TECHNICAL DOCUMENTATION
SSP 321 The Golf 2004 Running gear

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study programme 321The Golf 2004 Running gearDesign and functionWith the refined safety running gear of the Golf, which is configured for both sporty and comfortable driving, VW has set a further standard in the development of running gear technology. With the aim of developing the best underpinnings in its class, a dynamic running gear system was created that keeps the driver away from unpleasant surprises in any situation.The running gear of the Golf features an optimised suspension strut axle, multi-link rear axle, completely new electronic power steering and the newest generation of ESP and brake assist system to offer a unique synthesis of best-in-class driving comfort and, at the same time, best steering and driving response.S321_179NEWImportant NoteThis self-study programme shows the design and function of new developments! The contents will not be updated.For current inspection, adjustment and repair instructions, please refer to the relevant service literature.2ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Front axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Rear axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Brake system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Wheels and tyres. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35Foot pedal cluster . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Test yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433IntroductionThe running gearOnce again, the running gear of the Golf sets a standard in its class. To achieve this a suspension strut axle, perfectly optimised in many ways, has been installed. With regards to driving dynamics and driving comfort, the new four link rear axle is also ground-breaking. The electromechanical power steering of the Golf supports the vehicle's driving characteristics in a remarkable way. To do this, it transmits a precise steering feeling and adapts the steering forces harmoniously as speed increases. In addition to the Golf, the Touran and Audi A3 also currently use this running gear platform.●Floor mounted accelerator pedal with non-contact accelerator pedal position senders●Optimised suspension strut axle based on the McPherson principle●Direct anti-roll bar connection with ratio of 1:1●Electromechanical power steering●Brake servo with dual rate map characteristic●Electronic stabilisation program based on MK 60 system from Continental Teves4The Golf can be equipped with standard, sports or heavy duty running gear. The various running gear systems differ in the spring, damper, anti-roll bar equipment and the mounting elements. The sports running gear is lowered by 15 mm compared with the agile and comfort-orientated standard running gear. The body height of the vehicle with heavy duty running gear is 20 mm higher than on the standard running gear version.●Four link rear axle●4motion drive, optional●Tyre monitoring system, optional●Brake assist system●Track and camber on rear axle can be adjusted separatelyS321_135●Wheel designs in 15", 16" or 17" versions5Front axleThe front axleThe Golf has a McPherson front axle with bottom wishbones and wheel locating suspension struts. The front axle offers optimal comfort at a high level of stability.Anti-roll barSubframeSuspension strutWheel bearing Wishbone suspension Console housingCoupling rodS321_007Wheel bearing6SubframeConsole Subframe Console S321_022The subframe comprises of three parts and is made of aluminium. It is joined to the body at six points. With this type of connection, the body is stiffened in the front area. The optimal layout of the bonded rubber bushes in the wishbones and suspension strut mountings has a positive influence on the driving dynamics and body acoustics.Key: = Bonding point to bodyWheel bearingThe wheel bearings are of the 3rd generation. This type of component is a compact wheel bearing unit comprised of wheel hub and wheel bearing, which is bolted from the interior to the swivel mounting by four bolts. The advantage of this wheel bearing is that the bearing play no longer has to be adjusted.S321_0207Front axleSuspension strut The spring used is a combination of cylindrical coil spring and polyurethane auxiliary damper. The coil spring is made from high tensile steel and is drawn in at the ends. The damping characteristic of the coil springs is linear. The polyurethane auxiliary spring has a progressive damping characteristic.Auxiliary damperCoil springS321_039Suspension strut mounting The suspension strut mounting is a bonded rubber bush. By decoupling the spring and shock absorber connection to the body, the damping force is absorbed separately by the body. In this way, pretension in the damper