictogramXXPictogramPlease fill up Warning buzzer (once) Stop - Check coolant See manual Warning buzzer (3 times)Low coolant level or overheating AlternatorXXPictogramXXXEngine check EOBD Bonnet openXXXEngine fault - Workshop Exhaust gas - Workshop Door warning! Bonnet! Warning buzzer (once) if v 6 km/hXXPictogramRear fog lightXXXOil levelXXPictogramCheck oil level Oil sensor - Workshop Warning buzzer (once)Tyre pressure monitorXXXShift lockXXXSeatbeltXXXPlease apply seatbelt Gong Replenish washer water Warning buzzer (once) Immobiliser active Warning buzzer (once)Low washer waterXXPictogramImmobiliserTurn signalTurn signalTurn signal49 ImmobiliserThe fourth generation immobiliserControl unit The immobiliser control unit J362 can be found in the dash panel insert, as with immobilisers of the third generation. The diagnosis connection is made via address word 25. Communication is only possible via the diagnosis CAN data bus with vehicle diagnosis, testing and information system VAS 5051.DiagnosisDash panel insert CAN data bus VAS 5051 Diagnosis CAN data busJ285T16J533VAS 5051/5AS307_042Key J285 J533 VAS 5051 VAS 5051/5A T16Control unit with display unit in dash panel insert data bus diagnosis interface Vehicle diagnosis, testing and information system Diagnosis lead 3 m Diagnosis connection50 Changes compared to the third generation immobiliserBrand identification The immobiliser components of all Group brands are different. Adaption of components from other Group brands in Volkswagen vehicles is not possible.S307_043Preprogrammed key The vehicle keys are preprogrammed by the manufacturer with a basic code. This basic code includes a specific manufacturer code. Matching the key to a vehicle is only possible if it has the correct manufacturer code.Basic codeS307_04451 ImmobiliserMatching Enabling the matching function is done via the vehicle diagnosis, testing and information system VAS 5051. The personal identification number (PIN) for matching is currently available via the dealer online access system (HOLZ). In future, matching will be carried out via an online connection.Exchanging the engine control unit The engine control unit is enabled in the same way as the third generation immobiliser. Two of the three adapted components (key and dash panel insert) must remain in the vehicle. For adaption of a new control unit, this can be done without a personal identification number. For adaption of a control unit that was previously installed in a different vehicle, a personal identification number is required.52 Exchanging the dash panel insert Adaption is carried out in the same way as for the third generation immobiliser. Likewise, two of the three adapted components (key and engine control unit) must remain in the vehicle. For adaption of a new dash panel insert, this can be done without a personal identification umber. A personal identification number is required for a previously used dash panel insert. Following exchange, the immobiliser control unit J362 will detect an unknown key. For this reason, there is a blocking period of five minutes during which time the engine cannot be started.With the exchange of more than one component, all three items must be renewed as less than two of the matched components are left in the vehicle.53 Convenience and infotainment settingsPersonalisationThe user based settings for different unit functions in the convenience and infotainment system are made via an operating unit and a display. Operation is via a control lever on the steering wheel. Selection from the menu is made via the display in the dash panel insert. The settings selected are stored in the control unit, which is responsible for the control of each function. Transfer of the necessary information between the control unit with display unit in dash panel insert and the other control units is managed by the CAN data bus.Steering column switchJ285 J533J527J519 Key J162 Heater control unit J285 Control unit with display unit in dash panel insert J393 Convenience system central control unit J519 Onboard power supply control unit J527 Steering column electronics control unit J533 data bus diagnosis interfaceJ393J162S307_045For precise details on operation, please refer to the operating instructions.54 LightingHeadlightsOne touch attachment The H7 bulbs are connected to the reflector by means of a one touch attachment. The old means of attachment with clip and electrical connector has been discontinued. By means of one touch, the attachment of the bulbs can be released with a twisting action.S307_064Release from attachment by twisting to leftThereafter, the bulb is pulled out of the attachment.S307_060Pull bulb out of attachmentThe functional description of the Bi-Xenon headlights that are installed can be found in SSP 251 "The Passat 2001". The procedure for renewing a bulb can be found in ELSA.55 ServiceDiagnosisThe transfer of data necessary for diagnosis to vehicle diagnosis, testing and information system VAS 5051 or vehicle diagnosis and service information system VAS 5052 is via the diagnosis CAN data bus. Data transfer to VAS 5051 is only possible via diagnosis leads VAS 5051/5A or VAS 5051/6A. For vehicle diagnosis and service information system 5052, diagnosis lead VAS 5052/3 should be used. These diagnosis leads are suitable for the transfer of data via the diagnosis CAN data bus. The COM lead used until now is still required for diagnosis of the engine and gearbox control units in OBD mode. Therefore, diagnosis with other diagnosis leads is only possible in the engine control unit and automatic gearbox control unit.VAS 5052 VAS 5051/6AVAS 505156 J285Dash panel insert CAN data busVAS 5051/5ADiagnosis CAN data bus J533 T16Communications lineDrive Train CAN data bus VAS 5052/3Convenience CAN data busInfotainment CAN data busS307_051Key J285 J533 T16 VAS 5051 VAS 5051/5A VAS 5051/6A VAS 5052 VAS 5052/3Control unit with display unit in dash panel insert data bus diagnosis interface Diagnosis connection Vehicle diagnosis, testing and information system Diagnosis lead 3 m Diagnosis lead 5 m Vehicle diagnosis and service information system Diagnosis lead 3 m57 Test yourself1. Which data bus systems are used in the Volkswagen Touran?… a) The CAN data bus and the LIN data bus. … b) The MOSFET data bus, the LIN data bus and the MOST bus. … c) The D2B data bus, the A data bus and the CAN data bus.2. Where can the data bus diagnosis interface be found?… a) In the dash panel insert. … b) Under the centre console next to the airbag control unit. … c) Under the dash panel above the relay carrier.3. Which control units belong to the dash panel insert CAN data bus?… a) The onboard power supply control unit, the automatic gearbox control unit and the trailer detectorcontrol unit.… b) The control unit with display unit in dash panel insert and the data bus diagnosis interface. … c) The Motronic control unit and the diagnosis connection.4. The LIN data bus transfers data at a rate of… a) 1 kbit/s to 20 kbit/s. … b) 100 kbit/s to 500 kbit/s. … c) 21 Mbit/s.58 5. Which functions are controlled by the onboard power supply control unit?… a) Turn signal control, heated rear window, fuel pump readiness. … b) Windscreen and rear window wipers, central locking, instrument illumination. … c) Load management, alternator readiness, starter isolator.6. What is the main role of the load management system?… a) To ensure that there is always enough electrical power to turn the engine over. … b) With electronic charge indication, it warns the driver when the vehicle is overcharged. … c) It prevents overloading of the engine by irregular operation.7. What must be observed when operating the vehicle diagnosis, testing and information system VAS 5051 on the Touran?… a) For diagnosis, only diagnosis leads VAS 5051/5A and VAS 5051/6A should be used. … b) Diagnosis can be carried out in all areas using V.A.G 1551 or V.A.G 1552. … c) Diagnosis is only possible using VAS 9119.Answers: 1. a 2. c3. b4. a5. a, c6. a7. a59 307For internal use only © VOLKSWAGEN AG, Wolfsburg All rights and the right to make technical alterations reserved 000.2811.27.20 Technical status 02/03❀ This paper was manufactured from pulp thatwas bleached without the use of chlorine.