mounting is prevented. This positively influences rolling comfort and reduces the transfer of noise from the road surface to the body. The mounting features a soft damping characteristic in the direction of normal travel. In this way, an improvement is achieved in driving comfort and acoustics. In the lateral direction, the mounting is designed to be stiffer. This measure positively influences the driving dynamics and the steering response.S321_0418Swivel mounting The swivel mounting is joined to the suspension strut by a clamp-type connection. At the lower level it is attached to the wishbone via a guide joint. The wheel bearing unit is bolted to the swivel mounting. Depending on the version, either a bolted or integrated swivel mounting is installed.Integrated swivel mountingBolted swivel mounting Swivel mountingClamp-type connectionSuspension strut Swivel mountingSuspension strut Clamp-type connectionBrake carrierBrake caliperS321_019S321_043Wheel bearing unitGuide jointWheel bearing unitBolted connectionWishbone suspension The wishbones form the lower connection between the body and swivel mounting. Depending on the engine, they are made from cast iron or sheet metal and are joined via bonded rubber bushes to the consoles of the subframe.SubframeWishbone suspensionS321_0219Front axleAnti-roll bar The tubular anti-roll bar is joined directly to the suspension strut via a coupling rod in a ratio of 1:1. The advantage compared to the Golf’98 is that a higher degree of anti-roll stabilisation is achieved with the same tube diameter.Suspension strutBushesCoupling rod Anti-roll barSubframe S321_045The anti-roll bar is mounted on the subframe by means of two bushes. The positive connection of the bonded rubber bushes prevents relative movements between anti-roll bar and bonded rubber bush. Instead of turning in the rubber bush, the rotational movements of the anti-roll bar are absorbed in the mounting. In this way, a high degree of efficiency is achieved.Anti-roll barBonded rubber bush S321_134 Absorbed relative movement Bearing10The drive shaftsLeft-hand drive shaftRight-hand drive shaftS321_046Intermediate shaftS321_048Installed in the Golf is the track proven drive shaft concept with short and long drive shafts. The shorter shaft on the left-hand side is solid. The longer shaft on the right, however, is a hollow tubular construction.On higher powered engines, the drive shafts are of the same length. This is made possible by an intermediate shaft, which is mounted additionally on the crankcase. This drive shaft concept is advantageous in that, even during full acceleration, there are no repercussions on the steering and straight running of the vehicle from driving forces. Furthermore, pulling to one side is also avoided.Intermediate shaftS321_04911Rear axleThe front wheel drive rear axleThe rear axle of the Golf is of the compact four link design. On each side it has three suspension links (lower link, track rod and upper link) and a trailing arm. This layout means that longitudinal and lateral forces are almost completely separated from each other. In this way, a very high level of driving stability and comfort are achieved. With a predetermined alteration in the wheel position during cornering, a light understeer is achieved due to the natural opposing steering force of the outer wheel (self steering response or toe-in steering).Steel spring Anti-roll bar Damper Upper linkSubframe Bearing bracket Track rodLower link Trailing armS321_17112Subframe The subframe is a welded construction made from steel. It is bolted directly to the body. The body mounting points on front wheel drive and 4motion drive systems are identical.S321_027Wheel carrier The wheel carrier is a forged metal construction made from steel with a moulded stub axle to mount the wheel bearing.Wheel bearing The wheel hub and wheel bearing form one component. The wheel bearing is bolted to the stub axle of the wheel carrier by means of a stretch bolt. In this way, the necessary bearing preload is achieved (2nd generation wheel bearing).Stub axleWheel bearingWheel carrierStretch boltS321_02913Rear axleFour link principle On the four link axle of the Golf 2004, longitudinal and lateral connections are separate. The advantage is that no compromise had to made between comfort and driving dynamics. The front mounting (trailing arm) is not subjected to lateral forces and has therefore been made very soft. Cracks and grooves running across the road surface are absorbed easily.LongitudilalTrailing armTrack rodLateral forceTop linkBottom linkS321_018As a comparison, the following illustration shows the force distribution on the double wishbone suspension of the Golf’ 98.Longitudinal forceTrailing armUpper wishbone Lateral forceLower wishboneS321_19014The 4motion rear axleThe driven rear axle has been modified on the subframe, anti-roll bar, wheel carrier and wheel bearings. The advantage of this axle design is that the floor assembly on vehicles with front wheel and 4motion drive systems is the same with regards to the body mounting points.Subframe Wheel bearingAnti-roll barS321_031Wheel carrier15Rear axleSubframe The subframe is a welded construction made from aluminium. It also supports the rear differential. It is bolted to the body by means of oversized bonded rubber bushes. In this way, noise reduction is promoted thanks to isolation of the body. An additional aluminium cross member, bolted in position, serves as a means of increasing rigidity in the lower area by complementing the subframe. The use of aluminium means that a weight saving of approx. 7 kg has been achieved.SubframeCross memberS321_033Bonded rubber bushWheel carrier The wheel carrier was modified geometrically to accommodate the drive from the rear axle (introduction of modified wheel bearing and drive shaft).Wheel bearing The wheel bearing installed here is of the 3rd generation (as installed in the front axle).Wheel carrierWheel bearingS321_03516SteeringThe steeringThe electromechanical power steering supports the driving response of the Golf. To do this, it conveys a precise feel for the vehicle and the road. As speed increases, the steering forces are adapted harmoniously. Disrupting factors from bumps in the road surface are filtered out as far as possible.OverviewSteering columnSteering wheelS321_053Universal joint shaftElectromechanical power steering17SteeringThe steering wheelsInstalled as standard is a 4-spoke PU steering wheel. PU (polyurethane) is a very strong synthetic material, which is good to work with and can be recycled. As an alternative, a steering wheel with soft leather covering and one-piece cast magnesium frame is available. During assembly, the airbag module is installed in the steering wheel mechanically and can only be removed if the steering column is disengaged. This is an effective anti-theft measure to prevent unauthorised removal of the driver airbag.S321_124The steering wheel features a weight-optimised framework cast from magnesium. The design can be seen in the cross sectional diagram of the multi-function steering wheel.Cross-section based on wooden steering wheelMounting for left multiLeather covering of left spoke trim function switch Mounting for right multi-function switch Leather covering of right spoke trimWood veneer shellLeather coveringMagnesium frame S321_196PU foam coveringSheet metal plate18Various designs of 3-spoke steering wheel will be available as an option.Design 1: The steering wheel is of the 3-spoke design, finished in either leather or a combination of leather and aluminium.S321_012Design 2: The steering wheel is of the 3-spoke design, finished in wood and leather. The multi-function steering wheel features an audio and telephone function.S321_014Design 3: The steering wheel is of the 3-spoke design, finished in leather. The multi-function steering wheel features an audio and telephone function and also Tiptronic.S321_01019SteeringThe steering columnThe reach and rake adjustment of the steering column is mechanical. For optimal adaptation to the driver's requirements, it can be adjusted up and down by 50 mm and back and forth by 60 mm. Fixing of the steering wheel in position is by means of a multi-plate bundle with ten steel plates. Five plates in the horizontal plane make reach adjustment possible. The other five plates are installed in the vertical plane and make rake adjustment possible.Multi-plate bundle for reach adjustmentMulti-plate bundle for rake adjustment S321_084Connection of the steering column to the dash module carrier is by means of an assembly bracket pressure cast from aluminium.20Principle of the clamping function The clamping function is provided by two rollers that are pushed up a ramp to fix the steering wheel in position. In this way, the multi-plate bundle is pressed together via a thrust piece. Due to the fact that no gear teeth are used in the clamping mechanism, adjustment is infinitely variable.●Multi-clamp bundle releasedThrust piece Plates for rake adjustment RollerRamp Plates for reach adjustmentS321_128●Multi-clamp bundle clampedThrust piece Plates for rake adjustment RollerRamp Plates for reach adjustmentS321_12621SteeringCrash concept As part of occupant safety, the steering column and the universal joint shaft are designed to slide into each other. In this way, the steering column and the steering wheel will not be pushed towards the driver if the front end of the vehicle deforms. The steering column tube and universal joint shaft are designed so that the steering column is decoupled from the steering gear in the event of the steering gear being forced inwards in a crash. This prevents the steering wheel from jutting against the driver as a result of further deformation of the front end.S321_130The cradle and console are joined together by means of a shear plate. In the event of a crash, a defined force is placed against the shear plate by the movement caused from the impact of the driver against the cradle.The geometrical design of the shear plate means that a progressive force/travel characteristic is achieved.CradleShear plateS321_173 Console22The electromechanical power steeringThe Golf is fitted as standard with an electromechanical power steering system. This steering system consists of steering box and an electric motor with control unit. The system is installed on the subframe. The steering assistance from the electric motor, which is flanged in parallel to the toothed rack, is transmitted via a second pinion (drive pinion) to the toothed rack.S321_137The electro-mechanical power steering is an active steering system, which is directly dependent on road speed, the steering force and the steering angle.Data is transferred via the drive train CAN data bus. The control unit is flanged to the electric motor.Control unit Steering force sender Electric motorSteering pinion Toothed rack Steering column Drive pinionS321_057Steering angle senderFurther information can be found in SSP 317 "The dual pinion electromechanical power steering".23Brake systemThe brake systemThe basis for good braking properties is provided by a newly designed brake system. The Golf is fitted as standard with the newest generation of ESP and brake assist system.OverviewBrake servoESP unitS321_155 Rear wheel brakeBrake cable HandbrakeFront wheel brakeBrake lines24The brake equipmentEngine 55 kW85 kW Front brakes (single piston floating caliper brake) Rear brakesØ280x22Ø255x10Ø260x12S321_156Integrated swivel mounting 100 kW110 kW and 77 kW TDI with DSG 02E Ø288x25S321_164 S321_166S321_158bolted swivel mounting 147 kW and 118 kW TDI Ø312x25Ø286x12 / Ø286x12S321_168 S321_160bolted swivel mounting 177 kW Ø345x30 Ø310x22S321_170 S321_162bolted swivel mounting25Brake systemThe dual rate booster brake servoIn all left-hand drive vehicles, a 10" brake servo is installed. Right-hand drive vehicles are equipped with a tandem brake servo of 7/8" in dimension. A main new feature is the introduction of the "dual rate characteristic". The inside of the brake servo is modified, which results in a progressive characteristic. In this way, higher brake pressures are available than on conventional brake servos, even at low pedal forces. Braking forces are still imparted softly during normal operation however.S321_078Standard characteristic Dual rate characteristicBrake pressurePedal forceS321_03726The anti-lock braking system ABS/ESP Continental/Teves MK 60A new ESP unit of the product family MK 60 is installed. The main new features are:●Active wheel speed sender without forwards and reverse travel recognition.●Combined yaw rate/lateral acceleration sensor. This sensor is compatible with the CAN system.●Installed in the ESP unit is the brake pressure sender. The brake pressure sender was installed until now on the tandem brake master cylinder. New ESP warning lamp.●S321_192Hydraulic unit with brake pressure sender (G201)S321_060Sender spring contactsBrake pressure senderInstalled as an exclusive ABS system is the MK 70. As this component only features the ABS function (4 inlet and 4 outlet valves), it is smaller and lighter than the MK 60 system.27Brake systemThe brake pressure sender (G201)It measures the pressure applied at the brake pedal by the driver. To ensure a higher level of safety, the sensor supplies two pressure signals independently of each other. These are sent at the same time as two opposing voltages. The control unit constantly compares these with each other.S321_176S321_178S321_175 1. Measuring chamber 5. Piezo resistive measuring bridge 6. Flexible thick film membrane 7. Piezo bridge elements within measuring bridge2. Piezo resistive thick film sensor element 3. Sensor electronics and signal amplifier 4. Contact springs to control unit J104Electric switching The sensor is joined via 4 contact springs to control unit J104 (4). Two contacts serve as a means of supplying power, the other two provide two independent pressure signals.28Construction The sensor works on the principle of piezo resistance. To do this, use is made of the change in conductivity of the materials from structural deformation. Four piezo resistive measuring elements, which are switched together to form a bridge (5), are installed on a membrane (6). Piezo resistive measuring elements are resistors made from semi-conductor material. The function is similar to that of bi-metallic strips.Function As pressure increases, the length of the membrane (6) changes and also the piezo resistive measuring bridge (5) connected to it. This change in length imparts force on the piezo bridge elements in the measuring bridge (7), which alters the charge distribution within the piezo elements. With a change in the charge distribution, the electrical properties of the piezo bridge elements also change. These are proportional to the pressure and are transmitted as an amplified sensor signal to control unit J104.Self-diagnosis The pressure sensor is monitored by the electronic control unit via both output signals. If both signals deviate from each other within the tolerance level, a fault is diagnosed by the control unit.Effects of failure In the event of pressure sensor failure, the ESP function is reduced to ABS and EBD (electronic brake pressure distribution).29Brake systemThe optimised hydraulic brake servo (OHBS)The most effective way to supply vacuum pressure to the brake servo is to utilise the vacuum from the intake manifold on the engine. On petrol engines with automatic gearboxes, the vacuum pressure available at the intake manifold can drop significantly in certain operating conditions (cold start phase). This can have a negative impact on the comfort of brake actuation. The cause of this is the opening of the throttle valve under load, which drastically reduces the vacuum in the intake manifold. Until now, the necessary vacuum for such situations was provided by an auxiliary unit (e.g. electric vacuum pump). In the Golf 2004, a new path has been found.Map characteristic at Point of brake servo actuation Brake pressure 800 mbar vacuumLower vacuum level (e.g. cold start)Braking assistance by means of OHBS function Foot pressureS321_06230Function The loss of braking assistance, as a result of insufficient vacuum pressure, is balanced out with an active and controlled build-up of brake pressure from the ESP hydraulics. To enable this control, measurement of the pneumatic forces in both chambers of the brake servo (BS) is necessary. The pressure difference is a direct benchmark for the maximum amount of braking assistance available. If the pressure in both chambers is equaI, the point of brake servo actuation is reached. Thereafter, a further increase in braking force is only possible, without additional braking assistance, by an increase in foot pressure on the brake pedal. Stored in the ESP control unit J104 is the specified map characteristic for the build-up of brake pressure, depending on the pressure difference in both servo chambers. If the intake manifold vacuum is insufficient, the point of actuation is reached even at brake pressure levels below the specified amount. If this is the case, a controlled build-up of brake pressure is initiated by the ESP hydraulics. Compared to conventional braking assistance, the driver will notice no difference here with regards to the force required at the brake pedal and braking comfort. To enable the controlled build-up of brake pressure, the use of new solenoid valves is made to switch to ESP regulated mode. The degree to which these valves is opened can be controlled on a time basis. In this way, the pressure patterns can be adapted to each situation.31Brake systemDifferential pressure sensor The sensor measures the pneumatic pressures in both chambers of the brake servo.S321_064Installation position of differential pressure sensor shown as cross-sectional diagramVacuum pressure Differential pressure sensor chamberWorking pressure chamberBrake servoS321_066Signal application The differential pressure sensor calculates the difference in brake servo pressure conditions to atmospheric pressure. For OHBS regulation, however, only the pressure in the vacuum pressure chamber is used.Effects of failure If the signal from the working pressure chamber should fail, an entry is made in the fault memory. The OHBS function remains intact. In the event of signal failure in the vacuum pressure chamber, an entry is made in the fault memory and the brake system warning lamp K118 will light up.32The exchange of ESP and CAN dataThe ESP control unit exchanges data with other control units of the onboard electrical system.J220 Motronic control unit J104 ESP control unit J217 Automatic gearbox control unitJ533 Data bus diagnostic interfaceJ492 Four-wheel drive control unitJ527 Steering column electronics control unit G85 Steering angle senderDiagnosis connectionJ500 Electromechanical power steering control unitS321_180J285 Control unit with display in dash panel insertDrivetrain CAN data bus Diagnostic CAN data busDash panel CAN data bus Data bus wiring33Brake systemThe handbrakeThe new design means that the amount of space required in the centre console has been minimised. In this way, additional stowage facilities have been created behind the handle. The lever is pressure cast from magnesium. This resulted in a weight saving of more than half that of the steel version.S321_073The toothed segment is joined positively to the bearing bracket. In the neutral position, the pawl is engaged with the toothed segment and the brake lever is locked.When the release button is pressed, the pawl is pulled away from the toothed segment and the brake lever is free to move.S321_201S321_20334Wheels and tyresThe wheels and tyresEquipment overviewTyre size 195/65/ R 15 91 T 195/65/ R 15 91 T/H 195/65/ R 15 91 T/H 205/60/ R 15 91 H 205/55/ R 16 91 H/V/W 205/55/ R 16 91 Q 205/45/ R 17 91 H/V Spare wheel of emergency type T125/70/ R 18 Spare wheel of conventional type or TirefitProfile Summer Summer Winter Summer Summer Winter Summer -Rim size 6 J x 15 offset 47 6.5 J x 15 offset 50 6 J x 15 offset 47 6 J x 15 offset 47 6.5 J x 16 offset 50 6 J x 16 offset 50 7 J x 17 offset 54 3.5 J x 18Rim type Steel Alloy Steel Alloy Alloy Alloy Alloy -Tyre monitoring system The tyre monitoring system is a software module in the ABS control unit. It detects slow punctures and gradual tyre pressure loss at the wheel.More detailed information can be found in self-study programme SSP 319 "The Golf 2004 Electrical system".35Pedal clusterThe pedal clusterThe foot pedal cluster was adapted to the Golf. Accelerator pedal, clutch and brake actuation are of a modular design.To remove the accelerator pedal module, please use special tool T10238 or T10240.S321_087The clutch position sender G476Fitting location The clutch position sender is clipped onto the master cylinder. This sender detects when the clutch pedal is actuated.Signal application With the clutch pedal actuated,● ●the cruise control system is switched off and the amount of fuel injected is reduced briefly to prevent gear change jolts.Clutch pedal with clutch position senderS321_19536How it worksBearing bracket PlungerThe master cylinder is attached to the bearing bracket via a bayonet connection. When the clutch pedal is actuated, the plunger moves the piston in the master cylinder.Clutch master cylinderClutch position sender Piston with permanent magnet Pedal travel S321_204Clutch pedal not pressed When the clutch pedal is not pressed, the plunger and piston are in the rest position. The electronic evaluation feature of the clutch position sender sends a voltage signal to the engine control unit, which is 2 volts under the supply voltage (battery voltage). The engine control unit thereby detects that the clutch pedal is not pressed.Piston with permanent magnet PlungerS321_224 Switch point (Hall sender) Clutch position sender Voltage signal to engine control unitClutch pedal pressed When the clutch pedal is pressed, the plunger is pushed together with the piston in the direction of the clutch position sender. At the front end of the piston is a permanent magnet. As soon as the permanent magnet passes over the switch point of the Hall sender, the electronic evaluation feature now only sends a voltage signal of 0 to 2 volts to the engine control unit. In this way, it detects that the clutch pedal is pressed.Piston with permanent magnetPlungerS321_226Switch point (Hall sender) Clutch position sender Voltage signal to engine control unit37Pedal clusterThe accelerator pedal position senders G79 and G185Both accelerator pedal position senders are part of the accelerator pedal module and operate without contact as inductive senders. Advantages - No wear as senders operate without contact - No basic setting for kick-down necessary as sender is part of accelerator pedal module, which therefore does not result in tolerances between accelerator pedal and vehicle bodySignal application The engine control unit uses the accelerator pedal position sender signals to calculate the amount injected.S321_217 Accelerator pedal with accelerator pedal position sendersEffects of signal failure In the event of failure in one or both senders, an entry is made in the fault memory and the electronic power control (EPC) warning lamp will be activated. The convenience features, such as cruise control or engine braking control will be deactivated.If one sender fails the system will adopt the idle position. If the second sender is detected at idle within a defined test period, normal driving mode will be authorised again. If a full throttle input is made, speed will increase only slowly.If both senders fail the engine will only run at increased idling speed (max. 1500 rpm) and will no longer respond to input from the accelerator pedal.38Construction The accelerator pedal module comprises of an accelerator pedal, the pedal end stop, the mechanical components to convert rotational motion and both accelerator pedal position senders G79 and G185. The senders are joined to a circuit board and each consist of an exciter coil, three receiver coils and electronics for control and evaluation. For reasons of safety, both senders operate independently of each other.Mechanical components S321_219 Cover Circuit boardAccelerator pedalSmall metal plateThe mechanical components of the accelerator pedal module convert leverage movement of the accelerator pedal into straight line motion.A small metal plate is attached so that when the accelerator pedal is actuated, it is brought in line just short of the circuit board.Accelerator pedal not pressedAccelerator pedal pressedMechanical Mechanical components Small metal plate S321_220 S321_222 Circuit board Area of receiver coils Circuit board Exciter coils Small metal plate components39Pedal clusterHow it works Supplied with 5V of power, the pedal electronics generate a high frequency alternating voltage, which results in the build-up of an electromagnetic alternating field. This electro-magnetic alternating field affects one moving small metal plate. As this happens, a further electromagnetic alternating field is generated around the small metal plate. This location-dependent alternating field influences the receiver coils, inducing a relevant alternating signal there.J248 Diesel direct injection system control unit Electronics for Exciter coils Small metal plate S321_228 evaluationReceiver coilsElectro-magnetic alternating field of small metal plateElectro-magnetic alternating field of exciter coilThe strength of the induced alternating voltage depends largely on the position of the small metal plate. Each position results in a different coverage of the small metal plate to the receiver coils. In the idle position, the coverage is at its lowest and, therefore, so is the induced alternating voltage. In the full throttle, i.e. kick-down position on automatic gearboxes, coverage is at its greatest and, therefore, so is the alternating voltage.S321_230Small metal plate in idle positionSmall metal plate in full throttle position Kickdown areaAccelerator pedal position travelThe electronics for evaluation set the alternating voltages of the three receiver coils at a common value, they amplify them and bring the output voltages of the three receiver coils together into the equation. Following voltage evaluation, the result is converted into a linear voltage signal and sent on to the engine control unit.Signal voltage in voltsEvaluationDriver input percentage S321_232 Full throttle stop Accelerator pedal end stop40ServiceThe axle geometryInstalled in the Golf is an adjustable rear axle, e.g. track and camber can be changed independently of each other.The track is adjusted via an eccentric bolt between lower link and subframe.S321_116S321_120The camber is adjusted via an eccentric bolt. This eccentric bolt joins the link to the subframe.To adjust the camber, special tools● ●S321_118shock absorber set T10001 and ring spanner T10179 are required.41ServiceSpecial toolsDesignationToolApplicationT10179 Ring spannerFor adjusting camber on rear axle in conjunction with shock absorber set T10001S321_114T10219 (1) Sleeve T10219 (2) Drift(1)For renewing bonded rubber bush on wishbone of front axle (2)S321_112T10149 SupportFor adjusting unladen weight position of bonded rubber bushes on front and rear axleS321_194T10238 (1) T10240 (2)(1)(2)Release tool for accelerator pedal module, LHD (1) and RHD (2)S321_20042Test yourself1. What is so special about the four link rear axle? a) Oversteer is achieved by means of a predefined change in the wheel position during cornering. b) Separation of longitudinal and lateral connection. c) Cracks and grooves running across the road surface are absorbed easily.2.Of which components is the electro-mechanical power steering comprised? a) Steering column, mechanical steering gear and hydraulic pump. b) Steering angle sender, steering column, steering force sender, control unit, electric motor and steering gear. c) Steering angle sender, steering column, steering force sender, yaw rate sender and swivel mounting.3.What is the role of OHB-V? a) OHB-V measures the brake pressure applied by the driver via the brake pedal. b) The loss of braking assistance, as a result of insufficient vacuum pressure, is balanced out with an active and controlled build-up of brake pressure from the ESP hydraulics. c) Due to modifications to the interior of the brake servo, it makes high braking pressures available even at low pedal forces.1.) b, c; 2.) b; 3.) b Answers 43321© VOLKSWAGEN AG, Wolfsburg, VK-36 Service Training All rights and the right to make technical alterations reserved 000.2811.42.20 Technical status 09/03❀ This paper was manufactured from pulp thatwas bleached without the use of chlorine.